Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
1
FOR YOUR SAFE WORK AND CORRECT INSTALLATION
SPECIFICATIONS
●
●
FD30EX /50 HRP SLIDING DOOR SYSTEM
Effective open width( Door widthMiddle door
widthLast door
width height(Door
thickness( weightVertical
2 doors synchronized- -
mm
- mm
-7 mm mm
--
- mm-
2 doors synchronized-
----
WARNING: If not followed, death or serious injury may result.
Caution: If not followed injury or damage may result.
This (sliding door system) should be installed by a qualified person. If the system is not installed correctly, the door will not operate smoothly, and may cause injury.It is necessary to manufacture the frame with sufficient strength so that it endures the weight of the door and any impact upon opening/closing the door. Only use designated screws and ensure that they are fastened firmly. A frame with poor strength or loose screws might result in the door falling and causing injury.Do not try to use this product for anything other than its original purpose. Do not use any part for applications outside of its specification.Do not disassemble nor modify any parts other than those described in this document.
Make sure to follow the designated dimensions, specifications, and horizontal/vertical angles. Make sure that the frame is not warped, since it may affect the movement of the door.If cutting any parts, make sure to remove any burrs before installation. Also check the upper track for any left-over burrs or scraps and remove these.This product is a part for architectural fittings. After installation, make sure to test the finished product thoroughly to ensure that it is well-functioning and safe. Please inform the end user about general precautions and safety to prevent improper use.Make sure to check the screws for slack at regular intervals (one month from first usage, half a year, and then one time every year is recommended).
ProhibitedWarningCaution Required
Meaning of symbols
ABOUT THE PRODUCT
2
Trigger(Trigger Jig)
①
End stopper
Item
2 doors synchronized
3 doors synchronized
Door guide (door mount)
Door guide wall mount)
Block for bottom guide
Guide track Bumper blockSoft closer
(two-way)※1Soft closer(one-way)
② ③ ④ ⑤ ⑥
Cross recessed pan head tapping screws3.5×30…………………3 ea.
Cross recessed pan head tapping screws3.5×30…………………3 ea.
Cross recessed pan head tapping screws3.5×30…………………3 ea.
⑦ ⑧
Upper roller
⑨
Trigger ※1
FD30-HRGU FD30-HRDG FD30-HBGF FD30-HRDB FD30-HBDR1000 FD30-HBB FD30EX-WRH-DSC FD30EX-WRH-SC FD30-WRH-NFD30-TRGFD30-TRJ
⑩
L/R 1 ea 1pc 1pc 2 pcs1pc 1pc 1pc 1pc 2 pcs 2 pcs
L/R 2 ea 2 pcs 1pc 3 pcs1pc 2 pcs 1pc 2 pcs 3 pcs 3 pcs
⑫Upper track
(surface mount)
Item
2 doors synchronized
3 doors synchronized
Upper track(recessed mounted)
FD30-TRM FD30-TRH
Use 2 (surface mounted or recessed)
Use 3 (surface mounted or recessed)
1820mm - 4000mmHole pitch:300Pitch end :30mmRecommended screw :Countersunk head tapping screws 3.5×20
Item No.
Name
No.
Name
Item No.
No.
※ 1
Option
No. ⑫ ⑬ ⑭ ⑮ ⑯
Name Cover capDoor stopper
Floor guide Bottom guide Spanner
Item
COMPONENT PARTS
23.5 4021※2
33
1115
7
23.5※3 23.5※3
5 17
RH
13DH
=RH-
21.5
7 8.5 Operation door
18.5※
2
25 4320
7 73615
1111
25 25
5 17 1319
.57
RH
DW+DN+104.5
DH=R
H-39
.5
520.5
184.5Trigger (climping)
