VRTS Industrial Solutions Private Limited, Noida, Industrial And Automotive Products

VRTS Industrial Solution Pvt. Ltd. B-177, Phase – II , Noida – 201305, U.P.

VRTS Industrial Solutions Pvt Ltd – Confidential Page 1

APPLICATION CYCLE FOR FIRE PROTECTION IN AUTOMOTIVE – BARRIER PAINT

APPLICATION: in order to assure a fire protection of the passenger area of a vehicle (railways coach, bus, …) IMPA can offer an intumescent paint that can guarantee 30 minutes of fire protection (if applied with the correct thickness). Such time is more than sufficient to allow all the passengers to leave the vehicle safely.

Step Description Recommended Product

1 Accurate cleaning/decreasing with specific product and tissue of all the surfaces on which is required the application (steel, wood, …)

IMPA Quick Off 0642

2 Application of an adhesion primer on steel or wood parts. The IMPA Khorinthos primer is a water based product that can be applied on wood and metal as well spraying it. With 1 liter of primer a surface of 5-6 sqm can be covered.

IMPA Khorinthos primer 0717

3 Application of intumescent paint water based for fire protection. A layer of Barrier with a thickness of 300 microns is giving 30 min of fire protection. With such thickness 1 kg of paint is covering approx. 2 sqm of surface.

IMPA Barrier 87-1151

4 In order to avoid that the layer of Barrier paint is removed or damaged during the lifetime of the vehicle a protecting layer must be applied on top. Different options are available according to which part of the vehicle is protected by Barrier:

1) PU paint: for parts of the vehicle that are visible

2) Sound dampening product (example: for the bottom of the vehicle)

See below recommended application cycles and products

NOTE: Khorintos primer and Barrier are both water based products. The application cycle above is fully compliant with EU norms for environmental protection. In case the client is covering Barrier with PU paint step 4 is as follow:


4 The paint PU is based on the following componets: - PU paint type 1818 of the required color - Hardner: PU Extra 1873 in ratio of 1 part

each two parts of paint

IMPA PU Paint 1818 IMPA PU Extra 1873 IMPA Diluente Extra 1611



- Thinner: to be added as per required viscosity&application tool – usually 5% to 10% (Diluente Extra 1611)

Paint to be applied in 2 layers, waiting 1-1.5 hours between the two application.

In case the client is covering Barrier with a sound dampening product step 4 is as follow:


4 Sound dampening products from IMPA are: -Antirombo: bitum based paint for sound insulation - Insonorizzante 0325: water based paint for sound&thermal insulation

IMPA Antirombo 1532 IMPA Insonorizzante 0325

Recommended product – Key information:

Product Description Available packaging

IMPA Quick Off 0642 Cleaner degreaser liquid 500 ml bottle or 5 liters tin

IMPA Khorinthos Primer 0717

Adhesion primer for wood and steel 16 liters tin

IMPA Barrier 87-1151 Intumescent paint for fire protection 20 Kg tin

For PU Paint:


IMPA PU Paint 181 PU paint of the required color 20 Kg tin

IMPA PU Extra 1873 Hardener for Pu paint. Ratio is 1 part of hardener each 2 parts of paint

5 Kg tin

IMPA Diluente Extra 1611

Thinner, to be added to the paint+hardener in a ratio that depends by the required viscosity&type of application tool. Usually is between 5% to 10%

5 liter tin



For sound dampening:


IMPA Antirombo 1532 Sound insulation bitumen based paint 1 kg or 4 kg tin

IMPA Insonorizzante 0325

Sound and thermal insulation water based paint 15 Kg tin

TDS and MSDS of all above listed products available on request.

Type of Document Description Issued on Revision

Application cycle Application cycle for fire protection in Automotive

07/06/2013 1



APPLICATION CYCLE FOR FIRE PROTECTION IN BUILDING - BARRIER

APPLICATION: protection against fire of metal (iron, stainless steel, aluminum, light alloys, zinc plated) or concrete structure (pillars, columns,..) with an intumescent paint.


1 Accurate sand blasting of the iron part to be painted.

2 Accurate cleaning and degreasing using a specific product and tissue.

IMPA Quick Off 0642

3 Apply a layer of a 2 component epoxy primer for anti-corrosion. Mix the primer Fondo Anticorrosivo with its hardener INDURITORE EPOX in a ratio 100:20 Dilute adding thinner Diliunte Epox 1612 at:

- 15-20% for spray application - 10% for roller/brush application

IMPA FONDO ANTICORROSIVO EPOX 1293 IMPA INDURITORE EPOX 1871 IMPA Diluente Epox 1612

4 Application of intumescent paint water based for fire protection. A layer of Barrier with a thickness of 300 microns is giving 30 min of fire protection. With such thickness 1 kg of paint is covering approx. 2 sqm of surface.

IMPA Barrier 87-1151

5 Apply a layer of finishing coat or the desidered color using a water based enalmel like TOP LAK. Coverage is 7-8sqm/kg

IMPA TOP LAK 0896




IMPA FONDO ANTICORROSIVO EPOX 1293

Two components anti-corrosion epoxy primer 20 kg tin

IMPA Induritore EPOX 1871

Hardner for Epox product 5 kg tin

IMPA Diluente epox 1612

Thinner for Epox product



IMPA Barrier 87-1151 Intumescent paint for fire protection 20 kg tin

IMPA TOP LAK Water based paint for finishing 18 kg tin



Application cycle Application cycle for fire protection in Building

6/03/2013 1



APPLICATION CYCLE FOR SPOT PAINTING/REPAIRING OF SMALL DEFECTS

APPLICATION: painting cycle for repainting, can be used in car repairs, small defects to be covered at the end of the production line (buses&trucks), small defects to be removed in powder painted parts.


1 Sanding of the part/s with defect

2 Accurate cleaning/decreasing with specific product and tissue

IMPA Quick Off 0642

3 Application of putty IMPA F4 3008

4 Sanding of the putty with sanding paper no.150-180

5 Cleaning using specific product and tissue. IMPA Quick Off 0642

6 Application of a primer. IMPA Filler Spray 2004

7 Sanding of the primer using an abrasive paper with less grit, recommended no. 400.

8 Cleaning using specific product and tissue. IMPA Quick Off 0642

9 Application of PU paint of the desired color, in case the gloss level must be changed add a specific paste at maximum 10% ratio. 2 layers, waiting 1-1.5 hours between the two application.

IMPA Pasta Opacante 1890004

10 Application of an abrasive paste on the area bordering the new painted area & the old painted (or powder painted) surface in order to reduce the color difference (as gloss).

IMPA Polish Abrasive 2200

11 Application of a polishing product to improve the gloss of the full surface (new&old paint).

IMPA Polish Extra Gloss 2201

In case the client is using an IMPA paint STEP 9 is as follow:


9 The paint PU is based on the following componets: - PU paint type 1818 of the required color - Hardner: PU Extra 1873 in ratio of 1 part

each two parts of paint - Thinner: to be added as per required

viscosity&application tool – usually 5% to 10% (Diluente Extra 1611)

Paint to be applied in 2 layers, waiting 1-1.5 hours between the two application.

IMPA PU Paint 1818 IMPA PU Extra 1873 IMPA Diluente Extra 1611

NOTE: in such case is not needed to add “IMPA Pasta Opacante 1890004” because the gloss match is made by IMPA during the color development.





