Upload
migara-perera
View
76
Download
12
Embed Size (px)
Citation preview
16-009 Supa Hand Sand Line PARTS CATALOG
VT INDUSTRIES
Designed by Migara Perera
2
Contents 1.0 16-009 Machine Foot Print ............................................................................................................................................... 3
2.0 Machine Assembly Prints .................................................................................................................................................. 4
2.1 Door Flipper ................................................................................................................................................................. 4
2.1.1 Flipper Barrel Assembly ........................................................................................................................................ 5
2.1.2 Valve & Valve Base ................................................................................................................................................. 6
2.2 Centering Table ............................................................................................................................................................ 7
2.2.1 Left Pusher Assembly ............................................................................................................................................. 8
2.2.2 Right Pusher Assembly ........................................................................................................................................... 9
2.2.3 Pop Up Assembly ................................................................................................................................................. 10
2.3 Infeed Table ................................................................................................................................................................ 11
2.4 Infeed Lift .................................................................................................................................................................... 12
2.4.1 Vertical Lift Assembly ........................................................................................................................................... 13
2.4.2 Horizontal Carriage Assembly .............................................................................................................................. 14
2.4.3 Wheel Assembly ................................................................................................................................................... 15
2.4.4 Traverse Assembly ............................................................................................................................................... 16
2.4.5 Lift Assembly ........................................................................................................................................................ 17
2.4.6 Spring Block Assembly ......................................................................................................................................... 18
2.4.7 Traverse Vertical Assembly .................................................................................................................................. 19
2.5 Inspection Table .......................................................................................................................................................... 20
2.6 Out feed Lift ................................................................................................................................................................ 22
2.6.1 Traverse Assembly ............................................................................................................................................... 23
2.6.2 Horizontal Carriage Assembly .............................................................................................................................. 24
2.6.3 Wheel Assembly ................................................................................................................................................... 25
2.6.4 Traverse Assembly ............................................................................................................................................... 26
2.6.5 Lift Assembly ........................................................................................................................................................ 27
2.6.6 Spring Block Assembly ......................................................................................................................................... 28
