77
Nonmetallic Materials Plastics, Elastomers, Ceramics and Composites

Me 131 lecture3

Embed Size (px)

DESCRIPTION

 

Citation preview

Page 1: Me 131 lecture3

Nonmetallic Materials

Plastics, Elastomers, Ceramics and Composites

Page 2: Me 131 lecture3

WOOD

LEATHER

STONE

Page 3: Me 131 lecture3
Page 4: Me 131 lecture3

PLASTICS

Page 5: Me 131 lecture3

• Built by joining smaller molecules to produce larger molecules.

• Natural or synthetic resins or their compounds that can be molded, extruded, cast or used as thin films or coating.

• Offers low density, low tooling costs, good resistance to corrosion and chemicals, cost reduction and design versatility.

Plastics

Page 6: Me 131 lecture3

Use of Plastics

• Artificial organs

• Shatter proof glass

• Bullet proof vests

• Provide thermal insulation

• Encapsulate medicines

• Form the base material in products such as: – Shower curtains

– Contact lenses

– Clothing

Page 7: Me 131 lecture3

Molecular Structures of Plastics • Paraffin-type hydrocarbons

– Carbon and Hydrogen combine/ link together indefinitely to form very large molecules.

– Carbon and Hydrogen held together by double or triple bond.

Ethane Methane

Ethylene Acetylene

Page 8: Me 131 lecture3

Isomers

• Compounds with the same molecular formula but different structural formulas.

• Due to the difference in their crystal structures, isomers do not have the same properties.

Page 9: Me 131 lecture3

Polymerization

• Also called linking of molecules.

• Number of basic units (monomers) link together to form a large molecule (polymer) in which there is a repeated unit (mer).

• The degree of polymerization (average number of mers) ranges from 75 to 750 for most commercial plastics.

• Increase chain length = increase in toughness, creep resistance, melting temperature, melt viscosity and difficulty in processing.

Page 10: Me 131 lecture3

• Copolymers – Two different types of mers are combined into the

same addition chain, thus improving the physical and mechanical properties of new types of plastics.

• Terpolymers – Combination of three different monomers.

Page 11: Me 131 lecture3

Condensation Polymerization

• Occurs when reactive molecules combine with one another to produce a polymer and small by-product molecules like water.

Page 12: Me 131 lecture3

THERMOSETTINGS AND THERMOPLASTICS

Page 13: Me 131 lecture3
Page 14: Me 131 lecture3

Thermoplastics • Contains molecules of different lengths

therefore they do not have a definite melting point.

Different temperatures

Temperatures above melting temperature

Can be poured and cast or formed by injection molding.

Temperature where it is fully solid Material can retain its amorphous structure but with companion properties that are rubbery

Much lower temperatures Bonds become stronger and polymer is stiffer and leathery.

Below glass transition temperature Linear polymer retains its amorphous structure but becomes hard, brittle and glasslike

Page 15: Me 131 lecture3

Crystallized Thermoplastics

• Thermoplastics can partially crystallize when cooled below the melting temperature.

• Chains closely align over appreciable distances with an increase in density.

• Polymer becomes harder, less ductile and more resistant to solvents and heat.

Page 16: Me 131 lecture3

Noncrystallized Thermoplastics

• Individual molecules are bonded within by strong covalent bonds but the bonding forces between molecules are much weaker.

• To increase strength, focus on restricting intermolecular slippage.

Page 17: Me 131 lecture3

4 Most Common Thermoplastics

1. Polyethylene (PE)

2. Polypropylene (PP)

3. Polystyrene (PS)

4. Polyvinyl chloride (PVC)

Page 18: Me 131 lecture3

Thermosets

• Three dimensional framework in which all atoms are connected by strong covalent bonds.

• Produced by condensation polymerization where elevated temperature promotes irreversible reaction.

• ONCE SET, subsequent heating WILL NOT produce the softening observed with the thermoplastics.

Page 19: Me 131 lecture3

• Stronger and more rigid than thermoplastics.

• Can resist higher temperatures and have greater dimensional stability.

• Lower ductility and poorer impact properties.

