Crispin · and Vacuum Valve, Crispin Pressure Air Valve or Crispin Midget Air Valve literature. All Crispin Valves are hydrostatically tested to 150% of their maximum working pressure

Crispin Multiplex Manufacturing Co. • 600 Fowler Avenue • Berwick, PA 18603 • 1-800-247-VALVT: (570) 752-4524 • F: (570) 752-4962 • www.crispinvalve.com • [email protected]

Since 1905

The C & AL/PL SeriesCombination & Dual Air ValvesOffering Single Unit Integrity When Both Air & Vacuumand Pressure Valves Are Required On An Installation

Crispin

C SER

IES

Size of Valve 1/2” 1” 2” 3” 4” 6” 8” 10”

Model No. C5 C10 C20 C30 C40Screwed Inlet

125# C21 C31 C41 C61 C81 C101Flanged Inlet

250# C22 C32 C42 C62 C82 C102Flanged Inlet

• Single unit integritywhen both Air &Vacuum and Pressure Valves arerequired at onepoint on a pipeline

• Meets AWWA C-512

Valve Function The Crispin Combination Air Valve is a combination of an Air

and Vacuum Unit and a Pressure Unit, designed with singleunit integrity when both types of valves are required at one

point. The air and vacuum unit operates the same as the standardair and vacuum valve. It releases a large quantity of air during thefilling of the pipeline, and also permits a large quantity of air toreenter the pipeline to break the vacuum and eliminate any dangerof collapse should the liquid suddenly leave the pipeline. The pres-sure unit operates independently and releases small accumulationsof air which may collect while the line is in operation and underpressure. For further operating information, refer to Crispin Airand Vacuum Valve, Crispin Pressure Air Valve or Crispin MidgetAir Valve literature.All Crispin Valves are hydrostatically tested to 150% of their maximum working pressure. Forpressures above 300 PSIG, steel, stainless steel or ductile iron may be used.

Combination Air Valves

“C” Series Combination Air Valves

Dimensions and Weights

Model Information

Please Refer to Air & Vacuum and Pressure Air

Release Valve for Parts Lists.

Size of Valve 1/2” 1” 2” 3” 4” 6” 8” 10”

Width 5” 6 1/4” 9 7/8” 11 1/2” 14” 15” 17 3/4” 21”Length 8 3/4” 10 1/4” 15 5/8” 20” 22 1/8” 23” 25 5/8” 29”Height Scwd. Connection 5 5/8” 6” 9 5/8” 13 1/2” 15 1/8” — — —Height Flgd. Connection — — 13 1/4” 17 1/2” 18” 16” 18 1/8” 22 1/8”Weight Scwd. Connection 13lbs 21lbs 68lbs 120lbs 179lbs — — —Weight Flgd. Connection — — 73lbs 140lbs 195lbs 198lbs 290lbs 525lbsPressure Unit Size Midget Midget 1” 1” 1” 1” 1” 1”Pressure Unit 3/8” 3/8” 1/2” 1/2” 1/2” 1/2” 1/2” 1/2” Outlet Connection NPT NPT NPT NPT NPT NPT NPT NPTAir &Vacuum Unit Size 1/2” 1” 2” 3” 4” 6” 8” 10”Air & Vacuum Unit Outlet 1/2” 1” 2” 3” 4” 6” 8” 10” Connection NPT NPT NPT NPT NPT NPT NPT NPT

Crispin Valve, 600 Fowler Ave., Berwick, PA 18603 • 1-800-AIR-VALV • T: (570) 752-4524 • F: (570) 752-4962 • WWW.CRISPINVALVE.COM • [email protected]

For sizes above 10”, please contact the factory.2

CCrispin Valve, 600 Fowler Ave., Berwick, PA 18603 • 1-800-AIR-VALV • T: (570) 752-4524 • F: (570) 752-4962 • WWW.CRISPINVALVE.COM • [email protected]

Submittal Sheet for Crispin C Series

SUBMITTA

L SHEET FO

R C SER

IES1/2”–1” Combo. Air Release (1 of 2)Manufactured in compliance with ANSI/AWWA C512 Date: 2016

3

A

29

65

11

12

155

24

798

A

4

11

1013

1 5 9

728A

B

3

Specifications

The combination air valve(s) shall be installed at high points in the system or at points selected by the engineer. This will permitdischarging the surge of air from an empty line when filling and relieve the vacuum when draining, and also to release an accu-mulation of air when the system is under pressure.

The body of the valve shall be one integral casting or 2 valve bodies flange bolted together containing an air and vacuum valveand a separate pressure valve mechanism.

The Air and Vacuum Valve shall operate by sealing the BUNA-N rubber outlet seat with a peripherially guided float as the liquidenters the valve chamber to raise the float. All Crispin Valves are hydrostatically tested at 150% of their maximum working pres-sure.

The pressure air release valve shall operate through simple or compound levers to permit air to be released under operating con-ditions. The valve shall have a ______________” orifice with valve sealing faces of an adjustable BUNA-N valve and (stainlesssteel or PVC) and shall operate at ____________ PSIG and be capable of passing ___________ SCFM of air.

The valve(s) shall be CRISPIN Model ____________ Combination Air Valve, Type N, (PVC seat and BUNA-N rubber valve) orType P (stainless steel seat and BUNA-N rubber valve) pressure valve as manufactured by Crispin-Multiplex Manufacturing Co.,Berwick, Pa.

The valve(s) shall be _____________” NPT screwed or ANSI Class (125,250) flanged inlet connection and shall be cast iron body,top, and inlet flange (where required), stainless steel floats with bronze and brass or stainless steel trim. Refer to Air & Vacuumand Pressure Air Release specifications for Valve description.

Option: A protectop shall be supplied to prevent debris from entering the outlet of the Air and Vacuum Valve.

Option: (Where pressures are greater than 300 psig), the valve(s) shall be ANSI Class flanged inlet connection and shall have a(steel, stainless steel, or ductile iron) body, top and inlet flange.

