Upload
others
View
13
Download
4
Embed Size (px)
Citation preview
Printouts, if any, are not controlled. Printed on: 23/01/2018
Mondi Štětí a.s.
STANDARD
Part 13.02
STAINLESS STEEL PIPING
Mondi Štětí a.s. STANDARD 13.02 Page: 1/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
STANDARD
Part 13.02
STAINLESS STEEL PIPING
Worked out by: Verified by: Approved by: Name: Name: Name: Position: Position: Position: Signed by: Signed by: Signed by:
Mondi Štětí a.s. STANDARD 13.02 Page: 2/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
CONTENT 13.02.01 Pipe classes 0H...63H 13.02.02 Allowable pressures at elevated temperatures 13.02.03 Pipes for pipe classes 6H...63H 13.02.04 Vacuum pipes, pipe class 0H 13.02.05 Elbows for pipe classes 0H...63H 13.02.06 Reducers for pipe classes 0H...63H 13.02.07 Tee pieces for pipe classes 0H...63H 13.02.08 Reinforced branch connections – allowable pressures 13.02.09 Reinforced branch connection with plate 13.02.10 Blank flange 0H...25H 13.02.11 Spade blank 13.02.12 Open spade 13.02.13 Plate valve 13.02.14 Drain and spooling connection DN 40 and DN 50 13.02.15 Vent connection DN 25 13.02.16 Sample taking connection DN 40
Mondi Štětí a.s. STANDARD 13.02 Page: 3/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
TABLE OF CONTENTS Page
1 Pipe classes 0H…63H ............................................................................................................ 4
2 Allowable pressures at elevated temperatures ................................................................... 8 3 Pipes for pipe classes 6H...63H........................................................................................... 10
4 Vacuum pipes, pipe class 0H ............................................................................................... 12 5 Elbows for Pipe Classes 0H...63H ...................................................................................... 14
6 Reducers for pipe classes 0H...63H ................................................................................... 16 7 Tee pieces for pipe classes 0H...63H ................................................................................. 21
8 Reinforced branch connections – allowable pressures ................................................... 25
9 Reinforced branch connection with plate ........................................................................... 32
10 Blank flange 0H...25H ........................................................................................................... 34
11 Spade blank ............................................................................................................................ 35 12 Open spade ............................................................................................................................. 37
13 Plate valve ............................................................................................................................... 39 14 Drain and spooling connection DN 40 and DN 50 ............................................................ 41 15 Vent connection DN 25 ......................................................................................................... 43
16 Sample taking connection DN 40 ........................................................................................ 44
Mondi Štětí a.s. STANDARD 13.02.01 Page: 4/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
1 Pipe classes 0H…63H
1.1 General This standard presents dimension standards and material specifications for piping components of normal stainless steel pipe classes. 1.2 Pipe classes
Pipe
class
0H2A
0H1A
6H2A
6H1A
10H3A
10H2A
10H1A
16H3A
16H2A
16H1A
25H3A
25H2A
25H1A
40H2A
40H1A
63H2A
63H1A
Design pressure1)
(MPa) at 20 °C
0 (abs)
0.6
1.0
1.6
2.5
4.0
6.3
1) Design pressure is internal overpressure (pe), except for pipe classes 0H1A and 0H2A where design pressure 0 refers to absolute pressure = 0.1 MPa external pressure (full vacuum)
Mondi Štětí a.s. STANDARD 13.02.01 Page: 5/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
1.3 Piping components for 0H1A...63H1A
Piping components
Dimension standard
Material Remarks
4) Designation Standard Certificate
EN 10204-
Pipe EN 10217-7,
13.02.03
1.4307 EN 10217-7 3.1
Vacuum pipe EN 10217-7,
13.02.04
1.4307 EN 10217-7 3.1
Elbow EN 10253-4,
13.02.05
1.4307 EN 10253-4 3.1
Reducer EN 10253-4,
13.02.06
1.4307 EN 10253-4 3.1
Tee piece EN 10253-4,
13.02.07
1.4307 EN 10253-4 3.1
Collar EN 1092-1
Type 35 ,PN 10…40
1.4307 EN 10028-7 3.1
Flange EN 1092-1
Type 02, PN 10…40
Type 11-B11 PN 63
P265GH
1.4307
EN 10028-2
EN 10222-5
3.1
Hot dip galvanized
-
Blank flange EN 1092-1 Type 05/ lining plate,
PN 10…63
13.02.10
P265GH/
1.4307 lining plate
EN 10028-2/
EN 10028-7
3.1
3.1
Hot dip galvanized
with 1.4307 plate
Blank and open spade 13.02.11/12 P265GH/
1.4307 lining plate
EN 10028-2/
EN 10028-7
3.1
3.1
Plate valve 13.02.13 1.4307 EN 10217-7 3.1
Cap EN 10253-4,
Wall thickness same as pipe wall thickness
1.4307 EN 10253-4 3.1
Hex head bolt 3) EN ISO 4014 8.8 5), (T< 300°C)
25CrMo4
EN ISO 898-1
EN 10269
2.2
3.1
Hot dip galvanized
-
Nut 3) EN ISO 4032 8 5) (T< 300°C)
C35E
EN ISO 898-2
EN 10269
2.2
3.1
Hot dip galvanized
-
Washer ISO 7089 Gr. A S 235JR EN 10025-2 Hot dip galvanized
Gasket EN 1514-1 Type IBC
PN 10…63 1)
2)
Threaded fittings EN 10241 1.4404 EN 10272 3.1 Thread according to ISO 7-1 (R thread)
Not for 63H1A
1) Gasket thickness 2.0 mm 2) Gasket material depends on flow substance. See 13.01.01 “Technical Specification for Flow Substances, Pipe and Valve Type
Selection”. 3) Material for hexagon head bolts in pipe class 63H1A is 25CrMo4 and nuts C35E according to EN 10269. 4) Weld joint coefficient=1 5) Starting material shall comply with EN 10269. Material certificate from base material.
Mondi Štětí a.s. STANDARD 13.02.01 Page: 6/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
1.4 Piping components for 0H2A...63H2A
Piping components
Dimension standard
Material Remarks
4) Designation Standard Certificate
EN 10204-
Pipe EN 10217-7,
13.02.03
1.4404 EN 10217-7 3.1
Vacuum pipe EN 10217-7,
13.02.04
1.4404 EN 10217-7 3.1
Elbow EN 10253-4,
13.02.05
1.4404 EN 10253-4 3.1
Reducer EN 10253-4,
13.02.06
1.4404 EN 10253-4 3.1
Tee piece EN 10253-4,
13.02.07
1.4404 EN 10253-4 3.1
Collar EN 1092-1
Type 35 ,PN 10…40
1.4404 EN 10028-7 3.1
Flange EN 1092-1
Type 02, PN 10…40
Type 11-B11 PN 63
P265GH
1.4404
EN 10028-2
EN 10222-5
3.1
Hot dip galvanized
-
Blank flange EN 1092-1 Type 05/ lining plate,
PN 10…63
13.02.10
P265GH/
1.4404 lining plate
EN 10028-2/
EN 10028-7
3.1
3.1
Hot dip galvanized
with 1.4404 plate
Blank and open spade 13.02.11/ 12 P265GH/
1.4404 lining plate
EN 10028-2/
EN 10028-7
3.1
3.1
Plate valve 13.02.13 1.4404 EN 10217-7 3.1
Cap EN 10253-4,
Wall thickness same as pipe wall thickness
1.4404 EN 10253-4 3.1
Hex head bolt 3) EN ISO 4014 8.8 5), (T< 300°C)
25CrMo4
EN ISO 898-1
EN 10269
2.2
3.1
Hot dip galvanized
-
Nut 3) EN ISO 4032 8 5) (T< 300°C)
C35E
EN ISO 898-2
EN 10269
2.2
3.1
Hot dip galvanized
-
Washer ISO 7089 Gr. A S 235JR EN 10025-2 Hot dip galvanized
Gasket EN 1514-1 Type IBC
PN 10…63 1)
2)
Threaded fittings EN 10241 1,4404 EN 10272 3.1 Thread according to ISO 7-1 (R thread)
Not for 63H2A
1) Gasket thickness 2.0 mm 2) Gasket material depends on flow substance. See 13.01.01 “Technical Specification for Flow Substances, Pipe and Valve Type
Selection”. 3) Material for hexagon head bolts in pipe class 63H2A is 25CrMo4 and nuts C35E according to EN 10269. 4) Weld joint coefficient=1 5) Starting material shall comply with EN 10269. Material certificate from base material.
