06 20R300 1 C200 Hardware Configuration

1April 19, 2023

Describe the Configuration of C200 Hardware and I/O

C200 Hardware Configuration Describe the Configuration of C200 Hardware and I/O C200 Hardware Configuration Describe the Configuration of C200 Hardware and I/O

EXP20R300 - EPKS CEE C200/C300/ACE

Honeywell

2

April 19, 2023

Introduction

• In this lesson you will learn to configure C200 hardware and I/O using Control Builder

• At the conclusion of this lesson, you will be able to:

– Identify C200 hardware, slot numbers and addressing

– Configure and download hardware configurations for these components

C200 Hardware Configuration Describe the Configuration of C200 Hardware and I/O


Honeywell

3

April 19, 2023

Topics

• Hardware and Slot Numbers

• Configuring the FTEB, Controller, and CEE

• Configuring IOMs

• Loading the Controller, CEE, and IOMs

• Activating a CEE



Honeywell

4

April 19, 2023

C200 Chassis Hardware

• Below is an example C200 chassis configured with:

Control Processor (C200)

123

4

5678

5 6 7 8432

1

10-slot chassis

Power supply

ControlNet Interface (CNI)or FTE Bridge

IO Link Interface Module

Fieldbus Interface Module

Redundancy Module

CNI to Remote I/O



Honeywell

5

April 19, 2023

C200 I/O Slot Numbers

• To determine the slot location of C200 related hardware you must:

– Start counting at zero (do not count the power supply)

– Count from left to right

– Count both spaces if the module occupies two spaces

Power Supply 12

34

56

78

0

9



Honeywell

6

April 19, 2023

Topics








Honeywell

7

April 19, 2023

Fault Tolerant Ethernet Bridge (FTEB)

• Single-wide chassis module

• Connects to FTE cable A and B

• Supports chassis redundancy

• Can only be used for Supervisory Control Network connection

• ControlNet and downlink CNIs required for all I/O communications including peer-to-peer to AB devices

• Rotary switch for FTE Node Number (1 to 99)

– IP address of FTEB can be set to higher than 99 by configuring the Base IP address accordingly from System Preferences option



Honeywell

8

April 19, 2023

Fault Tolerant Ethernet Bridge (FTEB), contd.

• The FTEB can be used for FIM-only connections to the supervisory network

• In the Project and Monitoring tabs in Control Builder you will see the FTEB as the root for the CPM

• You will set up the FTEB using IP addresses

• An FTE community can only have 99 FTEBs so you are limited to 49 redundant pairs and 99 single FTEBs in one community

• The FTE connection to the FTEB is 10Mbps

– 10Mbps is only supported in FTE for connection from an FTEB to a switch and nowhere else



Honeywell

9

April 19, 2023

Configuring a FTEB

Must match the hardware switches found on top of the

FTEB card



Honeywell

10

April 19, 2023

Question 1: FTEB Node Numbering

No. '257' is not a valid FTEB node number. FTEB IP address can be set to higher then 99

by configuring the base IP address accordingly in System Preferences in Control Builder.

Click anywhere to continue.






















Correct - Click anywhere to continueCorrect - Click anywhere to continueIncorrect - Click anywhere to continueIncorrect - Click anywhere to continueYou answered this correctly!You answered this correctly!

Your answer:Your answer:The correct answer is:The correct answer is:

You did not answer this question completelyYou did not answer this question completelyYou must answer the question before continuing

You must answer the question before continuing

Submit Clear

Which of the following is not a valid FTEB node number?

A) 110

B) 99

C) 257

D) 1



Honeywell

11

April 19, 2023

Configuring a Controller

Follow these steps to add a new control processor module (CPM) from the pull-down menus



Honeywell

12

April 19, 2023

Configuring a Controller – CPM Main Tab

• Data entry details will be provided in the lab exercise

MAC ID of CNI Card

connected to server

CNI slot #

Slot number of CPM

Check for the redundant controller and then enter its

name

ControlNet or Ethernet driver

Tag Name & Item Name

Driver Name

Alarm reporting by CEE



Honeywell

13

April 19, 2023

Configuring a Controller – CPM Main Tab, contd.