IMPA Quick Off 0642 Cleaner degreaser liquid 500 ml bottle

IMPA F4 3008 Two components polyester filler paste - KIT Available in different packaging:

- 3,6 Kg tin - 1,3 Kg tin

IMPA Filler Spray 2004 One component Filler Spray 400 ml Spray

IMPA Pasta Opacante 1890004

Paste for gloss reduction, max quantity 10% 3,5 Kg tin

IMPA Polish Abrasive 2200

Polish with abrasive effect 1 Liter

IMPA Polish Extra Gloss 2201

Polish for finishing 1 Liter

For Paint:




5 Kg tin



5 liter tin



Application cycle Application cycle for spot painting / repairing of small defects

19/10/2013 1



APPLICATION CYCLE TO IMPROVE RFP PARTS USED IN INTERIOR APPLICATION

APPLICATION: for FRP (Fiber Reinforced Polymers) panels used in interior application in buses or trucks (example: bus dashboard) is mandatory to have a good surface finishing and paintability, such result can be achieved improving the moulds/tools used for production (big investment) or with a correct application of special putty and filler by IMPA


1 Sanding of the part/s with big defect


IMPA Quick Off 0642

3 Application of putty charged with Glass Fiber in order to have good mechanical property and flexibility as well. The putty is needed to close holes, fill dents, fill missing parts and other big defects

IMPA Glass R 3122



IMPA Quick Off 0642

6 Application of a spray filler primer to fill: scratches (also deep ones), cover vast areas full of “pinholes”, cover other surface defects. Thanks to the spray application a vast surface can be quickly covered. One liter of product can cover approx.. 2 sqm of surface.

IMPA Spruzzo 3300



IMPA Quick Off 0642

9 If some small defects are still visible on the surface a 1 component putty ready to use can be used (for pinholes only)

IMPA Finissage 1069

10 Painting

NOTE: step 1,2 and 3 are needed only in case of big holes, dent and missing part of the RFP piece. If defects are scratches, pinholes and so on the cycle can start from step 4. Recommended product – Key information:



IMPA Glass R 3122 Two components universal polyester filler with glass fiber

Available in different packaging:

- 0,3 Kg KIT - 0,8 Kg KIT - 1,2 Kg KIT



IMPA Spruzzo 3300 Two pack primer for spray application 1,05 Liter Kit

IMPA Finissage1069 One component fine filler. Ready to use. 180 grams tube



Application cycle Application cycle to improve surface finishing and paintability of FRP panels for interior

25/05/2013 2



APPLICATION CYCLE TO IMPROVE METAL PARTS TO BE POWDER PAINTED OR SUBJECT TO HEAT CYCLES

APPLICATION: improve the surface of metal parts that are going to be painted with powder coating (high temperature application) or with liquid paint with drying in oven or parts that are exposed to thermal cycle during their usage: in all of the above listed example is needed a putty able to follow the metal expansion/dilatation due to temperature increase


1 Sanding of the part/s with defect


IMPA Quick Off 0642

3 Application of putty charged with metal powder in order to have expansion/dilatation property comparable with the metal

IMPA Metal Fill 3002



IMPA Quick Off 0642

6 Painting as per currently used process (example: powder coating)




IMPA Metal Fill 3002 Two components universal polyester filler with metal powder

Available in different packaging:

- 1 Kg tin KIT - 300 g tin KIT



Application cycle Application cycle to improve metal parts to be powder painted or subject to heat cycles

19/10/2013 1



APPLICATION CYCLE TO PAINT EXTERIOR PLASTIC PARTS – BLACK or GREY

APPLICATION: improving the look of exterior plastic parts of a vehicle (roto-moulded but also injection-moulded such as: fenders, bumpers, mirrors) can require high investment to improve the quality of the mould. As cost effective alternative a surface treatment can achieve the same result. For such application is available a specific application cycle developed by IMPA (only in black or grey color)




IMPA Quick Off 0642

3 Application of putty charged with Glass Fiber in order to have good mechanical property and flexibility as well (IMPA FIBRATO 3105). The putty charged with fiber is needed to close holes and fill missing parts and other big defects. If there are less serious surface defects a standard putty for plastic can be used (IMPA BUMPER FINE STUCK 3106)

IMPA FIBRATO 3105 or IMPA BUMPER FINE STUCK 3106



IMPA Quick Off 0642

6 Paint with special, one component, paint made by IMPA diluted with a specific thinner at 8%-10% ratio. Usually 4-5 sqm/liter is the coverage.

IMPA Bumper Paint 1501 IMPA Diluente Nitro Antinebbia 1616

NOTE:

a) step 1,2 and 3 are needed only in case of big holes, dent and missing part of the plastic part. If defects are scratches, pinholes and non-homogenous color the cycle can start from step 5.

b) Bumper Paint is supplied only in black or grey color and can be applied on several type of plastic (PE, LDPE, HDPE, ABS, PA,…) but not on PET. See TDS for additional information




IMPA FIBRATO 3105 Reinforced polyester filler paste. Two components.

0,8 Kg tin - KIT

IMPA BUMPER FINE STUCK 3106

Fine polyester putty for plastic. Two components.

0,8 Kg tin - KIT

IMPA Bumber Paint Textured one component paint for plastic parts. 1 liter tin



1501

IMPA Diluente Nitro Antinebbia 1616

Cellulose thinner 5 liters tin



Application cycle Application cycle to improve look of exterior plastic parts in black or grey color

19/05/2013 1



APPLICATION CYCLE TO PAINT EXTERIOR PLASTIC PARTS – CUSTOMIZED COLOR

APPLICATION: improving the look of exterior plastic parts of a vehicle (roto-moulded but also injection-moulded such as: fenders, bumpers, mirrors) can require high investment to improve the quality of the mould. As cost effective alternative a surface treatment can achieve the same result o n top of that is also possible to give to the plastic parts a specific color (usually the same of the vehicle).




IMPA Quick Off 0642





IMPA Quick Off 0642

6 Apply a layer of a product to improve adhesion on plastic. Coverage is 10 sqm/liter

IMPA TREND 1540

7 PU paint must be prepared as usual (with the required color), at the paint must be also added a special additive (IMPA FLEXING 1537) at 10% ratio in order to increase the flexibility of the paint. Without such additive the PU paint has a different flexibility compared to the plastic part below it, such difference will lead to paint cracks. Two layers (coats) are needed, between the two application at least 1,5 hours are needed to have the paint dried-up.

For the paint: - IMPA PU Paint 1818 - IMPA PU Extra 1873

(hardener, ratio 1 part each 2 parts of paint)

- IMPA Diluente Extra 1611 (thinner, max 5%-10%)

As additive to increase paint’s flexibility:

- IMPA FLEXING 1537 (to be added at 10%)



IMPA Quick Off 0642 Cleaner degreaser liquid 500 ml bottle or 5 liter tin


0,8 Kg tin - KIT





0,8 Kg tin - KIT

IMPA TREND 1540 Preparatory paint for plastic 0,5 Liter tin



5 Kg tin



5 liter tin

IMPA FLEXING 1537 Flexing additive to be added to paint 0,5 liter tin



Application cycle Application cycle to improve look of exterior plastic parts in customized color

19/05/2013 1



APPLICATION CYCLE TO PAINT INTERIOR PLASTIC PARTS – SOFT TOUCH EFFECT

APPLICATION: improving look and finishing of interior plastic parts of a vehicle (example: bus, van) can changing a lot the perception of the vehicle: from “basic” to “luxury”. But replacing plastic parts with more expensive materials can be a very costly solution. As cost effective alternative a surface treatment can achieve a significant improvement of plastic parts giving a “soft-touch” effect.


