FOREWORD This manual contains on-vehicle service and/or diagnosis procedures for the Mazda3, MAZDASPEED3.
For proper repair and maintenance, a thorough familiarization with this manual is important, and it should always be kept in a handy place for quick and easy reference.
All the contents of this manual, including drawings and specifications, are the latest available at the time of printing. As modifications affecting repair or maintenance occur, relevant information supplementary to this volume will be made available at Mazda dealers. This manual should be kept up-to-date.
Mazda Motor Corporation reserves the right to alter the specifications and contents of this manual without obligation or advance notice.
All rights reserved. No part of this book may be reproduced or used in any form or by any means, electronic or mechanical-including photocopying and recording and the use of any kind of information storage and retrieval system-without permission in writing.
Mazda Motor Corporation HIROSHIMA, JAPAN
APPLICATION: This manual is applicable to vehicles beginning with the Vehicle Identification Numbers (VIN), and related materials shown on the following page.
CONTENTS
Title
RESTRAINTS
BODY &ACCESSORIES
ALPHABETICAL INDEX
© 2006 Mazda Motor Corporation PRINTED IN U.S.A., JULY 2006 Form No. 1886-1U-06G Part No. 9999-95-0178-07
VEHICLE IDENTIFICATION NUMBERS (VIN)
JM1 JM1 JM1 JM1 JM1 JM1 JM1 JM1 JM1 JM1 JM1 JM1 JM1 JM1 ..IM1 JM1
BK123*7# BK124*7# BK12F*7# BK12G*7# BK143*7# BK144*7# BK14L*7# BK14M*7# BK323*7# BK324*7# BK32F*7# BK32G*7# BK343*7# BK344*7# BK34L*7# BK34M~i~7#
600001­ 600001­ 600001­ 600001­ 600001­ 600001­ 600001­ 600001­ 600001­ 600001­ 600001­ 600001­ 600001­ 600001­ 600001­ 600001­
RELATED MATERIALS
I Material Name MNAO Part No. Mazda Material No. I i 2004 Mazda3 Service Highlights 9999-95-064F-04 3385-1 U-031
I 200S Mazda3, Mazda MX-S Miata, Mazda MX-S, MAZDASPEED 9999-9S-MODL-OS 3400-1U-04H
MX-S, Mazda MPV, Mazda RX-8 Service Highlights
2006 Mazda3, Mazda MPV Service Highlights 9999-9S-M PV3-06 3408-1 U--0SG
2007 Mazda3, MAZDASPEED3, MazdaS, Mazda6, 9999-9S-MODL-07 3422-1 U-06G
MAZDASPEED6, Mazda MX-S, Mazda RX-8 Service Highlights
'1 99S. 1996, 1997, 1998, 1999,2000 08D-11 Service Highlights 9999-9S-08D2-00 3344-1U-99K
Engine Workshop Manual L3 WITH TC 9999-9S-0L3T-06 1833-1 U-OSH
Engine Workshop Manual LF, L3 9999-9S-LFL3-OS 1866-1U--0SH
Manual Transaxle Workshop Manual G3SM-R 9999-95-0G3S-03 17S6-1 U-021
Manual Transaxle and Transfer Workshop Manual A26M-R, 9999-9S-A26M-07 1898-1 U-06G
A26MX-R
i Automatic Transaxle Workshop Manual FSSA-EL 9999-9S-FSSA-06 18S9-1U-OSF
2004 Mazda3 8odyshop Manual 9999-9S-036F-IJ4 3386-1 U-03J
2007 Mazda3 Wiring Diagram 9999-9S--019G--07 S677-1U-06G
~~G_E_NE_R_A_L_IN_F_O_R_M_AT_I_ON~~I~I~ GENERAL INFORMATION .... 00-00
00-00 GENERAL INFORMATION VEHICLE IDENTIFICATION NUMBER Dynamometer 00-00-18
(VIN) CODE 00-00-2 SST 00-00-18 VEHICLE IDENTIFICATION INSTALLATION OF
NUMBER (VIN) 00-00-2 RADIO SySTEM '" 00-00-19 HOW TO USE THIS MANUAL 00-00-3 ELECTRICAL SYSTEM 00-00-19
