57
November 2012 Complete Installation Guide Power Analytics Corporation 10805 Rancho Bernardo Road, Suite 270 San Diego, California 92127 USA ©Copyright 2012 All Rights Reserved

001-Complete Install Guide

Embed Size (px)

DESCRIPTION

PS-analysis

Citation preview

Page 1: 001-Complete Install Guide

November 2012

Complete Installation Guide

Power Analytics Corporation 10805 Rancho Bernardo Road, Suite 270

San Diego, California 92127 USA

©Copyright 2012

All Rights Reserved

Page 2: 001-Complete Install Guide

Complete Installation Guide

1

Table of Contents

System Requirements ................................................................................................................................... 3

Uninstalling EDSA Technical/ DesignBase Software from a Workstation ..................................................... 4

Single Machine Installation ........................................................................................................................... 8

Workstation License File Request .......................................................................................................... 15

Server/Network Installation ....................................................................................................................... 17

Server/Network License File Request ..................................................................................................... 24

Configuring the DesignBase license on a workstation connected to a network ..................................... 27

License Borrowing ....................................................................................................................................... 29

DesignBase 5.0 Workstation Unattended Installation ................................................................................ 32

DesignBase Permissions .............................................................................................................................. 34

Common Install/Uninstall Issues................................................................................................................. 35

1) Error 1919 ...................................................................................................................................... 35

2) Actrix.exe System Error. ................................................................................................................ 36

3) DesignBase icons are not functioning correctly across the top of the program as shown in the

screen below. ................................................................................................................................. 36

4) Receiving an error message that DesignBase DLLs are not registered. ........................................ 37

5) License checker failed with the following error messages ............................................................ 37

6) If you are converting from a single workstation to a server license .............................................. 40

7) Actrix error message appears during DesignBase 5.0 installation or when you try opening it from

your desktop icon. .......................................................................................................................... 40

8) Getting error Messages when opening DesignBase 5.0, saving Drawing file or closing

DesignBase 5.0. ............................................................................................................................. 42

9) License checkout failed with the following error messages continuously showing up even though

the license file is located correctly. (For Windows 7 and Windows Vista users) .......................... 43

Steps to Turn off UAC in Windows 7(Windows Vista is slightly different) ................................................. 45

To Uninstall Using Revo Uninstaller ............................................................................................................ 46

Page 3: 001-Complete Install Guide

Complete Installation Guide

2

How to determine your permanent LAN Ethernet Host ID ........................................................................ 50

Running DesignBase Products with Standard User Rights on Windows XP, Vista and Windows 7............ 52

Page 4: 001-Complete Install Guide

Complete Installation Guide

3

System Requirements

Hardware Requirements Intel Pentium® 4 or AMD Athlon® XP or higher processor

2GB RAM (4 GB recommended)

6GB Available Hard Disk Space

Monitor with at least 1024x768 display resolution (24 bit recommended)

Mouse/pointer

CD-ROM drive

Sound card and speakers (optional for tutorials)

Operating System Requirements Workstation:

Windows 8, Windows 7, Windows Vista, Windows XP, or VMware (Virtual Machine) based on any of

these operating systems.

Server: Windows 7, Windows Vista, Windows XP, Windows Server 2003, Windows Server 2008 or VMware

(Virtual Machine) based on any of these operating systems.

Software Requirements Microsoft Internet Explorer

Microsoft Office 2003 or higher

Windows Installer 4.5

Microsoft .Net framework 4.0 or Higher (necessary for the import and export feature to Excel as well as

Paladin Research Lab)

Important Note! Existing DesignBase 4.0 License File(s) for servers and workstations are compatible with DesignBase 5.0. Please back up your server or workstation license file before uninstalling DesignBase 4.0. Your workstation local license file can be found under X:\DesignBase4\config folder. If you are using a floating license, the license file resides in the license server installation folder. There’s no need to update the license server manager.

Page 5: 001-Complete Install Guide

Complete Installation Guide

4

Uninstalling EDSA Technical/ DesignBase

Software from a Workstation

If you have a previous version of EDSA Technical/DesignBase software installed, you

must uninstall it first before installing DesignBase. If you have never installed EDSA

Technical/ DesignBase on your computer, skip to the Single Machine Installation section

on page 8 or Server/Network Installation on page 17.