Mondi Štětí a.s. STANDARD 13.02.01 Page: 7/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
1.5 Piping components for 10H3A...25H3A
Piping components
Dimension standard
Material Remarks
3) Designation Standard Certificate
EN 10204-
Pipe EN 10217-7,
13.02.03
1.4462
(duplex)
EN 10217-7 3.1
Vacuum pipe EN 10217-7,
13.02.04
1.4462
(duplex)
EN 10217-7 3.1
Elbow EN 10253-4,
13.02.05
1.4462
(duplex)
EN 10253-4 3.1
Reducer EN 10253-4,
13.02.06
1.4462
(duplex)
EN 10253-4 3.1
Tee piece EN 10253-4,
13.02.07
1.4462
(duplex)
EN 10253-4 3.1
Collar EN 1092-1
Type 35 ,PN 10…25
1.4462
(duplex)
EN 10028-7 3.1
Flange EN 1092-1
Type 02, PN 10…25
P265GH
EN 10028-2
3.1
Hot dip galvanized
Blank flange EN 1092-1 Type 05/ lining plate,
PN 10…25
13.02.10
P265GH/
1.4462 lining plate
(duplex)
EN 10028-2/
EN 10028-7
3.1
3.1
Hot dip galvanized
with 1.4462 plate
Blank and open spade 13.02.11/ 12 P265GH/
1.4462 lining plate
(duplex)
EN 10028-2/
EN 10028-7
3.1
3.1
Hot dip galvanized
with 1.4462 plate
Plate valve 13.02.13 1.4462
(duplex)
EN 10217-7 3.1
Cap EN 10253-4,
Wall thickness same as pipe wall thickness
1.4462
(duplex)
EN 10253-4 3.1
Hex head bolt EN ISO 4014 8.8 5), (T< 300°C)
25CrMo4
EN ISO 898-1
EN 10269
2.2
3.1
Hot dip galvanized
-
Nut EN ISO 4032 8 5) (T< 300°C)
C35E
EN ISO 898-2
EN 10269
2.2
3.1
Hot dip galvanized
-
Washer ISO 7089 Gr. A S 235JR EN 10025-2 Hot dip galvanized
Gasket EN 1514-1 Type IBC
PN 10…25 1)
2)
Threaded fittings EN 10241 1,4462 or equal EN 10272 3.1 Thread according to ISO 7-1 (R thread)
1) Gasket thickness 2.0 mm 2) Gasket material depends on flow substance. See 13.01.01 “Technical Specification for Flow Substances, Pipe and Valve Type
Selection”. 3) Weld joint coefficient=1
4) Starting material shall comply with EN 10269. Material certificate from base material.
Mondi Štětí a.s. STANDARD 13.02.02 Page: 8/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
2 Allowable pressures at elevated temperatures 2.1 General This standard gives the coefficient k for defining the allowable pressures at elevated temperatures generally for Pipe classes and in detail for branch connections presented in standard 13.02.08. 2.2 Limitations The allowable pressure shall not exceed the nominal pressure of Pipe Classes 6H...63H. 2.3 Coefficient k
Temperature oC
k coefficient for material grades
1.4307 1.4404 1.4462
20 1 1 1
50 0,93 0,96 0,92
75 0,89 0,92 0,86
100 0,84 0,88 0,80
125 0,80 0,84 0,77
150 0,75 0,80 0,74
175 0,72 0,77 0,72
200 0,68 0,74 0,69
where 1.4307 corresponds to H1 1.4404 corresponds to H2 1.4462 corresponds to H3 2.4 Examples
Example 1: Pipe Class 25H2A Temperature = 150 ºC Coefficient k = 0.8 The allowable pressure = 0.8 x 25 bar = 20 bar, which means that all components of that Pipe Class 25H2A stand the pressure 2.0 MPa.
Mondi Štětí a.s. STANDARD 13.02.02 Page: 9/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Example 2:
Pipe class 6H1A Temperature = 20 ºC Coefficient k = 1.00 The allowable pressure = 1.00 x 6 bar = 6.0 bar, which means that the Pipe Class can be used up to 0.6 MPa. Example 3: Reinforced branch connection with plate reinforcement of Pipe Class 16H, DN 800/ DN 500 Temperature = 150 ºC Coefficient k = 0.80 Allowable pressure from standard 02-011 is 1.62 MPa The allowable pressure = 0.8 x 1.62 MPa = 1.29 MPa, which means that the reinforced branch connection stands the pressure 1.29 MPa.
Mondi Štětí a.s. STANDARD 13.02.03 Page: 10/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
3 Pipes for pipe classes 6H...63H
3.1 Dimensions
DN Do x s
0H 1),
6H
10H 16H 25H 40H 63H
6 10.2 x 1.6
10 17.2 x 1.6 According to
15 21.3 x 1.6 According to 6H
20 26.9 x 1.6 According to 6H
25 33.7 x 1.6 According to 6H
(32) 42.4 x 1.6 According to 6H
40 48.3 x 1.6 6H
50 60.3 x 1.6 60.3 x 2.0
(65) 76.1 x 1.6 76.1 x 2.6
80 88.9 x 2.0 88.9 x 3.2
100 114.3 x 2.0 114.3 x 2.6 114.3 x 4.0
(125) 139.7 x 2.0 139.7 x 3.2 139.7 x 5.0
150 168.3 x 2.0 168.3 x 2.6 168.3 x 4.0 168.3 x 6.3
200 219.1 x 2.0 219.1 x 3.2 219,1 x 5.0
250 273 x 2.0 273 x 2.6 273 x 4.0 273 x 6.3
300 323.9 x 2.6 323.9 x 3.2 323.9 x 5.0
350 355.6 x 2.6 355.6 x 3.2 355.6 x 5.0
400 406.4 x 3.2 406.4 x 4.0 406.4 x 6.3
(450) 457 x 3.2 457 x 5.0 457 x 8.0
500 508 x 4.0 508 x 6.3 508 x 10
600 610 x 4.0 610 x 5.0 610 x 8.0 610 x 12.5
700 711 x 4.0 711 x 5.0 711 x 8.0 711 x 12.5
800 813 x 4.0 813 x 6.3 813 x 10 813 x 12.5
900 914 x 4.0 914 x 8.0 914 x 10
1000 1016 x 5.0 1016 x 8.0 1016 x 12,5
1200 1220 x 6.3 1220 x 10
The nominal sizes inside parenthesis shall be avoided. 1) Reinforcement rings against vacuum are presented in the standard
13.02.04.