Standard operating pressure for Crispin Air Valves is 20 to 150 PSIG. Please check one of the following if your operating needsdiffer:____ 2 to 40 PSIG ____ 151 to 300 PSIG

ITEM DESCRIPTION MATERIAL ASTM1S TOP CAST IRON A126 CL.B2 FLANGE CAST IRON A126 CL.B3 BODY CAST IRON A126 CL.B4 GASKET ARMSTRONG N-8092 N/A5 SEAT BUNA-N RUBBER D20006S FLOAT STAINLESS STEEL A2407 HANGER STAINLESS STEEL A2408 CUP STAINLESS STEEL A3129 RIVET STAINLESS STEEL A5829A FLOAT ROD STAINLESS STEEL A58211 BOLT STEEL A30712 NUT STEEL A56329 PLUG BRASS B50550 INTERFERENCE PIN STAINLESS STEEL A582

ITEM DESCRIPTION MATERIAL ASTM1 VALVE SEAT STAINLESS STEEL A2402 PLUNGER BUTTON VITON D20004 VALVE LEVER STAINLESS STEEL A2405 SCREW (DRIVE) STAINLESS STEEL A1936 BALL FLOAT STAINLESS STEEL A2407 HINGE PIN STAINLESS STEEL A5808 HINGE BUTT STAINLESS STEEL A2409 BOLT STEEL A30710 SCREW STAINLESS STEEL A19311 FLANGE CAST IRON A126 CL.B13 FLANGE GASKET ARMSTRONG N-8092 N/A



SUBMITTA

L SH

EET FO

R C SER

IES

1/2”–1” Combo. Air Release (2 of 2)Manufactured in compliance with ANSI/AWWA C512 Date: 2016

Orifice OptionsDIAMETER MAX. PRES. DISCHARGE RATE

1/8” 50 PSIG 9.6 SCFM3/32” 85 PSIG 8.3 SCFM1/16” 150 PSIG 6.1 SCFM3/64” 200 PSIG 4.5 SCFM1/32” 300 PSIG 3.2 SCFM

Air & Vacuum Valve Parts List

Size SpecificationsMODEL INLET SIZE OUTLET SIZE A B WHT.C5 1/2” NPT 1/2” NPT 8.75 5.75 13C10 1” NPT 1” NPT 10.25 6.00 21

4

Pressure Air Release Parts List

Crispin Valve, 600 Fowler Ave., Berwick, PA 18603 • 1-800-AIR-VALV • T: (570) 752-4524 • F: (570) 752-4962 • WWW.CRISPINVALVE.COM • [email protected] C


SUBMITTA

L SHEET FO

R C SER

IES2” Combination Air Release Valve

Manufactured in compliance with ANSI/AWWA C512 Date: 2016

Specifications

ITEM DESCRIPTION MATERIAL ASTM1S TOP CAST IRON A126 CL.B2 FLANGE CAST IRON A126 CL.B3 BODY CAST IRON A126 CL.B4 GASKET ARMSTRONG N—8092 N/A5 SEAT BUNA—N RUBBER D20006S FLOAT STAI N LESS STEEL A2407 HANGER STAINLESS STEEL A2408 CUP STAINLESS STEEL A2409 RIVET STAINLESS STEEL A58211 BOLT STEEL A30712 N UT STEEL A56329 PLUG BRASS B50550 INTERFERENCE PIN STAINLESS STEEL A582

*1 N VALVE SEAT PVC 1784*1 P VALVE SEAT STAINLESS STEEL A5822 VALVE PLUNGER BUNA—N RUBBER D20003 PLUNGER NUT STAINLESS STEEL A5633W LOCK WASHER STAINLESS STEEL A2405 VALVE FULCRUM STAINLESS STEEL A2406 VALVE LEVER STAINLESS STEEL A5827 LlNK STAINLESS STEEL A2408 BALL FULCRUM STAINLESS STEEL A5829 BALL FLOAT STAINLESS STEEL A24010 BALL LEVER STAINLESS STEEL A24011 BEARING PIN STAINLESS STEEL A58212 BEARING PIN STAINLESS STEEL A58213 BEARING PIN STAINLESS STEEL A58215 COTTER PIN STAINLESS STEEL A49317 BOLT STEEL A30718 NUT STEEL A56319 TOP CAST IRON A126 CL.B20 FLANGE CAST IRON A126 CL.B22 FULCRUM WASHER FIBER D71022A FULCRUM WASHER FIBER D71023 SEAT GASKET BUNA—N RUBBER D200024 FLANGE GASKET ARMSTRONG N-8092 N/A25 BOLT STAINLESS STEEL A19329 PLUG BRASS B505

CP1 NIPPLE STEEL A53CP2 COMPANION FLANGE CAST IRON A126 CL.B

* Parts are interchangable and optional at customer’s request

Orifice OptionsDIAMETER MAX. PRESSURE DISCHARGE RATE

5/16 100 PSIG 105 SCFM1/4 150 PSIG 98 SCFM3/16 200 PSIG 72 SCFM5/32 250 PSIG 61.1 SCFM1/8 300 PSIG 46.7 SCFM

PARTS LIST FOR AIR & VACUUM Size SpecificationsMODEL INLET SIZE OUTLET SIZE A B C WHT.C20 2” NPT 2” NPT 15.75 9.50 64** C21 2” 125” FLG 2” NPT 15.75 13.25 70**C22 2” 250# FLG 2” NPT 15.75 14.00 72**Includes ANSI CL. 125 or 250 Companion FLG. & NPL.