To Uninstall Using the Add/Remove Programs

1. If DesignBase4 or previous version was installed on Windows 7 or Windows Vista, please turn

off UAC (User Account Control) before uninstallation. (Please refer to “Steps to Turn off UAC

in Windows 7” on page 45)

2. Before uninstalling, if your projects are saved in DesignBase4, DesignBase3, DesignBase2 or

EDSA2005 folder you should either rename the project folder or copy it to another location to

insure none of your work is lost.

3. If you have created your own database make sure you back up your Data Folder before

uninstalling the program.

Important Note! If you have ever installed EDSA Technical or the previous version of DesignBase had problems working correctly, it is suggested that you run a third party uninstaller which cleans the registry. We recommend REVO Uninstaller. This will remove any Actrix files left behind during uninstall. A free 30-day version of Uninstaller Pro can be downloaded at www.revouninstaller.com. Please go to “To Uninstall Using Revo Uninstaller” section on page 46

.

Page 6: 001-Complete Install Guide

Complete Installation Guide

5

4. From the Start Menu at the bottom left corner of the desktop, choose Control Panel.

Page 7: 001-Complete Install Guide

Complete Installation Guide

6

5. Click on the Add/Remove Programs applet in Control Panel. (If you are using Windows 7,

click “Uninstall a program” under “Programs” menu in the Control Panel.)

6. Remove any DesignBase service pack before removing your previous version of DesignBase

software from the list of programs. (If you are using Windows 7, choose “uninstall.”)

Page 8: 001-Complete Install Guide

Complete Installation Guide

7

7. Select “Yes” to remove DesignBase completely from your workstation.

8. Once the program has been removed, exit Control Panel. Check hard disk drives to make sure the

entire program has been removed.

Page 9: 001-Complete Install Guide

Complete Installation Guide

8

Single Machine Installation

The following steps are required to successfully install DesignBase for the first time. If you have

a previous version of EDSA Technical/DesignBase software on your computer, you must

uninstall it before proceeding. (See Uninstalling EDSA Technical/ DesignBase Software from a

Workstation on page 4.)

1. Exit all programs and turn off any screen-saver and Anti-Virus software on your workstation.

This prevents possible conflicts between the DesignBase Software installer and other programs.

You must have “local administrator rights” on the workstation on which you are

installing the DesignBase software; otherwise the installer will not run.

2. You must have minimum “power user” rights on the computer to access the complete

DesignBase program. If you are set up only as a “user” you will not be able to access any

DesignBase menus. See Running DesignBase Product with Standard User Rights on Windows

XP, Vista and Windows 7 beginning on page 52 for more details.

3. Insert the DesignBase software CD into your CD-ROM drive. If you downloaded DesignBase

installation files, extract all the files from DesignBase5.zip and save them. Then click on the

Setup.exe file to start the installation.

4. The DesignBase Software installer should automatically start.

Page 10: 001-Complete Install Guide

Complete Installation Guide

9

5. If you are using a Microsoft Windows version older than Windows 7, the installer may ask you

to install Windows Installer 4.5 before installing Paladin DesignBase 5.0. (Windows 7 user

skips this step.) Click OK and download the update for your operating system at

http://support.microsoft.com/kb/942288. After installing the update, Windows will ask you to

restart your computer for the change of configuration to take effect. You MUST restart your computer. After restarting your computer, begin from step 3.

6. Click “Next” to start the installation of Paladin Design Base 5.0.

Page 11: 001-Complete Install Guide

Complete Installation Guide

10

7. To continue the installation, read and accept the terms in the license agreement and click

“Next.”

8. Enter your company information then click “Next.”

Page 12: 001-Complete Install Guide

Complete Installation Guide

11

9. Select “Typical” to install DesignBase in its default folder or choose custom to change the

installation folder location, and then click “Next.” Do not use spaces or special characters for the folder name.