Range of Topics 00-00-3 Electrical Parts 00-00-19 Service Procedure 00-00-3 Wiring Harness 00-00-19 Symbols 00-00-5 Connectors 00-00-20 Advisory Messages 00-00-5 Terminals 00-00-21 Troubleshooting Procedure 00-00-6 Sensors, Switches, and Relays 00-00-21 Procedures for Use 00-00-7 Wiring Harness 00-00-22
UNITS 00-00-12 Fuse 00-00-22 Conversion to SI Units Direction of View for Connector 00-00-22
(Systeme International d'Unites) 00-00-12 Electrical Troubleshooting Tools 00-00-23 Rounding Oft. 00-00-12 Precautions Before Welding 00-00-24 Upper and Lower Limits 00-00-12 JACKING POSITIONS, VEHICLE LIFT
SERVICE CAUTIONS 00-00-13 (2 SUPPORTS) AND SAFETY STAND Injury/damage Prevention (RIGID RACK) POSITIONS 00-00-25
Precautions 00-00-13 Jacking Positions 00-00-25 Protection of the Vehicle 00-00-13 Vehicle Lift Positions 00-00-26 Preparation of Tools and Measuring Safety Stand Positions 00-00-26
Equipment. 00-00-13 TOWING 00-00-27 Special Service Tools 00-00-13 Towing 00-00-27 Malfunction Diagnosis System 00-00-13 Tiedown Hooks 00-00-28 Disconnection of the Negative TIEDOWN HOOK 00-00-29
Battery Cable 00-00-14 IDENTIFICATION NUMBER Oil Leakage Inspection 00-00-14 LOCATIONS 00-00-30 Removal of Parts 00-00-14 Vehicle Identification Number Disassembly 00-00-15 (VIN) 00-00-30 inspection During Removal, Engine Identification Number 00-00-30
Disassembly 00-00-15 SAE STANDARDS 00-00-31 Arrangement of Parts 00-00-15 ABBREVIATIONS 00-00-32 Cleaning of Parts 00-00-15 PRE-DELIVERY INSPECTION 00-00-32 Reassembly 00-00-16 Pre-Delivery Inspection Table 00-00-32 Adjustment 00-00-16 SCHEDULED MAINTENANCE 00-00-34 Rubber Parts and Tubing 00-00-16 Scheduled Maintenance Table for U.S.A., Hose Clamps 00-00-17 CANADA and Puerto Rico 00-00-34 Torque Formulas 00-00-17 Scheduled Maintenance Vise 00-00-17 Table for Mexico 00-00-36
00-00-1
Plant
*= 0 to 9, X
F= 2.0 L (Federal/CANADA (LF)) 3= 2.3 L (Federal/CANADA (L3)) L= 2.3 L Turbo (Federal/CANADA (L3 WITH TC)) G= 2.0 L (California (LF)) 4= 2.3 L (California (L3)) M= 2.3L Turbo (California (L3 WITH TC))
4= 5HB 2= 4SD
3= with Side air bag module, Curtain air bag module
1= without Side air bag module, Curtain air bag module
BK= Mazda3, Mazdaspeed3
JM1= Mazdalpassenger car
VEHICLE IDENTIFICATION NUMBER (VIN)
JM1 BK123*7# 600001­ JM1 BK124*7# 600001­ JM1 BK12F*7# 600001­ JM1 BK12G*7# 600001­ JM1 BK143*7# 600001­ JM1 BK144*7# 600001­ JM 1 BK14L*7# 600001­ JM1 BK14M*7# 600001­ JM1 BK323*7# 600001­ JM1 BK324*7# 600001­ JM1 BK32F*7# 600001­ JM1 BK32G*7# 600001­ JM1 BK343*7# 600001­ JM1 BK344*7# 600001­ JM1 BK34L*7# 600001­ JM1 BK34M*7# 600001­
am3uuw0000076
id000000100300
00-00-2
Range of Topics id000000800100
• This manual contains procedures for performing all required service operations. The procedures are divided into the following five basic operations:
Removal/I nstallation Disassembly/Assembly Replacement •Inspection Adjustment
• Simple operations which can be performed easily just by looking at the vehicle (i.e., removal/installation of parts, jacking, vehicle lifting, cleaning of parts, and visual inspection) have been omitted.