2.6.7 Vertical Traverse Assembly .................................................................................................................................. 29
3.0 Purchase Parts ................................................................................................................................................................. 30
4.0 Recommend Spare Parts ................................................................................................................................................. 34
5.0 P.M Schedule .................................................................................................................................................................. 35
6.0 Index ................................................................................................................................................................................ 41
6.1 Contact Information .................................................................................................................................................... 41
3
1.0 16-009 Machine Foot Print
2.0 Machine Assembly Prints
2.1 Door Flipper
5
2.1.1 Flipper Barrel Assembly
6
2.1.2 Valve & Valve Base
7
2.2 Centering Table
8
2.2.1 Left Pusher Assembly
9
2.2.2 Right Pusher Assembly
10
2.2.3 Pop Up Assembly
11
2.3 Infeed Table
12
2.4 Infeed Lift
13
2.4.1 Vertical Lift Assembly
14
2.4.2 Horizontal Carriage Assembly
15
2.4.3 Wheel Assembly
16
2.4.4 Traverse Assembly
17
2.4.5 Lift Assembly
18
2.4.6 Spring Block Assembly
19
2.4.7 Traverse Vertical Assembly
20
2.5 Inspection Table
21
2.5.1 Pop Up Cylinder Assembly
22
2.6 Out feed Lift
23
2.6.1 Traverse Assembly
24
2.6.2 Horizontal Carriage Assembly
25
2.6.3 Wheel Assembly
26
2.6.4 Traverse Assembly
27
2.6.5 Lift Assembly
28
2.6.6 Spring Block Assembly
29
2.6.7 Vertical Traverse Assembly
3.0 Purchase Parts
Vendor PO# Part # Description
Quantity
(Total) Add. Info
Applied Industrial
82817 MCT 10500-65-24-KWEE Drive and Idler Casters 4 Door Flipper
Applied Industrial
82817 ALBI PIXS-0420112 Side Support Casters 5 Door Flipper
Applied Industrial
82817 BROW VF2S-224 2 Bolt Flange Bearing x 1-1/2 8 Door Flipper
Van Meter 8282
8 R57DRE100L4BE5HR Spinner Drive per quote #20151223-
00065 1 Door Flipper
Van Meter 8282
8 S47DRE80M4 Roller Drive per quote #20151223-
00076 full oil, no breather 1 Door Flipper
Applied Industrial
82817 BROW VF2S-232 2 Bolt Flange Bearing x 2 1 Door Flipper
Braas 8282
4 VS7-8-FG-D-1M Valve 1 Door Flipper
Braas 8282
4 VS7-2-A04T Valve Base 1 Door Flipper
Braas 8282
4 AC40BN04-G-V1-Z 1/2" Port Regulator/Filter 1 Door Flipper
Hartfiel Automation
82818
TA-MP2-6x5.25-MPR-OP=1 & 5 Clamping Cylinder 1 Door Flipper
Hartfiel Automation
82818 RS01AC-SB590 Reed Switch 1 Door Flipper
McMaster Carr 8282
2 8702K85 1/2x2x60 Polyethylene (by foot) 30 Door Flipper
Applied Industrial
82817 MART 40BS16x1 Tube Roller Drive Sprocket 1 Door Flipper
Applied Industrial
82817 MART 80TB25 Spinner Drive Sprockets 2 Door Flipper
Applied Industrial
82817 DODG 2517x2KW Spinner Drive Taperlock 1 Door Flipper
Applied Industrial
82817 DODG 2517x1-3/8KW Spinner Drive Taperlock 1 Door Flipper
Van Meter 8283
9 UCP205-216 1" Pillowblock Bearings 4 Door Flipper
Applied Industrial
82817 MCGI MR10 Needle Bearing for Clamping Device 4 Door Flipper
Applied Industrial
30110
NS-R2511-A6205-60.25-V42.
Tube Roller w/ one groove and 11/16 hex axle, 3/8 Groove , orange
Lagging 12
Outfeed Centering
Table
Applied Industrial
30110 VPS 216 Pillow Block Bearing 17 All Tables
Applied Industrial
30110 THK_SHS30 + 1340mm Bearing Rail - G1=G2=30mm 2
Outfeed Centering
Table
31
Applied Industrial
30110 THK_SHS30V1SS Bearing Block 4
Outfeed Centering
Table
Hartfiel Automation
30100
TAMS4-2X21.25-H2C6-OP=1&5-OS-1 Centering Fence Cylinder 1
Outfeed Centering
Table
Hartfiel Automation
30100
FM-MF2-2x1-KK1-MPR+(AC437) Pop up Cylinder+Coupler 16
Outfeed Centering / Inspection
Table
Hartfiel Automation
30100 TRD R10PQ-SB15 Reed Switch for 2in bore air cylinder 3
Outfeed Centering
Table
Applied Industrial
30110 40BB18H x 5/8 IDLER Centering Idler Sprocket 2
Outfeed Centering
Table
Van Meter 3019
0 SEW W30DRS71S4
1/2HP 16.33:1 (104-RPM) MTG.POS:M1; 3/4" SOLID
SHAFT OUTPUT SIDE-A; 20160203-000177 1
Outfeed Centering
Table
McMaster Carr 3013
1 8702K85 Impact Resistant UHMW Rectangular
Bar 1/2 x 2 x 4ft 1
Outfeed Centering
Table
McMaster Carr 3013
1 8702K86 Impact Resistant UHMW Rectangular
Bar 1/2 x 2 x 5ft 4
Outfeed Centering
Table
Applied Industrial
30110 MART 50BS15 X 3/4 Motor Drive Sprocket 3
Outfeed Centering /
Infeed / Inspection
Table
Applied Industrial
30110 MHS-SR25 P-05
2 1/2 X 1 1/8IN SFT RBR WHL-PL BORE 46
Outfeed Centering / Inspection
Table
Applied Industrial
30112
NS-R2511-A6205-60.25-V42.