Page 13: 001-Complete Install Guide

Complete Installation Guide

12

10. Click “Install” to confirm the installation.

11. The installation may take several minutes. Please be patient.

Page 14: 001-Complete Install Guide

Complete Installation Guide

13

12. At the end of the installation, the screen below will appear. Click “Finish.”

13. The program will ask for the license file. Click “OK”.

Page 15: 001-Complete Install Guide

Complete Installation Guide

14

14. To configure your license, launch Client License Manager from Start > Programs > Paladin

DesignBase > Licensing > Paladin Client License Manager.

15. Make sure the “Local Host License” button is selected. Select LAN Ethernet Host ID to be

your “Host ID”. (See Error! Reference source not found. on page 50.)

Page 16: 001-Complete Install Guide

Complete Installation Guide

15

16. At this point you must contact Power Analytics to obtain your license file. You can call or

submit your request through our website:

Workstation License File Request

Phone:

(858) 675-9211 ext. 4641 or 4604

Monday-Friday 8 am-5 pm Pacific Time

From the Power Analytics Website: Fill out the online request form at:

http://www.poweranalytics.com/services_support/password_install.php You must provide Power Analytics with the following information to receive your license file:

Host ID as it appears in the Paladin Client License manager main window

Package type listed in your DesignBase License Certificate

Additional programs purchased

17. Once you receive your license file from Power Analytics, paste it under the program

configuration folder X:\DesignBase5\Config (where X is the drive on which the program has

been installed).

Page 17: 001-Complete Install Guide

Complete Installation Guide

16

18. Go to Paladin Client License Manager, and select the corresponding HOST ID that was used

by DesignBase to generate your license file. Then click “close” at the bottom of the window

19. Open DesignBase 5.0 from your desktop icon. The software will rebuild its toolbar based on

the features available in your license file.

Page 18: 001-Complete Install Guide

Complete Installation Guide

17

Server/Network Installation

By installing a license server, you will be able to "float" licenses to any PC in your network.

The DesignBase Licensing system supports multiple network adapters. For configuration of local node-

locked licenses or server licenses, customers have the choice of which network adapter to lock the

DesignBase software to by using the “Host ID” pull-down list as shown in the figure below:

IMPORTANT:

Do not install DesignBase 5.0 applications and Paladin Server License Manager on

the same workstation.

The steps below describe how to install Paladin Server License Manager on a server:

1. Exit all programs and turn off any screen-saver software on your server.

2. Insert the DesignBase Program CD into your CD-ROM drive and Cancel windows installer if it

starts automatically.

3. Go to your CD-ROM drive (or the files you downloaded) and click on the “licenseserver” folder.

Click on “setup.exe” to start the license server installation.

Page 19: 001-Complete Install Guide

Complete Installation Guide

18

4. Click “Next” when an InstallShield Wizard window appears.

5. Read and accept the terms in the license agreement and then click “Next.”

Page 20: 001-Complete Install Guide

Complete Installation Guide

19

6. Enter your company information then click “Next.”

7. Select a setup type. If user selects “Custom”, please go to step 8. If user selects “Complete”,

please go to step 9.

Page 21: 001-Complete Install Guide

Complete Installation Guide

20

8. Specify program directory.

Page 22: 001-Complete Install Guide

Complete Installation Guide

21

9. Click “Install” to begin the installation. The installation will finish in a few seconds.

10. Click “Finish”. Paladin Server License Manager will open.

Page 23: 001-Complete Install Guide

Complete Installation Guide

22

11. When the Server License Manager Screen opens, make sure you can see your Server Name or IP

address, and Host ID.

12. If your computer has several Network Identification Cards, remember the one you choose in case

you need to reconfigure or uninstall the license server manager from your computer. Each HOST

ID (NIC physical address) will require a different license file for the packages or programs you

purchased.

Page 24: 001-Complete Install Guide

Complete Installation Guide

23

13. Copy down the IP address/ server name as you will need this information to configure the

workstations.

If you intend to use the server IP address to configure the Paladin server license manager and

your client license manager, verify that the IP address used corresponds to the Host ID (NIC Mac

address) that you selected.

You can check it by going to Start > All Programs > Accessories > Command Prompt.

Type in “Ipconfig /all” and press Enter.

Close the Command Prompt window when done.