The combination air valve(s) shall be installed at high points in the system orat points selected by the engineer. This will permit discharging the surge of airfrom an empty line when filling and relieve the vacuum when draining, and alsoto release accumulated air when the system is under pressure. The valve bodyshall be one integral casting or 2 valve bodies flange bolted together contain-ing an air and vacuum valve and a separate pressure valve mechanism.The Air and Vacuum Valve shall operate by sealing the BUNA-N rubber outletseat with a peripherially guided float as the liquid enters the valve chamber toraise the float. All Crispin Valves are hydrostatically tested to 150% of theirmaximum working pressure.The pressure air release valve shall operate through simple or compoundlevers to permit air to be released under operating conditions. The valve shallhave a ___________” orifice with valve sealing faces of an adjustable BUNA-N valve and (stainless steel or PVC) and shall operate at _________ PSIG andbe capable of passing ________ SCFM of air.The valve(s) shall be CRISPIN Model ____________ Combination Air Valve,Type N, (PVC seat and BUNA-N rubber valve) or Type P (stainless steel seatand BUNA-N rubber valve) pressure valve as manufactured by Crispin-Multi-plex Manufacturing Co., Berwick, Pa.The valve(s) shall be _____________” NPT screwed or ANSI Class (125,250)flanged inlet connection and shall be cast iron body, top, and inlet flange(where required), stainless steel floats with bronze and brass or stainless steeltrim. Refer to Air & Vacuum and Pressure Air Release specifications for Valvedescription.Option: A protectop shall be supplied to prevent debris from entering the out-let of the Air and Vacuum Valve.Option: (Where pressures are greater than 300 psig), the valve(s) shall beANSI Class flanged inlet connection and shall have a (steel, stainless steel, orductile iron) body, top and inlet flange.

Standard operating pressure for Crispin Air Valves is 20 to 150 PSIG.Please check one of the following if your operating needs differ:____ 2 to 40 PSIG ____ 151 to 300 PSIG

A

9

3

4

22A

1N-1P

2420

22 181925

23 18 2217

188

9

13111513

5

7S

6S

CP1

CP2

50 1P 11

12

BC

A

A

PARTS LIST FOR PRESSURE UNIT

PARTS LIST FOR FLANGE CONNECTION

5



SUBMITTA

L SH

EET FO

R C SER

IES

3”–4” Combo. Air Release (1 of 2)Manufactured in compliance with ANSI/AWWA C512 Date: 2016

SpecificationsThe combination air valve(s) shall be installed at high points in the system or at points selected by the engineer. This will permit discharging thesurge of air from an empty line when filling and relieve the vacuum when draining, and also to release an accumulation of air when the systemis under pressure.

The body of the valve shall be one integral casting or 2 valve bodies flange bolted together containing an air and vacuum valve and a separatepressure valve mechanism.

The Air and Vacuum Valve shall operate by sealing the BUNA-N rubber outlet seat with a peripherially guided float as the liquid enters the valve cham-ber to raise the float. All Crispin Valves are hydrostatically tested at 150% of their maximum working pressure.

The pressure air release valve shall operate through simple or compound levers to permit air to be released under operating conditions. The valveshall have a ______________” orifice with valve sealing faces of an adjustable BUNA-N valve (stainless steel or PVC) and shall operate at_____________ PSIG and be capable of passing ___________ SCFM of air.

The valve(s) shall be CRISPIN Model ____________ Combination Air Valve, Type N, (PVC seat and BUNA-N rubber valve) or Type P (stainlesssteel seat and BUNA-N rubber valve) pressure valve as manufactured by Crispin-Multiplex Manufacturing Co., Berwick, Pa.

The valve(s) shall be _____________” NPT screwed or ANSI Class (125,250) flanged inlet connection and shall be cast iron body, top, and inletflange (where required), stainless steel floats with bronze and brass or stainless steel trim. Refer to Air & Vacuum and Pressure Air Release spec-ifications for Valve description.


Option: (Where pressures are greater than 300 psig), the valve(s) shall be ANSI Class flanged inlet connection and shall have a (steel, stainlesssteel, or ductile iron) body, top and inlet flange.

Standard operating pressure for Crispin Air Valves is 20 to 150 PSIG. Please check one of the following if your operating needs differ:____ 2 to 40 PSIG ____ 151 to 300 PSIG



21

1N-1P

22A

24

20 2218

192523 18 8 22 17

18

9

SECTION A–A-

1311

1510

13

CB

A-

A-A

3029

6S

2 29

1S

50 11

1231

4

5

3FH

6



SUBMITTA

L SHEET FO

R C SER

IES3”–4” Combo. Air Release (2 of 2)


ITEM DESCRIPTION MATERIAL ASTM1S TOP CAST IRON A126 CL.B2 FLANGE CAST IRON A126 CL.B3FH BODY CAST IRON A126 CL.B4 GASKET ARMSTRONG N—8092 N/A5 SEAT BUNA—N RUBBER D20006S FLOAT STAINLESS STEEL A24011 BOLT STEEL A30712 NUT STEEL A56329 PLUG BRASS B50550 INTERFERENCE PIN STAINLESS STEEL A582

*1N VALVE SEAT PVC 1784*1P VALVE SEAT STAINLESS STEEL A5822 VALVE PLUNGER BUNA—N RUBBER D20003 PLUNGER NUT STAINLESS STEEL A5633W LOCK WASHER STAINLESS STEEL A2405 VALVE FULCRUM STAINLESS STEEL A2406 VALVE LEVER STAINLESS STEEL A5827 LlNK STAIN LESS STEEL A2408 BALL FULCRUM STAINLESS STEEL A5829 BALL FLOAT STAINLESS STEEL A24010 BALL LEVER STAINLESS STEEL A24011 BEARING PIN STAINLESS STEEL A58212 BEARING PIN STAINLESS STEEL A58213 BEARING PIN STAINLESS STEEL A58215 COTTER PIN STAINLESS STEEL A49317 BOLT STEEL A30718 NUT STEEL A56319 TOP CAST IRON A126 CL.B20 FLANGE CAST IRON A126 CL.B21 BODY CAST IRON A126 CL.B22 FULCRUM WASHER FIBER D71022A FULCRUM WASHER FIBER D71023 SEAT GASKET BUNA—N RUBBER D200024 FLANGE GASKET ARMSTRONG N-8092 N/A25 BOLT STAINLESS STEEL A19329 PLUG (NOT SHOWN) BRASS B50530 GASKET ARMSTRONG N-8092 N/A31 BOLT STEEL A307

PARTS LIST FOR AIR & VACUUM

SIZE SPECIFICATIONSMODEL INLET SIZE OUTLET SIZE A B C WEIGHTC30 3” NPT 3” NPT 20.00 13.50 120C31 3” 125# FLG 3” NPT 20.00 17.50 140C32 3” 250# FLG 3” NPT 20.00 17.50 148C40 4” NPT 4” NPT 22.25 15.25 182C41 4” 125# FLG 4” NPT 22.25 18.00 198C42 4” 250# FLG 4” NPT 22.25 18.25 209

PARTS LIST FOR AIR RELEASE UNIT

* Parts are interchangeableand optional atcustomer’srequest

7



SUBMITTA

L SH

EET FO

R C SER

IES

6”–10” Combo. Air Release (1 of 2)Manufactured in compliance with ANSI/AWWA C512 Date: 2016

SpecificationsThe combination air valve(s) shall be installed at highpoints in the system or at points selected by the engineer.This will permit discharging the surge of air from an emptyline when filling and relieve the vacuum when draining,and also to release an accumulation of air when the sys-tem is under pressure.

