18V CordlessChain Saw

Item # 143396

WARNING:Read and understand RULES FOR SAFE OPERATION

and instructions carefully before operating.

Failure to follow the safety rules and other basic safety

precautions may result in serious personal injury.

INSTRUCTION MANUAL

SPECIFICATIONS:Chain speed: 465 FPM; Length of guide bar: 8-5/16in.; Saw chain type: 25 AP;Saw chain pitch: 1/4in.; Saw chain No. of drive links: 42

IMPORTANT SAFETY INSTRUCTIONSWARNING: WHEN USING A CORDLESS CHAIN SAW, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO

PERSONS, INCLUDING THE RISK OF FIRE, ELECTRIC SHOCK, AND INJURY TO PERSONS, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS.1. Keep Work Area Clean

Cluttered areas invite injuries. Do not start cutting until you have a clear work area,secure footing, and a planned retreat path from the falling tree.

2. Consider Work Area EnvironmentUse extreme caution when cutting small size brush and saplings because the slendermaterial may catch the saw chain and be whipped toward you or pull you off balance. Donot operate a chain saw in a tree unless specifically trained to do so. When cutting a limbthat is under tension be alert for spring back so that you will not be struck when the tensionin the wood fibers is released. Don't expose chain saw to rain. Don't use chain saw indamp or wet locations. Do not use chain saw in presence of flammable liquids or gases.

3. Guard Against Electric ShockPrevent body contact with grounded surfaces. For example: metal pipes, wire fences.

4. Keep Children AwayDo not let visitors contact chain saw. All visitors should be kept away from work area.

5. Store Idle Chain SawWhen not in use, chain saws should be stored in a dry, and high or locked-up place. Keep out of the reach of children. When storing saw, use a scabbard or carrying case.

6. Don't Force Chain SawIt will do the job better and safer at the rate for which it was intended.

Item No. Description1 Right cover, chain2 Inner gear3 Star gear4 Shaft5 Bearing6 Plate7 Screw, ST8 Washer9 Sprocket

10 Washer, bore11 Locking ring12 Left cover, chain13 Screw14 Guide Bar, chain15 Chain16 Washer17 Spring washer18 Bolt19 Front hand guard20 Screw, left case21 Case, left

Item No. Description22 Rubber cover23 Cover, motor24 Relief25 Spring26 Wire27 Support, motor28 Motor & gear assy29 Button, switch30 Case, right31 Hex Key32 Battery33 Connector, body to battery34 Switch35 Safety switch36 Spring, safety37 Cover, inner38 Screw39 Big washer40 Star gear41 Plate, gear inner

3635

34

33

4140

39

38

37

24

25

28

2930

2627

3132

20

19

21

23

22

910

1112

18

76

54

32

13

14

1516

1718

10

Thank you very much for choosing a Wel-Bilt TM product! For future reference,please complete the owner's record below:

Model: _______________ Purchase Date: _______________

Save the receipt, warranty and these instructions. It is important that you readthe entire manual to become familiar with this product before you begin using it.

This machine is designed for certain applications only. The distributor cannotbe responsible for issues arising from modification. We strongly recommendthis machine is not modified and/or used for any application other than that forwhich it was designed. If you have any questions relative to a particular application,DO NOT use the machine until you have first contacted the distributor todetermine if it can or should be performed on the product.

For technical questions please call 1-800-222-5381.

1

Cleaning guide barChips and sawdust will build up in the guide bar groove,clogging it and impairing oil flow. Always clean out the

chips and sawdust when sharpening or replacing thesaw chain.

Storing machineClean the machine before storing. Remove any chips and sawdust from the machine afterremoving the chain cover. After cleaning the machine, run it under no load. Then remove the

battery cartridge from the machine and lubricate the saw chain and guide bar.

9 2

12. Disconnect Chain SawDisconnect battery cartridge from chain saw when not in use, before servicing, and whenchanging accessories and attachments, such as saw chain and guard.

13. Stay AlertWatch what you are doing. Use common sense. Do not operate chain saw when you aretired. Keep all parts of the body away from the saw chain when the motor is operating.Before you start the saw, make sure the saw chain is not in contact with anything.

14. Check Damaged PartsBefore further use of the chain saw, a guard or other part that is damaged should becarefully checked to determine that it will operate properly and perform its intended function.Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting,and any other conditions that may affect its operation. A guard or other part that is damagedshould be properly repaired or replaced by an authorized service center unless otherwiseindicated elsewhere in this instruction manual. Have defective switches replaced byauthorized service center. Do not use chain saw if switch does not turn it on and off.Do not operate a chain saw that is damaged, improperly adjusted, or is not completely andsecurely assembled. Be sure that the saw chain stops moving when the trigger is released.

