001-93701 Owner: GSZ (BDK, MARF, MSMI, GMRL, JMY) Rev *D Tech lead: AKN Build Your USB 3.0 Type-C Cable With CCG2, An ARM Cortex-M0-based Controller Solution

001-93701 Owner: GSZ (BDK, MARF, MSMI, GMRL, JMY) Rev *D Tech lead: AKN

Build Your USB 3.0 Type-C Cable With CCG2, An ARM Cortex-M0-based Controller Solution in a 3.3-mm2 CSP

New Product Introduction:

CCG2: USB Type-C Cable Controller With PD

CCG2 = Type-C Controller Gen2 Type-C = Reversible Slim USB Connector PD = Power Delivery

CCG2: USB Type-C Cable Controller With PD New Product Introduction 1Cover

001-93701 Owner: GSZRev *D Tech Lead: AKN

CCG2: USB Type-C Cable Controller With PD New Product Introduction

USB Type-C – Combines all in one

USB Micro-B

DisplayPort

Power USB Type-B

USB Type-A

4.5 mm

10.4 mm4.0 mm

4.7 mm 1.8 mm

2.4 mm

USB Type-C: Connector of the FutureUSB Type-A and Type-B are the current USB-IF1 standards, but they have limitationsThey use large connectors that prevent slim industrial designs (plug height: A = 4.5 mm; B = 10.4 mm)

They require a fixed plug orientation and a fixed cable direction

They carry only USB signals

Power delivery implementation on them is complicated, expensive and limited to 7.5 W

USB Type-C is the new USB-IF1 standard that solves these problems and enables:Slim industrial design with a 2.4-mm plug height

Reversible plug orientation and cable direction

Transport of both USB signals and PCIe2 or DisplayPort3 signals on the same connector

Easy implementation of low-cost power delivery up to 100 W

USB Type-C is the new, slimmer, all-in-one, 100-W connector

2

1 The USB Implementers Forum creates and maintains USB specifications 3 A display interface standard developed by the Video Electronics Standards2 Peripheral Component Interconnect Express is a standard for the primary bus in PCs Association, used primarily to connect a video source to a display such as a monitor

Market Vision



USB Type-C Cable Controllers: A $140M Market by 2019USB Type-C cable controllers are projected to grow from $5M in 2015 to $20M+ in 2019 at a CAGR of 40%The USB Type-C connector is becoming universal: slimmer, reversible, multiple-protocol and 100-W Power Delivery capable

USB Type-C ports communicate with the cable to determine its power rating and supported protocols

These cables must therefore be electronically marked to report their capabilities

USB Type-C cable controllers address this market with a USB-IF1 certified solution that:Marks cables electronically with a controller IC embedded in the cable plug

Reports cable characteristics, including power rating and supported protocols

Multiplexes USB signals with PCIe2 or DisplayPort3 signals on the same cable

Enables control of signal conditioners in high-speed signal path

Type-C cables, the emerging standard for USB 3.0, require at least one controller in the cable

1 The USB Implementers Forum creates and maintains USB specifications 3 A display interface standard developed by the Video Electronics Standards2 Peripheral Component Interconnect Express is a standard for the primary bus in PCs Association, used primarily to connect a video source to a display such as a monitor

Electronically Marked Type-C Cable A Type-C Cable with a controller on both ends of the cable

3Market Positioning



USB Type-C (Type-C)A new standard with a slimmer and reversible USB plug, a reversible cable, multiple protocol support and 100-W PD

Configuration Channel (CC)USB Type-C bus wire used to carry the PD protocol signals

Dp, DnUSB Type-C bus wires used to transmit and receive USB 2.0 data

TXp, TXn, RXp, RXnUSB Type-C bus wires used to transmit and receive USB 3.0 and PCIe or DisplayPort data

Sideband Use (SBU)The use of a USB Type-C bus wire for non-USB control signals, such as DisplayPort control signals

Type-C TransceiverA transmitter/receiver that communicates over the CC

Electronically Marked Cable Assembly (EMCA)A USB cable with an IC that reports cable characteristics (e.g., current rating) to the Type-C ports