• Data entry details will be provided in the lab exercise Ethernet

NetworkDriver Name

Slot Number of CPM

Redundant Controller & Name



Honeywell

14

April 19, 2023

• History parameters and control level required to operate this CPM

Configuring a Controller – Server History Tab



Honeywell

15

April 19, 2023

Configuring a Controller – Group and Trend Assignment

Point, group, trend and associated displays (that reside on the

server) are defined on the Server Displays tab

Select OK to close and save the new

controller



Honeywell

16

April 19, 2023

Question 2: Supervisory MAC Address for a CPM

Incorrect. The Supervisory MAC address is the MAC address of the CNI card connected to the server.












Correct! The Supervisory MAC address is the MAC address of the CNI card connected to the server.


Correct! The Supervisory MAC address is the MAC address of the CNI card connected to the server.






Submit Clear

While configuring a ControlNet connected control processor module (CPM) in Control Builder, which MAC address is entered as the Supervisory MAC address?

A) The device index of FTEB card

B) The MAC address of the PCIC card

C) The MAC address of CNI card connected to the I/O rack

D) The MAC address of CNI card connected to server



Honeywell

17

April 19, 2023

Configuring a CEE – CPM/CEE Tree View

Double-click to open the configuration form

Click the + sign to expand the CPM in the

Project tab



Honeywell

18

April 19, 2023

Configuring a CEE – Main Tab

Data entry details will be provided in the Lab exercise



Honeywell

19

April 19, 2023

Configuring C200 Hardware

• The Control Processor Module (CPM) and its Control Execution Environment (CEE) are configured but not yet downloaded



Honeywell

20

April 19, 2023






Topics



Honeywell

21

April 19, 2023

Configuring Input/Output Modules (IOMs)

Menu method



Honeywell

22

April 19, 2023

Configuring IOMs

Control Builder Automatically

Names the IOM

2

1



Honeywell

23

April 19, 2023

Configuring IOMs, contd.

MAC address of the remote rack’s CNI card

Slot number of the CNI inthe processor rack through which this card will communicate

Module slot number



Honeywell

24

April 19, 2023

Assigning IOMs

213

Assigned to CEE



Honeywell

25

April 19, 2023

Question 3: Configuring an IOM

Incorrect. Before you can load IOMs, they must be assigned to the Control Execution Environment.




Correct! Before you can load IOMs, they must be assigned to the Control Execution Environment.


Correct! Before you can load IOMs, they must be assigned to the Control Execution Environment.














Submit Clear

Before loading an IOM, it must be:

A) Activated

B) Assigned

C) Renamed

D) Validated



Honeywell

26

April 19, 2023






Topics



Honeywell

27

April 19, 2023

Loading the Controller, CEE, and IOMs

Not yet loaded



Honeywell

28

April 19, 2023

Verify that the items to load are checked

Note: You can decide to have the modules go to the active state automatically by clicking this checkbox, with the Post Load State selected, to be “Active”

Loading the Controller, CEE, and IOMs, contd.



Honeywell

29

April 19, 2023

Topics


• Configuring the FTEB, Controller and CEE


• Loading the Controller, CEE and IOMs




Honeywell

30

April 19, 2023

Activating a Control Strategy

Select Cold Start

Double-click CEE



Honeywell

31

April 19, 2023

Activating a Control Strategy, contd.