Tube Roller w/ one groove and 11/16 hex axle, 3/8 Groove Orange lagging 12 Infeed Table
Applied Industrial
30112 UST 50BS15 X 1 Shaft Drive Sprocket 3
Outfeed Centering /
Infeed / Inspection
Table
Applied Industrial
30112 MART BK40 X 1 Sheave 36
Outfeed Centering /
Infeed / Inspection
Table
32
Van Meter 3012
5 WF47DRE100LC4BE5HR SEW Drive per SEW quote
#20160202-00046 2
Infeed / Outfeed Stacker
Schmalz 3012
3 STF 60 P 4.5 SSD Dust Filter 4
Infeed / Outfeed Stacker
Schmalz 3012
3 SBB-ST-VZ/ABS Silencer Box 4
Infeed / Outfeed Stacker
Igus 3016
1 15050-16-150 E4 SERIES ENERGY CHAIN 16 FEET 16 Infeed/Outfe
ed Stacker
Igus 3016
1 15050-18-150 E4 SERIES ENERGY CHAIN 24 FEET 24 Infeed/Outfe
ed Stacker
Van Meter 3012
5 HSR25A1SS Vertical Lift Tube THK Bearings 8 Infeed/Outfe
ed Stacker
Van Meter 3012
5 55HTD14M Traverse Drive Belt (10 meter length)
Infeed 1 Infeed/Outfe
ed Stacker
Van Meter 3012
5 HSR25 x 2320 Vertical Lift Tube THK Rails Standard
G Dimension 4 Infeed/Outfe
ed Stacker
Van Meter 3012
5 P275USX128" Verticle Lift Belt x 128" Long 2 Infeed/Outfe
ed Stacker
Van Meter 3012
5 KA77BDRE132M4BE11HR SEW Drive per SEW quote
#20160202-00044 2 Infeed/Outfe
ed Stacker
Van Meter 3012
5 T50P17H Vertical Drive Driver Sprocket 2 Infeed/Outfe
ed Stacker
Braas 3015
5 SY50M-27-1-WO-02N Single Valve Sub base 3
Infeed/Outfeed Stacker / Inspection
table
Braas 3015
5 SYS101-5UF1 Solenoid Valve 1
Infeed/Outfeed Stacker / Inspection
table
European Woodworking
30105 BK40424300 Aclathan Roller for Carriage 24
Infeed/Outfeed Stacker
Van Meter 3012
5 BK2/800/140/1.25PFN/1.2
5PFN Traverse Servo Coupler 2 Infeed/Outfe
ed Stacker
Van Meter 3012
5 P28-14M-55-HT Traverse Drive Pulleys 8 Infeed/Outfe
ed Stacker
Schmalz 3012
3 EMVP 50 24V-DC 3/2 NO Solenoid Valve 4 Infeed/Outfe
ed Stacker
Schmalz 3012
3 FMC-SW 1227.5 18 0.6
O10O10 F Large Area Vacuum Gripping System 10 Infeed/Outfe
ed Stacker
Skarda Equipment
30140 8020-4338 Corner Brackets 40
Infeed/Outfeed Stacker
33
Skarda Equipment
30140 8020-4351 5 Hole Corner Plates 16
Infeed/Outfeed Stacker
McMaster Carr 3014
2 3731K110 Flanged Sleeve Bearing for 3/4 Shaft 20 Infeed/Outfe
ed Stacker
McMaster Carr 3014
2 9657K253 1.015OD Spring .120" wire diam.
2.56"long (pack of 6 3 Infeed/Outfe
ed Stacker
McMaster Carr 3014
2 91598A486 1/4 x 1-1/2 Coil Pins (pkg. 25) 1 Infeed/Outfe
ed Stacker
Van Meter 3012
5 Q1 x 2" Creative Pully Bushing 4 Infeed/Outfe
ed Stacker
Applied Industrial
30125 T50Q30H Vertical Drive Driven Sprocket 2
Infeed/Outfeed Stacker
Applied Industrial
30135
NS-R2511-A6205-41.875-V42.
