Upload
guest3a1b5518
View
318
Download
0
Embed Size (px)
Citation preview
www.gspamerica.com
Understanding POE
By Peter Brissette
GSP America
www.gspamerica.com
What is POE?
• Power over Ethernet is defined across a single network link. The three basic components of a PoE connection are:
• The equipment that delivers power to the cable (often referred to as a PSE, which stands for power sourcing equipment)
• The device which receives its power from the cable (also known as a powered device, or PD)
• The cable itself
www.gspamerica.com
Examples
• Typical PDs include IP cameras, wireless access points (APs), etc., and the PSE would normally be a PoEenabled network switch or a midspan power injector, patched in to add PoE capability to a non PoE network switch channel or similar.
www.gspamerica.com
Power Classification
• As a part of the start-up process when a PoEconnection is made, the PD can “advertise” its power class, which is an indication of how much
electrical power it requires to operate.
Wireless AP12.95 watts15.4 watts3, 4, or 0
IP video camera
6.49 watts7 watts2
VoIP Telephone
3.84 watts4 watts1
Example PDMax. PD PowerMin PSE PowerClass
www.gspamerica.com
Power Classification
• Note also that these figures are upper limits to power. Power cannot be “forced”down the cable – a surprisingly common misconception.
• The PD simply presents a load to the cable and draws as much current as it needs.
• Most PoE-powered devices will draw a fixed level of power.
www.gspamerica.com
Power management
• Two Kinds of POE Switches
• There is the kind that operates with a
“guarantee per port” and the kind that operates with a “total power budget”.
www.gspamerica.com
Power Management
• Guarantee per port means that you can
connect as many Class 3 or 0 devices and
the switch will be able to power them.
(15.4 watts each)
– More expensive
– Bigger
– Better in controlled environment
www.gspamerica.com
Power Management
• Total Budget Switch – Can only power as many devices as it has power to spare
• Example: 4 port switch with total of 30 watts.
• 4 Class 2 Devices (4 x 7.5 watts = 30 watts) – this is OK
• 2 Class 3 Devices (2 x 15 watts = 30 watts) this is OK as well but is the maximum it could power
www.gspamerica.com
Built-in Safety Measures
• Signature detection. No voltage can be applied to the cable until a compatible PD has been detected. The classification can be detected before the device is powered up.
• Current limiting is employed to protect the PSE from overload and to quickly disable malfunctioning PDs.
• Polarity protection provided by the bridges in the PDspower input circuitry means it can safely receive power regardless of the configuration and polarity of the voltage on the cable.
• Automatic disconnection of devices is performed when the monitored current falls below a minimum level.
• Low voltages are used to protect installers from electric shock hazards. The voltage used by PoE (up to 57 volts) is high enough to be efficient but low enough to be safe.
www.gspamerica.com
Distance Concerns
300 FT300 FT
POE Switch
www.gspamerica.com
Distance Concerns
• Because of the DC low voltage POE is limited to about 300 feet.
• That can be expanded by products from a Company like Veracity USA.
• With their Outreach devices can extend the distance another 300 feet with each device.
www.gspamerica.com
Advantages
• Lower cost of installation. Only 1 cable for
power and data
• Easier to maintain. Central power supply that will typically have UPS backup
www.gspamerica.com
Closing
• Any questions: email
• 1-800-298-0470
• Connect with me on LinkedIn
• www.linkedin/in/peterbrissette