19-OTA105204 OptiX OSN Ethernet Services Configuration(Manual Configuration) ISSUE 1.21

7/30/2019 19-OTA105204 OptiX OSN Ethernet Services Configuration(Manual Configuration) ISSUE 1.21

1/88

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved

www.huawei.com

Internal

OptiX OSN 1500250035007500

Ethernet Services Configuration

(Manual Configuration)


2/88

HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 1

Upon completion of this course, you will be

able to:

Explain the menu of iManager T2000 forEthernet Services

Describe the process of configuring

Ethernet Services on the T2000

Learn how to configure Ethernet Services


3/88


Chapter 1 The Basic Concepts

Chapter 2 The EPL Service Configuration

Chapter 3 The EPLAN Service Configuration

Chapter 4 The EVPL Service Configuration


4/88


Tag flag is used to identify the type of packets. Three types of TAG flags

are available: tag aware, access, and hybrid.

Tag Aware: When the port is set to be tag aware, the port transmits

the packets with the Tag flag transparently and discards those

without the Tag flag

Access: When the port is set to be access, the port attaches a Tag

flag to the packets without Tag flag according to its VLAN ID and

discards those with the Tag flag.

Hybrid: When the port is set to be hybrid, the port can processpackets regardless of the Tag flag and attach a Tag flag to the

packets without the Tag flag according to its VLAN ID.

Tag flag:

Parameters for the Ethernet interface


5/88



Tag flag Untag flag

Tag aware (In) Transmit transparently discard

Tag aware (Out) Transmit transparently

Access (In) discard attach a Tag flag (default Vlan)

Access (Out) Delete the Tag flag (default Vlan)

Hybrid (In) Transmit transparently attach a Tag flag (default Vlan)

Hybrid (Out)If Vlan is the same, delete the Tag flag,

otherwise transmit transparently

PortPackets


6/88



VLAN ID:

VLAN ID of the port (MAC or VCTRUNK).

Working mode:

It can be set to auto-negotiation, 10 Mbit/s half/full-duplex,100 Mbit/s half/full-duplex or 1 Gbit/s full-duplex. The

Ethernet interfaces of the interconnected equipment shouldwork under the same fixed working mode; otherwise, thepacket may be lost and the rate may decrease, or theservice may be completely interrupted upon large volume oftraffic.

Port type:

There are two types: P and PE. Provider edge (PE) is themarginal port of the service provider. Provider (P) is thecore network port of the service provider. Port type isneeded when configuring EVPL and EVPLAN services.


7/88HUAWEI TECHNOLOGIES CO., LTD. All rights reserved Page 6


LCAS enable:

Maximum packet length:

Whether to enable LCAS.

Set this item for the external port, 1522 bytes by default.

Mapping protocol:

It is preferable to select the default- GFP mapping protocol.


8/88


Reference: G.8010 /Y.1306 (G.ethna),

G.8011 (G.ethsrv),

G.8012.1 (G.eota.1).

Ethernet Services Types EPL: Ethernet Private Line Service.

EPLAN: Ethernet Private LAN Service .

EVPL: Ethernet Virtual Private Line Service.

EVPLAN: Ethernet Virtual Private LAN Service.


9/88







10/88


For EPL Service, there are three types:

the Point-to-Point EPL Service

the MAC Shared EPL Service

the VCTRUNK Shared EPL Service

Configuring the EPL Service


11/88



Configuring the Point-to-Point EPL Service:

Engineering Requirements

Engineering Planning

Configuration Process


12/88




User Service requirement Source station Sink station Bandwidth

A Point-to-point NE1 NE5 10 Mbit/s

B Point-to-point NE1 NE5 40 Mbit/s

STM-16two-fiberbidirectional MSP ring

T2000

STM-4two-fiber

bidirectional non-protection chain

NE1

NE2

NE3

NE4

NE5



13/88





Step 1: Networking Diagram

Step 2: Board Information of Each NE

Step 3: Service Configuration Diagram of Each NE

Step 4: Timeslot Allocation Diagram


14/88


A B

STM-16 two-fiberbidirectional MSP ring

T2000

STM-4 two-fiberbidirectional non-protection chain

NE1

NE2

NE3

NE4

NE5

A B

VC-Trunk

MAC1 MAC2

MAC1 MAC2

Company A Service

Company B Service




15/88


Board layout of NE1




16/88


Board layout of NE5




17/88


VC4-4:VC12-1~VC12-5

MAC1

A10M

40M

B

VCTRUNKMAC

MAC2

VCTRUNK1

VCTRUNK2

VC-4-1:VC-3-1

SDHVC4-4:VC12-1~VC12-5

VCTRUNK

VCTRUNK1

VCTRUNK2

VC-4-1:VC-3-1

MAC1A

10M

40M

B

MAC

MAC2

NE1NE5

Service configuration diagram




18/88



Service Attribute A B

Source NE NE1 NE1

Source board - port 13-N1EFS4-1 13-N1EFS4-2

Source timeslot VC4-4: VC12-1VC12-5 VC4-1: VC3-1

Source VCTRUNK VCTRUNK1 (Tag aware) VCTRUNK2 (Tag aware)

Working mode of source MAC port Auto negotiation Auto negotiation

TAG flag of source MAC port Access Access

VLAN ID of source MAC port 1 2

Bound bandwidth 5 x VC-12 1 x VC-3

Sink NE NE5 NE5

Sink board - port 15-N1EFS4-1 15-N1EFS4-2

Sink timeslot VC4-4: VC12-1VC12-5 VC4-1: VC3-1

Sink VCTRUNK VCTRUNK1 (Tag aware) VCTRUNK2 (Tag aware)

Working mode of sink MAC port Auto negotiation Auto negotiation

TAG flag of sink MAC port Access Access

VLAN ID of sink MAC port 1 2



19/88



Timeslot

NE2Station NE3 NE4NE1

12-SL16-1

NE1

7-SL16-112-SL16-1 7-SL16-112-SL16-1 7-SL16-1 12-SL16-1 7-SL16-1

Forward

NE5NE4

13-SL4-1 7-SL4-1

Ring

Chain

Add/Drop

VC-4-313-EFS4: VC4-4

VC-12: 1-5

VC-4-413-EFS4: VC-4-1

VC-3: 1

VC-4-3

VC-4-4

15-EFS4: VC4-4

VC-12: 1-5

15-EFS4: VC-4-1

VC-3: 1

Station



20/88





Step 1: Creating a board

Step 2: Configuring Ethernet interfaces

Step 3: Configuring binding paths

Step 4: Creating the point-to-point EPL service

Step 5: Configuring committed access rate (CAR)

(Optional )

Step 6: Configuring the cross-connect from Ethernet

boards to SDH line boards


21/88




Right click


22/88


Configuring the EPL Service Step 2: Configuring Ethernet interfaces

Right click

Left click

Left click


23/88


Configuring the EPL Service Step 3: Configuring binding paths

Left click

Left click

Left click

Left click


24/88



Step 4: Creating the point-to-point EPL service

Left clickLeft click


25/88



Left click

Step 4: Configuring committed access rate (CAR) (Optional )

Left click


26/88



Step 6: Configuring the cross-connect from Ethernet boards to SDH line boards

Left click Left clickLeft click


27/88


Summary

Creating an Ethernet board

Configuring Ethernet interfaces

External Port: Basic Attributes, Tag Attribute

Internal Port: Tag Attribute, LCAS

Configuring binding paths: Configurable Ports, Level, Direction, Available VC4, timeslots

Creating the MAC shared EPL service:

Service Type, Service Direction, Ports, VLAN, TAG, Port Type

Configuring committed access rate (CAR):

CAR ID, Capacity, Ports

Configuring the cross-connect from Ethernet boards to SDH line boards


28/88








29/88



Configuring the MAC Shared EPL Service :





30/88



T2000

STM-4two-fiberbidirectional non-

protection chain

NE1

NE2

NE3

NE4

NE5



Configuring the MAC Shared EPL Service:

Source User Service requirement Source station Sink User Sink station Bandwidth

C MAC Shared NE1 C(1) NE5 10 Mbit/s

C MAC Shared NE1 C(2) NE5 10 Mbit/s


31/88




Configuring the MAC Shared EPL Service :

Step 1: Networking Diagram Step 2: Board Information of Each NE




32/88


T2000NE1

NE2

NE3

NE4 NE5A B

A BVC-Trunk

MAC1 MAC2

MAC1 MAC2

MAC3 MAC4

C(2)C(1)

C (Headquarters)