Service Procedure Inspection, adjustment
• Inspection and adjustment procedures are SHOWS PROCEDURE ORDER divided into steps. Important points regarding the FOR SERVICE location and contents of the procedures are
explained in detail and shown in the illustrations.
SHOWS TIGHTENING TORQUE SPECIFICATIONS
~. 'Caution Connect the gauge set from under the vehicie to prevent contact with the drive belt and the cooling fan.
acxuuw00000434
00-00-3
GENERAL INFORMATION
Repair procedure 1. Most repair operations begin with an overview illustration. It identifies the components, shows how the parts fit
together, and describes visual part inspection. However, only removal/installation procedures that need to be performed methodically have written instructions.
2. Expendable parts, tightening torques, and symbols for oil, grease, and sealant are shown in the overview illustration. In addition, symbols indicating parts requiring the use of special service tools or equivalent are also shown.
3. Procedure steps are numbered and the part that is the main point of that procedure is shown in the illustration with the corresponding number. Occasionally, there are important points or additional information concerning a procedure. Refer to this information when servicing the related part.
SHOWS SERVICE Procedure ITEM (S)
... / INDICATES RELEVANT I LOWER TRAILING LINK, UPPER TRAILING LINK REMOVAUINSTALLATION I REFERENCES THAT NEED
"R III t II t'" 1.JaCkup therearotthevehlclea.ndsupport. it with safely stands. __--- TO BE FOLLOWED DURING emova ns a a Ion 2. Remove the undercover (See 01-10-4 Undercover Removal
Portion 3. Remove in the order indicated ,n the table INSTALLATIONU4. Install in the reverse order of removal. - - - - _.- - - - - - - - - - - - - - - - - -~-.- ~ 5. Inspect the rear wheel alignment and adjust it if necessary.
SHOWS TIGHTENING TORQUE UNITS
SHOWS TIGHTENING TORQUE SPECIFICATIONS
"Inspection After Installation" Portion
INSTALL THE PARTS BY PERFORMING STEPS 1-3 IN REVERSE ORDER
SHOWS PROCEDURE ORDER FOR SERVICE
"'-.",. , Split pm
(See O?-14-5 Lower Trailing Link Sal! Joint Removal Nole) 3
4 Bolt Lower traihno link Dust boot (lower trailing link)
5 6
8 Nul 9 Upper trailing link ball jOint
(See 02-14-5 Upper Trailing link Ball Joint Removal Note) 10 NUl 11 Upper trailing hnk
12 Dust boot (upper trailing link)
LowerTrailing Link Ball Joint, Upper Trailing Link Ball Joint Removal Note • Remove the ball jOint using the SSTs.
SHOWS SPECIAL SERVICE TOOL (SST) NO.
KNUCKLE
acxuuw00000435
00-00-4
GENERAL INFORMATION
Symbols • There are eight symbols indicating oil, grease, fluids, sealant, and the use of SST or equivalent. These symbols
show application points or use of these materials during service.
.. Symbol Meaning Kind
I Apply oil New appropriate engine oil or gear oil
•" . Apply brake fluid New appropriate brake fluid
I I • Apply automatic
I I, i
lID Use SST or equivalent
Appropriate tools
manual.
Warning • A Warning indicates a situation in which serious injury or death could result if the warning is ignored.
Caution • A Caution indicates a situation in which damage to the vehicle or parts could result if the caution is ignored.
Note • A Note provides added information that will help you to complete a particular procedure.
Specification • The values indicate the allowable range when performing inspections or adjustments.
Upper and lower limits • The values indicate the upper and lower limits that must not be exceeded when performing inspections or
adjustments.
00-00-5
WARNING L1GHT* ON/FLASHING
TROUBLESHOOTING FLOW
CUSTOMER ARRIVES
!
• ~
I
DIAGNOSE BY SYMPTOM (SYMPTOM TROUBLESHOOTING) 1. DIAGNOSTIC INDEX 2. QUICK DIAGNOSIS CHART
(IF MENTIONED) 3. SYMPTOM
TROUBLESHOOTING
acxuuw00000444
.. Diagnostic trouble codes (DTCs) are important hints for repairing malfunctions that are difficult to simulate. Periorm the specific DTC diagnostic inspection to quickly and accurately diagnose the malfunction.