Tube Roller w/ one groove and 11/16 hex axle, 3/8 Groove , orange
Lagging 24 Inspection
Table
Van Meter 3014
7 SEW W30DRS71S4
1/2HP 16.33:1 (104-RPM) MTG.POS:M1; 3/4" SOLID
SHAFT OUTPUT SIDE-A; 20160203-000177 1
Inspection Table
Van Meter 3012
5 UCPA210-31A 1-15/16" Vertical Drive Conveyor
Tapped Base Bearings 8 Infeed/Outfeed Stackers
34
4.0 Recommend Spare Parts
Stock
Quantity
Part Name Part Number Vendor Machine Used
2 THK Bearings HSR25A Applied Ind. Centering Table /
Stackers
4 European Woodworking
Wheels
BK40424300 European
Woodworking
Infeed Stacker/Outfeed
Stacker
1 Solenoid Valves SYS101-5UF1 Braas Infeed/Outfeed Stacker /
Inspection table
6 Vac Filter Elements STF60P4.5SSD Schmalz Stackers
2 Vertical Lift Belt P275US x 128” Van Meter Stackers
1 Cross Transfer Belt 55HTD14M x
13Meter Long
Van Meter Stackers
5 Gripper Foam 10.01.21.00201 Schmalz Stackers
5 Retro Reflective Photo
Switch
42EF-P8KBC-F4 Van Meter All Machines
5 Transmitted Beam 42EF-E8EZB-F4 Van Meter All Machines
5 Transmitted Beam
Receiver
42EF-R7KBB-F4 Van Meter All Machines
4 Allen Bradley Trojan T15
Safety Gate Switches
440K-T11267 Van Meter Flipper/ Outfeed Stacker
1 Travers Ball Bearings Emerson_VF4S-128 Applied Ind. Stackers
1 Vertical Lift Ball
Bearings
VTBS-231 Applied Ind. Stackers
1 Drive Ball Bearings VPS-216 Applied Ind. All Tables
1 box 5/16 Eagle Belting 1032010 Applied Ind. All Tables
1 box Triple 50 Chain - 10’
Lengths
B-L 50-3RX10FT Van Meter Stackers
35
5.0 P.M Schedule
PPS Line Bi-Weekly Preventative Maintenance ***NOTE: Follow Company Lockout/Tagout Procedures at all times. To lockout the infeed, turn off the main disconnect for the infeed. ***NOTE: Vacuum out all electrical panels on 03/01 and 9/01 of each year. Use a grounded vacuum. The date to vacuum the panels will not always fall on the exact day this PM prints. Vacuum on the closest date to the above date that this PM prints. ***NOTE: Change the oil in all gearboxes on 07/01 of each year. (Use Mobil 1 75W90) The date to change the oil will not always fall on the exact day this PM prints. Change the oil on the closest date to the above date that this PM prints. INFEED VACUUM PUMPS: ___ Visually inspect and listen for any noticeable signs of damage or wear. ___ Blow all dust and debris from unit. ___ Visually inspect all cables, wiring, and conduit for damage and/or proper routing. ___ Visually inspect Air Lines for Leaks, Worn Hoses, and Loose Fittings. (i.e. Locknuts on Flow Controls). Listen for leaks. ___ Check the hose that goes from the pump to the gate switch for heat stress and/or damage. ___ Check the hose that goes from the gate switch to the lift for heat stress and/or damage. ___ Clan and inspect filter. Replace if necessary! ___ Check mounting bolts for tightness and any other noticeable signs of damage or wear. ___ Reinstall muffler assembly. INFEED PORTAL: ___ Visually inspect Air Lines for Leaks, Worn Hoses, and Loose Fittings. (i.e. Locknuts on Flow Controls). Listen for leaks. ___ Visually inspect all cables, wiring, conduit, and wire trays for damage and/or proper routing. ___ Inspect all suction cups on the lift for wear and/or damage. ___ Visually inspect vertical lift belt for wear and/or damage. ___ Visually inspect traverse guide wheels for wear and/or damage. ___ Visually inspect guide ways for any damage. ___ Visually inspect vertical guide linear bearings for wear and/or damage. ___ Visually inspect vertical guide ways for any damage. ___ Check air regulator operating pressure. Pressure should be 80 psi or greater. (Located on West Side of Portal Frame) ___ Inspect regulator for wear and/or damage. ___ Inspect gearboxes (2) for obvious leaks and/or damage. ___ Change oil in gearboxes (2) on 07/01 of each year. (Vertical Lift Drive Use Shell Omala S2 6 220 Mineral oil) (Traverse Drive Use Kluber Synthetic SEW HT-460-5)
*** NOTE: The date to change the oil will not always fall on the exact day this PM prints. Change the oil on the closest date to the above date that this PM prints.