Mondi Štětí a.s. STANDARD 13.02.03 Page: 11/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
3.2 Designation Name, Do x s, material, standard No. Example: Pipe, 114.3 x 2.0, 1.4404, EN 10217-7
Mondi Štětí a.s. STANDARD 13.02.04 Page: 12/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
4 Vacuum pipes, pipe class 0H 4.1 Dimensions
DN Do s Lmax b x h
200 219.1 2.0 2000 30 x 6
250 273 2.0 1700 30 x 6
300 323.9 2.6 2200 30 x 6
350 355.6 2.6 2300 35 x 8
400 406.4 3.2 2800 40 x 8
(450) 457 3.2 2800 40 x 8
500 508 4.0 3500 50 x 8
600 610 4.0 2600 60 x 6
700 711 4.0 2300 60 x 6
800 813 4.0 1700 60 x 6
900 914 4.0 1500 60 x 6
1000 1016 5.0 2200 70 x 8
1200 1220 6.3 2900 90 x 8
Mondi Štětí a.s. STANDARD 13.02.04 Page: 13/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Notes: The effective throat thickness of fillet weld for the reinforcement ring is 0.7 x s, were s is the wall thickness of the pipe. Length of the welds on both sides of the ring must be at least 0.5 x circumference of the pipe. When using intermittent weld, the distance between welds must not exceed 8 x wall thickness of the pipe. Nominal sizes DN 6 - DN 150 do not need the reinforcement rings against vacuum when the wall thicknesses are according to the pipe class 6H. Extra reinforcement rings must be welded on to the pipe at both ends near bends. 4.2 Designation Name, Do x s, material, standard No. Example: Vacuum pipe, 406.4 x 3.2, 1.4404, 13.02.04
Mondi Štětí a.s. STANDARD 13.02.05 Page: 14/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
5 Elbows for Pipe Classes 0H...63H 5.1 Dimensions
Table 1 Dimensions according to pipe classes
DN
Do x s R Type
0H 6H
10H 16H 25H 1.5D 2.5D
6 10.2 x 2.0 R = 3...5D Elbow or bent pipe
10 17.2 x 2.0 28
15 21.3 x 2.0 According to 28 45
20 26.9 x 2.0 According to 6H 29 57
25 33.7 x 2.0 According to 6H 38 72
(32) 42.4 x 2.0 6H 48 93
40 48.3 x 2.0 57 108
50 60.3 x 2.0 76 135
(65) 76.1 x 2.0 95 175
80 88.9 x 2.0 114 205
100 114.3 x 2.0 114.3 x 2.6 152 270
(125) 139.7 x 2.0 139.7 x 3.2 190 330
150 168.3 x 2.0 168.3 x 2.6 168.3 x 4.0 229 390 R = 1.5D
200 219.1 x 2.0 219.1 x 3.2 219.1 x 5.0 305 510
250 273 x 2.0 273 x 2.6 273 x 4.0 273 x 6.3 381 650 Pressed elbow
300 323.9 x 2.6 323.9 x 3.2 323.9 x 4.0 323.9 x 6.3 457 775
350 355.6 x 2.6 355.6 x 3.2 355.6 x 4.0 355.6 x 6.3 533 850
400 406.4 x 3.2 406.4 x 4.0 406.4 x 5.0 406.4 x 8.0 610 970
(450) 457 x 3.2 457 x 4.0 457 x 6.3 457 x 10 686 1122
500 508 x 4.0 508 x 5.0 508 x 8.0 508 x 12.5 762 1245
600 610 x 4.0 610 x 6.3 610 x 10.0 610 x 12.5 914 1524
700 711 x 5.0 711 x 6.3 711 x 10.0 711 x 12.5 1067 R = 1.5D
800 813 x 5.0 813 x 8.0 813 x 12.5 813 x 14.2 1219 Mitre elbow
900 914 x 5.0 914 x 8.0 914 x 12.5 1372
1000 1016 x 6.3 1016 x 10 1016 x 12.5 1524
1200 1220 x 8.0 1220 x 12.5 1830
Mondi Štětí a.s. STANDARD 13.02.05 Page: 15/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
DN
Do x s
R
Type
40H 63H
10 17.2 x 1.6 According to 3...5D
15 21.3 x 2.0 40H 28 Bent
20 26.9 x 2.0 29 pipe
25 33.7 x 2.0 38 or elbow
(32) 42.4 x 2.0 42.4 x 3.2 48
40 48.3 x 2.0 48.3 x 3.2 57 R = 1.5D
50 60.3 x 2.6 60.3 x 4.0 76
(65) 76.1 x 3.2 76.1 x 5.0 95 Pressed elbow
80 88.9 x 3.2 88.9 x 5.0 114
100 114.3 x 5.0 114.3 x 6.3 152
(125) 139.7 x 5.0 139.7 x 6.3 190
150 168.3 x 6.3 168.3 x 8.0 229
200 219.1 x 8.0 305
250 273 x 10.0 381
The nominal sizes inside parenthesis shall be avoided. 5.2 Designation Name, Do x s, R, material, standard No. Example: Elbow, 219.1 x 2.0, 305, 1.4404, 13.02.05
Mondi Štětí a.s. STANDARD 13.02.06 Page: 16/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
6 Reducers for pipe classes 0H...63H 6.1 Dimensions
See the following table for dimensions.
L = 2.96 x (Do1 - Do2)
6.2 Sudden reducer Sudden reducer, type S, is to be used for pulp on the suction side of a pump when
consistency C is 4 %. Design of sudden reducer shall be verified with strength calculations by the Supplier. The given plate thickness of 10 mm is minimum requirement.
Mondi Štětí a.s. STANDARD 13.02.06 Page: 17/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Type S
Mondi Štětí a.s. STANDARD 13.02.06 Page: 18/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
6.3 Dimensions for pipe classes 0H...63H
DN1
DN2
Do1
Do2
L Wall thickness s
mm mm mm 0H 6H
10H 16H 25H 40H 63H
25 10 15 20
33.7 17.2 21.3 26.9
49 37 20
2.0 2.0 2.0
According to 6H
According to 6H
(32) 10 15 20 25
42.4 17.2 21.3 26.9 33.7
75 62 46 26
2.0 2.0 2.0 2.0
According
According
to 6H
40 15 20 25 32
48.3 21.3 26.9 33.7 42.4
80 63 43 17
2.0 2.0 2.0 2.0
According
to 6H
2.6 2.6 2.6 2.6
50 20 25 32 40
60.3 26.9 33.7 42.4 48.3
99 79 53 36
2.0 2.0 2.0 2.0
to 6H
3.2 3.2 3.2 3.2
(65) 25 32 40 50
76.1 33.7 42.4 48.3 60.3
126 100 82 47
2.0 2.0 2.0 2.0
2.6 2.6 2.6 2.6
4.0 4.0 4.0 4.0
80 32 40 50
(65)
88.9 42.4 48.3 60.3 76.1
138 120 85 38
2.0 2.0 2.0 2.0
2.6 2.6 2.6 2.6
4.0 4.0 4.0 4.0
100 40 50
(65) 80
114.3
48.3 60.3 76.1 88.9
195 160 113 75
2.0 2.0 2.0 2.0
2.6 2.6 2.6 2.6
3.2 3.2 3.2 3.2
5.0 5.0 5.0 5.0
(125) 50
(65) 80 100
139.7
60.3 76.1 88.9 114.
