01-4 Local Office Data.pdf

7/28/2019 01-4 Local Office Data.pdf

1/25

M900/M1800 Base Station Controller

Initial Configuration Manual Contents

Issue 07 (2006-08-20) Huawei Technologies Proprietary i

Contents

4 Local Office Data........................................................................................................................4-7

4.1 Overview.......................................................................................................................................................4-8

4.2 Configuring Local Office Information ........................................................................... ...............................4-8

4.1.1 Configuring Network Property............................................................................................................4-8

4.2.2 Configuring Location Property .......................................................................... ..................................4-9

4.2.3 Configuring Interface Property ................................................................. .........................................4-10

4.3 Configuring System Property......................................................................................................................4-11

4.1.1 Configuring Alarm Parameter Table ..................................................................... ............................ 4-11

4.3.2 Configuring Semi-permanent Connection ................................................................. ........................4-12

4.3.3 Configuring BTS Software Index ...................................................................... ................................4-13

4.3.4 Configuring Common Parameter Table ...................................................................... .......................4-14

4.3.5 Configuring Flow Control..................................................................................................................4-18

4.3.6 Configuring Reserved Parameter ..................................................................... ..................................4-19

4.4 Loading Board Software .......................................................... ................................................................... 4-20

4.5 Configuring BSC BIE Semi-perm. Con. .......................................................... ...........................................4-21

4.6 Configuring Advanced Property..................................................................................................................4-22

4.6.1 Configuring SS7.................................................................................................................................4-22

4.6.2 Configuring Other Properties.............................................................................................................4-24

4.6.3 Configuring A Interface Timeslot Occupies..................................... .................................................. 4-25

4.6.4 Configuring Timer Data.....................................................................................................................4-26

4.7 Confirming Modification .................................................................. .......................................................... 4-27


2/25


Initial Configuration Manual Figures

Issue 07 (2006-08-20) Huawei Technologies Proprietary iii

Figures

Figure 4-1 [Local Office Information] tab page ...................................................................... ...........................4-8

Figure 4-2 Configure network property..............................................................................................................4-9

Figure 4-3 Configure location property............................................................................................................4-10

Figure 4-4 Configure interface property...........................................................................................................4-10

Figure 4-5 Configure system flow control property.........................................................................................4-11

Figure 4-6 Password verification......................................................................................................................4-11

Figure 4-7 Alarm Parameter Table .................................................................. ................................................. 4-12

Figure 4-8 Semi-permanent Connection Table.................................................................................................4-13

Figure 4-9 BTS Software Configuration ...................................................................... ....................................4-13

Figure 4-10 Add Configuration Item................................................................................................................4-14

Figure 4-11 configure common parameter .............................................................. .........................................4-15

Figure 4-12 configure soft parameter ........................................................... .................................................... 4-16

Figure 4-13 Module description table .............................................................. ................................................ 4-17

Figure 4-14 Password verification....................................................................................................................4-18

Figure 4-15 Set Flow Control Table ................................................................. ................................................ 4-19

Figure 4-16 Reserved Parameter Configuration...............................................................................................4-20

Figure 4-17 BSC Board Software Loading Table.............................................................................................4-21

Figure 4-18 Add BSC Board Software Loading Information...........................................................................4-21

Figure 4-19 BSC BIE Semi-perm. Conn..........................................................................................................4-22

Figure 4-20 [SS7 Signaling] tab page...............................................................................................................4-23


3/25

Figures


Initial Configuration Manual

iv Huawei Technologies Proprietary Issue 07 (2006-08-20)

Figure 4-21 Others properties...........................................................................................................................4-24

Figure 4-22 A Interface Timeslot Occupies......................................................................................................4-26

Figure 4-23 Timer Data .................................................................. .................................................................. 4-26


4/25


Initial Configuration Manual Tables

Issue 07 (2006-08-20) Huawei Technologies Proprietary v

Tables

Table 4-1 Description of the parameters related to network property configuration ..........................................4-9

Table 4-2 Description of the parameters related to location property configuration. .......................................4-10

Table 4-3 Description of the parameters related to interface property configuration. ...................................... 4-11

Table 4-4 Meaning of soft parameter................................................................................................................4-16

Table 4-5 Description of the parameters...........................................................................................................4-18

Table 4-6 Description of the parameters in [SS7 Signaling].............................................................................4-23

Table 4-7 Description of the parameters in [Others].........................................................................................4-24


5/25


Initial Configuration Manual 4 Local Office Data

Issue 07 (2006-08-20) Huawei Technologies Proprietary 4-1

4 Local Office Data

About This Chapter

The following table lists the contents of this chapter.