___ Lubricate all grease zerks. (Use Chevron ULTI-PLEX Synthetic EP grease: 1/2 pump per zerk) ___ Inspect all chains and sprockets for wear and/or damage. Clean and lubricate. Tighten if necessary! ___ Inspect all limit switches (0), photo-eyes (1), light barriers (0), proximity switches (9), Ultrasonic Sensors (0), Mag Door Switches (0), and reflectors (0) for proper alignment, damage, and tightness. Wipe lenses with a clean, soft cloth. Remove all dirt and debris. ___ Inspect e-stops(0)for damage.
36
INFEED PORTAL (cont’d): ___ Inspect fencing around portal area for damage. ___ Insure all guards are in good condition and in place. INFEED PORTAL POWERED CDLR ROLLERBED (2): ___ Observe rollerbed while running for proper operation. ___ Inspect overall condition of the rollers. ___ Visually inspect all cables, wiring, and conduit for damage and/or proper routing. ___ Inspect all chains and sprockets for wear and/or damage. Clean and lubricate. Tighten if necessary! ___ Inspect gearboxes (1) for obvious leaks or damage. ___ Change oil in gearboxes (1) on 07/01 of each year. (Use Mobil 1 75W90)
*** NOTE: The date to change the oil will not always fall on the exact day this PM prints. Change the oil on the closest date to the above date that this PM prints.
___ Lubricate all grease zerks. (Use Chevron ULTI-PLEX Synthetic EP grease: 1/2 pump per zerk) ___ Insure all guards are in good condition and in place. ___ Inspect all limit switches (0), photo-eyes (5), light barriers (0), proximity switches (0), Ultrasonic Sensors (0), Mag Door Switches (0), and reflectors (4) for proper alignment, damage, and tightness. Wipe lenses with a clean, soft cloth. Remove all dirt and debris. INFEED PORTAL CONVEYOR TABLE: ___ Visually inspect Air Lines for Leaks, Worn Hoses, and Loose Fittings. (i.e. Locknuts on Flow Controls). Listen for leaks. ___ Visually inspect all cables, wiring, and conduit for damage and/or proper routing. . ___ Observe conveyor while running for proper operation. ___ Inspect Eagle Belting drive belts. Repair or replace as necessary. ___ Inspect overall condition of the rollers. ___ Inspect conveyor rollers for bad bearings. Grasp and move each roller to inspect. ___ Lubricate all grease zerks (?). (Use EP2 Grease: 1/2 pump per zerk) ___ Inspect drive motor and chain. Tension chain as necessary w/1/2" Deflection. ___ Check gearbox for leaks (1). ___ Gearbox is lubed for life. Should be good unless leaking. (If it needs changed use Kluber Synthetic HT-460-5) ___ Insure all guards are in good condition and in place. ___ Inspect all limit switches (0), photo-eyes (4), light barriers (0), proximity switches (0), Ultrasonic Sensors (0), Mag Door Switches (0), and reflectors (0) for proper alignment, damage, and tightness. Wipe lenses with a clean, soft cloth. Remove all dirt and debris. INSPECTION/CONVEYOR TABLE (South): ___ Check that all inspection lights are working properly. Replace any bad or damaged lights. ___ Observe conveyor while running for proper operation. ___ Visually inspect Air Lines for Leaks, Worn Hoses, and Loose Fittings. (i.e. Locknuts on Flow Controls). Listen for leaks. ___ Visually inspect all cables, wiring, conduit, and wire trays for damage and/or proper routing.