Click Yes

Blue: The object is not running (inactive)

Green: The object is running (active)

Red: Communication failure



Honeywell

32

April 19, 2023

Summary

• When configuring and loading C200 hardware and I/O in Control Builder, remember:

– To determine the IOM slot number of hardware in the C200 chassis, start counting at zero, but do not count the power supply, count from left to right and count both spaces, if the module occupies two spaces

– An FTEB node number can be set to higher than 99

– The Supervisory MAC address of the CPM is the MAC address of the CNI card connected to the server

– Before loading the Control Processor Module (CPM), its Control Execution Environment (CEE), and I/O modules (IOMs):

• Configure the CPM, its CEE and I/O modules (IOMs)

• Assign the IOMs to the CEE



Honeywell

33

April 19, 2023

Conclusion

Describe the Configuration of C200 Hardware and I/O

CompletionCompletionCertificateCertificate

Proceed to the next lesson in your course material



Honeywell

34

April 19, 2023

This page intentionally left blank



35April 19, 2023

Describe the Import/Export Procedure in Control Builder

C200 Hardware Configuration Describe the Import/Export Procedure in Control Builder C200 Hardware Configuration Describe the Import/Export Procedure in Control Builder


Honeywell

36

April 19, 2023

Introduction

• In this lesson you will learn to import and export control strategy configurations from one server to another

• At the conclusion of this lesson, you will be able to:

– Describe how to export control strategy configurations from a Control Builder project

– Describe how to import control strategy configurations into a Control Builder project

C200 Hardware Configuration Describe the Import/Export Procedure in Control Builder


Honeywell

37

April 19, 2023

Control Builder - Export

• The Export function lets you export all or a portion of the ERDB viewed in the Project Tree to the Ixport folder or a user-defined location

• The exported portions or all of the ERDB are stored in the Ixport folder at directory location– C:\Program Files\Honeywell\

Experion PKS\Engineering Tools (by default)



Honeywell

38

April 19, 2023

Ixport Directory

Control Builder(Server 1)

Control Builder(Server 2)

Control Strategy Configuration

Project Tree

Control Strategy Configuration

Project Tree

Export Data

Import Data

Control Builder – Import/Export

CM, SCM and hardware configurations can be moved between servers using the Import/Export function



Honeywell

39

April 19, 2023

Control Builder – Export

• In Control Builder, select File > Export to call up the dialog box shown:

All items in Current project

Import\Export text files target location

All items in current project use selection buttons (or use <Ctl> + mouse select or <Shift> + mouse select to export specific CMs from the point window)

List of items to Export based on selections from window(Export.sl)

Select to start export



Honeywell

40

April 19, 2023

Control Builder – Export, contd.

Exporting Data Dialog Box



Honeywell

41

April 19, 2023

Control Builder – Import

• In Control Builder, select File > Import to call up the dialog box shown:

All items in Current Import/Export text Files location

Import\Export text Files target location

Import and Assign

Select to start Import

Use selection buttons (or use <Ctl> + mouse select or <Shift> + mouse select to import specific CMs from the Point window)

When enabled, Your own list of items to import (Filename.sl)

List of items to Import based on Selections from Window (Import.sl)



Honeywell

42

April 19, 2023

Question 1: Importing and Exporting

Incorrect. CMs, SCMs and the hardware configuration can be copied and restored to

another server.



another server.


Correct! CMs, SCMs and the hardware configuration can be copied and restored to

another server.


Correct! CMs, SCMs and the hardware configuration can be copied and restored to

another server.



another server.



another server.



another server.



another server.






Submit Clear

Which of the following statements best describes the import/export function?

A) Only the hardware configuration can be moved between servers

B) CMs, SCMs, and the hardware configuration can be copied and restored to another server

C) Only CMs can be moved between servers

D) None of the above



Honeywell

43

April 19, 2023

Summary

• The Import/Export function in Control Builder:

– Allows you to copy CM, SCM, and hardware configurations from one server’s ERDB to another server’s ERDB



Honeywell

44

April 19, 2023

Conclusion

Describe the Import/Export Procedure in Control Builder

CompletionCompletionCertificateCertificate

Proceed to the Configure C200 Hardware in a Simulation Control Environment (SCE) and Import the Remaining I/O Modules into the SCE

lab exercises



Documents

06 20R300 1 C200 Hardware Configuration