Page 25: 001-Complete Install Guide

Complete Installation Guide

24

14. At this point you must contact Power Analytics to obtain your license file that will enable you to

use the program. You can call, fax or e-mail:

Server/Network License File Request

Phone:

(858) 675-9211 ext. 4641 or 4604

Monday-Friday 8 am-5 pm Pacific Time

From the Power Analytics Website: Fill out the online request form at:

http://www.poweranalytics.com/services_support/password_install.php

DesignBase Installation License File Request

You must provide Power Analytics with the following information to receive your license file:

Host ID as it appears in the SLM main window

Package type listed in your DesignBase License Certificate

Additional programs purchased

15. Once you have received your license file, paste it under C:\Program Files\Power

Analytics\Paladin License Server\PALADIN.LIC.

If you need to close your Server License Manager and configure your software license at a later time you

can always retrieve it by going to:

Start > All Programs > Paladin Server > Paladin Server License Manager.

16. Click “Start Server” to configure your license.

Page 26: 001-Complete Install Guide

Complete Installation Guide

25

17. When the “Success” window appears click “OK.”

18. Close Paladin Server License manager and open it again. Make sure the correct package type is

displayed and the additional programs you have selected are showing in the Server License

Manager window.

Page 27: 001-Complete Install Guide

Complete Installation Guide

26

19. You can check the status of your license server settings and health by clicking on

“Viewedsalm.log” file and the “View License File” buttons.

Log File:

Page 28: 001-Complete Install Guide

Complete Installation Guide

27

License File:

Configuring the DesignBase license on a workstation connected to a network

1. Install the DesignBase package purchased by following steps 1 through 11 of the Single Machine

Installation section beginning on page8.

2. Click ‘Finish.”

Page 29: 001-Complete Install Guide

Complete Installation Guide

28

3. The program will rebuild his toolbar and then close.

4. Launch the Client License Manager Screen from Start > All Programs > Paladin DesignBase >

Licensing > Paladin Client License Manager. Make sure the “Use License Server” option button

is selected, the server IP address or the server name is showing.

5. Click “Generate License” and then make sure “Configured Package” shows the package type.

6. Click “Close” once the program has successfully reconfigured its license.

7. Open DesignBase 5.0 from your desktop icon. The software will rebuild its toolbar based on the

features in server license file.

Page 30: 001-Complete Install Guide

Complete Installation Guide

29

License Borrowing

The DesignBase licensing system supports license borrowing. When client computers are

configured to use a DesignBase License Server, the clients can check out a license for a

period of time and use the DesignBase software while disconnected from the network the

license server is attached to. The steps below describe the process involved for

borrowing a license for offline use.

1. From the workstation, open “Paladin License Information” editor from windows start menu.

Page 31: 001-Complete Install Guide

Complete Installation Guide

30

2. Click on “Borrow License” and choose the license return date (the date the license will be

automatically returned to the pool of available licenses) from the “Borrow License” window.

3. Once a license has been borrowed the “License Borrowed” dialog will be displayed as shown

below at which time the “OK” button can be pushed.

4. At this point a license for the configured package and the additional programs will be borrowed.

Page 32: 001-Complete Install Guide

Complete Installation Guide

31

5. If a borrowed license needs to be returned to the pool of available licenses, the “License

Information” window will have a “Return License” button available. Also, the window will show

when the borrowed license is expected to expire (or be automatically returned).

Page 33: 001-Complete Install Guide

Complete Installation Guide

32

DesignBase 5.0 Workstation Unattended

Installation

DesignBase 5.0 installer supports unattended as well as silent installations.

The unattended installation is designed for workstations that will run with a floating license configuration

and does not require any user or administrator interaction during the installation process.

Prerequisites to ensure a successful deployment:

Make sure that the Microsoft .Net Framework v4.0 or higher is already installed on the

workstation before proceeding.

Windows Installer 4.5 is already installed on the workstation before proceeding.

Remove any previous versions of EDSA Technical/ DesignBase before installing Paladin

DesignBase using unattended installation. Unattended installation will not work if a previous

copy of EDSA Technical/ DesignBase is installed on the workstation.

The installing user account must have local administrator permissions.

