The Savant Wi-Fi Circa Controller (WCC-2XXXXX) Quick Reference Guide provides the information necessary to install the WCC-2XXXXX. The wireless Circa controller functions as two dimmers and a controller combined in a single keypad. The SmartConnect adapter and the SmartConnect app enables the WCC-2XXXXX to be configured with an iOS device even when the Wi-Fi network is not available. The following fixtures are supported by the WCC controller: incandescent, LED, halogen, fluorescent, compact fluorescent, cold cathode, and neon. They must be dimmable forward phase loads. For dimmable lighting, a minimum of three-watt load can be dimmed.

Front View of Six-Button WCC-2XXXXX with Faceplate

Box Contents(1) WCC-2XXXXX (1) Installation Kit: (4) 6-32 x1 Flat Phillips Screw (039-0103-xx)(1) Quick Reference Guide (this document)

Optional ComponentsSmartConnect Accessory (SCA-CONF or SCA-CONFL)SmartConnect appMicro USB-B to Lightning Adapter (SCA-ADPT)

SpecificationsEnvironmentalEnvironmentalTemperature 32° to 104° F (0° to 40° C)Humidity 10% to 90% Relative Humidity (non-condensing)Dimensions with Faceplate Dimensions with Faceplate Height 4.69 in/11.92 cmWidth 4.85 in/12.33 cmDepth 1.82 in/4.63 cmPowerPowerSupply 120/240V AC, 50/60 HzLoad PowerLoad PowerMinimum 3 watts per gang

Maximum

• 550 watts per channel (1100 watts total)—the maximum rating for dimmer version (no relay version on two gang)

• 550 watts (per channel) even if only one channel is being used• If a-one-gang and two-gang are used together, assume the maximum

load of each.ComplianceCompliance

Safety and Emissions

FCC Part 15 | CE Mark | C-Tick | UL

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Any changes or modifications of this product, not approved by manufacturer will void the user’s authority to operate the equipment.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditionssuivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

RoHS CompliantMinimum Requirement: Release LiteWare 5.2Minimum Requirement: Release LiteWare 5.2

Warning: A licensed electrician is required to install a Savant Wi-Fi Circa Controller keypad.

NOTE: Savant recommends a U.S. back box with a depth of 3.5 in/8.89 cm. Minimum depth is 2.5 in/6.35 cm.

.

WCC-2XXXXX

Exploded View of WCC-2XXXXX

Electrician Installation Instructions: WCC-2XXXXXTo ensure proper installation of your Wi-Fi keypads, a qualified electrician should do the following.

1. Isolate and turn off the power from the main power supply to the switch/keypad that is to be replaced.2. Unscrew the wall plate and remove.3. Remove existing toggle/rocker switch or analog dimmer.4. Unscrew the sheathed, insulated wires (Romex) from the screw terminals.5. Remove switch box.6. Connect the in-wall Romex wires to the correct screw terminals on the Wi-Fi keypad and tighten terminals.7. Insert the Wi-Fi™ keypad into the backbox and secure with the screws provided.8. Re-establish power from the main power supply.

Service Switch is used to disconnect power from the load for service.

Load 1

Load 2

Neutral

Line

ServiceSwitch

Ground

Rear View of WCC-2XXXXX

Terminal Wire Color Purpose

Load 1 Black Connects from line to first light/load

Load 2 Black Connects from line to second light/load

Neutral White Neutral

Line Black Hot/Live (120/240V AC: 12-14 AWG)

Ground Green Ground (wire/strip gauge)

Back Box Circa Keypad Faceplate

Phillips Screws (4)

082313 009-0971-00 Savant Wi-Fi™ Keypad Deployment Guide 21 of 46

Rear View of WCC-2XXXXX with Callouts

Terminal Wire Color Purpose

Load 1 Black Connects to first light/load, fan or fireplace

Load 2 Black Connects to second light/load, fan or fireplace

Neutral White Neutral

Line Black Hot/Live (120/240V AC: 12-14 AWG)

Ground Green Ground

SmartConnect Port

LED Level

IP Reset

Push To Test 1 button

Push to Test 2 button

Service Switch

Front View without Faceplate

Function Description

Program Port for the SmartConnect adapter

IP Reset Press to reset this device’s IP address

PTT Load 1 Press to test for load 1 (left side)

PTT Load 2 Press to test for load 2 (right side)

LED Level Rotate the wheel to adjust the brightness intensity level of text/icons

Service Switch Pull the switch down to disconnect power from the keypad and load for service. Push it up to reconnect the power.

Wi-Fi™ Circa Controller(WCC-2XXXXX)

Quick Reference Guide009-0970-01

WCC-2XXXXX-00

092413

Installing the Wi-Fi Circa Controller1. Isolate and turn off the power from the main power source to the switch/keypad that is to be

replaced.2. Unscrew the wall plate and remove.3. Remove existing toggle/rocker switch or analog dimmer.4. Unscrew the sheathed, insulated wires (Romex) from the screw terminals.5. Remove switch.6. Connect the in-wall Romex wires to the correct screw terminals on the Wi-Fi keypad and

tighten terminals.7. Insert the Wi-Fi keypad into the backbox and secure with the screws provided.8. Re-establish power from the main power supply.