The body of the valve shall be one integral casting or 2valve bodies flange bolted together containing an air and vacuum valve and a separate pressure valve mechanism.

The Air and Vacuum Valve shall operate by sealing the BUNA-N rubber outlet seat with a peripherially guided float as the liquid enters the valvechamber to raise the float. All Crispin valves are hydrostatically tested to 150% of their maximum working pressure.

The pressure air release valve shall operate through simple or compound levers to permit air to be released under operating conditions. The valveshall have a ______________” orifice with valve sealing faces of an adjustable BUNA-N valve and (stainless steel or PVC) and shall operate at_____________ PSIG and be capable of passing ___________ SCFM of air.

The valve(s) shall be CRISPIN Model ____________ Combination Air Valve, Type N, (PVC seat and BUNA-N rubber valve) or Type P (stainlesssteel seat and BUNA-N rubber valve) pressure valve as manufactured by Multiplex Manufacturing Co., Berwick, Pa.

The valve(s) shall be _____________” NPT screwed or ANSI Class (125,250) flanged inlet connection and shall be cast iron body, top, and inletflange (where required), stainless steel floats with bronze and brass or stainless steel trim. Refer to Air & Vacuum and Pressure Air Release spec-ifications for Valve description.


Option: (Where pressures are greater than 300 psig), the valve(s) shall be ANSI Class flanged inlet connection and shall have a (steel, stainlesssteel, or ductile iron) body, top and inlet flange.

Standard operating pressure for Crispin Air Valves is 20 to 150 PSIG. Please check one of the following if your operating needs differ:____ 2 to 40 PSIG ____ 151 to 300 PSIG



SIZE SPECIFICATIONSMODEL INLET SIZE OUTLET SIZE A B WEIGHTC61 6” 125# FLG 6” NPT 23.00 16.00 202C62 6” 250# FLG 6” NPT 23.00 16.25 225C81 8” 125# FLG 8” NPT 25.75 18.25 293C82 8” 250# FLG 8” NPT 25.75 18.75 323C101 10” 125# FLG 10” NPT 29.00 22.25 528C102 10” 250# FLG 10” NPT 29.00 23.00 578

21

1N-1N

22A

24

20 22 18

1925

23 18 822 17

18

9

SECTION A–A-

13111513

B

A-

A

30

29

31

3F

4

2

6

13

1H

1S 1110

12

5

55

8

A-



SUBMITTA

L SHEET FO

R C SER

IES6”–10” Combo. Air Release (2 of 2)


ITEM DESCRIPTION MATERIAL ASTM**1H HOOD HRCQ STEEL N/A1S TOP CAST IRON A126 CL.B2 FLANGE CAST IRON A126 CL.B3F BODY CAST IRON A126 CL.B4 GASKET ARMSTRONG N—8092 N/A5 SEAT BUNA—N RUBBER D20006 FLOAT STAINLESS STEEL A240**10 BOLT STEEL A30711 BOLT STEEL A30712 NUT STEEL A56313 BOLT STEEL A30729 PLUG BRASS B50555 LIFTING LUG STEEL A36

*1N VALVE SEAT PVC 1784*1P VALVE SEAT STAINLESS STEEL A5822 VALVE PLUNGER BUNA—N RUBBER & S/S D20003 PLUNGER NUT STAINLESS STEEL A5633W LOCK WASHER STAINLESS STEEL A2405 VALVE FULCRUM STAINLESS STEEL A2406 VALVE LEVER STAINLESS STEEL A5827 LlNK STAINLESS STEEL A2408 BALL FULCRUM STAINLESS STEEL A5829 BALL FLOAT STAINLESS STEEL A24010 BALL LEVER STAINLESS STEEL A24011 BEARING PIN STAINLESS STEEL A58212 BEARING PIN STAINLESS STEEL A58213 BEARING PIN STAINLESS STEEL A58215 COTTER PIN STAINLESS STEEL A49317 BOLT STEEL A30718 NUT STEEL A56319 TOP CAST IRON A126 CL.B20 FLANGE CAST IRON A126 CL.B21 BODY CAST IRON A126 CL.B22 FULCRUM WASHER FIBER D71022A FULCRUM WASHER FIBER D71023 SEAT GASKET BUNA—N RUBBER D200024 FLANGE GASKET ARMSTRONG N-8092 N/A25 BOLT STAINLESS STEEL A19329 PLUG (NOT SHOWN) BRASS B50530 GASKET ARMSTRONG N-8092 N/A31 BOLT STEEL A307

* Parts are interchangeable and optional at customer’s request** Optional at customer’s request


PARTS LIST FOR AIR RELEASE UNIT

9For sizes above 10”, please contact the factory.