VCONNECTOR (VCONN)USB Type-C bus wire used to power the controller in the EMCA

VBUS

USB Type-C bus wire used for system power; usually 5 V, but increased to 20 V on 100-W USB-PD systems

Terms You Will Hear Today

4

USB 3.0 Type-C Plug

GND RX2p RX2n VBUS Dn CCSBU1 Dp VBUS TX1n TX1p GND

GND TX2p TX2n VBUS SBU2VCONN VBUS RX1n RX1p GND2.4 mm

ToA



USB Power Delivery (USB-PD, PD)A new USB standard that increases power delivery over VBUS from 7.5 W to 100 W

Both hosts and devices can act as either a Provider1 or a Consumer2 of power

For example, a monitor can power a notebook, which in turn can power a tablet or a hard disk drive

The current PD 2.0 standard uses a dedicated CC wire to negotiate the PD logic

Downstream-Facing Port (DFP), Upstream-Facing Port (UFP), Dual-Role Port (DRP)DFP is a USB Type-C port on a host or a hub to which devices are connected

UFP is a USB Type-C port on a device or a hub that connects to a host or a hub DFP

DRP is a USB Type-C port that can operate as either a DFP or a UFP

Peripheral Component Interconnect Express (PCIe)A standard for the primary bus in a PC

DisplayPortA digital display interface standard developed by the Video Electronics Standards Association (VESA)

Used primarily to connect a video source to a display, such as a monitor to a PC

CCG2A Cypress USB Type-C cable controller that complies with the latest USB Type-C and PD standards

Uses Cypress’s proprietary S8 technology with a 32-bit, 48-MHz ARM® Cortex® -M0 processor and 32KB flash

Integrates a single Type-C Transceiver, termination resistors and system-level ESD (8-kV contact, 15-kV air)

Available in a 20-ball, 3.3-mm2 CSP package

Provides a complete, one-chip, hardware and firmware solution for a USB Type-C EMCA

Terms You Will Hear Today

5

1 Provider: A Type-C port that sources power over VBUS2 Consumer: A Type-C port that sinks power from VBUS

ToA



Design Problems Engineers FaceEngineers need a cost-effective USB Type-C cable solutionDedicated controllers for EMCAs do not exist, forcing engineers to consider complex do-it-yourself MCU solutions

MCU-based solutions do not fit inside cable assembliesGeneral-purpose MCUs require additional ICs and passives to implement a Type-C Transceiver

Rapidly evolving USB standards make compliance and interoperability a challengeThe USB Type-C and PD compliance test specifications are continually changing and won’t be finalized until late 2015

Cypress’s CCG2 USB Type-C cable controller solves these problems, providing:A cost-effective, dedicated controller for the USB Type-C EMCA market

A Type-C Transceiver with integrated termination resistors and system-level ESD in a 3.3-mm2 CSP, ideal for cables

An ARM Cortex-M0 with 32KB flash and fully compliant firmware that enables field upgrades as the USB-IF specification changes

Bring your USB Type-C EMCA to market faster with CCG2, a small-footprint, programmable, one-chip USB Type-C cable solution with fully compliant firmware

6Design Problems



CCG2 Is a Cost-Effective Solution

CCG2

VBUS

CC

D+/D-

TX+/TX-, RX+/RX-

GND

VDDD

VDDIO

1μF

1μF

0.1μF 0.1μF

VCONN1 VCONN2

VCCD

CC

VCONN1 VCONN2

Typ

e-C

Plu

g

Typ

e-C

Cab

le

A one-chip USB Type-C cable solution thatRequires only four external capacitors to operate

VSS

2

4

7Cypress Solution

CCG2 Is a Low-BOM, Cost-Effective Solution for USB Type-C EMCA



USB

CCG2 Is Programmable and Upgradable

CCG2 can be upgraded to keep pace with changes in the USB-IF specificationThe on-chip 32KB flash can be programmed anytime, anywhere using its Serial Wire Debug (SWD), I2C or CC pins

CCG2

I2C

MCU

CC

Upgrade.EXE

Click Here

8

Upgrading CCG2 Using SWD

Run PSoC Programmer software on a PC with a MiniProg3 USB dongle to program the CCG2. Typically used during product development.