Push to Test Button When you first install the WCC-2XXXXX, the Push To Test (PTT) button can be used to test the load connected to the dimmer, and also can be used to change the dynamic snubber mode.

The PTT LED (also referred to as a diagnostic LED) will turn on at boot, and will go dim when the dimmer connects to an access point. The PTT LED color is based on the snubber mode as described in the next table. The PTT LED will flash when in Push To Test mode.

PTT LEDsLED State Description

PressA press with no hold will turn on the load, and will flash the PTT LED on bright regardless of the connection state. Pressing the button again will exit PTT mode and return to normal operation.

HoldWhen this button is held for more than two seconds, the snubber mode will be changed to the next available mode at two seconds, four seconds and six seconds. When the button is released, the current snubber mode will be saved to flash.

LED

The PTT LED will change color to indicate the snubber mode as follows:Green - (default) turn snubber on when the load is offRed - snubber always off (magnetic loads)Blue - snubber always on (LED loads)Hold for 10 seconds: Reset to factory defaults - Wi-Fi™ settings will be deleted and the Wi-Fi™ dimmer will revert to factory default mode. On reboot the dimmer will attempt to connect to the open Savant devices access point (two gang controller).Hold during boot: If you hold the diagnostic button for three seconds while the dimmer is booting, the dimmer will go into GainSpan programming mode. In this mode the SmartConnect port is internally routed to the GainSpan for programming through a SmartConnect serial cable.

Setting Up Wi-Fi Using SmartConnect

Micro USB-B(male)

Micro USB-B(male)

SmartConnect using SCA-CONF SmartConnect using SCA-CONFLThis procedure assumes that you have already installed the Savant SmartConnect app on your iOS device, and that you have connected the SmartConnect cable to the appropriate Savant device and iOS device. The next procedure applies to both SmartConnect accessories SCA-CONF or SCA-CONFL.

To configure your Savant Wi-Fi keypad wireless network settings using the SmartConnect app when the Wi-Fi network is not available on an iOS device, do the following.

1. Remove the faceplate.2. Connect the SmartConnect Accessory (SCA-CONF or SCA-CONFL) to the iOS device.3. Open the SmartConnect app on the iOS device.4. Attach the SmartConnect adapter to the Wi-Fi keypad on the front of the keypad.5. In the app, under Double Gang Wi-Fi, select the Wi-Fi row.6. Select a network using one of the following:

• If you tap an option under Use current Wi-Fi network of this iPad, you must share the settings. Then, the Wi-Fi settings are complete.

• If you tap an option under Recent networks, that network is used by your Savant Wi-Fi device.• Under Available Networks tap Other… to manually configure the settings. Continue with the

next steps. 7. Enter a network Name. 8. Tap Security and then select an option.9. Tap Password to open the keyboard and then enter the network password. 10. Tap the Join button.

If a static IP address is required, on the Wi-Fi screen and select the Static tab. Next, enter the IP Address, Subnet Mask and Router information. Tap Apply.

Set Up Wi-Fi Using a Web BrowserTo configure your Wi-Fi keypad network settings using a Web browser on your Savant Development Environment (SDE), do the following.

1. On the menu bar of your SDE, select the Wi-Fi icon: 2. View the wireless networks.3. Select the SavantDevices network and wait for it to connect.4. Open a Savant-supported Web browser.5. Enter 192.168.1.1 in the URL address bar.6. If prompted, enter the user name: RPM and password: RPM.

The default webpage will be displayed.7. Select Network from the options.

8. Under the Edit Wi-Fi Settings section press the Scan button to view wireless networks in range or type in the network name manually.

9. If security has been enabled on the desired network select the Security Type from the drop down list and enter the Passphrase. Press the WiFi Set button.

If a static IP address is required, under Edit IPv4 Settings change Configure IPv4 to Manually. Enter required information and press the IPv4 Set button.

10. To save the Wi-Fi configuration press the Commit Changes button. The device will be rebooted and the configured settings will be set.

Set Up Wi-Fi Using an iOS Device1. On the iOS device select the Settings icon.2. Select Wi-Fi.3. View the wireless networks.4. Select the SavantDevices network and wait for it to connect.5. Open your Safari® browser.6. Enter 192.168.1.1 in the URL address bar.7. If prompted, enter the user name: RPM and password: RPM.

The default webpage will be displayed.

8. Select Network from the options.9. Under the Edit Wi-Fi Settings section, press the Scan button to view wireless networks in

range, or type in the network name manually.10. If security has been enabled on the desired network select the Security Type from the drop-

down list and enter the Passphrase. Press the WiFi Set button.

If a static IP address is required, under Edit IPv4 Settings change Configure IPv4 to Manually. Enter required information and press the IPv4 Set button.

11. To save the Wi-Fi configuration, press the Commit Changes button. The device will be rebooted and the configured settings will be set.

Additional DocumentationAdditional information is available at: dealers.SavantSystems.com: Dealer Login > Knowledge Base > Savant Hardware > Keypads

Wi-Fi™ Circa Controller(WCC-2XXXXX)

Quick Reference Guide009-0970-01

WCC-2XXXXX-00

092413

Copyright © 2013 Savant Systems, LLC. SAVANT and RacePoint Blueprint are trademarks of Savant Systems, LLC.All brand names, product names and trademarks are the property of their respective owners. Savant Systems, LLC reserves the right to change product specifications without notice.