Model Valve Size (C) Height (B) Width (A) WeightAL10/M5 1” 13 1/4” 9 3/4” 24lbsAL20/M5 2” 14 3/4” 12 1/4” 53*AL21/M5 2” 18 1/4” 12 1/4” 59*AL22/M5 2” 18 1/2” 12 1/4” 61AL30/M5 3” 16” 16” 103AL31/M5 3” 19 3/4” 16” 120AL32/M5 3” 20 1/4” 16” 128AL40/PL10 4” 20 1/4” 20” 178AL41/PL10 4” 23 3/4 20” 194AL42/PL10 4” 24 1/4” 20” 205AL61/PL10 6” 22 1/4” 21” 198AL62/PL10 6” 22 1/2” 21” 221AL81/PL10 8” 25 1/2” 24 1/2” 289AL82/PL10 8” 26” 24 1/2” 319AL101/PL10 10” 29” 33 3/4” 524AL102/PL10 10” 29 3/4” 33 3/4” 574AL121/PL20 12” 32 1/2” 34 1/2” 775AL122/PL20 12” 33 1/4” 34 1/2” 828AL141/PL20 14” 34 1/4” 36 1/2” 1023AL142/PL20 14” 35” 36 1/2” 1210AL161/PL20 16” 36 1/2” 39 1/4” 1143AL162/PL20 16” 37 1/2” 39 1/4” 1326

• Single pipeline location when both Air & Vacuum andPressure Valves arerequired at one pointon a pipeline

• Meets AWWA C-512

Valve Function

T he sizing of a Dual or Combination Valve requires the samedata and parameters of the Air & Vacuum Valve and PressureAir Release Valve. Subsequently, if the required pressure

orifice size varies from the standard pressure orifice offered witheach Combination, then a Dual Valve, with its flexibility, can beapplied to accommodate specific orifice requirements.

The flexibility of the Dual Valve allows a wide variety of con-ditions to be addressed. For example: if the system pump capacitywere to dictate the air and vacuum sizing of 2” for air release, thenthat same capacity would normally require a Pressure Air ReleaseValve in the Midget size.

However, if a greater amount of air was expected to beentrained in the liquid, because of siphoning through leaky joints orpacking, or because of turbulence, etc., then a larger Pressure Valvewith a greater orifice size could be provided.

Also, should vacuum relief be the deciding Air and Vacuum sizing parameter, because of pipe slope, size, and/or materials ofconstruction, then the corresponding Universal or CombinationPressure Air Release orifice could be larger than would actually berequired for the system.

In this case, the flexibility of the Dual Valve would accommo-date the system performance requirements.

AL/PL

SER

IES

Dual Air Valves

AL/PL Series Dual Air Valves

Customize Your Air Release Requirements

Please Refer to Air & Vacuum andPressure Air Release Valve for Parts

Lists.

Dimensions and Weights*

Crispin Valve, 600 Fowler Ave., Berwick, PA 18603 • 1-800-AIR-VALV • T: (570) 752-4524 • F: (570) 752-4962 • WWW.CRISPINVALVE.COM • [email protected]/PL

10* Available up through 24”. Please contact factory for sizes 18” and larger.

Crispin Valve, 600 Fowler Ave., Berwick, PA 18603 • 1-800-AIR-VALV • T: (570) 752-4524 • F: (570) 752-4962 • WWW.CRISPINVALVE.COM • [email protected] A/M

Submittal Sheet for Crispin A/M Series

SUBMITTAL SHEET FO

R A/M SERIES

1/2” Dual Body Combination Air ReleaseManufactured in compliance with ANSI/AWWA C512 Date: 2016

Specifications

ITEM DESCRIPTION MATERIAL ASTM1 TOP CAST IRON A126 CL. B2 FLANGE CAST IRON A126 CL. B3 BODY CAST IRON A126 CL. B4 GASKET ARMSTRONG N-8092 N/A5 SEAT BUNA-N RUBBER D20006S FLOAT STAINLESS-STEEL A2407 HANGER STAINLESS STEEL A2408 CUP STAINLESS STEEL A2409 RIVET STAINLESS STEEL A58211 BOLT STEEL A30712 NUT STEEL A56314 DIFFUSER STAINLESS STEEL A24029 PLUG BRASS B50550 INTERFERENCE PIN STAINLESS STEEL A582

1 VALVE SEAT STAINLESS STEEL A2762 PLUNGER BUTTON VITON D20004 VALVE LEVER STAINLESS STEEL A2405 SCREW (DRIVE) STAINLESS STEEL A1936 BALL FLOAT STAINLESS STEEL A2407 HINGE PIN STAINLESS STEEL A5808 HINGE BUTT STAINLESS STEEL A2409 BOLT STEEL A30710 SCREW STAINLESS STEEL A19311 FLANGE CAST IRON A126 CL.B12H BODY CAST IRON A126 CL.B13 GASKET ARMSTRONG N-8092 N/A29 PLUG (NOT SHOWN) BRASS B505

1 NIPPLE STEEL A532 ELBOW MALLEABLE IRON A3384 NIPPLE STEEL A535 TEE MALLEABLE IRON A338


5/32 40 PSIG 12.6 SCFM1/8 50 PSIG 9.6 SCFM3/32 85 PSIG 8.3 SCFM1/16 150 PSIG 6.1 SCFM3/64 200 PSIG 4.5 SCFM1/32 300 PSIG 3.2 SCFM


Size SpecificationsMODEL INLET SIZE OUTLET SIZE A B WT.A5/M5 1/2” NPT 1/2” NPT 12.00 9.00 20

The combination air valve(s) shall be installed athigh points in the system or at points selected bythe engineer. This will permit discharging thesurge of air from an empty line when filling andrelieve the vacuum when the line is draining, oris under negative pressure. The valve(s) shallalso release the accumulation of air when thesystem is under pressure.The Air and Vacuum Valve shall operate by seal-ing the BUNA-N rubber outlet seat with a periph-erially guided float as the liquid enters the valvechamber to raise the float. All Crispin Valves arehydrostatically tested to 150% of their maximumworking pressure.The Pressure Valve shall operate through acompound lever system and shall have a____________” orifice with valve sealing faces,of an adjustable BUNA-N rubber valve (stainlesssteel or PVC) and shall operate at ___________PSIG and be capable of passing _________SCFM of air. Valves which use a needle valve toseal the orifice will not be acceptable.Valve construction shall be _____________”NPT screwed or ANSI Class (125,250) flangedinlet connection and shall be cast iron body, top,