Use a PC running a firmware upgrade application to program CCG2 in the USB Type-C cable directly. Can be deployed by cable manufacturers to provide upgrades to the end user.

Use an MCU embedded in the USB Type-C cable/accessory or a production tester to program CCG2. Can be used on the production line or in the field.

Upgrading CCG2 Using CC

SWD

Upgrading CCG2 Using I2C

CCG2 CCG2

Cypress Solution

PSoC® Programmer



Feature CYPD2103-20FNXI

(DIY1 Solution)

LPC1102LVUKZ-ND

CPU ARM CM0, 48 MHz ARM CM0, 50 MHz

Flash2, SRAM 32KB, 4KB 32KB, 8KB

Type-C Transceiver Yes No; Needs external components

On-Chip Termination Resistors

Yes No; Needs external components

System-Level ESD ±8-kV Contact, ±15-kV Air No; Needs external components

Serial Interface Two I2C, SPI, UART I2C, SPI, UART

Firmware USB-IF Compliant, field-upgradable Information not available

Supply Voltage 2.7-5.5 V 1.8-3.6 V

Low Power Deep Sleep: 2.5 μA Deep Sleep: 1.6 μA

Package 20-ball, 3.3-mm2 CSP 25-ball, 4.5-mm2 CSP

1 Do it Yourself2 Includes PD firmware

CCG2 Solution vs. Competition’s

9Competitive Comparison



CCG2 Solution Value

Competitor

Type C Controller: NXP LPC1102LVUKPrice: $0.801

BOM Integration

Systems Level ESD: ON Semi CM1230-02CPPrice: $0.101

Opamp: Ti LM339DRPrice: $0.101

Other Components: 7 Resistors, 1 Capacitor, 1 FETPrice: $0.011

Additional Value

USB-IF Compliant PD Protocol Stack: Saves eight man- weeks of engineering effort at $2K per man-week, amortized over 100,000 unitsValue Added: $0.16

Integrated Type-C PHY: Saves four man-weeks of engineering effort at $2K per man-week, amortized over 100,000 unitsValue Added: $0.08

$0.80

$0.10

$0.10

$0.01

$0.21

$0.16

$0.08

$0.24

$1.25

Competitor

Systems Level ESD

Opamp

Other Components

BOM Integration Value

USB-IF Compliant PD Protocol Stack

Integrated Type-C PHY

Total Additional Value

Total Value Delivered

CCG2 Solution Value new:

Total Cost: 20% Total Savings:

CYPD2103-20FNXI$1.001

$0.25

1 Estimated 100ku pricing

10Pricing



USB Type-C Electronically Marked Cable Assembly (EMCA)

Applications

Preliminary Datasheet: Contact Sales

Collateral

Block Diagram

Flash (32KB)

SRAM(4KB)

Serial Wire Debug

Pro

gra

mm

able

I/O

Mat

rix

CCG2: USB Type-C Cable Controller

CORTEX-M0

48 MHz

Integrated Digital Blocks I/O SubsystemMCU Subsystem

Ad

van

ced

Hig

h-P

erfo

rman

ce B

us

(AH

B)

CC5

GPIO6

Port

32-bit MCU Subsystem48-MHz ARM® Cortex® -M0 CPU with 32KB flash and 4KB SRAM to support firmware upgradesIntegrated Digital BlocksIntegrated timers, counters and pulse-width modulatorsTwo SCBs1 configurable to I2C, SPI or UART modesType-C SupportIntegrated transceiver, supporting one Type-C portIntegrated UFP (RD

4) and EMCA (RA5) termination resistors

PD 2.0 SupportStandard power profilesLow-Power OperationTwo independent VCONN rails with integrated isolationIndependent supply voltage pin for GPIO5

2.7-V to 5.5-V operationSleep: 2.0 mA; Deep Sleep: 2.5 µASystem-Level ESD on CC and VDD Pins±8-kV contact, ±15-kV Air Gap IEC61000-4-2 level 4CPackages20-ball, 3.3-mm2 CSP with 0.4-mm ball pitch

Features

1 Serial communication block configurable as UART, SPI or I2C 3 Termination resistor read as a UFP 5 Configuration Channel 2 Timer, counter, pulse-width modulation block 4 Termination resistor read as an EMCA 6 General-purpose input/output