It is important that the following properties are included in the Windows Installer command line (Run

dialog box) for proper DesignBase 5.0 client installation:

EDSAPACKAGE – Specifies the DesignBase package purchased (BASIC_500, PREMIUM_500, etc.).

EDSALICENSESERVER – Specifies the server name or IP address where the DesignBase License

Server Service is running. (If this is not specified, Paladin Client License Manager will select local

license.)

If you run an unattended install without the EDSAPACKAGE and EDSALICENSESERVER properties

as part of the command-line, DesignBase will not be licensed. You will then need to run the

Paladin Client License Manager manually on the workstation to configure the license properly.

A general format of the unattended command line is displayed below:

Msiexec.exe<SPACE>/I “< msi file location> :\< installation folder name>\Paladin DesignBase

5.0.msi”<SPACE> ALLUSERS=1<SPACE> INSTALLDIR=”<Directory where you want to save design base

5.0>:\<designbase 5.0 folder>”<SPACE>EDSAPACKAGE=<PACKAGE NAME>

EDSALICENSESERVER=<SERVER NAME><SPACE>/<qb or qn >

Page 34: 001-Complete Install Guide

Complete Installation Guide

33

Once you have gathered all the information about your server name or IP address, package information,

and the location of the DesignBase 5.0 installation files, type in your unattended command-line in the

“Run” dialog box.

Each user will need to run “Rebuild DesignBase Toolbar” from Start>All Programs>Paladin

DesignBase>Rebuild Paladin DesignBase Toolbar, before accessing the DesignBase 5.0

application.

Example 1: To install a workstation with BASIC_500 package with the Paladin License Server running

on a server named “EDSA-loader1”, configured to run unattended with just a progress window (basic user

interface), with your DesignBase installation files located on the X drive (could be any letter c, k…..)

under the DesignBase5 folder, the command-line would look like the following:

Msiexec.exe /I "C:\DesignBase5\Paladin DesignBase 5.0.msi" ALLUSERS=1

INSTALLDIR="E:\DesignBase5" EDSAPACKAGE=BASIC_500 EDSALICENSESERVER=edsa-loader1 /qb

Example 2: To install a workstation with BASIC_500 package with the Paladin License Server running

on a server named “edsa-loader1”, configured to run unattended and silent (no user interface), with your

DesignBase installation files shared by your server on the network under the db folder, the command-line

would be like the following:

Msiexec.exe /I "\\edsa-loader1\Builds\db\Paladin DesignBase 5.0.msi" ALLUSERS=1

INSTALLDIR="C:\DesignBase5" EDSAPACKAGE=BASIC_500 EDSALICENSESERVER=edsa-loader1 /qn

See Windows Help for additional commands for MSIEXEC.EXE

Page 35: 001-Complete Install Guide

Complete Installation Guide

34

DesignBase Permissions

If your environment requires you to use DesignBase permissions on projects, you must run the

DesignBase CreateAdmin.exe utility manually.

Insert the DesignBase CD. Click “Cancel” if the installer starts. From My Computer or Windows

Explorer select the drive that holds the DesignBase CD. Go to the “utilities” folder. You will see a

single executable file. Double click on it to run the Create Admin utility. Once installed, close all

windows.

Page 36: 001-Complete Install Guide

Complete Installation Guide

35

Common Install/Uninstall Issues

1) Error 1919

Solution: Please refer to “Transform_Instructions.docx” under “utilities” folder.

Page 37: 001-Complete Install Guide

Complete Installation Guide

36

2) Actrix.exe System Error.

This error message appears when the chain installation of Actrix fails due to the version of

windows installer.

Solution: Download Windows Installer 4.5 for your operating system at

http://support.microsoft.com/kb/942288. After installing Windows Installer 4.5, restart computer

and then install DesignBase 5.0.

3) DesignBase icons are not functioning correctly across the top of the program as shown in

the screen below.

This can be an indicator of administrator installing the software and a different user logged in

attempting to open the program.

Solution: Rebuild the Toolbar.

a) Exit DesignBase

b) Go to Start >All Programs > Paladin DesignBase > Rebuild Paladin DesignBase Toolbar

Page 38: 001-Complete Install Guide

Complete Installation Guide

37

4) Receiving an error message that DesignBase DLLs are not registered.