3
235 188 151 75
2.0 2.0 2.0 2.0
2.6 2.6 2.6 2.6
4.0 4.0 4.0 4.0
6.3 6.3 6.3 6.3
150 (65) 80 100
(125)
168.3
76.1 88.9 114.
3 139.
7
273 234 160 85
2.0 2.0 2.0 2.0
3.2 3.2 3.2 3.2
5.0 5.0 5.0 5.0
8.0 8.0 8.0 8.0
Mondi Štětí a.s. STANDARD 13.02.06 Page: 19/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
DN1
DN2
Do1
Do2
L Wall thickness s / mm
mm mm mm 0H
6H
10H
16H 25H 40H
200 80 100 (125) 150
219.1 88.9 114.3 139.7 168.3
385 310 235 150
2.6 2.6 2.6 2.6
According
According
4.0 4.0 4.0 4.0
6.3 6.3 6.3 6.3
250 100 (125) 150 200
273.0 114.3 139.7 168.3 219.1
470 395 310 160
3.2 3.2 3.2 3.2
to 6H to 6H
5.0 5.0 5.0 5.0
8.0 8.0 8.0 8.0
300 (125) 150 200 250
323.9 139.7 168.3 219.1 273.0
545 461 310 151
3.2 3.2 3.2 3.2
5.0 5.0 5.0 5.0
350 150 200 250 300
355.6 168.3 219.1 273.0 323.9
554 404 244 94
3.2 3.2 3.2 3.2
4.0 4.0 4.0 4.0
5.0 5.0 5.0 5.0
400 200 250 300 350
406.4 219.1 273.0 323.9 355.6
554 395 244 150
3.2 3.2 3.2 3.2
4.0 4.0 4.0 4.0
6.3 6.3 6.3 6.3
(450) 250 300 350 400
457.0 273.0 323.9 355.6 406.4
545 395 301 150
4.0 4.0 4.0 4.0
6.3 6.3 6.3 6.3
10 10 10 10
500 300 350 400 (450)
508.0 323.9 355.6 406.4 457.0
545 451 301 150
4.0 4.0 4.0 4.0
5.0 5.0 5.0 5.0
6.3 6.3 6.3 6.3
10 10 10 10
600 350 400 (450) 500
610.0 355.6 406.4 457.0 508.0
752 601 451 301
4.0 4.0 4.0 4.0
5.0 5.0 5.0 5.0
8.0 8.0 8.0 8.0
12.5 12.5 12.5 12.5
700 400 (450) 500 600
711.0 406.4 457.0 508.0 610.0
902 752 601 301
4.0 4.0 4.0 4.0
6.3 6.3 6.3 6.3
10 10 10 10
12.5 12.5 12.5 12.5
800 (450) 500 600 700
813.0 457.0 508.0 610.0 711.0
1053 902 601 301
5.0 5.0 5.0 5.0
6.3 6.3 6.3 6.3
10 10 10 10
12.5 12.5 12.5 12.5
900 500 600 700 800
914.0 508.0 610.0 711.0 813.0
1203 902 601 301
5.0 5.0 5.0 5.0
8.0 8.0 8.0 8.0
10 10 10 10
1000 600 700 800 900
1016.0 610.0 711.0 813.0 914.0
1203 902 601 301
6.3 6.3 6.3 6.3
8.0 8.0 8.0 8.0
12,5 12,5 12,5 12,5
1200 700 800 900 1000
1220.0 711.0 813.0 914.0 1016.0
1506 1205 905 604
6.3 6.3 6.3 6.3
10.0 10.0 10.0 10.0
Mondi Štětí a.s. STANDARD 13.02.06 Page: 20/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Note: The wall thickness of reducer is at least the same as the wall thicknesses of the pipe at the bigger end of the reducer, however at least 2 mm. 6.4 Designation Name, type, DN1/ DN2 x s, material, standard No. Example 1: Reducer, C, 500/ 350 x 4.0, 1.4404, EN 10253-4 Example 2: Reducer, S, 500/ 350 x 4.0, 1.4404, 13.02.06
Mondi Štětí a.s. STANDARD 13.02.07 Page: 21/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
7 Tee pieces for pipe classes 0H...63H 7.1 Dimensions
Dimensions are according to Table 1.
Mondi Štětí a.s. STANDARD 13.02.07 Page: 22/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Table 1
DN1 DN2 Do1
mm
Do2
mm
L
mm
0H
6H s1 / s2
10H
s1 / s2
16H
s1 / s2
25H
s1 / s2
40H
s1 / s2
63H
s1 / s2
(32) 32 42.4 42.4 48 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.6
(32) 25 42.4 33.7 48 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.0
40 40 48.3 48.3 57 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 3.2 3.2
40 32 48.3 42.4 57 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 3.2 2.0
50 50 60.3 60.3 125 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.6 4.0 4.0
50 40 60.3 48.3 125 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.0 4.0 2.0
(65) 65 76.1 76.1 140 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.6 3.2 3.2 5.0 5.0
(65) 50 76.1 60.3 140 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.0 3.2 2.6 5.0 2.6
80 80 88.9 88.9 150 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.6 4.0 4.0 5.0 5.0
80 (65) 88.9 76.1 150 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.0 4.0 2.6 5.0 4.0
100 100 114.3 114.3 160 2.0 2.0 2.0 2.0 2.6 2.6 3.2 3.2 5.0 5.0 6.3 6.3
100 80 114.3 88.9 160 2.0 2.0 2.0 2.0 2.6 2.0 3.2 2.6 5.0 3.2 6.3 5.0
(125) 125 139.7 139.7 180 2.0 2.0 2.0 2.0 3.2 3.2 4.0 4.0 6.3 6.3 8.0 8.0
(125) 100 139.7 114.3 180 2.0 2.0 2.0 2.0 3.2 2.0 4.0 3.2 6.3 4.0 8.0 6.3
150 150 168.3 168.3 200 2.0 2.0 2.6 2.6 4.0 4.0 5.0 5.0 8.0 8.0 10.0 10.0
150 (125) 168.3 139.7 200 2.0 2.0 2.6 2.0 4.0 2.0 5.0 4.0 8.0 4.0 10.0 8.0
200 200 219.1 219.1 250 2.6 2.6 3.2 3.2 5.0 5.0 6.3 6.3 10.0 10.0
200 150 219.1 168.3 250 2.6 2.0 3.2 2.6 5.0 2.6 6.3 5.0 10.0 5.0
250 250 273.0 273.0 300 3.2 3.2 4.0 4.0 6.3 6.3 8.0 8.0 12.5 12.5
250 200 273.0 219.1 300 3.2 2.6 4.0 3.2 6.3 3.2 8.0 6.3 12.5 8.0
300 300 323.9 323.9 330 3.2 3.2 5.0 5.0 6.3 6.3 10.0 10.0
