01 - Omc231210 Bsc6900 Wcdma v900r012 Commissioning Issue 1.00 Temm

www.huawei.com

Copyright © 2009 Huawei Technologies Co., Ltd. All rights reserved.

BSC6900 UO V900R012

Commissioning

Copyright © 2010 Huawei Technologies Co., Ltd. All rights reserved. Page1

Foreword

The commissioning is performed after the hardware

installation and before the services are provided

The OMU operating system is installed before the OMU is

delivered

The commissioning ensures the RNC works properly as

designed


References

“BSC6900 UMTS OMU Administration Guide”

“BSC6900 UMTS Commissioning Guide”


Objectives

Upon completion of this course, you will be able to:

Describe BSC6900 commissioning procedure

Outline OMU software functions

Complete BSC6900 commissioning

Complete BSC6900 application software installation


Contents

1. BSC6900 O&M System Introduction

2. BSC6900 Software Installation

3. BSC6900 Commissioning


BSC6900 O&M Subsystem Component

LMT

OMUa boards

SCUa boards

OM modules

on other boards


BSC6900 O&M SubsystemBSC6900 O&M system adopts server and client mode

OMU as a server

LMT as a client

EMS (Element Management System) system

iManager M2000 works for integrated O&M


OMU IP Address Planning

IP Address Planning Principle

Internal fixed IP

address

The preset IP addresses of the internal Ethernet adapters are:

Active BAM: 80.168.3.50 (255.0.0.0)

Standby BAM: 80.168.3.60 (255.0.0.0)

External fixed IP

address

The preset IP addresses of the external Ethernet adapters are:

Active BAM: 172.121.139.201 (255.255.255.0)

Standby BAM: 172.121.139.202 (255.255.255.0)

The settings can be reconfigured on site based on the actual

networking topology


OMU IP Address Planning

IP Address Planning Principle

Internal/External

virtual IP address

The virtual IP address is set in the same subnet with the internal/

external fixed IP addresses of the active and standby BAMs

Backup channel

IP addresses

The preset backup channel IP addresses of the active and standby

BAMs are:

Active BAM: 192.168.3.50 (255.255.255.0)

Standby BAM: 192.168.3.60 (255.255.255.0)

The IP address should not be changed

Commissioning IP

address

The preset commissioning IP addresses are:

Active BAM: 192.168.6.50 (255.255.255.0)

Standby BAM: 192.168.6.60 (255.255.255.0)

The IP address should not be changed.


OMU Internal Network IP Address Planning

Active OMUa

Internalnetworksegment

Standby OMUa

80.168.3.50/880.168.3.50/8 80.168.3.60/880.168.3.60/8

SCUa SCUa

Backboard

Intel Ethernet adapters

Intel Ethernet adapters

192.168.3.50/24192.168.3.50/24 192.168.3.60/24192.168.3.60/24

Dedicated backup channel

BSC6900 FAM

Virtual IP

80.168.3.40/8

Virtual IP

80.168.3.40/8

ETH4-SCU7

ETH5-SCU6

ETH4-SCU7

ETH5-SCU6

ETH3-UPDATE

ETH3-UPDATE


OMU External Network IP Address Planning

Active OMUa

LMT/M2000

Standby OMUa

ExternalnetworkSegment GE adapter

172.121.139.201/24172.121.139.201/24 172.121.139.202/24172.121.139.202/24

Virtual IP 172.121.139.200/24Virtual IP 172.121.139.200/24

ETH0

ETH1

ETH2

ETH0

ETH1

ETH2

192.168.6.60/24192.168.6.60/24

192.168.6.50/24192.168.6.50/24

Hub

Commissioning Ethernet adapter


Contents





BSC6900 Software

Dopra Linux Mysql Database

OMU Application

OMU Server

MPS/EPS

Host Software

ProgramFile

Patch File(optional)

