Quick Start Guide5.1.2CH Soundbar with wireless subwoofer & Dolby AtmosModel: HS512

1

2

Remote control

What’s in the Box

Adapter (for Main Unit)

3.5mm to 3.5mmaudio Cable

Main Unit Remote Control / AAA Batteries x 2

Wireless Subwoofer

Wall mountingScrewWall BracketAC power Cord x2

HDMI Cable

Quick Start Guide

1 Switch the unit between ON and STANDBY mode.

2 MUTE Mute or resume the sound.

3 SOURCE Select the play function.

4 BT Select the Bluetooth mode.

5 VOL+/VOL- Increase/decrease the volume level.

6 / Skip to previous/next track in Bluetooth/USB mode.

7 /PAIR Play/pause/resume playback in Bluetooth/USB mode.

Press and hold to activate the pairing function in Bluetooth mode or disconnect the existing paired Bluetooth device.

8 EQ Select a preset sound e�ect.

9 SURROUND Adjust the surround ON/OFF.

10 DIMMER+/- Adjust display brightness.

11 BASS+/- Adjust bass level.

Replace the Remote Control Battery1 Press and slide the back cover to

open the battery compartment of the remote control.

2 Insert two AAA size batteries (included). Make sure the (+) and (–) ends of the batteries match the (+) and (–) ends indicated in the battery compartment.

3 Close the battery compartment cover.

Identifying the Parts

8

aux

4 3

6 7 8

1 2 3

9 1210 11 13 14 1615

5

32

1 1 2

Identifying the Parts

Main Unit

1 Overhead Sound2 Surround Speakers3 Display Window Show the current status.4 Remote Control Sensor Receive signal from the remote control.5 Screws Remove the screws then install the wall

mounting screws into the back of the unit.6 (ON/OFF) button Switch the unit between ON and Standby mode.7 (SOURCE) button Select the play function.8 VOL+/VOL- buttons Increase/decrease the volume level.9 DC IN 23V Socket Connect to adapter.10 COAXIAL Socket11 OPTICAL Socket12 USB Socket Insert the USB device to play music. 13 AUX Socket Connect to an external audio device.14 HDMI OUT (ARC) Socket Connect to a TV via HDMI cable.15 HDMI IN 1 Socket16 HDMI IN 2 Socket

Wireless Subwoofer1 AC~ Socket Connect to power.2 PAIR button Press activate the pairing function between the main unit and the subwoofer.3 PAIR Indicator Light up solidly when the pairing succeed.

Connections3

5 Wall Mounting

4

◎ Pairing the Wireless Subwoofer with the Main Unit

HDMI IN

HDMI (ARC)

OR

OPTICALCOAXIAL AUDIO OUT Headphone

AB

AV equipment

HDMI OUT

● Before connecting the AC power cord, ensure you have completed all other connections.

● DolbyAtmos● DTS: X

Dolby Atmos® / DTS: X is available only in HDMI mode.

1. To use Dolby Atmos® / DTS: X in HDMI 1 and HDMI 2 mode, Your TV had to support Dolby Atmos® / DTS: X or HDMI audio passthrough.

2. Make sure that “No Encoding“ is selected for bitstream in the audio output of the connected external device (e.g. Blu-ray DVD player, TV etc.).

3. While entering Dolby Atmos / DTS: X / Dolby Digital / PCM format, the soundbar will show DOLBY ATMOS / DTS: X / DOLBY AUDIO / PCM AUDIO.

4. While the soundbar is using Dolby Atmos / DTS: X audio, you can only adjust the bass level of the subwoofer. All other EQ e�ects will not be available.

1106 mm

1 3

4

2

1106 mm

（ø5.5~6mm / 32mm）

13PAIR

3s

2

◎ 开机/关机� 按本机顶壳或遥控器上的 键开机；

� 再次按 键即可待机。

� 如果你想彻底关闭本机，需将电源线从电源插座拔下。

提示：

当重新开机时，本机会切换至您上次最后选择的音源。

在无任何音源信号输入、无设备连接或暂停播放的情况下，15分钟后主机会自动关机。

◎ 功能选择 重复按主机或遥控器上的 / SOURCE 键或按遥

控器上的 HDMI 键选择相应的AUX, OPTICAL, COAXIAL, HDMI 1, HDMI 2, HDMI ARC, USB 和 BT（蓝牙） 播放功能，相应的功能播放将显示在显示屏上。

◎ 调整音量 播放时，按+（音量+）键增加音量，按-（音量-）

键减小音量。

播放时，按 MUTE 键静音，再按一次 MUTE 键或音量+/-键还原声音。

◎ 调整显示屏亮度 如需调整显示的亮度，重复按 DIMMER键降低或提

高亮度。

◎ 调整低音音效 按遥控器上的BASS按键激活低音设置，然后按

VOL +/-按键调节低音效果（bass+5 ~ bass-5）。

◎ 打开/关闭环绕声 按遥控器上的 SURROUND按键打开环绕声。 再

次按此按钮可关闭环绕声。

◎ 选择预设音效 反复按遥控器上的EQ按键来选择不同的音效：

MOVIE（推荐用于观看电影）、MUSIC（推荐用于听音乐）、NEWS（推荐用于看新闻） SPORT（推荐用于运动音乐)、Night（晚上模式)。

Basic Operation

Removethe screws

Install the wallmounting screws

◎ Standby/ONWhen you �rst connect the main unit to the mains socket, the main unit will be in Standby mode.• Press the button on the unit or on the remote control

to switch the unit ON.• Press the button again to switch the unit back to

STANDBY mode. • Disconnect the mains plug from the mains socket if you

want to switch the unit OFF completely.- If a TV or an external device is connected, the unit will

switch on automatically when the TV or the external device is switched on.

- When there is no input signal from the unit in over 15 minutes, then it will automatically switch to Standby mode.

◎ Select ModesPress the (SOURCE) button repeatedly on the unit or the SOURCE, BT buttons on the remote control to select the AUX, OPTICAL, COAXIAL, HDMI 1, HDMI 2, HDMI ARC, USB and BT (Bluetooth) mode. The selected mode will show on the display.

◎ Adjust the Bass LevelPress the BASS +/- buttons on the remote control to adjust bass level. (bass +5 ~ bass -9).

◎ Turn the Surround Sound ON/OFFPress the SURROUND button on the remote control to turn on the surround sound. Press this button again to turn o� the surround sound.

◎ Adjust the VolumePress the VOL+ / VOL- buttons on the unit or on the remote control to adjust the volume.If you wish to turn the sound o�, press the MUTE button on the remote control. Press the MUTE button again or press the VOL+ / VOL- buttons on the unit or on the remote control to resume normal listening.

◎ Adjust the BrightnessPress the DIMMER +/- button on the remote control to select brightness level.

◎ Select a Preset Sound E�ectWhile playing, press the EQ button on the remote control to select desired preset equalizers: MOVIE, MUSIC, NEWS, SPORT.