Page 20: Me 131 lecture3

COMMON TYPES OR FAMILIES OF PLASTICS

Thermoplastics and Thermosetting Plastics

Page 21: Me 131 lecture3

ABS Low weight, good strength and very tough; resists heat, weather and chemicals; dimensionally stable but flammable

Acrylics Common name: LUCITE and PLEXIGLAS; high-impact, flexural, tensile and dielectric strengths

Cellulose acetate Good insulating qualities, easily molded, high moisture absorption in most grades

Cellulose acetate butyrate Higher impact strength and moisture resistance; will withstand rougher usage

Ethyl cellulose High electric resistance and impact strength; retains toughness at low temperatures

Thermoplastics

Page 22: Me 131 lecture3

Fluorocarbons Inert to most chemicals, high temperature resistance, very low coefficients of friction (Teflon)

Nylon (polyamides) Low coefficient of friction, good strength, abrasion resistance and toughness, excellent dimensional stability, good heat resistance

Polycarbonates High strength and outstanding toughness, good dimensional stability, transparent or easily colored

Polyethylenes Inexpensive, tough, good chemical resistance to acids , bases and salts; high electrical resistance, low strength, easy to shape and join; reasonably clear in thin-film form LDPE HDPE UHMW

Page 23: Me 131 lecture3

PMMA(polymethyl methacrylate) Hard, brittle at room temperature, transparent or easily colored

Polypropylene Inexpensive, stronger, stiffer and better heat resistance than polyethylene; transparent

Polystyrenes High dimensional stability and stiffness with low water absorption; best all around dielectric; clear, hard and brittle at room temperature; burns readily; softens at about 95%

Polyvinyl chloride (PVC) General-purpose thermoplastic; good for outside applications; easily molded/ extruded; used with fillers, plasticizers and pigments

Vinyls Tear resistant; good aging properties; good dimensional stability and water resistance in rigid forms

Page 24: Me 131 lecture3

Thermosets

Epoxies Good strength, toughness, elasticity, chemical resistance, moisture resistance and dimensional stability; easily compounded to cure at room temperature; used as adhesives, bonding agents, coating and in fiber laminates

Melamines Excellent resistance to heat, water and many chemicals; used extensively in treating paper and cloth to impart water-repellant properties

Phenolics Oldest of the plastics; hard, strong, low cost and easily molded but rather brittle; resistant to heat and moisture

Page 25: Me 131 lecture3

Polyesters Strong and good resistance to environmental influences

Silicones Heat and weather resistant; low moisture absorption; chemically inert; excellent sealants

Urea-formaldehyde Properties similar with phenolics but available in lighter colors.

Page 26: Me 131 lecture3

PROPERTIES OF PLASTICS

Page 27: Me 131 lecture3

• Light weight

• Corrosion resistant

• Electrical resistance

• Low thermal conductivity

• Variety of optical properties

• Formability or ease of fabrication

• Surface finish

• Comparatively low cost

• Low energy content

Page 28: Me 131 lecture3

ADDITIVE AGENTS IN PLASTICS

Page 29: Me 131 lecture3

Additive Agents in Plastics

1. Impart or improve properties

2. Reduce cost

3. Improve moldability/ ease in fabrication

4. Impart color

Page 30: Me 131 lecture3

Additives

• Fillers and reinforcements

• Plasticizers

• Lubricants

• Coloring agents

• Stabilizers

• Antioxidants

• Flame retardants

Page 31: Me 131 lecture3

Fillers

• Improve strength, stiffness or toughness

• Reduce shrinkage

• Reduce weight

• Serves as an extender

• Provides cost-saving bulk

Page 32: Me 131 lecture3

Most Common Fillers

Wood Flour General purpose filler; low cost with fair strength; good moldability

Cloth Fibers Improved impact strength; fair moldability

Macerated Cloth High impact strength; limited moldability

Glass fibers High strength; dimensional stability; translucent

Mica Excellent electrical properties and low moisture absorption

Calcium carbonate, silica, talc and clay Serve primarily as extenders

Page 33: Me 131 lecture3

Coloring Agents

• Dyes or insoluble pigments which impart color to the plastics.