1 Sanding of the part/s with big defect (if any)


IMPA Quick Off 0642





IMPA Quick Off 0642

6 Apply a layer of a product to improve adhesion on plastic. Coverage is 10 sqm/liter

IMPA TREND 1540

7 PU paint must be prepared as usual (with the required color), at the paint must be also added a special additive (IMPA FLEXING 1537) at 10% ratio in order to increase the flexibility of the paint. Without such additive the PU paint has a different flexibility compared to the plastic part below it, such difference will lead to paint cracks. Two layers (coats) are needed, between the two application at least 1,5 hours are needed to have the paint dried-up.

For the paint: - IMPA PU Paint 1818 - IMPA PU Extra 1873

(hardener, ratio 1 part each 2 parts of paint)

- IMPA Diluente Extra 1611 (thinner, max 5%-10%)

As additive to increase paint’s flexibility:

- IMPA FLEXING 1537 (to be added at 10%)

8 Paint the part with a special paint giving soft touch effect. The paint is transparent and is giving more or less “soft touch” effect according to the applied thickness. The visible color will be the color of the PU paint applied in the previous step with a “milky”

For the soft touch paint: - IMPA TACTION 1380 - IMPA Hardener for

TACTION 4506 (ratio 1 part of hardener each 5



effect due to the soft touch paint. The paint is a 2 components paint (an hardener is needed) and also a thinner may be needed as per application tool&condition (temperature & humidity)

of paint) - IMPA Diluente Extra

1611 (thinner, 10%-15%)

-

Note: Taction can be applied directly on plastic (not painted) if plastic is ABS or Polycarbonate. In any case an accurate cleaning/degreasing with IMPA Quick Off 0642 is needed. Recommended product – Key information:


IMPA Quick Off 0642 Cleaner degreaser liquid 500 ml bottle or 5 liter tin


0,8 Kg tin - KIT



0,8 Kg tin - KIT

IMPA TREND 1540 Preparatory paint for plastic 0,5 Liter tin



5 Kg tin



5 liter tin

IMPA FLEXING 1537 Flexing additive to be added to paint 0,5 liter tin

IMPA TACTION 1380 Polyurethane two components clear coat with soft touch effect

20 Kg tin

IMPA HARDENER FOR TACTION 4506

Hardener for Taction. Ratio is 1 part of hardener each 5 parts of Taction paint.

4 Kg tin



Application cycle Application cycle to improve look of interior plastic parts giving soft touch effect.

19/05/2013 1



APPLICATION CYCLE TO PAINT METAL PARTS SUBJECT TO VERY HIGH TEMPERATURE

APPLICATION: paint a protect against corrosion metal parts subject to high temperatures like chimneys, ovens, piping used for overheated steam, exhaust pipes and wherever temperature may reach 500-600°C.


1 Accurate sand blasting of the part to be painted.

2 Accurate cleaning and degreasing using a specific product

IMPA Quick Off 0642

3 Apply a layer of inorganic zinc coating to protect against corrosion. ZINCANTE INORGANICO is a 2 components product. Add also thinner Diluente Nitro Antinebbia 1616 at 3-5% ratio

IMPA ZINCANTE INORGANICO 1026 IMPA Diluente Nitro Antinebbia 1616

4 Painting with special silicon paint for high temperature VULKAN. Coverage is 7-8 sqm/liter. The paint must be diluted with IMPA Diluente Nitro Antinebbia 1616:

- At 15-20% ratio for spray application - At 5-10% ratio for brush/roller application

IMPA VULKAN 1127 IMPA Diluente Nitro Antinebbia 1616




IMPA ZINCANTE INORGANICO 1026

Inorganic zinc coating primer. Two components to be mixed with a ration 100:250.

KIT: 1 tin 10 Kg of component A and 1 tin 25 Kg component B

IMPA VULKAN 1127 Silicon enamel with resistance to very high temperature

4 liter tin

IMPA Diluente Nitro Antinebbia 1616

Cellulose thinner 5 liters tin



Application cycle Application cycle to paint metal parts subject to very high temperature.

12/03/2013 1



APPLICATION CYCLE TO PAINT PVC WINDOWS – CUSTOMIZED COLOR

APPLICATION: painting a PVC window can improve the product and differentiate it from a standard “all white” window. The color can be chosed among the RAL color: from a standard brown (to copy the wood) to brilliant colors like red, blue and yellow. The paint can be applied on extruded bar (before cutting and assembly of the window) or on the already assembled window’s frame.



IMPA Quick Off 0642

2 Using a tissue soaked of a special thinner, type Extra PU 1611, clean all the surface to be painted. Such step will “activate” the surface improving the adhesion of the paint to the PVC part.

IMPA Diluente Extra PU 1611

3 Spray the special paint Finitura ADP (of the required color) mixed with its hardener PU Extra 1873 with a ratio of 5 parts of paint and 1 of hardener. Dilute the mix paint+hardener using thinner Extra PU 1611 with a ratio 15-20% Apply 2 coats, after the first wait 10 minutes before apply the second. Coverage 8 sqm/kg.

IMPA Finitura ADP 1846 IMPA PU Extra 1873 IMPA Diluente Extra PU 1611

NOTE: the above descibed cycle can be applied on PVC but also on ABS and PC/ABS plastics. Recommended product – Key information:



IMPA Diluente Extra PU 1611


5 liters tin

IMPA Finitura ADP 1846

Semi-gloss enamel based on acrylic resin and isocyanate adduct.

20 kg tin

IMPA PU Extra 1873 Hardener for paint 5 Kg tin



Application cycle Application cycle to paint PVC windows – Custom color

22/04/2013 1

BARRIER 87-1151 0704.

Water-reducible Intumescent Paint 02/10/13 LRC/nz

Description and use

Intumescent Paint for fire protection of metal structures, metal panels, columns and structures made up of cement, concrete floors, brick walls, etc. In case of fire, special BARRIER 87-1151 components interact at temperatures above 200°C (390°F), producing a non-flammable insulating foam that protects the surface from fire for some time, preventing the structural elements from subsiding, and allowing the fire brigade to intervene and possibly to access the blazing premises without the risk of a structural collapse. The time for which the BARRIER protects against fire is shown in minutes and represents the "Class" of the product. This varies depending on the type of surface and on the thickness of the BARRIER applied. It is recommended to protect structures indoors or not directly exposed to washing away of the rain or to high humidity such as steel or concrete industrial buildings, warehouses, canopies, cinemas, theatres, schools, hospitals, airports, underground stations, etc.

Technical data Colour :white. For technical reasons BARRIER can't be

produced in deep colours. It's possible to get it into light shades or it can be recoated to obtain the required final colour.

