Upload
tastaman123
View
214
Download
0
Embed Size (px)
Citation preview
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 1/37
SOLDERING
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 2/37
DEFINITION
Soldering involves joining two
components of metal with an
intermediate metal whose meltingtemperature is lower than the parent
metal.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 3/37
REQUIREMENTS OF A
SOLDER
Fuse safely below the sag or creep
temperature of the parent alloy.
Resist tarnish and corrosion. Non pitting.
Free flowing.
Match the color of the parent metal.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 4/37
COMPOSITION OF SOLDERS
Gold
Silver
Copper
Tin
Zinc
Gold solders are designated by
fineness.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 5/37
SOLDERING FLUX
Flux means flow.
Improve the flow of a metal
Chemicals that limit the flow of metalsare called antifluxes
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 6/37
FUNCTIONS OF A FLUX
PROTECTOR
It covers the metal surface and prevents oxide
formation.
REDUCER
It helps to reduce the oxides present on the
metal surface.
SOLVENTSIt dissolves any oxide presence and removes it.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 7/37
COMPOSITION OF A FLUX
Borax glass
Boric acid
Silica
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 8/37
ANTIFLUX
Used to control the flow of the metal.
Most common anti-fluxes used is
graphite.Better fluxes like Rouge in chloroform
can be used.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 9/37
SOLDERING
INVESTMENT
This are silica –bonded investments
that fused quartz.
Fused quartz is used because it is thelowest thermally expanding form of
silica.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 10/37
SOLDERING FOR METAL
CERAMIC RESTORATION
It is usually done prior to ceramic
application hence it is also known as
pre ceramic soldering . Post ceramic materials are also
available.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 11/37
Pre ceramic soldering is done at a
temperature of 1075 to 1120 degree
celsius whereas post ceramic solderingshould be done at a temperature of
920 degree celsius because ceramic
may begin to sag at highertemperatures.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 12/37
Post ceramic soldering should be done
after ceramic firing.
Ceramic portions should be finishedonly afetr soldering.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 13/37
ADVANTAGES OF PRE
CERAMIC SOLDERING
The metal framework can be soldered
and tried in prior to ceramic build up.
Minor casting errors can also bepatched up during ceramic build up.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 14/37
DISADVANTAGES OF PRE
CERAMIC SOLDERING
Difficult to build ceramic on
already soldered units.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 15/37
ADVANTAGES OF POST
CERAMIC SOLDERING
Porcelain can be properly build up
due to better access.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 16/37
DISADVANTAGES OF POST
CERAMIC SOLDERING
The metal and porcelain may sag at high
soldering temperatures.
It is more technique sensitive.
The solder should be re-glazed and re-fired.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 17/37
OVEN SOLDERING
Performed under vacuum or air.
A piece of solder is placed in the joint
space and it is heated to a standard
temperature in the furnace.
Superior joint strength.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 18/37
DISADVANTAGES
The parent metal will sag or melt
if heated for o long time.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 19/37
TORCH SOLDERING
Soldering is done under direct flame.
A gas air torch is used for this purpose.
The torch flame has two parts – the
reducing part (is at a higher
temperature) and the soft brush part.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 20/37
The solder should be melted using the softbrush flame.
The flame should be constantly swipedover the solder for a period of 4 -5minutes.
At no point of time the flame should beheld in a stationary position.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 21/37
INFRARED SOLDERING
Used for low fusing connectors.
Good accuracy.
Similar strength as conventional
soldering.
Protective eyewear is necessary.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 22/37
LASER WELDING
Done to join Ti components of dentalcrowns, bridges and partial denture frame
works. Pulsed high power Neodymium lasers are
used.
Low thermal influence preferred in
dentistry.
Superior joint strength.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 23/37
SOLDERING TECHNIQUE
The design of the connector is
determined while fabricating the wax
pattern.
All the solder connectors require about
0.25mm parallel spaced between the
parent components.
The smaller units are inserted
separately in the mouth.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 24/37
A thick mix of quick setting plaster is
molded over the inserted units.
Once the plaster sets, it is removed
along with the inserted units.
Plaster index is inverted.
Components of the prosthesis will be
visible.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 25/37
A triangular piece of utility wax should
be placed to index restoration inorder
to shape the soldering assembly.
The units are invested and the
investment is allowed to bench set.
Invested wax is eliminated using
boiling water or chloroform.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 26/37
Area of the restoration surrounding the
joint should be coated with anti-flux.
After coating the flux and the anti-flux,
the assembly is preheated in a burnout
furnace.
Connectors are soldered using a torch
or a furnace.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 27/37
DISADVANTAGES
Not economical.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 28/37
CERAMIC/ACRYLIC
VENEERING
• The ceramic or acrylic veneers in metal
resin or metal ceramic restorations are
usually added after soldering.
• Ceramic veneering is done in 3 steps
1. METAL PREPARATION.
2. PORCELAIN APPLICATION.
3. PORCELAIN FIRING.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 29/37
METAL PREPARATION
•Any minor casting defects in the cut back
area should be corrected.
•Recovery includes sand-blasting andultrasonic cleaning.
•The gingival surface of the pontic should be
reduced.
•Gingival surface of the pontic should always
be covered with porcelain.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 30/37
PORCELAIN APPLICATION
After preparing the metal, an opaquelayer of porcelain should be applied over
the metal surface. Gingival surface of porcelain is coated
with cervical porcelain.
Layer of cervical, body and incisal
porcelains should be used to build up thefacial surface.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 31/37
Porcelain in the interdental area should
be sectioned to demarcate junction of
the two units.
A separating liquid is applied over the
edentulous ridge prior to building up the
gingival surface of the pontic.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 32/37
PORCELAIN FIRING
•Next the porcelain is fired as per the
manufacture’s instruction.
•After firing the core porcelain, glazeporcelain is added and fired as usual.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 33/37
ACRYLIC VENEERS
•Similar to ceramic veneering except for
a few differences.
•Major difference is that onlymechanical bonding exists between
the metal and resin.
•Bond strength is considerably less.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 34/37
PROCEDURE
• Mechanical undercuts can be created bysprinkling plastic retentive pearls over the
wax pattern before casting.
• The surface of the cast metal can beroughened using Al2O3 air abrasive unit.
• A small quantity opaque resin is added onto
the metal surface. Body shade resin isadded over the opaque resin and contouredusing a modelling instrument.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 35/37
•The resin should be polymerised under
pressure in a warm water bath. Light
cure resins are also available.
•Resin core should be carved to remove
excess material. Space should be
provided to accommodate incisalshade resin.
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 36/37
•Finally incisal shade resin is added and
contoured.
•After polymerization, the restoration isfinished and polished
7/28/2019 00. Soldering
http://slidepdf.com/reader/full/00-soldering 37/37
THANKING YOU