300 250 323.9 273.0 330 3.2 3.2 5.0 4.0 6.3 6.3 10.0 6.3
350 350 355.6 355.6 360 4.0 4.0 5.0 5.0 8.0 8.0 10.0 10.0
350 300 355.6 323.9 360 4.0 3.2 5.0 5.0 8.0 6.3 10.0 10.0
Mondi Štětí a.s. STANDARD 13.02.07 Page: 23/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Table 1 (continues)
DN1 DN2 Do1
mm
Do2
mm
L
mm
0H
6H
s1 / s2
10H
s1 / s2
16H
s1 / s2
25H
s1 / s2
400 400 406.4 406.4 400 4.0 4.0 6.3 6.3 8.0 8.0 12.5 12.5
400 350 406.4 355.6 400 4.0 4.0 6.3 5.0 8.0 8.0 12.5 10.0
(450) 450 457.0 457.0 450 5.0 5.0 6.3 6.3 10.0 10.0 12.5 12.5
(450) 400 457.0 406.4 450 5.0 4.0 6.3 6.3 10.0 8.0 12.5 12.5
500 500 508.0 508.0 500 5.0 5.0 8.0 8.0 10.0 10.0 14.2 14.2
500 (450) 508.0 457.0 500 5.0 5.0 8.0 6.3 10.0 10.0 14.2 12.5
600 600 610.0 610.0 600 6.3 6.3 10.0 10.0 12.5 12.5 17.5 17.5
600 500 610.0 508.0 600 6.3 5.0 10.0 6.3 12.5 10.0 17.5 14.2
700 700 711.0 711.0 700 8.0 8.0 10.0 10.0 14.2 14.2 20.0 20.0
700 600 711.0 610.0 700 8.0 5.0 10.0 10.0 14.2 12.5 20.0 16.0
800 800 813.0 813.0 800 8.0 8.0 12.5 12.5 16.0 16.0 20.0 20.0
800 700 813.0 711.0 800 8.0 8.0 12.5 10.0 16.0 14.2 20.0 20.0
900 900 914.0 914.0 900 10.0 10.0 12.5 12.5 16.0 16.0
900 800 914.0 813.0 900 10.0 8.0 12.5 12.5 16.0 16.0
1000 1000 1016.0 1016.0 1000 10.0 10.0 14.2 14.2 20.0 20.0
1000 900 1016.0 914.0 1000 10.0 10.0 14.2 12.5 20.0 16.0
1200 1200 1220.0 1220.0 1200 12.5 12.5
1200 1000 1220.0 1016 1200 12.5 12.5
Mondi Štětí a.s. STANDARD 13.02.07 Page: 24/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
7.2 Designation
Name, DN1/ DN2, s1/s2, material, standard No. Example: Tee piece, 200/ 200, 3.2/ 3.2, 1.4404, EN 10253-4
Mondi Štětí a.s. STANDARD 13.02.08 Page: 25/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
8 Reinforced branch connections – allowable pressures 8.1 General
The allowed pressures for the normal wall thicknesses for each pipe class have been calculated according to EN 13480-3. The pipes are with wall thicknesses according to different pipe classes. The branches are reinforced with plate. See standard 13.02.09.
8.2 Calculation basis Material 1.4404 Temperature t = 20 C Corrosion allowance c o = 0 mm Tolerance allowance c = 10 % however at least ± 0.2 mm for diameters 21...1220 mm
Welding factor z = 1.0
Allowable pressures are presented in MPa
8.3 Tables
Allowable pressure tables for normal walls of pipe classes:
Table 1 6H reinforced-branch connection Table 2 10H reinforced-branch connection Table 3 16H reinforced-branch connection Table 4 25H reinforced-branch connection Table 5 40H reinforced-branch connection Table 6 63H reinforced-branch connection
Mondi Štětí a.s. STANDARD 13.02.08 Page: 26/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Table 1 Allowable pressure (MPa) for reinforced-branch connection See standard 13.01.06, item 2.2 Pipe class 6H
Outside Outside diameter of connecting pipe (mm)
diameter
main 48,3 60,3 76,1 88,9 114,3 139,7 168,3 219,1 273,0 323,9 355,6 406,4 457,0 508,0 610,0 711,0 813,0 914,0 1016,0 1220,0
pipe Wall 1,6 1,6 1,6 2,0 2,0 2,0 2,0 2,0 2,0 2,6 2,6 3,2 3,2 4,0 4,0 4,0 4,0 4,0 5,0 6,3
48,3 1,6 5,23
60,3 1,6 4,57 3,89
76,1 1,6 3,94 3,38 2,85
88,9 2,0 4,56 3,92 3,31 3,24
114,3 2,0 3,84 3,33 2,84 2,78 2,31
139,7 2,0 3,33 2,91 2,50 2,44 2,04 1,76
168,3 2,0 2,91 2,56 2,21 2,16 1,81 1,57 1,36
219,1 2,0 2,39 2,12 1,84 1,80 1,52 1,33 1,16 0,95
273,0 2,0 2,02 1,80 1,58 1,54 1,31 1,15 1,00 0,83 0,70
323,9 2,6 2,35 2,12 1,87 1,79 1,53 1,34 1,18 0,97 0,82 0,79
355,6 2,6 2,19 1,97 1,75 1,67 1,44 1,26 1,11 0,92 0,78 0,75 0,70
406,4 3,2 2,48 2,25 2,01 1,91 1,65 1,46 1,28 1,06 0,90 0,85 0,79 0,77
457,0 3,2 2,25 2,05 1,84 1,75 1,52 1,34 1,19 0,99 0,84 0,79 0,74 0,72 0,66
508,0 4,0 2,65 2,43 2,20 2,08 1,82 1,62 1,44 1,20 1,02 0,95 0,88 0,84 0,77 0,77
610,0 4,0 2,28 2,10 1,91 1,81 1,60 1,42 1,27 1,07 0,91 0,85 0,79 0,75 0,69 0,69 0,60
711,0 4,0 2,00 1,85 1,69 1,61 1,42 1,28 1,14 0,97 0,83 0,77 0,72 0,68 0,63 0,63 0,54 0,48
813,0 4,0 1,78 1,66 1,52 1,45 1,29 1,16 1,04 0,88 0,76 0,70 0,66 0,63 0,58 0,57 0,50 0,45 0,40
914,0 4,0 1,61 1,50 1,38 1,32 1,18 1,06 0,96 0,82 0,70 0,65 0,61 0,58 0,53 0,53 0,46 0,41 0,37 0,34
1016,0 5,0 1,88 1,77 1,64 1,56 1,41 1,28 1,16 0,99 0,86 0,79 0,74 0,70 0,64 0,63 0,55 0,49 0,44 0,40 0,40
1220,0 6,3 2,06 1,95 1,83 1,75 1,59 1,46 1,34 1,16 1,02 0,93 0,88 0,82 0,75 0,72 0,63 0,56 0,51 0,46 0,45 0,43