Title Description

4.1 Overview Introduces the main idea of this chapter.

4.2 Configuring Local OfficeInformation Describes the procedure for configuring the local officeinformation.

4.3 Configuring SystemProperty

Describes the procedure for configuring the systemproperty.

4.4 Loading Board Software Describes the procedure for loading the board software.

4.6 Configuring AdvancedProperty

Describes the procedure for configuring the advancedproperty.

4.7 Confirming Modification Describes the procedure for confirming modification.


6/25

4 Local Office Data



4-2 Huawei Technologies Proprietary Issue 07 (2006-08-20)

4.1 Overview

BSC local office data configuration is of great significance, and has direct impact upon the

normal operation of the GMPUs in BSC.

BSC local office information describes SS7 information in BSC, e.g., OPC, DPC, SCCP, etc.

And the GSM specification supported by each interface (A/Abis/Um interface).

4.2 Configuring Local Office Information

Select the [Local Office Information] tab page in BSC Auto Data Configuration System, asshown in Figure 4-1.

Figure 4-1[Local Office Information] tab page

4.1.1 Configuring Network Property

Configure network property, as shown in Figure 4-2.


7/25




Figure 4-2Configure network property

See Table 4-1 for the description of the parameters related to network property configuration.

Table 4-1Description of the parameters related to network property configuration

Parameter name Default

value

Description

Signaling NetworkIndicator

NationalStandby

As per the actual conditions, configure thesignaling network that OSP belongs to.

BSC Signaling PointCode

None Namely, OPC. Configure this parameter as perthe network plan.

MSC Signaling PointCode

None Namely, DPC. Configure this parameter as perthe data in the peer MSC.

z All the SPCs of Huawei GSM equipment is indicated by hexadecimal. Please convert the SPCs if

there are indicated by decimal digits in relevant documents. Generally, SPC is a 14-bit signaling

code, and may be a 24-bit signaling code. To meet the various requirements of different MSCs, SPCshould be configured based on negotiation.

z When signaling abnormality occurs, user can check whether the first digit of hexadecimal in SPC is

"0", and can attempt to add "0" to or remove "0" from the first digit. "0" will change the valid bitnumber of SPC, the method to identify the number of SPC is different between different MSC.

For the detail information on the parameters, please refer to M900/M1800 Base Station

Controller Data Configuration Reference - Engineering Parameters.

4.2.2 Configuring Location Property

Configure location property, as shown in Figure 4-3.


8/25

4 Local Office Data




Figure 4-3Configure location property

See Table 4-2 for the description of the parameters related to location property configuration.

Table 4-2Description of the parameters related to location property configuration.

Parameter name Defaultvalue

Description

Country Code None Namely, CC, the country code registered by MS. Forexample, the CC of China is "86".

Mobile CountryCode

None Namely, MCC, uniquely identifying the country that

MS belongs to. For example, the MCC of China is"460".

Local Area Code None Toll call area code for the area where BSC is located.

Mobile Network

Code

None Namely, MNC, identifying the PLMN that MS belongs

to.



4.2.3 Configuring Interface Property

Configure interface property, as shown in Figure 4-4.

Figure 4-4Configure interface property

See Table 4-3 for the description of the parameters related to interface property configuration.


9/25




Table 4-3Description of the parameters related to interface property configuration.

Parameter name Default value Description

A Interface Version GSM_Phase_2 Select an interface version as per the GSM

protocol criterion which is adopted by the Ainterface provided by MSC.

Abis InterfaceVersion

GSM_Phase_2 None

Um Interface Version GSM_Phase_2 None



4.3 Configuring System Property

Configure system property, as shown in Figure 4-5.