37
INSPECTION/CONVEYOR TABLE (South) (cont’d): ___ Inspect all limit switches (0), photo-eyes (2), light barriers (0), proximity switches (0), Ultrasonic Sensors (0), Mag Door Switches (0), and reflectors (2) for proper alignment, damage, and tightness. Wipe lenses with a clean, soft cloth. Remove all dirt and debris. ___ Inspect overall condition of the conveyor rollers. ___ Inspect conveyor rollers for bad bearings. Grasp and move each roller to inspect. ___ Inspect all limit switches (0), photo-eyes (0), light barriers (0), proximity switches (0), Ultrasonic Sensors (0), Mag Door Switches (0), and reflectors (0) for proper alignment, damage, and tightness. Wipe lenses with a clean, soft cloth. Remove all dirt and debris. ___ Inspect condition of the eagle drive belts for the conveyor rollers. Replace as necessary and make sure there are 2 extra belts for each roller. ___ Check Pop-Up Rollers for wear and or damage. Replace as necessary! ___ Check Pop_Up Roller Cylinders (2) for proper operation, leaks, etc. ___ Inspect drive motor and chain. Tension chain as necessary w/1/2" Deflection. ___ Check gearbox for leaks (1). ___ Gearbox is lubed for life. Should be good unless leaking. (If it needs changed use Kluber Synthetic HT-460-5) ___ Insure all guards are in good condition and in place. ___ Inspect e-stop on Operator station for damage/function. ___ Inspect all limit switches (0), photo-eyes (4), light barriers (0), proximity switches (0), Ultrasonic Sensors (0), Mag Door Switches (0), and reflectors (0) for proper alignment, damage, and tightness. Wipe lenses with a clean, soft cloth. Remove all dirt and debris. ELECTRICAL CABINETS: ___ Blow all dust and debis from cooling fins on the cabinet. ___ Check the output air temperature of the A/C Unit. ___ Vacuum any dust and debris from the inside of the cabinet.
***NOTE: Use a grounded vacuum. ___ Check tightness of all electrical terminals and lugs in the cabinet.
*** NOTE: Be sure power is OFF when doing this. ___ Inspect lighted buttons for burnt out light bulbs.
*** NOTE: 1 E-Stop Button Lit when not depressed. FLIPPER: ___ Blow all dust and debris from table, including cooling fans on motors. ___ Inspect all Limit Switches, Light Barriers, Photoeyes, Proximity Switches, and reflectors:
1.) Check that they are securely mounted and aligned. 2.) Always keep free of dust and debris. Wipe lenses with soft cloth. 3.) Look for any wires or cables that may be pulled out or becoming frayed. 4.) Check that all actuating arms and rollers are in good order.
___ Clean and inspect all electrical connections and fittings. ___ Check all pneumatic connections damage and/or wear on hoses and fittings. ___ Clean, inspect, and lubricate roller drive chain. Re-tension if necessary. ___ Clean, inspect, and lubricate flipper drive and traverse chains. Re-tension as needed. ___ Lubricate flange bearings on flipper drive shaft with 2 shots of EP2 grease. ___ Check fluid level of flipper rotating drive gearbox. Top with Shell Omala S2 G 220 mineral oil. ___ Change the fluid in the flipper roller drive gearbox. Top with Shell Omala S2 G 680 mineral oil.
