11-Rubber & Plastics

MALAYSIAN STANDARDS

SECTORIAL CATALOGUE

2007

No. 11

RUBBER & PLASTICS INDUSTRIES

Department of Standards Malaysia

Ministry of Science, Technology & Innovation

Level 1 & 2, Block C4, Complex C

Federal Government Administrative Centre

62502 Putrajaya, MALAYSIA

Tel : 603-8885 8000

Fax : 603-8888 5060E-Mail : [email protected]

http://www.standardsmalaysia.gov.my

INTRODUCTION

The Department of Standards Malaysia (Standards Malaysia) is the national standardisation and

accreditation body.

The main function of the Department is to foster and promote standards, standardisation and

accreditation as a means of advancing the national economy, promoting industrial efficiency and

development, benefiting the health and safety of the public, protecting the consumers, facilitating

domestic and international trade and furthering international cooperation in relation to standards and

standardisation.

Malaysian Standards are developed through consensus by committees which comprise of balanced

representation of producers, users, consumers and others with relevant interests, as may be appropriate

to the subject in hand. These standards where appropriate are adoption of international standards.

Approval of a standard as a Malaysian Standard is governed by the Standards of Malaysia Act 1996

(Act 549). Malaysian Standards are reviewed periodically. The use of Malaysian Standard is voluntary

except in so far as they are made mandatory by regulatory authorities by means of regulations, local

by-laws or any other similar ways.

The Department of Standards Malaysia appoints SIRIM Berhad as the agent to develop Malaysian

Standards.

The Industry Standards Committees (ISCs) established by SIRIM Berhad are responsible for the

development of Malaysian Standards in their respective areas, as follows:

ISC A - Food and Agriculture

ISC B - Chemicals and Materials

ISC C - Consumer Products, Personal Safety and Services

ISC D - Building and Civil Engineering

ISC E - Electrotechnical

ISC F - Mechanical Engineering

ISC G - Information Technology, Communications and Multimedia

ISC H - Petroleum and Gas

ISC J - Plastics and Plastics Products

ISC K - Packaging and Distribution

ISC L - Road Vehicles

ISC M - Fire Safety and Prevention

ISC N - Rubber and Rubber Products

ISC W - Occupational Health and Safety

NC Y - Quality Management and Quality Assurance

NC Z - Environmental Standards

More than 100 standards development committees involving more than 1500 individuals, have been

established under the ISCs.

(ii)

(iii)

ABBREVIATIONS

MS : Malaysian Standard

MS ISO : Malaysian Standard which is identical to International Organization for

Standardization (ISO) Standard. The numbering of the standard is identical to that

of the ISO Standard except for the prefix.

MS ISO/IEC : Malaysian Standard which is identical to the Joint ISO and IEC Standard. The

numbering of the standard is identical to that of the ISO/IEC Standard except for

the prefix.

MS.....(P) : Provisional Standard

Malaysian Standard which is adopted/adapted from international, regional or foreign national standard

without undergoing standards development committee deliberations due to its urgent need, as iden-

tified by the Department of Standards Malaysia. Provisional Standards are identified by a letter “P”

following the MS number.

Malaysian Standards Sectorial Catalogue 2007

This sectorial catalogue lists as at September 2007, Malaysian Standards that have been established

on product specifications, codes of practice, terminologies, guides and method of test on selected

sectors.

New standards, revisions, amendments, addenda, errata and reconfirmed standards as well as

standards that have been withdrawn are published bi-monthly in the SIRIM Berhad’s newsletter

Standards and Quality News.

An online system is available for searching and online purchasing. Payment can be made by credit

card. The system is called the MS Online System and can be accessed at http://www.msonline.gov.my.

The MS Online system contains over 4,000 Malaysian standards on all sectors.

List of Sectorial Catalogue 2007

1. Quality Management System, Environmental Management System & Safety and Health Protection

2. Health Care Technology, Metrology and Measurement. Testing

3. Mechanical and Fluid System and Components. Manufacturing Engineering, Energy and Heat

Transfer Engineering

4. Electrical Engineering & Electronics

5. Telecommunication, Information Technology. Office Equipment

6. Road Vehicles Engineering, Material Handling Equipment, Packaging & Distribution of Goods.

7. Textile and Leather Technology and Clothing Industry

8. Agriculture and Food Technology

9. Chemical Technology, Mining and Minerals, Petroleum and related technology & Metallurgy

10. Wood Technology, Glass & Ceramics Industries, Paper Technology and Paints & Colour Industries

11. Rubber & Plastics Industries

12. Constructions Materials & Building. Civil Engineering. Housekeeping. Entertainment. Sports.

(iii)

SUBJECT STRUCTURE ACCORDING TO

INTERNATIONAL CLASSIFICATION OF STANDARDS

(iv)

01. Generalities. Terminologies. Standardization

03. Sociology. Services. Company Organization

and Management. Administration. Transport.

07. Mathematics. Natural Sciences.

11. Health Care Technology.

13. Environment. Health Protection. Safety

17. Metrology and Measurement. Physical

Phenomena

19. Testing.

21. Mechanical Systems and Components for

General Use.

23. Fluid Systems and Components for General

Use.

25. Manufacturing Engineering.

27. Energy and Heat Transfer Engineering.

31. Electronics.

33. Telecommunications. Audio and Video

Engineering.

35. Information Technology. Office Machines.

37. Image Technology.

39. Precision Mechanics. Jewellery.

43. Road Vehicles Engineering.

45. Railway Engineering.

47. Shipbuilding and Marine Structures.

49. Aircraft and Space Vehicle Engineering.

53. Materials Handling Equipment.

55. Packaging and Distribution of Goods.

59. Textile and Leather Technology.

61. Clothing Industry.

65. Agriculture.

67. Food Technology.

71. Chemical Technology.

73. Mining and Minerals.

75. Petroleum and Related Technologies.

77. Metallurgy.

79. Wood Technology.

81. Glass and Ceramics Industries.

83. Rubber and Plastics Industries.

85. Paper Technology.

87. Paint and Colour Industries.

91. Construction Materials and Building.

93. Civil Engineering.

95. Military Engineering.

97. Domestics and Commercial Equipment.

Entertainment. Sports.

CONTENTS

Page

Introduction ------------------------------------------------------------------------------------------------------------------------ (ii)

Malaysian Standards Sectorial Catalogue ----------------------------------------------------------------------------- (iii)

Abbreviation ----------------------------------------------------------------------------------------------------------------------- (iii)

Subject Structure by ICS ----------------------------------------------------------------------------------------------------- (iv)

RUBBER & PLASTICS INDUSTRIES

Manufacturing processes in the rubber and plastics industries ------------------------------------------ 1

Raw materials for rubber and plastics in general ------------------------------------------------------------ 1

Latex and raw rubber ----------------------------------------------------------------------------------------------- 1

Rubber compounding ingredients ------------------------------------------------------------------------------- 3

Auxiliary materials and additives for plastics ----------------------------------------------------------------- 3

Rubber ------------------------------------------------------------------------------------------------------------------ 3

Plastics ----------------------------------------------------------------------------------------------------------------- 8

Plastics in general --------------------------------------------------------------------------------------------------- 9

Thermosetting materials ------------------------------------------------------------------------------------------- 15

Thermoplastic materials -------------------------------------------------------------------------------------------- 16

Cellular materials ---------------------------------------------------------------------------------------------------- 18

Reinforced Plastic --------------------------------------------------------------------------------------------------- 19

Rubber and plastic products -------------------------------------------------------------------------------------- 20

Rubber and plastics products in general ---------------------------------------------------------------------- 20

Films and sheets ----------------------------------------------------------------------------------------------------- 22

Plastics pipes, fittings and valves ------------------------------------------------------------------------------- 28

Hoses ------------------------------------------------------------------------------------------------------------------ 26

Seals -------------------------------------------------------------------------------------------------------------------- 27

Other rubber and plastic products ------------------------------------------------------------------------------- 27

Tyres -------------------------------------------------------------------------------------------------------------------- 28

Road vehicle tyres --------------------------------------------------------------------------------------------------- 29

Adhesives -------------------------------------------------------------------------------------------------------------- 30

Equipment for rubber and plastics industries ---------------------------------------------------------------- 31

Numerical Listing ---------------------------------------------------------------------------------------------------- 32

Index -------------------------------------------------------------------------------------------------------------------- 36

Order Form ------------------------------------------------------------------------------------------------------------ 42

(v)

1

83. RUBBER AND PLASTICS INDUSTRIES

83.020 Manufacturing processes in the

rubber and plastics industries

MS 1010 : 1986

Specification for rigid polyvinyl chloride and related plastic

pipe and fitting compounds.

Price RM30

83.040.01 Raw materials for rubber and

plastics in general

MS 506 : 1977 (2004)

Specification for ammonia (anhydrous and aqueous).

Covers grade of materials used as anti-coagulant for fresh natural

latex, and as a long term preservative for natural rubber latex

concentrates.

Price RM20

83.040.10 Latex and raw rubber

MS 281 : Part 1 : 1999

Natural rubber latex concentrate : Part 1 : Methods of sampling

(Third revision)

Specifies procedures for the sampling of natural rubber latex

concentrate. It is suitable for the sampling of latex concentrates that

is contained in drums, crates, bags and tanks. This standard is

technically equivalent to ISO 123 : 1985 except for the inclusion of

the closed-head type drum in the manual process of homogenising

latex concentrate. It supersedes MS 281 : Part 1 : 1992.

Price RM10

MS 281 : Part 2 : 1998

Specification for natural rubber latex concentrate. Part 2:

Determination of total solid content (Third revision).

This Malaysian Standard specifies a method for the determination

of the total solids content of natural rubber latex concentrate.

Price RM10

MS 281 : Part 3 : 1998

Specification for natural rubber latex concentrate : Part 3 :

Determination of dry rubber content (Third revision).

This Malaysian Standard specifies a method for the determination of

the dry rubber content of natural rubber latex concentrate.

Price RM10

MS 281 : Part 4 : 1999

Natural rubber latex concentrate : Part 4 : Determination of

alkalinity (Third revision)

Specifies a method for the determination of the alkalinity of natural

rubber latex concentrate. This standard is technically equivalent to

ISO 125 : 1995 and its supersedes MS 281: Part 4 : 1992.

Price RM10

MS 281 : Part 5 : 1998


Determination of mechanical stability (Third revision).


of the mechanical stability of natural rubber latex concentrate.

Price RM10

MS 281 : Part 6 : 1998

Specification for natural rubber latex concentrate (Includ-

ing raw natural rubber) : Part 6 : Determination of coagulum

content (Third revision).


of the coagulum content (sieve residue) of the natural rubber latex

concentrate.

Price RM10

MS 281 : Part 10 : 1999


volatile fatty acid number (Third revision).

Specifies a method for the determination of the volatile fatty acid

number of natural rubber latex concentrate. This standard is

technically equivalent to ISO 506 : 1992 except that kneading is

carried out using a glass rod and beaker whilst in the ISO standard,

kneading is carried out using a mortar and pestle and the end point

for titration is defined whereas it is not stated in the ISO standard.

It supersedes MS 281 : Part 10 : 1992.

Price RM10

MS 281 : Part 11 : 1999


Determination of KOH number (Third revision).

Specifies a method for the determination of the KOH number of

natural rubber latex concentrate. This standard is technically

equivalent to ISO 127 : 1995 and it supersedes MS 281 : Part 11 :

1992.

Price RM10

MS 281 : Part 12 : 2001

Natural rubber latex concentrate - Determination of boric

acid content (Third revision)

This Malaysian Standard specifies a procedure for the determination

of boric acid in natural rubber latex concentrate. The procedure is

not necessarily suitable for latices from natural sources other than

Hevea brasiliensis or for latices of synthetic rubber, compounded

latex, vulcanized latex or artificial dispersions of rubber. This

standard supersedes MS 281 : Part 12 : 1992.

Price RM10

MS 281 : Part 14 : 2001

Rubber, raw natural, and rubber latex, natural -

Determination of nitrogen content (Third revision)

This Malaysian Standard specifies a macro-method and a semi-

micro method for the determination of nitrogen in raw natural rubber

and in natural rubber latex using variants of the Kjeldahl process.

This standard supersedes MS 281: Part 14: 1993.

Price RM20

Best Seller

2

under diffuse daylight illumination against a matt white background

and comparison slide containing standard calibrated colour glasses

are used.

Price RM10

MS 1359 : Part 6 : 1994

Test methods for technically specified raw natural rubber

: Part 6 : Determination of rapid plasticity and plasticity re-

tention index.


of initial rapid plasticity and plasticity retention index of rubber. The

oxidation behaviour of raw natural rubber may have an important

bearing on processing behaviour and end product performance

and the plastic retention index test afford a convenient means of

characterising rubber in certain aspects.

Price RM10

MS 1359 : Part 7 : 1995


: Part 7 : Determination of mooney accelerated storage

hardening test (MASHT).

This Malaysian Standard specifies a method of measuring the storage

hardening raw natural rubber using the Mooney shearing disc

viscometer. In this test, accelerated storage-hardening is achieved

by storing rubber portions over phosphorus pentoxide in a vacuum

at 60°C ± 1°C for 48 ± 0.1h. The resultant increase in viscosity (Dv)

represents the accelerated storage-hardening.

Price RM10

MS 1359 : Part 8 : 1995


: Part 8 : Determination of wallace accelerated storage

hardening test (WASHT).

This Malaysian Standard specifies a method of measuring the

accelerated storage hardening of raw natural rubber suing the

wallace plastimeter. The test involves measurement of the plasticity

of standard pellets before and after a short period of storage under

conditions which accelerate the storage hardening reaction.

Price RM10

MS 1392 : 1998

Test method for the analysis of extractable proteins in

natural rubber products.

This Malaysian Standard provides an analytical test method for

determining the quantity of total extractable proteins in natural rubber

(NR) products. The test comprises essentially four parts namely:

a) sample preparation,

b) protein extraction,

c) protein precipitation and,

d) colourimetric assay.

The protein content is then determined by using Lowry microassay.

This standard is intended to supersede the Provisional Malaysian

Standard MS 1392 : 1996(P).

Price RM10 Amendment 1 : 2001

MS 1541 : 2002

Rubber latex, natural, concentrate - Determination of sludge

content


of the sludge content of natural rubber latex concentrate. The

method is not necessarily suitable for latices from natural sources

other than Heavea brasiliensis. It is not suitable for compounded

latex or vulcanized latex.

Price RM10

MS 1542 : 2002

Rubber, raw natural - Determination of dirt content


of the dirt content of raw natural rubber. It is not applicable to dirt

present as surface contamination. This standard supersedes MS

1359 : Part 3 : 1994. Price RM20

MS 281: Part 15: 1992

Specification for natural rubber latex concentrate: Part 15:

determination of viscosity (Second revision)


of the viscosity of natural rubber latex concentrate.

Price RM10

MS 281 : Part 16 : 1999


ph (Third revision)

Specifies a method for the determination of the pH of natural rubber

latex concentrate. This standard is technically equivalent to ISO

976: 1996 and it supersedes MS 281: Part 16: 1992.

Price RM10

MS 297: 1981

Specification for raw natural rubber (First revision)

Specifies minimum quality requirements for various grades. Tests in

accordance with MS 298.

Price RM10

MS 298 : 1985

Methods of sampling and test for raw natural rubber (First

revision).

Test methods are provided for the determination of dirt, volatile

matter, nitrogen, ash, rapid plasticity and plasticity retention, index,

colour, Mooney viscosity, accelerated and storage hardening test

(ASHT), acetone extract, vulcanisation characteristics (MOD) and

curing characteristics with the oscillating disk curement.

Price RM50

MS 317 : 1986

Specification for evaporated preserved natural rubber

latices (First revision).

Covers requirements for NR latex, type HA evaporated; NR latex,

type KHS evaporated; NR latex, type KLS evaporated.

Price RM10

MS 466 : 1987

Methods of sampling and testing field latex (First revision).

Test methods applicable to fluid field latex preserved with any of

the following (or suitable combinations): ammonia; potassium

hydroxide; sodium sulphate; formaldehyde; and boric acid.

Price RM20

MS 1157 : Part 41 : 1999

Methods of test for vulcanized rubber : Part 41 :

Determination of temperature rise and resistance to fatigue

in compression flexometer testing

Specifies the compression flexometer test for the determination of

the temperature rise and resistance to fatigue of vulcanized rubbers.

The flexometer specified is known as the Goodrich flexometer, but

any other apparatus giving equivalent performance may be used.

Price RM20

MS 1359 : Part 4 : 1994


: Part 4 : Determination of mooney viscosity.


of Mooney Viscosity of rubber using a shearing-disc Mooney

Viscometer. The torque necessary to rotate the disc in a cylindrical

chamber filled with rubber under specified conditions is determined

and the number proportional to this torque is taken as the viscosity

of the rubber.

Price RM10

MS 1359 : Part 5 : 1994


: Part 5 : Determination of colour.


of Lovibond Colour index of rubber. Colour matching is carried out

MS 1549 : 2002

Test method for determination of residual powder on power free

rubber medical gloves

This Malaysian Standard is designed to determine the amount of

residual power (or filter-retained mass) found on gloves described

as non powdered, powder free, powderless, no powder, or other words

to that effect. The test method covers the determination of average

powder or filter-retained mass found on a sample of medical gloves.

Price RM10

MS 1550 : 2002

Test method for determination of residual powder on powdered

rubber medical gloves

This Malaysian Standard is designed to determine the amount of

residual power (or filter-retained mass) found on powdered gloves.

The test method covers the determination of the amount of residual

powder and non-powder solids found on medical gloves. The mass

found for powdered gloves is assumed to be a combination of water-

insoluble residue remaining after the manufacturing process, former

release agents and donning powder.

Price RM10

MS ISO 36 : 2002

Rubber, vulcanized or thermoplastic - Determination of adhesion

to textile fabric

This Malaysian Standard specifies a method of test for measuring

the force required to separate, by stripping; two plies of fabric bonded

with rubber, or a rubber layer and a fabric ply bonded together. The

method is applicable when the ply surfaces are approximately plane

or when they are in the form of a cylinder having an internal diameter

greater than approximately 50 mm. The method is not applicable

when the ply surfaces contain sharp bends, angles or other gross

irregularities which cannot be excluded when cutting out test pieces.

Price RM10

MS ISO 296 : 2001

Natural rubber latex concentrate - Centrifuged or creamed,

ammonia-preserved types - Specification

This Malaysian Standard gives specifications for natural rubber latex

concentrate types which are preserved wholly or in part with ammonia

which have been produced by centrifuging or creaming. This standard

supersedes MS 296 : 1990.

Price RM10

MS ISO 498 : 2002

Natural rubber latex concentrate - Preparation of dry films

This Malaysian Standard specifies a method for preparing dry,

homogeneous films, substantially free of air bubbles, from natural

rubber latex concentrate. The procedure is not necessarily suitable

for latices from natural sources other than Hevea brasiliensis or for

compounded latex, vulcanized latex or artificial dispersions of rubber

or synthetic rubber latices.

Price RM10

MS ISO 6502 : 2002

Rubber - Guide to the use of curemeters

This Malaysian Standard provides guidance on the determination of

vulcanization characteristics of rubber compounds by means of

curemeters.

Price RM30

83.040.20 Rubber compounding ingredients

MS 1013 : 1986

Method of test for residual vinyl chloride monomer (Gas

Chromatographic Method).

Specifies a method for the determination of residual vinyl chloride

monomer by gas chromatography in homopolymer and copolymer

resins of vinly chloride, as well as materials and articles made from

resins.

Price RM10

83.040.30 Auxiliary materials and additives for

plastics

_____________________________________________

MS 511 : 1977

Specification for zinc oxide for use in rubber.

Covers zinc oxide intended for use as activator, pigment, accelerator

and reinforcing materials in rubber compounds. Two grades as

specified : Grade A (non-straining) and Grade B (general purpose).

Price RM60

83.060 Rubber

MS 463 : 1994

Specification for rubber (Hevea brasiliensis L.) seed for

commercial planting (First revision).

This Malaysian Standard prescribes the quality requirements for

rubber (Hevea brasiliensis) seeds for commercial plantings.

Price RM20

MS 671 : Part 1 : 2002

Specification for elastomeric bridge bearing : Part 1 : Material

testing, manufacture and installation of bearing (Second

revision)

This Malaysian Standard specifies requirements for the material,

manufacture, testing and installation of elastomeric bride bearing. It

also specifies methods of test and describes procedures for the

preparation of test pieces from finishes bearing. This standard does

not contain aspects relating to design of bearing. This standard

supersedes MS 671 : Part 1 : 1991.

Price RM20

MS 1157 : Part 16 : 1992

Methods of test for vulcanized rubber : Part 16 : Resistance to

ozone cracking - static strain test.

This Part of the standard specifies a method for the determination of

resistance of vulcanized or thermoplastic rubbers to cracking when

exposed, under static tensile strain, to air containing a definite

concentration of ozone and at a definite temperature in circumstances

that exclude the effects of direct light.

Price RM20

3

MS 1157 : Part 18 : 1992

Methods of test for vulcanized rubber : Part 18 : Determination

of modulus in shear-quadruple shear method.

This standard specifies methods for the determination of the modulus

in shear or the strength of bonds of rubber to metal or other rigid

plates, using rubber bonded between four parallel plates. Method A

describes the determination of the modulus in shear. Method B

describes the determination of the strength of the bonds.

Price RM10

MS 1157 : Part 19 : 1992


of adhesion to rigid plates in shear-quadruple shear method.

This standard specifies a method for the determination of the strength

of bonds of rubber to metal or other rigid plates where the rubber is

assembled between four parallel rigid plates. The method is applicable

primarily to test pieces prepared in the laboratory under standard

conditions such as may be used to provide date for the development

and control of rubber compounds and methods of manufacture of

bonded shear units.

Price RM10

MS 1157 : Part 22 : 1991

Methods of test for vulcanized rubber : Part 22 : Determina tion

of density.

This Malaysian Standard specifies two methods of test for the

determination of the density of solid vulcanized rubber. Such

determinations are of importance in the control of the quality of a

rubber compound and in the calculation of the mass of rubber required

to produce a given volume of vulcanized rubber.

Price RM10

MS 1157 : Part 24 : 1991

Methods of test for vulcanized rubber : Part 24 : Antistatic and

conductive products - Determination of electrical resistance.

This Malaysian Standard specifies a method of test to determine the

electrical resistance of antistatic and conductive articles and products

manufactured wholly or in part, from rubber whose electrical

resistance measured between defined points, when new does not

exceed 1 x 108 and whose conductivity is derived from the addition

of carbon black and/or other appropriate substances to the bulk of

the material.

Price RM20

MS 1157 : Part 27 : 1993


of rebound resilience.

This Malaysian Standard describes two methods for determining the

rebound resilience of rubber the hardness of which, at the test

temperature, lies between 30 IRHD and 85 IRHD. Method A uses

the Dunlop tripsometer whereas method B uses the Luke pendulum.

Results obtained using method A cannot be compared with results

obtained using method B. In cases of dispute, method B shall be the

referee test method.

Price RM30

MS 1157 : Part 29 : 1992


of static adhesion to textile cord-H-pull test.

This standard specifies a method for the determination of the static

adhesion of textile tyre cord to vulcanized rubber. It is applicable to

cords made from natural or man-made fibres. This method may be

applied, if desired, to similar cords for use in other rubber products,

but it is limited to cords of linear density not exceeding 800 mg/m

(tex).

Price RM20

MS 1157 : Part 31 : 1992


of adhesion to wire cord.

This standard specifies two methods for determining the adhesion

strength of vulcanized rubber to wire cord which is embedded in the

rubber. These methods are applicable primarily to test pieces

prepared in the laboratory under standard conditions, such as may

be used for the development and control of materials and processes

used in the manufacture of products reinforced with wire cord.

Price RM20

MS 1157 : Part 34 : 1991


of ageing characteristics by measurement of stress at a given

elongation.

This Malaysian Standard describes three methods for the purpose

of determining the ageing characteristics of the vulcanized rubber.