Figure 4-5Configure system flow control property

4.1.1 Configuring Alarm Parameter Table

In Figure 4-5, click , The interface will pop up as shown in Figure 4-6.

Figure 4-6Password verification

Input supervisor password, and click , the interface will pop up as shown in Figure 4-7.


10/25

4 Local Office Data




Figure 4-7Alarm Parameter Table

Modify the parameters of alarm.



4.3.2 Configuring Semi-permanent Connection

The semi-permanent connection is to provide a transport path with the bandwidth of 64 kbit/s

for customer. It is used to transmit business hall information, BTS AC power alarminformation and other maintenance information.

Click in Figure 4-5, the interface will pop up as shown in Figure 4-8.


11/25




Figure 4-8Semi-permanent Connection Table

For the detail information on the parameters, please refer to M900/M1800 Base StationController Data Configuration Reference - Engineering Parameters.

4.3.3 Configuring BTS Software Index

This index is the one of BTS board software. Only when there is a corresponding record in[Site Software Configuration Table], can the BTS board software be loaded and activated.


Figure 4-9BTS Software Configuration


12/25

4 Local Office Data




Click to pop up the interface as shown in Figure 4-10.

Figure 4-10Add Configuration Item

Input relevant information of the to-be-configured BTS software.



4.3.4 Configuring Common Parameter Table

The default configuration is adopted to all common parameter except software parameter.



13/25




Figure 4-11configure common parameter

Switch to Software Parameter Table interface as shown in Figure 4-12.


14/25

4 Local Office Data




Figure 4-12configure soft parameter

Table 4-4 describes the meaning of the software parameters.

Table 4-4Meaning of soft parameter


Encryption algorithm ofdestination BSC

Any Select the Encryption algorithm ofdestination BSC, include A5/1, A5/2, A5/3,A5/4, A5/5, A5/6, A5/7 and Any.

Type of alarm box new alarm box Select the type of alarm box, include old ornew alarm box.

BIE PCM alarm delay(second)

5 Configure BIE PCM alarm delay time, theunit is second and the value rang is 0 to 15.

Include speech versionIE in SDCCH handovermessage

selected When checkbox is selected, speechversionIE is included in SDCCH handovermessage, otherwise, versionIE is included inSDCCH handover message.

Always include cell IDIE in assignmentcomplete message

not selected When checkbox is selected, cell ID IE mustbe included in assignment completemessage, otherwise, cell ID IE is included in

assignment complete message if service cellchange when assignment channel.


15/25





Exclude CIC pool IE in

assignment completemessage

not selected When checkbox is selected, Exclude CIC

pool IE in assignment complete message,

otherwise, keep the current rule about cicpool in assignment complete message.

Exclude CIC pool IE in

handover completemessage

not selected When checkbox is selected, excluding CIC

pool IE in handover complete message,otherwise, keep the current rule about cicpool in handover complete message.

Support group circuit

operation onA-interface

selected When checkbox is selected, support group

circuit operation on A-interface, otherwisedo not support.

Switch to Module Description Table interface as shown Figure 4-13.

Figure 4-13Module description table

This table is used to configure the PCU ID which the module connects to. The element in thisdialog changes as the module number changes.


16/25

4 Local Office Data




Table 4-5 describes the meaning of the parameters.

Table 4-5Description of the parameters

Parameter Default Description

PCU ID of Module [n] 1 The ID of the PCU that the module [n] connects

to.

4.3.5 Configuring Flow Control

In Figure 4-5, click , the interface will pop up as shown in Figure 4-14.

Figure 4-14Password verification

Input supervisor password, and click . The interface will pop up as shown in Figure

4-15.


17/25




Figure 4-15Set Flow Control Table

Modify the parameters of flow control.

4.3.6 Configuring Reserved Parameter

It is used to configure reserved parameter in order to upgrade BSC host.

Click in Figure 4-5. The interface will pop up as shown in Figure 4-16.


18/25

4 Local Office Data




Figure 4-16Reserved Parameter Configuration

Reserved parameter of each BM, site, cell, TRX can be configured in Figure 4-16.