4 Process hole for trigger.4 Process hole for trigger.
Track length = FW
DW+DN-358
44849.5
45
24
Door pull(Sold separately)
7519
80
60
Opening width in frame FW
19
Effective opening width RO= RW- DNOperation door width = DW+ DN
Last door width= DW 81
Opening width RWMargin DN
DW= 3
DW
81FW+162-DN
7
Countersunk head tapping screw 3.5x20 (recommended)
In case of 33 mm thick door (recessed mounted track)
Countersunk head tapping screw 3.5x20 (recommended)
In case of 36 mm thick door (surface mounted track)
47.5
47.545
11
55
3 2
11
11
Last door
5
3 2
11
5
Last door
Operation door
106
7 9 98
10
897
69
43211
[1]Operation door
Leading edge Trailing edge
[2]Last door
※ 2 The dimension varies with the assembled direction of the guide block on the door guide ②③ (see section 10
3
[1]Operation door
Leading edge Trailing edge
[3]Last door
[2]Middle door
※ 2 The dimension varies with the assembled direction of the guide block on the door guide②③ (see section 10
⑫Cover cap
16
15
47.5
47
2
20
45
1645
47.5
17
1645
47.5
47
2
20
16
4547.5
17
15Operation door:DN+20Middle door :20
⑫Cover cap
4 Process hole for trigger.
4 Process hole for trigger.
4 Process hole for trigger.
Track length = FW
Last door
Middle door= DW Last door width= DW
23.5 4021 40
11
11
Middle door
Last door7 33
11
5
515115
3 52
223.5※3
23.5※3
13
23.5※3
18.5
7 8.5
Operation door
RH
Countersunk head tapping screw 3.5x20 (recommended)
DH=
RH‒2
1.5
In case of 33 mm thick door (recessed mounted track)
25 43 4320
11Countersunk head tapping screw 3.5x20 (recommended)
19.5
Middle door
Operation door7
RH
DH=
RH‒3
9.5
1713
5
5
7 77
36
1511
5
3 33
2525
3
252
2In case of 36 mm thick door (surface mounted track)
7 9
DW×2+DN+24.5DW+DN+104.5
Trigger (climping)184.5
76
531
47.5
45
6
8108
10
10
9DW+DN‒358
49.5450
98 6
47.5
45 9 8 9
Door pull(Sold separately)
80
601921
60
1
80
1921
24
75193 4
Opening width in frame FWOpening width RW
8080
Operation door width DW+DNEffective opening width RO=RW‒DN Margin DN
DW
80DW= 4
FW+240‒DN
77
6
4
①
End stopper
Item
2 doors synchronized
3 doors synchronized
Door guide (door mount)
Door guide (wall mount)
Block for bottom guide
Recessed guide track under door
Soft closer(one-way)※1Stopper block
Soft closer(two-way)※1
② ③ ④ ⑤ ⑥
Flat fillister head tapping screw3.8×40…………………3pcs
Flat fillister head tapping screw3.8×40…………………3pcs
Flat fillister head tapping screw3.8×40…………………3 pcs
Countersunk 6 head tapping screw4×30……………………4 pcs
⑦ ⑧
Upper roller
⑨
Trigger ※1
FD30-HRGU FD30-HRDG FD30-HBGF FD30-HRDB FD30-HBRT1500SIL FD50-HSB FD50-WRH-DSC FD50-WRH-DSC FD50-WRH FD50-TRG
⑩
L/R 1 ea 1pc 1pc 2 pcs1pc 1pc 1pc 1pc 2 pcs 3 pcs
L/R 2 ea 2 pcs 1pc 3 pcs1pc 2 pcs 1pc 2 pcs 3 pcs 4 pcs
⑪
Upper track
Item
2 doors synchronized
3 doors synchronized
FD50 TRM
⑫FD50-H
Cover cap
FD50-WRH-C
2 pcs
3 pcs
4 pcs
6 pcs
Hole pitch : 300 mmPitch end : 30 mmAccessory screw:Flat fillister pan head tapping screw 3.8x40
Item No.
Name
No.
Name
Item No.
No.
Trigger(Trigger Jig)
Hole pitch: 250 mmPitch end : 30 mmRecommended screw:Countersunk head tapping screw 4×20
(various sizes)
Option
No. ⑬ ⑭ ⑮ ⑯
NameDoor stopper
Floor guide S Bottom guide Spanner
Item
COMPONENT PARTS
[1]Operation door
Leading edge Trailing edge
[2]Last door
※ The dimension varies with the assembled direction of the guide block on the door guide ②③ (see section 10
Jump prevention nut (12 mm)
Trigger (climping)
Door pull(Sold separately)
DW+DN‒412
Trigger (climping)
215 18
592.5
33
3349
Operation door width=DW+DN Last door width=DW
Margin DWDW
DW= FW+162‒DN
Opening width in frame FWOpening width RW
Effective opening width RO=RW–DN
23.5 4028
Last door
Operation door
9
RH
25
10D
H=
RH‒2
3131
7
73371511
23.5※3
5
23.5※3
In case of 33 mm thick door (recessed mounted track)
25 4328Last
door
36 771511
2525
5 17 13
Operation door259
DH=
RH‒4
7
RH
In case of 36 mm thick door (surface mounted track)
2× 5 Process hole for trigger.