Price RM10

MS 1157 : Part 35 : 1991


of tension fatigue.

This Malaysian Standard describes a method for the determination

of the resistance of vulcanized rubbers to fatigue under repeated

tensile deformations, the test piece size and frequency of cycling

being such that there is little or no temperature rise. Under these

conditions, failure results from the growth of a crack that ultimately

severs the test piece.

Price RM20

MS 1157 : Part 38 : 1991


of adhesion to metal-two-plate method.

This Malaysian Standard specifies a method for determining the

adhesion strength of rubber-to-metal bands where the rubber part

is assembled between two parallel metal plates. The method is

applicable primarily to test pieces prepared in the laboratory under

standard conditions, such as may be used to provide data for the

development of rubber compounds and control of methods of

manufacture.

Price RM10

MS 1157 : Part 39 : 1991

Methods of test for vulcanized rubber : Part 39 : Preparation of

samples and test pieces for chemical test.

This Part of the standard specifies a method of preparing samples

from vulcanized rubber for use in chemical test.

Price RM10

MS 1157 : Part 40/1 : 1999

Methods of test for vulcanized rubber : Part 40/1 : Determination

of abrasion resistance using a rotating cylindrical drum device

Specifies a method for the determination of the resistance of rubber

to abrasion by means of a rotating cylindrical drum device. The

method involves determination of the volume loss of a rubber test

piece through abrasive action by rubbing over a specified grade of

abrasive cloth. This standard is technically equivalent to ISO 4649 :

1985 except for the time sequence for the mixing procedure.

Price RM20

4

MS 1157 : Part 40/2 : 1999

Methods of test for vulcanized rubber : Part 40/2 : Determination

of abrasion resistance using abrasive wheel

Specifies a method for the determination of the resistance of rubber

to abrasion by means of an abrasive wheel. This method is restricted

to rubbers with a hardness in the range of 55 IRHD to 95 IRHD.

Price RM10

MS 1157 : Part 41 : 1999


of temperature rise and resistance to fatigue in compression

flexometer testing.

Specifies the compression flexometer test for the determination of

the temperature rise and resistance to fatigue of vulcanized rubbers.

Price RM20

MS 1292 : 1992

Specification for rubber seals-water stops for sealing joints in

concrete - Specification of materials.

This Malaysian Standard specifies requirements for materials used

in vulcanized, solid rubber water stops for sealing joints in concrete

into which they are wholly or partly embedded.

Price RM10

MS 1449 : Part 1 : 1999

Rubber - Determination of metal content by atomic absorption

spectrometry : Part 1 : Determination of zinc content

Specifies an atomic absorption spectrometric method for the

determination of the zinc content of rubbers. This standard is

technically equivalent to ISO 6101-1991 except that the dissolution

after ashing is carried out using concentrated nitric acid instead of

concentrated hydrochloric acid and treatment for silicates is not

included. Price RM20

MS 1449 : Part 3 : 1999


spectrometry : Part 3 : Determination of copper content


determination of the copper content of rubbers. This standard is

technically equivalent to ISO 6101-3 : 1997 except that the dissolution

after ashing is carried out with concentrated nitric acid instead of

concentrated hydrochloric acid and treatment for silicates is not

included. It supersedes MS 281 : Part 7 : 1993.

Price RM20

MS 1449 : Part 4 : 1999


spectrometry : Part 4 : Determination of manganese content


determination of the manganese content of rubbers. This standard

is technically equivalent to ISO 6101-4 : 1997 except that the

dissolution after ashing is carried out using concentrated nitric acid

instead of concentrated hydrochloric acid and treatment for is not

included. It supersedes MS 281 Part 8 : 1993.

Price RM20

MS 1449 : Part 6 : 1999


spectrometry : Part 6 : Determination of magnesium content


determination of the magnesium content of rubbers.

Price RM20

MS 1523 : 2001

Rubber - Temperatures, humidities and times for conditioning

and testing

This Malaysian Standard specifies the temperature, humidity and

time conditions used for the conditioning and testing of all types of

rubber test piece. Special conditions applicable to a particular test

or material or simulating a particular climatic environment are not

included, nor are special requirements for testing whole products. It

also specifies the requirements for the time-interval to be observed

between forming and testing of rubber test pieces and products. Such

requirements are necessary to obtain reproducible test results and

to minimize disagreement between customer and supplier. This

standard supersedes MS 1157 : Part 13 : 1995.

Price RM10

MS 1524 : 2001

Rubber - Determination of solvent extract

This Malaysian Standard specifies two methods for the quantitative

determination of extractable material from raw rubbers, both natural

and synthetic, and their unvulcanized and vulcanized compounds.

Method B is a rapid extraction method, while method A is for use in

cases of dispute.

Price RM20

MS 1546 : 2002

Rubber - Determination of crystallization effects by hardness

measurements

This Malaysian Standard specifies a test based on hardness

measurements for determining the progressive stiffening of rubber

with time, caused by crystallization. It is limited to materials having

an initial hardness at test temperature of 10 IRHD to 85 IRHD.

Price RM20

5

MS 1548 : 2002

Rubbers, raw - Determination of volatile-matter content

This Malaysian Standard specifies two methods, a hot-mill method

and an oven method, for the determination of moisture and other

volatile-matter content in raw rubbers. This standard supersedes

MS 1359 : Part 2 : 1994.

Price RM10

MS 1568 : Part 7 : 2002

Rubber – Determination of metal content by atomic absorption

spectrometry: Part 7: Determination of calcium content

This part of Malaysian Standard specifies an atomic absorption

spectrometric method for the determination of the calcium content of

rubbers.

Price RM20

MS 1547 : 2002

Rubber latex - Determination of density between 5°C and 40°CThis Malaysian Standard specifies a method for the determination of

the density of natural rubber latex concentrate between the

temperatures of 5°C and 40°C. The standard is intended for use

when density determinations are used to calculate the mass of a

measured volume of latex in locations where it is not practical to

weigh directly or to control the temperature of the laboratory.

Price RM10

MS 1449 : Part 5 : 1999


spectrometry : Part 5 : Determination of iron content


determination of the iron content of rubbers. This standard is

technically equivalent to ISO 6101-5 : 1990 except that the dissolution

after ashing is carried out with concentrated nitric acid instead of

concentrated hydrochloric acid and the treatment for silicates is not

included. It supersedes MS 281 : Part 9 : 1993.

Price RM20

MS ISO 34-2 : 1999

Rubber, vulcanized or thermoplastic – Determination of tear

strength - Part 2 : Small (delft) test pieces

Specifies a method for the determination of the tear strength of small

test pieces (Delft test pieces) of vulcanized or thermoplastic rubber.

This standard is identical with ISO 34-2 : 1996.

Price RM20

MS ISO 37 : 1998

Rubber vulcanised or thermoplastic – Determination of tensile

stress-strain properties

This Malaysian Standard is identical with ISO 37 : 1994. This standard

describes a method for the determination of the tensile stress-strain

properties of vulcanized and thermoplastic rubbers. Properties which

may be determined are the tensile strength, the elongation at break,

the stress at a given stress means of specifying or determining the

yield point are also given. This standard shall replace MS 1157 : Part

3 : 1989, Method of test for vulcanized rubber Part 3 : Determination

of tensile stress-strain properties.

Price RM20

MS ISO 48 : 2002

Rubber, vulcanized or thermoplastic - Determination of hardness

(hardness between 10 IRHD and 100 IRHD)

This Malaysian Standard specifies four methods for the determination

of the hardness of vulcanized or thermoplastic rubbers on flat

surfaces:

Method N Normal test

Method H High-hardness test

Method L Low-hardness test

Method M Microtest

and four methods for the determination of apparent hardness of

curved surfaces using methods, N, H, L and M, respectively: Methods

CN, CH, CL and CM. This standard supersedes MS 1157 : Part A1 :

1995.

Price RM30

MS ISO 132 : 2002

Rubber, vulcanized or thermoplastic - Determination of flex

cracking and crack growth (De Mattia)

This Malaysian Standard specifies a method of test intended for use

in comparing the resistance of rubbers to the formation and growth

of cracks, when subjected to repeated flexing on the De Mattia type

machine. For determination of crack growth, an artificial cut is made

in the test piece to initiate cut growth. This standard supersedes MS

1157 : Part 10 : 1993.

Price RM20

MS ISO 188 : 2001

Rubber, vulcanized or thermoplastic - Accelerated ageing and

heat resistance tests

This Malaysian Standard specifies accelerated ageing or heat

resistance tests on vulcanized or thermoplastic rubbers. The methods

are: Method A: air-oven method using a cell-type oven or cabinet

oven with low air speed and a ventilation of 3 to 10 changes per

hour; Method B: air-oven method using a cabinet oven with forced

air circulation by means of a fan and a ventilation of 3 to 10 changes

per hour; and Method C: oxygen pressure method at 2, 1 Mpa and

70°C. This standard supersedes MS 1157 : Part 4 : 1989.

Price RM20

MS ISO 247 : 2001

Rubber : Determination of ash

This Malaysian Standard specifies two methods for the determination

of ash from raw rubbers, compounded rubbers and vulcanizates.

The methods are applicable to raw, compounded or vulcanized

rubbers of the M,N,O,R and U families. This standard supersedes

MS 1359 : Part 1 : 1994.

Price RM10

6

MS ISO 287 : 1999

Paper and board – Determination of moisture content – oven –

drying method

Specifies an oven-drying method for the determination of the moisture

content of paper and board at the time of sampling. The method is

applicable to all paper and board, including corrugated fibreboard

and solid fibreboard, provided that the paper or board does not contain

any substance, other than water, that will escape at the temperature

specified for the test. This standard is identical with ISO 287 - 1985

and it supersedes MS 126 : 1973.

Price RM10

MS ISO 289-1 : 1998

Rubber, unvulcanized –Determinations using a shearing – disc

viscometer – Part 1 : Determination of Mooney viscosity.

This Malaysian Standards specifies a method of use of a shearing

disc viscometer for measuring the Mooney viscosity of

uncompounded or compounded rubbers.

Price RM20

MS ISO 289-2 : 1998

Rubber, unvulcanized –Determinations using a shearing – disc

viscometer – Part 2: Determination of pre-vulcanization

characteristics.

This Malaysian Standards specifies a method for determination the

pre-vulcanization characteristics of compounded rubber. The pre-

vulcanisation characteristics determined by this method provide a

means of estimating how long compounded rubber can be maintained

at high temperatures and remain processable.

Price RM10

MS ISO 780 : 2001

Packaging - Pictorial marking for handling goods

This Malaysian Standard specifies a set of symbols conventionally

used for marking of transport packages in their physical distribution

chain to convey handling instructions. The symbols should be used

only when necessary. This Malaysian Standard is applicable to

packages containing any kind of goods, but does not include

instructions specific to the handling of dangerous goods. This standard

supersedes MS 984 : 1985

Price RM20

MS ISO 813 : 1999

Rubber, vulcanized or thermoplastic – Determination of adhesion

to a rigid substrate – 90 ° peel method

Specifies a method for the determination of the adhesive strength of

a vulcanized or thermoplastic rubber bonded to a rigid substrate,

using a test piece comprising a strip of rubber bonded to a single

plate of rigid material. The method is applicable primarily to test pieces

prepared in the laboratory under standard conditions, such as may

be used to provide data for the choice of rubber compounds or

adhesive systems, the development of such materials and the control

of manufacturing processes. This method is not suitable for high-

hardness rubbers. This standard identical with ISO 813 : 1997 and it


Price RM20

MS ISO 815 : 1998

Rubber, vulcanised or thermoplastic-Determination of

compression set at ambient, elevated or low temperatures

This Malaysian Standard specifies methods for determination of

compression set characteristics of vulcanised and thermoplastic

rubber at ambient , elevated or low temperatures. The methods are

intended to measured the ability of rubber of hardness within the

range 10 IRHD to 95 IRHD to retain their elastic properties at specified

temperature after prolonged compression at constant strain (where

possible 25%) under one of the alternative sets of condition described.

For rubber of hardness greater than 80 IRHD, a lower compression

strain is used: 15% for a normal hardness from 80 IRHD to 89 IRHD

and 10% for a nominal hardness from 90 IRHD to 95 IRHD.

Price RM20

MS ISO 1431-2 : 1999

Rubber, vulcanized or thermoplastic – Resistance to ozone

cracking - Part 2 : Dynamic strain test

Specifies a method intended for use in estimating the resistance of

vulcanized or thermoplastic rubbers to cracking when exposed, under

dynamic tensile strain, to air containing a definite concentration of

ozone and at a definite temperature in circumstances that exclude

the effects of direct light. This standard is identical with ISO 1431-2 :

1994.

Price RM20

MS ISO 1432 : 2000

Rubber, vulcanized or thermoplastic – Determination of low

temperature stiffening (Gehman test)

Specifies a static procedure, known as the Gehman test, for

determining the relative stiffness characteristics of vulcanized or

thermoplastic rubbers over a temperature to approximately –

150°C. This standard is identical with ISO 1432 : 1988.

Price RM10

MS ISO 1433 : 2000

Rubber, vulcanized - Preferred gradations of properties

Lays down preferred numerical values for the gradation of various

physical properties of solid vulcanized rubber determined in

accordance with standard methods of test. The standard is identical

with ISO 1433: 1995.

Price RM20

MS ISO 1817 : 2002

Rubber, vulcanized - Determination of the effect of liquids

This Malaysian Standard describes methods of evaluating the

resistance of vulcanized thermoset or thermoplastic rubbers to the

action of liquids by measurement of properties of the rubbers before

and after immersion in test liquids. The liquids concerned include

current service liquids, such as petroleum derivatives, organic

solvents and chemical reagents as well as reference test liquids.

This standard supersedes MS 1157 : Part 20 : 1991.

Price RM30

MS ISO 1853 : 2002

Conducting and dissipative rubbers, vulcanized or thermoplastic

- Measurement of resistivity

This Malaysian Standard specifies the requirements for the laboratory

testing of the volume resistivity of specially prepared test pieces of

vulcanized or thermoplastic rubber compounds rendered conducting

or dissipative by the inclusion of carbon black or ionizable materials.

Antistatic properties may also be conferred on rubber materials by

the incorporation of ionizable materials into the rubber mix. The test

is suitable for materials with a resistivity of less than 1010 Wm.

Price RM20

MS ISO 2285 : 1999

Rubber, vulcanized or thermoplastic – Determination of tension

set at normal and high temperatures

Specifies a method for determining the tension set characteristics of

vulcanized or thermoplastic rubbers. The test is intended to measure

the ability of rubbers of hardness within the range 30 to 94

International Rubber Hardness Degrees (IRHD) to retain their elastic

properties after extension, at a standard temperature to a specified

strain which is maintained for a specified time at the same or at a

specified higher temperature and then released at the standard

temperature. This standard is identical with ISO 2285 : 1988 and it


Price RM10

MS ISO 2393 : 2000

Rubber test mixes - Preparation, mixing and vulcanization -

Equipment and procedures

Specifies the equipment and procedures for the preparation, mixing

and vulcanization of test mixes, as specified in the rubber evaluation

procedures. This standard is identical with ISO 2393 : 1994.

Price RM20

MS ISO 2782 : 1999

Rubber, vulcanized or thermoplastic - Determination of

permeability to gases.

Describes two procedures for measuring the permeability of rubber

to gases under steady-state conditions. One uses a horizontal

measuring device for measurements at constant pressure and the

other uses a vertical measuring device for measurements at constant

volume or constant pressure. The results obtained by these

procedures may be extrapolated to thicknesses of material different

from that of the test piece providing the rubber is homogeneous and

isotropic. This standard is identical with ISO 2782 : 1995 and it

supersedes MS 1157 : Part 15: 1993.

Price RM20

MS ISO 2921 : 2001

Rubber, vulcanized - Determination of low-temperature

characteristics - Temperature-retraction procedure (TR test)


the temperature-retraction characteristics of extended vulcanized

rubber.

Price RM10

MS ISO 3383 : 1998

Rubber-General directions for achieving elevated or subnormal

temperatures for test purposes.

Malaysian Standard specifies general requirements for achieving

elevated or subnormal temperatures in the testing of rubber and other

elastometric materials. It specifies general principles of the

construction and operating of temperature controlled chambers for

conditioning and/or testing . For some tests-for example ageing tests-

special procedures, conditions or equipment which differ from those

specified in this Malaysian Standard may be required . In such cases,

the requirements should be included in the method of test and

supersede the requirements of this Malaysian Standard.

Price RM10

MS ISO 3384 : 2002

Rubber, vulcanized or thermoplastic - Determination of stress

relaxation in compression at ambient and at elevated

temperatures

This Malaysian Standard specifies two methods for determining the

decrease in counter force exerted by a test piece of vulcanized or

thermoplastic rubber which has been compressed to a constant

deformation and maintained thus at a predetermined test temperature.

Two forms of test piece are permitted: cylindrical test pieces and

rings. Different shapes and sizes of test piece give different results,

and comparison of results should be limited to test pieces of similar

size and shape. This standard supersedes MS 1157 : Part 32 : 1991.

Price RM20

MS ISO 3865 : 1999

Rubber, vulcanized or thermoplastic – Methods of test for

staining in contact with organic material

Specifies three methods for estimating the staining of organic finishes

9in the following called ‘organic material’) by vulcanized or

thermoplastic rubber:- method A: contact and migration stain;-

method B: extraction stain;- method C: penetration stain; as defined

in clause 3. This standard is identical with ISO 3865 : 1997.

Price RM20

MS ISO 4648 : 1998

Rubber, vulcanised or thermoplastic – determination of

dimensions of test pieces and product for test purposes.

Malaysian Standard specifies 4 methods for the measurement of the

dimensions of solid vulcanised or thermoplastic rubber test pieces

or products for test purposes, three contact methods, designated

A,B and C and one non-contact method designated D. The method

to be used is selected according to the magnitude of the dimension

to be measured and to be desired accuracy.

7

Method A – for dimension less than 30mm

Method B - for dimension less than 30mm and up to and including

100mm

Method C – for dimension over 100 mm

Method D – non-contact procedure for all dimensions

Price RM10

MS ISO 4661-1 : 1998

Rubber, vulcanised or thermoplastic – Preparation of samples

of samples and test pieces- Part 1 : Physical tests.

This Malaysian Standard specifies methods of preparing test pieces

from vulcanised and thermoplastic rubber for use in physical tests

on rubber specified in other Malaysia Standards.

Price RM10

MS ISO 4665 : 2002

Rubber, vulcanized and thermoplastic - Resistance to weathering

This Malaysian Standard specifies methods for the exposure of rubber

materials to natural or artificial weathering and methods for the

determination of changes in colour, appearance and physical

properties resulting from exposure.

Price RM20

MS ISO 6471 : 2000

Rubber, vulcanized – Determination of crystallization effects

under compression

Specifies a method for the determination of the tendency of vulcanized

rubbers to crystallization, by measurement of the recovery of

compressed test pieces. This standard is identical with ISO 6471 :

1994.

Price RM20

MS ISO 7619 : 2000

Rubber – Determination of indentation hardness by means of

pocket hardness meters

Specifies a method for the determination of the indentation hardness

of rubber by means of pocket hardness meters

of two types: a) the Shore-type durometer; b) a meter calibrated in

IRHD. This standard is identical with ISO 7619 : 1997 and it


Price RM20

MS ISO 8013 : 2005

Rubber, vulcanized – Determination of creep in compression or

shear

This standard specifies a method for the determination of creep in

rubber continuously subject to compressive or to shear forces. The

standard cannot be used for intermittent deformation of rubber.

Price RM140

MS ISO 8789 : 2005

Rubber hoses and hose assemblies for liquefied petroleum gas

in motor vehicle – Specification

This Malaysian Standard specifies the requirements for rubber hoses

and hose assemblies, up to a maximum bore of 20 mm, for use in

motor vehicles with liquefied petroleum gas (LPG) installations. The

hoses are designed for use up to a maximum pressure 2,5 MPa (25

bar) and a working temperature between - 40oC and + 80

oC.

Price RM90

MS ISO 9026 : 1998

Raw rubber or unvulcanized compounds – Determination of

green strength

This Malaysian Standards specifies a method for the determination

of green strength of raw rubber or unvulcanized–rubber compounds

using a tensile stress –strain test, the test pieces being prepared

following standard test condition, or cut from calendered sheets.

Price RM20

8

MS ISO 11346 : 1999

Rubber, vulcanized or thermoplastic – Estimation of life-time

and maximum temperature of use from an arrhenius plot

Describes the principles and procedures for estimating the life-time

and maximum temperature of use of vulcanized or thermoplastic

rubbers, using an Arrhenius plot. This method is suitable for different

tests on rubber, but for tests under stress or deformation (creep,

relaxation, etc.) physical (viscoelastic) changes of material cannot

easily be separated from any chemical change. Then the Arrhenius

equation is no longer the only possible model, and the Willams,

Landel, Ferry (WLF) equation may be more suitable to represent the

change in the material as a function of time. This standard is identical

with ISO 11346 : 1997.

Price RM10

83.080 Plastics

MS 1440 : 1998

Glossary of terms for plastics

This Malaysian Standard defines terms used in plastic industry. The

terms are listed alphabetically.

Price RM150

MS 1501 : 2000

Method of test for measuring shrinkage from mould dimensions

of moulded plastics

Intended to measure batch to batch uniformity in initial shrinkage

from mould to moulded dimensions of eiher thermoplastic or

thermosetting materials when moulded by compression, injection or

transfer under specified conditions. This test method does not provide

for the measurement of shrinkages that may occur as moulded

materials age, after the first 48 hours out of the mould.

Price RM30

MS ISO 489 : 1998

Plastics – Determination of the refractive index of transparent

plastics

This standard specifies two methods of test for determining the

refractive index of transparent plastics, namely

Method A : Refractometric method for measuring the refractive index

of transparent cast, moulded or sheet materials by means of a

refractometer,

Method B : Immersion method for determining the refractive index

of powdered or granulated transparent materials by means of a

microscope and making use of the Becke line phenomenon.

Price RM10

MS ISO 844 : 1998

Cellular plastics – Compression test for rigid materials

This standard specifies a method of test for determining the

compressive strength and corresponding relative deformation or the

compressive stress at 10 % relative deformation of rigid cellular

plastics.

Price RM20

MS ISO 877 : 2001

Plastics - Methods of exposure to direct weathering, to

weathering using glass-filtered daylight, and to intensified

weathering by daylight using Fresnel mirrors

This Malaysian Standard specifies methods of exposing plastics to

solar radiation, either by direct exposure to natural weathering

(Method A), to indirect solar radiation by modification of its spectral

distribution with glass to simulate ageing of plastics behind building

or automotive window glass (Method B), or to solar radiation intensi-

fied by the use of Fresnel mirrors to achieve acceleration of the

weathering processes (Method C). The purpose is to assess changes

produced after specified stages of such exposures.

Price RM30

83.080.01 Plastics in general

MS 1271 : 1992

Method of test for plastics : Determination of hardness : Shore

hardness.


the indentation hardness of plastics by means of durometers of two

types durometer type A is used for softer materials and durometer

type D used for harder materials (see the note in clause 7.2 of the

standard). The method permits measurement either of the initial

indentation or of the indentation after a specified period of time, or

both.

Price RM10

MS 1272 : Part 1 : 1993

Method of test for plastics : Determination of hardness : Part 1

: Ball indentation method.

This Part of the standard specifies a method for determining the

hardness of plastics and ebonite by means of a loaded ball indenter.

The ball indentation hardness determined by this method may provide

data for research and development, quality control and acceptance

or rejection under specifications.

Price RM10

MS 1272 : Part 2 : 1992

Method of test for plastics : Determination of hardness : Part 1

: Rockwell hardness.

This Part of standard specifies a method for determining the

indentation hardness of plastics by means of the Rockwell hardness

tester using the Rockwell M, L and R hardness scales.

Price RM20

MS 1274 : 1992

Method of test for plastics : Determination of temperature of

deflection under load.

This standard specifies two methods for the determination of

temperature of deflection under load (bending stress) of plastics:

- Method A using a nominal surface stress of 1.80 MPa;

- Method B using a nominal surface stress of 0.45 MPa.

