123035430 How to Configure RPA

Embed Size (px)

Citation preview

  • 8/13/2019 123035430 How to Configure RPA

    1/9

    How-To Generate and Collect NAR Data fromVNX Arrays

    Login to the Unisphere console Select the array you want to collect data from

    Click on the System tab, then click on Monitoring and Alerts

    Click on Statistics for Block

    http://calfo.files.wordpress.com/2011/12/22.jpghttp://calfo.files.wordpress.com/2011/12/17.jpghttp://calfo.files.wordpress.com/2011/12/22.jpghttp://calfo.files.wordpress.com/2011/12/17.jpg
  • 8/13/2019 123035430 How to Configure RPA

    2/9

    Click on Performance Data Logging

    A Data Logging windows will appear. Configure the settings to match the screenshot below. Leave the Archive Intervalset to 600 seconds unless otherwise requested EMC or your EMC Reseller. Once the settings match click on START.

    http://calfo.files.wordpress.com/2011/12/41.jpghttp://calfo.files.wordpress.com/2011/12/31.jpghttp://calfo.files.wordpress.com/2011/12/41.jpghttp://calfo.files.wordpress.com/2011/12/31.jpg
  • 8/13/2019 123035430 How to Configure RPA

    3/9

    Confirm that you wish to continue by clicking YES.

    Confirm again that you want to apply these new settings by clicking YES.

    http://calfo.files.wordpress.com/2011/12/71.jpghttp://calfo.files.wordpress.com/2011/12/61.jpghttp://calfo.files.wordpress.com/2011/12/51.jpghttp://calfo.files.wordpress.com/2011/12/71.jpghttp://calfo.files.wordpress.com/2011/12/61.jpghttp://calfo.files.wordpress.com/2011/12/51.jpghttp://calfo.files.wordpress.com/2011/12/71.jpghttp://calfo.files.wordpress.com/2011/12/61.jpghttp://calfo.files.wordpress.com/2011/12/51.jpg
  • 8/13/2019 123035430 How to Configure RPA

    4/9

    Click YES yet again to confirm the data logging warning.

    Click OK to confirm (finally) that the operation was successful.

    You will be returned to the Data Loggin settings window. Click OK to close the window.

    http://calfo.files.wordpress.com/2011/12/91.jpghttp://calfo.files.wordpress.com/2011/12/82.jpghttp://calfo.files.wordpress.com/2011/12/91.jpghttp://calfo.files.wordpress.com/2011/12/82.jpg
  • 8/13/2019 123035430 How to Configure RPA

    5/9

    You will now need to let the data collection run for the specified time periodin this case 3 days.Retrieving NAR File for VNX from the GUI

    Now that the NAR data collection process has run for 3 days you will need to retrieve the NAR/NAZ files. Login to the Unisphere console Select the array you want to collect data from

    Click on the System tab, then click on Monitoring and Alerts

    http://calfo.files.wordpress.com/2011/12/18.jpghttp://calfo.files.wordpress.com/2011/12/101.jpghttp://calfo.files.wordpress.com/2011/12/18.jpghttp://calfo.files.wordpress.com/2011/12/101.jpg
  • 8/13/2019 123035430 How to Configure RPA

    6/9

    Click on Statistics for Block

    On the right, click on Retrieve Archive.

    http://calfo.files.wordpress.com/2011/12/32.jpghttp://calfo.files.wordpress.com/2011/12/23.jpghttp://calfo.files.wordpress.com/2011/12/32.jpghttp://calfo.files.wordpress.com/2011/12/23.jpg
  • 8/13/2019 123035430 How to Configure RPA

    7/9

    In the Retrieve Archives window, select your array and choose SPA. (NAR files are ONLY needed for ONE of the SPs) Change the Save File(s) As: destination to a location that is easy to locate. Highlight the .NAR or .NAZ (if encrypted) files that correspond to the 3 days you collected data for. The time may be off a

    little but this will not matter. There will probably be 46 files total.

    Click the Retreive button

    http://calfo.files.wordpress.com/2011/12/114.jpg
  • 8/13/2019 123035430 How to Configure RPA

    8/9

    Click YES to confirm the retrieval in the Confirm: Retrieve Archives window.

    At the bottom of the Retrieve Archives window verify that the files complete this may take a few seconds. Click Done

    http://calfo.files.wordpress.com/2011/12/131.jpghttp://calfo.files.wordpress.com/2011/12/122.jpghttp://calfo.files.wordpress.com/2011/12/131.jpghttp://calfo.files.wordpress.com/2011/12/122.jpg
  • 8/13/2019 123035430 How to Configure RPA

    9/9

    Go to the destination folder where you retrieved the files to.

    Upload all the files to EMC or your EMC Reseller as instructed.

    http://calfo.files.wordpress.com/2011/12/151.jpghttp://calfo.files.wordpress.com/2011/12/141.jpghttp://calfo.files.wordpress.com/2011/12/151.jpghttp://calfo.files.wordpress.com/2011/12/141.jpg