Mondi Štětí a.s. STANDARD 13.02.08 Page: 27/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Table 2 Allowable pressure (MPa) for reinforced-branch connection See standard 13.01.06, item 2.2
Pipe class 10H
Outside Outside diameter of connecting pipe (mm)
diameter
main 48,3 60,3 76,1 88,9 114,3 139,7 168,3 219,1 273,0 323,9 355,6 406,4 457,0 508,0 610,0 711,0 813,0 914,0 1016,0 1220,0
pipe Wall 1,6 1,6 1,6 2,0 2,0 2,0 2,0 2,0 2,0 2,6 2,6 3,2 3,2 4,0 5,0 5,0 6,3 8,0 8,0 10,0
48,3 1,6 5,23
60,3 1,6 4,57 3,89
76,1 1,6 3,94 3,38 2,85
88,9 2,0 4,56 3,92 3,31 3,24
114,3 2,0 3,84 3,33 2,84 2,78 2,31
139,7 2,0 3,33 2,91 2,50 2,44 2,04 1,76
168,3 2,0 2,91 2,56 2,21 2,16 1,81 1,57 1,36
219,1 2,0 2,39 2,12 1,84 1,80 1,52 1,33 1,16 0,95
273,0 2,0 2,02 1,80 1,58 1,54 1,31 1,15 1,00 0,83 0,70
323,9 2,6 2,35 2,12 1,87 1,79 1,53 1,34 1,18 0,97 0,82 0,79
355,6 2,6 2,19 1,97 1,75 1,67 1,44 1,26 1,11 0,92 0,78 0,75 0,70
406,4 3,2 2,48 2,25 2,01 1,91 1,65 1,46 1,28 1,06 0,90 0,85 0,79 0,77
457,0 3,2 2,25 2,05 1,84 1,75 1,52 1,34 1,19 0,99 0,84 0,79 0,74 0,72 0,66
508,0 4,0 2,65 2,43 2,20 2,08 1,82 1,62 1,44 1,20 1,02 0,95 0,88 0,84 0,77 0,77
610,0 5,0 2,92 2,71 2,47 2,34 2,07 1,86 1,66 1,40 1,20 1,10 1,02 0,96 0,88 0,86 0,82
711,0 5,0 2,56 2,39 2,19 2,08 1,85 1,66 1,50 1,27 1,09 1,00 0,93 0,88 0,80 0,79 0,74 0,66
813,0 6,3 2,95 2,77 2,56 2,44 2,19 1,99 1,80 1,54 1,34 1,22 1,14 1,06 0,97 0,94 0,86 0,77 0,76
914,0 8,0 3,46 3,27 3,05 2,92 2,65 2,42 2,21 1,91 1,67 1,52 1,42 1,32 1,21 1,15 1,05 0,93 0,89 0,89
1016,0 8,0 3,15 2,99 2,79 2,67 2,43 2,23 2,04 1,77 1,56 1,42 1,33 1,23 1,13 1,08 0,98 0,87 0,84 0,84 0,77
1220,0 10,0 3,40 3,25 3,07 2,95 2,72 2,52 2,33 2,05 1,81 1,66 1,56 1,45 1,34 1,27 1,14 1,02 0,96 0,94 0,86 0,82
Mondi Štětí a.s. STANDARD 13.02.08 Page: 28/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Table 3 Allowable pressure (MPa) for reinforced-branch connection See standard 13.01.06, item 2.2
Pipe class 16H
Outside Outside diameter of connecting pipe (mm)
diameter
main 26,9 33,7 42,4 48,3 60,3 76,1 88,9 114,3 139,7 168,3 219,1 273,0 323,9 355,6 406,4 457,0 508,0 610,0 711,0 813,0
pipe Wall 1,6 1,6 1,6 1,6 2,0 2,0 2,0 2,0 2,0 2,6 3,2 3,2 4,0 5,0 6,3 8,0 8,0 10,0 10,0 12,5
26,9 1,6 6,21
33,7 1,6 5,75 5,23
42,4 1,6 5,01 4,57 3,89
48,3 1,6 4,29 3,94 3,38 2,85
60,3 2,0 4,95 4,56 3,92 3,31 3,24
76,1 2,0 4,15 3,84 3,33 2,84 2,78 2,31
88,9 2,0 3,59 3,33 2,91 2,50 2,44 2,04 1,76
114,3 2,0 3,13 2,91 2,56 2,21 2,16 1,81 1,57 1,36
139,7 2,0 2,55 2,39 2,12 1,84 1,80 1,52 1,33 1,16 0,95
168,3 2,6 2,86 2,69 2,41 2,11 2,02 1,72 1,50 1,32 1,08 1,01
219,1 3,2 3,14 2,97 2,68 2,37 2,25 1,93 1,69 1,49 1,22 1,11 1,06
273,0 3,2 2,91 2,76 2,49 2,22 2,11 1,81 1,59 1,40 1,16 1,05 1,00 0,93
323,9 4,0 3,34 3,18 2,91 2,60 2,46 2,14 1,89 1,67 1,38 1,24 1,15 1,07 1,05
355,6 5,0 3,89 3,72 3,42 3,10 2,92 2,56 2,28 2,02 1,69 1,49 1,37 1,27 1,22 1,22
406,4 6,3 4,59 4,42 4,10 3,74 3,53 3,12 2,80 2,50 2,10 1,84 1,67 1,56 1,47 1,43 1,45
457,0 8,0 5,10 4,93 4,62 4,27 4,05 3,62 3,28 2,96 2,52 2,21 2,00 1,87 1,74 1,67 1,64 1,56
508,0 8,0 4,46 4,32 4,06 3,76 3,58 3,22 2,93 2,65 2,27 2,00 1,82 1,70 1,59 1,52 1,49 1,42 1,26
610,0 10,0 5,04 4,91 4,65 4,34 4,15 3,77 3,46 3,16 2,74 2,42 2,20 2,06 1,92 1,81 1,75 1,63 1,45 1,43
711,0 10,0 4,54 4,42 4,20 3,94 3,77 3,44 3,16 2,90 2,52 2,24 2,03 1,91 1,78 1,69 1,63 1,52 1,35 1,33 1,22
813,0 12,5 5,24 5,12 4,89 4,62 4,44 4,09 3,79 3,50 3,08 2,75 2,50 2,36 2,19 2,06 1,97 1,81 1,62 1,56 1,42 1,43
Mondi Štětí a.s. STANDARD 13.02.08 Page: 29/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Table 4 Allowable pressure (MPa) for reinforced-branch connection See standard 13.01.06, item 2.2
Pipe class 25H
Outside Outside diameter of connecting pipe (mm)
diameter
main 10,2 17,2 21,3 26,9 33,7 42,4 48,3 60,3 76,1 88,9 114,3 139,7 168,3 219,1 273,0 323,9 355,6 406,4 457,0
pipe Wall 1,6 1,6 1,6 1,6 1,6 2,0 2,0 2,0 2,6 3,2 4,0 5,0 5,0 6,3 8,0 10,0 12,5 12,5 12,5
10,2 1,6 8,41
17,2 1,6 7,33 6,21
21,3 1,6 6,74 5,75 5,23
26,9 1,6 5,82 5,01 4,57 3,89
33,7 1,6 4,94 4,29 3,94 3,38 2,85
42,4 2,0 5,67 4,95 4,56 3,92 3,31 3,24
48,3 2,0 4,72 4,15 3,84 3,33 2,84 2,78 2,31
60,3 2,0 4,05 3,59 3,33 2,91 2,50 2,44 2,04 1,76
76,1 2,6 4,63 4,15 3,87 3,41 2,95 2,82 2,36 2,04 1,95
88,9 3,2 4,72 4,27 4,02 3,58 3,13 2,96 2,51 2,17 2,03 1,81
114,3 4,0 5,04 4,62 4,37 3,94 3,49 3,28 2,80 2,45 2,26 1,97 1,81
139,7 5,0 5,59 5,18 4,93 4,49 4,01 3,77 3,26 2,87 2,61 2,25 2,04 1,95
168,3 5,0 5,16 4,79 4,57 4,17 3,74 3,52 3,05 2,69 2,46 2,13 1,92 1,84 1,72