Price RM20

MS 1345 : 1993

Method of test for plastics – Determination of tensile creep.

This standard specifies a method for the determination of tensile

creep of rigid plastic materials in the form of test specimens such as

those employed for the determination of tensile properties, moulded

directly or cut from sheets.

Price RM20

MS 1349 : 1994

Method of test for plastics – Determination of flexural properties

of rigid plastics.


flexural properties of rigid non-reinforced and fibre-reinforced plastic

materials, in the form of rectangular bars of standard on non-standard

dimensions, moulded directly or cut from sheets or other shapes. It

applies only to a simple, freely supported beam, loaded at mid-span.

Price RM20

MS 1371 : 1995

Methods of test for environmental stress - cracking of ethylene

plastics.

This Malaysian Standard specifies methods for the determination of

the susceptibility of ethylene plastics to environmental stress -

cracking when subjected to certain condition. Under certain conditions

of stress and in the presence of environments such as soaps, wetting

agents, oils or detergent, ethylene plastics may exhibit mechanical

failure by cracking.

Price RM20

MS 1406 : 1996

Code of practice for system of tolerances for the dimension of

plastics moulding.

This code of practice recommends a system of tolerances for

dimensions of plastics mouldings produced from thermoplastics and

thermosetting moulding materials by compression moulding, transfer

moulding or injection moulding.

Price RM20

MS 1421 : 2005

Test method for haze and luminous transmittance of transparent

plastics (First revision)

This Malaysian Standard covers the evaluation of specific light-

transmitting and wide-angle-light-scattering properties of planner

sections of materials such as essentially transparent plastic. Two

procedures are provided for the measurement of luminous

transmittance and haze.

Price RM40

MS 1441 : 1998

Method of test for seal strength of flexible barrier materials.

This test method covers the measurement of the seal strength of

flexible barrier materials.

Price RM10

MS 1442 : 1998

Methods of test for the assessment of carbon black dispersion

in polyethylene using a microscope.

These methods describe procedures for assessing the uniformity of

the dispersion of carbon black in a compound, Extrusion or moulded

article.

Price RM10

MS 1465 : Part 1 : 1999

Method of test for determination of plastics resistivity : Part 1 :

Surface resistivity

Specifies a method for determining the electrical surface resistivity

of plastics from the current flowing between two electrodes mounted

on the surface of the material when a voltage is applied between

them. Procedures with various types of apparatus are described. All

procedures enable the operator to determine surface resistivity when

residual charge is negligible. One procedure, using a circuit shown

in Figure 5, facilitates the determination of significant residual charge.

The method is suitable for materials with a range of surface resistivity

levels of 108 W or greater. The range of applicability may be extended

by the used of appropriate electrode systems and measuring devices.

Price RM20

9

MS 1465 : Part 2 : 1999

Method of test for determination of plastics resistivity : Part 2 :

Volume resistivity

Specifies a method for determining the electrical volume resistivity

of plastics from the current flowing through the material when a voltage

is applied to the opposite faces of a sheet of the material. The method

is unsuitable when the volume resistivity is below 107 W cm. Lower

values should be measured by the method given in BS 2044.

Price RM20

MS 1466 : 1999

Method of test for linear thermal expansion of solid materials

by thermomechanical analysis

Specifies a method for the determination of linear thermal expansion

of solid materials using thermomechanical analysis techniques. This

test method is applicable to solid materials that exhibit sufficient rigidity

over the test temperature range such that the sensing probe does

not produce indentation of the specimen and is applicable to the

temperature range from – 120°C to 600°C. The temperature

range may extended depending upon the instrumentation and

calibration materials used.

Price RM20

MS 1467 : 1999

Method of test for determination of 2 % secant modulus for

polyethylene films

Specifies a method for calculating the 2 % secant modulus for

polyethylene film less than 1.0 mm in thickness. This standard will

facilitate modulus comparisons of similar materials by standardising

the method for deriving the points on the stress-strain curve from

which the calculations are performed.

Price RM10

MS 1468 : 1999

Method of test for determining the 24-hour gas (air) space

acetaldehyde content of freshly blown polyethylene

terephthalate (pet) bottles

Specifies a method for determining the 24 h gas-space acetaldehyde

(AA) content of freshly blown polyethylene terephthalate (PET)

bottles. The test method, containing internal or external standard

calibration, is applicable to all PET bottles.

Price RM20

MS 1469 : 1999

Specification for plastic lenses for automotive lamps

Prescribes the specifications for the plastic lenses for automotive

lamps. It does not specify the complete lamps.

Price RM10

MS 1470 : 1999

Specification for PVC floor mats for motor vehicles

Prescribes the specifications for floor mats made of PVC intended

for use in motor vehicles.

Price RM10

MS 1473 : 1999

Method of test for measuring the dynamic mechanical properties

of plastics using three point bending

Specifies the use of dynamic mechanical instrumentation for gathering

and reporting the viscoelastic properties of thermoplastic and

thermosetting resins and composite systems in the form of rectangular

bars moulded directly or cut from sheets, plates, or moulded shapes.

The data generated, using three-point bending techniques, may be

used to identify the thermomechanical properties of plastics material

or composition using a variety of dynamic mechanical instruments.

The standard is valid for a wide range of frequencies, typically from

0.01 Hz to 100 Hz.

Price RM10

10

MS 1476 : 1999

Method of test for determining the carbon dioxide loss of plastics

beverage containers

Specifies a method for determining the carbon dioxide (CO2) loss

from plastics beverage containers after a specified period of storage

time. Factors contributing to this pressure loss are volume expansion

and the gas transport characteristics of the package including

permeation and leakage.

Price RM20

MS 1808 : 2005

Test method for indentation hardness of rigid plastics by means

of a Barcol Impressor

This Malaysian Standard covers the determination of indentation

hardness of both reinforced and non-reinforced rigid plastics using a

Barcol Impressor, Model No. 934-1 and Model No. 935.

Price RM40

MS ISO 60 : 2004

Plastics – Determination of apparent density of material that

can be poured from a specified funnel

This standard specifies a method of determining the apparent density,

i.e. the mass per unit of volume of loose material (powdered or

granular material) that can be poured from a funnel of specified

design. Price RM10

MS ISO 62 : 2001

Plastics - Determination of water absorption

This Standard describes procedures for determining the amount of

water absorbed by plastic specimens of defined dimensions, when

immersed in water or when subjected to humid air under controlled

conditions. The “through-the-thickness” moisture diffusion coefficient

can be determined for single-phase material by assuming Fickian

diffusion behaviour with constant moisture absorption properties

through the thickness of the test specimen.

Price RM20

MS ISO 75-1 : 1999

Plastics – Determination of temperature of deflection under load

- Part 1 : General test method

Specifies methods for the determination of the temperature of

deflection under load (bending stress under three-point loading) of

different types of material. The methods specified are suitable for

assessing the behaviour of the different types of material at elevated

temperature under load at a specified rate of temperature increase.


Price RM10

MS ISO 75-2 : 1999


- Part 2 : Plastics and ebonite

Specifies three methods for the determination of the temperature of

deflection under load (bending stress) of plastics and ebonite:

- method A, using a nominal surface stress of 1.80 MPa;

- method B, using a nominal surface stress of 0.45 MPa;

- method C, using a nominal surface stress of 8.00 MPa.


Price RM10

MS ISO 75-3 : 1999


- Part 3 : High-strength thermosetting laminates and long-fibre-

reinforced plastics

Specifies a method for the determination of the temperature of

deflection under load (bending stress) of high-strength thermosetting

laminates and compression-moulded long-fibre-reinforced plastics.

The test load used is not a fixed load, as in part 2 of this International

Standard, but a function (1/10) of the ultimate or specified load. This

allows the method to be applied to materials with a wide range of

strengths and bending moduli. This standard is identical with ISO

75-3 : 1993.

Price RM10

MS ISO 291 : 2000

Plastics - Standard atmospheres for conditioning and testing

Sets out specifications relating to the conditioning and testing of all

plastics and all types of test specimens at constant atmospheric

conditions which correspond to the average atmospheric conditions

in laboratories. This standard supersedes MS 1346 : 1993.

Price RM20

MS ISO 305 : 2001

Plastics - Determination of thermal stability of poly (vinyl

chloride), related chlorine-containing homopolymers and

copolymers and their compounds - Discoloration method


of the thermal stability of products and compounds based on vinyl

chloride homopolymers and copolymers (referred to simply as PVC

in the following text) by the extent of the discoloration that occurs

when they are exposed, in the form of sheet, to elevated temperatures.

- Method A : Oil-bath method

- Method B : Oven

Price RM10

MS ISO 489 : 1998

Plastics – Determination of the refractive index of transparent

plastics

This standard specifies two methods of test for determining the

refractive index of transparent plastics, namely

Method A : Refractometric method for measuring the refractive index

of transparent cast, moulded or sheet materials by means of a

refractometer, Method B : Immersion method for determining the

refractive index of powdered or granulated transparent materials by

means of a microscope and making use of the Becke line

phenomenon.

Price RM10

MS ISO 527 : Part 1 : 1994

Plastics – Determination of tensile properties: Part 1: General

principles.

This Malaysian Standard specifies the test general principles for

determining the tensile properties of plastics and plastic composites

under defined conditions. Several different types of test specimen

are defined to suit different types of material which are detailed in

subsequent parts of this Malaysian Standard.

Price RM20

MS ISO 527 : Part 2 : 1994

Plastics – Determination of tensile properties: Part 2 : Test

conditions for moulding and extrusion plastics.

This Malaysian Standard specifies the test conditions for determining

the tensile properties of moulding and extrusion plastics, based upon

the general principles.

Price RM10

MS ISO 604 : 2003

Plastics – Determination of compressive properties


compressive properties of plastics under defined conditions. A

standard test specimen is defined but its length may be adjusted to

prevent buckling under load from affecting the results. A range of

test speeds is included. The method applies to the following range of

materials:

- rigid and semi-rigid [1] thermoplastic moulding and extrusion

materials, including compounds filled and reinforced by e.g.

short fibres, small rods, plates or granules in addition to

unfilled types; rigid and semi-rigid thermoplastic sheet;

- rigid and semi-rigid thermoses moulding materials, including

filled and reinforced compounds; rigid and semi-rigid

thermoses sheet;

- thermotropic liquid-crystal polymers.

Price RM30

MS ISO 175 : 2001

Plastics - Methods of test for the determination of the effects of

immersion in liquid chemicals

This Malaysian Standard specifies a method of exposing test

specimens of plastic materials, free from all external restraint, to liquid

chemicals, and methods for determining the changes in properties

resulting from such immersion. This standard supersedes MS 1341

: 1993.

Price RM30

MS ISO 176 : 2001

Plastics - Determination of loss of plasticizers - Activated carbon

method.

This Malaysian Standard specifies two empirical methods for the

quantitative determination of the loss of mass from a plastic material

under defined conditions of time and temperature, in the presence of

activated carbon.

Price RM10

MS ISO 177 : 2001

Plastics - Determination of migration of plasticizers


the tendency of plasticizers to migrate from plastics in which they

are contained into other materials or other plastics when they are

brought into close contact.

Price RM10

MS ISO 178 : 2004

Plastics – Determination of flexural properties

This Malaysian standard specifies a method for determining the

flexural properties of rigid and semi-rigid plastics under defined

conditions. A standard test specimen is defined, but parameters are

included for alternative specimen sizes for use where appropriate. A

range of test speeds in included.

Price RM30

MS ISO 179-1 : 2002

Plastics - Determination of Charpy impact properties - Part 1 :

Non-instrumented impact test


Charpy impact strength of plastics under defined conditions. A

number of different types of specimen and test configurations are

defined. Different test parameters are specified according to the

type of material, the type of test specimen and the type of notch.

Price RM30

MS ISO 179-2 : 2002

Plastics - Determination of Charpy impact properties - Part 2 :

Instrumented impact test

This Malaysian Standard specifies a method for determining Charpy

impact properties of plastics from force-deflection diagrams. Different

types of rod-shaped test specimen and test configuration, as well as

test parameters depending on the type of material, the type of test

specimen and the type of notch are defined in part 1 of ISO 179.

Dynamic effects such as load-cell/striker resonance, test specimen

resonance and initial-contact/inertia peaks are described (see Figure

1, curve b, and Annex A).

Price RM30

MS ISO 180 : 2002

Plastics - Determination of Izod impact

This Malaysian Standard specifies a method for determining the Izod

impact strength of plastics under defined conditions. A number of

different types of specimen and test configurations are defined.

Different test parameters are specified according to the type of

material, the type of test specimen and the type of notch. The method

is used to investigate the behaviour of specified types of specimen

under the impact conditions defined and for estimating the brittleness

or toughness of specimens within the limitations inherent in the test

conditions. This standard supersedes MS 1270 : 1992.

Price RM20

11

MS ISO 844 : 1998

Cellular plastics – Compression test for rigid materials

This standard specifies a method of test for determining the

compressive strength and corresponding relative deformation or the

compressive stress at 10 % relative deformation of rigid cellular

plastics.

Price RM20

MS ISO 868 : 2004

Plastics and ebonite – Determination of indentation hardness

by means of a durometer (Shore hardness)

This standard specifies a method for the determination of the indention

hardness of plastics and ebonite by means of durometers of two

types: type A is used for softer materials and type D for harder

materials. The method permits measurement either of the initial

indentation or of the identation after a specified period of time, or

both.

Price RM20

MS ISO 899-1 : 1999

Plastics – Determination of creep behaviour - Part 1 : Tensile

creep

Specifies a method for determining the tensile creep of plastics in

the form of standard test specimens under specified conditions such

as those of pretreatment, and humidity. This standard is identical

with ISO 899-1 : 1993.

Price RM20

MS ISO 899-2 : 1999

Plastics – Determination of creep behaviour - Part 2 : Flexural

creep by three-point loading

Specifies a method for determining the flexural creep of plastics in

the form of standard test specimens under specified conditions such

as those of pretreatment, temperature and humidity. It applies only

to a simple freely supported beam loaded at mid-span (three-point-

loading test). This standard is identical with ISO 899-2 : 1993.

Price RM20

MS ISO 974 : 2003

Plastics – Determination of the brittleness temperature by impact

This Malaysian Standard is identical with ISO 974:2000. This

Malaysian Standard specifies a method for the determination of the

temperature at which plastics that are not rigid at normal ambient

temperature exhibit brittle failure under specified impact conditions.

The method utilises a statistical technique to quantify the brittleness

failure temperature. It establishes the temperature at which there is

a 50 % chance of failure in either unnotched or notched specimens.

Price RM20

MS ISO 1043-1 : 2004

Plastics – Symbols and abbreviated terms : Part 1 : Basic

polymers and their special characteristics (First revision)

This Malaysian Standard gives uniform abbreviated terms for plastics

and symbols for components of these terms. It includes only those

abbreviated terms that have come into established use, and its aim

is both to prevent the occurrence of more than one symbol for a

given plastics term, and to prevent the interpretation of more than

one meaning for a given symbol.

Price RM20

MS ISO 1043-2: 2004

Plastics - Symbols and abbreviated terms: Part 2 : Fillers and

reinforcing materials (First revision)

This Malaysian Standard provides uniform symbols for terms referring

to fillers and reinforcing materials. It includes only those symbols

that have come into established use, and its aim is both to prevent

the occurrence of more than one symbol for a given filler or reinforcing

materials, and to prevent the interpretation of a given symbol in more

than one way.

Price RM10

12

MS ISO 1043-3 : 2004

Plastics – Symbols and abbreviated terms : Part 3 : Plasticizers

(First revision)

This Malaysian Standard gives uniform symbols for components of

terms relating to plasticizers to form abbreviated terms. It includes,

in general, only those abbreviated terms that have come into

established use. The purpose of this Malaysian Standard is to prevent

the occurrence of more than symbol for a given plasticizers.

Price RM20

MS ISO 1043-4 : 2004

Plastics – Symbols and abbreviated terms – Part 4 : Flame

retardants

This Malaysian Standard provides uniforms symbols for flame

retardants added to plastics materials. The symbols are written with

the abbreviated term ”FR” and one or more succeeding code numbers

are given in clause 5.

Price RM10

MS ISO 1183 : 1995

Plastics - Methods for determining the density and relative

density of non-cellular plastics.

This standard specifies four methods for the determination of the

density and relative density of non-cellular plastics in the from of

sheet, film, tube, moulded objects, and moulding powders, granules

and pellets. The methods including immersion, pyknometer, titration

and density gradient column method.

Price RM20

MS ISO 1210 : 1995

Plastics - Determination of the burning behaviour of horizontal

and vertical specimens in contact with a small flame ignition

source.

This standard specifies a small scale laboratory screening procedure

for comparing the relative burning behaviour of vertically or

horizontally oriented platic specimens exposed to a small-flame

ignition source. This method of test determines the afterflame/

afterglow times and damaged length of specimens.

Price RM20

MS ISO/R 1326 : 1995

Plastics - Determination of flammability and burning rate of

plastics in the form of film.

This standard describes a method for determining the relative

flammability and the burning rate of plastics in the form of sheets or

films of thickness between 1.5 mm and 0.05 mm. This method

provides a means of comparing the flammability of plastics in sheet

or film form.

Price RM10

MS ISO 1628-1 : 2004

Plastics – Determination of the viscosity of polymers in dilute

solution using capillary viscosmeters – Part 1: General principles

This standard defines the general conditions for the determination of

the reduced viscosity, intrinsic viscosity and K-Value of organic

polymers in dilute solution. It defines the standard parameters that

are applied to viscosity measurement, and can be used to develop

standards for measuring the viscosities in solution of individual types

of polymer. It can also be used to measure and report the viscosities

of polymers in solution for which no separate standards exist.

Price RM30

MS ISO 1628-2 : 2004

Plastics – Determination of the viscosity of polymers in dilute

solution using capillary viscosmeters – Part 2: Poly(vinyl

chloride) resins

This standard specifies conditions for the determination of the reduced

viscosity (also known as viscosity number) and K-value of PVC resins.

It is applicable to resins in powder form which consist

MS ISO 3167 : 2003

Plastics – Multipurpose test specimens

This Malaysian Standard specifies requirements relating to

multipurpose test specimens for plastic moulding materials intended

for processing by injection or direct compression moulding.

Specimens of types A and B are tensile test specimens from which,

with simple machining, specimens for a variety of other tests can be

taken (see Annex A). Because they have such wide utility, these

tensile specimens are referred to in this International Standard as

multipurpose test specimens. This standard supersedes MS ISO

3167: 2000.

Price RM20

MS ISO 4582 : 2001

Plastics - Determination of changes in colour and variations in

properties after exposure to daylight under glass, natural

weathering or laboratory light sources (First revision)

Describes procedures used to determine changes in colour and other

appearance properties, and variations in mechanical or other

properties, of plastics that have been exposed to daylight behind

glass, natural weathering or light from a laboratory source. The

procedure used to analyse data depends on whether the test used

to characterize the materials being exposed is destructive or non-

destructive. The exposures are conducted under conditions described

in specific exposure standards. This standard supersedes MS ISO

4582 : 1995

Price RM30

MS ISO 4589-1 : 2000

Plastics – Determination of burning behaviour by oxygen index

– Part 1 : Guidance

Constitutes s guidance document for the OI test. It provides

information to guide the reader in the use of the test procedures

described in parts 2 and 3. This standard is identical with ISO 4589-

1 : 1996. Price RM20

MS ISO 4607 : 1995

Plastics – Method of exposure to natural weathering.

This standard describes procedures for exposing plastics to natural

weathering in order to assess changes produced after specified

stages of such exposure.

Price RM20

MS ISO 4892-1 : 1998

Plastics - Methods of exposure to laboratory light sources : Part

1 : General Guidance.

This Malaysian Standard provides information and general guidance

relevant to the selection and operation of the methods of exposure

described in detail in subsequent parts.

Price RM20

MS ISO 4892-2 : 1998

Plastics-Methods of exposure to laboratory light sources –Part

2 : Xenon-arc sources.

This Malaysian Standard specifies method for exposing specimens

to xenon-arc light sources.

Price RM20

MS ISO 4892-3 : 1998


3 : Fluorescent UV lamps.


to different types of fluorescent UV lamp.

Price RM20

MS ISO 4892-4 : 1998


4 : Open flame carbon-arc lamps.


to open flame carbon-arc lamps.

Price RM20

of homo-polymers of the monomer vinyl chloride and copolymers,

terpolymers, etc., of vinyl chloride with one or more other monomers,

but where vinyl chloride is the main constituent. The resins may

contain small amount of unpolymerised substances (e.g. emulsifying

or suspending agents, catalyst residues, etc.) and other substances

added during the course of the polymerisation

Price RM20

MS ISO 1675 : 1995

Plastics - Liquid resins - Determination for density and relative

density by pyknometer method.

This standard specifies a method for the determination of the density

of liquid resins using a pyknometer of known volume.

Price RM10

MS ISO 1798 : 1998

Flexible cellular polymeric materials-Determination of tensile

strength and elongation break.


strength and deformation properties of flexible cellular materials when

a test piece is extended at a constant rate until it breaks.

Price RM10

MS ISO 2039-1 : 2004

Plastics – Determination of hardness – Part 1: Ball indention

method

This standard specifies a method for the determining the hardness

of plastics and ebonite by means of a loaded ball indenter.

Price RM20

MS ISO 2555 : 1995

Plastics - Resins in the liquid state or as emulsions or

dispersions - Determination of apparent viscosity by the

Brookfield test method.

This standard specifies a method of determining an apparent viscosity,

by the Brookfield test method, of resins in a liquid or similar state,

using one of the types of rotational viscometer described in this

standard.

Price RM20

MS ISO 2578 : 1995

Plastics - Determination of time temperature limits after

prolonged exposure to heat.

This standard specifies the principles and procedures for evaluating

the thermal endurance properties of plastics exposed to elevated

temperature for long periods.

Price RM30

MS ISO 2818 : 1995

Plastics Preparation of test specimens by machining.

This standard establishes the general principles and procedures to

be followed when machining and notching test specimens from

compression-moulded and injection-moulded plastics, extruded

sheets, plates and partially finished or wholly finished products.

Price RM20

MS ISO 3146 : 2004

Plastics – Determination of melting behaviour (melting

temperature or melting range) of semi-crystalline polymers by

capillary tube and polarizing-microscope methods (First

revision)

This standard specifies two methods for evaluating the melting

behaviour of semi-crystalline polymers. Method A: Capillary tube.

This method is based on the changes in shape of the polymer. It is

applicable to all semi-crystalline polymers and their compounds.

Method B: Polarizing microscope. This method is based on changes

in the optical properties of the. It is applicable to polymers containing

a birefringent crystalline phase.

Price RM20

13

MS ISO 6252 : 1999

Plastics – Determination of environmental stress cracking (esc)

– Constant-tensile-stress method

Specifies methods for the determination of environmental stress

cracking (ESC) of plastics when they are subjected to a constant

tensile force in the presence of chemical agents. It is applicable to

test specimens prepared by moulding and/or machining and can be

used both for the assessment of ESC of plastics materials exposed

to different environments, and for the determination of ESC of different

plastics materials exposed to a specific environment. This standard

is identical with ISO 6252 : 1992.

Price RM20

MS ISO 6427 : 1997

Plastics – Determination of matter extractable by organic

solvents (Conventional method)

This standard specifies method for the determination of components

in plastic that can be extracted by hot organics liquids near their

boiling points. The extractable components can be monomers,

polymers, plasticizers, stabilizers, etc. The kind and percentage of

extractable matter influence the properties of plastics.

Price RM20

MS ISO 6603-1 : 2003

Plastics – Determination of puncture impact behaviour of rigid

plastics – Part 1: Non-instrumented impact testing


puncture-impact properties of rigid plastics in the form of flat test

specimens, such as discs or square pieces, under defined conditions.

Specimens may be moulded directly, cut from sheets or taken from

finished products. Different types of test specimens and test conditions

are defined.

