43
1 The Indexing or Dividing Head Session 14

Indexing or dividing_head

Embed Size (px)

DESCRIPTION

 

Citation preview

Page 1: Indexing or dividing_head

1

The Indexing or Dividing Head

Session 14

Page 2: Indexing or dividing_head

2

Indexing (Dividing) Head• Once one of the more important

attachments for milling machine

• Used to divide circumference of workpiece into equally spaced divisions when milling gear teeth, squares, hexagons, and octagons

• Also used to rotate workpiece at predetermined ratio to table feed rate

Page 3: Indexing or dividing_head

3

Index Head Parts

• Headstock with index plates• Headstock change gears• Quadrant

• Universal chuck• Footstock• Center rest

Page 4: Indexing or dividing_head

4

Index Head Parts• Swiveling block

• Mounted in base enables headstock to be tilted from 5º below horizontal to 10º beyond vertical

• Spindle• Mounted in swiveling block with 40-tooth

worm wheel, meshes with worm• Worm

• Right angle to spindle, connected to index crank

• Direct indexing plate• Engaged by pin and attached to front of

spindle

Page 5: Indexing or dividing_head

5

Index Head Parts

Page 6: Indexing or dividing_head

6

Section view of a dividing head

Page 7: Indexing or dividing_head

7

Index Head Parts• Universal chuck

• Threaded onto end of spindle

Page 8: Indexing or dividing_head

8

Index Head Parts• Footstock

• Used in conjunction with headstock to support work held between centers or in chuck

• May be adjusted longitudinally, raised or lowered off center, and tilted out of parallel

Page 9: Indexing or dividing_head

9

Index Head PartsAdjustable center rest

• Holds long, slender work between centers

Page 10: Indexing or dividing_head

10

Methods of Indexing

1. Direct

2. Simple

3. Angular

4. Differential

Page 11: Indexing or dividing_head

11

Direct Indexing

• Simplest form of indexing• Performed by disengaging worm shaft

from worm wheel by means of eccentric device in dividing head• Spring-loaded tongue lock engages

numbered slots in index plate

• Used for quick indexing of workpiece when cutting flutes, hexagons, squares, etc.

Page 12: Indexing or dividing_head

12

Direct Indexing Divisions• Direct indexing plate usually contains three

sets of hole circles or slots: 24, 30, and 36• Number of divisions possible to index limited

to numbers that are factors of 24, 30, 36

Slots Direct indexing divisions

24 2 3 4 _ 6 8 _ __ 12 __ __ 24 __ __

30 2 3 _ 5 6 _ _ 10 __ 15 __ __ 30 __

36 2 3 4 _ 6 _ 9 __ 12 __ 18 __ __ 36

Page 13: Indexing or dividing_head

13

Example: Direct Indexing

• What direct indexing is necessary to mill eight flutes on a reamer blank?

Slots Direct indexing divisions

24 2 3 4 _ 6 8 _ __ 12 __ __ 24 __ __

30 2 3 _ 5 6 _ _ 10 __ 15 __ __ 30 __

36 2 3 4 _ 6 _ 9 __ 12 __ 18 __ __ 36

Since the 24-hole circle is the only one divisible by 8 (the required number of divisions), it is the only circle that can be used in this case.

Never count the hole or slot in which the index pin is engaged.

Page 14: Indexing or dividing_head

14

Milling a Square with Direct Indexing

1. Disengage worm and worm shaft by turning worm disengaging shaft lever if dividing head is so equipped

2. Adjust plunger behind index plate into the 24-hole circle or slot

3. Mount workpiece in dividing head chuck or between centers

4. Adjust cutter height and cut first side

Page 15: Indexing or dividing_head

15

5. Remove plunger pin using plunger pin lever

6. Turn plate attached to dividing head spindle one-half turn and engage plunger pin

7. Take second cut

Milling a Square with Direct Indexing

Page 16: Indexing or dividing_head

16

8. Measure work across flats and adjust work height if required

9. Cut remaining sides by indexing every six holes until all surfaces cut

10.Check for finish size

Milling a Square with Direct Indexing

Page 17: Indexing or dividing_head

17

Simple Indexing

• Work positioned by means of crank, index plate, and sector arms

• Worm attached to crank must be engaged with worm wheel on dividing head spindle• 40 teeth on worm wheel • One complete turn on index crank cause

spindle and work to rotate one-fortieth of a turn (ratio of 40:1)

Page 18: Indexing or dividing_head

18

Simple Indexing

• Calculating the indexing or number of turns of crank for most divisions, simply divide 40 by number of divisions to be cut or,

40Indexing =

N

Page 19: Indexing or dividing_head

19

Simple Indexing

• The indexing required to cut eight flutes:

crankindex of turns full 58

40

• The indexing required to cut seven flutes:

crankindex of turns 7

55

7

40

The five-sevenths turn involves use of an index plate and sector arms.