Binder Dry film appearance Total non volatile by weight Specific gravity @ 20°C Viscosity @ 20°C Practical coverage Storage life

: vinyl versatate dispersion : matt : 66% ( ± 1) : 1.29 kg/l ( ± 0.04) : 4800 6400 mPa.s Brookfield RVT rpm 50 s 5 : according the requested resistance class. : 12 months in original sealed container.

NB: The storage and application temperature must be kept within + 5°C(41°F) and + 25°C (77°F) This product is Compliant with fire protection requirement for passenger vehicles according to FMVSS 302-2008. Product certification issued by Automotive Research Association - ARAI in 2013 Compliant with Directive 2004/42/CE-IIA(i) maximum VOC limit value: 140 g/l (2010)

Application note

Surface preparation : BARRIER can be applied directly on the surfaces to be protected, provided that they are clean, dry, without dust or grease and made rough by sanding or sand-blasting. On steel surfaces apply a first light coat of a quick drying antirust paint FONDO F.D. code 1859 or KORINTHOS PRIMER code 0717 or FONDO ANTICORROSIVO EPOX code 1293. On galvanized steel, use as an adhesion primer our product KORINTHOS PRIMER or FONDO ANTICORROSIVO EPOX. In case of chalking or fresh concrete, surface must be treated with a layer of fixative masonry sealer CLIM-O-

IMPA Spa - Via Crevada 9/E - 31020 San Pietro di Feletto (TV) Italy - tel. +39 0438 4548 - fax 0438 454915 - www.impa.it - [email protected]

Page 1 / 4

BARRIER 87-1151 0704.

Water-reducible Intumescent Paint

02/10/13 LRC/nz PAINT PRO code 1004, or with a water-thinnable type POLY ACRYL code 0004 or SUPERFIX code 0010.

Product preparation : Mix well to even colour and consistency. Application method : - airless spraying - air mix - roller - brush Reduction : BARRIER is ready to use and should be applied such it

is just to make a sufficient thickness with less possible paint layers. If necessary and according to the application method, BARRIER can be thinned down with 5 10% of water.

Application : - airless spraying: we recommend the use of a high pressure piston or diaphragm pump, gas or electric engine powered (200 250 bar). Choose self-cleaning nozzle and spraying angle according to the structure to be treated but not less than 23 (0.023 inch = 0.58 mm). The angle of the spray nozzle is very important in order to limit waste spraying. - conventional spray gun: use nozzles with large hole ∅ 2.2 2.5 mm @ 3 5 bar pressure.

Air drying time : According to the applied thickness. In ventilated place, at 25°C one coat of 600 µm wet will be recoatable after few hours and will be completely dry after approx. 24 hours.

Suggested thickness : Thickness changes depending on requested protection "Class". Thickness and relative protections (steel or concrete) are well indicated in the Test Certificate. Described thickness must be respected without exceeding, particularly in the corners where too much product can crack during drying time. Apply product in several coats. Do not apply more than 700 800 µm wet for each single coat. One single coat of 800 µm wet can be applied with airless pump and it

correspond to 550 µm dry = 1Kg/m2.

WARNING: Contact our TECHNICAL SERVICE to know the quantity of product to be applied on the structures to be treated. Certificates are issued by Afiti Licof (Spain).


Page 2 / 4

BARRIER 87-1151 0704.


02/10/13 LRC/nz

On STEEL STRUCTURES certified for Class R 15 - 30 - 45 - 60 - 90 - 120 (Certificate n° 2125T10-4 of 27/07/2011) issued by Afiti Licof according to the European Standards UNE ENV 13381-8:2010. On WALLS AND FLOORS certified for Class R 30 - 60 - 90 - 120 (Certificate n° 8689/12-2 of 09/10/2012) issued by Afiti Licof according to the European Standards UNE ENV 13381-3:2004. On BEAMS AND COLUMNS certified for Class R 30 - 60 - 90 - 120 (Certificate n° 8689/12-3 of 09/10/2012) issued by Afiti Licof according to the European Standards UNE ENV 13381-3:2004. On request, integrative reports are worded by an engineer enrolled in the official list of the Ministry of the Interiors, according to law n° 818-84. In accordance with Directive 89/106/EEC on construction products, Barrier 87-1151 has been awarded the European Technical Approval (ETA) and EC mark for compliance with the provisions of ETAG 018 Guidelines - part 1 and part 2. INSTRUCTIONS FOR CONSERVATION AND APPLICATION OF "BARRIER" WATER-BASED 1 - During storage Because of the thixotropic features of the product, after long storage there could occur a thickening. In this case carry out a mechanical stirring by a suitable propeller drill. Avoid temperature below + 5°C (41°F), frozen product can not be used anymore. (BEWARE OF FROST). Avoid storage for long time at temperature over 25°C (77°F). 2 - During application Applying BARRIER outdoor, in open air and in several days, it is absolutely necessary to protect coated surfaces from rain and dew 'till recoating them with a water-proof paint. No caution needed if product will be applied indoor and in a dry place like cinemas, theatres, schools, garages, closed hangars, shopping centres, supermarkets, etc. 3 - After application Avoid washing away by the rain which, because of BARRIER porosity, will go through the film coat getting blisters and flaking, and also dissolving and taking off the active components, leaving the product absolutely inefficient against the fire. Also high moisture or steam will get problems time by time (for example for application in shower room, laundry, dungeon, etc.) because the dampened salts will be partially dissolved, coming up on the surface and causing, after some time, superficial crusts. In such conditions BARRIER must be always protected, overcoating it with a water-proof paint. Apply a protective water-proof coat in the properly thickness, without exceed in quantity because high thickness may stop the free foam expansion in fire conditions. At the end of the coating system, BARRIER will not be sensitive anymore to even strong sudden changes of temperature. Applied product will not loose its intumescent features,


Page 3 / 4

BARRIER 87-1151 0704.


02/10/13 LRC/nz

provided that there will not happen one of the above described conditions, and the application has be done following exactly all the instructions. NOTE: Information provided in this technical data sheet is based upon our best experience and technical knowledge; it does not absolve the users from carrying out tests and preventive checks in order to verify the suitability for use. For further technical information or for suggestions about specific systems and/or applications, please contact our TECHNICAL SERVICE. FOR PROFESSIONAL USE ONLY

This note replaces all the previous ones. Please, make sure to have the latest issue. The above mentioned data are meant to facilitate our customers in the use of our products. IMPA is not responsible for applications of products carried out beyond its direct control. IMPA Spa - Via Crevada 9/E - 31020 San Pietro di Feletto (TV) Italy - tel. +39 0438 4548 - fax 0438 454915 - www.impa.it - [email protected]

Page 4 / 4

BUMPER PAINT Textured paint for bumpers and plastic trims

1501. 01/09/10 LRB/nz


Page 1 / 2

Description and use One-component product offering excellent adhesion to most of plastic surfaces used in car bumpers manufacturing (polypropylene, polycarbonate, ABS, Pocan, xenoy, rigid polyurethane, fiberglass reinforced polyester, etc. except for polyethylene and mixture containing this stuff). It features fast drying, high adhesion, excellent resistance to washing and weathering; semi-matt appearance like the original bumpers. It can be used as a finishing treatment or as adhesion primer, also before applying the polyester filler FIBRATO code 3105.