Price RM30

MS ISO 6603-2 : 2003

Plastics - Determination of puncture impact behaviour of rigid

plastics – Part 2: Instrumented impact testing


puncture-impact properties of rigid plastics in the form of flat test

specimens, using instruments for measuring force and deflection. It

is applicable if a force-deflection or force-time diagram, recorded at

a nominally constant striker velocity, is necessary for detailed

characterization of the impact behaviour.

Price RM30

MS ISO 7111 : 1998

Plastics- Thermogravity of polymers – Temperature scanning

method.

This Malaysian Standard defines the general conditions for making

thermogravimetric measurements on polymers.

Price RM10

MS ISO 8256 : 1999

Plastics – Determination of tensile-impact strength

Specifies two methods for the determination of the energy required

to rupture test specimens of plastics under a specified tensile-impact

velocity. The tests can be described as tensile tests at comparatively

high rates of straining. Different parameters are specified depending

on the type of test specimen (see 6.1 and figure 3). This standard is

identical with ISO 8256 : 1990.

Price RM30

MS ISO 11357-1 : 1999

Plastics – Differential scanning calorimetry (DSC) – Part 1 :

General principles

Specifies a method for the thermal analysis of polymers such as

thermoplastics and thermosetting plastics, including moulding

materials and composite materials, using differential scanning

calorimetry (DSC). Various determinations can be made on polymers

by using differential scanning calorimetry. These determinations are

dealt with in parts 2 to 7 of this standard. This standard is

identical with ISO 11357-1 : 1997.

Price RM20

MS ISO 11357-2 : 2003Plastics – Differential scanning

calorimetry (DSC) – Part 2: Determination of glass transition

temperature


the characteristic glass transition temperatures of amorphous and

semi-crystalline plastics.

Price RM20

MS ISO 11357-3 : 2003

Plastics – Differential scanning calorimetry (DSC) – Part 3:

Determination of temperature and enthalpy of melting and

crystallization.


the temperature and enthalpy of melting and crystallization of

crystalline or semi-crystalline plastics.

Price RM20

MS ISO 11357-5 : 2004


Determination of characteristic reaction-curve temperatures and

times, enthalpy of reaction and degree of conversion

This standard specifies a method for the determination of reaction

temperatures and times, enthalpies of reaction and degrees of

conversion using differential scanning calorimetry (DSC). The method

applies to monomers, prepolymers in the solid or liquid state. The

material may contain fillers and/or initiators in the solid or liquid state

Price RM20

MS ISO 11357-6 : 2004


Determination of oxidation induction time

This standard specifies a method for the determination of the

oxidation-induction time (OIT) of polymeric materials by differential

scanning calorimetry (DSC). It is applicable to polyolefin resins that

are in a fully stabilised/compounded form, either as raw materials or

as finished products. It may be applicable to other plastics.

Price RM20

MS ISO 11357-7 : 2004


Determination of crystallization kinetics

This standard specifies two methods, isothermal and non-isothermal,

for studying the crystallization kinetics of partially crystalline polymers

using differential scanning calorimetry (DSC). It is only applicable to

melted polymers.

Price RM20

MS ISO 13468-1 : 2004

Plastics – Determination of the total luminous transmittance of

transparent materials – Part 1: Single-beam instrument

This standard covers the determination of the total luminious

transmittance, in the visible region of the spectrum, of planar

transparent and substantially colourless plastics, using a single-beam

photometer with a specified CIE standard light source and

photodetector. This standard cannot be used for plastics which contain

flluorecent materials. This standard is applicable to transparent

moulding materials, films and sheets not exceeding 10 mm in

thickness.

Price RM20

MS ISO 13468-2 : 2004

Plastics – Determination of the total luminous transmittance of

transparent materials – Part 2: Double-beam instrument

This standard covers the determination of the total luminous

trasmittance, in the visible region of the spectrum, of planar

transparent and substantially collourless plastics, using a double-

14

beam scanning spectro-photometer. This standard cannot be used

for plastics whuch contain fluorescent materials. This standard is

applicable to transparent moulding materials, films and sheets not

exceeding 10 mm in thickness.

Price RM20

MS ISO 13586 : 2003

Plastics – Determination of fracture toughness (GIC

KIC

) – Linear

elastics fracture mechanics (LEFM) approach

This Malaysian Standard is identical with ISO 13586:2000. This

Malaysian Standard specifies the principles for determining the

fracture toughness plastics in the crack-opening mode (mode I) under

defined conditions. Two test methods with cracked specimens are

defined, namely three-point-bending tests and compact-specimen

tensile tests in order to suit different types of equipment available or

different types of materials.

Price RM30

MS ISO 14782 : 2004

Plastics – Determination of haze for transparent materials

This standard specifies a method for the measurement of haze, an

optical property resulting from wide-angle scattering of light, in

transparent and substantially colourless plastics. This method is

applicable to the measurement of haze values of less than 40 %.

Price RM20

MS ISO 15512 : 2004

Plastics – Determination of water content

This standard specifies methods for the determination of the water

content of plastics in the form of granules and finished articles.The

methods are suitable for the determination of water content as low

as the following levels: Method A (0.1 % or better); Method B (0.01 %

or better; and Method C (0.01 % or better. Water content is an

important parameter for processing materials, and should remain

below the level specified in the approprite material standard.

Price RM20

MS ISO 15850 : 2004

Plastics – Determination of tension- Tension fatigue crack

propagation – Linear elastic fracture mechanics (LEFM)

approach

This standard specifies a method for measuring the propagation of a

crack in a notched specimen subjected to a cyclic tensile load varying

between a constant positive minimum and a constant positive

maximum value. The test results include the crack length as a function

of the load cycles and the crack length increase rate as a function of

the stress intensity factor and energy release rate at the crack tip.

The possible occurrence of discontinuities in crack propagation is

detected and reported.

Price RM30

MS ISO 16014-1 : 2004

Plastics – Determination of average molecular mass and

molecular mass distribution of polymers using size-exclusion

chromatography – Part 1: General principles

This standard specifies a general method for determining the average

molecular mass and the molecular mass distribution of polymers using

size-exclusion chromatography (SEC). The average molecular mass

and the molecular mass distribution are calculated from a calibration

curve constructed using polymer standards.

Price RM30

MS ISO 16014-2 : 2004



chromatography – Part 2: Universal calibration method

This standard specifies a method for determining the average

molecular mass and the molecular mass distribution of polymers using

size-exclusion chromatography (SEC).

The average molecular mass and the molecular mass distribution

are calculated using a universal calibration curve instead of the

conventional calibration curve.

Price RM20

MS ISO 16014-3 : 2004



chromatography – Part 3: Low-temperature method


molecular mass and the molecular mass distribution of polymers by

size-exclusion chromatography (SEC) using an organic eluent at a

temperature lower than 60 °C. The average molecular mass and the

molecular mass distribution are calculated from a calibration curve

constructed using polymer standards.

Price RM20

MS ISO 16014-4 : 2004



chromatography – Part 4: High-temperature method


molecular mass and the molecular mass distribution of polymers by

size-exclusion chromatography (SEC) using an organic eluent at a

temperature between 60 °C and 180 °C. The average molecular mass

and the molecular mass distribution are calculated from a calibration

curve constructed using polymer standards.

Price RM20

MS ISO 17281 : 2004

Plastics – Determination of fracture toughness (GIC and KIC) at

moderately high loading rates (1 m/s)

This standard provides guidelines for determining the fracture

toughness of plastics in the crack-opening mode (Mode I) by a linear

elastic fracture mechanics (LEMF) approach, at load-point

displacement rates up to 1 m/s.

Price RM30

83.080.10 Thermosetting materials

MS 1336 : 1993

Method of test for plastics-compression moulding test

specimens of thermosetting materials.

This standard specifies the general principles and the procedures to

be followed for the preparation of test specimens from thermosetting

compounds moulded under heat and pressure and for the

establishment of comparable test reports from different testing

organizations. It is applicable only to thermosetting materials based

upon phenolics, aminoplastics, melamine phenolics, expoxides and

unsaturated polyesters.

Price RM20

MS 1345 : 1993

Method of test for plastics - Determination of tensile creep.

This standard specifies a method for the determination of tensile

creep of rigid plastic materials in the form of test specimens such as

those employed for the determination of tensile properties, moulded

directly or cut from sheets.

Price RM20

MS 1349 : 1994

Method of test for plastics - Determination of flexural properties

of rigid plastics.


flexural properties of rigid non-reinforced and fibre-reinforced plastic

materials, in the form of rectangular bars of standard on non-standard

dimensions, moulded directly or cut from sheets or other shapes. It

applies only to a simple, freely supported beam, loaded at mid-span.

Price RM20

15

MS 1813 : 2005

Standard test methods for ignition loss of cured reinforced

resins

This Malaysian Standard covers the determination of the ignition loss

of cured reinforced resins. The ignition loss can be considered to be

the resin content within the limitation of 4.2. The values stated in SI

units are to regarded as the standard.

Price RM40

83.080.20 Thermoplastic materials

MS 1012 : 2003

Specification for poly(vinyl chloride) (PVC) resins (First revision)

This Malaysian Standard specifies the requirements for poly(vinyl

chloride) homopolymer resins produced by suspension

polymerisation. These resins have a nominal specific gravity of 1.4

and theoretical chlorine content of 56.8 %. This Malaysian Standard

supersedes MS 1012:1986.

Price RM20

MS 1013 : 1986

Method of test for residual vinyl chloride monomer (Gas

Chromatographic Method).

Specifies a method for the determination of residual vinyl chloride

monomer by gas chromatography in homopolymer and copolymer

resins of vinyl chloride, as well as materials and articles made from

resins.

Price RM10

MS 1267 : 1992

Method of test for plastics : Determination of the Melt Flow Index

of thermoplastics.

The determination of the melt flow index MFI according to this

standard is used for assessing the fluidity of thermoplastics under

specified conditions of pressure and temperature. The fluidity of high

polymers is dependent on the rate of shear.

Price RM10

MS 1269 : 1992

Method of test for plastics : Determination of vicat softening

temperature of thermoplastics.


of the Vicat softening temperature of thermoplastic materials:

Price RM10

MS 1303 : Part 1 : 1993

Specification for thermoplastics road marking materials : Part 1

: Requirements.

This Malaysian Standard specifies requirements for white and yellow

reflectorized thermoplastic road marking materials that are applied

to the road surface in a molten state by mechanical means.

Price RM30

MS 1334 : 1993

Method of test for plastics-compression moulding test

specimens of thermoplastics materials.

This standard specifies the general principles and the procedures to

be followed with thermoplastics in the preparation of compression-

moulded test specimens may be machined or stamped.

Price RM20

MS 1343 : Part 1 : 1993

Method of test for plastics-amorphous thermoplastics -

Preparation of test specimens with a specified maximum

reversion : Part 1 : Bars.

This Part of standard specifies procedures for the preparation of test

specimens of amorphous thermoplastic materials in the form of bars

with a specified level of uniaxial molecular orientation which is

characterized by determination of the maximum reversion. It is not

applicable to fibre reinforced thermoplastics or cellular plastics.

Price RM10

MS 1343 : Part 2 : 1993

Method of test for plastics-amorphous thermoplastics -

Preparation of test specimens with a specified maximum

reversion : Part 2 : Plates.

This Part of standard specifies procedures for the preparation of test

specimens with predominantly monoaxial orientation in the form of

rectangular plates, made from rigid amorphous thermoplastic material.

Cellular plastic materials and fibre-containing plastic materials are

excluded.

Price RM20

MS 1371 : 1995

Methods of test for environmental stress – cracking of ethylene

plastics.


the susceptibility of ethylene plastics to environmental stress –

cracking when subjected to certain condition. Under certain

conditions of stress and in the presence of environments such as

soaps, welting agents, oils or detergent, ethylene plastics may exibit

mechanical failure by cracking.

Price RM20

MS ISO 294-1 : 2002

Plastics - Injection moulding of test specimens of thermoplastics

materials - Part 1 : General principles, and moulding of

multipurpose and bar test specimens

This Malaysian Standard specifies the general principles to be

followed when injection moulding test specimens of thermoplastic

materials and gives details of mould designs for preparing two types

of specimen for use in acquiring reference data, i.e. multipurpose

test specimens as specified in ISO 3167 and 80 mm x 10 mm x 10

mm x 4 mm bars. It provides a basis for establishing reproducible

moulding conditions.

Price RM30

MS ISO 294-2 : 2002


materials - Part 2 : Small tensile bars

This Malaysian Standard specifies a four-cavity mould, the type C

ISO mould, for the injection moulding of small tensile bars measuring

> 60 mm x 10 mm x 3 mm (the type 4 test specimen in ISO 8256 :

1990).

Price RM10

MS ISO 294-3 : 2002


materials - Part 3 : Small plates

This Malaysian Standard specifies two two-cavity moulds, the type

D1 and D2 ISO moulds, for the injection moulding of small plates

measuring 60 mm x 60 mm with a preferred thickness of 1 mm (type

D1) or 2 mm (type D2) which can be used for a variety of tests (see

Annex A). The moulds may additionally be fitted with inserts for

16

volatile aromatic hydrocarbon in polystyrene. It is applicable both to

styrene homopolymers and to butadiene modified polystyrene.

Price RM10

MS ISO 2580 : Part 1 : 1994

Plastics - Acrylonitrile/Butadiene/Styrene (ABS) moulding and

extrusion materials : Part 1 : Designation

This Malaysian Standard establishes a system of designation for

arcylonitrile/butadiene/styrene (ABS) thermoplastic materials, which

may be used as the basis for specification.

Price RM10

MS ISO 2580-2 : 1999

Plastics – Acrylonitrile/butadiene/styrene (ABS) moulding and

extrusion materials - Part 2 : Preparation of test specimens and

determination of properties

Specifies the methods of preparation of test specimens and the test

methods to be used in determining the properties of ABS moulding

and extrusion materials. Requirements for handling test material and

for conditioning both the test material before moulding and the

specimens before testing are given here. This standard is identical

with ISO 2580-2 : 1994.

Price RM20

MS ISO 2897-1 : 2001

Plastics - Impact-resistant polystyrene (PS-l) moulding and

extrusion materials - Part 1 : Designation system and basis for

specifications.

This part of MS ISO 2897 establishes a system of designation for

impact-resistant polystyrene (PS-l) thermoplastic materials, which

maybe used as the basis for specifications.

Price RM10

MS ISO 2897-2 : 1999

Plastics – Impact-resistant polystyrene (PS-I) moulding and




methods to be used in determining the properties of PS-I moulding




with ISO 2897-2 : 1994.

Price RM20

MS ISO 2898-1 : 2001

Plastics - Plasticized poly (vinyl chloride) (PVC-P) moulding and

extrusion materials - Part 1 : Designation system and basis for

specifications


plasticized thermoplastic material which may be used as the basis

for specifications.

Price RM10

MS ISO 2898-2 : 1999

Plastics – Plasticized poly(vinyl chloride) (PVC-P) moulding and




methods to be used in determining the properties of PVC-P moulding



specimens before testing are given here.

Price RM20

MS ISO 4589-2 : 2000

Plastics – Determination of burning behaviour by oxygen index

– Part 2 : Ambient-temperature test

Specifies methods for determining the minimum concentration of

oxygen, in admixture with nitrogen, that will support combustion of

small vertical test specimens under specified test

studying the effects of weld lines on the mechanical properties (see

Annex B).

Price RM20

MS ISO 294-5 : 2004

Plastics – Injection moulding of test specimens of thermoplastic

materials – Part 5: Preparation of standard specimens for

investigating anisotropy

This standard specifies a two-cavity mould (designated the type F

ISO mould) for the injection moulding of 80 mm x 90 mm plates with

a preferred thickness of 3 mm. Suitable test specimens [MS ISO

527-2 type 1BA tensile test specimens or type 1 (80 mm x 10 mm)

bars] are then machined or die-cut from the plates and used to obtain

information on the anisotropy of the thermoplastic parts.

Price RM20

MS ISO 527 : Part 1 : 1994

Plastics - Determination of tensile properties : Part 1 : General

principles.

This Malaysian Standard specifies the test general principles for

determining the tensile properties of plastics and plastic composites

under defined conditions. Several different types of test specimen

are defined to suit different types of material which are detailed in

subsequent parts of this Malaysian Standard.

Price RM20

MS ISO 527 : Part 2 : 1994

Plastics - Determination of tensile properties : Part 2 : Test

conditions for moulding and extrusion plastics.

This Malaysian Standard specifies the test conditions for determining

the tensile properties of moulding and extrusion plastics, based upon

the general principles.

Price RM10

MS ISO 1158 : 2002

Plastics – Vinyl chloride homopolymers and copolymers –

Determination of chlorine content

WARNING – All precautions shall be taken, particularly those

mentioned in the text of the present Malaysian Standard, to

protect operators from risk presented by both methods.


of the chlorine content of homopolymers and copolymers of vinyl

chloride, free from plasticizers or additives, namely:

- method A (combustion in a bomb); and

- method B (combustion in a flask).

Price RM20

MS ISO 1873 : Part 1 : 1994

Plastics - Polypropylene (PP) and propylene-copolymer

thermoplastics : Part 1 : Designation.

This Malaysian Standard establishes a system of designation for

propylene (PP) thermoplastic materials, which may be used as the

basis for specifications.

Price RM10

MS ISO 1873 : Part 2 : 1994

Plastics - Polypropylene (PP) and propylene-copolymers

thermoplastics : Part 2 : Preparation of test specimens and

determination of properties.

This Malaysian Standard specifies procedures for moulding test

specimens of polypropylene materials under specified moulding

conditions and methods for measuring their properties.

Price RM10

MS ISO 2561 : 1998

Plastic –Determination of residual styrene monomer in

polystyrene by gas chomatography.


the residual styrene monomer in polystyrene by gas chromatography;

it may be used also the simultaneous determination of other

17

conditions. The results are defined as oxygen index values. This

standard is identical with ISO 4589-2 : 1996.

Price RM30

MS ISO 4610 : 2004

Plastics – Vinyl chloride homopolymer and copolymer resins –

Sieve analysis using air-jet sieve apparatus

This standard specifies a method for the determination of the retention

and particle size distribution of preferably free-flowing vinyl chloride

homopolymer and copolymer resins prepared by the “suspension”,

“bulk” and “emulsion” polymerisation processes. Control of these

characteristics can help to ensure consistency of supply and

predictable processing behaviour.

Price RM20

MS ISO 4613-2 : 1999

Plastics – Ethylene/vinyl acetate (e/vac) moulding and extrusion

materials - Part 2 : Preparation of test specimens and



methods to be used in determining the properties of E/VAC moulding




with ISO 4613-2 : 1995.

Price RM10

MS ISO 7391-1 : 2001

Plastics - Polycarbonate (PC) moulding and extrusion materials

- Part 1 : Designation system and basis for specifications.


polycarbonate thermoplastic material, which may be used as the basis

for specifications.

Price RM20

MS ISO 7391-2 : 1999

Plastics – Polycarbonate (PC) moulding and extrusion materials

- Part 2 : Preparation of test specimens and determination of

properties


methods to be used in determining the properties of polycarbonate

moulding and extrusion materials. Requirements for handling test

material and for conditioning both the test material before moulding

and the specimens before testing are given here. This standard is

identical with ISO 7391-2 : 1996.

Price RM20

MS ISO 8985 : 2000

Plastics – Ethylene/vinyl acetate copolymer (EVAC)

thermoplastics – Determination of vinyl acetate content

Specifies two categories of method for the determination of the vinyl

acetate (VAC) content of ethylene/vinyl acetate (EVAC) copolymers,

for use in the designation of such copolymers in accordance with

ISO 4613-1 : 1997. One category is referred to as ‘reference methods’,

the other as ‘test methods’. This standard is identical with ISO 8985

: 1998.

Price RM30

83.100 Cellular materials

MS 1157 : Part 38 : 2005


of adhesion to metal – Two-plate method


adhesion strength of rubber-to-metal bonds where the rubber part is

assembled between two parallel metal plates, using the adhesion

system under investigation. The method is applicable primarily to

18

test pieces prepared in the laboratory under standard conditions,

such as may be used to provide data for the development of rubber

compounds and control of methods of manufacture.

Price RM10

MS 1332 : 1993

Methods of test for flexible cellular materials-slabs-bonded and

molded urethane foams.

These methods apply to slab, bonded, and molded flexible cellular

products known as urethane foams which may be generally defined

as an expanded cellular product produced by the interaction of active

hydrogen compounds.

This standard may involve hazardous materials, operations, and

equipment.

Price RM50

MS 1528 : Part 1 : 2001

Methods of test for rigid cellular plastics materials : Part 1 :

Methods 1 to 5

This Malaysian Standard describes five methods of test applicable

to rigid cellular products for determining:

a) the dimensions; b) the apparent density; c) the compression;

d) the cross-breaking strength; and e) the dimensional stability of

cellular plastics such as polystyrene and polyurethane.

Price RM30

MS 1809 : 2005

Test methods for flexible cellular materials – Slab, bonded and

moulded urethane foams

These Malaysian Standard apply to slab, bonded and molded flexible

cellular products known as urethane foams. Urethane foam may be

generally defined as an expanded cellular product produced by the

interaction of active hydrogen compounds, water and isocynates.

Price RM40

MS 1871 : 2005

Flexible cellular polymeric materials – Determination of

compression set

This Malaysian Standard applies three methods for determining the

compression set of flexible cellular materials. At present , this standard

applies only to latex and polyurethane foams of thickness greater

than 2 mm. Methods for other materials will be added as required.

Price RM20

MS 1872 : 2005

Flexible cellular polymeric materials – Determination of

compression set under humid conditions


compression set of flexible cellular materials under humid conditions.

This method consists of maintaining the test pieces under specified

conditions of time, temperature, humidity and constant compressive

strain and determining the effect on the thickness of the test piece

after a specified recovery period.

Price RM10

MS ISO 1209-2 : 1997

Cellular plastics, rigid - Flexural tests - Part 2 : Determination of

flexural properties.

This standard specifies a method of test for determining the flexural

strength and the apparent flexural modulus of the elasticity of rigid

cellular plastics.

Price RM10

MS ISO 1926 : 1997

Cellular Plastics - Determination of tensile properties of rigid

materials.

This standard specifies a method of determining the behaviour of

rigid cellular plastics materials when they are subjected to a tensile

stress. This standard applies primary to cellular materials having a

compression resistance sufficient to permit suitable gripping of the

test pieces. In case it is impossible to grip the test piece, modify the

method in accordance with the variation described in Clause 8.

Price RM10

83.120 Reinforced Plastic

MS 1337 : 1993

Method of test for plastics-preparation of glass fibre reinforced,

resin bonded, low-pressure laminated plates or panels for test

purposes.

This standard specifies the procedure for the preparation of test plates

or panels by bonding glass cloth or mats with low-pressure

thermosetting resins. In this standard the term ’low-pressure

thermosetting resins’ relates to resins which cure at or above room

temperature either without loss of reaction products or which are not

significantly altered by loss of reaction products during cure and which

can be processed with a pressure up to 3.5 MPa.

Price RM20

MS 1418 : 1997

Specification for glass fibre - reinforced plastics underground

storage tanks for petroleum products, alcohols and alcohols-

gasoline mixtures.

These requirements cover spherical or horizontal cylindrical,

atmospheric-type tanks of glass-fibre-reinforced plastics that are

intended for the underground storage of the petroleum-based

flammable and combustible liquids, alcohols and combustible liquids,

alcohols, alcohols-blended fuels.

Price RM20

MS 1811 : 2005

Test method for short-beam strength of polymer matrix

composite materials and their laminates.

This Malaysian Standard determines the short-beam strength of high-

modules fiber-reinforced composites materials. The specimen is a

short beam machined from a curved or a flat laminate up to 6,00 mm

[0.25 in.] thick. The beam is loaded in three-point bending.

Price RM50

MS 1812 : 2005

Test methods for constituent content of composite materials

This Malaysian Standard determine the constituent content of

composite materials by one of two approaches. Method 1 physically

removes the matrix by digestion or ignition by one of seven

procedures, leaving the reinforcement essentially unaffected and thus

allowing calculation of reinforcement or matrix content (by weight or

volume) as well as percent void volume. Method II applicable only to

laminate materials of known fiber areal weight, calculates

reinforcement or matrix content (by weight or volume) based on the

measured thickness of the laminate. Method II is not applicable to

the measurement of void volume.