.. The on-board diagnostic function is used during inspection. When a DTC is shown specifying the cause of a malfunction, continue the diagnostic inspection according to the items indicated by the on-board diagnostic function.
Diagnostic index .. The diagnostic index lists the symptoms of specific malfunctions. Select the symptoms related or most closely
relating to the malfunction.
Quick diagnosis chart (If mentioned) .. The quick diagnosis chart lists diagnosis and inspection procedures to be periormed specifically relating to the
cause of the malfunction.
00-00-6
Procedures for Use Using the basic inspection (section 05)
• Perform the basic inspection procedure before symptom troubleshooting. • Perform each step in the order shown. .. The reference column lists the location of the detailed procedure for each basic inspection. • Although inspections and adjustments are performed according to the reference column procedures, if the
cause of the malfunction is discovered during basic inspection, continue the procedures as indicated in the action column.
SHOWS INSPECTION
S EP INSPECTION
Perform the mecnanical system test. Yes (See 05-13-3 MECHANICAL SYSTEM TEST.) No Repair or replace any malfunctioning parts according to Is mechanical system normal? the inspection result.
2 Turn the Ignition switch to the ON position. Yes Go to next step. When the selector lever is moved, does the selector No Inspect the selector lever and TR sWitch. Repair or illumination indicate synchronized position to the replace malfunctioning parts. lever location? Also, when other ranges are selected (See 05-14-5 SELECTOR LEVER INSPECTION.) from N or P during idling. does the vehicle move (See 05-13-10TRANSMISSION RANGE (TR) SWITCH within 1-2 s? INSPECTION.)
If the selector iever and TR switch are normal, go to the next step.
3 Inspect the ATF color condition Yes Go to the next steD. (See 05-13-8 AUTOMATIC TRANSMISSION No Repair or replace any malfunctioning parts according to FLUID (ATF) INSPECTION.) The inspection resulT Are ATF color and odor normal? Flush ATX and cooler line as necessary.
4 Perform the line pressure test. Yes Go to the next step. (See 05-13-3 Line Pressure Test.) No Repair or replace any malfunctioning pans according to Is the line pressure normal? the inspection result
5 Perform the stall test. Yes Go to the next steD.
REFERENCE (See 05-13-4 Stall Speed Test.) No Repair or replace any malfunctioning parts according to
COLUMN Is the stall speed normal? the inspection result.
Inspect the voltage at the following TCM terminals. Yes Go to the next step.
(See 05-13-29TCM INSPECTION.) No
SHOW POINTS REQUIRING SHOWS ITEM NAMES FOR ORDER ATTENTION BASED ON DETAILED PROCEDURES
INSPECTION RESULTS
Go to the next step. 1
·· ·· ·
Terminal 2J (TFT sensor) Terminals 1D, 26, 2C, 2E (TR switch) Terminal 2G (turbine sensor) Terminal 2D (down switch) Terminal 21 (up sWitch) Terminal 1E (M range switch) Terminal 1W (steering shih switch)
Is the voltage normal? [
Using the DTC troubleshooting flow • DTC troubleshooting flow shows diagnostic procedures, inspection methods, and proper action to take for each
DTC.
I
I
I POSSIBLE CAUSE describes possible point(s) of malfunction
I Iindicates the inspection step No. to be performed (01 and 05 section)
STEP shows the order of troubleshooting
---..:..
I
DETECTION CONDITION
Diagnostic support note This is a continuous monitor (GeM).
MIL illuminates if PCM detects the above malfunction during first drive cycle. Therefore, PENDING CODE is nor available
FREEZE FRAME DATE is available.
DTC is stored in the PCM memory.