Data File

LMT

Windows XPSP2

Java Environment

LMT Software


OMU Software

The OMU software

consist of multi-

level service

monitoring entities

and service

processes


OMU Software Installation Procedure

Obtain the Installation Information on the OMU

Remotely Logging In to the OMU

Uploading the OMU Application Installation Package to

the OMU

Installing the OMU Application in the Active Workspace

Checking the Installation Directory of the OMU

Applications

Checking the Status of omud Process


Obtain the Installation Information on the OMU

Before the installation, obtain the following information

from Data Sheet of BAM Software Installation

Password of the operating system administrator

Fixed IP addresses of the internal and external networks


Remotely Logging In to the OMU

On the computer run the

SSH terminal, PuTTY

Enter the IP address of

the OMU

Log in to the OMU as

user root


Uploading the OMU Application Installation Package to the OMU

Decompress the BSC6900 version software package to the

local drive D

Log in to the OMU through the psftp software

Run the lcd D:\ to set the local directory

Run the mkdir /mbsc/upgrade to create the target directory

Run the cd /mbsc/upgrade to go to the target directory

Run the put -r V900R012C00 to upload the OMU application

installation packet to the OMU

After the loading is complete, enter the exit command to exist the

psftp software


Installing the OMU Application in the Active Workarea

On the PuTTY terminal, run the following commands

cd /mbsc/upgrade/V900R012C00/install/setup

chmod +x ./install_bam.sh

./install_bam.sh

Enter the run mode

Setting the office name

Setting the language

Setting the admin/FTP password

Setting the external virtual IP address

Setting the OMU system type


Checking the Installation Directory of the OMU Applications

Log in to the OMU by PuTTY

Run the cd /mbsc/bam

Check whether the OMU

installation directory


Checking the Status of omudProcess

Log in to the OMU by PuTTY

Run the /etc/rc.d/omud status

The returned information is running, it means the omud is

working normally

The returned information is unused, run the /etc/rc.d/omud

start command to start the omud

The returned information is neither running nor unused,

reinstall the OMU application in the active workspace


Contents





Contents


3.1 BSC6900 Commissioning Introduction

3.2 BSC6900 Commissioning Procedure


Introduction to BSC6900 Commissioning

Definition of BSC6900 Commissioning

The commissioning of equipment, BSC6900 board

software and data file loading , interfaces verification ,

and services verification after hardware installation

To ensures that the BSC6900 works properly as designed


Preparation For BSC6900 Commissioning

Preparation For BSC6900 Commissioning

Verify hardware status

BSC6900 hardware is installed and passed the hardware installation check and powering-on check

OMU is configured before delivery

LMT PC meets the configuration requirements

Software preparation

BAM and LMT application software are ready

License file is ready

MML command script for initial configuration is ready


Preparation For BSC6900 Commissioning (Cont.)

Verify commissioning network status

At least one BTS and one NodeB are connected to the local BSC6900. The BTS and the NodeB should have passed commissioning and can provide basic functions

At least one set of Core Network (CN) equipment is connected to the local BSC6900. The CN equipment should have passed the commissioning and can provide basic functions

If the BSC6900 is connected to the RNC, then that RNC must have passed the commissioning

Three single-mode UEs, three single-mode MSs and one dual-mode UE are ready for test and are registered in the HLR


Contents


3.1 BSC6900 Commissioning Introduction

3.2 BSC6900 Commissioning Procedure


BSC6900 Commissioning Procedure

Commissioing Prerequsites

Check hardware operating Status

Verify OMU through USB Disk

Verify OMU Locally

Log in to BSC6900 through LMT

Update OMU Database

Activate and Verify the License

Load BSC6900 Board Software and Data

files

Connect BSC6900 to M2000

Local operation

Local operationRemote operation

based on local coopertation

Remote operation

Remote operation

Continued in the next page


BSC6900 Commissioning Procedure (Cont.)


Checking the Operating Status of the Hardware

Before verifying the equipment, ensure that the cabinet is

powered on and operates normally

Checklist of the power supply to the cabinet components


Verifying the OMUVerifying the OMU locally

Log in to the OMU through PuTTY

Checking the operation status of the OMU

Checking the version of the OMU application

Changing the external fixed IP address, the external virtual IP

address

Verify the active OMU and the standby OMU respectively

If OMU application is not installed or abnormal, please

reinstall software


Verifying the OMU (Cont.)

Verifying the OMU through USB Disk

Preparing the USB disk

Installing the operating system

Verifying the LMT

Log in to the BSC6900 through the LMT

Run the MML command LST VER to check the version of OMU


Updating the OMU Database

Run the MML command script to update the OMU database

Method 1 : through MML commands

Run the MML command SET CFGDATAINEFFECTIVE repeatedly to

set all the subracks to the ineffective mode

Run the MML command RST DATA. A dialog box is displayed. Click

Yes to initialize the BSC6900 configuration data in the OMU database

Upload the MML command script to the /ftp folder in the OMU active

workspace directory

Run the MML command RUN BATCHFILE to run the MML script file


Updating the OMU Database (Cont.)