and inlet flange (where required), stainless steel float with bronze and (brass orstainless steel) trim. Refer to Air & Vacuum and Pressure Air Release specificationsfor Valve description.The valve(s) shall be CRISPIN Model ____________ Dual Air Valve(s), Type N,(PVC seat and BUNA-N rubber valve) or Type P (stainless steel seat and BUNA-N rubber valve) pressure valve(s) as manufactured by Crispin-Multiplex Manufac-turing Co., Berwick, Pa. The valve(s) shall include a Crispin Pressure Air ReleaseValve.Option: A protectop shall be supplied to prevent debris from entering the outlet ofthe Air and Vacuum Valve.Option: (Where pressures are greater than 300 psig), the valve(s) shall be ANSIClass ____________ flanged inlet connection and shall have a (steel, stainlesssteel, or ductile iron) body, top and inlet flange. Standard operating pressure for Crispin Air Valves is 20 to 150 PSIG. Pleasecheck one of the following if your operating needs differ:____ 2 to 40 PSIG ____ 151 to 300 PSIG

PARTS LIST FOR PRESSURE RELEASE UNIT

PARTS LIST FOR CONNECTING PARTS

ACP3

CP4CP3

12H

12

13

CP2CP2

CP1CP1

29

501411

11

10

3

22

1

1

5

5

6

4

7

784

9

9

86S

B

11


5/32 40 PSIG 12.6 SCFM1/8 50 PSIG 9.6 SCFM3/32 85 PSIG 8.3 SCFM1/16 150 PSIG 6.1 SCFM3/64 200 PSIG 4.5 SCFM1/32 300 PSIG 3.2 SCFM

Crispin Valve, 600 Fowler Ave., Berwick, PA 18603 • 1-800-AIR-VALV • T: (570) 752-4524 • F: (570) 752-4962 • WWW.CRISPINVALVE.COM • [email protected]/M

Submittal Sheet for Crispin AL/M Series

SUBM

ITTAL SH

EET FO

R AL

/M SER

IES

1”–3” Dual Body Combination Air ReleaseManufactured in compliance with ANSI/AWWA C512 Date: 2016

SpecificationsThe combination air valve(s) shall be installed at high points in thesystem or at points selected by the engineer. This will permit dis-charging the surge of air from an empty line when filling and relievethe vacuum when the line is draining, or is under negative pressure.The valve(s) shall also release the accumulation of air when the sys-tem is under pressure.The Air and Vacuum Valve shall operate by sealing the BUNA-N rubberoutlet seat with a peripherially guided float as the liquid enters the valvechamber to raise the float. All Crispin Valves are hydrostatically tested at150% of their maximum working pressure.The Pressure Valve shall operate through a compound lever systemand shall have a ______________” orifice with valve sealing faces, ofan adjustable BUNA-N rubber valve (stainless steel or PVC) and shalloperate at _____________ PSIG and be capable of passing___________ SCFM of air. Valves which use a needle valve to seal theorifice will not be acceptable.Valve construction shall be _______” NPT screwed or ANSI Class(125,250) flanged inlet connection and shall be cast iron body, top, andinlet flange (where required), stainless steel float with bronze and (brassor stainless steel) trim. Refer to Air & Vacuum and Pressure Air Releasespecifications for Valve description.The valve(s) shall be CRISPIN Model ____________ Dual Air Valve(s),Type N, (PVC seat and BUNA-N rubber valve) or Type P (stainlesssteel seat and BUNA-N rubber valve) pressure valve(s) as manufac-tured by Crispin-Multiplex Manufacturing Co., Berwick, Pa. The valve(s)shall include a Crispin Pressure Air Release Valve.Option: A protectop shall be supplied to prevent debris from enteringthe outlet of the Air and Vacuum Valve.Option: (Where pressures are greater than 300 psig), the valve(s) shallbe ANSI Class ___________ flanged inlet connection and shall have a(steel, stainless steel, or ductile iron) body, top and inlet flange. Standard operating pressure for Crispin Air Valves is 20 to 150PSIG. Please check one of the following if your operating needs dif-fer: ____ 2 to 40 PSIG ____ 151 to 300 PSIG

SIZE SPECIFICATIONSMODEL INLET SIZE OUTLET SIZE A B C WHT.AL10/M5 1” NPT 1” NPT 9.75 13.25 24AL20/M5 2” NPT 2” NPT 12.25 14.75 53**AL21/M5 2” 125# FLG 2” NPT 12.25 18.25 59*AL22/M5 2” 250# FLG 2” NPT 12.25 18.50 61AL30/M5 3” NPT 3” NPT 16.00 16.00 103AL31/M5 3” 125# FLG 3” NPT 16.00 19.75 120AL32/M5 3” 250# FLG 3” NPT 16.00 20.25 128

8

6

12

SECTION A-A-

427

1110

9 15

13

BC

A-

A-

A

29 11

29

412

63FH

2

1S

29

CP2

CP2

CP3CP1

CP4

5

55

50

ITEM DESCRIPTION MATERIAL ASTM1S TOP CAST IRON A126 CL. B2 FLANGE CAST IRON A126 CL. B3 BODY CAST IRON A126 CL. B4 GASKET ARMSTRONG N-8092 N/A5 SEAT BUNA-N RUBBER D20006 FLOAT STAINLESS-STEEL A24011 BOLT STEEL A30712 NUT STEEL A56329 PLUG BRASS B50550 INTERFERENCE PIN STAINLESS STEEL A5855 EYE NUT FORGED STEEL A563

1 VALVE SEAT STAINLESS STEEL A2762 PLUNGER BUTTON VITON D20004 VALVE LEVER STAINLESS STEEL A2405 SCREW (DRIVE) STAINLESS STEEL A1936 BALL FLOAT STAINLESS STEEL A2407 HINGE PIN STAINLESS STEEL A5808 HINGE BUTT STAINLESS STEEL A2409 BOLT STEEL A30710 SCREW STAINLESS STEEL A19311 FLANGE CAST IRON A126 CL.B12 BODY CAST IRON A126 CL.B13 FLANGE GASKET ARMSTRONG N-8092 N/A