Price RM50

83.140 Rubber and plastics products

MS 672 : 1999

Specification of rubber seals in water supply, drainage and

sewerage pipelines (first revision)

Specifies requirements for rubber seals to be used in pipeline systems

which convey aqueous liquids at temperatures of less than 50°C.

The standard also specifies requirement for seals which incorporate

root growth inhibitor and which are only intended for the conveyance

of sewage or storm water. The standard does not specify the physical

dimensions or hardness requirements. This standard supersedes MS

672 : 1980.

Price RM40

MS 679 : 1999

Specification for latex foam rubber mattresses for domestic and

general use (First revision)

Prescribes the requirements and methods of test for mattresses made

of a latex foam rubber interior covered in a suitable ticking or proofed

sheet and intended for domestic and general use. This Malaysian

Standard does not include mattresses with interiors made from

shredded latex foam rubber. This standard supersedes MS 679 :

1980.

Price RM20

MS 773 : 1999

Specification for flexible rubber tubing and hose for use in LPG

vapour phase and LPG/air installations (First revision)

Specifies performance and dimensional requirements for rubber

tubing, hose and complete assemblies for use in LPG vapour phase

and LPG/air installations in environments up to a maximum ambient

temperature of 60°C. NOTE 1. Tubing and hoses specified in this

standard should not be used for gas cutting and allied processes

using oxygen.

NOTE 2. The abbreviation “LPG” (liquefied petroleum gas) as used

in this standard refers to butane and propane. This standard


Price RM30

MS 976 : 2004

WC seats (plastics) – Specification (First revision)

Specifies materials, design, workmanship, dimensions and

performance test requirements including impact resistance and rigidity

of the seat and cover. Interchangeability and installation including

reference to seat fastening bolts are considered.

Price RM20

MS 1151 : Part 1 : 2005

Plastics – Film and sheeting – Determination of tear resistance

– Part 1 : Trouser tear method (First revision)

This Malaysian Standard specifies a method of determining the tear

resistance of plastic film or sheet less than 1 mm thick, in the form of

standard trouser-shaped test specimens, tested under defined

conditions of pre-treatment, temperature, humidity and speed of

testing.

Price RM10

MS 1504 : 2000

Method of test for determination of thickness for flexible plastics

laminates

Specifies a method for the determination of thickness of flexible

plastics laminates by mechanical scanning method. This method is

not suitable for use with embossed flexible plastics laminates.

Price RM10

MS 1856 : 2005

Test method for environmental stress crack resistance (ESCR)

of plastics tighthead drums not exceeding 60 gal (227 l) in rated

capacity

19

This Malaysian Standard provides an indication of the environmental

stress crack resistance of plastic tighthead drums as a summation of

the effects of container design, resin, manufacturing conditions, field

performance and other factors.

Price RM40

MS 1857 : 2005

Test method for environmental stress crack resistance (ESCR)

of threaded plastics closures

This Malaysian Standard determines the susceptibility of threaded

plastic closures to failure due to environmental stress cracking (ESC)

Price RM40

MS 1858 : 2005

Rigid plastics containers – Method for determination of

drainability

This standard specifies a method for determination on the drainability

of plastic bottles and jars with a nominal capacity up to 5 l and of

plastics canisters/jerricans with a nominal volume up to 20 l.

Price RM10

MS ISO 10508 : 2004

Thermoplastics pipes and fittings for hot an cold water systems

This standard specifies the performance requirements for hot and

cold water pressure systems which use plastics pipes and plastics

or metal fittings.

Price RM30

MS ISO 11424 : 2002

Rubber hoses and tubing for air and vacuum systems for

internal-combustion engines - Specification

This Malaysian Standard specifies requirements for vulcanized-rubber

hoses and tubing for use in the various air and vacuum systems

found on internal-combustion engines.

Price RM20

MS ISO 11425 : 2004

Rubber hoses and hose assemblies for automotive power-

steering systems – Specification

Price RM20

83.140.01 Rubber and plastics products in

general

MS 671 : Part 2 : 1992

Specification for bridge bearing : Part 2 : Code of practice for

design and installation of elastomeric bridge bearing.

This Part of the Malaysian Standard gives recommendations for the

design, performance and installation of elastomeric bridge bearings.

It should be read in conjunction with MS 671 : Part 1 : The

recommendations given in this part are appropriate only when the

materials and workmanship comply with Part 1.

Price RM20

MS 773 : 1999

Specification for flexible rubber tubing and for use in LPG

vapour phase and LPG/air installations (First revision).

Specifies performance and dimensional requirements for rubber

tubing, hose and complete assemblies for use in LPG vapour phase

and LPG/air installations in environments up to a maximum ambient

temperature of 60°C.

NOTE 1. Tubing and hoses specified in this standard should not be

used for gas cutting and allied processes using oxygen.

NOTE 2. The abbreviation “LPG” (liquefied petroleum gas) as used

in this standard refers to butane and propane. This standard


Price RM30

MS 868 : 1999

Specification for natural rubber inner tubes for motorised

vehicles (first revision)

Applies to inner tubes (natural rubber) for pneumatic tyres used on

scooters, motorcycles, passenger cars, light trucks, trucks, buses

and trailers. This standard supersedes MS 868 : 1986.

Price RM20

MS 974 : 2002

Specification for rubber swimming fins (First revision)

This Malaysian Standard is applicable to rubber swimming fins used

on surface and underwater swimming for leisure purposes by free

divers, body surfers and swimmers. This standard supersedes MS

974 : 1985.

Price RM10

MS 978 : 1985

Specification for plastics waste pipe and fittings.

Covers plastic materials as stated:

(a) acrylonitrile-butadiene-styrene (ABS)

(b) modified unplasticised polyvinyl chloride (MUPVC) (c)

polypropylene (PP) (d) polyethylene (PE) intended to convey normal

domestic effluent.

Price RM40

MS 979 : Part 1 : 1985

Specification for unplasticizes sewerage pipes and fittings : Part

1 : Pipes of diameter 100 millimeter and 155 millimeter.

Specifies material, colour, dimensions and testing of products for the

conveyance of normal domestic effluents and surface water. Applies

to product laid under gardens, fields, driveway, yards and roads other

than main roads.

Price RM40

MS 979 : Part 2 : 1985

Specification for unplasticized PVC underground sewerage

pipes and fittings : Part 2 : Pipes of diameter 200 millimetres

and above.

As in Part 1 of this standard but for diameters ranging from 200mm

to 630mm.

Price RM30

MS 1082 : 1994

Specification for elastomeric teats for feeding bottles (First

revision).

This Malaysian Standard specifies requirements for materials, design,

performance, packaging and marking for elastomeric teats for babies

feeding bottles which are not cleft lip or cleft of this Malaysian Standard

specifies requirements for materials, design, performance, packaging

palate teats. This standard includes test methods and

recommendations for use and care feed teats. This standard shall

supersede MS 1082,’Specification for rubber teats for feeding bottles’.

Price RM20

MS 1106 : 1988

Specification for heavy duty polyethylene sacks.

Specifies requirements for the properties of low density film used in

the manufacture of heavy duty low density polyethylene sacks of the

pillow type, i.e. open top sacks.

Price RM20

MS 1156 : 1989

Specification for babies pacifiers.

Specifies requirements for materials, construction, design,

performance, packaging and marking for babies pacifiers. The

pacifiers, made of rubber and/or plastics materials may be constructed

as a one-piece construction, or as an assembly of separate

component parts.

Price RM20

20

mass) of plastic film. Also described in this method in the means for

calculating nominal yield, given values for nominal density and

nominal thickness. This is need since, in material specification, limits

for yield are normally stated in terms of percent deviation of actual

yield for nominal yield.

Price RM10

MS 1556 : 2002

Specification for plastics tableware

This Malaysian Standard specifies the requirements for plastics

tableware comprising plastics plates, cups, bowls and cutlery. It

includes decorated tableware.

Price RM20

MS 1557 : 2002

Specification for plastics lockable containers for household

wares

This Malaysian Standard specifies the requirements for plastics

lockable containers for household wares of round and square shape

formed by injection moulding.

Price RM20

MS 1558 : 2002

Specification for plastics food containers with lids

This Malaysian Standard specifies the requirements for plastics food

containers with lids with the capacity of 3.0 L or less. The containers

may have lids with lock, screw or interlock.

Price RM10

MS 1560 : 2002

Specification for measuring cups, spoons and litre measure for

domestic purposes

This Malaysian Standard specifies the requirements for metric cup

measures, measuring spoons, fractional cup measures and litre

measures.

Price RM20

MS 1582 : 2003

Method of test for environmental stress-crack resistance of blow-

moulded polyethylene containers

This Malaysian Standard measures the environmental stress-crack

resistance of containers, which is the summation of the influence of

container design, resin, blow-moulding conditions, post treatment,

or other factors that can affect this property. Three procedures are

provided as follows: a) Procedure A, Stress-crack resistance of

containers commercial liquids. This procedure is particularly useful

for determining the effect of container design on stress-crack

resistance of a proposed commercial package containing a proprietary

liquid product. b) Procedure B, Stress-crack resistance of a specific

container to polyoxyethylated nonylphenol, a stress-cracking agent.

This procedure is particularly useful for determining the effect of resin

on the stress-crack resistance of the container. c) Procedure C,

Controlled elevated pressure stress-crack resistance of a specific

container to polyoxyethylated nonylphenol, a stress-cracking agent.

Price RM20

MS 1593 : 2003

Method of test for environmental stress crack resistance of

plastic injection moulded open head pails

This test method provides procedures for an indication of the

environmental stress crack resistance of plastic injection moulded

open head pails, covers, and components as a summation of the

effects of container design. resin, manufacturing conditions, field

performance, and other factors. These procedures are not designed

to test the ability of the cover gasketing material or closure to retain

the test reagent. Loss or leakage of the reagent through these

openings does not constitute container failure. However. this may

indicate an internal pressure loss that might affect test results.

Price RM20

MS 1268 : 1992

Specification for high-resilience polyurethane foam.

This specification covers the minimum physical properties and other

requirements for flexible high-resilience polyurethane foam.

- Method A using a load of 10 N

- Method B using a load of 50 N

The methods specified are applicable only to thermoplastics, for which

they give a measure of the temperature at which the thermoplastics

start to soften rapidly.

Price RM10

MS 1312 : 1993

Methods of test for determination of volatile nitrosamines in

rubber teats for feeding bottles and babies pacifiers -

Dichloromethane extraction method.

This Malaysian Standard describes a method suitable for the above

determination. The dichloromethane extraction method given herein

is a development of a technique referred to in legislation in the United

States.

Price RM10

MS 1339 : 1993

Method of test for plastics - Film and sheeting-determination of

thickness by mechanical scanning.

This standard specifies a method for the determination of thickness

of a sample of plastic film or sheeting by mechanical scanning. This

method is not suitable for use with embossed film and sheeting.

Price RM10

MS 1344 : 1993

Method of test for plastics - Determination of the gas

transmission rate of films and thin sheets under atmospheric

pressure - Manometric method.

This standard specifies a method for the determination of the gas

transmission rate of plastic films and thin sheets. The limits of the

values which can be measured are from 1 to 20000 cm3/m2. The

method can be used for measurements made either with air or with

other test gases.

Price RM20

MS 1385 : 1996

Marine fenders - Specification for rubber materials.

This Malaysian Standard specifies requirements for vulcanized rubber

used in marine fenders for ports. General requirements for rubber

materials stipulated include the hardness properties, tensile strength

and elongation at break, accelerated ageing, compression set, water

absorption, ozone resistance, tear strength and abrasion resistance.

Other requirements in particular the functional tests shall be the

subject of agreement between interested parties.

Price RM20

MS 1400 : 1996

Method of test for rubber threads.

This Malaysian Standard specifies methods of test for determining

certain physical and mechanical properties of rubber threads.

Price RM20

MS 1405 : 1996

Coding system for plastics products

This Malaysian Standard specifies standard coding system for plastics

products. The purpose of this standard is to provide a system for

uniform marking of products which have been fabricated (excluding

additives, silk screening, metal-blading) from polymeric materials.

This marking system is to provide assistance in identification of

plastics products for marking subsequent decisions as to handling,

disposal or recycling.

Price RM10

MS 1424 : 1997

Method of test for package yield of plastic film.

This test method covers the determination of yield (area per unit

21

MS 1594 : 2003

Method of test for column crush properties of blown

thermoplastic containers.


mechanical properties of blown thermoplastic containers when loaded

under columnar crush conditions at a constant rate of compressive

deflection. Any container. whether blown commercially or in the

laboratory, may be used as the test specimen.

Price RM20

MS 1733 : 2004

Plastics - Guidelines on packaging in plastics containers

This Malaysian Standard provides guidelines on packaging in

containers made of plastics materials.

Price RM20

MS 1734 : 2004

Plastics - Film and sheeting - Determination of oxygen gas

transmission rate using a coulometric sensor

This Malaysian Standard prescribes method for determination of the

steady-state rate of transmission of oxygen gas through plastics in

the form of film, sheeting, laminates, coextrusions, or plastics-coated

papers or fabrics. The method is used to determine:

a) oxygen gas transmission rate (O2GTR);

b) the permeance of the film to oxygen gas (PO2); and

c) oxygen permeability coefficient (PO2); in the case of

homogenous materials.

Price RM20

MS 1735 : 2004

Plastics - Blow-moulded thermoplastic containers -

Determination of drop impact resistance

This test method provides measures of the drop impact resistance

of blow-moulded thermoplastic containers as a summation of the

effects of material, manufacturing conditions, container design, and

perhaps other factors.

Price RM20

MS 1769 : 2004

Portable cooler boxes – Specification

This standard specifies the requirements for portable cooler boxes

whose main body is principally made of plastics, with the addition of

heat-insulating material, used for recreation such as outdoor activities,

etc. generally to keep contents of the portable cooler boxes cool.

Price RM10

MS 1770 : 2004

Plastics films – Guidelines on the use for stretch wrapping

This Malaysian Standard provides general guidance on the use of

plastics films for stretch wrapping of individual and unit loads

packages.

Price RM20

MS 1771 : 2004

Plastics films – Guidelines on the use for shrink wrapping

This standard provides general guidance on the use of plastics films

for shrink wrapping of individual and unit load packages.

Price RM20

MS ISO 6427 : 1997

Plastics - Determination of matter extractable by organic

solvents (Conventional method).

This standard specifies method for the determination of components

in plastic that can be extracted by hot organics liquids near their

boiling points. The extractable components can be monomers,

polymers, plasticizers, stabilizers, etc. The kind and percentage of

extractable matter influence the properties of plastics.

Price RM20

22

83.140.10 Films and sheets

_____________________________________________

MS 602 : 1979

Specification for flexible, unsupported thick PVC sheeting.

For 6 types of sheeting ranging from 0.25mm to 1mm. Covers

definitions, stiffness, colour fastness, colour bleeding, adhesion of

print, ply adhesion, retention of embossed surfaces, blocking, strength

and dimension requirements. Test methods appended.

Price RM30

MS 681 : 1980

Specification for PVC film.

Provides four standard types of film : Type 1, Type 2, Type 1F and

Type 2F. Gives requirements for visual examination, pinholes,

thickness, colour bleeding, adhesion of print, ply adhesion, retention

of embossed surface, blocking, ageing, colour fastness and

flammability. Sampling and test methods appended.

Price RM30

MS 1105 : 1988

Method of test for impact resistance of polyethylene film by the

free-falling dart method.

Covers the determination of the energy that causes polyethylene

film to fail under specified conditions of impact of a free falling dart.

This energy is expressed in terms of the weight (Mass) of the missile

falling from a specified height which would result in 50% failure of

specimen tested.

Price RM20

MS 1150 : 1989

Method of test for determination of coefficients of friction of

plastics film.

Describes a procedure for determining the static and kinetic

coefficients of friction of a plastic film when sliding over itself at specific

test conditions.

Price RM10

MS 1151 : 1989

Method of test for tear resistance of plastics film and sheeting

(Trouser tear method).

Specifies a method of test for tear resistance of plastics film on sheet

less than 1mm thick, in the form of standard trouser-shaped test

specimens, tested under defined conditions of pretreatment,

temperature, humidity and speed of testing.

Price RM10

MS 1151 : Part 2 : 1992

Method of test for tear resistance of plastics film and sheeting :

Part 2 : Elmendort method.

This Malaysian Standard is the second part of the MOT for tear

resistance of plastics film and sheeting MS 1151. This Part of

Malaysian Standard specifies a method of determining the force

required to propagate a tear through a specified distance and from a

specified slit, cut in a test specimen of thin flexible plastic sheeting or

film, under specified conditions of loading. Materials that can be tested

according to this method include flexible polyvinyl chloride (PVC)

and polyolefin films.

Price RM20

MS 1509 : 2000

Method of test for film hardness of an organic coating by pencil

test

Specifies a procedure for rapid, inexpensive determination of the

film hardness of an organic coating on a substrate in terms of drawing

leads or pencil leads of known hardness.

Price RM10

MS 1559 : 2002

Method of test for permeability of thermoplastic containers to

packaged reagents or proprietary products

This test method covers procedures for determining the permeability

of thermoplastic containers to packaged reagents or proprietary

products under specified conditions of exposure. The exposures used

are intended to simulate the normal and elevated temperature–

storage condition that might be encountered in end–use application.

Price RM20

MS 1772 : Part 1 : 2004

Flexible packaging material – Determination of residual solvents

by static headspace gas chromatography: Part 1: Absolute

methods

This standard describes methods for the quantitative determination

of residual solvents in flexible packaging by static headspace

chromatography. The chemical identities of the residual solvents to

be determined by this method must be known before commencing

the analysis. During the analysis there may be interferences from

possible products of thermal decomposition. Residues from thermal

decomposition products are not within the scope of this standard.

Additional peaks due to these products shall not be considered for

evaluation of residual solvents. This method is applicable to flexible

packaging materials that may consist of mono- or multiplayer plastic

film, paper or board, foil or combination thereof. The method does

not apply to residual solvents with amounts lower than 0.5 mg/m3.

Price RM20

MS 1772 : Part 2 : 2004

Flexible packaging material – Determination of residual solvents

by static headspace gas chromatography: Part 2: Industrial

methods

This standard describes rapid methods as commonly used in quality

control for example for monitoring the level of residual solvent used

in the production of flexible packaging by static headspace

chromatography. The procedure described involves one single

injection of the headspace which implies an incomplete extraction of

the solvent. The values obtained may be lower than the absolute

content. During the analysis there may be interferences from possible

products of thermal decomposition. Residues from thermal

decomposition products are not within the scope of this standard.

Additional peaks due to these products shall not be considered for

evaluation of residual solvents

Price RM20

MS 1805 : 2005

Test method for resistance of plastics films to extraction by

chemicals

This Malaysian Standard covers the measurement of the weight loss

of film after immersion in chemicals.

Price RM40

MS 1806 : 2005

Test method for puncture-propagation tear resistance of plastics

film and thin sheeting

This Malaysian Standard covers the determination of the dynamic

tear resistance of plastic film and thin sheeting subjected to end-use

snagging-type hazards.

Price RM50

MS 1420 : 1997

Method of test for wetting tension of plastic film and sheeting.


wetting tension of surfaces for plastics film and sheeting in contacts

with drops of specific test solution.

Price RM10

MS 1422 : 1997

Method of test for unstrained linear thermal shrinkage of plastics

film and sheeting.

This test method covers the determination of the degree unstrainded

linear thermal shrinkage at given specimen temperature of plastic

films and sheeting of 0.76 mm thickness or less. This test method

does not cover shrinkage from loss of solvent in some materials.

Price RM10

MS 1423 : 1997

Method of test for blocking of plastics film - Parallel plate method.

This test method yields quantitative information regarding the degree

of blocking (unwanted adhesion) existing between layers of plastics

film. It is not intended to measure susceptibility to blocking.

Price RM20

MS 1424 : 1997

Method of test for package yield of plastic film.

This test method covers the determination of yield (area per unit

mass)of plastic film. Also described in this method in the means for

calculating nominal yield, given values for nominal density and

nominal thickness. This is need since, in material specification, limits

for yield are normally stated in terms of percent deviation of actual

yield for nominal yield.

Price RM10

MS 1477 : 1999

Specification for polyethylene film and sheeting

Specifies the classification of polyethylene film and sheeting up to

and including 300 mm (0.3 mm) in thickness. The film or sheeting

may contain additives for the improvement of the surface properties,

pigments or stabilisers.

Price RM20

MS 1478 : 1999

Specification for low-density polyethylene films for general use

and packaging applications

Specifies unpigmented, unsupported tubular, low-density

polyethylene films (hereafter referred to as film or films) from resins

having densities ranging from 910.0 kg/m3 to and including 925.0 kg/

m3 (0.910 g/cm3 to and including 0.925 g/cm3), as measured on

moulded plaques.

Price RM20

MS 1479 : 1999

Specification for polyethylene sheeting for construction,

industrial and agricultural applications

Specifies polyethylene sheeting, 250 mm or less in thickness,

intended for construction, industrial and agricultural applications.

Price RM20

MS 1505 : 2005

Test method for comparison of bond strength or ply adhesion

of similar laminates made from flexible materials (First revision)

This Malaysian Standard covers a procedure for comparing the bond

strength or ply adhesion of similar laminates made from flexible

materials such as cellulose, paper, plastic film and foil. This includes

laminates made by various processes : adhesive laminates, extrusion

coatings, extrusion laminates and coextrusion.

Price RM40

23

MS 1807 : 2005

Test method for shrink tension and orientation release stress

of plastics film and thin sheeting

This Malaysian Standard covers the determination of the shrink

tension and related characteristics that is shrink force and orientation

release stress, of heat-shrinkable plastic film and sheeting of less

than 1,0 mm (0.04 in.) thickness. Two procedures are described that

permit the measurement of shrink forces at predetermined

temperature.

Price RM40

MS 1896 : 2005

Test method for evaluating load containment performance of

stretch wrap films by vibration testing

This Malaysian Standard is used to evaluate and compare the ability

of stretch-wrap films to contain unitized loads during shipping.

Price RM40

MS 1897 : 2005

Test method for evaluating abrasion resistance of stretch wrap

films by vibration testing

This Malaysian Standard compares the abrasion resistance of similar

types of stretch wrap films.

Price RM40

MS 1898 : 2005

Test method for protrusion puncture resistance of stretch wrap

film

This Malaysian Standard determines the resistance of a stretch wrap

film to the penetration of a probe at a standard low rate, a single test

velocity. Performed at standard conditions, the test method imparts

a biaxial stress that is representative of the type of a stress

encountered in many product end-use applications.

Price RM40

MS 1899 : 2005

Test methods for hot seal strength (hot tack) of thermoplastic

polymers and blends comprising the sealing surfaces of flexible

webs

This Malaysian Standard cover laboratory measurement of the

strength of heatseals formed between thermoplastic surfaces of

flexible webs, immediately after a seal has been made and before it

cools to ambient temperature.

Price RM40

MS 2000 : 2005

Test method for water vapour transmission rate through plastics

film and sheeting using a modulated infrared sensor

This Malaysian Standard covers a procedure for determining the

rate of water vapor transmission through flexible barrier materials.

Price RM50

MS 2001 : 2005

Test method for peel cling of stretch wrap film

This Malaysian standard measures cling between two layers of film,

in both a stretched and unstretched conditions.

Price RM50

MS ISO 527-3 : 2001

Plastics - Determination of tensile properties - Part 3 : Test

conditions for films and sheets

This part of MS ISO 527 specifies the conditions for determining the

tensile properties of plastic films or sheets less than 1 mm thick,

based upon the general principles given in part 1. This standard

supersedes MS 1152 : 1989

Price RM10

MS ISO 527-4 : 2001


conditions for isotropic and orthotropic fibre-reinforced plastic

composites

This part of MS ISO 527 specifies the test conditions for the

determination of the tensile properties of isotropic and orthotropic

24

fibre reinforced plastic composites, based upon the general principles

given in part 1. Unidirectionally reinforced materials are covered by

part 5.