Dyes – for transparent plastics

Pigments – for opaque

• Optical brighteners

• Carbon black

Page 34: Me 131 lecture3

Plasticizers

• Reduce viscosity

• Improve flow of the plastic during molding

• Increase flexibility of thermoplastic products

• Used for molding purposes

Page 35: Me 131 lecture3

Lubricant

• Waxes and soap

• Improve moldability of plastics

• Facilitate removal of parts from the mold

• Used to keep thin polymer sheets from sticking to each other when stacked or rolled

Page 36: Me 131 lecture3

Other Additives

• Stabilizers and Antioxidants – Added to retard the degrading effect

of heat, light and oxidants.

• Flame Retardants – Added when nonflammability is

important

• Antistatic Agents – Allow migration of electrical

chargeand may be incorporated into plastics used for applications such as electronics packaging.

Page 37: Me 131 lecture3

• Antimicrobial additives

– Provide long-term protection from both fungus and bacteria

• Fibers

– Increase strength and stiffness

– Can modify electrical and magnetic properties

Page 38: Me 131 lecture3

Oriented Plastics

• Plastics that undergoes orientation process.

• Orientation Process

– Process that aligns molecules parallel to the applied load.

– Give long –chain thermoplastics high strength in a given direction

– Sretching, rolling or extrusion

– Increase the tensile strength by more than 50 % but a 25% increase is more typical.

Page 39: Me 131 lecture3

Engineering Plastics

• Group of plastics that has been developed with:

– improved thermal properties (up to 350C or 650F)

– enhanced impact and stress resistance

– High rigidity

– Superior electrical characteristics excellent in processing properties and little dimensional change with varying temperatures and humidity

Page 40: Me 131 lecture3

Engineering Plastics

• Polyamides • Polyacctals • Polyacrylates • Polycarbonates • Modified polyphenylene oxides • Polybutylene terephtalates • Polyketones • Polysulfones • Polyetherimides • Liquid crystal polymers

Page 41: Me 131 lecture3

Plastic Adhesive

• For bonding of dissimilar materials (metals to nonmetals)

• Involves consideration of the manufacturing conditions, the substrates to be bonded, the end-use environment and cost 1. Epoxies 2. Urethane 3. Cyanoacrylates 4. Acrylics 5. Annaerobics 6. Hot melts 7. Silicones

Page 42: Me 131 lecture3

Plastic for Tooling

• For applications where pressures, temperatures and wear requirements are not extreme.

• Costs can be reduced and smaller quantities of products can be economically justified.

• Can be produced in a much shorter time, enabling quicker production.

Page 43: Me 131 lecture3

Foamed Plastics

• Extremely versatile with properties ranging from soft and flexible to hard and rigid.

• Generally used for cushioning in upholstery and automobile seats and in various applications such as vibration absorbers.

• Semirigid foams find use in floatation devices, refigerator insulation, disposable food trays and containers, building insulation panels and sound attenuation

• Rigid foams have been used as construction materials for boats airplane components, electronic encapsulation and furniture.

Page 44: Me 131 lecture3

Polymer Coatings

• Enhance appearance

• Provide corrosion protection

• Replaces chromes and cadmiums due to environmental concerns relating to the heavy metals.

Page 45: Me 131 lecture3

Plastic vs Other Materials

• Glass containers – plastic containers

• PVC pipes and fittings – copper and brass in plumbing applications 1. Ability to be fabricated with lower tooling costs

2. Ability to be molded at the same rate as product assembly, reducing inventory

3. Possible reduction in assembly operations and easier assembly through snap fits, friction weld or the use of self-tapping fasteners

4. Ability to reuse manufacturing scrap

5. Reduced finishing costs

Page 46: Me 131 lecture3

Metals

• Cheaper and offer faster fabrication speeds

• Greater impact resistance

• Stronger and more rigid

• Can withstand paint cure temperatures

• Resistance to flames, acids and various solvents

Page 47: Me 131 lecture3

ELASTOMERS

Page 48: Me 131 lecture3

Elastomers

• Elastic polymer

• Display an exceptionally large amount of elastic deformation when a force is applied.