DW+DN+135 18
2× 5 Process hole for trigger.
Track length = FW
18
21 8.5 48
30
2× 5 Process hole for trigger.
3
5 5
2
5
3
5
2
7
6
9 8 9
5
89
7 11 9
1 12
60
24
19
75193 4
81 81 3
5
48+
1 0
15
2
20
⑫Cover cap
2
20
15
16+10
49+10
49+1016+10
48+
1 0
51+10
16+10
16+
1 0 49+10
16+10
48+
1 0
51+10
⑫Cover cap
1717
Operation door:DN+20Middle door :20
49+10
[1]Operation door
Leading edge Trailing edge
[3]Last door
[2]Middle door
※ The dimension varies with the assembled direction of the guide block on the door guide ②③ (see section 10
Operation door width=DW+DNLast door width=DW
In case of 33 mm thick door(recessed mounted track)
Middle door=DWMargin DN
DW= 4
DW
FW+240‒DN
Operation door
Last door
Last door
Operation door
Opening width in frame FWOpening width RW
Effective opening width RO=RW–DN
2× 5 Process hole for trigger.
DW×2+DN+55DW+DN+135
2× 5 Process hole for trigger.2× 5 Process hole for trigger.
Track length = FW
Jump prevention nut (12 mm)
Trigger (climping)Door pull(Sold separately)
30
Last door
Last door
Trigger (climping)
2× 5 Process hole for trigger.
23.5※323.5※3 23.5※3
43432528
3671511
2525
25
77
40 4023.528
7 33 7
1511
259 10
RH
DH=R
H-23
5 17 13
9 25
RH
DH=R
H-47
5 17 13
15.2 48
80 80 80
18215
33
3349 2
148
8.5
592.5
15.2
48 60
15.2
7
5
3
2
2
2
2
9 7 9
3 4
5
5
5
3
5
5
2
In case of 36 mm thick door (surface mounted track)
1 1
7 6 97
6
14.4 6
9
18
8 18DW+DN‒412
710
79
6
2 1
19.2
6
4 DW-358+DN (Margin)30
4.8 7.8 CSK
4.8 7.8 CSK
304DW+104.5+DN (Margin)
30
DW-358+DN (Margin)4
4.8 7.8 CSK
4
4.8 7.8 CSK
DW+104.5+DN (Margin) 30
4
4.8 7.8 CSK
30
2× 5
21518
DW×2+24.5+DN (Margin)
18
2× 5
DW-412+DN (Margin)
304.5
4.5 3018DW+135+DN (Margin)
2× 5
2× 5
21518
DW‒412+DN (Margin)
18 304.5
2× 5
DW+135+DN (Margin)18 4.5 30
2× 5
DW×2+55+DN (Margin)2× 5 18 4.5 30
Leading edge has
Leading edge has
Trigger (climping)(FD30EX only)
ASSEMBLY
1
Remove any dirt or aluminum chips
2
〈 〉
〈 〉
〈 〉
〈 〉
7
3
4 5
4Fasten the casing firmly with attached screws.Recessed roller: Separate main unit from casing.
❶
❷Main unitPull out casing.
Pull up lever.
Casing
33
33
36
36
33
Guide block
Thick Thin Thick Thin
Door thickness Marking
8
Guide track length of operation door = DW-60-DN Guide track length of operation door = DW-60-DN)
Guide track length of last door = DW-36 Guide track length of middle door = DW-60
Guide track length of last door = DW-36
DoorDoorCorner-align
〈 〉
Leading edge Leading edgeTrailing edge Trailing edge
〈 〉
〈 〉
〈 〉
〈 〉
〈 〉
〈 〉
①End stopper(With screws)
②(With screws)
⑤
④Block for bottom guide (With screws)
Face the strips of the end stoppers to the
Take care of the mounting direction of end stoppers ①
Fit the door guide to the bottom end of
6
⑤
①
⑤
②
①
②
①
⑤
①
⑤
①
9⑩Trigger, 3 pcs
⑩Trigger, 3 pcs(Screws provided)
⑩Trigger, 4 pcs(Screws provided)
⑩Trigger, 2 pcs
〈 〉 〈 〉
[2]
[1]
7
9Fix trigger to the hole made during procedure 2.