219,1 6,3 5,94 5,56 5,33 4,91 4,45 4,19 3,67 3,26 2,97 2,55 2,27 2,13 1,98 1,96
273,0 8,0 6,96 6,56 6,32 5,88 5,38 5,07 4,49 4,03 3,66 3,15 2,78 2,57 2,39 2,31 2,31
323,9 10,0 8,07 7,66 7,41 6,94 6,41 6,07 5,43 4,91 4,47 3,86 3,40 3,10 2,90 2,75 2,69 2,71
355,6 12,5 8,69 8,32 8,09 7,65 7,13 6,79 6,15 5,62 5,16 4,49 3,97 3,61 3,39 3,18 3,06 3,01 2,86
406,4 12,5 7,55 7,25 7,06 6,70 6,27 5,99 5,45 5,01 4,61 4,04 3,59 3,28 3,08 2,89 2,79 2,74 2,60 2,32
457,0 12,5 6,67 6,42 6,26 5,96 5,60 5,36 4,90 4,51 4,17 3,67 3,28 3,00 2,82 2,66 2,56 2,52 2,39 2,14 1,94
Mondi Štětí a.s. STANDARD 13.02.08 Page: 30/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Table 5 Allowable pressure (MPa) for reinforced-branch connection See standard 13.01.06, item 2.2
Pipe class 40H
Outside Outside diameter of connecting pipe (mm)
diameter
main 10,2 17,2 21,3 26,9 33,7 42,4 48,3 60,3 76,1 88,9 114,3 139,7 168,3 219,1 273,0
pipe Wall 1,6 1,6 1,6 1,6 1,6 1,6 1,6 1,6 1,6 2,0 2,6 3,2 4,0 5,0 6,3
10,2 1,6 40,23
17,2 1,6 28,53 20,28
21,3 1,6 24,36 17,83 15,34
26,9 1,6 20,31 15,30 13,33 11,31
33,7 1,6 16,91 13,07 11,51 9,87 8,41
42,4 1,6 13,95 11,04 9,81 8,51 7,33 6,21
48,3 1,6 12,47 9,99 8,93 7,79 6,74 5,75 5,23
60,3 1,6 10,28 8,39 7,56 6,66 5,82 5,01 4,57 3,89
76,1 1,6 8,35 6,95 6,31 5,61 4,94 4,29 3,94 3,38 2,85
88,9 2,0 9,26 7,82 7,15 6,40 5,67 4,95 4,56 3,92 3,31 3,24
114,3 2,6 9,59 8,29 7,67 6,95 6,23 5,50 5,10 4,43 3,77 3,60 3,29
139,7 3,2 9,87 8,69 8,11 7,42 6,73 6,00 5,59 4,90 4,22 3,97 3,56 3,32
168,3 4,0 10,46 9,36 8,81 8,15 7,47 6,74 6,31 5,60 4,86 4,54 4,02 3,68 3,49
219,1 5,0 10,29 9,39 8,93 8,36 7,76 7,09 6,70 6,02 5,31 4,95 4,37 3,96 3,69 3,30
273,0 6,3 10,61 9,83 9,42 8,91 8,36 7,74 7,37 6,70 5,99 5,59 4,94 4,47 4,11 3,62 3,35
Mondi Štětí a.s. STANDARD 13.02.08 Page: 31/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Table 6 Allowable pressure (MPa) for reinforced-branch connection See standard 13.01.06, item 2.2
Pipe class 63H
Outside Outside diameter of connecting pipe (mm)
diameter
main 10,2 17,2 21,3 26,9 33,7 42,4 48,3 60,3 76,1 88,9 114,3 139,7 168,3
pipe Wall 1,6 1,6 1,6 1,6 1,6 1,6 1,6 2,0 2,6 3,2 4,0 5,0 6,3
10,2 1,6 40,23
17,2 1,6 28,53 20,28
21,3 1,6 24,36 17,83 15,34
26,9 1,6 20,31 15,30 13,33 11,31
33,7 1,6 16,91 13,07 11,51 9,87 8,41
42,4 1,6 13,95 11,04 9,81 8,51 7,33 6,21
48,3 1,6 12,47 9,99 8,93 7,79 6,74 5,75 5,23
60,3 2,0 13,07 10,71 9,66 8,51 7,43 6,38 5,83 5,44
76,1 2,6 13,84 11,63 10,61 9,47 8,36 7,26 6,66 6,08 5,65
88,9 3,2 14,90 12,75 11,73 10,56 9,41 8,25 7,60 6,88 6,27 6,06
114,3 4,0 14,95 13,10 12,20 11,14 10,06 8,95 8,31 7,50 6,78 6,44 5,84
139,7 5,0 15,68 14,01 13,17 12,16 11,12 10,01 9,37 8,47 7,62 7,17 6,40 6,01
168,3 6,3 16,76 15,24 14,45 13,49 12,47 11,36 10,71 9,74 8,76 8,20 7,26 6,70 6,38
8.2 Designation
Name, Reinforced branch connection, Do1/ Do2, s1/ s2, material, standard No.
Example: Reinforced branch connection, 168.3/114.3, 5.0/4.0, 1.4404, 13.02.08
Mondi Štětí a.s. STANDARD 13.02.09 Page: 32/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
9 Reinforced branch connection with plate 9.1 Dimensions
DN1 lpl
40 50 (65) 80
15 15 15 15
100 (125) 150 200
15 16 17 20
250 300 350 400
22 27 29 31
(450) 500 600
700
800
900
1000
1200
36 43
47
50
54
57
67
83
The wall thickness of the reinforcing plate must be minimum the wall thickness of the main pipe (s).
Mondi Štětí a.s. STANDARD 13.02.09 Page: 33/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
9.2 Designation
Name DN 1/ DN 2, material, standard No.
Example: Reinforced - branch connection, 200/ 25, 1.4404, 13.02.09
Mondi Štětí a.s. STANDARD 13.02.10 Page: 34/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
10 Blank flange 0H...25H
10.1 Dimensions
2 1 Plate Ø D1, s = 2 1.4404
1 1 Blank flange EN 1092-1
PN 10… PN 25
Type 05
P265GH
Hot dip galvanized
Part Pcs Description Dimension Material
Note: PN 10 shall be used for pipe classes OH…10H.
D1 is equal to flange facing diameter.
10.2 Designation
Name, DN, pressure class of pipe class, material of the flange, material of lining plate, standard No.
Example: Blank flange, DN 250, PN 16, P265GH, 1.4404, 13.02.11
Mondi Štětí a.s. STANDARD 13.02.11 Page: 35/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
11 Spade blank
11.1 General
Spade blank according to this standard shall be used between flanges instead of shut valve.
If the plate thickness s1 < 8 mm, the plate material is 1.4404.