11

Profiles and Configurations

Baseband MAC

Baseband PHY

SCB2

(I2C, SPI, UART)

Integrated RD3, RA

4

VCONN1

VCONN2

VDDIO

Samples: Q1 2015 Production: Q2 2015

Availability

CCG2: USB Type-C Cable Controller

SCB2

(I2C, SPI, UART)

TCPWM1

Product Overview



Getting Started With CCG21. Buy the $49 USB-PD, USB Type-C Demo Kit:

www.cypress.com/CCG2

The kit enables simple, rapid development for USB Type-C EMCA Includes both passive and active EMCA solutions

Provides direct access to all device GPIOs

2. Download the Getting Started with CCG2 App Note (AN94827):www.cypress.com/AN94827

USB-PD, USB Type-C Demo Kit

3.75”

1.75”

12Getting Started



References and LinksProduct datasheet: CCG2 Datasheet

Product roadmap: USB Roadmap

USB-PD, USB Type-C Demo Kit: CCG2 Demo Kit

Product demo video: CCG2 Demo Video

Designing with the USB Type-C Standard workshop: CCG2 Customer Training Workshop

App Note: Getting Started with CCG2 (AN94827)

Knowledge Base Article: CCG2 Knowledge Base

USBIF website: www.usb.org

Visit the CCG2 product webpage for additional details

Print this presentation: CCG2 New Product Introduction

13References and Links


CCG2: USB Type-C Cable Controller with PD New Product Introduction

APPENDIX

14Appendix



USB Portfolio (NDA)U

SB

3.0

US

B 2

.0U

SB

1.1

Device Hub Bridge Host Storage Type-C

CYPD1xxxCCG1

USB Type-C Port Controller2 PD Ports, 5 Profiles, 100 W

Type-C product applies to any

USB speed

1 Simultaneous USB 2.0 andUSB 3.0 traffic on the same port

2 Battery Charging specification v1.2

3 Enables USB charging without host connection

4 Camera Serial Interface v2.0

5 Redundant array of independent disks

6 SD extended capacity

7 Embedded MultiMedia Card8 Display Serial Interface9 UTMI low-pin interface

CY7C68003TX2UL

ULPI9 PHY13, 19.2, 24, 26 MHz

CY7C6801x/53FX2LP

16-Bit Bus to USB 2.08051, 16KB RAM

CYUSB301xFX3

32-Bit Bus to USB 3.0ARM9, 512KB RAM

CY7C64215enCoRe III

M8C MCU, 50 GPIOs, ADCI2C/SPI, 16KB Flash

CY7C643xxenCoRe V

M8C MCU, 36 GPIOs, ADCI2C/SPI, 32KB Flash

CY7C638xxenCoRe™ II

M8C MCU, 20 GPIOsSPI, 8KB Flash

CY7C656x1HX2LP

4 Ports, Industrial Grade1 Transaction Translator

CY7C656x4HX2VL4 Ports

4 Transaction Translators

CYUSB33xxHX3

4 Ports, Shared Link™1

BC 1.22, Ghost Charge™3

CYUSB306xCX3

CSI-24 to USB 3.04 CSI-24 Lanes, 1 Gbps/Lane

CY7C67300EZ-Host

4 Ports, FS USB OTG32 GPIOs

CY7C67200EZ-OTG™

2 Ports, FS USB OTG25 GPIOs

SL811HSFS USB Host/Device

256Byte RAM

CYWB016xBBBay™

HS USB OTGDual SDXC6/eMMC7

CY7C683xxAT2LP

Parallel ATA to USB 2.08051

CY7C6803xNX2LP

NAND Flash to USB 2.08051, 15KB RAM

CYWB0x2xABSArroyo™, Astoria™16-Bit Bus to USB 2.08051, Dual SD/eMMC7

CYUSB303xFX3S™

16-Bit Bus to USB 3.0RAID5, Dual SDXC6/eMMC7

CYUSB302xSD3

SDXC6/eMMC7 to USB 3.0RAID5

DX3 USB 3.0 to DSI8 TX

Contact Sales

CY7C65213USB-to-UART (Gen 2)