Technical data Colour : see price list Binder : blend of alkyd and acrylic resins Dry film appearance : semi-matt - 15 ÷ 20 gloss (Gardner 60°) Specific gravity : 1.12 kg/l ( ± 0.02) Viscosity : 2000 ÷ 2400 mPa.s Brookfield RVT rpm 50 s 5 Practical cover rate : 3 ÷ 5 m²/l according the applied thickness. Storage life @ 20°C.(68°F.) : 24 months in original sealed container. NB: Data recorded @ 20°C.(68°F.) The product is compliant with Directive 2004/42/CE-IIB(c) maximum VOC limit value: 540 g/l

Application note Substrate preparation : Surface to be treated must be dry, clean and free from

oil, bitumen and mud stains. Clean off silicon or polishing wax traces using a wipe

soaked with ANTISILICONE code 1618. Product preparation : Stir well to even colour and consistency. Application method : - air mix spray gun with nozzle ∅ 1.7 ÷ 1.9 mm and pressure of 2 ÷ 3 bar. Reduction : To obtain a thick texture: do not reduce. Add 10% of DILUENTE NITRO ANTINEBBIA (cellulose

thinner) code 1616 for a normal texture or if used as a primer.

Suggested thickness : 50 ÷ 100 μm dry film high thickness is not needed. Air drying @ 20°C. : Touch free : 30 minutes with thickness of 80 ÷ 100 μm Dry through : 8 hours Recoatable : after 4 ÷ 6 hours

BUMPER PAINT Textured paint for bumpers and plastic trims

1501. 01/09/10 LRB/nz

This note replaces all the previous ones. Please, make sure to have the latest issue. The above mentioned data are meant to facilitate our customers in the use of our products. IMPA is not responsible for applications of products carried out beyond its direct control.


Page 2 / 2

NOTE: Information provided in this technical data sheet is based upon our best experience and technical knowledge; it does not absolve the users from carrying out tests and preventive checks in order to verify the suitability for use. For further technical information about specific systems and/or special applications, please contact our TECHNICAL SERVICE. FOR PROFESSIONAL USE ONLY

F4 Polyester filler paste for steel and fiberglass

3008. 06/09/10 LRD/nz


Page 1 / 2

Description and use Two-pack filler paste featuring quick hardening and strong adhesion. The paste is easy to spread and allows to obtain both great thickness and thin layers. The sanding work is quick and easy, the sandpaper will not fill or clog. Recommended for all traditional car body work in which the dry sanding is used. Product also suitable for nautical use.

Technical data Colour : yellow Binder : blend of unsaturated polyester resins Specific gravity∗∗ : part “A”: 1.78 kg/l ( ± 0.03) Hardener : paste code 4000 Curing ratio : 100 of A + 1 ÷ 3 of B by weight Gel time∗∗ : 5 ÷ 7 minutes with 2 parts by weight of hardener to 100 parts of A Complete polymerisation∗∗ : after 2 hours Sandability∗∗ : after 30 minutes on medium thickness Flexibility : medium Water resistance : excellent Solvent resistance : excellent Storage life∗∗ : 12 months in original sealed container, away from light. ∗∗Data recorded @ 20°C.(68°F.). The product is compliant with Directive 2004/42/CE-IIB(b) maximum VOC limit value: 250 g/l

Application note Suitable surfaces : Steel, cast iron, aged car paints and fiberglass free of

detaching agents. For any further information apply to our TECHNICAL

SERVICE. Not suitable surfaces : Wash primer, epoxy primers with phenolic hardeners,

thermoplastic varnishes, solvent sensitive primers. On aluminium, zinc plated steel and light alloys we

recommend the use of our universal polyester fillers. Surface preparation : Surfaces to be filled must be dry, clean, free of dust or

grease, and made rough by sanding. Application method : spatula (blade) Product preparation : To use the filler, add the hardener according to the

room temperature and the requested gel time, like the following schedule:

F4 Polyester filler paste for steel and fiberglass

3008. 06/09/10 LRD/nz



Page 2 / 2

Suggested ratio for a temperature Tube (by weight) up to 10°C. (50°F.) 3 to 100

10 ÷ 20°C. (50 ÷ 68°F.) 2 to 100 over 20°C. (68°F.) 1 to 100

Stir thoroughly the two components and apply making a light pressure on the spatula, to get a better adhesion. For the sanding work it’s suggested the use of sandpaper P80, P120, P180, P240 grit. For best final result, before applying the top-coat spray over the filler a coat of the High Solids Primer EQUALIX HS Code 1513. Infrared rays lamps. Using medium or short waves IR lamps, waiting time before sanding can be reduced, getting at the same time a more dry surface. After application allow some minutes before radiating the filler. It is important that filler temperature never exceeds 60°C.(140°F.) Refer to the lighting system manufacturer to get correct user information (e.g. times and distances). NOTE: Avoid to apply when temperature is below + 10°C.(50°F.) Information provided in this technical data sheet is based upon our best experience and technical knowledge; it does not absolve the users from carrying out tests and preventive checks in order to verify the suitability for use. For further technical information about specific systems and/or special applications, please contact our TECHNICAL SERVICE.

FINITURA ADP Finish with direct adhesion to PVC, ABS and PC/ABS

1846. 11/03/10 LRB/nz


Page 1 / 2

Description and use Semigloss enamel based on acrylic resin and isocyanate adduct. Recommended for use on properly prepared plastic substrates. It can be coloured using the ADVANCE HT/IMPASYSTEM tinting system.

Technical data Colour : on request Pot-life : 4 ÷ 6 hours Dry film appearance : semigloss - 45 ÷ 60 gloss (Gardner 60°) depending on thickness. Viscosity : Part “A” : 60 ÷ 80 seconds ISO-DIN Cup # 4 Practical cover rate∗ : 8 ÷ 9 m²/kg per two coats. Storage life : 12 months in original sealed container. ∗The cover rate is calculated on the suggested thickness and applied on plane and regular surfaces. NB: Data recorded @ 20°C.(68°F.)

Substrate preparation PVC/ABS/PC/ABS: clean and degrease by using ANTISILICONE code 1618, then pass with a cloth soaked of DILUENTE EXTRA PU code 1611, wait until the surface becomes matt, next apply FINITURA ADP. TRANSPARENT PLEXIGLASS: clean only using ANTISILICONE.

Preparation Stir thoroughly the product to achieve even colour and consistency, then add the suitable hardener in the following ratio:

BY WEIGHT / IN PESO

PRODUCT / PRODOTTO 1846 FINITURA ADP

100

HARDENER / INDURITORE 4300 INDURITORE STANDARD or else/oppure 4500 INDURITORE FAST

20

THINNER / DILUENTE 1611 DILUENTE EXTRA PU or else/oppure 1653 DILUENTE PER ACRILICI

15 ÷ 20

Application method : - air mix spray gun with nozzle ∅ 1.2 ÷ 1.4 mm and pressure of 3 ÷ 4 bar. Recommended thickness : 30 μm dry film in two-three layers, waiting 5 ÷ 10

minutes between them.

FINITURA ADP Finish with direct adhesion to PVC, ABS and PC/ABS

1846. 11/03/10 LRB/nz



Page 2 / 2

DRYING TIME / ESSICCAZIONE Dust free Fuori polvere

Handling Al tatto

Through drying In profondità

Air drying/Aria @ 20°C.65%R.H./U.R.

