Upload
others
View
6
Download
0
Embed Size (px)
Citation preview
1. Camera Sensor Specifications Interface : UBS 2.0 / USB 3.0 / UTP
INPUT : DC24V 6.5A running resolution : 320 x 320 400 FPS Camera : 2 ea IR light : 1 set area : Driver, iron, putter, rough, bunker *Area analysis area: - left and right 35 degrees, upper and lower 0 to 80 degrees - Analysis within 60cm of the ball forward *Sphere analysis speed range: 0.8 to 150 m / s *Response speed after analyzing the ball: - Less than 3 m / s 0.6 sec - 3 m / s or more 0.2 sec Support simultaneous left and right Working Temperature: -5°C ~ 45°C Storage Temperature: -20°C ~ 60°C Working Relative Humidity: 20% ~ 80% Storage Relative Humidity: 20% ~ 95% 2. Recommended PC Specifications
CPU : More than, intel i5 RAM : More than ,4 Gb Main board : gigabyte H-97 Gaming or AAeon IMBM-Q87A-A10-MS VGA : More than , nvidia gforce 560 GTX Power : More than, 500W OS : Windos 7 32Bit
3. Sensor installation location
1000
2800 ~ 3000
1000
Tee
Tee
3. Camera installation
Be sure to connect to the USB 3.0 terminal on the back of the PC. Power Off in Power Management of CMOS Setup of Main Board The USB power supply must be disabled. (The camera may be adversely affected.) Item names may vary from manufacturer to manufacturer.
In the "Driver_PARONCAMUSB3" folder, specify the driver according to the Window 7 specification and install it. x64 : Windows 7 64 bit X86 : Windows 7 32 bit
"Driver_PARONCAMUSB3" and "ParOnGolfV3" in a random folder on the PC. Copy it.
4. Driver Installation
Once installed, it is registered in Device Manager as follows:
Windows settings must be as follows:
Windows settings must be as follows:
You must disable the sleep power settings for each Root Hub and Hub as follows:
Run ParOnGolfV3.exe from the "ParOnGolfV3" folder.
Click ParOnGolfV3 at the bottom of the Windows desktop.
5. ParOnGolfV3 실행
Enter your password. . At first run, if you enter any letter or number, Is set. (This password is stored in pass.txt in the "ParOnGolfV3" folder. You can change the contents of this file when changing the password. If you do not enter it within 20 seconds, it disappears to the bottom of the screen.
The following screen appears.
If it is not a normal connection, a message like the following appears in the status window. The Internet must be connected and authenticated before normal operation.
Check camera (1) line / usb (-1): Camera 1 is not connected. Check camera (2) line / usb (-1): Camera 2 is not connected
If the above FPS is 390, you need to install the latest USB driver from the PC motherboard manufacturer site. If it does not work, the CPU is not Intel i5 or above, or the specification of the motherboard should not be low. The motherboard must be replaced according to the recommended specifications.
Place the ball on the tee with 30cm on both sides, about 60cm on the front, and 30cm on the back as shown. At this time, the matte color where the ball is placed should be dark and uniform.
Press "check light". (Above and below)
6. Set brightness of image
Use the keyboard to set the number of BRIGHTNESS to 290 and then press apply There are four yellow circles and six blue circles on the screen. Remove or add four balls. Press one of the yellow circles to turn red. Click on the center of the ball and the yellow circle will move to the ball. Adjust to wrap the ball completely. Place all 4 yellow circles on the ball. The blue circles are evenly spaced. (If you press the circle to move, it turns red.
Press check light (ball / mat) to set the brightness automatically (about 10 seconds). When the completion message appears in the Sensor info field, click Apply. (The camera above and below are all the same way.) The number below the threshold must be at least 60 and the number of empty spaces must be zero. If the colors of the mat and carpet are not uniform, automatic adjustment may not be possible. In this case, adjust the number of BRIGHTNESS with the keyboard and press apply. (The camera above and below are all the same way.)
Click "view popup".
Only the area used by the camera is displayed. Place the ball in all places, place the yellow circle on the ball, and place the blue circle in the empty space. The empty space (blue circle) must have a value of "0" The ball (yellow circle) increases the Brightness value so that the value is above 60. The empty space (blue circle) has a value of "0" (if it is greater than or equal to 0, the brightness value must be lowered). The balls (yellow circles) can be over 60 in value (rather more stable, 70-80)
Click "view popup".
Only the area used by the camera is displayed. Place the ball in all places, place the yellow circle on the ball, and place the blue circle in the empty space. The empty space (blue circle) must have a value of "0" The ball (yellow circle) increases the Brightness value so that the value is above 60. The empty space (blue circle) has a value of "0" (if it is greater than or equal to 0, the brightness value must be lowered). The balls (yellow circles) can be over 60 in value (rather more stable, 70-80)
Click “Ball direction ". (Above and below)
7. Set direction and position for ball analysis
Place the + shape jig on the tee in the direction of the target. (To set the direction and trajectory of the ball. If the straight line is not correct, the direction and trajectory of the ball will change.)
Use Top, Bottom, Left, Right to center the + character on the screen and press save.
Top, bottom, left, right Click on the circle and click on each end of the + After making the following, click save. Even if you take a rough white spot, it will automatically settle.
8. 볼 영역 설정
Click Club area. (Above and below) Drag the mouse to set the Driver, Iron, Putter, Rough, and Bunker areas. When you create, extend, or reduce the size, drag and adjust the mouse When you move the mouse, move it to the desired position. Press apply for each zone setting. After setting the bunker at the end, be sure to remove all balls from the mat Do not appear on the screen and press apply. (Important)
9. Pitch adjustment
① Adjust the speed of the D / I driver and the wood irons to%. P Adjust the speed of putting to%. Used for distance adjustment. ② Adjust the rising angle. When you raise 1, 2, 3, lower, -1, -2, -3, ... .. ③ Adjust the left and right angles. 1, 2, 3 when sending to the right, -1, -2, -3, ... ④ X% Adjust the side spin value to%. + The side spin value is arbitrarily +, -. Use when the ratio of hook to slice is different. ⑤ Adjust the back spin value to%. After adjusting, press apply.
①
②
③
④
⑤