3 Mbps, 8 GPIOs

CY7C6521xUSB-Serial

UART/SPI/I2C to USB2 Channels, CapSense®

CY7C64225 USB-to-UART (Gen 1)

230 Kbps

GX3USB 3.0 to Gigabit Ethernet

Contact Sales

CYPD2xxxCCG2

USB Type-C Cable Controller1 PD port, 3.3-mm2 CSP

Q215

Q115

Q414

Q115

Production Development

QQYYQQYYAvailability

Sampling ConceptStatus

15Roadmap

NEW

NEW

NEW

NEW



Get an CCG2 EMCA Demo Kit

How To Get Started

Design ChallengesType-C cables will start converting to EMCA by mid-2015EMCA must support the PD protocolCable solutions must be turnkey for ease of designSolutions must be flexible to keep up with USB-IF standardsA high level of integration is required to reduce the BOMSolutions must be in a package that fits in a cable assembly

CCG2 SolutionSupports Type-C EMCA with an ARM® Cortex®-M0 controllerSupports PD protocol for EMCA with 32KB flashShips with USB-IF certified factory-programmed firmwareSupports field upgrades with free, fully compliant firmwareIntegrates transceiver, termination resistors and system ESDAvailable in a 3.3-mm2 CSP

Cypress Solution Value

CCG2 Solution Example:

Passive EMCA1 With Two CCG2Block Diagram

Datasheet: CCG2 DatasheetApp Note: Getting Started with CCG2Demo Kit: CCG2 EMCA Demo Kit

Suggested Collateral

1 Electronically Marked Cable Assembly without a re-driver 4 The power wire inside a USB cable2 Peripheral Component Interconnect Express is an interface standard for connecting peripherals 5 Configuration Channel3 A display interface standard developed by the Video Electronics Standards 6 USB Type-C bus wire used to power the IC in the EMCA Association used primarily to connect a video source to a display such as a computer monitor

VBUS4

Passive EMCA with CCG2An EMCA that supports the PD protocol. A CCG2 is embedded at each end of the cable and is powered individually by the USB Type-C port at each end.

VCONN6

CC5

2SecureEEPROM I2C

Data Lines (USB SuperSpeed, USB Hi-Speed, PCIe2, DisplayPort3)12

Passive EMCA With One CCG2 Per Cable Plug

CCG2CYPD2103-20FNXI

2 SecureEEPROMI2C

CCG2CYPD2103-20FNXI

VCONN6

GND 2

2

16Solution Example

Typ

e-C

Plu

g

Typ

e-C

Plu

g




How To Get Started


CCG2 SolutionSupports Type-C EMCA with an ARM® Cortex® -M0 controllerSupports PD protocol for EMCA with 32KB flashShips with USB-IF certified factory-programmed firmwareSupports field upgrades with free, fully compliant firmwareIntegrates transceiver, termination resistors and system ESDAvailable in a 3.3-mm2 CSP



Passive EMCA1 With One CCG2



1 Electronically Marked Cable Assembly without a re-driver 4 The power wire inside a USB cable2 Peripheral Component Interconnect Express is an interface standard for connecting peripherals 5 Configuration Channel3 A display interface standard developed by the Video Electronics Standards 6 USB Type-C bus wire used to power the IC in the EMCA Association used primarily to connect a video source to a display such as a computer monitor

17Solution Example

VBUS4

VCONN6 Near

CC5

2SecureEEPROM I2C


Passive EMCA With One CCG2 Per Cable

CCG2CYPD2103-20FNXI

VCONN6 Far

GND 2

2

Typ

e-C

Plu

g

Typ

e-C

Plu

g

Passive EMCA with CCG2A lower-cost implementation of EMCA that supports the PD protocol. A CCG2 is embedded at only one end of the cable and is powered by either USB Type-C port at each end.