The button in Figure 4-5 can be clicked only after all TRXs have been assignedto cells.

4.4 Loading Board Software

This subsection is to configure BSC board software. If BSC board software (e.g. GMEM)need be loaded, relevant information should be configured.

Click in Figure 4-1. The interface will pop up as shown in Figure4-17.


19/25




Figure 4-17BSC Board Software Loading Table

Click to pop up the interface as shown in Figure 4-18.

Figure 4-18Add BSC Board Software Loading Information

Input the BSC board software loading information,



4.5 Configuring BSC BIE Semi-perm. Con.

There is none concrete connection between trunk circuit and BSC BIE port in the three trunkrelay mode, which is, 6 port half rate topology, half rate ring topology and full rate ring


20/25

4 Local Office Data




topology, so BSC BIE semi-perm. Con. must be configured in order to indicate the connectionrelationship between trunk circuit and BSC BIE port.

Click < BSC BIE Semi-perm. Con.> in Figure 4-1, the interface will pop up as shown in

Figure 4-19.

Figure 4-19BSC BIE Semi-perm. Conn.



4.6 Configuring Advanced Property

4.6.1 Configuring SS7

Click in Figure 4-1 to pop up the interface as shown in Figure 4-20.


21/25




Figure 4-20[SS7 Signaling] tab page

Modify the parameters of SS7.

See Table 4-6 for the description of the parameters in [SS7 Signaling].

Table 4-6Description of the parameters in [SS7 Signaling]


Signaling NetworkCoding Mode

National Standby:14bit

Others: Not Used

It must be configured in consistencywith the value of [Signaling NetworkIndicator] in Figure 4-2.

SCCP Link Both None

SP Function Identity Selected -

STP Function Identity Deselected This parameter is to indicate whether

OSP provides the signaling transferfunction.




22/25

4 Local Office Data




4.6.2 Configuring Other Properties

Switch the Figure 4-20 to the interface as shown in Figure 4-21.

Figure 4-21Others properties

Configure the other properties.

See Table 4-7 for the description of the parameters in [Others].

Table 4-7Description of the parameters in [Others]


Echo Cancellation Not Supported When SS7 signaling messages are to be

transferred via a satellite, the echocancellation function should be enabled toprovide a high-quality voice channel.

Voice Encode/DecodeOptimization

NormalEncode/Decode

None

Allowed TransmissionDelay

10 None

Restart Function Selected None

Support Cell Broadcast Selected None

High Band Support DCS1800 This parameter is used to decide whether the

current BSC supports DCS1800 orPCS1900. It does not support dynamic

configuration.


23/25





LCS (Cell ID+TA)

Allowed

No Used to determine whether the BSC cell

provides LCS (Cell ID+TA) or not.

TC OWA Check Time 255 FTC OWA Check Time can be started orclosed dynamically. Check Time means:

FTC tests the UL/DL voice service of theoccupied timeslots. If it fails to receive theUL/DL voice frame in a specified period(for example, 5 s), it reports alarm to MPU.

GPRS Suspend TimerValue

5 If initiates a call to a MS that is carrying out

PS service, the PS service is suspended andthen resumed.

The suspend flow: After send the message

GPRS Suspend Request to PCU,,BSC starts

the GPRS Suspend Timer Value and waitfor the PCU returns the Ack or Nackmessage. If BSC does not receive the

response of PCU within the set timeof GPRS Suspend Timer Value, BSC setsthe status of the GPRS in CCB as no

response received. The resume flow is notstarted.

Inter system HO

allowed

Not selected Used to indicate whether the BSC supports

inter system HO.



4.6.3 Configuring A Interface Timeslot Occupies



24/25

4 Local Office Data




Figure 4-22A Interface Timeslot Occupies

Configure the parameters properly.

Refer to Chapter 5 Trunk & Signaling Data of A Interface for the description of theparameters in the [A Interface Timeslot Occupies] tab page.

4.6.4 Configuring Timer Data


Figure 4-23Timer Data


25/25



Configure the parameters of timer data.

4.7 Confirming Modification

In Figure 4-1, click to save the modified data.

Documents

01-4 Local Office Data.pdf