– 1 – – 2 –

– 3 – – 4 –

1. Introduction

1.1 Package ContentsThank you for purchasing our POE-152 IEEE 802.3af Power over Ethernet Injector, your Power over Ethernet Injector package shall contains following contents:

Check the contents of your package for following parts:

• PoweroverEthernetInjectorx1

• User'sManualx1

• PowerAdapterx1

If any of these pieces are missing or damaged, pleasecontact your dealer immediately, if possible, retain thecartonincludingtheoriginalpackingmaterial,andusethemagainst to repack the product in case there is a need toreturn it to us for repair.

1.2 Key Features• Comply with IEEE 802.3af Power over Ethernet, IEEE802.3/802.3u10/100Base-TX/802.3ab1000Base-T

• Provide DC 48V power over RJ-45 Ethernet cable todevicewithEthernetport

• Auto-detect of PoE IEEE 802.3af equipment, protectdevicesfrombeingdamagedbyincorrectinstallation

• WorkwithEIA568,category5,4-paircablesfor10Base-Tor100Base-TXand1000Base-T

1.4 Product Outlook

48V

DC

Ethe

rnet

Power over Ethernet InjectorIEEE 802.3af

PoE

PWR

Ethernet+D

C

PoE-IEEE 802.3afReadyPow

er in-use

LED definition:

LED Color Function

Power YellowLightstoindicatethatthePOE-152has power.

PoEready/in-use

GreenLightstoindicatetheportisproviding48VDCin-linepower.

1.3 SpecificationModel POE-152

Ethernet Connector

2xRJ-45(1fordata+DCin,1forDataout)

EthernetDataRate10/100/1000Mbps(varyonEthernetdeviceattached)

InputVoltage DC48V,0.4A

Numberofdevicecanbepowered

1

EthernetCable TIA/EIA-568,Category5/5e/6cable

LEDIndicator 1xpower,1xPoEready/in-use

Dimension(WxDxH)

73x55x24mm

EMI FCC Class B, CE mark

StandardCompliance

IEEE 802.3 EthernetIEEE 802.3u Fast EthernetIEEE802.3abGigabitEthernetIEEE 802.3af Power over Ethernet (PSE)

RJ-45PowerInsertion Pair

Pair1,2,3,6(End-Span)

2. Hardware Installation

This product provides three different running speeds –10Mbps, 100Mbps and 1000Mbps in the same deviceand automatically distinguishes the speed of incomingconnection.

This section describes the hardware features of POE-152.BeforeconnectinganynetworkdevicetothePOE-152,readthis chapter carefully.

2.1 Before InstallationBefore your installation, it is recommended to check yournetwork environment. If there is any IEEE 802.3af devicesneed to power on, the POE-152 can provide you a wayto supply power for this Ethernet device conveniently andeasily. The POE-152 equips with an AC-DC adapter withDC48V inputand injects thisDCpower into thepinof thetwistedpaircable(pair1,2andpair3,6).

If there is very difficult to find a power socket for AC-DCAdapter of your non IEEE 802.3af networked device, thePOE-152 and POE-152S can provide you a way to supplyDCpowerforthisEthernetdeviceconvenientlyandeasily.

Note

The POE-152 and POE-152S can be installedinpair.However, theuseof third-partydeviceis allowed if the device complied with IEEE802.3afstandard.

– 5 – – 6 –

2.2 POE-152, the Injector Installation1.Connect a standard network cable from Switch/worksta-

tion to “Ethernet” port of POE-152.

2.Connect the long cable that will be used to connect totheremotedevicetotheport“Ethernet + DC”.

3.Connect the AC adapter to “DC 48V” of POE-152. The powerLEDwillbesteadyon.

4.Connect with IEEE 802.3af devices, due to the capa-bilityof IEEE802.3afstandard, thePOE-152candirectlyconnect with any IEEE 802.3af end-nodes like wirelessaccess point, VoIP phones and Internet camera wheresupport IEEE 802.3af In-line Power over Ethernet port. The screen in Figure 1 appears.

Switch

100 meters

PoE

PowerData

PoE IP CameraPOE-152Power

Data

AC

Figure 1: Connection to IEEE 802.3af Device

Once POE-152 detects the existence of an IEEE 802.3afdevice, the LED indicatorwill be steady, ON to shows it isprovidingpower.

Note

If the connecteddevice is not fully complyingwith IEEE 802.3af standard or in-line powerdevice, the LED indicator of POE-152 will notbesteadyon.

2.3 POE-152 and POE-152S, the IEEE 802.3af Injector and Splitter Installation

1.Connect a standardnetwork cable from“Ethernet+DC” of POE-152 to “Ethernet+DC” of POE-152S. The POE LEDofPOE-152/POE-152Swilllightoncontinuance.

2.Connect the UTP cable in the package from “Ethernet” ofPOE-152StotheRJ-45portofremotedevice.

3.ConnectproperDCplugfrom“DC OUT” of POE-152S to remotedevice.

4.Power on the remote device and the LED indicator onPOE-152S will remains on.

Wireless APPOE-152 POE-152S

Gigabit Switch

100 meters

Figure 2: Connection Architecture over POE-152/152S

Note

1. According to IEEE 802.3af standard, thePOE-152will not inject power to the cableifnotconnectingtoIEEE802.3afdevices.

2. Please ensure the POE-152S output voltage is correctbeforeapplyingpower to remotedevice.