15. Guard Against Kickback WARNING: KICKBACK may occur when the nose or tip of the guide bar touchesan object, or when the wood closes in and pinches the saw chain in the cut. Tip contactin some cases may cause a lightning fast reverse reaction, kicking the guide bar upand back towards the operator. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to lose control of the saw which could result in serious injury to user. The following precautions should be followed to minimize kickback.(1) Grip saw firmly. Hold the chain saw firmly with both hands when the motor is running. Use a firm grip with thumbs and fingers encircling the chain saw handles.

Hex wrench

Saw chain

Guide bar complete

Scabbard

Guide bar

Screwdriver

File

Battery cover

7. Use Right ToolCut wood only. Don't use chain saw for purpose not intended - for example- Don’t use chain saw for cutting plastic, masonry or non-wood building materials.

8. Dress ProperlyDo not wear loose clothing or jewelry. They can get caught in moving parts. Workgloves and non-skid footwear are recommended when working outdoors. Wear protectivehair covering to contain long hair.

9. Use Safety GlassesUse safety goggles or safety glasses with side shields which comply with current nationalstandards, or when needed, a face shield.

10. Carrying SawCarry the chain saw with the saw stopped, finger off the switch, the guide bar and sawchain to the rear.

11. Maintain Chain Saw With CareKeep tools sharp and clean for better and safer performance. Follow instructions for lubricatingand changing accessories. Keep handles dry, clean, and free from oil and grease.

3

IMPORTANT SAFETY INSTRUCTIONSFOR CHARGER & BATTERY CARTRIDGE

1. Save these instructions.2. Before using battery charger, read all instructions and cautionary markings on battery charger, battery and product using battery.3. CAUTION: To reduce risk of injury, charge only Wel-Bilt Battery Cartridge. Other types of batteries may burst causing personal injury and damage.4. Do not expose charger to rain or snow.5. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons.6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.7. Make sure cord is located so that it will not be stepped on, or tripped over. Otherwise it will be subject to damage or stress.8. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock.9. Do not operate charger with damaged cord or plug - replace them immediately.10.Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman.11.Do not disassemble charger or battery cartridge; take it to a qualified serviceman when

service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.12.To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk.

FOR CHARGER & BATTERY CARTRIDGE1. Do not charge Battery Cartridge when temperature is BELOW 50°F (10°C) or ABOVE 104°F (40°C ).2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle.3. Do not allow anything to cover or clog the charger vents.4. Always cover the battery terminals with the battery cover when the battery cartridge is not used.5. A battery short can cause a large current flow, overheating, possible burns and even a breakdown.

(1) Do not touch the terminals with any conductive material.

MAINTENANCECAUTION:

• Always be sure that the machine is switched off and the battery cartridge is removedbefore carrying out any work on the machine.

• Always wear gloves when performing any inspection or maintenance.

Filing saw chainFile the saw chain so that the cutters meet the specifications indicated in illustration.

1) Filing cuttersUse a round file 4 mm in outer diameter to file the cutters. Apply it to the cutter so thatit will be angled 30° to the guide bar and protrude 1/5 of the outer diameter from the tipof the cutter. Hold the file level and push it away from you while filing. Be careful not to touch the cutters with the file when pulling it back toward you.

2) Filing depth gaugesUse a flat file to file the depth gauges. Hold the file level while filing.Round off the front corner of the depth gauge to maintain its original shape.

After filing the saw chain, immerse it in oil and wash off filing chips and sawdust fromthe saw chain.

8

(2) Do not over reach.(3) Keep proper footing and balance at all times.(4) Don't let the nose of the guide bar contact a log, branch, ground. or other obstruction.(5) Don’t cut above shoulder height.(6) Use devices such as special guide bars that reduce the risks associated with kickback.(7) Only use replacement bars and chains specified by the manufacturer.

16. Replacement Parts When servicing use only identical replacement parts.17. Before making a felling cut, remove dirt, stones, loose bark, nails, staples and wire from the tree.18. Secure the log so that it will not roll or move suddenly during operation.19. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is in OFF position before inserting battery cartridge.20. The chain saw must not be left outdoors during rain and it must not be used when wet.

Chain Saw Parts Diagram(1) Front handle(2) Front handle guard(3) Spike bar(4) Fastening bolt(5) Sprocket guard(6) Bar tip guard(7) Battery cartridge(8) Guide bar(9) Lock - off button(10) Rear handle(11) Switch trigger(12) Saw chain(13) Oil bottle

Installing or removing battery cartridge• Always switch off the tool before insertion or

removal of the battery cartridge.

• To remove the battery cartridge, withdrawit from the tool while pressing the buttons onboth sides of the cartridge.