PCM monitors input voltage from TP sensor after ignition key is turned on. If Input voltage at PCM terminal 68 !
above 8.25 V. PCM determines thai TP Circuit nas malfunccion
POSSIBL CAUSE
Connector or terminal malfunction
Open circuit in wiring between MAF sensor terminal 0 and PCM terminal 36
o en circuit in MAF sensor round circuit
lP
FROM MAIN RELAY PCM TERMINAL D
MAF SENSOR HARNESS SIDE CONNECTOR
Diagnostic procedure describes the STEP INSPECTION ACTION appropriate
1 VERIFY FREEZE FRAME DATA HAS BEEN RECORDED
Yes
No
~
/ action to be taken
Has FREEZE FRAME DATA been recorded? to next step, according to 2 VERIFY RELATED REPAIR INFORMATION Yes Perform repair or diagnosis according to available repair the result
AVAILABILITY
Are related Service Bullelins and/or on-line
information. If vehicle is not repaired. then go to next step. (Yes/No) of the
repair information available? No Go to next steD. INSPECTION. 3 VERIFY CURRENT INPUT SIGNAL STATUS IS Yes Intermittent concern is existing. Go to INTERMITTENT
CONCERN INTERMITIENT OR CONSTANT
Access MAF V PID using diagnostic tool. No
CONCERNS TROUBLESHOOTING procedure. (See 01-03-33INTERMITIENT CONCERN _ TROUBLESHOOTING)
Go to next step.
Reference item(s) to perform
Is MAF V PID within 02 - 8.3 V?
4 INSPECT POOR CONNECTION OF MAF Yes Repair or replace terminals, then go to Step 8. ACTION. SENSOR CONNECTOR
Turn ignition key to OFF.
Disconnect MAF sensor connector
Check for poor connection (damaged, pulled- out terminals, corrosion etc.).
Are there any malfunctions?
DETECTION CONDITION describes the condition under which the DTC is detected.
Indicates the circuit to be inspected (01 and 05 section)
Indicates the connector related to the inspection
ACTION
acxuuw00000446
00-00-8
GENERAL INFORMATION
Using the diagnostic index • The symptoms of the malfunctions are listed in the diagnostic index for symptom troubleshooting. • The exact malfunction symptoms can be selected by following the index.
II NO. TROUBLESHOOTING ITEM DESCRIPTION Page
1 Melting of main or other fuses - (See 01·03·6 MELT NO.1 MAIN OR OTHER FUSE)
2 MIL comes on
Hard start/long crank/erratic start/erratic crank
MIL is illuminated incorrectly. (See 01·03·7 NO.2 MIL COMES ON)
3 Staner does not work. (See 01·03·8 NO.3 WILL NOT CRANK)
4 Starter cranks engine at normal speed but engine requires excessive cranking time before starting.
(See 01·03·9 NO.4 HARD START/ LONG CRANK/ERRATIC CRANK)
5 Engine stalls. I Mer starVat Idle
Cranks normally but will not start
Engine stops unexpectedly a1 Idle and/or after start.
(See 01·03·11 NO.5 ENGINE·STALLS AFTER START/AT IDLE)
6 Starter cranks engine at normal speed but engine will not run.
(See 01·03·15 NO.6 CRANKS NORMALLY BUT WILL NOT START)
7 Slow return to idle Engine takes more time than normal to return to idle speed.
(See 01·03·19 NO.7 SLOW RERUN TO IDLE)
Engine speed fluctuates between
8 Engine runs rough/rotling specified idle speed and lower speed and engine shakes
(See 01·03·20 NO.8 ENGINE RUNS ROUGH/ROLLING IDLE)
Fast idle/runs on
excessively.
9
Engine speed continues at last idle after warm-up. Engine runs after ignition key is turned to OFF
(See 01·03·23 NO.9 FAST IDLE/RUNS ON)
10 Engine stops unexpectedly at begin· ning of deceleration or recovery from deceleration.
(See 01·03·24 NO.1 0 LOW IDLE/ STALLS DURING DECELERATION)
acxuuw00000447
00-00-9
GENERAL INFORMATION
Using the quick diagnosis chart .. The chart lists the relation between the symptom and the cause of the malfunction. .. The chart is effective in quickly narrowing down the relation between symptom and cause of the malfunction. It
also specifies the area of the common cause when multiple malfunction symptoms occur. .. The appropriate diagnostic inspection relating to malfunction cause as specified by the symptoms can be
selected by looking down the diagnostic inspection column of the chart.