If your DLLs are not registered you will get the following message when starting DesignBase 5.0:

Solution: Register DesignBase DLLs and rebuild toolbar.

If you use Windows 7 or Vista:

Go to C:/DesignBase4/Registerdlls.bat, right click and choose “Run as administrator”.

If you use Windows XP:

Just double click those two files mentioned above.

5) License checker failed with the following error messages

This is usually caused by either a temporary license file expiring or the computer was once

configured as a single workstation and the license was converted to a server or vice versa.

Another cause may be improper server installation. The client computer is not able to map to the

server license manager.

Solution: Reconfigure the license manager from the workstation.

Page 39: 001-Complete Install Guide

Complete Installation Guide

38

a. Exit DesignBase

b. From the bottom left corner of your desktop go to:

Start > All Programs > Paladin DesignBase > Licensing > Paladin Client License Manager

c. If you are working from a single workstation, check to see if you have the “Local Host

License” button selected and that your “Paladin.LIC” license file is under the

C:\DesignBase5\Config folder.

d. If the license Package information is missing check if the “Paladin.LIC” license file is under

the C:\DesignBase5\Config folder. If your computer has several Host ID numbers (due to

multiple NIC), you must use the one that you selected when you first installed the software

since the license file was generated based on that Host ID.

e. If you were given a temporary license for a trial version of the software, you must contact

Power Analytics for a permanent license file.

f. If all needed information is correct click on “Close”.

g. Re-open the DesignBase program and Wait 10 seconds while the software builds its toolbars

and register DLLs.

Page 40: 001-Complete Install Guide

Complete Installation Guide

39

h. If you are trying to use one of your server licenses and the problem persists, check the server

license manager “edsalm log file” to verify if the server has stopped running or has crashed.

i. If the license server manager stopped running, click on “Start Server” to restart the server.

j. If server has crashed, manually stop “edsalm.exe” and “lmgrd.exe” processes from Microsoft

task manager before restarting the server. Press Ctrl+Alt+Delete, select “Task Manager” and

the “Processes” tab.

k. If the problem persists, contact Power Analytics support personnel for additional assistance.

Page 41: 001-Complete Install Guide

Complete Installation Guide

40

6) If you are converting from a single workstation to a server license

a. Make sure the “Use License Server” button is selected, the correct package type is in the field

and a server name or IP address is in the correct box.

b. Input all needed information and click “Generate License,” then click “OK”.

c. Re-open the DesignBase program and Wait 10 seconds while the software builds its toolbars

and register DLLs.

7) Actrix error message appears during DesignBase 5.0 installation or when you try opening it

from your desktop icon.

Solution: Manually delete the Actrix folder in the registry editor.

Page 42: 001-Complete Install Guide

Complete Installation Guide

41

Go to Start > Run and type “Regedit” in your Microsoft Run window to open your registry editor

window.

Page 43: 001-Complete Install Guide

Complete Installation Guide

42

a) You may need to delete one or both of the following Actrix folders:

HKEY_CURRENT_USER\Software\Autodesk\Actrix

HKEY_LOCAL_MACHINE\Software\Autodesk\Actrix

8) Getting error Messages when opening DesignBase 5.0, saving Drawing file or closing

DesignBase 5.0.

Solution: Check with your administrator to see if you were granted the rights on the DesignBase

5.0, the Temp, and the Actrix folders on your computer. For more details refer to “Running

DesignBase Products with Standard User Rights on Windows XP, Vista and Windows 7”

beginning on page 52.

Page 44: 001-Complete Install Guide

Complete Installation Guide

43

9) License checkout failed with the following error messages continuously showing up even

though the license file is located correctly. (For Windows 7 and Windows Vista users)

Solution: Go to C:\DesignBase5\Actrix\System, right click on “Actrix.exe” and click “Properties”.

Page 45: 001-Complete Install Guide

Complete Installation Guide

44

Select “Compatibility” tab, check “Run this program as an administrator” and click “OK”.