Page 49: Me 131 lecture3

Elastomeric Polymers

Applied force stretches the polymer by uncoiling

Remove load molecules recoil

Page 50: Me 131 lecture3

Cross-linking

Linking coiled molecules to one another by strong covalent bonds.

• Small amount soft and flexible elastomers

• Additional amount harder, stiffer and more brittle

Page 51: Me 131 lecture3

Under constant strain

STRESS-RELAXATION

Page 52: Me 131 lecture3

Rubber

• Outstanding for their: – Flexibility

– Electrical insulation

– Low internal friction

– Resistance to most inorganic acids, salts and alkalis.

• However – Poor resistance to petroleum products such as

oil, gasoline and naphtha.

– Lose their strength at elevated temperatures. (80°C or 175°F)

Page 53: Me 131 lecture3

As an engineering material

1839

Charles Goodyear

Page 54: Me 131 lecture3

Rubber

Soft Gummy Extremely

Hard

Page 55: Me 131 lecture3

Artificial Elastomers

Polyisoprene Synthetic that is closest to duplicating natural rubber

Styrene-butadiene Oil-derivative, high volume substitutefor natural rubber. (passenger-car tires)

Neoprenes With properties similar to natural rubber but with better resistance to oils, ozone, oxidation and flame. (automotive hoses and belts, footwear, tires, mounting cushions and seals)

Silicone rubbers Based on linear chain of silicon and oxygen atoms

Page 56: Me 131 lecture3

Selection of an Elastomer

• Shock absorption

• Noise and vibration control

• Corrosion protection

• Abrasion protection

• Friction modification

• Electrical and thermal insulation

• Waterproofing

Page 57: Me 131 lecture3

Considerations

• Mechanical and physical service requirements

• Operating environment

• Desired lifetime

• Ability to manufacture the product

• Cost

Page 58: Me 131 lecture3

Elastomers for Tooling Application

• Can be compounded to range from very soft to very hard.

• Hold up well under compressive loading

• Impervious to oils, solvents and other similar fluids

• Can be made into desired shape quickly

Page 59: Me 131 lecture3

CERAMICS

Page 60: Me 131 lecture3

Properties

– High temperature usage

– Hard and brittle

– High melting point

– Low thermal expansion

– Good creep resistance

– High compressive strength

Page 61: Me 131 lecture3

Nature and Structure of Ceramics

• Compounds of metallic and nonmetallic elements

• Primary bonds have high strength

– High melting temperatures

– High rigidity

– High compressive strength

• Noncrystalline structures are possible

– Amorphous condition is observed in glasses

• Both crystalline and noncrystalline ceramics are brittle

• Clay and whiteware are commonly used ceramics

Page 62: Me 131 lecture3

Special Ceramics • Refractory materials

– Ceramics that have been designed to provide mechanical or chemical properties at high temperatures

– Three categories • Acidic, basic, and neutral

• Abrasives – Ceramics have high hardness – Can be used in grinding applications – Diamond and cubic boron nitride are superabrasives

• Ceramics may be used for electrical and magnetic applications – Dielectric, piezoelectric, and ferroelectric properties

Page 63: Me 131 lecture3

Special Ceramics

• Glasses

– Soft and moldable when hot; easily shaped

– Strong in compression but brittle and weak in tension

– Excellent corrosion resistance

• Cermets are combinations of metals and ceramics

– Crucibles, nozzles, aircraft brakes

• Cements

– Plaster of paris

• Ceramic coatings

– Enamels, porcelains, glazes

Page 64: Me 131 lecture3

Ceramics for Mechanical Applications

• Ceramics have strong ionic or covalent bonds

– Most ceramics have small cracks, pores, and impurities

– Act as mechanical stress concentration points

• Advanced ceramics

– Alumina

– Silicon carbide

– Sialon

– Zirconia

• Advanced ceramics may be used as cutting tools

Page 65: Me 131 lecture3

Advanced Ceramics

Figure 8-8 Gas-turbine rotors made of silicon nitride. The lightweight material (one-half the weight of stainless steel) offers strength at elevated temperature as well as excellent resistance to corrosion and thermal shock. (Courtesy of Wesgo Division, GTE, Hayward, CA.)