MAC3

C & C(1) Service

C & C(2) Service




33/88


VC4-4:VC12-1~VC12-5

MAC1A

10M

40M

B

VCTRUNKMAC

MAC2

VCTRUNK1

VCTRUNK2

VC-4-1:VC-3-1SDH

VC4-4:VC12-1~VC12-5

VCTRUNK

VCTRUNK1

VCTRUNK2

VC-4-1:VC-3-1

MAC1A

10M

40MB

MAC

MAC2

NE1 NE5

VCTRUNK3

VCTRUNK4

MAC3C1

10M

10M

C2MAC4

VC4-4:VC12-6~VC12-10

VC4-4:VC12-11~VC12-15

VCTRUNK3

VCTRUNK4

VC4-4:VC12-6~VC12-10

VC4-4:VC12-11~VC12-15

MAC3C




NE1 and NE5 do not require any new board.


34/88




Service Attribute C & C(1) C & C(2)

Source NE NE1

Source board - port 13-N1EFS4-3

Source timeslot VC4-4: VC12-6VC12-10 VC4-4: VC12-11VC12-15

Source VCTRUNK VCTRUNK3 (Tag aware) VCTRUNK4 (Tag aware)

Working mode of source MAC port Auto negotiation Auto negotiation

TAG flag of source MAC port Tag aware Tag aware


Bound bandwidth 5 x VC-12 5 x VC-12

Sink NE NE5


Sink timeslot VC4-4: VC12-6VC12-10 VC4-4: VC12-11VC12-15

Sink VCTRUNK VCTRUNK3 (Tag aware) VCTRUNK4 (Tag aware)





35/88


Timeslot


12-SL16-1

NE1

7-SL16-112-SL16-17-SL16-112-SL16-17-SL16-112-SL16-1 7-SL16-1

Forwared

NE5StationNE4

13-SL4-1 7-SL4-1

Ring

Chain

Add/Drop

VC-4-3 13-EFS4: VC4-4

VC-12: 6-15

VC-4-315-EFS4: VC4-4

VC-12: 6-15




36/88


Notice: We dont need the first step because the Ethernet boards

Have already been created.


Configuring the MAC Shared EPL Service:


Step 1: Creating a board (None)



Step 4: Creating the MAC shared EPL service

Step 5: Configuring committed access rate (CAR) (Optional




37/88


Configuring the EPL Service Step 2: Configuring Ethernet interfaces

Right click

Left click

Left click


38/88



Left click

Left click

Left click

Left click



39/88


Left click


Left click

Step 4: Creating the MAC shared EPL service


40/88


Notice: These two steps are the same as that of the

point-to-point EPL service, except that some

parameters are different.


Step 5: Configuring committed access rate (CAR) (Optional

Step 6: Configuring the cross-connect from Ethernet boards to

SDH line boards


41/88


Summary





Configuring binding paths:

Configurable Ports, Level, Direction, Available VC4, timeslots

Creating the MAC shared EPL service:






42/88








43/88



Configuring the VCTRUNK Shared EPL Service :





44/88



T2000

STM-4 two-fiber

bidirectional non- protection chainNE1

NE2

NE3

NE4

NE5



Configuring the VCTRUNK Shared EPL Service:

Source

User

Service

requirement

Source

station

Sink User Sink

station

Bandwidth

D VCTRUNK Shared NE2 D NE3 300 Mbit/s

E VCTRUNK Shared NE2 E NE3 300 Mbit/s


45/88



Configuring the VCTRUNK Shared EPL Service :







46/88


T2000

NE1

NE2

NE3

NE4

NE5

D

B

VC-Trunk

MAC1

MAC2

MAC2MAC1

E

D E D & D Service

E & E Service




47/88



Step 2: Board Information of Each NEBoard layout of NE2 and NE3


48/88


MAC1D300M

E

VCTRUNKMAC

MAC2

SDH

VC4-1:VC3-1~VC3-3

VC4-2:VC3-1~VC3-3

VCTRUNK

VCTRUNK1

MAC1 D

E

MAC

MAC2

NE2 NE3

300M

300M

300MVC4-1:VC3-1~VC3-3

VC4-2:VC3-1~VC3-3

VCTRUNK1




49/88




Service Attribute D E

Source NE NE2

Source board - port 13-N1EGS2-1 13-N1EGS2-2

Source timeslot VC4-1: VC3-1VC3-3, VC4-2: VC3-1VC3-3

Source VCTRUNK VCTRUNK1 (Tag aware)