Method 2 : through GUI

Run the MML command SET CFGDATAINEFFECTIVE repeatedly to

set all the subracks to the ineffective mode

Run the MML command RST DATA. A dialog box is displayed. Click

Yes to initialize the BSC6900 configuration data in the OMU database

On the LMT, click the Batch tab to enter the Batch panel

Click Open and open the batch file

Click Go to execute the batch file


Activating and Verifying the License

Activating and Verifying the License

Downloading license to OMU active workspace directory

/ftp/license (DLD LICENSE)

Querying the detail information of the license file (LST

LICENSE)

Activating the license file (ACT LICENSE)

Checking the license consistency between host and OMU

(CMP LICENSE)


Loading the BSC6900 Board Software and Data Files

Loading the BSC6900 Board Software and Data Files

Generating the Data File

Clear the data in the BAM database (RST DATA)

Generate the data file in ineffective state

– SET CFGDATAINEFFECTIVE

– Batch Commands

– FMT DATA

Setting the Loading Mode (SET LODCTRL)

Loading the MPS/EPS/TCS (RST SUBRACK)

Checking the consistency of the data and the version (ACT CRC &

CMP BRDVER)


Verifying the Iub Interface

Verifying the Iub Interface (over ATM)

Verifying Physical Links at the BSC (DSP E1T1 & DSP OPT)

Verifying the Control Plane on the Iub Interface (DSP

SAALLNK & DSP UIUBCP & DSP ADJNODE)

Verifying the User Plane on the Iub Interface (DSP

AAL2PATH)

Verify the Management Plane on the Iub Interface (DSP

IPOAPVC)

Verifying the Cell Setup (DSP UCELL)


Verifying the Iub Interface (Cont.)

Verifying the Iub Interface (over IP)

Verifying Physical Links at the BSC (DSP ETHPORT & DSP

OPT)

Verifying the Control Plane on the Iub Interface (DSP

SCTPLNK & DSP UIUBCP & DSP ADJNODE)

Verifying the User Plane on the Iub Interface (DSP IPPATH)

Verify the Management Plane on the Iub Interface (DSP

IPOAPVC)

Verifying the Cell Setup (DSP UCELL)


Verifying the Iu-CS Interface

Verifying the Iu-CS Interface (over ATM)


Verifying the Control Plane on the Iu-CS Interface

– DSP SAALLNK

– DSP MTP3LNK

– DSP SSN

– DSP N7DPC

– DSP ADJNODE

Verifying the User Plane on the Iu-CS Interface (DSP

AAL2PATH)


Verifying the Iu-CS Interface (Cont.)

Verifying the Iu-CS Interface (over IP)


OPT)

Verifying the Control Plane on the Iu-CS Interface

– DSP SCTPLNK

– DSP M3LNK

– DSP SSN

– DSP N7DPC

– DSP ADJNODE

Verifying the User Plane on the Iu-CS Interface (DSP IPPATH)


Verifying the Iu-PS Interface

Verifying the Iu-PS Interface (over ATM)


Verifying the Control Plane on the Iu-PS Interface

– DSP SAALLNK

– DSP MTP3LNK

– DSP SSN

– DSP N7DPC

– DSP ADJNODE

Verifying the User Plane on the Iu-PS Interface (PING IP)


Verifying the Iu-PS Interface (Cont.)

Verifying the Iu-PS Interface (over IP)


OPT)

Verifying the Control Plane on the Iu-PS Interface

– DSP SCTPLNK

– DSP M3LNK

– DSP SSN

– DSP N7DPC

– DSP ADJNODE

Verifying the User Plane on the Iu-PS Interface (DSP IPPATH)


Handling the Alarms Generated During the Commissioning

Handling Alarms During RNC Commissioning

Checking alarm on the LMT

Handling the Alarms by LMT online help

Handling alarms by HUAWEI Technical Support


Verifying the UMTS Services

To be sure BSC can provide services defined in license file

Basic services

Voice service, CS stream service, PS service, mobility

management, and OM management

Feature services

Inter-system handover, HSDPA service, HSUPA service,

MBMS service, and location service


Connecting the BSC6900 to the M2000

Connect the BSC6900 to the OM network

Configure the IP route from the BSC6900 to the M2000

(ADD OMUIPRT & ADD EMSIP)

Create the BSC6900 on the M2000

iManagerTM M2000

DCN


Creating Scheduled Tasks

Scheduled tasks for backing up system data (ADD

SCHTSK & ADD SUBTSK)

Scheduled tasks for backing up logs (ADD SCHTSK & ADD

SUBTSK)

Thank youwww.huawei.com

Documents

01 - Omc231210 Bsc6900 Wcdma v900r012 Commissioning Issue 1.00 Temm