When s1 > 8 mm, the material is P265GH, which has been lined with 1.4404.
Mondi Štětí a.s. STANDARD 13.02.11 Page: 36/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
DN
D
Plate thickness (mm) s
L B
Pressure difference, MPa
mm 0.1 MPa 0.25 MPa 0.4 MPa 0.6 MPa 1.0 MPa mm mm
15 47
1.6 1.6
20
20 58 1.6
25 68 1.6
2
(32) 78 1.6 2
75
40 88
50 102
2 3 3
30
(65) 122 2
4
80 133 3
3 4 5
100 158
4 5 6
(125) 184 2 4
5 6
150 212 4
8
200 268 5 6 8 9+3=12 100
250 320 6 8 9+3=12 11+3=14
300 370 8
8 10+3=13 12+3=15 50
350 430 5 9+3=12 12+3=15 15+3=18
400 482 6 8 11+3=14 13+3=16 17+3=20
500 585 8 10+3=13 13+3=16 16+3=19 20+3=23 150
600 685 8 12+3=15 15+3=18 19+3=22 24+3=27 75
800 905 10+3=13 15+3=18 19+3=22 23+3=26 29+3=32 85
Notes: 1. Carbon steel surface must be painted according to painting instructions. 2. One hole in handle for closed plate (two for open plate).
11.2 Designation
Name, DN, pressure difference, standard No.
Example: Spade blank, 150, 0.6, 13.02.12
Mondi Štětí a.s. STANDARD 13.02.12 Page: 37/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
12 Open spade
12.1 General
Open spade according to this standard shall be used between flanges when blind disc according to standard 02-009 has been removed.
12.2 Dimensions
Dimensions are in Table 1.
Mondi Štětí a.s. STANDARD 13.02.12 Page: 38/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
Table 1
Plate thickness (mm) s
L B
Pressure difference, MPa
DN D1
mm
D
mm
0.1 MPa 0.25 MPa 0.4 MPa 0.6 MPa 1.0 MPa mm mm
15 21 47 1.6
1.6 1.6
20
20 27 58 1.6
25 34 68 2
2
(32) 42 78 1.6
75
40 48 88 2
50 60 102
3 3
30
(65) 76 122 2
4
80 89 133
3 4 5
100 114 158 2
3 4 5 6
(125) 140 184 4 5 8
150 168 212
6
200 219 268 4 5 6 8 9+3=12 100
250 273 320 6 8 9+3=12 11+3=14
300 324 370 5 8 8 10+3=13 12+3=15 50
350 356 430 9+3=12 12+3=15 15+3=18
400 406 482 6 8 11+3=14 13+3=16 17+3=20
500 508 585 8 10+3=13 13+3=16 16+3=19 20+3=23 150
600 610 685 8 12+3=15 15+3=18 19+3=22 24+3=27 75
12.3 Material
When s1 < 8 mm, material is 1.4404, and when s1 > 8 mm, material is P265GH, or equal with 1.4404 lining.
Notes: 1. Carbon steel surface must be painted according to painting instructions.
2. Two holes in handle indicates open spade (one for spade blank)
12.4 Designation Name, DN, pressure difference, standard No. Example: Open spade, 250, 0.25, 13.02.13
Mondi Štětí a.s. STANDARD 13.02.13 Page: 39/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
13 Plate valve
13.1 General
Plate valve shall be used between flanges instead of shut valve.
13.2 Dimensions
DN 0H2...10H2
A mm
B mm
C mm
D mm
E mm
R mm
S mm
MPa
50 56 102 102 125 18 15 5 1.0 (65) 72 122 70 145 18 15 5 1.0 80 85 133 80 160 18 15 5 1.0 100 110 158 90 180 18 15 5 0.6 (125) 135 184 90 210 18 15 6 0.7 150 164 212 90 240 23 15 8 1.0 200 214 268 90 295 23 15 8 0.6 250 263 320 140 350 23 15 10 0.6 300 320 370 140 400 23 15 10 0.6 350 350 430 140 460 23 15 16 1.0 400 400 482 140 515 27 15 16 0.6 500 500 585 150 620 27 15 16 0.6 600 602 685 150 725 30 15 16 0.4
MPa indicates the maximum pressure difference over the plate. 13.4 Material
1.4404 according to EN 10028-7
Mondi Štětí a.s. STANDARD 13.02.13 Page: 40/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
13.5 Designation Name, DN, standard No. Example: Plate valve, DN 250, 13.02.14
Mondi Štětí a.s. STANDARD 13.02.14 Page: 41/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
14 Drain and spooling connection DN 40 and DN 50
14.1 Dimensions
DN 50
6 2 Flat bar Thickness 4.0 mm 1.4404
5 1 Pipe 60.3 x 1.6 13.02.03
4 1 Reinforcement ring Thickness 2.0 mm 1.4404
3 1 Bend 60 60.3 x 2.0 13.02.05
2 1 Hose coupling R 2” external thread ALSi1Mg
1 1 Valve DN 50 TH/ WE see valve spec.
Part Pcs Description Standard No. Material
DN 40
6 2 Flat bar Thickness 4.0 mm 1.4404
5 1 Pipe 48.3 x 1.6 13.02.03
4 1 Reinforcement ring Thickness 4.0 mm 1.4404
3 1 Bend 60 48.3 x 2.0 13.02.05
2 1 Hose coupling R 1 1/4“ external thread ALSi1Mg
1 1 Valve DN 40 TH/ WE see valve spec.
Part Pcs Description Standard No. Material
Mondi Štětí a.s. STANDARD 13.02.14 Page: 42/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
14.2 Designation
Name, DN, type, material, standard No.
Example: Drain connection, DN 50, A, 1.4404, 13.02.15
Mondi Štětí a.s. STANDARD 13.02.15 Page: 43/44
Version: 00 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
15 Vent connection DN 25
15.1 Dimensions
4 2 Flat bar 4.0 mm 1.4404
3 1 Hex head plug DN 25 EN 10241 1.4404 or equal
2 1 Valve DN 25, TH/ WE see valve specification
1 1 Pipe 33.7 x 1.6 EN 10217-7 1.4404
Part Pcs Description Standard No. Material
15.2 Designation
Name, DN, type, material, standard No.
Example: Vent connection, DN 25, A, 1.4404, 13.02.16
Mondi Štětí a.s. STANDARD 13.02.16 Page: 44/44
Version: 1 Valid from: 18.1.2018
Printouts, if any, are not controlled. Printed on: 23/01/2018
16 Sample taking connection DN 40 16.1 Dimensions
DN 40
6 1 Reinforcement plate 2) 1.4404
5 2 Flat bar 30 x 2 1.4404
4 1 Hose coupling R 1 1/2” int. thread AlSi1Mg 3)
3 1 Elbow 90° 48.3 x 2.0 13.02.05 1)
2 1 Valve DN 40 WE see valve spec.
1 1 Screwed end R 1 1/2” EN 10241 1.4404
Part Pcs Description Standard No. Material
Note: 1. Material and pipe parts according to each pipe class. 2. Thickness of the reinforcement ring = the wall thickness of the main pipe, min. 2 mm 3. Material 1.4404 in chemical lines.
16.2 Designation Name, material, standard No. Example: Sample taking connection, DN 40, 1.4404, 13.02.17