Conveyor Safety:The Basics

Stay Safe

As with any equipment found in your plant, conveyors pose a safety concern for your employees. Improper usage, poor training, and lack of safety procedures contribute to employee injuries

around conveying systems.

The Conveyor Equipment Manufacturers Association (CEMA) has established 12 safety standards for bulk handling conveyors. Following these standards should be the starting point for

your conveyor safety training.

Do not climb, sit, standwalk, ride, or touch the conveyor at any time.

It seems self explanatory, and almost not worth mentioning, but monkeying around on or near a conveyor is a recipe for injury. Climbing, sitting, walking, riding, or touching the conveyor, especially when in use, not only can cause injury to your employees, but can damage your conveyor as well.

#1

Do not perform maintenance on a conveyor until electrical, air, hydraulic and gravity energy sources have been locked out and blocked.Proper lock-out, tag-out procedures should be followed before any maintenance is performed on your conveyor. Sometimes technicians get too confident in their ability to perform maintenance procedures on a conveyor without going through the process of locking out all electrical and other energy sources. One miscalculation could result in serious injury or death. Always lock-out, tag-out before performing any maintenance on your conveyor.

#2

Operate equipment onlywith all approved coversand guards in place.

The manufacturer provides covers and guards for employee safety - and protect you from components and points that pose the highest risk of injury. Ensuring all cover and guards are in place before operating the conveyor is for your safety.

#3

Lock out all power and block gravity loadsbefore servicing.

In similar fashion with performing maintenance on a conveyor, follow all lock-out, tag-out procedures before servicing any part of the conveyor. Failure to do so may cause the conveyor to start up while technicians are in dangerous positions in, around, or under the conveyor.

#4

Ensure that all personnelare clear of equipmentbefore starting.

Always be sure that everyone is clear of the conveyor before starting it up. Many factories install warning horns to alert employees when the conveyor is about to become active. While a great and inexpensive upgrade, it is beneficial to train employees to make sure everyone is clear.

#5

Allow only authorized and trained personnel to operateor maintain conveyor.

Proper training on the operation and maintenance of a conveyor is essential for employee safety. Allowing unauthorized or untrained personnel to use or maintain the conveyor often results in injury. There are two reasons for this:• The safety of your technician• Only trained and authorized personnel know how to properly maintain

a conveyor to operate at peak efficiency.

#6

Keep clothing, body partsand hair away from conveyors.

Clothing, body parts, and hair can easily get caught in the moving parts of a conveyor, and lead to serious injury or death. Workers should keep all hands clear of the conveyor. Loose hair and clothing should be tied back to keep it clear of moving parts. Ties should be secured over the shoulder or tucked in. Long sleeves should be rolled up. These simple rules can be the difference between safety and injury.

#7

Clean up spillage around tail pulleys,Idlers, and load points only whenPower is locked out and guards are in place.It's important to keep the area around your conveyor clean and free of debris and liquid. However, cleaning should never be done with the conveyor is powered and operational. Doing so can result in serious injury. Follow all lock-out, tag-out procedures before cleaning around a conveyor.

#8

Do not modify or misuse conveyorcontrols.

Conveyor controls go beyond a simple on / off switch. They include the controls necessary for the safe operation of your conveyor. Under no circumstances should the controls be modified or altered by any unauthorized personnel.

#9

Ensure that all controlsand pull cords arevisible and accessible.

In the case that a conveyor needs to be stopped for an emergency, all controls and pull cords should be easily accessible and visible so anyone working in the area can reach them.

#10

Do not modify or remove controls,guards, interlocks, warnings or other safety items withoutmanufacturer’s approval.The manufacturer includes controls, guards, interlocks, warnings and other safety items for a reason. If those items are included on your conveyor, it's because the manufacturer has located a safety risk in that area of the equipment. Removing those items without the manufacturer's approval not only puts your employees at risk, it likely will void any warranty you have on the equipment.

#11

Report all unsafeConditions.Create a culture within your plant where employees report all unsafe conditions to the proper personnel. Doing so will allow the proper steps to be taken to clear up unsafe conditions and reduce the risk of employee injuries.

#12

Download the Poster

Following the CEMA's twelve standards will keep your employees safe around a bulk handling conveyor. You can download a poster with these safety standards, as well as images,

on the CEMA's website by clicking the button below.

Download Poster

About Fusion Tech

About Fusion Tech Fusion Tech Integrated, Inc. is a custom metal fabrication company with 15 years of experience and expertise in creating steel solutions for a variety of clients in the food processing, pharmaceutical, transportation, mining, renewable energy, and agricultural industries.

We specialize in providing innovative solutions for the food processing industry.

Click to Visit Our Website

218 20th AvenueRoseville, IL 61473

t. 309.774.4275f. 309.774.4161

600 Stevens Port Dr, Ste 112Dakota Dunes, SD 57049

t. 605.242.6070f. 605.217.6001