• To insert the battery cartridge, align the tongueon the battery cartridge with the groove in thehousing and slip it into place. Always insert itall the way until it locks in place with a little click.If not, it may accidentally fall out of the tool,causing injury to you or someone around you.

• Do not use force when inserting the battery cartridge. If the cartridge does not slide ineasily, it is not being inserted correctly.

Charging

• Your new battery cartridge is not charged. You will need to charge it before use. Use thehigh capacity battery charger to charge the battery cartridge.

• Plug the high capacity battery charger into the proper A.C. voltage source. The charginglight will turn to red.

• Insert the battery cartridge so that the plus and minus terminals on the battery cartridgeare on the same sides as their respective markings on the high capacity battery charger.Insert the cartridge fully into the port so that it rests on the charger port floor.

When cutting thick branches first make a shallow undercut and then make the finish cut fromthe top.

If you try to cut off thick branches from the bottom, the branch may close in and pinch the sawchain in the cut.

If you try to cut off thick branches from the top without a shallow undercut, the branch maysplinter.

If you cannot cut the timber right throughwith a single stroke: Apply light pressureto the handle and continue sawing and drawthe chain saw back a little; then apply thespike a little lower and finish the cut by raisingthe handle.

Adjusting saw chain tensionThe saw chain may become loose after many hours of use. From time to time check the sawchain tension before use. Grasp the saw chain in the middle of the guide bar and lift up. Thegap between the guide bar and the tie strap of the saw chain should be approx. 2 - 3 mm(5/64in. - 7/64in.). If the gap is not approx. 2 - 3 mm (5/24in.-7/64in.), slightly loosen the hexsocket head bolt which secures the guide bar. The gap will be automatically adjusted to approx.

2-3 mm (5/64in.-7/64in.) by the saw chain tension adjusting spring. Then tighten the hexsocket head bolt securely after making sure that the gap is approx. 2 - 3 mm (5/64in.- 7/64in.).

7 4

6. Do not store the tool and Battery Cartridge in locations where the temperature may reach or exceed 122°F (50°C).7. Do not incinerate the Battery Cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.

(2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.(3) Do not expose battery cartridge to water or rain.

5 6

• Charging time is approximately 3 hours.

• After charging, unplug the charger from the power source.

CAUTION:• When you charge a new battery cartridge or a battery cartridge which has not been used

for a long period of time, it may not accept a full charge. This is a normal condition anddoes not indicate a problem. You can recharge the battery cartridge fully after dischargingit completely and recharging a couple of times.

• If you wish to charge two battery cartridges, allow 15 minutes between charging on thehigh capacity battery charger.

Installing or removing saw chainCAUTION:

• Always be sure that the tool is switched off and the battery cartridge is removed beforeinstalling or removing the saw chain.

• Always wear gloves when installing or removing the saw chain.

• Use only saw chain and guide bar with bar tip designed for this chain saw (see theextract from the spare parts list).

• ln order to prevent kickback, do not remove the bar tip or replace the guide bar with onewithout a bar tip.

Loosen the screws with a screwdriver. Remove the sprocket guard.Loosen the hex socket head bolt with the hex wrench provided. Remove the guide bar.

Fit the saw chain over the guide bar.Notice that the cutters must be facingthe revolving (arrow) direction.

Fit the saw chain over the sprocket. Install the guide barso that its concave protion will contact the saw chaintension adjusting spring.Tighten the bolt to secure the guide bar. Install the sprocketguard and tighten the screws to secure it.

LubricationCAUTION:

• Always be sure that the tool is switched off and thebattery cartridge is removed before lubricating the sawchain.

• Always use vegetable oil when pruning fruit trees.Mineral oil may harm trees.

Lubricate the whole saw chain evenly before each use.Also lubricate it whenever replacing a fully dischargedbattery cartridge with a charged one.

Switch actionCAUTION:

Before inserting the battery cartridge into the machine,always check to see that the switch trigger actuatesproperly and returns to the “OFF” position when released.

To prevent the switch trigger from being accidentally pulled,a lock-off button is provided.

To start the machine, depress the lock-off button and pullthe switch trigger. Release the switch trigger to stop.

Carrying machineAlways remove the battery cartridge from the machineand cover the guide bar with the scabbard before carryingthe machine. Also cover the battery cartridge with thebattery cover.

Pruning treesCAUTION:

• Keep all parts of the body away from the saw chain when the motor is operating.

• Hold the chain saw firmly with both hands when the motor is running.

• Do not overeach. Keep proper footing and balance at all times.

Bring the tip guide/lower guide into contact with the branch to be cut before switching on.Cutting without bringing the tip guide/lower guide into contact with the branch may cause theguide bar to wobble, resulting in injury to operator.

12-month12-MONTH REPLACEMENT WARRANTY