29 PLUG (NOT SHOWN) BRASS B505CP1 NIPPLE STEEL A53CP2 NIPPLE STEEL A53CP3 ELBOW MALLEABLE IRON A338CP4 1/2” GATE VALVE BRASS N/A




** Includes ANSI #125 or #250 companion flange and nipple

12

Crispin Valve, 600 Fowler Ave., Berwick, PA 18603 • 1-800-AIR-VALV • T: (570) 752-4524 • F: (570) 752-4962 • WWW.CRISPINVALVE.COM • [email protected] AL/PL

Submittal Sheet for Crispin AL/PL Series

SUBMITTAL SHEET FOR AL/PL SERIES

4”–10” Dual Body Combo. Air Release (1 of 2)Manufactured in compliance with ANSI/AWWA C512 Date: 2016

SpecificationsThe combination air valve(s) shall be installed at high pointsin the system or at points selected by the engineer. This willpermit discharging the surge of air from an empty line whenfilling and relieve the vacuum when the line is draining, or isunder negative pressure. The valve(s) shall also release theaccumulation of air when the system is under pressure.

The Air and Vacuum Valve shall operate by sealing the BUNA-N rubber outlet seat with a peripherially guided float as the liq-uid enters the valve chamber to raise the float. All Crispin Valvesare hydrostatically tested at 150% of their maximum working pressure.

The Pressure Valve shall operate through a compound lever system and shall have a ______________” orifice with valve sealing faces, of an adjustableBUNA-N rubber valve (stainless steel or PVC) and shall operate at _____________ PSIG and be capable of passing ___________ SCFM of air. Valveswhich use a needle valve to seal the orifice will not be acceptable.

Valve construction shall be _____________” NPT screwed or ANSI Class (125,250) flanged inlet connection and shall be cast iron body, top, and inletflange (where required), stainless steel float with bronze and (brass or stainless steel) trim. Refer to Air & Vacuum and Pressure Air Release specifica-tions for Valve description.

The valve(s) shall be CRISPIN Model ____________ Dual Air Valve(s), Type N, (PVC seat and BUNA-N rubber valve) or Type P (stainless steel seatand BUNA-N rubber valve) pressure valve(s) as manufactured by Crispin-Multiplex Manufacturing Co., Berwick, Pa. The valve(s) shall include a CrispinPressure Air Release Valve.


Option: (Where pressures are greater than 300 psig), the valve(s) shall be ANSI Class __________ flanged inlet connection and shall have a (steel, stain-less steel, or ductile iron) body, top and inlet flange. Standard operating pressure for Crispin Air Valves is 20 to 150 PSIG. Please check one of the follow-ing if your operating needs differ: ____ 2 to 40 PSIG ____ 151 to 300 PSIG



SIZE SPECIFICATIONSMODEL INLET SIZE OUTLET SIZE A C*AL40/PL10 4” NPT 4” NPT 20.00 20.25*AL41/PL10 4” 125# FLG 4” NPT 20.00 23.75*AL42/PL10 4” 250# FLG 4” NPT 20.00 24.25AL61/PL10 6” 125# NPT 6” NPT 21.00 22.25AL62/PL10 6” 250# FLG 6” NPT 21.00 22.50AL81/PL10 8” 125# FLG 8” NPT 24.50 25.50AL82/PL10 8” 250# FLG 8” NPT 24.50 26.00AL101/PL10 10” 125# FLG 10” NPT 33.75 29.00AL102/PL10 10” 250# FLG 10” NPT 33.75 29.75* 4” Valve also available with a 4” NPT inlet

21

9

1N-1P

22A

24

20

228

18

18

192 2523186 22

17

29

SECTION A–A-

713

1310

C

A-

A-

A

29

3

4

6

2

29

131H

CP1

CP1

CP2

CP3

1S

1110

12

555

13



SUBM

ITTAL SH

EET FO

R AL

/PL SE

RIES


ITEM DESCRIPTION MATERIAL ASTM**1H HOOD HRCQ STEEL N/A1S TOP CAST IRON A126 CL.B2 FLANGE CAST IRON A126 CL.B3 BODY CAST IRON A126 CL.B4 GASKET ARMSTRONG N—8092 N/A5 SEAT BUNA—N RUBBER D20006S FLOAT STAINLESS STEEL A240**10 BOLT STEEL A30711 BOLT STEEL A30712 NUT STEEL A56313 BOLT STEEL A30729 PLUG BRASS B50555 LIFTING LUG STEEL A563

*1N VALVE SEAT PVC 1784*1P VALVE SEAT STAINLESS STEEL A5822 VALVE PLUNGER BUNA—N RUBBER & S/S D2000/A1933 PLUNGER NUT STAINLESS STEEL A1943W LOCK WASHER STAINLESS STEEL A2405 VALVE FULCRUM STAINLESS STEEL A5826 VALVE LEVER STAINLESS STEEL A5827 LlNK STAIN LESS STEEL A2408 BALL FULCRUM STAINLESS STEEL A5829 BALL FLOAT STAINLESS STEEL A24010 BALL LEVER STAINLESS STEEL A24011 BEARING PIN STAINLESS STEEL A58212 BEARING PIN STAINLESS STEEL A58213 BEARING PIN STAINLESS STEEL A58215 COTTER PIN STAINLESS STEEL A49317 BOLT STEEL A30718 NUT STEEL A56319 TOP CAST IRON A126 CL.B20 FLANGE CAST IRON A126 CL.B21 BODY CAST IRON A126 CL.B22 FULCRUM WASHER FIBER D71022A FULCRUM WASHER FIBER D71023 SEAT GASKET BUNA—N RUBBER D200024 FLANGE GASKET ARMSTRONG N-8092 N/A25 BOLT STAINLESS STEEL A19329 PLUG BRASS B505

CP1 NIPPLE STEEL A53CP2 STREET ELBOW MALLEABLE IRON A338CP3 1” GATE VALVE BRASS N/A

* Parts are interchangeable and optional at customer’s request ** Optional at customer’s request




AL/PL

14

Crispin Valve, 600 Fowler Ave., Berwick, PA 18603 • 1-800-AIR-VALV • T: (570) 752-4524 • F: (570) 752-4962 • WWW.CRISPINVALVE.COM • [email protected] AL/PL


SUBMITTAL SHEET FOR AL/PL SERIES


SpecificationsThe Combination Air Valve(s) shall be installed at high pointsin the system or at points selected by the engineer. This willpermit discharging the surge of air from an empty line whenfilling and relieve the vacuum when the line is draining, or isunder negative pressure. The valve(s) shall also release theaccumulation of air when the system is under pressure.