*** NOTE: Must be completely full!!. ___ Inspect condition of gripper material on flipper clamps. Replace as needed.
38
FLIPPER (cont’d): ___ Inspect safety fence for damage. Inspect East and West Safety gates for proper operation of safety switch and locking handle. ___ Inspect all limit switches (0), photo-eyes (11), light barriers (0), proximity switches (6), Ultrasonic Sensors (0), Mag Door Switches (0), and reflectors (0) for proper alignment, damage, and tightness. Wipe lenses with a clean, soft cloth. Remove all dirt and debris. INSPECTION/CONVEYOR TABLE (North): ___ Check that all inspection lights are working properly. Replace any bad or damaged lights. ___ Observe conveyor while running for proper operation. ___ Visually inspect Air Lines for Leaks, Worn Hoses, and Loose Fittings. (i.e. Locknuts on Flow Controls). Listen for leaks. ___ Visually inspect all cables, wiring, conduit, and wire trays for damage and/or proper routing. ___ Inspect all limit switches (0), photo-eyes (4), light barriers (0), proximity switches (0), Ultrasonic Sensors (0), Mag Door Switches (0), and reflectors (0) for proper alignment, damage, and tightness. Wipe lenses with a clean, soft cloth. Remove all dirt and debris. INSPECTION/CONVEYOR TABLE (North )(cont’d): ___ Inspect overall condition of the conveyor rollers. ___ Inspect conveyor rollers for bad bearings. Grasp and move each roller to inspect. ___ Inspect condition of the eagle drive belts for the conveyor rollers. Replace as necessary and make sure there are 2 extra belts for each roller. ___ Check Pop-Up Rollers for wear and or damage. Replace as necessary! ___ Check Pop_Up Roller Cylinders (2) for proper operation, leaks, etc. ___ Inspect drive motor and chain. Tension chain as necessary w/1/2" Deflection. ___ Check gearbox for leaks (1). ___ Gearbox is lubed for life. Should be good unless leaking. (If it needs changed use Kluber Synthetic HT-460-5) ___ Insure all guards are in good condition and in place. ___ Inspect e-stop on Operator station for damage/function. ___ Inspect all limit switches (0), photo-eyes (4), light barriers (0), proximity switches (0), Ultrasonic Sensors (0), Mag Door Switches (0), and reflectors (0) for proper alignment, damage, and tightness. Wipe lenses with a clean, soft cloth. Remove all dirt and debris OUTFEED PORTAL: ___ Visually inspect Air Lines for Leaks, Worn Hoses, and Loose Fittings. (i.e. Locknuts on Flow Controls). Listen for leaks. ___ Visually inspect all cables, wiring, conduit, and wire trays for damage and/or proper routing. ___ Inspect all suction cups on the lift for wear and/or damage. ___ Visually inspect vertical lift belt for wear and/or damage. ___ Visually inspect traverse guide wheels for wear and/or damage. ___ Visually inspect guide ways for any damage. ___ Visually inspect vertical guide linear bearings for wear and/or damage. ___ Visually inspect vertical guide ways for any damage. ___ Check air regulator operating pressure. Pressure should be 80 psi or greater. (Located on West Side of Portal Frame) ___ Inspect regulator for wear and/or damage. ___ Inspect gearboxes (2) for obvious leaks and/or damage.
39
OUTFEED PORTAL (cont’d): ___ Change oil in gearboxes (2) on 07/01 of each year. (Vertical Lift Drive Use Shell Omala S2 6 220 Mineral oil) (Traverse Drive Use Kluber Synthetic SEW HT-460-5)
*** NOTE: The date to change the oil will not always fall on the exact day this PM prints. Change the oil on the closest date to the above date that this PM prints.
___ Lubricate all grease zerks. (Use Chevron ULTI-PLEX Synthetic EP grease: 1/2 pump per zerk) ___ Inspect all chains and sprockets for wear and/or damage. Clean and lubricate. Tighten if necessary! ___ Inspect e-stops(2)for damage. ___ Inspect fencing around portal area for damage. ___ Insure all guards are in good condition and in place ___ Inspect all limit switches (0), photo-eyes (1), light barriers (0), proximity switches (12), Ultrasonic Sensors (0), Mag Door Switches (0), and reflectors (0) for proper alignment, damage, and tightness. Wipe lenses with a clean, soft cloth. Remove all dirt and debris. OUTFEED PORTAL CONVEYOR TABLE: ___ Visually inspect Air Lines for Leaks, Worn Hoses, and Loose Fittings. (i.e. Locknuts on Flow Controls). Listen for leaks. ___ Visually inspect all cables, wiring, and