Page 20: Indexing or dividing_head

20

Index Plate and Sector Arms

• Index plate• Circular plate provided with series of

equally spaced holes into which index crank pin engages

• Sector arms• Fit on front of plate and may be set to any

portion of a complete turn

Page 21: Indexing or dividing_head

21

Finishing Indexing for Seven Flutes

Index-plate hole circlesBrown & Sharpe

Plate 1 15-16-17-18-19-20

Plate 2 21-23-27-29-31-33

Plate 3 37-39-41-43-47-49

Cincinnati Standard Plate

One side 24-25-28-30-34-37-38-39-41-42-43

Other side 46-47-49-51-53-54-57-58-59-62-66

Choose any hole circle that is divisible

by denominator 7

5/7 = /21

So, 5 full turns plus15 holes on 21 holecircle!

15

Page 22: Indexing or dividing_head

22

Finishing Indexing for Seven Flutes

Index-plate hole circlesBrown & Sharpe

Plate 1 15-16-17-18-19-20

Plate 2 21-23-27-29-31-33

Plate 3 37-39-41-43-47-49

Cincinnati Standard Plate

One side 24-25-28-30-34-37-38-39-41-42-43

Other side 46-47-49-51-53-54-57-58-59-62-66

Choose any hole circle that is divisible

by denominator 7

5/7 = /49

So, 5 full turns plus35 holes on 49 holecircle!

35

Page 23: Indexing or dividing_head

23

Finishing Indexing for Seven Flutes

Index-plate hole circlesBrown & Sharpe

Plate 1 15-16-17-18-19-20

Plate 2 21-23-27-29-31-33

Plate 3 37-39-41-43-47-49

Cincinnati Standard Plate

One side 24-25-28-30-34-37-38-39-41-42-43

Other side 46-47-49-51-53-54-57-58-59-62-66

Choose any hole circle that is divisible

by denominator 7

5/7 = /28

So, 5 full turns plus20 holes on 28 holecircle!

20

Page 24: Indexing or dividing_head

24

Finishing Indexing for Seven Flutes

Index-plate hole circlesBrown & Sharpe

Plate 1 15-16-17-18-19-20

Plate 2 21-23-27-29-31-33

Plate 3 37-39-41-43-47-49

Cincinnati Standard Plate

One side 24-25-28-30-34-37-38-39-41-42-43

Other side 46-47-49-51-53-54-57-58-59-62-66

Choose any hole circle that is divisible

by denominator 7

5/7 = /42

So, 5 full turns plus30 holes on 42 holecircle!

30

Page 25: Indexing or dividing_head

25

Finishing Indexing for Seven Flutes

Index-plate hole circlesBrown & Sharpe

Plate 1 15-16-17-18-19-20

Plate 2 21-23-27-29-31-33

Plate 3 37-39-41-43-47-49

Cincinnati Standard Plate

One side 24-25-28-30-34-37-38-39-41-42-43

Other side 46-47-49-51-53-54-57-58-59-62-66

Choose any hole circle that is divisible

by denominator 7

5/7 = /49

So, 5 full turns plus35 holes on 49 holecircle!

35

Page 26: Indexing or dividing_head

26

Cutting Seven Flutes

1. Mount B&S Plate 2 index plate on dividing head

2. Loosen index crank nut and set index pin into hole on 21-hole circle

3. Tighten index crank nut and check to see that the pin enters hole easily

4. Loosen setscrew on sector arm5. Place narrow edge of left arm against

index pin

Page 27: Indexing or dividing_head

27

6. Count 15 holes on 21-hole circle• Do not include hole in which index crank

pin is engaged.

7. Move right sector arm slightly beyond fifteenth hole and tighten sector arm setscrew

8. Align cutter with work piece

9. Start machine and set cutter to top of work by using paper feeler

Cutting Seven Flutes

Page 28: Indexing or dividing_head

28

10.Move table so cutter clears end of work

11.Tighten friction lock on dividing head before making each cut and loosen lock when indexing for spaces

12.Set depth of cut and take first cut

13.After first flute has been cut, return table to original starting position

Cutting Seven Flutes

Page 29: Indexing or dividing_head

29

14.Withdraw index pin and turn crank clockwise five full turns plus the 15 holes indicated right sector arm

• Release index pin between 14th and 15th holes and gently tap until it drops into 15th hole

15.Turn sector arm farthest from pin clockwise until it is against index pin

Cutting Seven Flutes

Page 30: Indexing or dividing_head

30

16.Lock dividing head; continue machining and indexing for remaining flutes

Cutting Seven Flutes

The arm farthest from the pin is held and turned. If the arm next to the pin were held and turned, the spacing between both sector arms could be increased when the other arm hits the pin. This could result in an indexing error not noticeable until the work was completed.