The Air and Vacuum Valve shall operate by sealing the BUNA-N rubber outlet seat with a peripherially guided float as the liquid enters the valve chamber to raisethe float. All Crispin Valves are hydrostatically tested to 150% of their maximum working pressure.

The Pressure Valve shall operate through a compound lever system and shall have a ______________” orifice with valve sealing faces, of an adjustableBUNA-N rubber valve (stainless steel or PVC) and shall operate at _____________ PSIG and be capable of passing ___________ SCFM of air. Valveswhich use a needle valve to seal the orifice will not be acceptable.

Valve construction shall be ANSI Class (125,250) flanged inlet connection and shall be cast iron body, top, and inlet flange (where required), stain-less steel float with bronze and (brass or stainless steel) trim. Refer to Air & Vacuum and Pressure Air Release specifications for Valve description.

The valve(s) shall be CRISPIN Model ____________ Dual Air Valve(s), Type N, (PVC seat and BUNA-N rubber valve) or Type P (stainless steel seatand BUNA-N rubber valve) pressure valve(s) as manufactured by Crispin-Multiplex Manufacturing Co., Berwick, Pa. The valve(s) shall include a CrispinPressure Air Release Valve.

Option: A hood shall be supplied to prevent debris from entering the outlet of the Air and Vacuum Valve.

Option: (Where pressures are greater than 300 psig), the valve(s) shall be ANSI Class __________ flanged inlet connection and shall have a (steel, stain-less steel, or ductile iron) body, top and inlet flange.

Standard operating pressure for Crispin Air Valves is 20 to 150 PSIG. Please check one of the following if your operating needs differ: ____ 2 to 40 PSIG ____ 151 to 300 PSIG


3/8 100 PSIG 152 SCFM5/16 150 PSIG 152 SCFM1/4 200 PSIG 127 SCFM3/16 250 PSIG 88 SCFM5/32 300 PSIG 73 SCFM

SIZE SPECIFICATIONSMODEL INLET SIZE OUTLET SIZE A B WHT.

AL121/PL20 12” 125# FLG 12” NPT 34.5 32.5 775AL122/PL20 12” 250# FLG 12” NPT 34.5 33.24 828AL141/PL20 14” 125# FLG 14” NPT 36.5 34.24 1023AL142/PL20 14” 250# FLG 14” NPT 36.5 35 1210AL161/PL20 16” 125# FLG 16” NPT 39.25 36.5 1143AL162/PL20 16” 250# FLG 16” NPT 39.25 37.5 1326

21

9

1N-1P

22A

24

26 29 2320

8

192 25 26

18

2217

15

29

SECTION A–A-

7

13

5123W3611

1310

B

A-

A-

A

29

4

6

3FH

11FA

11F

12

1

2F

CP1

CP4

CP4

CP2

CP3

5

7

89

55

15



SUBM

ITTAL SH

EET FO

R AL

/P SER

IES

12”–16”* Dual Body Combo. Air Release (2 of 2)Manufactured in compliance with ANSI/AWWA C512 Date: 2016

AL/PL

ITEM DESCRIPTION MATERIAL ASTM1H HOOD HRCQ STEEL N/A2F FLANGE CAST IRON A126 CL.B3F BODY CAST IRON A126 CL.B4 GASKET ARMSTRONG N—8092 N/A5 SEAT BUNA—N RUBBER D20006 FLOAT STAINLESS STEEL A2407 FLOAT ROD GUIDE STAINLESS STEEL A5828 SEAT BOLTS STAINLESS STEEL A1939 WASHER STAINLESS STEEL A24010 BOLT STEEL A30711F BOLT STEEL A30711FA BOLT STEEL A30712 NUT STEEL A56329 PLUG BRASS B50555 LIFTING LUG STEEL A240*1N VALVE SEAT PVC 1784

*1P VALVE SEAT STAINLESS STEEL A5822 VALVE PLUNGER BUNA—N RUBBER & S/S D2000/A1933 NUT STAINLESS STEEL A3073W LOCK WASHER STAINLESS STEEL A2405 VALVE FULCRUM STAINLESS STEEL A5826 VALVE LEVER STAINLESS STEEL A5827 LlNK STAIN LESS STEEL A2408 BALL FULCRUM STAINLESS STEEL A5829 BALL FLOAT STAINLESS STEEL A24010 BALL LEVER STAINLESS STEEL A24011 BEARING PIN STAINLESS STEEL A58212 BEARING PIN STAINLESS STEEL A58213 BEARING PIN STAINLESS STEEL A58215 COTTER PIN STAINLESS STEEL A49317 BOLT STEEL A30718 NUT STEEL A56319 TOP CAST IRON A126 CL.B20 FLANGE CAST IRON A126 CL.B21 BODY CAST IRON A126 CL.B22 FULCRUM WASHER FIBER D71022A FULCRUM WASHER FIBER D71023 SEAT GASKET BUNA—N RUBBER D200024 FLANGE GASKET ARMSTRONG N-8092 N/A25 BOLT STAINLESS STEEL A19326 NUT STEEL A56329 PLUG BRASS B50

CP1 NIPPLE STEEL A53CP2 ELBOW MALLEABLE IRON A338CP3 1” GATE VALVE BRASS N/ACP4 NIPPLE STEEL A53

** Optional at customer’s request * Parts are interchangeable and optional at customer’s request




16 * Available up through 24”. Please contact factory for sizes 18” and larger.

Documents

Crispin · and Vacuum Valve, Crispin Pressure Air Valve or Crispin Midget Air Valve literature. All Crispin Valves are hydrostatically tested to 150% of their maximum working pressure