CUSTOMER: JOB NUMBER: ITEM #:PLANT NAME: DATE: REVISION:PLANT
LOCATION: PREPARED BY: CASE:SERVICE: CHECKED BY:
PAGE:
SIZE:CODE:DESIGN PRESSURE:OPERATING PRESSURE:ELEVATION (FT):WIND
LOAD (MPH):SEISMIC DESIGN PER ASCE 7-05:
NOT REQUIREDNOT REQUIREDCSCS1.5" H (PP) NOTE 6
HHLLHLLNLLLLLLLLL
1. STAMP VESSEL FOR MAWP, FOR MATERIALS FURNISHED.2. RETAP ALL
COUPLINGS AND PROTECT ALL OPENINGS FOR SHIPMENT.3. FABRICATOR TO
SUPPLY ONE TAILING LUG AND TWO LIFTING LUGS FOR VESSEL.4.
FABRICATOR TO FURNISH TWO 1/4" THICK ANCHOR BOLT TEMPLATE RING.5.
ALL GASKETS TO BE 1/8" THICK SPIRAL WOUND WITH FILTER APPROPRIATE
FOR DESIGN TEMPERATURE.6. FABRICATOR TO PROVIDE INSULATION RINGS
AND INSULATION TO 7'-0" ELEVATION FOR PERSONNEL PROTECTION.7. SKIRT
HEIGHT TO BE MINIMUM.8. TOWER TO HAVE TWO (2) SECTIONS OF PACKING.
FABRICATOR TO PROVIDE WELD-IN SUPPORTS AND INSTALL PACKING. 9.
FABRICATOR TO SUPPLY SHIPPING SUPPORT.10. MAXIMUM ALLOWABLE
DEFLECTION IS 8" PER 100 FEET IN HEIGHT.11. MESH-PAD REQUIRED: YES
(MATERIAL 6" THICK 316LSS) 12 lb/cu ft DENSITY12. FOR N1 AND N2
VENDOR TO PROVIDE INTEGRAL DOWNCOMERS TO 12 FT ABOVE
GRADE13.14.15.16.
REVISION
ISSUED FORENGINEER/DATE
A
RFQSK/SW 2/17/2015
RFQ #:
S-1A/BS-2
N-4 GAS INLET
1
N-6
SKIRT ACCESS2
SA-516-70NSA-516-70NSA-36
2
1LIQUID OUTLET
NO.
SA-105
SA-106-B
NOTES:
MANHOLES
PIPEPIPE
12"
2"
4
12"180 ORIENTATION
RFWN
1N-3
CPLG6000#3/4"2"
RFWN6" 600#
FLANGES:
5
ITEM SERVICE
N-5
SA-105
SA-36
CS / 316L SS
NATIONAL BOARD REGISTRATION REQUIRED: YES
SHELL:
PIPE:
W/ FEED PIPERFWN
BRIDLE
BASE PLATE:
W/ BAFFLE3"
RATING TYPE
600#6"
RFWNN-2 LIQUID INLET (NOTE 12) 1
600#3"
SIZE
W/ B & D
600# RFWNTHREADED
600#
825 PSIG @ 0 / 200F
PACKING:
600#
NOZZLE SCHEDULE
N-1 GAS OUTLET (NOTE 12) 1 RFWNREMARKS
PLATFORMS:
INSULATION:
LADDER:
RE-PADS:CLIPS:
OF
INTERNALS:
1
20184 PER FERC
COLUMN SPECIFICATION SHEET
15-0391 TT-35002/17/2015 A
JACKSONVILLE, FL SK DESIGNAMINE CONTACTOR SW 1REQUIRED #
HEADS:SKIRT:
2
316L SS
MATERIAL SPECIFICATION
100% RTYES
RADIOGRAPH:STRESS RELIEVE:
HARDNESS / IMPACT TEST:STAMP:JOINT EFFICIENCY:HYDROTEST: PER
CODE
DESIGN DATA
PER CODEYESPER CODE
24" I.D. X 56'-0" S/SASME SECTION VIII, DIV. 1
0.125CORROSION ALLOWANCE (IN.):Ss =14.7% g;S1 = 6.2%
g;IF=1.25;CATEGORY =C
750 PSIG @ 130F
TW/TE/TI
SKIRT VENT
MW-1
OVERTURNING MOMENT AT BASE:
COUPLINGS:
LIQUID LEVELSLEVEL, IN R. TIME, MIN