15 ÷ 20 minutes/min. 4 ÷ 6 hours/ore 24 ÷ 36 hours/ore

Oven/Forno @ 60°C. Flash off/ Appassimento: 20 ÷ 30 min.

50 ÷ 60 minutes

NOTE: Apply only the suggested thickness. Otherwise, and especially in case of high environment temperature, blisters may come up on the film surface. Do not apply the product after the suggested pot-life; the forming film will have bad adhesion to the substrate. Information provided in this technical data sheet is based upon our best experience and technical knowledge; it does not absolve the users from carrying out tests and preventive checks in order to verify the suitability for use. For further technical information about specific systems and/or special applications, please contact our TECHNICAL SERVICE. FOR PROFESSIONAL USE ONLY

FLEXING Flexibility additive for one- and two-comp. systems solvent-based

1537. 21/05/09 LRB/nz



Page 1 / 1

Description and use Recommended when the flexibility has to be long lasting in the varnishes, enamels and primers applied over flexible surfaces.

Technical data Appearance : thick liquid Colour : transparent yellowish Binder : polyurethane Specific gravity : 1.08 kg/l ( ± 0.02) Storage life : 24 months in original sealed container. NB: Data recorded @ 20°C.(68°F.)

Application note Product preparation : This flexing additive has a good compatibility with

systems based on polyurethane, acrylic, vinyl and cellulose resins.

Poorly compatible with systems based on Cellulose Acetate-Butyrate (matt base).

In one-component systems, add the product with 5 ÷ 8% of FLEXING; in two-components systems, use 10 ÷ 15% of FLEXING, according to the support flexibility.

Next, cure or reduce the product as recommended in the Technical Data Sheet relating to the same product.

Plastic bumpers, cycle for coating: 1. Primer for plastic (TREND code 1540 or TRONIC code 1541) 2. Filling Primer such as EQUALIX HS modified with 10% of FLEXING, subsequently sand-down 3. Possible matt base 4. Clear-coat additivated with 10% of FLEXING NOTE: The use of the primer is necessary where a smooth finish is required but, for coating not textured plastic parts, the finishing varnish can be applied directly over the primer. In case of application over high flexible parts, increase the quantity of additive up to 15%. Information provided in this technical data sheet is based upon our best experience and technical knowledge; it does not absolve the users from carrying out tests and preventive checks in order to verify the suitability for use. For further technical information about specific systems and/or special applications, please contact our TECHNICAL SERVICE. FOR PROFESSIONAL USE ONLY

GLASS “R” Polyester filler paste reinforced with glass fibers

3122. 29/02/08 LRD/nz


Page 1 / 2

Description and uses Two-pack filler paste based on unsaturated polyester resins with added special glass fibers which give to the mass high mechanical features and surface hardness. This allows to reconstruct missing or strongly damaged small parts of the car body, and to fill holes thanks to the bridges of fibers that are formed above the empty points. Tough, medium hard, high water resistant, it can be sanded with rotate-orbital sander, and can be recoated with other putties or with any type of finishing product. Product also suitable for nautical use.

Technical data Colour : kaki green Binder : unsaturated polyester resin Specific gravity∗∗ : part “A”: 1.70 kg/litre ( ± 0.03) Hardener : paste code 4000 (tube) Curing ratio : 100 of “A” + 1 ÷ 3 of “B” by weight Gel time∗∗ : 6 ÷ 8 minutes with 2 parts by weight of hardener to 100 parts of “A” Complete polymerisation∗∗ : after 3 hours Sandability∗∗ : after 40 minutes on medium thickness Flexibility : medium Water resistance : good Solvent resistance : good Storage life∗∗ : 12 months in original sealed container, away from light. ∗∗Data recorded @ 20°C.(68°F.) The product is compliant with Directive 2004/42/CE-IIB(b) maximum VOC limit value: 250 g/l

Application note

Suitable surfaces : Steel, cast iron, aged car paints and fiberglass free of detaching agents.

For any further information apply to our TECHNICAL SERVICE.

Not suitable surfaces : Wash primer, epoxy primers with phenolic hardeners,

thermoplastic varnishes, solvent sensitive primers. Aluminium, light alloys, zinc plated steel and surfaces

with bad adhesion must be previously treated with a non phenolic or acid cured adhesion primer.

Surface preparation : Surface to be filled must be dry, clean, free of dust or

grease, and made rough by sanding. The rust must be removed as much as possible. Application method : spatula

GLASS “R” Polyester filler paste reinforced with glass fibers

3122. 29/02/08 LRD/nz



Page 2 / 2

Product preparation : To use the filler, add the hardener according to the room temperature and the requested gel time, like the following schedule:

Suggested ratio for a temperature Tube (by weight) up to 10°C. (50°F.) 3 to 100

10 ÷ 20°C. (50 ÷ 68°F.) 2 to 100 over 20°C. (68°F.) 1 to 100

Stir thoroughly the two components up to get an homogeneous paste. Apply the filler pressing down the spatula in order to have the best adhesion, using the long fibers to restore the lacking parts or to clog the holes. After 30 ÷ 40 minutes, level with an abrasive disc or with the rotate-orbital sander using sandpaper P60-P80 grit. If necessary, repeat application with a non reinforced polyester filler. NOTE: Avoid to apply when temperature is below + 10°C.(50°F.) Information provided in this technical data sheet is based upon our best experience and technical knowledge; it does not absolve the users from carrying out tests and preventive checks in order to verify the suitability for use. For further technical information or for suggestions about specific systems and/or applications, please contact our TECHNICAL SERVICE.

METAL FILL Universal polyester filler with metal powder

3002. 06/09/10 LRD/nz


Page 1 / 2

Description and use Highly resistant and hard filler paste which can be applied on most metals. It is made up of unsaturated polyester resins, inert mineral and metallic extenders. Its lamellar structure ensures excellent adhesion even to difficult surfaces and in special condition, when ordinary fillers mechanical properties may be subjected to alterations. Especially recommended to reconstruct corroded metal parts and rusty fenders, to fix pieces by threading of the hardened filler, and to restore damaged parts on various substrates. Product also suitable for nautical use.

Technical data Colour : iron grey Hardened product appearance : metal alike Binder : unsaturated polyester resins with high adhesion and resistance Specific gravity∗∗ : part A: 1.48 kg/l ( ± 0.03) Hardener : paste code 4000 Curing ratio : 100 parts of A + 2 ÷ 3 parts of B by weight. Gel time∗∗ : 4 ÷ 5 minutes with 2 parts by weight of hardener to 100 parts of A Complete polymerization∗∗ : after 1 hour Workable∗∗ : after 30 minutes on medium thickness Flexibility : low Water resistance∗∗ : excellent Extension (traction) resistance∗∗ : approx. 300 Kg on thread 8 x 1,25 MA Adhesion∗∗ : indicative data registered by BS 5350 C5 method: Fe PO4 : 570 Kg/inch² rolled aluminium UNI 4507 : 420 Kg/inch² casting aluminium : 400 Kg/inch² electro-zinc plated sheet : 600 Kg/inch² Property of the polymerised filler : resistance indicative value: dip in water @ 40°C.(104°F.) : more than 15 days @ 150°C. (302°F.) of temperature: more than 3 hours to the thermal chock: more than 40 cycles from 0 to 100°C.( 32 to 112°F.) in 15 days. to the acid of battery : more than 24 hours unaltered in discontinuous contacts with hydrocarbons

and solvents in general. Storage life∗∗ : 12 months in original sealed container, away from light. NB: Data recorded @ 20°C.(68°F.) The product is compliant with Directive 2004/42/CE-IIB(b) maximum VOC limit value: 250 g/l

Application note

METAL FILL Universal polyester filler with metal powder

3002. 06/09/10 LRD/nz



Page 2 / 2

Suitable surfaces : Steel, cast iron, aluminium, light alloys, zinc plated steel and fiberglass free of detaching agents.