Working mode of source MAC port 1000M full duplex 1000M full duplex

TAG flag of source MAC port Access Access


Bound bandwidth 6 x VC-3

Sink NE NE3

Sink board - port 13-N1EGS2-1 13-N1EGS2-2

Sink timeslot VC4-1: VC3-1VC3-3, VC4-2: VC3-1VC3-3

Sink VCTRUNK VCTRUNK1 (Tag aware)

Working mode of sink MAC port 1000M full duplex 1000M full duplex




50/88


Timeslot


12-SL16-1

NE1

7-SL16-112-SL16-1 7-SL16-1 12-SL16-1 7-SL16-1 12-SL16-1 7-SL16-1

Forward

Ring

Add/Drop

VC-4-313-EGS2: VC4-1

VC-3: 1-3

VC-4-413-EGS2: VC4-2

VC-3: 1-3




51/88


Notice: The steps are the same as the MAC shared EPL Service.

So here we dont need introduce them again.


Configuring the VCTRUNK Shared EPL Service:Configuration Process

Step 1:Creating a board



Step 4: Creating the VCTRUNK shared EPL service



SDH line boards


52/88


Summary






Configurable Ports, Level, Direction, Available VC4, timeslots Creating the VCTRUNK shared EPL service:




Configuring the cross-connect from Ethernet boards to SDH line

boards


53/88







54/88


Configuring the EPLAN Service

Configuring the EPLAN Service:





55/88



T2000STM-4 two-fiber

bidirectional non- protection chainNE1

NE2

NE3

NE4NE5



Source User Service requirement Source station Sink User Sink station Bandwidth

F(1) EPLAN NE2 F(2) NE3 10 Mbit/s




56/88









57/88


T2000

NE1

NE2

NE3

NE4

NE5

B

VC-Trunk

MAC1

MAC1

F(1)

F(2)

MAC1

F(3)

VB

MAC1

VCTRUNK1

MAC1

VCTRUNK2VCTRUNK1 VB

VB

MAC1

VCTRUNK1

F(1) & F(2) Service

F(3) & F(2) Service

F(1) & F(3) Service




58/88


Board layout of NE2 and NE3




59/88



Step 2: Board Information of Each NEBoard layout of NE4


60/88


Service configuration diagram

MAC1F2

10M

VCTRUNKMAC

SDH

VC4-4:VC12-1~VC12-5

VCTRUNK

VCTRUNK1

MAC1F1

MAC

NE3

NE2

10M

VC4-4:VC12-1~VC12-5VCTRUNK1

VB1

LP1 LP2

LP3

VCTRUNK2VC4-4:VC12-6~VC12-10

VB1

VC4-4:VC12-1~VC12-5

VCTRUNK

VCTRUNK1

MAC1F3

MAC

NE4

10M

VB1

LP1

LP1

LP2

LP2




61/88



Attribute \ Service F

Source NE NE3

Source board port 14-N1EFS0-1

Source timeslot VC4-4: VC12-1VC12-5 VC4-4: VC12-6VC12-10

Source VCTRUNK VCTRUNK1 (Tag Aware) VCTRUNK2 (Tag Aware)

Source VCTRUNK attribute PE PE

Working mode of source MAC port Auto negotiation

TAG flag of source MAC port Access

VLAN ID of source MAC port 11

VB VB1

Attached port MAC1, VCTRUNK1, VCTRUNK2

Sink NE NE2 NE4

Sink board port 14-N1EFS0-1 15-N1EFS0-1

Sink timeslot VC4-4: VC12-1VC12-5 VC4-4: VC12-1VC12-5

Sink VCTRUNK VCTRUNK1 (Tag Aware) VCTRUNK1 (Tag Aware)

Sink VCTRUNK attribute PE PE




Virtual bridge (VB) VB1 VB1

Attached port MAC1, VCTRUNK1 MAC1, VCTRUNK1


62/88





NE name VB VLAN ID Forwarding port

NE2 VB1 11 LP1, LP2

NE3 VB1 11 LP1, LP2, LP3

NE4 VB1 11 LP1, LP2

Timeslot


12-SL16-1

NE1

7-SL16-112-SL16-1 7-SL16-1 12-SL16-1 7-SL16-1 12-SL16-1 7-SL16-1

Forward

Ring

Add/Drop

VC-4-5 14-EFS0: VC4-4

VC-12: 1-5

15-EFS0: VC4-4

VC-12: 1-5


63/88







Step 4: Creating the EPLAN service

Step 5: Configuring the forwarding filter table



SDH line boards


64/88





65/88


Configuring the EPLAN Service Step 2: Configuring Ethernet interfaces

Right click

Left click

Left click


66/88


Left click


Left click

Left click

Left click

Step 3:

Configuring

binding paths


67/88


Left click

Configuring the EPLAN Service Step 4: Creating the EPLAN service

Left click

Left click

Left click

Left click


68/88


Configuring the EPLAN Service Step 5: Configuring the forwarding filter table

Left click

Left click

Left click


69/88


Configuring the EPLAN Service Step 6: Configuring committed access rate (CAR) (Optional )

Left click

Left click


70/88


Configuring the EPLAN Service Step 7: Configuring the cross-connect from Ethernet boards to SDH line

boards

Left click

Left clickLeft click


71/88


Summary



External Port: Basic Attributes, Tag Attribute, VLAN

Internal Port: Tag Attribute, VLAN, LCAS


Configurable Ports, Level, Direction, Available VC4, timeslots Creating the EPLAN service:

VB Port, Mount Port, Port Type, Binding Path

Configuring the forwarding filter table

VB Port, VLAN ID, forwarding port





72/88







73/88


Configuring the EVPL Service

Configuring the EVPL Service:





74/88



T2000 STM-4 two-fiber

bidirectional non-protection chainNE1

NE2

NE3

NE4NE5



Source

User

Service

requirement

Source

stationSink User

Sink

stationBandwidth

D EVPL NE2 D NE3 100 Mbit/s

E EVPL NE2 E NE3 100 Mbit/s


75/88










76/88


T2000

NE1

NE2

NE3

NE4

NE5

D

B

VC-Trunk

MAC1

MAC2

MAC2MAC1

E

D ED & D Service

E & E Service

g g



77/88


Configuring the EVPL Service Step 2: Board Information of Each NE

Board layout of NE2 and NE3


78/88





79/88




Attribute \ Service D ESource NE NE2

Source board - port 14-N1EFS0-1 14-N1EFS0-2

Source timeslot VC4-4: VC12-1VC12-48

Source VCTRUNK VCTRUNK1 (Tag Aware )

Source VCTRUNK attribute PWorking mode of source MAC port 100M full duplex 100M full duplex

TAG flag of source MAC port Tag Aware Tag Aware


Source MAC attribute PE PE

Bound bandwidth 48 x VC-12

Sink NE NE3


Sink timeslot VC4-4: VC12-1VC12-48

Sink VCTRUNK VCTRUNK1 (Tag Aware )Sink VCTRUNK attribute P

Working mode of sink MAC port 100M full duplex 100M full duplex

TAG flag of sink MAC port Tag Aware Tag Aware


Sink MAC attribute PE PE


80/88





NE nameVCTRUNK-MAC

(path)

multi-protocol label switching (MPLS)

Tunnel VC

NE2 \ NE3 VCTRUNK1-MAC1 55 25

NE2 \ NE3 VCTRUNK1-MAC2 66 26

Station

Timeslot

NE1 NE2 NE3 NE4 NE1

12-SL16-1 7-SL16-1 12-SL16-1 7-SL16-1 12-SL16-1 7-SL16-1 12-SL16-1 7-SL16-1

VC4-4

VC12: 1-48

14EFS0: VC4-4

Forward

Add/Drop


81/88







Step 4: Creating the EVPL service


(Optional )




82/88





83/88


Configuring the EVPL Service Step 2: Configuring Ethernet interfaces

Right click

Left click

Left click


84/88


Configuring the EVPL Service Step 3: Configuring binding paths

Left click

Left click

Left click

Left click


85/88



Step 4: Creating the

EVPL service

Left clickLeft click Left click



86/88


Notice: These two steps are the same as that of the EPL service,

except that some parameters are different.



(Optional )




87/88


Summary



External Port: Basic Attributes, Tag Attribute, VLAN

Internal Port: Tag Attribute, VLAN, LCAS, MPLS


Configurable Ports, Level, Direction, Available VC4, timeslots

Creating the EVPL service:

Service Type, Service Direction, Ports, TAG, VLAN, Tunnel, VC,

Port Type, Encapsulation Format



Configuring the cross-connect from Ethernet boards to SDH line

boards


88/88

www.huawei.com

Thank You

Documents

19-OTA105204 OptiX OSN Ethernet Services Configuration(Manual Configuration) ISSUE 1.21