Page 31: Indexing or dividing_head

31

Angular Indexing

• Setup for simple indexing may be used• Must calculate indexing with angular

distance between divisions instead number of divisions

• One complete turn of index crank turns work 1/40 of a turn• 1/40 of 360º equals 9 degrees

9

required degrees of no. degrees in Indexing

Page 32: Indexing or dividing_head

32

Angular Indexing

Calculate indexing for 45º

59

45 Indexing

5 complete turns

Page 33: Indexing or dividing_head

33

Angular Indexing

Calculate indexing for 60º

3

26

9

60 Indexing

6 full turns plus 12 holes on 18 hole circle

Page 34: Indexing or dividing_head

34

Angular Indexing

Calculate indexing for 24'

Divide 24'/540' = 4/90 4/90 = 1/22.5

1 hole on a 22.5 hole circle

The nearest is a 23 hole circle. Indexing would be 1 hole on a 23 hole circle with a slight error (approximately 1/2 minute). A need for higher accuracy requires differential indexing.

Page 35: Indexing or dividing_head

35

Angular Indexing

Calculate indexing for 24º30'• First, convert angle into minutes

(24 x 60') = 1440' now add 30' = 1470'Convert 9° to minutes 9°x60 = 540'

Divide 1470'/540' = 2 13/18

2 full turns and 13 holes on 18 hole circle

Page 36: Indexing or dividing_head

44

Wide-Range Dividing Head• Possible for 2 to 400,000 divisions• Large index plate contains 11 hole

circles on each side• Small index plate mounted in front of

large, contains a 54 hole and a 100-hole circle

• 40:1 ratio between worm and dividing head spindle

Page 37: Indexing or dividing_head

45

A – large index plate

B - crank

C – small index plate

D - crank G – gear housing

Page 38: Indexing or dividing_head

46

Indexing for Divisions

• One turn of small crank drives index head spindle 1/100 of 1/40, or 1/4000 of a turn• Ratio of large index crank to dividing head

40:1• Ratio of small index crank 100:1

Page 39: Indexing or dividing_head

47

Indexing for Divisions

• One hole on 100-hole circle of small index plate C = 1/100 x 1/4000 • 1/400,000 of a turn

• Formula for indexing divisions = 400,000/N

Page 40: Indexing or dividing_head

48

Indexing for Divisions

No. of turns of large index crank

No. of holes on 100-hole circle of large plate

No. of holes on 100-hole circle of small plate

4 0  0 0  0 04 04 0  0 0

NNumber of Divisions

x x

Page 41: Indexing or dividing_head

49

Indexing for Divisions

For 1250 divisions 400000/1250

40|00|00 1250

Since ratio of large index crank is 40:1 , any number that divides into 40 (first two numbers) represents full turns of large index crank

No. of turnsof large Index Crank = 0

One hole on 100-holecircle produces 1/4000of a turn; any numberdivides into 4000 are

indexed on large plate

20

No. turns100-hole=Large plate

3 20 holes on the 100-hole circle

small plate

4 0  0 0  0 04 04 0  0 0

N

30

Zero turns of large crank, 3 turns of 100-hole large plate and 20 holes on 100-hole small plate

Page 42: Indexing or dividing_head

50

Angular Indexing with the Wide-Range Divider

• Indexing in degrees, minutes, and seconds easily accomplished

• Both large and small index cranks set on 54-hole circle of each plate• Each space on 54-hole large plate will

cause dividing head spindle to rotate 10'• Each space on 54-hole small plate will

cause work to rotate 6"

Page 43: Indexing or dividing_head

51

Angular Indexing: cont.

plate) small on (indexed 6

N Seconds

plate) large on (indexed 10

N Minutes

plate) large on (indexed9

N Degrees

Example: Index for an angle of 17º36'18"

turns 9

81

9

17

One full turn + 48 holes on large plate

6' of r with3 10

36

3 holes on large plate

636

378

6

18x60)(6'

One full turn + 9 holes on small plate

One full turn + 51 holes on large plate