PART WHICH MAY BE THE SYMPTOM "' ­
/
~------------~-------------
x x x
x x x
x x
x x
x x x x x x
x x x x x x x
x x
4
6 Cranks normally but will not start
7 Slow return to idle 8 Engine runs rough/rolling Idle
9 Fast idle/runs on
MIL comes on
Will not crank
Enaine runs rough Misses
Cooling system concerns IRuns cold
Exhaust smoke Fuel odor (in engine cornpartment)
Enqine naise
AlC always onl AlC compressor runs continuously
AlC does not CUt off under wide open throttl conditions
Exhaust sulphur smell
Fuel retiJJ concerns Fuel fi1Iina shut oft issues Intermittent concerns
Constant voltaqe
trouble symptom.
STEP shows the order of troubleshooting.
Diagnostic procedure
Reference item(s) for additional ­ information to perform INSPECTION.
INSPECTIO describes the method to quickly determine t he malfunctioning part(s).
7ROUBLE SYMPTOM
Engine flares up or slips when upshifting or down shifting
r--. When accelerator pedal is depressed for driveway, engine speed increase but vehicle speed increase
DESCRIPTION
14 ...............
slowly.
• When accelerator IS depressed while driving, engine speed increases but vehicle not.
- • There is clutch slip because clutch is stuck or line pressure is low
Clutch stuck. slippage (forward clutch. 3-4 clutch, 2-4 brake band, one-way clutch 1, one-way clutch 2)
• Line pressure low • Malfunction or mis-adjustment of TP sensor
• Malfunction of VSS
• Malfunction of input/turbine speed sensor
• Malfunction of sensor grouno • Malfunction of shift solenoid A, B or C
• Malfunction of TCC solenoid valve POSSIBLE
o Malfunction of body ground CAUSE
o Malfunction of throttle cable
• Malfunction of throttle valve body
- Poor operating 01 mechanical pressure
• Selector lever position dispamy • TR switch position disparity
Note • Before following troubleshooting sreps, make sure that Automatic Transaxle On-board Diagnostic and
Automatic Transaxle Basic Inspection are conducted.
INSPECTIONSTEP
No
-=­ • Is shIft point okay? Yes
_ (See 05-17-5 ROAD TEST) No
Yes• Stop engine and turn ignition sWitch on. 3 • Connect diagnostic tool to DLC-2.
• Simulate SHIFT A, SHIFT B and SHIFT C PIDs forON.
o Is operating sound of shift solenoids heard?
N_~
• Verify test results.
- If okay, return to diagnostic index to service any additional symptoms.
- If malfunction remains, Inspect related Service Bulletins and/or On-line Repair Information and perform repair or diagnosis
- II vehicle is repaired, troubleshooting completed.
- If vehicle IS not repaired or addItional diagnostic information is not available, replace or reprogram PCM.
4
taken according to the result (Yes/No) of the INSPECTION.
-.-.How to perform ACTION is described in the relative material shown.
Reference tem(s) to perform ACTION.
Go to next step.
RepaIr or replace any defective parts according to inspection results.
Go to next step
Go to symptom troubleshooting NO.9 "Abnormal shift".
o Overhaul control valve body and repair or replace any defective parts.
(See ATX Workshop Manual GF4A-EL (1666-1A-99F))
• If problem remains, replace or overhaul transaxle and repair or replace defective parts.
(See 05-17-15 AUTOMATIC TRANSAXLE REMOVEVAUINSTALLATION)
No lnspect for bend, damage, corrosion or loose connection if shift solenoid A, B, or C terminal on ATX.
Inspect for shift solenoid mechanical stuck.
I
(See 05-17-14 Inspection of Operation
•
GENERAL INFORMATION
UNITS id000000801600
Electric current A (ampere) Electric power W (watt) Electric resistance ohm Electric voltage V (volt)
Length mm (millimeter) in (inch) kPa (kilo pascal)
Negative pressure mmHg (millimeters of mercury) inHg (inches of mercury) kPa (kilo pascal)
Positive pressure kgf/cm2 (kilogram force per square centimeter) psi (pounds per square inch)
Number of revolutions rpm (revolutions per minute)
I
I ITorque
N·m (Newton meter) kgf·m (kilogram force meter) kgf·cm (kilogram force centimeter)
r I
ft·lbf (foot pound force) ! in·lbf (inch pound force)
L (liter) US qt (U.S. quart) Imp qt (Imperial quart)
Volume ml (milliliter) cc (cubic centimeter) cu in (cubic inch) fl oz (fluid…