Price RM20

MS ISO 527-5 : 2001


conditions for unidirectional fibre-reinforced plastic composites

This part of MS ISO 527 specifies the test conditions for the

determination of the tensile properties of unidirectional fibre-reinforced

plastic composites, based upon the general principles given in part 1.

Price RM20

MS ISO 2528 : 2000

Sheet materials - Determination of water vapour transmission

rate - Gravimetric (dish) method

Specifies a method for the determination of the water vapour

transmission rate (often erroneously called “permeability” of sheet

materials. This method is not generally recommended for use if the

transmission rate is expected to be less than 1 g/m2.d) or for materials

thicker than 3 mm.

Price RM20

MS ISO 8570 : 2004

Plastics – Film and sheeting – Determination of cold-crack

temperature

This standard specifies a method for assessing the brittleness of

plastic film and sheeting at low temperature. The assessment is given

in the form of a conventional cold- crack temperature which serves

as a guidelines for comparing the low-temperature behaviour of

plastics film and sheeting.

Price RM20

whether or not intended for human consumption, (domestic systems)

and for heating systems, under design pressures and temperatures

appropriate to the class of application.

Price RM20

MS 1736 : Part 5 : 2004

Plastics piping systems for hot and cold water installations -

Crosslinked polyethylene (PE-X) : Part 5 : Fitness for purposes

of the system

This standard specifies the characteristics of the fitness for purpose

of crosslinked polyethylene (PE-X) piping systems, intended to be

used for hot and cold water installations within buildings for the

conveyance of water whether or not intended for human consumption

(domestic systems) and for heating systems, under design pressures

and temperatures according to the class of application.

Price RM20

MS 1736 : Part 7 : 2004


Crosslinked polyethylene (PE-X): Part 7: Guidance for the

assessment of conformity

This Technical Specification gives guidance for the assessment of

conformity to be included in the manufacturer’s quality plan as part

of his quality system.

Price RM50

MS 1737 : 2004

Plastics piping systems- Guidance for the installation inside

buildings of pressure piping systems for hot and cold water

intended for human consumption.

This standard recommends practices to be followed in the application

and installation of thermoplastics pipes and associated fittings.

Price RM30

MS 1738 : 2004

Plastics piping systems - Injection-moulded thermoplastics

fittings, valves and ancillary equipment - Determination of the

long-term hydrostatic strength of thermoplastics materials for

injection moulding of piping components.

This standard specifies method for preparing tubular test pieces for

testing thermoplastics materials used for injection moulding, to

evaluate the long term resistance to constant internal water pressure

at constant temperature and to check the hydrostatic strength of the

material.

Price RM10

MS 1739 : 2004

Plastics piping systems - Thermoplastics pipes and fittings for

hot and cold water - Test method for the resistance of mounted

assemblies to temperature cycling

This Malaysian Standard specifies a method for testing the resistance

to temperature cycling of joints for piping systems with rigid or flexible

thermoplastics pipes. It is applicable to thermoplastics piping systems

intended to be used in hot and cold water pressure applications.

Price RM10

83.140.30 Plastics pipes, fittings and valves

MS 978 : 1985

Specification for plastics waste pipe and fittings.

Covers plastic materials as stated:

(a) acrylonitrile-butadiene-styrene (ABS)

(b) modified unplasticised polyvinyl chloride (MUPVC)

(c) polypropylene (PP)

(d) polyethylene (PE) intended to convey normal domestic

effluent.

Price RM40

MS 979 : Part 1 : 1985


pipes and fittings : Part 1 : Pipes of diameter 100 millimeter and

155 millimeter.

Specifies material, colour, dimensions and testing of products for the

conveyance of normal domestic effluents and surface water. Applies

to product laid under gardens, fields, driveway, yards and roads other

than main roads.

Price RM40

MS 979 : Part 2 : 1985


pipes and fittings : Part 2 : Pipes of diameter 200 millimetres

and above.

As in Part 1 of this standard but for diameters ranging from 200 mm

to 630 mm.

Price RM30

MS 1010 : 1986

Specification for rigid polyvinyl chloride and related plastic pipe

and fittings compounds.

This Malaysian Standard specifies the physical requirements and

test methods for the rigid vinyl chloride compounds for pipes and

fittings. The compounding ingredients may consist of lubricants,

stabilizers, (vinyl chloride), resin modifiers, pigments and inorganic

fillers.

Price RM30

MS 1736 : Part 1 : 2004

Plastics piping systems for hot and cold water installations –

Crosslinked polyethylene (PE-X): Part 1: General

This Malaysian Standard specifies the general aspects of crosslinked

polyethylene (PE-X) piping systems intended to be used for hot and

cold water installations within buildings for the conveyance of water,

whether or not intended for human consumption (domestic systems),


according to the class of application.

Price RM20

MS 1736 : Part 2 : 2004

Plastics piping systems for hot and cold water Installations -

Crosslinked polyethylene (PE-X) : Part 2 : Pipes

This Malaysian Standard specifies the Characteristics of pipes made

from crosslinked polyethylene (PE-X) for piping systems intended to

be used for hot and cold water installations within buildings for the

conveyance of water, whether or not intended for human consumption

(domestic systems), and for heating systems, under design pressures

and temperatures appropriate to the class of application.

Price RM20

MS 1736 : Part 3 : 2004


Crosslinked polyehtylene (PE-X) : Part 3 : Fittings

This standard specifies the characteristics of fittings for crosslinked

polyethylene (PE-X) piping systems intended to be used for hot and

cold water installations within buildings for the conveyance of water

25

MS 1740 : 2004

Thermoplastics piping systems - End-load bearing mechanical

joints between pressure pipes and fittings - Test method for

resistance to pull out under constant longitudinal force

This Malaysian Standard specifies a method for checking the ability

of assembled end-load bearing mechanical joints (excluding fusion-

welded joints) between fittings and pressure pipes to withstand a

longitudinal tensile force.

Price RM10

MS 1741 : 2004

Plastics piping systems - Mechanical joints between fittings and

polyolefin pressure pipes - Test method for leaktightness under

internal pressure of assemblies subjected to bending

This standard specifies a method for checking the leaktighness under

internal hydrostatic pressure of assembled mechanical joints

(excluding fusion-welded joints) between fittings and polyolefins

pressure pipes while subjected to bending.

Price RM10

MS 1761 : 2004

Plastics pipes and fittings – Determination of the opacity


opacity of plastics pipes and fittings.

Price RM10

MS ISO 15876-1 : 2004

Plastics piping systems for hot and cold water installations-

Polybutylene (PB)- Part 1 : General

This Part of prEN ISO 15876 specifies the general aspects of

polybutylene (PB) piping systems intended to used for hot and cold

water installations within buildings for the conveyance of water

whether or not intended for human consumption (domestic systems)


according to the class of application .

Price RM20

MS ISO 15876-2 : 2004


Polybutylene (PB) - Part 2 : Pipes

This Part prEN ISO 15876 specifies the characteristics of pipes made

of polybutylene (PB) for piping systems intended to be used for hot

and cold water installations within buildings for the conveyance of

water whether or not intended for human consumption (domestic

systems), and for heating systems, under design pressure and

temperatures appropriate to the class of application.

Price RM30

MS ISO 15876-3 : 2004


Polybutylene (PB) - Part 3 : Fittings

This Part of prEN ISO 15876 specifies the characteristics of fittings

for polypropylene (PB) piping systems intended to be used for hot

and cold water installations within buildings for the conveyance of

water, whether or not intended for human consumption (domestic

systems) and for heating systems under design pressure and

temperature according to the class of application.

Price RM30

MS ISO 15876-5 : 2004


Polybutylene (PB)- Part 5 : Fitness for purpose of the system

This Part of prEN ISO 15876 specifies the characteristic of the fitness

for purpose of polybutylene (PB) piping systems, intended to be used

for hot and cold water installations within buildings for the conveyance

of water, whether or not intended for human consumption, (domestic

systems) and for heating systems, under design pressures and

temperatures according to the class of application.

Price RM20

26

MS ISO 15876-7 : 2004

Plastics piping systems for hot and cold water installation -

Polybutylene (PB)- Part 7: Guidance for the assessment of

conformity

This technical Specification gives guidance for the assessment of

conformity to be included in the manufacturer’s quality plan as part

of his quality system.

Price RM30

83.140.40 Hoses

MS 773 : 1999

Specification for flexible rubber tubing and hose (including

connections where fitted and safety recommendations) for use

in LPG vapour phase and LPG/air installations.

Covers performance and dimensional requirements and safe

operations for flexible tubing used in installations not exceeding 17.5

bar. Excludes tubings for gas cutting and welding applications. Tests

include resistance to KinKing crushing ageing and burst to substances

such as ozone and pentane.

Price RM30

MS 1070 : 2002

Specification for rubber radiator hoses for automotive internal

combustion engine (first revision)

This standard specifies the requirements of rubber hoses for use in

the cooling system of automotive internal combustion engines.

Note: The hoses shall be used in positions where they are not likely

to be subjected to outside surface contamination by fuel and

lubricating oils. This standard supersedes MS 1070: 1987.

Price RM20

MS 1545 : 2002

Rubber hoses for agricultural spraying

This Malaysian Standard specifies requirements for three types of

flexible rubber hose for pressure spraying of agropharmaceutical and/

or fertilizer products within a temperature range of -10 °C to + 60 °C.

Price RM10

MS ISO 1403 : 2002

Rubber hoses, textile-reinforced, for general-purpose water

applications - Specification

This Malaysian Standard specifies the requirements for three types

of general-purpose textile-reinforced rubber water hose with an

operating range of -25°C to + 70°C, and a maximum working pressure

of up to 2,5 MPa.

Price RM10

MS ISO 3821 : 2002

Gas welding equipment - Rubber hoses for welding, cutting and

allied processes

This Malaysian Standard specifies requirements for rubber hoses

(including twin hoses) for welding, cutting and allied processes. The

term “allied processes” means, in particular, heating, brazing and

metallization.

Price RM20

MS 1068 : 2002

Specification for rubber floor mats for vehicles (First revision)

This Malaysian Standard applies to floor mats made of rubber

intended for use in motor vehicles and electric vehicles. This standard


Price RM10

MS 1155 : 2003

Single-use medical examination gloves – Specification

This Malaysian Standard specifies requirements for packaged sterile,

or bulked non-sterile, rubber gloves intended for use in medical

examinations and diagnostic or therapeutic procedures to protect

the patient and the user from cross-contamination. It also covers

rubber gloves intended for use in handling contaminated medical

materials and gloves with smooth surfaces or with textured surfaces

over part or all of the glove. This standard is intended as a reference

for the performance and safety of rubber examination gloves. The

safe and proper usage of examination gloves and sterilisation

procedures with subsequent handling, packaging and storage

procedures are outside the scope of this standard.

Price RM20

MS 1225 : Part 1 : 2004

Plastics - Polyethylene (PE) tanks for cold water storage - Part

1 : Capacity up to 600 gal (First revision)

This Malaysian Standard specifies requirements for materials,

physical properties and performance of polyethylene tank up to 600

gal capacity, used for cold water storage.

Price RM30

MS 1225 : Part 2 : 2006

Polyethylene (PE) tanks for cold water storage – Part 2 : Capacity

more than 600 gal (First revision)

This Malaysian Standard specifies requirements for materials,

physical properties and performance of polyethylene tank more than

600 Imperial Gallons (2730 L) capacity, used for cold water storage.

Price RM30

MS 1291 : 2003

Single-use sterile rubber surgical gloves – Specification

This Malaysian Standard specifies requirements for packaged sterile

rubber gloves intended for use in surgical procedures to protect the

patient and the user from cross-contamination. It is applicable to

single-use gloves that are worn once and the discarded. It does not

apply to examination or procedure gloves. It covers gloves with

smooth surfaces and gloves with textured surfaces over part or all of

the glove. This standard is intended as a reference for the

performance and safety of rubber surgical gloves. The safe and proper

usage of surgical gloves and sterilisation procedures with subsequent

handling, packaging and storage procedures are outside the scope

of this Malaysian Standard.

Price RM20

MS 1407 : Part 1 : 1996

Specification for plastics containers: Part 1 : Screw thread

finishes for plastics containers.

This Malaysian Standard specifies plastics used as receptable of

standards design for the transport of standards design for the transport

of goods for packaging of liquids, powder and pellets.

Price RM30

MS 1407 : Part 2 : 1996

Specification for plastics containers: Part 2 : Capacity, mass

and tolerances on dimensions for plastics containers having

capacity of less than 5 liters.

This part of the Malaysian Standard specifies tolerances on capacities,

mass and dimensions for plastics containers having capacity of less

than 5 liters.

Price RM30

MS ISO 4642 : 2004

Rubber products – Hoses, non-collapsible, for fire-fighting

service

Price RM10

83.140.50 Seals

MS 672 : 1999

Specification of rubber seals in water supply, drainage and

sewerage pipelines (first revision)

Specifies requirements for rubber seals to be used in pipeline systems

which convey aqueous liquids at temperatures of less than 50°C.

The standard also specifies requirement for seals which incorporate

root growth inhibitor and which are only intended for the conveyance

of sewage or storm water. The standard does not specify the physical

dimensions or hardness requirements. This standard supersedes

MS 672 : 1980.

Price RM40

83.140.99 Other rubber and plastics products

MS 676 : 2001

Specification for plastics buckets (First revision)

This Malaysian Standard specifies the requirements for plastic

buckets of all shapes (including lids, if any) formed by injection

moulding process. This standard supersedes MS 676 : 1980.

Price RM10

MS 679 : 1999

Specification for latex foam rubber mattresses for domestic and

general use (First revision).

Prescribes the requirements and methods of test for mattresses made

of a latex foam rubber interior covered in a suitable ticking or proofed

sheet and intended for domestic and general use. This Malaysian

Standard does not include mattresses with interiors made from

shredded latex foam rubber. This standard supersedes MS 679 :

1980.

NOTE: Developed by Malaysian Rubber Board (SWO).

Price RM20

MS 735 : 1996

Specification for plastics feeding bottles (First revision).

This Malaysian Standard is the first revision of MS 735 : 1981. This

revision prescribes requirements and method of test for plastics

feeding bottles. Amongst the requirements specified in this standard

are materials, design, performance, packaging and marking. The

major amendments incorporated in this revision are the requirements

for heavy metals in the plastics components parts of the feeding

bottles and minimum scale marks for the bottles. This standard shall

supersede MS 735 : 1981.

Price RM20

MS 973 : 2002

Specification for rubber bands (First revision)

This Malaysian Standard covers rubber bands for general purposes

and does not cover sealing rings used for sealing purpose, or

transmission belts, used for transmitting mechanical power

continuously. This standard supersedes MS 973 : 1985.

Price RM10

27

MS 1407 : Part 3 : 2001

Specification for plastics containers : Part 3 : Container over 5

L up to and including 60 L capacity

This part of this Malaysian Standard specifies tolerances on

dimensions and performance requirements for free standing blow

moulded containers with capacities over 5 L up to and including 60L.

Price RM30

MS 1407 : Part 4 : 2001

Specification for plastics containers : Part 4 : Drums over 70 L

up to including 250 L capacity

This part of this Malaysian Standard specifies the capacity, mass

and tolerances on dimensions for blow moulded drums having

capacity over 70 L up to and including 250 L.

Price RM20

MS 1502 : 2000

Specification for disposable polystyrene cutlery

Specifies material and performance requirements for disposable

polystyrene cutlery which are intended for use in contact with food

and drinks up to a maximum service temperature of 100 °C.

Price RM30

MS 1510 : 2000

Specification for polystyrene cushioning foams

Specifies expandable polystyrene foam used as package cushioning

material. It does not cover polystyrene foam in chip or granular form.

Price RM20

MS 1521 : 2001

Specification for polyolefin woven open-mouth sacks

This Malaysian Standard specifies requirements for the materials,

dimensions and performance of open-mouth sacks manufactured

from plain weave fabrics produced from polyolefin tape yarns.

Price RM20

MS 1530 : 2001

Specification for plastics washing basins

This Malaysian Standard specifies the requirements for plastic

washing basins for domestic use.

Price RM10

MS 1564 : Part 1 : 2003

Mobile waste containers: Part 1: Containers with two wheels

with a capacity from 80 L to 1 390 L for comb lifting devices –

Dimensions and design

Price RM30

MS 1564 : Part 2 : 2003

Mobile waste containers: Part 2: Containers with four wheels

with a capacity 500 L to 1 200 L with flat lid(s), for trunnion and/

or comb lifting devices – Dimensions and design

Price RM30

MS 1564 : Part 3 : 2002


with a capacity from 770 L to 1 300 L with dome lid(s), for trunnion

and/or comb lifting devices – Dimensions and design

This Malaysian Standard specifies dimensions and design

requirements of mobile waste containers with four wheels, with dome

lid(s) and capacity from 770 L to 1 300 L to be used by trunnion and/

or comb lifting device.

Price RM30

MS 1564 : Part 4 : 2002


with a capacity from 750 L to 1 700 L with flat lid/(s), for wide

28

trunnion or BG – Lifting device and/or wide comb lifting devices

– Dimensions and design

This Malaysian Standard specifies dimensions and design

requirements of mobile waste containers with four wheels, with flat

lid(s) and capacity from 750 L to 1 700 L to be used by wide trunnion

or BG–lifting device and/or wide comb lifting device.

Price RM30

MS 1564 : Part 5 : 2002

Specifications for mobile waste containers: Part 5: Performance

requirements and test methods

This Malaysian Standard prescribes the test methods and the

requirements for mobile waste containers specified in MS 1564:

Part 1 to MS 1564: Part 4. This standard is applicable to plastics

and metal mobile waste containers with capacities from 80 L to

1,700 L.

Price RM20

MS 1564 : Part 6 : 2002

Specifications for mobile waste containers: Part 6: Safety and

health requirements

This Malaysian Standard provides the most essential safety and

health requirements for plastics and metal mobile waste containers,

not including hazardous wastes containers.

Price RM10

83.160 Tyres

MS 150 : 1999

Standard practice for determination of bead unseating

resistance of a tubeless passenger car tyre (First revision)

Covers the determination of force required to completely dislodge

the bead of an inflated tubeless passenger car tyre from its rim as

indicated by a loss of inflation pressure or a sudden drop in bead

unseating force as exerted by a bead unseating block.

Price RM10

MS 224 : 2005

Retreaded pneumatic rubber tyres for passenger cars and

commercial vehicles – Specification (Second revision)

This Malaysian Standard specifies requirements for retreading of

pneumatic highway tyres including passenger car tyres and tyres

for multi-purpose passenger vehicles, trucks, buses, trailers and

other commercial vehicles used on the public road.

Price RM20

Best Seller

- Method A, using a trouser test piece; - Method B, using an angle

test piece, with or without a nick of specified depth; and- Method C,

using a crescent test piece with a nick. This standard supersedes

MS 1157: Part 6: 1994.

Price RM20

MS ISO 1629 : 2004

Rubber and lattices – Nomenclature

Price RM10

MS ISO 4570-1 : 2002

Tyre valve threads - Part l : Threads 5V1, 5V2, 6V1 and 8V1

This Malaysian Standard specifies limit dimensions and tolerances

for tyre valve threads 5V1, 5V2, 6V1 and 8V1.

Price RM10

MS ISO 4570-2 : 2002

Tyre valve threads - Part ll : Threads 9V1, 10V2, 12V1 and 13V1


for tyre valve threads 9V1, 10V2, 12V1 and 13V1.

Price RM10

MS ISO 4570-3 : 2002

Tyre valve threads - Part 3 : Threads 8V2, 10V1, 11V1, 13V2,

15V1, 16V1, 17V1, 17V2, 17V3, 19V1, 20V1


for tyre valve threads 8V2, 10V1, 11V1, 13V2, 15V1, 16V1, 17V1,

17V2, 17V3, 19V1 and 20V1.

Price RM20

MS ISO 6762 : 2002

Tyre valves - ISO core chamber No. 2

This Malaysian Standard specifies the interchangeability dimensions

of an ISO core chamber No. 2 (large bore), and applies principally to

core chambers of valves used on tyres for agricultural machines,

earth-moving machines and civil aircraft.

Price RM10

MS ISO 9413 : 2002

Tyre valves - Dimensions and designation

This Malaysian Standard defines the essential dimensions and the

designation of tube valves and tubeless valves.

Price RM80

83.160.10 Road vehicle tyres

MS 148 : Part 1 : 1973

Specification for tyre and wheel data : Part 1 : Pneumatic rubber

tyres.

Applies to pneumatic rubber tyres for passenger cars and gives

recommended tyre size with loads and inflation pressure schedules.

Requirements for marking and test procedures included.

Price RM30

MS 868 : 1999

Specification for natural rubber inner tubes for motorised

vehicles (first revision)

Applies to inner tubes (natural rubber) for pneumatic tyres used on

scooters, motorcycles, passenger cars, light trucks, trucks, buses

and trailers. This standard supersedes MS 868 : 1986.

Price RM20

MS 1443 : 1998

Standard test apparatus for using a nominal 1707 mm diameter

laboratory test roadwheel in testing tyres.

This practice describes the requirements for a 1707 mm diameter

laboratory roadwheel for durability testing of tyres under controlled

operating environmental conditions.

Price RM10

MS 1444 : 1998

Standard test method for energy absorbed by a tyre when

deformed by a slow moving plunger.

This standard covers the determination of tyre plunger energy

required to completely penetrate the tread area of an inflated tyre as

indicate by a rapture, loss of inflation pressure, sudden drop in plunger

force or bottom –out. The test requires utilisation of a laboratory testing

machine equipped with a slow-moving plunger which has a

hemispherical end.

Price RM10

MS 1478 : 1999

Specification for low-density polyethylene films for general use

and packaging applications

Specifies unpigmented, unsupported tubular, low-density

polyethylene films (hereafter referred to as film or films) from resins

having densities ranging from 910.0 kg/m3 to and including 925.0 kg/

m3 (0.910 g/cm3 to and including 0.925 g/cm3), as measured on

moulded plaques. This specification is applicable to homopolymer

polyethylene, but is not restricted to it.

Price RM20

MS 1479 : 1999

Specification for polyethylene sheeting for construction,

industrial and agricultural applications

Specifies polyethylene sheeting, 250 mm or less in thickness,

intended for construction, industrial and agricultural applications.

Price RM20

MS 1565 : 2002

Motorcycle tyre dimensions and rims (Inch code – Designated

series)

This Malaysian Standard sets out the designations in use and the

dimensions for inch code designated series of motorcycle tyres. This

Malaysian Standard applies to motorcycle tyres used on highway

and off the road service with a speed rating of not exceeding 240

km/h and fitted on rims with normal diameters corresponding to the

codes 14, 15, 16, 17, 18, 19, 21 and 23 inches.

Price RM20

MS 1566 : 2002

Definitions of common terms used in the tyres industry – Solid

tyres

This Malaysian Standard describes the definitions of common terms

relating to solid tyres, as used in the tyres industry. This Malaysian

Standard does not include pneumatic tyres which are within the scope

of “MS 1439: 1998 – Definitions of common terms used in the tyre

industry – Pneumatic tyres”.

Price RM10

MS 1567 : Part 1 : 2002

Rubber, vulcanised or thermoplastic – Determination of tear

strength – Part 1: Trouser, angle and crescent test pieces

This part of MS 1567 specifies three test methods for the

determination of the tear strength of vulcanised rubber, namely

29

MS 149 : 1992

Specification for new pneumatic passenger car tyres (First

revision).

This Malaysian Standard specifies definitions, designations testing

and minimum safety requirements for new pneumatic rubber tyres

for use on passenger cars.

Price RM20

MS 1097 : 2005

Rubber tread compound for hot (conventional) retreading of

passenger car and commercial vehicle tyres – Specification

(First revision)

This Malaysian Standard specifies the minimum requirements for

rubber tread compound for retreading of pneumatic tyres for use of

passenger cars and commercial vehicles.