conduit for damage and/or proper routing. ___ Inspect all limit switches (), photo-eyes (), light barriers (), proximity switches (), Ultrasonic Sensors (), Mag Door Switches (), and reflectors () for proper alignment, damage, and tightness. Wipe lenses with a clean, soft cloth. Remove all dirt and debris. ___ Observe conveyor while running for proper operation. ___ Inspect overall condition of the rollers. ___ Inspect conveyor rollers for bad bearings. Grasp and move each roller to inspect. ___ Check Pop-Up Rollers for wear and or damage. Replace as necessary! ___ Check Pop Up Roller Cylinders (4) for proper operation, leaks, etc. ___ Inspect Alignment Fence for damage, loose bolts, etc. ___ Inspect Alignment Fence guide ways. Wipe down with light oil. ___ Inspect Alignment Fence Linear Bearings for wear and/or damage. ___ Lubricate all grease zerks. Use EP2 Grease: 1/2 pump per zerk) ___ Inspect drive motor and chain. Tension chain as necessary w/1/2" Deflection. ___ Check gearbox for leaks (1). ___ Gearbox is lubed for life. Should be good unless leaking. (If it needs changed use Kluber Synthetic HT-460-5) ___ Insure all guards are in good condition and in place ___ Inspect all limit switches (0), photo-eyes (4), light barriers (0), proximity switches (0), Ultrasonic Sensors (0), Mag Door Switches (0), and reflectors (0) for proper alignment, damage, and tightness. Wipe lenses with a clean, soft cloth. Remove all dirt and debris OUTFEED PORTAL POWERED ROLLERBED: ___ Observe rollerbed while running for proper operation. ___ Inspect overall condition of the rollers. ___ Inspect all limit switches (0), photo-eyes (2), light barriers (0), proximity switches (0), Ultrasonic Sensors (0), and reflectors (1) for proper alignment, damage, and tightness. Wipe lenses with a clean, soft cloth. Remove all dirt and debris. ___ Visually inspect all cables, wiring, conduit, and wire trays for damage and/or proper routing. ___ Inspect all chains and sprockets for wear and/or damage. Clean and lubricate. Tighten if necessary! ___ Inspect gearboxes (2) for obvious leaks or damage.
40
OUTFEED PORTAL POWERED CDLR ROLLERBED (cont’d): ___ Change oil in gearboxes (2) on 07/01 of each year. (Use Mobil 1 75W90)
*** NOTE: The date to change the oil will not always fall on the exact day this PM prints. Change the oil on the closest date to the above date that this PM prints.
___ Lubricate all grease zerks. (Use Chevron ULTI-PLEX Synthetic EP grease: 1/2 pump per zerk) ___ Inspect all E-Stops (4 cable). ___ Insure all guards are in good condition and in place. ___ Inspect all limit switches (0), photo-eyes (2), light barriers (0), proximity switches (0), Ultrasonic Sensors (0), Mag Door Switches (0), and reflectors (1) for proper alignment, damage, and tightness. Wipe lenses with a clean, soft cloth. Remove all dirt and debris OUTFEED VACUUM PUMP: ___ Visually inspect and listen for any noticeable signs of damage or wear. ___ Blow all dust and debris from unit. ___ Visually inspect all cables, wiring, conduit, and wire trays for damage and/or proper routing. ___ Visually inspect Air Lines for Leaks, Worn Hoses, and Loose Fittings. (i.e. Locknuts on Flow Controls). Listen for leaks. ___ Clean and inspect filter. Replace if necessary! ___ Check mounting bolts for tightness and any other noticeable signs of damage or wear. ___ Reinstall muffler assembly.
41
6.0 Index
6.1 Contact Information
Vendor Contact Person Contact Information Website
Mc Master Carr Anonymous (404) 346-7000
[email protected] www.mcmaster.com
Van Meter Industrial Nick Miller-Mechanical Travis Doyel-Electrical
(319)-368-2867 [email protected] [email protected] www.vanmeterinc.com
Applied Industrial Tim Aldrich (515) 263-1484
[email protected] www.applied.com
Hartfiel Automation Todd Sylvester (515) 974-5714
[email protected] www.hartfiel.com
Braas Company Chris Meyer (800)-852-3583
[email protected] www.braasco.com
Schmalz Desmond Callis (919)-865-0636
[email protected] www.schmalz.com
Igus Tim Wynne 1-800-521-2747
[email protected] www.igus.com
European Woodworking Rosemary Cooper (919)-494-5197
[email protected] www.ewmco.com
Skarda Equipment Matt Ware (402)-422-0430
[email protected] www.skarda.com
Creative Automation Darryl Kuzminski
(715)-223-6321 dkuzminski@creative-
automation.com www.creative-automation.com