For any further information apply to our TECHNICAL SERVICE.

Not suitable surfaces : Wash primer, epoxy primers with phenolic hardeners,

thermoplastic varnishes, solvent sensitive primers. Copper and its alloys must be previously treated with a

non-phenolic or acid cured adhesion primer. Surface preparation : Surfaces to be filled must be dry, degreased, roughed

and free of existing paints. Application method : spatula (blade) Product preparation : To use the filler, add the hardener according to the

room temperature and the requested gel time, like the following schedule:

Suggested ratio for a temperature Tube (by weight)

up to 15°C. (59°F.) 3 to 100 over 15°C. (59°F.) 2 to 100

Stir thoroughly and apply the filler pressing down the spatula in order to have the best adhesion. The hardened filler can be worked with an abrasive disc for metal after about 30 minutes with a temperature ambient/metal of 17 ÷ 30°C.(62 ÷ 86°F.) or after 50 minutes when it is 10 ÷ 17°C. NOTE: Avoid to apply when temperature is below + 10°C.(50°F.) Information provided in this technical data sheet is based upon our best experience and technical knowledge; it does not absolve the users from carrying out tests and preventive checks in order to verify the suitability for use. For further technical information about specific systems and/or special applications, please contact our TECHNICAL SERVICE.

SILISTONE Siloxane-based strengthening water-repellent primer

1346. 01/02/11 LRC/nz


Page 1 / 2

Description and use Clear consolidating water-repellent product, based on siloxane-resins, suitable to protect buildings and stone items; it doesn’t allow water and humidity to penetrate, and protects from acid rain. It also acts to strengthen chalking or corroded stones, preventing them from flaking and crumbling. It is perfectly invisible and does not give the treated pieces a wet or glossy look, preserving their original appearance unchanged. It is recommended to protect any type of masonry or stone: façades, window sills, statues, cement, marble, bricks, where protection against mildew and moisture are required, and to strengthen the piece itself too.

Technical data Colour : transparent-colourless Binder : polysiloxane resins Specific gravity : 0.80 kg/l ( ± 0.01) Practical cover rate : 2 ÷ 4 m²/l according the surface absorption. Storage life : 12 months in original sealed container NB: Data recorded @ 20°C.(68°F.) The product is compliant with Directive 2004/42/CE-IIA(h) maximum VOC limit value:750 g/l (2010)

Application note Substrate preparation : Surfaces to be treated must be dry and clean; take off

stains, moulds and scaling, otherwise they will remain encapsulated and the following removing might result difficult.

Application method : - brush - roller Application by brush is suggested, as it ensures a

better penetration of the product. A preliminary test on the material to be treated allows to

obtain a value of real consumption. Reduction : Product is ready-to-use. Air drying @ 20°C. : 20 ÷ 30 minutes To use correctly, apply SILISTONE by brush, making a light pressure in order to allow it to enter cracks, corners and cavity. Repeat application again and again, without interruption, until the stone will be soaked and will not absorb product anymore. In case of small pieces, SILISTONE can be used dipping the items; it is also possible to spread it using an imbued sponge, taking care to wear protective rubber gloves. NOTE: Do not apply in foggy or rainy weather.

SILISTONE Siloxane-based strengthening water-repellent primer

1346. 01/02/11 LRC/nz



Page 2 / 2

Exterior applications need to be protected from rain for at least 24 hours. Information provided in this technical data sheet is based upon our best experience and technical knowledge; it does not absolve the users from carrying out tests and preventive checks in order to verify the suitability for use. For further technical information about specific systems and/or special applications, please contact our TECHNICAL SERVICE. FOR PROFESSIONAL USE ONLY

SPRUZZO Spray polyester primer

3300. 09/05/13 LRD/nz


Page 1 / 2

Description and use Two-pack primer for spray application based on unsaturated polyester resins to be cured with a liquid organic peroxide. It may be sanded both dry or wet conditions. It is suitable for applications in industry and car body shop instead of regular filler paste, especially in case of large or complex surfaces.

Technical data Colour : grey Specific gravity∗∗ : part “A”: 1.54 kg/l ( ± 0.03) Viscosity∗∗ : part “A”: 35 seconds ( ± 5) ISO-DIN Cup # 8 Hardener : liquid code 4401 Gel time∗∗ : 25 minutes ( ± 3) Complete polymerisation∗∗ : after 24 hours Sandability : after 3 hours @ 20°C, after 30 minutes @ 60°C(140°F.) or IR radiation. Flexibility : good Water resistance : very good Solvent resistance : good Practical coverage∗ : 2 m²/l Storage life∗∗ : 12 months in original sealed container, away from light. ∗The practical coverage is calculated on the suggested thickness and applied on plane and regular surfaces. ∗∗Data recorded @ 20°C (68°F.) and 65% R.H. The product is compliant with Directive 2004/42/CE-IIB(b) maximum VOC limit value: 250 g/l

Application note Suitable surfaces : Steel, cast iron, aged car paints and fiberglass free of

detaching agents. For any further information apply to our TECHNICAL

SERVICE. Not suitable surfaces : Aluminium, zinc plated steel and light alloys, wash

primer, epoxy primers with phenolic hardeners, thermoplastic varnishes, solvent sensitive primers.

Surface preparation : Surface must be dry, clean, free from dust or grease,

and made rough by sanding. Product preparation : Stir thoroughly the part “A” before using, than add the

hardener in the following ratio:

SPRUZZO Spray polyester primer

3300. 09/05/13 LRD/nz



Page 2 / 2

BY WEIGHT / IN PESO BY VOLUME / IN VOLUME

PRODUCT / PRODOTTO 3300 SPRUZZO

150 100

HARDENER / INDURITORE 4401 CATALIZZATORE LIQUIDO

5 5

Do not cure quantities more than 1 kg on purpose to

avoid the “mass effect” which reduces notably the life time of the mixture. Clean equipment immediately after use with CELLULOSE thinner.

Reduction : Not required, if necessary 5% maximum with

DILUENTE PER POLIESTERE (thinner for polyester) code 1626.

Application method : - air mix spry gun with nozzle ∅ 2.2 ÷ 2.5 mm and pressure of 2 ÷ 4 bar. Suggested thickness : 400 μm dry film Overcoatable : After dry sanding using P240 grit or more fine, using

P120 or more fine if wet sanded. For best result, spray a coat of insulating primer

EQUALIX HS code 1513 or STAR PRIME HT code 1543 before applying the finishing paint.