Figure 8-9 A variety of components manufactured from silicon nitride, including an exhaust valve and turbine blade. (Courtesy of Wesgo Division, GTE, Hayward, CA.)

Page 66: Me 131 lecture3

COMPOSITE MATERIALS

Page 67: Me 131 lecture3

Composite Materials

• Nonuniform solid consisting of two or more different materials

– Mechanically or metallurgically bonded

– Each of the constituent materials maintains its identity

• Properties depend on:

– Properties of individual components

– Relative amounts

– Size, shape, and distribution

– Orientation

– Degree of bonding

Page 68: Me 131 lecture3

Laminar or Layered Composites • Distinct layers of

materials

• Layers are bonded together

• Typical example is plywood

• Bimetallic strips have two metals with different coefficients of thermal expansion

• Sandwich materials

Page 69: Me 131 lecture3

Particular Composites

• Consist of discrete particles of one material in a matrix of another material – Concrete

• Dispersion strengthened materials have a small amount of hard, brittle particles in a soft, metal matrix

• True particulate composites have large amount of coarse particles

• Metal-matrix composites

Page 70: Me 131 lecture3

Fiber-Reinforced Composites

• Discontinuous thin fibers of one material are embedded in a matrix – Wood and bamboo are naturally occurring fiber composites – Bricks of straw and mud – Automobile tires

• Fibers of nylon, rayon, Kevlar, or steel to reinforce the rubber

– Glass fibers – Graphite – Ceramic fibers, metal wires, whiskers

• Common objective is high strength and lightweight – Orientation of the fibers is important

Page 71: Me 131 lecture3

Properties of Fiber-Reinforced Composites

• Advanced fiber-reinforced composites – Organic or resin matrix composites

• Sports equipment, light-weight armor, low-temperature aerospace applications

• have a maximum service temperature of about 315ºC (600ºF)

– Metal-matrix composites

• Nonflammable, do not absorb water or gases, corrosion resistance

• operating temperatures up to 1250ºC (2300ºF), where the conditions require high strength, high stiffness, good electrical and/or thermal conductivity, exceptional wear resistance, and good ductility and toughness

Page 72: Me 131 lecture3

Properties of Fiber-Reinforced Composites

– Carbon-carbon composites

• High temperature applications • operate at temperatures above 2000ºC (3600ºF), along

with a strength that is 20 times that of conventional graphite, a density that is 30% lighter

– Ceramic-matrix composites

• High temperature strength, stiffness, and environmental stability

• operate at temperatures as high as 1500ºC (2700ºF)

Page 73: Me 131 lecture3

Composites

• Hybrid composites

– Two or more fibers

• Alternate layers of fibers

• Mixed strands in the same layer

• Combination of mixed strands and alternating layers

• Selected placements

• Fibers are stitched together

Page 74: Me 131 lecture3

Design and Fabrication

• Select the component materials

• Determine the relative amounts of each component

• Determine the size, shape, distribution, and orientation

• Select the proper fabrication method

– Compression molding

– Filament winding

– Pultrusion

– Cloth lamination

• Composites may be tailored to specific applications

Page 75: Me 131 lecture3

Practical Applications

• Manufacturing with composites is labor intensive

• Defects

– Delamination voids

– Missing layers

– Contamination

– Fiber breakage

– Improperly cured resin

• Areas of application

– Aerospace

– Sporting equipment

– Automobiles

– Boat hulls

– Pipes

Page 76: Me 131 lecture3

Areas of Application

Figure 8-14 Composite materials are often used in sporting goods to improve performance through light weight, high stiffness, and high strength, and also to provide attractive styling. (Left) A composite material snowboard; (right) composites being used in a fishing rod, water ski, and tennis racquet.

Page 77: Me 131 lecture3

Summary

• Plastics, ceramics, and composites are nonmetallic materials that are commonly used.

• Additives are used in plastics to produce desired properties

• Composite’s properties depend on the way in which the materials are combined and their orientation

• Ceramics are ideal for high temperature applications