Price RM10

MS 1208 : 2005

Precured tread for retreading tyres – Specification (First

revision)


procured tread for retreading tyres.

Price RM10

MS 1348 : 2005

Cushion gum used in procured retreading of tyres –

Specification (First revision)

This Malaysian Standard specifies the requirements for cushion gum

used in procured process of retreading tyres.

Price RM10

MS 1394 : 1996

Specification for new pneumatic tyres for highway vehicles

other than passenger cars.

This Malaysian Standard specifies requirements such as endurance,

strength, high speed performance and marking for pneumatic tyre

other than that of passenger car which is to use gazetted roads. It

also includes tyre for motorcycle.

Price RM20

MS 1439 : 1998

Definition of common terms used in the tyre industry-Pneumatic

tyres

This Malaysian Standard gives definition of common terms relating

to pneumatic tyres as used in the tyre industry.

Price RM20

MS ISO 4000-1 : 2002

Passenger car tyres and rims - Part 1 : Tyres (metric series)

This Malaysian Standard specifies the designation, dimensions and

load ratings of the metric series of tyres primarily intended for

passenger cars.

Price RM30

83.180 Adhesives

MS 562 : 1978 (2002)

Glossary of terms used in the adhesives industry.

Makes provisions for uniformity in the definitions of terms used in

the local adhesives industry and practice.

Price RM50

MS 876 : 1984

Specification for pressure sensitive polyvinyl chloride adhesive

tapes for electrical insulation.

Covers tapes with specific electrical properties for holding, binding

for insulating purposes. Requirements include working temperature,

appearance, colour, dimensions and range of physical and electrical

properties

Price RM30

MS 908 : 1984

Specification for synthetic resin adhesives (Phenolic and

aminoplastic) for plywood.

Describes technical requirements and test methods to determine

moisture content, pH value, mycological test and resistance to water

for adhesives with or without hardeners. Applies to all the three forms

of liquid, powder or film.

Price RM20

MS 1295 : 1992

Specification for adhesives for use with ceramic tiles and

mosaics.


adhesives used for fixing tiles to ensure that they are suitable for

their proposed application. The adhesives specifies in this Malaysian

Standard are classified into five types by their chemical composition

and physical form and into three classes based on their resistance

to water.

Price RM30

MS 1563 : 2002

Specification on adhesive for bonding decorative thermoset

laminates (contact adhesives)

This Malaysian Standard applies to sprayable adhesives and

brushable adhesives (including those for application by scraper)

intended for the bonding, on the contact bond principle, of decorative

thermoset laminated sheets to materials such as timber, metal, and

reconstituted boards.

Price RM30

MS 1810 : 2005

Test method for determining strength of adhesively bonded rigid

plastic lap-shear joints in shear by tension loading

This Malaysian Standard is intended to complement Test Method D

1002 and extend its application to single-lap shear adhesive joints of

rigid plastic adherends. The test method is useful for generating

comparative shear strength data for joints made from a number of

plastics. It can also provide a means by which several plastic surface

treatments can be compared.

Price RM40

MS ISO 13007-1 : 2005

Ceramic tiles - Grouts and adhesives – Part 1 : Terms, definitions

and specifications for adhesives

This standard is applicable to ceramic tile adhesives for internal and

external tile installations on walls and floors. This standard also

establishes the terminology, concerning the products, working

methods, application properties, etc. , for ceramic tile adhesives. It

also specifies the values of performance requirements for all ceramic

tile adhesives [cementitious (C), dispersion (D) and reaction resin ®

adhesives ]

Price RM20

30

Best Sellers

MS ISO 13007-2 : 2005

Ceramic tiles - Grouts and adhesives – Part 2 : Test methods

for adhesives

This standard specifies methods for determining characteristics for

adhesives used in the installation of ceramic tiles. The following test

methods are described :

- determination of open time (4.1), determination of slip (4.2),

determination of shear adhesion strength (4.3), determination of

tensile adhesion strength (4.4), determination of transverse

deformation (4.5), determination of chemical resistance (4.6)

Price RM50

MS ISO 15605 : 2003

Adhesives - Sampling

This Malaysian Standard specifies methods for sampling adhesives

and related products, in order to obtain uniform samples of convenient

size which are adequately representative of the product being

sampled.

Price RM20

83.200 Equipment for rubber and plastics

industries

_____________________________________________

MS ISO 13802 : 2004

Plastics – Verification of pendulum impact-testing machines –

Charpy, izod and tensile impact-testing

This standard specifies methods for the verification of pendulum

impact-testing machines used for the Charphy impact test, Izod impact

test and tensile test described in MS ISO 179-1, MS ISO 180 and

MS ISO 8256, respectively. The test machines covered by this

standard are of the pendulum type. The impact energy absorbed in

impating a test specimen is taken as being equal to the difference

between the potential energy of the pendulum and the energy

remaining in the pendulum after impacting the specimen. The impact

energy is corrected for friction and air-resistance losses.

