Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
PROGRAMMING INSTRUCTIONS FOR EL SERIES MOTORS
PROGRAMMINGThe 6 & 16 channel remote comes with the feature of being able to choose the number of channels you wish touse. If you are using an AC123 single channel or 2 channel remote, proceed to STEP 1: PAIRING A REMOTE
STEP 1 CHOOSING THE NUMBER OF CHANNELS
31
Press the channel selection buttonuntil the desired amount of channelsis reached.
Press and hold the stop button andchannel selection button until thechannel light flashes.
2
ADDING OR DELETING CHANNELS
Press and hold the stop button and the channel selection button untilthe channel light flashes.
Press and hold the selection button and the stop button until the channel light flashes.
The extra channel is now added.
STEP 2
2 3
Press the channel selection button until the desired amount of channelsis reached.
1
PLEASE CALL: +61 2 9620 4866 to speak with a qualified technician should you experience any problems. Please call while on site so that the problem can be solved over the phone and to avoid revisiting a job.
Intro EL Series Motorisation Page 1
SERIESEL
HAND HELD REMOTE
ChannelSelection Buttons
Selection Buttons
StopButton
The correct amount of channels onthe remote should now beoperational.
ChannelDisplay
Selection Buttons
StopButton
Selection Buttons
StopButtonSelection
Buttons
NOTE: All motors previously programmed to the remote will remain the same.
PROGRAMMING INSTRUCTIONS FOR EL SERIES MOTORS
PROGRAMMING
STEP 2 PAIRING A REMOTE TO A BLIND
31
Is the blind travelling in the correctdirection when you press the up or down button on the remote?
Press and hold the stop button on the remote until the motor jogs.
2
PLEASE CALL: +61 2 9620 4866 to speak with a qualified technician should you experience any problems. Please call while on site so that the problem can be solved over the phone and to avoid revisiting a job.
Intro EL Series Motorisation Page 2
SERIESEL
Within 5 seconds, press the down button on the remote until the motor jogs.
STEP 1 PAIRING A REMOTE TO A BLIND
Press the or on the motor head until the motor jogs.
2 3
Within 5 seconds from Step 3, press the up button on the remote until the motor jogs.
41
Connect the motor to a power supply.
Select the channel on the remote that you want the blind paired with.
Now the remote ispaired to the motor.
UpButton
ChannelSelectionButtons
YES
NO
The blind is now travelling in the correct direction. Move onto Step 3: Limit Settings
or
StopButton Down
Button
STEP 3 LIMIT SETTING INSTRUCTIONS: Setting the TOP Limit
Press the up buttonon the remote to movethe blind to the exactposition you want thetop limit.
2 3
Press the setting button on the remote until the motor jogs.
4
Press the setting buttonon the remote until themotor jogs.
Top limit is now set.Go to Step 4 - Bottom Limit
UpButton
Start with the blind 30cm down from the desired top limit.
NOTE: Both TOP and BOTTOM limits must be set before any intermediate limits can be set. See Troubleshoot if out come is not achieved.
1
30cm
SettingButton
SettingButton
STEP 5 ADDING EXTRA LIMITS (Optional)
31
Move the blind towards the exact3rd limit position.
Press the setting button on theremote until the motor jogs.
2
PLEASE CALL: +61 2 9620 4866 to speak with a qualified technician should you experience any problems. Please call while on site so that the problem can be solved over the phone and to avoid revisiting a job.
Intro EL Series Motorisation Page 3
Push the setting button a secondtime until the motor jogs to exit limit setting mode. The 3rd limit is set.
STEP 4 LIMIT SETTING INSTRUCTIONS: Setting the BOTTOM Limit
Press the setting button a second time until themotor jogs to exit limitsetting mode.
2 3 4
Press the setting buttonon the remote until themotor jogs.
Bottom limit is now set?
Move the blind downto the desired bottomlimit.
NOTE: Both TOP and BOTTOM limits must be set before any intermediate limits can be set. See Troubleshoot if out come is not achieved.
SettingButton
SettingButton YES
NO
The blind is now fully programmed.
Go to the Troubleshootsection of these instructions.
1
SettingButton
SettingButton
STEP 6 EDIT A LIMIT SETTING
Move the blind to the new position where you would like the newlimit to be.
2
Press the setting button on the remote until the motor jogs.
4
Press the setting buttonon the remote until themotor jogs.
Top limit has now been changed.
Operate the blind to thelimit that needs to bechanged.
SettingButton
SettingButton
1 3
STEP 7 DELETING A LIMIT SETTING
2 3Press and hold the settingbutton on the back of theremote for 8 seconds. Themotor will jog once, thenjog a second time after7 seconds.
The motor’s limitis now deleted.
Operate the blind to the limit that needs to be deleted.
SettingButton
1NOTE: The first limit that was set cannot be deleted, unless the motor is put back into factory mode. See Troubleshoot.
STEP 8 PUTTING THE BLIND INTO AND OUT OF JOG MODE (Optional)
31
Press and hold the stop button onthe remote until the motor jogs.
Within 5 seconds, release, and pressthe stop button until the motor jogs.
2
PLEASE CALL: +61 2 9620 4866 to speak with a qualified technician should you experience any problems. Please call while on site so that the problem can be solved over the phone and to avoid revisiting a job.
Intro EL Series Motorisation Page 4
STEP 10 COPY MOTOR(S) FROM ONE REMOTE TO ANOTHER
1
StopButton
StopButton
You are now in orout of jog mode.
NOStart Step 8 from the
very beginning atPoint 1.
NOTE: Jog mode allows the blind to move in very small increments for precise limit settings if required.
STEP 9 PROGRAMMING A FAVOURITES CHANNEL
Select the channel chosento be the FAVOURITESchannel.
2 3 4
Press and hold the stopbutton on the remoteuntil the motor jogs.
Select the channel thatthe desired motor hasbeen programmed to.
1
Press the up button onthe remote until themotor jogs.
UpButton
ChannelSelectionButtons
ChannelSelectionButtons
StopButton
5 Repeat Steps 1 to 4 until all desired motors have been copied to their FAVOURITES channel.
2 3 4
Select the channel tocopy on the originalremote.
StopButton
Push the stop button untilthe motor jogs.
UpButton
On the new remote push the up button until the motor jogs.
Repeat Steps 1 to 3until the requiredmotors are copiedto the extra remote.
TROUBLESHOOT : To Clear The Settings
31
Press the or on the motor head for 8 seconds. The motor will jog once, then double jog after another 7 seconds.
2NOTE: If the motor has not been programmed successfully, clear all settings and go back to the start.
Press up or down on the remote,is there a response from themotor?
Up or DownButton
YES
NO
Go back to Point 1 of Troubleshoot
Go back to the start (Step 1) of these programming instructionsand start over again.