Block Diagram




How To Get Started


CCG2 SolutionSupports Type-C EMCA with an ARM® Cortex® -M0 controllerSupports PD protocol for EMCA with 32KB flashShips with USB-IF certified factory-programmed firmwareSupports field upgrades with free, fully compliant firmwareIntegrates transceiver, termination resistors and system ESDAvailable in a 3.3-mm2 CSP




1 Electronically Marked Cable Assembly with a re-driver 4 The power wire inside a USB cable2 Peripheral Component Interconnect Express is an interface standard for connecting peripherals 5 Configuration Channel3 A display interface standard developed by the Video Electronics Standards 6 USB Type-C bus wire used to power the IC in the EMCA Association used primarily to connect a video source to a display such as a computer monitor

VBUS4

VCONN6 Near

CC5

2SecureEEPROM


Active EMCA

CCG2CYPD2105-20FNXI

GND 2

2

Re-driver

12

2

VCONN6 Far

I2C GPIOs

18Solution Example


Active EMCA1

Active EMCA with CCG2An EMCA that includes an embedded re-driver to extend the cable length.

Block Diagram

Typ

e-C

Plu

g

Typ

e-C

Cab

le




How To Get Started

Design ChallengesType-C cables will start converting to EMCA1 by mid-2015EMCA1 must support the PD protocolCable solutions must be turnkey for ease of designSolutions must be flexible to keep up with USB-IF standardsA high level of integration is required to reduce the BOMSolutions must be in a package that fits in a cable assembly

CCG2 SolutionSupports Type-C EMCA1 with an ARM® Cortex® -M0 controllerSupports PD protocol for EMCA1 with the 32KB flashShips with USB-IF certified factory-programmed firmwareSupports field upgrades with free, fully compliant firmwareIntegrates transceiver, termination resistors and system ESDAvailable in a 3.3-mm2 CSP



USB Type-C HDMI Dongle SolutionBlock Diagram

19



1 Electronically Marked Cable Assembly 4 High Definition Multimedia Interface2 Peripheral Component Interconnect Express is an interface standard for connecting peripherals 5 Configuration Channel3 A display interface standard developed by the Video Electronics Standards 6 USB Type-C bus wire used to power the IC in the EMCA Association used primarily to connect a video source to a display such as a computer monitor

USB Type-C HDMI DongleA notebook PC accessory that converts a USB Type-C port to an HDMI output to connect a monitor.

VCONN6

CC5

2SecureEEPROM

I2C

Data Lines (USB SuperSpeed, USB Hi-Speed, DisplayPort3)12

CCG2CYPD2104-20FNXI

GND 2

USBDevice

Controller

2

GPIOs

DisplayPortto HMDI4

Bridge

Solution Example

Typ

e-C

Plu

g

HD

MI

Plu

g2

I2C

2USB Hi-Speed

10

HDMI

8

USB Type-C HDMI Dongle



CCG2 Product Selector Guide

Part Number ApplicationType-C Ports OCP OVP

Termination Resistor Role Package

CYPD2103-20FNXI Passive EMCA1 1 No No RA4 Cable 20-CSP

CYPD2105-20FNXI Active EMCA2 1 No No RA4 Cable 20-CSP

CYPD2104-20FNXI Accessory3 1 No No Rd5 Cable 20-CSP

1 Electronically Marked Cable Assembly without a re-driver 4 Termination resistor denoting an EMCA 2 Electronically Marked Cable Assembly with a re-driver 5 Termination resistor denoting a UFP or Accessory 3 A dongle for bridging Type-C to Type-A, Type-B, Display Port, HDMI or Thunderbolt

Part Numbering Decoder

Number of pins in the package

Feature: Unique combination of OCP, OVP(0 = No, No; 1 = Yes, No; 2 = No, Yes; 3 = Yes, Yes)

Number of Type-C ports: 1 = 1 Port, 2 = 2 PortProduct Type: 1 = First generation, 2 = Second generation

Marketing Code: PD = Power Delivery product family

Company ID: CY = Cypress

Package Type: LQ = QFN, FN = CSP, PV = SSOP

Lead: X = Lead-free

Temperature Range: I = IndustrialCY PD X X X X XX XX X I-

System Use: Unique combination of role and termination4,5

20Product Selector Guide

Documents

001-93701 Owner: GSZ (BDK, MARF, MSMI, GMRL, JMY) Rev *D Tech lead: AKN Build Your USB 3.0 Type-C Cable With CCG2, An ARM Cortex-M0-based Controller Solution