Price RM50

31

Standards Number Price (RM) Page

NUMERICAL LISTING


MS 148 : Part 1 : 1973 30 29

MS 149 : 1992 20 30

MS 150 : 1999 10 28

MS 224 : 2005 20 28

MS 281 : Part 1 : 1999 10 1

MS 281 : Part 2 : 1998 10 1

MS 281 : Part 3 : 1998 10 1

MS 281 : Part 4 : 1999 10 1

MS 281 : Part 5 : 1998 10 1

MS 281 : Part 6 : 1998 10 1

MS 281 : Part 10 : 1999 10 1

MS 281 : Part 11 : 1999 10 1

MS 281 : Part 12 : 2001 10 1

MS 281 : Part 14 : 2001 20 1

MS 281 : Part 15 : 1992 10 2

MS 281 : Part 16 : 1999 10 2

MS 297 : 1981 10 2

MS 298 : 1985 50 2

MS 317 : 1986 10 2

MS 463 : 1994 20 3

MS 466 : 1987 20 2

MS 506 : 1977 (2004) 20 1

MS 511 : 1977 60 3

MS 562 : 1978 (2002) 50 30

MS 602 : 1979 30 22

MS 671 : Part 1 : 2002 20 3

MS 671 : Part 2 : 1992 20 20

MS 672 : 1999 40 19, 27

MS 676 : 2001 10 27

MS 679 : 1999 20 19, 27

MS 681 : 1980 30 22

MS 735 : 1996 20 27

MS 773 : 1999 30 19, 20,26,

MS 868 : 1999 20 20, 29

MS 876 : 1984 30 30

MS 908 : 1984 20 30

MS 973 : 2002 10 27

MS 974 : 2002 10 20

MS 976 : 2004 20 19

MS 978 : 1985 40 20, 25

MS 979 : Part 1 : 1985 40 20, 25

MS 979 : Part 2 : 1985 30 20, 25

MS 1010 : 1986 30 1,25

MS 1012 : 2003 20 16

MS 1013 : 1986 10 3 , 16

MS 1068 : 2002 10 27

MS 1070 : 2002 20 26

MS 1082 : 1994 20 20

MS 1097 : 2005 10 30

MS 1105 : 1988 20 22

MS 1106 : 1988 20 20

MS 1151 : 1989 10 22

MS 1151 : Part 1 : 2005 10 19

MS 1151 : Part 2 : 1992 20 22

MS 1155 : 2003 20 27

MS 1156 : 1989 20 20

MS 1157 : Part 16 : 1992 20 3

MS 1157 : Part 18 : 1992 10 4

MS 1157 : Part 19 : 1992 10 4

MS 1157 : Part 22 : 1991 10 4

MS 1157 : Part 24 : 1991 20 4

MS 1157 : Part 27 : 1993 30 4

MS 1157 : Part 29 : 1992 20 4

MS 1157 : Part 31 : 1992 20 4

MS 1157 : Part 34 : 1991 10 4

MS 1157 : Part 35 : 1991 20 4

MS 1157 : Part 38 : 2005 10 4, 18

MS 1157 : Part 39 : 1991 10 4

MS 1157 : Part 40/1 : 1999 20 5

MS 1157 : Part 40/2 : 1999 10 5

MS 1157 : Part 41 : 1999 20 2, 5

MS 1208 : 2005 10 30

MS 1225 : Part 1 : 2004 30 27

MS 1225 : Part 2 : 2006 30 27

MS 1267 : 1992 10 16

MS 1268 : 1992 10 21

MS 1269 : 1992 10 16

MS 1271 : 1992 10 9

MS 1272 : Part 1 : 1993 10 9

MS 1272 : Part 2 : 1992 20 9

MS 1274 : 1992 20 9

MS 1291 : 2003 20 27

MS 1292 : 1992 10 5

MS 1295 : 1992 30 30

MS 1303 : Part 1 : 1993 30 16

MS 1312 : 1993 10 21

MS 1332 : 1993 50 18

MS 1334 : 1993 20 16

MS 1336 : 1993 20 15

MS 1337 : 1993 20 19

MS 1339 : 1993 10 21

MS 1343 : Part 1 : 1993 10 16

MS 1343 : Part 2 : 1993 20 16

MS 1344 : 1993 20 21

MS 1345 : 1993 20 9, 15

MS 1348 : 2005 10 30

MS 1349 : 1994 20 9, 15

MS 1359 : Part 4 : 1994 10 2

MS 1359 : Part 5 : 1994 10 2

MS 1359 : Part 6 : 1994 10 2

MS 1359 : Part 7 : 1995 10 2

MS 1359 : Part 8 : 1995 10 2

MS 1371 : 1995 20 9, 16

MS 1385 : 1996 20 21

MS 1392 : 1998 10 2

MS 1394 : 1996 20 30

MS 1400 : 1996 20 21

MS 1405 : 1996 10 21

32


NUMERICAL LISTING


MS 1406 : 1996 20 9

MS 1407 : Part 1 : 1996 30 27

MS 1407 : Part 2 : 1996 30 27

MS 1407 : Part 3 : 2001 30 28

MS 1407 : Part 4 : 2001 20 28

MS 1418 : 1997 20 19

MS 1420 : 1997 10 23

MS 1421 : 2005 40 9

MS 1422 : 1997 10 23

MS 1423 : 1997 20 23

MS 1424 : 1997 10 21, 23

MS 1439 : 1998 20 30

MS 1440 : 1998 150 8

MS 1441 : 1998 10 9

MS 1442 : 1998 10 9

MS 1443 : 1998 10 29

MS 1444 : 1998 10 29

MS 1449 : Part 1 : 1999 20 5

MS 1449 : Part 3 : 1999 20 5

MS 1449 : Part 4 : 1999 20 5

MS 1449 : Part 5 : 1999 20 5

MS 1449 : Part 6 : 1999 20 5

MS 1465 : Part 1 : 1999 20 9

MS 1465 : Part 2 : 1999 20 10

MS 1466 : 1999 20 10

MS 1467 : 1999 10 10

MS 1468 : 1999 20 10

MS 1469 : 1999 10 10

MS 1470 : 1999 10 10

MS 1473 : 1999 10 10

MS 1476 : 1999 20 10

MS 1477 : 1999 20 23

MS 1478 : 1999 20 23,29

MS 1479 : 1999 20 23,29

MS 1501 : 2000 30 8

MS 1502 : 2000 30 28

MS 1504 : 2000 10 19

MS 1505 : 2005 40 23

MS 1509 : 2000 10 23

MS 1510 : 2000 20 28

MS 1521 : 2001 20 28

MS 1523 : 2001 10 5

MS 1524 : 2001 20 5

MS 1528 : Part 1 : 2001 30 18

MS 1530 : 2001 10 28

MS 1541 : 2002 10 2

MS 1542 : 2002 20 2

MS 1545 : 2002 10 26

MS 1546 : 2002 20 5

MS 1547 : 2002 10 5

MS 1548 : 2002 10 5

MS 1549 : 2002 10 3

MS 1550 : 2002 10 3

MS 1556 : 2002 20 21

MS 1557 : 2002 20 21

MS 1558 : 2002 10 21

MS 1559 : 2002 20 23

MS 1560 : 2002 20 21

MS 1563 : 2002 30 30

MS 1564 : Part 1 : 2003 30 28

MS 1564 : Part 2 : 2003 30 28

MS 1564 : Part 3 : 2002 30 28

MS 1564 : Part 4 : 2002 30 28

MS 1564 : Part 5 : 2002 20 28

MS 1564 : Part 6 : 2002 10 28

MS 1565 : 2002 20 29

MS 1566 : 2002 10 29

MS 1567 : Part 1 : 2002 20 29

MS 1568 : Part 7 : 2002 20 5

MS 1582 : 2003 20 21

MS 1593 : 2003 20 21

MS 1594 : 2003 20 22

MS 1733 : 2004 40 22

MS 1734 : 2004 20 22

MS 1735 : 2004 20 22

MS 1736 : Part 1 : 2004 20 25

MS 1736 : Part 2 : 2004 20 25

MS 1736 : Part 3 : 2004 20 25

MS 1736 : Part 5 : 2004 20 25

MS 1736 : Part 7 : 2004 50 25

MS 1737 : 2004 30 25

MS 1738 : 2004 10 25

MS 1739 : 2004 10 25

MS 1740 : 2004 10 26

MS 1741 : 2004 10 26

MS 1761 : 2004 10 26

MS 1769 : 2004 10 22

MS 1770 : 2004 20 22

MS 1771 : 2004 20 22

MS 1772 : Part 1 : 2004 20 23

MS 1772 : Part 2 : 2004 20 23

MS 1805 : 2005 40 23

MS 1806 : 2005 50 23

MS 1807 : 2005 40 23

MS 1808 : 2005 40 10

MS 1809 : 2005 40 18

MS 1810 : 2005 40 30

MS 1811 : 2005 50 19

MS 1812 : 2005 50 19

MS 1813 : 2005 40 16

MS 1856 : 2005 40 19

MS 1857 : 2005 40 20

MS 1858 : 2005 10 20

MS 1871 : 2005 20 18

MS 1872 : 2005 10 18

MS 1896 : 2005 40 24

MS 1897 : 2005 40 24

MS 1898 : 2005 40 24

MS 1899 : 2005 40 24

MS 2000 : 2005 50 24

MS 2001 : 2005 50 24

33


NUMERICAL LISTING


MS ISO 1209-2 : 1997 10 19

MS ISO 1210 : 1995 20 12

MS ISO/TR 1326 : 1995 10 12

MS ISO 1403 : 2002 10 26

MS ISO 1431-2 : 1999 20 7

MS ISO 1432 : 2000 10 7

MS ISO 1433 : 2000 20 7

MS ISO 1628-1 : 2004 30 12

MS ISO 1628-2 : 2004 20 12

MS ISO 1629 : 2004 10 29

MS ISO 1675 : 1995 10 13

MS ISO 1798 : 1998 10 13

MS ISO 1817 : 2002 30 7

MS ISO 1853 : 2002 20 7

MS ISO 1873 : Part 1 : 1994 10 17

MS ISO 1873 : Part 2 : 1994 10 17

MS ISO 1926 : 1997 10 19

MS ISO 2039-1 : 2004 20 13

MS ISO 2285 : 1999 10 7

MS ISO 2393 : 2000 20 7

MS ISO 2528 : 2000 20 24

MS ISO 2555 : 1995 20 13

MS ISO 2561 : 1998 10 17

MS ISO 2578 : 1995 30 13

MS ISO 2580 : Part 1 : 1994 10 17

MS ISO 2580 : Part 2 : 1999 20 17

MS ISO 2782 : 1999 20 7

MS ISO 2818 : 1995 20 13

MS ISO 2897-1 : 2001 10 17

MS ISO 2897-2 : 1999 20 17

MS ISO 2898-1 : 2001 10 17

MS ISO 2898-2 : 1999 20 17

MS ISO 2921 : 2001 10 7

MS ISO 3146 : 2004 20 13

MS ISO 3167 : 2003 20 13

MS ISO 3821 : 2002 20 26

MS ISO 3383 : 1998 10 7

MS ISO 3384 : 2002 20 7

MS ISO 3865 : 1999 20 7

MS ISO 4000-1 : 2002 30 30

MS ISO 4570-1 : 2002 10 29

MS ISO 4570-2 : 2002 10 29

MS ISO 4570-3 : 2002 20 29

MS ISO 4582 : 2001 30 13

MS ISO 4589-1 : 2000 20 13

MS ISO 4589-2 : 2000 30 17

MS ISO 4607 : 1995 20 13

MS ISO 4610 : 2004 20 18

MS ISO 4613-2 : 1999 10 18

MS ISO 4642 : 2004 10 27

MS ISO 4648 : 1998 10 7

MS ISO 4661-1 : 1998 10 8

MS ISO 4665 : 2002 20 8

MS ISO 4892-1 : 1998 20 13

MS ISO 4892-2 : 1998 20 13

MS ISO

MS ISO 34-2 : 1999 20 6

MS ISO 36 : 2002 10 3

MS ISO 37 : 1998 20 6

MS ISO 48 : 2002 30 6

MS ISO 60 : 2004 10 10

MS ISO 62 : 2001 20 10

MS ISO 75-1 : 1999 10 10

MS ISO 75-2 : 1999 10 10

MS ISO 75-3 : 1999 10 10

MS ISO 132 : 2002 20 6

MS ISO 175 : 2001 30 11

MS ISO 176 : 2001 10 11

MS ISO 177 : 2001 10 11

MS ISO 178 : 2004 30 11

MS ISO 179-1 : 2002 30 11

MS ISO 179-2 : 2002 30 11

MS ISO 180 : 2002 20 11

MS ISO 188 : 2001 20 6

MS ISO 247 : 2001 10 6

MS ISO 287 : 1999 10 6

MS ISO 289-1 : 1998 20 6

MS ISO 289-2 : 1998 10 6

MS ISO 291 : 2000 20 11

MS ISO 294-1 : 2002 30 16

MS ISO 294-2 : 2002 10 16

MS ISO 294-3 : 2002 20 16

MS ISO 294-5 : 2004 20 17

MS ISO 296 : 2001 10 3

MS ISO 305 : 2001 10 11, 8

MS ISO 489 : 1998 10 8, 11

MS ISO 498 : 2002 10 3

MS ISO 527 : Part 1 : 1994 20 11,17

MS ISO 527 : Part 2 : 1994 10 11,17

MS ISO 527 : Part 3 : 2001 10 24

MS ISO 527 : Part 4 : 2001 20 24

MS ISO 527 : Part 5 : 2001 20 24

MS ISO 604 : 2003 30 11

MS ISO 780 : 2001 20 6

MS ISO 813 : 1999 20 6

MS ISO 815 : 1998 20 6

MS ISO 844 : 1998 20 8, 12

MS ISO 868 : 2004 20 12

MS ISO 877 : 2001 30 8

MS ISO 899-1 : 1999 20 12

MS ISO 899-2 : 1999 20 12

MS ISO 974 : 2003 20 12

MS ISO 1043-1 : 2004 20 12

MS ISO 1043-2 : 2004 10 12

MS ISO 1043-3 : 2004 20 12

MS ISO 1043-4 : 2004 10 12

MS ISO 1158 : 2002 20 17

MS ISO 1183 : 1995 20 12

MS ISO 1209-1 : 1997 10 19

34

NUMERICAL LISTING


MS ISO 4892-3 : 1998 20 13

MS ISO 4892-4 : 1998 20 13

MS ISO 6252 : 1999 20 14

MS ISO 6427 : 1997 20 14,22

MS ISO 6471 : 2000 20 8

MS ISO 6502 : 2002 30 3

MS ISO 6603-1 : 2003 30 14

MS ISO 6603-2 : 2003 30 14

MS ISO 6762 : 2002 10 29

MS ISO 7111 : 1998 10 14

MS ISO 7391-1 : 2001 20 18

MS ISO 7391-2 : 1999 20 18

MS ISO 7619 : 2000 20 8

MS ISO 8013 : 2005 140 8

MS ISO 8256 : 1999 30 14

MS ISO 8570 : 2004 20 24

MS ISO 8789 : 2005 90 8

MS ISO 8985 : 2000 30 18

MS ISO 9026 : 1998 20 8

MS ISO 9413 : 2002 80 29

MS ISO 10508 : 2004 30 20

MS ISO 11346 : 1999 10 8

MS ISO 11357-1 : 1999 20 14

MS ISO 11357-2 : 2003 20 14

MS ISO 11357-3 : 2003 20 14

MS ISO 11357-5 : 2004 20 14

MS ISO 11357-6 : 2004 20 14

MS ISO 11357-7 : 2004 20 14

MS ISO 11424 : 2002 20 20

MS ISO 11425 : 2004 20 20

MS ISO 13007-1 : 2005 20 30

MS ISO 13007-2 : 2005 50 31

MS ISO 13468-1 : 2004 20 14

MS ISO 13468-2 : 2004 20 14

MS ISO 13586 : 2003 30 15

MS ISO 13802 : 2004 50 31

MS ISO 14782 : 2004 20 15

MS ISO 15512 : 2004 20 15

MS ISO 15605 : 2003 20 31

MS ISO 15850 : 2004 30 15

MS ISO 15876-1 : 2004 20 26

MS ISO 15876-2 : 2004 30 26

MS ISO 15876-3 : 2004 30 26

MS ISO 15876-5 : 2004 20 26

MS ISO 15876-7 : 2004 30 26

MS ISO 16014-1 : 2004 30 15

MS ISO 16014-2 : 2004 20 15

MS ISO 16014-3 : 2004 20 15

MS ISO 16014-4 : 2004 20 15

MS ISO 17281 : 2004 30 15

35

INDEX

Subject - MS Number - Page Subject - MS Number - Page

AAdhesives

- Bonding decorative thermoset laminates (MS 1563),30

- For ceramic tiles and mosaics (MS 1295),30

- Glossary (MS 562),30

- Phenolic & aminoplastic, for plywood (MS 908),30

- Pressure sensitive PVC, Electrical purpose (MS 876),30

- Sampling (MS ISO 15605),31

Ammonia, Anhydrous & aqueous (MS 506),1

Automotive lamps – Plastic lenses (MS 1469),10

BBearings

- Materials of elastomeric bridge bearings (MS 671:Pt.1),3

- Design & installation, Code of practice (MS 671:Pt.2),20

Buckets (Containers) – Plastics (MS 676),27

CCellular plastics

- Tensile properties (MS ISO 1926),19

- Bending test (MS ISO 1209-1),19

- Flexural properties (MS ISO 1209-2),19

- Rigid materials (MS ISO 844), 8, 12

Cold water storage

- Feed expansion cisterns (MS 1225:Pt. 1),27

- 600 gal capacity (MS 1225:Pt.2),27

Cushion Gum (MS 1348),30

Ceramic tiles

- Grouts and adhesives

- Terms and definitions (MS ISO 13007-1), 30

- Test methods

- Adhesives (MS ISO 13007-2),31

DDisposable polystyrene cutlery (MS 1502),28

FFeeding bottles (Babies) – Plastics (MS 735),27

Films (Materials) – PVC (MS 681),22

Film hardness, organic coating (MS 1509),23

Flexible cellular materials

- Slabs, bonded, molded urethane foams (MS 1332),18

- Flexible cellular materials (MS ISO 1798),13

- Flexible cellular materials (MS 1809),18

Flexible plastics laminates

- Determination of thickness (MS 1504),19

- Bond strength (MS 1505),23

Flexible packaging material

- Part 1 : Absolute methods (MS 1772:Pt.1),23

- Part 2 : Industrial methods (MS 1772:Pt.2),23

Floor mats - Rubber, For vehicles (MS 1068),27

G

Gas

- Chromatography - Residual vinyl chloride monomer

(MS 1013),3, 16

H

Hose

- Air and vacuum systems (MS ISO 11424),20

- Gas welding equipment (MS ISO 3821),26

L

Latex - Test methods (MS 466),2

M

Marine fenders - Rubber materials (MS 1385),21

Mattresses, Latex foam rubber

- For domestic & general use (MS 679),19, 27

Measuring equipment, domestic purposes

- Cup, spoon and litre measure (MS 1560),21

Mobile waste containers

- Part 1 : Two wheels, 80 L – 390 L (MS 1564:Part 1),28

- Part 2 : Four wheels, 500 L – 1200 L (MS 1564:Part 2),28

- Part 3 : Four wheels,

- 770 L – 1300 L, dome lids, trunnion and/or comb lifting

(MS 1564:Part 3),28

- Part 4 : Four wheels,

- 750 L – 1700 L, flat lids, Wide trunnion and/or BG

(MS 1564:Part 4),28

- Part 5 : test method and performance requirements

(MS 1564:Part 5),28

- Part 6 : safety and health requirement (MS 1564:Part 6),28

Motor vehicle

- PVC floor mat (MS 1470),10

- Rubber floor mat (MS 1068),27

Motorcycles

- Tyre dimensions and rims, Inch code (MS 1565),29

36

Index


N

Natural rubber latex concentrate

- Alkalinity (MS 281:Pt.4),1

- Boric acid content (MS 281:Pt.12),1

- Coagulum content (MS 281:Pt.6),1

- Centrifuged or creamed, ammonia-preserved types

(MS ISO 296),3

- Dry films (MS ISO 498),3

- Dry rubber content (MS 281:Pt.3),1

- KOH number (MS 281:Pt.11),1

- Mechanical stability (MS 281:Pt.5),1

- pH (MS 281:Pt.16),2

- Sampling (MS 281:Pt.1),1

- Total nitrogen (MS 281:Pt.14),1

- Total solid content (MS 281:Pt.2),1

- Viscosity (MS 281:Pt.15),2

- Volatile fatty acid number (MS 281:Pt.10),1

Natural rubber – Inner tubes for motor vehicles (MS 868),20, 29

Natural rubber products – Extractable proteins (MS 1392),2

O

Open-mouth sacks, polyolefin woven (MS 1521),28

P

Pacifiers (Babies) (MS 1156), 20

Packaging, Code of practice

- Pictorial marking (MS ISO 780),6

Paper, Method for the determination

- Moisture content determination (MS ISO 287),6

Pipe fittings

- Plastic waste pipe & fittings (MS 978),20, 25

- Unplasticised PVC sewerage pipe & fittings

(MS 979:Pt. 1),20, 25

- Unplasticised PVC, Underground sewerage pipe & fittings

(MS 979:Pt. 2),20, 25

Plastics

- Acrylonitrile/butadiene/styrene

- Designation (MS ISO 2580:Pt.1),17

- Preparation of test specimens (MS ISO 2580:Pt.2),17

- Adhesive bonds (MS 1810),30

- Amorphous thermoplastic

- Test specimens

- Bars (MS 1343:Pt.1),16

- Plates (MS 1343:Pt.2),16

- Average molecular mass

- General principles (MS ISO 16014-1),15

- Universal calibration method (MS ISO 16014-2),15

- Low-temperature method (MS ISO 16014-3),15

- High-temperature method (MS ISO 16014-4),15

- Barcol Hardness Impressor (MS 1808),10

- Beverage containers (MS 1476),10

- Bond strength (MS 1505),23

- Brittleness temperature (MS ISO 974),12

- Burning behavior by oxygen index (MS ISO 4589-1),13

- Burning behavior – Ambient – Temperature test

(MS ISO 4589-2),17

- Coding system (MS 1405),21

- Compressive properties (MS ISO 604),11

- Composite materials (MS 1812),19

- Short-beam strength (MS 1811),19

- Containers

- Packaging (MS 1733),22

- Blow-moulded thermoplastic (MS 1735),22

- Density & relative density of non-cellular plastics

(MS ISO 1183),12

- Deflection under load

- General test method (MS ISO 75-1),10

- Plastics and ebonite (MS ISO 75-2),10

- Determination of,

- Haze (MS ISO 14782),15

- Water content (MS ISO 15512),15

- Hardness

- Part 1 : Ball identification method

(MS ISO 2039-1),13

- Determination

- Burning behaviour of horizontal & vertical

(MS ISO 1210),12

- Flammability & burning rate (MS ISO/TR 1326),12

- Time temperature limits (MS ISO 2578),13

- Melting behaviour (MS ISO 3146),13

- Changes in colour & variations in properties

(MS ISO 4582),13

- Differential scanning calorimetry (MS ISO 11357-1),14

- Glass transition temperature

(MS ISO 11357-2),14

-Temperature and enthalpy of melting and

crystallization (MS ISO 11357-3),14

- Reaction-curve temperature and times

(MS ISO 11357-5),14

- Oxidation induction time (MS ISO 11357-6),14

- Crystallization kinetics (MS ISO 11357-7),14

- Ethylene, environmental stress (MS 1371),9, 16

- Ethylene/vinyl acetate (E/VAC)

- Preparation of test specimens & properties

(MS ISO 4613-2),18

- Ethylene/vinyl acetate copolymer (EVAC) thermoplastics

- Determination of vinyl acetate content

(MS ISO 8985),18

- Environmental stress cracking (MS ISO 6252),14

37

Index


- Non-instrumented (MS ISO 6603-1),14

- Instrumented (MS ISO 6603-2),14

- Puncture propagation (MS 1806),23

- Preparation of glass fibre reinforced (MS 1337),19

- Rigid cellular plastics materials (MS 1528:Pt.1),18

- Resins in liquid or emulsion or dispersions (MS ISO 2555),13

- Tensile-impact strength (MS ISO 8256),14

- Tensile creep (MS ISO 899-1),12

- Three point bending (MS 1473),10

- Transparent plastics

- Single-beam instrument (MS ISO 13468-1),14

- Double-beam instrument (MS ISO 13468-2),14

- Soluble matter

- General principles (MS ISO 1628-1),12

- Symbols

- Basic polymer (MS ISO 1043:Pt. 1),12

- Fillers and reinforcing materials (MS ISO 1043:Pt. 2),12

- Pasticizer (MS ISO 1043:Pt. 3),12

- Flame retardants (MS ISO 1043:Pt. 4),12

- Shrink tension (MS 1807),23

- Thermoplastics materials

- Compression moulding (MS 1334),16

- Injection moulding (MS ISO 294-1),16

- Small tensile bars (MS ISO 294-2),16

- Small plates (MS ISO 294-3),16

- Investigating anisotropy (MS ISO 294-5),17

- Thermosetting materials, Compression moulding

(MS 1336),15

- Tensile creep (MS 1345),9, 15

- Thermal stability, discoloration methods (MS ISO 305),11, 8

- Vinyl chloride homoplymers and copolymer

- Clorine content (MS ISO 1158),17

- WC seats (MS 976),19

Plastics container, specification

- Capacity, mass and tolerances or dimensions

(MS 1407:Pt. 2),27

- Screw thread (MS 1407:Pt. 1),27

- Container capacity, 5 L to 60 L (MS 1407:Pt.3),28

- Drums, 70 L - 250 L capacity (MS 1407:Pt.4),28

- Drainability (bottles and jars) (MS 1858),20

Plastics, Charpy impact properties

- Non-instrumented impact test (MS ISO 179-1),11

- Instrumented impact test (MS ISO 179-2),11

Plastics, Determination of tensile properties

- General principles (MS ISO 527:Pt. 1), 11, 17

- Test conditions for moulding and extrusion plastics

(MS ISO 527:Pt. 2), 11,17

Plastics – Flexible cellular materials (MS 1809),18

Plastics film

- Extraction by chemicals (MS 1805),23

- Puncture propagation (MS 1806),23

- Shrink tension (MS 1807),23

Plastics food containers, lids (MS 1558),21

- Film

- Parallel plate method (MS 1423),23

- Package yield (MS 1424),21, 23

- Film and sheeting

- Cold-crack temperature (MS ISO 8570),24

- Force required (MS 1151:Pt.2),22

- Tear resistance (MS 1151-1),19

- Mechanical scanning (MS 1339),21

- Wetting tension (MS 1420),23

- Test for haze (MS 1421),9

- Unrestrained linear thermal shrinkage (MS 1422),23

- Transmission of oxygen gas (MS 1734),22

- Fracture toughness (MS ISO 17281),15

- LEFM method (MS ISO 13586),15

- Tension fatigue crack (MS ISO 15850),15

- Flexural creep by three-point loading (MS ISO 899-2),12

- Glossary (MS 1440),8

- Flexural properties (MS ISO 178),11

- Shore (MS 1271),9

- Ball indentation (MS 1272:Pt.1),9

- Rockwell (MS 1272:Pt.2),9

- Gas transmission rate (MS 1344),21

- Guidelines for the standardization of methods-Viscosity

(MS ISO 1628/1),12

- Glass fibre reinforced (MS 1418),19

- Hardness

- Plasticized poly (vinyl chloride) PVC-P

- Designation systems & basis for specifications

(MS ISO 2898-1),17

- Preparation of test specimens & determination of

properties (MS ISO 2898-2),17

- Polycarbonate (PC) moulding

- Test specimens & determination of properties

(MS ISO 7391-2),18

- Designation system (MS ISO 7391-1),18

- High-strength thermosetting laminates (MS ISO 75-3),10

- Ignition loss of cured reinforced resins (MS 1813),16

- Impact-resistant polystyrene (PS-I)

- Designation systems & basis for specifications

(MS ISO 2897-1),17

- Preparation of test specimens & determination of

properties (MS ISO 2897-2),17

- Liquid resins-Density & relative density (MS ISO 1675),13

- Method of exposure to natural weathering

(MS ISO 4607),13

- Measuring shrinkage (MS 1501),8

- Multipurpose test (MS ISO 3167),13

- Matter extractable (MS ISO 6427),14, 22

- Open – Flame carbon-Arc lamps (MS ISO 4892-4),13

- Preparation of test specimens by machining

(MS ISO 2818),13

- Puncture impact, rigid plastics

38

Index


Plastics, Liquid chemicals

- Effects of immersion (MS ISO 175),11

Plastics, Laboratory light sources

- General guidance (MS ISO 4892-1),13

- Xenon-arc sources (MS ISO 4892-2),13

- Fluorescent UV lamps (MS ISO 4892-3),13

- Open – Flame carbon - arc lamps (MS ISO 4892-4),13

Plastics washing basins, domestic use (MS 1530),28

Plastics lockable containers, household wares (MS 1557),21

Plastics, Plasticizers

- Activated carbon method, loss (MS ISO 176),11

- Determination of migration (MS ISO 177),11

Plastics, Tensile properties

- Films and sheets (MS ISO 527-3),24

- Isotropic and orthotropic fiber-reinforced composites

(MS ISO 527-4),24

- Undirectional fibre-reinforced composites

(MS ISO 527-5),24

Plastic lenses – Automotive lamps (MS 1469),10

Plastics resistivity- Volume (MS 1465:Pt 2),10

- Surface (MS 1465:Pt 1),9

Plastics moulding - Code of practice for system of tolerances for

dimension (MS 1406),9

Plastic, Method of test

- Abrasion resistance (MS 1897),24

- Changes in colour & appearance (MS ISO 4582),13

- Determination of flexural properties of rigid plastics

(MS 1349), 9, 15

- Environmental stress crack (MS 1593),21

- Exposure to solar radiation (MS ISO 877),8

- Hot seal strength (MS 1899),24

- Izod impact strength (MS ISO 180),11

- Load containment (MS 1896),24

- Peel cling (MS 2001),24

- Protrusion puncture (MS 1898),24

- Standard atmospheres (MS ISO 291),11

- Temperature of deflection under load (MS 1274),9

- Water vapor transmission rate (MS 2000),24

Plastics piping system, hot and cold water

- Polybutylene

- Fittings (MS ISO 15876-3),26

- Fitness for purpose of the system

(MS ISO 15876-5),26

- General (MS ISO 15876-1),26

- Guidance for the assessment of conformity

(MS ISO 15876-7),26

- Pipes (MS ISO 15876-2),26

Crosslinked polyethylene (PE-X)

- General (MS 1736:Part 1),25

- Pipes (MS 1736:Part 2),25

- Fittings (MS 1736:Part 3),25

- Fitness for purpose of the system

(MS 1736:Part 5),25

- Guidance for the assessment of conformity

(MS 1736:Part 7),25

- Thermoplastic pipes, installation (MS 1737),25

- Thermoplastics pipes, temperature cycling

(MS 1739),25

Plastics, polyethylene tank

- Cold water storage (MS 1225:Part 1),27

Plastic piping system

- Tubular test pieces (MS 1738),25

- Test method for leaktightness (MS 1740),26

Plastics tableware (MS 1556),21

Plastics, water absorption (MS ISO 62),10

Pneumatic passengers car tyres (MS 149),30

Pneumatic tyres (MS 148:Pt. 1),29

- Retreads, For motor vehicles (MS 224),28

- Pneumatic tyres (MS 1439),30

Polyethylene

- Carbon black dispersion (MS 1442),9

Polyethylene container

- Environmental stress-crack- blow-moulded (MS 1582),21

Polyethylene film – Low density (MS 1478),23, 29

Polyethylene Sheeting-Construction, industrial & agricultural

applications (MS 1479),23, 29

Polyethylene film

- Determination of 2% secant modulus (MS 1467),10

- Free falling dart method (MS 1105),22

Polyethylene Film & Sheeting (MS 1477),23

Polyethylene tanks – 600 gal (MS 1225:Pt.2),27

Polyethylene terephthalate (PET) bottles

- 24-hour gas (air) space acetaldehyde content

(MS 1468),10

Polypropylene and propylene - copolymer thermoplastics

- Designation (MS ISO 1873:Pt. 1),17

- Preparation of test specimens (MS ISO 1873:Pt. 2),17

Polymers - Cable insulation & sheaths, Test methods

- Thermogravimetric measurements (MS ISO 7111),14

Polymeric materials

- Compression set (MS 1871), 18

- Humid conditions (MS 1872), 18

Polystrene – Residual styrene monometer (MS ISO 2561),17

Polystyrene cushioning foams (MS 1510),28

Polyurethane foam, high-resilience (MS 1268),21

Precured tread (MS 1208),30

PVC

- Film (MS 681),22

- Rigid PVC (MS 1010),1, 25

- Resin (MS 1012),16

- Floor mats – motor vehicles (MS 1470),10

R

Radiator hose - Rubber, For automobile (MS 1070),26

Raw rubber – Green strength (MS ISO 9026),8

39

Index


Raw natural rubber, test methods for technically specified

- Colour (MS 1359:Pt. 5),2

- Dirt content (MS 1542),2

- Mooney viscosity (MS 1359:Pt. 4),2

- Rapid plasticity and plasticity retention (MS 1359:Pt. 6),2

- Volatile matter (MS 1548),5

- Mooney Accelerated Storage Hardening (MASHT)

(MS 1359:Pt. 7),2

- Wallace Accelerated Storage Hardening (WASHT)

(MS 1359:Pt. 8),2

Residual vinyl chloride monomer (MS 1013 ),3,16

Retread tyres - Pneumatic, For motor vehicles (MS 224),28

Rubber

- Achieving elevated or subnormal temperature

(MS ISO 3383),7

- Atomic absorption spectrometry

- Copper content (MS 1449:Pt 3),5

- Iron content (MS 1449:Pt 5),5

- Zinc content (MS 1449:Pt 1),5

- Method-Manganese content (MS 1449:Pt 4),5

- Magnesium content (MS 1449:Pt 6),5

- Metal content

- Determination of calcium content

(MS 1568:Pt.7),5

- Bands (MS 973),27

- Curemeters (MS ISO 6502),3

- Crystallization (MS 1546),5

- Determination of ash (MS ISO 247),6

- Elastomeric teats (MS 1082),20

- Flexible tubing & hose, For LPG installation

(MS 773),19, 20, 26

- Gloves

- For medical examination & diagnostic (MS 1155),27

- Surgical (MS 1291),27

- Residual powder

- Power free (MS 1549),3

- Powdered rubber (MS 1550),3

- Hoses - Radiator, for automobiles (MS 1070),26

- Measurement of resistivity (MS ISO 1853),7

- Raw natural (MS 297),2

- Raw natural, Sampling (MS 298),2

- Rubber teat-Volatile nitrosamines (MS 1312),21

- Rubber thread - For retreating automobile tyre

(MS 1097),30

- Rubber seals – Water supply, drainage & sewerage

pipelines (MS 672),19, 27

- Rubber, vulcanized, methods of test (MS ISO 3865),7

- Resistance to weathering (MS ISO 4665),8

- Seeds, for commercial planting (MS 463),3

- Seals-water stops, materials (MS 1292),5

- Solvent extract (MS 1524),5

- Swimming fins (MS 974),20

- Physical tests (MS ISO 4661-1),8

40

- Test methods (MS ISO 3383),7

- Hardness test (MS ISO 815),6

- Pocket hardness meters (MS ISO 7619),8

- Vulcanized, thermoplastic, ageing and heat resistance

(MS ISO 188),6

- Vulcanized, temperature-retraction characteristics

(MS ISO 2921),7

Rubber hose

- Agricultural spraying (MS 1545),26

- Non-collapsible (MS ISO 4642),27

Rubber hoses and hose assemblies

- Automotive power-steering systems (MS ISO

11425),20

Rubber latices

- Natural, Evaporated preserved (MS 317),2

- Nomenclature (MS ISO 1629),29

Rubber latex concentrate

- Alkalinity (MS 281:Pt.4),1

- Boric acid content (MS 281:Pt.12),2

- Coagulum content (MS 281:Pt.6),1

- Dry rubber content (MS 281:Pt.3),1

- KOH number (MS 281:Pt.11),2

- Mechanical stability (MS 281:Pt.5),1

- pH (MS 281:Pt.16),2

- Sampling (MS 281:Pt.1),1

- Sludge content (MS 1541),2

- Total solid content (MS 281:Pt.2),1

- Temperatures of 5 – 40 degrees celcius (MS 1547),5

- Total nitrogen content (MS 281:Pt.14),1

- Volatile fatty acid number (MS 281:Pt.10),1

- Viscosity (MS 281:Pt.15),2

Rubber test mixes – Equipment & procedures

(MS ISO 2393),7

Rubber threads - Test methods (MS 1400),21

Rubber tread, Compund (MS 1097),30

Rubber tyre – Determination of tyre plunger energy (MS

1444),29

Rubber, Unvulcanized

- Mooney viscosity (MS ISO 289-1),6

- Pre-vulcanization characteristics (MS ISO 289-2),6

S

Sacks - Polyethylene, Heavy-duty (MS 1106),20

Safety

Seal, Strength – Flexible barrier (MS 1441),9

Sealing rings - Rubber, For water supply & drainage pipeline

(Withdrawn) (MS 672),19, 27

Seasonings see also Condiments

Seeds

- Rubber, For commercial planting (MS 463),3

- Determination of tear strength

- Trouser, angle and crescent test pieces

(MS 1567:Pt.1),29

- Small (delft) test pieces (MS ISO 34-2),6

- Estimation of life-time & maximum temperature

(MS ISO 11346),8

- Low temperature stiffening (Gehman test)

(MS ISO 1432),7

- Measurements (MS ISO 4648),7

- Tensile stress – Strain properties (MS ISO 37),6

- Temperature rise (MS 1157:Pt 41),2, 5

- Textile fabrics (MS ISO 36),3

- Methods of test

- Preferred gradations of properties (MS ISO 1433),7

- Staining in contact with organic material

(MS ISO 3865),7

- Preparation of samples

- Physical tests (MS ISO 4661-1),8

- Chemical test (MS 1157:Pt.39),4

- Time-interval (MS 1523),5

- Abrasion resistance

- Rotating cylindrical drum device (MS 1157:Pt 40/1),5

- Abrasive wheel (MS 1157:Pt 40/2),5

- Adhesion to

- Rigid plates (MS 1157: Pt. 19),4

- Wire cord (MS 1157: Pt. 31),4

- Metal two-plate (MS 1157: Pt. 38),4, 18

- Rigid substrate – 90 degrees peel method

(MS ISO 813),6

- Ageing characteristics (MS 1157:Pt. 34),4

- Hardness (MS ISO 48),6

- Tension set (MS ISO 2285),7

- Accelerated ageing

- Flex cracking (MS ISO 132),6

- Permeability (MS ISO 2782),7

- Resistance to ozone cracking (MS 1157:Pt.16),3

- Indentation hardness (MS ISO 7619),8

- Modulus in shear (MS 1157:Pt.18),4

- Effect of liquids (MS ISO 1817),7

- Density (MS 1157:Pt.22),4

- Antistatic & conductive products (MS 1157:Pt.24),4

- Rebound resilience (MS 1157:Pt.27),4

- Static adhesion (MS 1157:Pt.29),4

- Compressed stress relaxation (MS ISO 3384),7

- Tension fatigue (MS 1157:Pt.35),4

W

Water tanks - 600 gal (MS 1225:Pt.2),27

ZZinc oxide - For use in rubber (MS 511),3

Index


Sheet materials

- PVC, Thick (MS 602),22

- Water vapour transmission rate, Gravimetric method

(MS ISO 2528),24

Solid materials – Determination of linear thermal expansion

(MS 1466),10

Surgical rubber gloves, single use (MS 1291),27

T

Tear tests

- Plastic films & sheetings (MS 1151-2),22

- Tear resistance (MS 1151-1),19

Test method

- Plastics tighted drums (MS 1856),19

- Threaded plastics closures (MS 1857),20

Textile-reinforced rubber water hose (MS ISO 1403),26

Thermoplastic containers

- Blown, column crush properties (MS 1594),22

- Packaged reagents / proprietary products (MS 1559),23

Thermoplastics pipes

- Hot and cold water systems (MS ISO 10508),20

Thermoplastics rubber

- Tensile stress-strain properties (MS ISO 37),6

Thermoplastic road marking materials (MS 1303: Pt. 1),16

Thermoplastic, Method of test for plastics

- Melt flow index (MS 1267),16

- Vicat softening temperature (MS 1269),16

Transparent Plastics – Refractive Index (MS ISO 489),8, 11

Tubes (Tyres) - Inner tubes for motor vehicles (MS 868),20, 29

Tyres (MS 149),30

- Pneumatic, Retread, For motor vehicles (MS 224),28

- Pneumatic, for highway vehicles (MS 1394),30

- Passenger car and rims (MS ISO 4000-1),30

- Tubeless, Test methods (MS 150),28

- Solid tyres (MS 1566),29

- Valves

- ISO core chamber No.2 (MS ISO 6762),29

- Dimension and designation (MS ISO 9413),29

- Valve threads

- 5V1, 5V2, 6V1 and 8V1 (MS ISO 4570-1),29

- 9V1, 10V1, 12V1 and 13V1 (MS ISO 4570-2),29

- 8V2, 10V1, 11V1, 13V2, 15V1, 16V1, 17V1, 17V2,

17V3, 19V1, 20V1 (MS ISO 4570-3),29

V

Vulcanized rubber

- Creep tests (MS ISO 8013), 8

- Crystallization effect under compression (MS ISO 6471),8

- Dynamic strain test (MS ISO 1431-2),7

41

ORDER FORM

The Malaysian Standards listed in this catalogue can be purchased from SIRIM Berhad, Technical Information

and Intellectual Property Services Department and can be ordered by mail, fax or e-mail.

For ordering purposes, please use the order form below.

Name : ____________________________________________

Company Name : _________________________________________

Address & Tel / Fax / E-mail : ________________________________

________________________________________________________

Malaysian Standards Number (MS No.) Unit Price* Quantity Cost (RM)

TOTAL

Postage & Handling Charges ( 10% of total or RM5.00 whichever is more )

GRAND TOTAL

* For oversea order, please contact SIRIM Berhad for prices.

Enclosed is a cheque no. ___________________ dated __________________ amounting

RM ____________ for the above order. ( Cheque is to be made payable to SIRIM Berhad )

____________________________ ___________________

Signed & Company Stamp Date

Send to : SIRIM Berhad, Technical Information & Intellectual Property Services Department,

1, Persiaran Dato’ Menteri, Section 2, 40000 Shah Alam, MALAYSIA

Tel : ++6 03 - 5544 6118 / 6105 / 6112; Fax : ++ 6 03 - 5544 6114 / 5544 6146

E-mail : [email protected]

Attention : Manager

Documents

11-Rubber & Plastics