8
×
Correct set position
Incorrect set position
Trigger catcher(Red colored Part)
Correct set position
If the position is wrong, pull back the trigger catcher to the correct position using a 6mm diameter hard bar.
Trigger catcher(Red colored Part)
6
FD30EX Soft closer(one-way)⑦or
FD50 Soft closer(two-way)⑧FD30EX Soft closer(one-way)⑦
orFD50 Soft closer(two-way)⑧
Upper roller⑨
FD30 Bumper block⑥or
FD50 Stopper block⑥
FD30 Bumper block⑥or
FD50 Stopper block⑥
Soft closer(two-way)⑦
Upper track⑪ ⑪
⑦
⑨
〈 〉 〈 〉
[3]
[2]
[1][2]
[1]
〈 〉 〈 〉
[2]
[1]
[3][2]
[1] [2]
[1]
[3]
10
Thick 33 36Thin Thick Thin
530~ 3435~ 38
Door thickness Marking3336
10< >
Mount the guide to the bottom of
11【1】 Order of hanging
Hang the doors in order from ① to ③
12
21
12
3
〈 〉
〈 〉右
上下
左
OK
×
上下
上下
Upper roller
Casing
Lever
Lever
Lever
【2】 Hanging 【3】 Insert the upper roller into the casing
Verify that the main unit is not
右
上下
左
15 19Door (leading edge)
【1】 Door guide ③❶ Fasten the base plate with
【2】 Floor guide ⑭
❷ Insert the guide block according to the table and
< >Mount the guide to the bottom of
DoorFrame
Door⑮Mounting Bottom Guide
(optional)
Frame
⑮Mounting Bottom Guide (optional)
11
5
15 Fastening the Jump Prevention NutThe jump prevention nut is on the hanger bolt of the recessed roller. Tighten the nut with the provided spanner until it contacts the soft closer.
Jump prevention nut
Tightening
Be sure to tighten the nut to prevent damaging parts.
5 13 5 5 13
右
上下
左右
上下
左
±2Clockwise=RaiseCounterclockwise=Lower
3 mm4 mm
13
[1]Operation door [1]Operation door
[2]Last door [2]Middle door
[3]Last door
< > 〈 〉
Leading edge
Closed position
Bumper block
Trigger Trigger
Trailing edge
Closed position
Closed positionClosed position
Frame or closed position
13【 】
【2】 Close the door slowly and check that the soft clos
【 】veri
【 】 Please refer to the "Troubleshooting" section when the soft closer does not
【5】block and stopper block in the track so that the position is realized as shown in
13
14【1】
【2】 [1]
【3】 [2], [3]:
15
Frame
Leading edge Leading edge Trailing edge
[2]
[2]
[1] [1][3]
12
TROUBLESHOOTINGTrouble Check Point Solution
Door stops during soft closing
No soft closing
The position of the trigger catcher may become
Abnormal noise during operation
Heavy door operation
PERIODICAL INSPECTION ・・
SUGATSUNE KOGYO CO.,LTD Tokyo, JAPANPhone: +81 (0)3 3866 2260 E-mail:[email protected] KOGYO (UK) LTD Reading, UKPhone: +44 118 9272 955 E-mail:[email protected] EUROPE GmbH Dusseldorf, GERMANYPhone: +49 211 53812900 E-mail:[email protected]
SUGATSUNE SHANGHAI Co., LTD Shanghai, CHINAPhone: +86 21 3632 1858 E-mail:[email protected], CHINA Phone: +86 20 6639 3552 E-mail:[email protected]
SUGATSUNE KOGYO INDIA PRIVATE LIMITED Mumbai, INDIAPhone: +91 22 28314490/91 E-mail:[email protected]
SUGATSUNE AMERICA, INC California, USAPhone: +1 310 329 6373 E-mail:[email protected], USA Phone: +1 312 461 1081 E-mail:[email protected].
SUGATSUNE CANADA, INC. Phone: +1 514 312 5267 E-mail:[email protected]
2019.04 1302-1
Door stopper (floor)
Then pull out the upper roller main unit from the door while When a
Spanner
Lever