NOTE: Avoid to apply when temperature is below + 10°C (50°F.) Information provided in this technical data sheet is based upon our best experience and technical knowledge; it does not absolve the users from carrying out tests and preventive checks in order to verify the suitability for use. For further technical information about specific systems and/or special applications, please contact our TECHNICAL SERVICE. FOR PROFESSIONAL USE ONLY

TACTION Polyurethane clear-coat with soft touch effect

1380. 26/07/11 LRB/rz


Page 1 / 2

Description and use 2K, non-yellowing matt clear-coat with a particular tactile effect like velvet, used on different sectors from car bodywork (interior parts of cars), furniture, objects, wherever it is required a "soft touch" effect. It is easy to apply, with good scrub resistance properties and it can be applied on various types of properly prepared supports.

Technical data Colour : opalescent, colourless Pot-life : 3 hours Dry film appearance : matt Viscosity : part “A” : 15 ÷ 35 seconds ISO-DIN Cup # 6 Specific weight : Part “A” : 1.02 kg/l ( ± 0.02) Part “B” : 1.04 kg/l ( ± 0.01) Practical cover rate∗ : 6 ÷ 7 m²/kg per two coats. Storage life : 24 months in original sealed container. ∗The cover rate is calculated on the suggested thickness and applied on plane and regular surfaces. NB: Data recorded @ 20°C (68°F). Substrate preparation IRON SURFACES: In case of old and firmly adhering to the surface 2K paints, carry out a slight sanding with sandpaper P320 followed by a cleaning with ANTISILICONE code 1618. ABS and Polycarbonate: sand and clean carefully with ANTISILICONE. On other surfaces use a suitable adhesion primer or contact our technical service.

Preparation

To ensure an excellent result, we recommend to shake slightly until having a homogeneous product; then add the hardener in the following ratio and stir again: BY WEIGHT / IN PESO BY VOLUME / IN VOLUME

PRODUCT / PRODOTTO 1380 TACTION

100 5

HARDENER / INDURITORE 4506 INDURITORE PER PU TACTION

20 1

THINNER / DILUENTE 1611 DILUENTE EXTRA PU

10 ÷ 15

10 ÷ 15

Application method : - air mix spray gun with nozzle ∅ 1.2 ÷ 1.4 mm and

pressure of 2.5 ÷ 3.5 bar. Recommended thickness : 50 ÷ 60 μm dry film with two coats.

TACTION Polyurethane clear-coat with soft touch effect

1380. 26/07/11 LRB/rz



Page 2 / 2

Tactile effect can change according to the applied thickness.

DRYING TIME / ESSICCAZIONE Through drying In profondità

Oven/Forno @ 50°C Flash off/ Appassimento: 10 minutes

90 minutes

Oven/Forno @ 80°C Flash off/ Appassimento: 10 minutes

60 minutes


TREND Preparatory product for plastic parts

1540. 19/01/07 LRD/nz


Page 1 / 2

Product description TREND is a car body product especially studied to prepare plastic materials before applying sanding primers, wet-on-wet primers and finishing coats.

Recommended use Car body shop and industrial works.

Technical data Colour : transparent Type of product : one-pack Specific gravity : 0.89 kg/litre ( ± 0.01) Practical cover rate∗ : 10 ÷ 12 sq.mt./litre Storage life : 24 months in original sealed container. ∗The cover rate is calculated on the suggested thickness, applied on plane and regular surfaces, and can change according to the surface roughness and absorption. NB: Data recorded @ 20°C.(68°F.) The product is compliant with Directive 2004/42/CE-IIB(a) maximum VOC limit value: 850 g/l

Application note Substrate preparation : Surface to be treated must be dry, clean, free from tar,

oil stains and mud. Wash thoroughly with water and soap the plastic parts, next degrease with DILUENTE ANTISILICONE code 1618.

Product preparation : Product is ready-to-use. Application method : - air mix spray gun with nozzle ∅ 1.2 ÷ 1.4 mm and pressure of 2.5 ÷ 3 bar Suggested thickness : 5 ÷ 10 μm dry film Air drying @ 20°C. : Dust free : ~ 2 minutes Touch free : ~ 5 minutes Dry through : ~ 10 minutes Recoatable : after 10 ÷ 15 minutes. When primers, light colour top coats or clear on base

varnishes have to be applied over flexible or very flexible surfaces, it is necessary to add these products with FLEXING code 1537, according to the percentage suggested in the Technical Data Sheet relating to the product.

TREND Preparatory product for plastic parts

1540. 19/01/07 LRD/nz



Page 2 / 2

Types of plastic used in the car industry: PP= Polypropylene PE= Polyethylene PP/EPDM= Polypropylene/modified rubber PE/EPDM= Polyethylene/modified rubber ABS= Acrylonitryle-butadiene PA= Polyamide PPO= Polyfenylenoxide PVC= Polyvinyl Chloride PUR= Polyurethane P.D.T.= Polybuthylene tereftalate (Pocan) NOTE: Information provided in this technical data sheet is based upon our best experience and technical knowledge; it does not absolve the users from carrying out tests and preventive checks in order to verify the suitability for use. For further technical information about specific systems and/or special applications, please contact our TECHNICAL SERVICE.

VULKAN Silicon enamel with resistance to very high temperatures

1127. 03/08/09 LRB/nz


Page 1 / 2

Description and use Product based on silicone resins highly resistant to heat and pigments designed to be stable at high temperatures (over 500°C, 932°F.). Recommended to paint metal chimneys, ovens, chemical plants exposed to high temperatures, piping used for overheated steam or diathermic fluids, exhaust pipes, manifolds and wherever temperatures may reach 500 ÷ 600°C.

Technical data Colour : black and aluminium Binder : silicon resin Dry film appearance : matt Practical cover rate∗ : 7 ÷ 8 m²/l per two coats Storage life : 12 months in original sealed container. ∗The cover rate is calculated on the suggested thickness and applied on plane and regular surfaces. NB: Data recorded @ 20°C.(68°F.)

Application note Substrate preparation : FERROUS SURFACES: we recommend sand-blasting

to SA2.5 grade, or thorough mechanical cleaning, followed by degreasing with solvents and application of a first coat of primer ZINCANTE INORGANICO code 1026. If the full painting system cannot be carried out, apply VULKAN directly on the substrate treated as above.

Product preparation : Stir well to achieve even colour and consistency. Reduction : 15 ÷ 20% with DILUENTE NITRO ANTINEBBIA

(cellulose thinner) code 1616 for the spray application, 5 ÷ 10% when using a brush or roller.

Application method : - air mix spray gun with nozzle ∅ 1.5 ÷ 1.7 mm and pressure of 3 ÷ 4 bar.

- airless spraying - brush - roller

Recommended thickness : 40 ÷ 50 μm dry film Air drying @ 20°C. : Dust free : 10 ÷ 20 minutes Dry through : 24 hours Cross-link : 1 hour @ 200 ÷ 250°C. (396

÷ 482°F.) NOTE: To ensure chemical and mechanical resistance, the product requires heating up to 200 ÷ 250°C for about 1 hour, to allow full resin cross-linking.

VULKAN Silicon enamel with resistance to very high temperatures

1127. 03/08/09 LRB/nz



Page 2 / 2


Business

VRTS Industrial Solutions Private Limited, Noida, Industrial And Automotive Products