Page 46: 001-Complete Install Guide

Complete Installation Guide

45

Steps to Turn off UAC in Windows 7(Windows

Vista is slightly different)

1. Click Start, and then click Control Panel.

2. In Control Panel, click User Accounts.

3. In the User Accounts window, click Change User Account Control Settings.

4. Select “Never notify” and click “OK”.

5. Restart Computer.

Important Note! Turning off UAC reduces the security of your computer and may expose you to increased risk from malicious software. We do not recommend leaving UAC disabled.

Page 47: 001-Complete Install Guide

Complete Installation Guide

46

To Uninstall Using Revo Uninstaller

1. Select the previous EDSA Technical/ DesignBase and click “Uninstall”.

Page 48: 001-Complete Install Guide

Complete Installation Guide

47

2. Revo Uninstaller will start the built-in uninstaller of the previous version of EDSA Technical/

DesignBase.

Page 49: 001-Complete Install Guide

Complete Installation Guide

48

3. After the built-in uninstaller finishes the uninstallation, select “Advanced” scanning mode and

click “Scan”.

Page 50: 001-Complete Install Guide

Complete Installation Guide

49

4. Choose “Select All” and then “Delete”. Revo Uninstaller deletes leftover items of the application.

5. Uninstallation is finished.

Page 51: 001-Complete Install Guide

Complete Installation Guide

50

How to determine your permanent LAN Ethernet

Host ID

1. Launch Windows Command Prompt. (Start>All Programs>Accessories>Command Prompt)

2. Type in “ipconfig /all” in the command prompt window and press “Enter.”

Page 52: 001-Complete Install Guide

Complete Installation Guide

51

3. The “Ethernet adapter local Area connection” Host ID or Physical Address (MAC address) will

show in the command prompt.

4. Copy the Ethernet Adapter Local Area Connection, Physical Address (Host ID) to your

clipboard. You will need to send this HOST ID to Power Analytics to generate your DesignBase

License File.

Page 53: 001-Complete Install Guide

Complete Installation Guide

52

Running DesignBase Products with Standard

User Rights on Windows XP, Vista and

Windows 7

Summary

Typically, DesignBase products require the user to run with “Power User” rights on the local machine for

the Microsoft Windows operating systems. This document identifies the required modifications

necessary to allow a user with “Standard User” rights on the local machine to run DesignBase software on

Windows XP, Vista and Windows 7. The modifications described in this document can be performed by

someone with local administrator rights on the local machine. The modifications assume that there hasn’t

been any additional permission or local policy changes other than those that are configured in a default

Windows environment.

Required Registry Changes

The required permissions necessary for the local “Users” group on the following registry hive (and

everything underneath) are shown in Figure 1 below:

Registry Hive: HKEY_LOCAL_MACHINE\SOFTWARE\Autodesk\Actrix

Right click on the Actrix folder present in the registry then click on permission in order to “Access the

permissions for Actrix” window.

Page 54: 001-Complete Install Guide

Complete Installation Guide

53

Figure 1: Permission changes necessary for entire hive.

In 64-bit operating system, Registry Hive:

HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\Autodesk\

Right click on the Autodesk folder present in the registry then click on permission in order to

“Access the permissions for Autodesk” window.

Required File System Changes

The required NTFS permissions necessary for the local “Users” group on the C:\DesignBase5 folder are

shown in Figure 2 below:

Right click on DesignBase5 folder present under your C drive and then click on security and sharing in

order to “DesignBase5 Properties” window.

Page 55: 001-Complete Install Guide

Complete Installation Guide

54

Figure 2: Required permissions on C:\DesignBase5

Page 56: 001-Complete Install Guide

Complete Installation Guide

55

Required File System Changes (cont.)

The required NTFS permissions necessary for the local “Users” group on the temporary folder if it’s been

redirected outside of one’s user profile (e.g. C:\Temp) are shown in Figure 3 below:

Figure 3: Required permissions on C:\Temp

Page 57: 001-Complete Install Guide

Complete Installation Guide

56

Required File System Changes (cont.)

The required NTFS permissions necessary for the local “Users” group on the

C:\Windows\WINEDSA.INI file are shown in Figure 4 below:

Figure 4: Required permissions on C:\Windows\WINEDSA.INI

Important: Make sure to register DesignBase Dlls as an Administrator before switching back to

the standard user account.