View
3.261
Download
1
Category
Preview:
DESCRIPTION
EDM Activation of RTP Components I http://wp.me/p1Ci5j-3n
Citation preview
ISU EDM: Activation of RTP Component
– I
This post is about the 3 types of activation possible for RTP Component in the RTP
Interface. The types are
1. Use and Activate Generally
2. Use and Activate Individually
3. Use Individually and Activate Generally.
More information on them can be obtained here. Anyways I am pasting the info here.
* Use and activate generally (activation and definition for all installations)
This activity type means that you must activate the RTP component at RTP interface level
and that you define the parameter allocation for the input parameters at RTP interface level.
* Use and activate individually (activation and definition for individual installations)
This activation type enables you to activate the RTP component only at installation level, not
at RTP interface level.
You can define the parameter allocations for the input parameters in the following ways:-
->Define the parameter allocation at RTP interface level
->Define parameter templates at RTP interface level. You can then define parameter
allocations for the input parameters at installation level based on these parameter templates.
* Use individually and activate generally (activation for all installations and for individual
installations)
This activation type means that you must activate the RTP component both at RTP interface
level and at installation level.
You can define the parameter allocations for the input parameters in the following ways:-
->Define the parameter allocation at RTP interface level
->Define parameter templates at RTP interface level. You can then define parameter
allocations for the input parameters at installation level based on these parameter templates.
Now most of the time we were using the first Activation Type ‘Use and Activate Generally’
.So we were activating the RTP Component at the Interface level and also assigning the
input/output parameters in the same.
If we use the rest two activation types there is not much difference ,only thing is that , that we
could activate the RTP Component at the installation level and also probably assign input
parameters at the installation level.
In case of RTP Components with Activation Type ‘Use and Activate Individually‘ and ‘Use
Individually and Activate Generally‘ we can assign the profiles or roles to the input
parameters at the installation level.(assigning at the RTP Interface level is still possible but
with the activation type we intend to use ,it would act like the same as the first activation type
and won’t be for individual installations).For assigning at the Installation level we use
Parameter Templates which are automatically proposed during maintenance at installation
level.
This time there is no presentation but just pasting the screenshots here.
First we look at the RTP Interface in which the component has the Activation Type as ‘Use
and Activate Individually‘.
rtp interface for use & activate individually actiavtion type
Here we can see that with Activation Type ‘Use and Activate Individually‘ if we try to
Activate it at the RTP Interface level it gives an Error. We have to activate this at the
Installation level only. We will now try to assign an input parameter to a Parameter
Template so that we can assign the input parameter at the Installation level.
To assign an input parameter to a parameter template click on the input parameter then go to
tab ‘Parameter temp.’ click on the checkbox for ‘Template required’ and press ‘Copy’. The
traffic light for the input parameter will change from Red to Yellow.
Now in the Installation click on ‘RTP Interface’ we see the below screen. Goto the tab
‘Component’ and select the checkbox ‘Activate’ and press ‘Copy’. So now the RTP
Component has been activated for the Installation.
Now we need to assign the input parameter. Click on the input parameter, go to tab
‘Parameter‘ and assign the value for the parameter. It would look like this.
So this was all about Activation Type ‘Use and Activate Individually’.
Now we look at Activation Type ‘Use Individually and Activate Generally‘.
In here one has to activate the RTP Component at the RTP Interface level.
the input parameters are assigned to Parameter Templates ,so that I can assign them at an
individual level in the Installation.
Input Parameter assigned to Parameter Templates
In the Installation the input parameters are assigned values.
Input Parameter to be assigned in Installation
Input Parameters assigned values in the Installation
Billing happens the normal way.
So one can ask that why do we need to use these activation types.
Well SAP gives you the flexibility to model the use of your RTP Components depending on
Individual Installation needs depending on Individual tarrif changes or even limiting the
activation for certain times.
So instead of using the same input parameters for all the installation you can have individual
input parameters by just changing the activation type of the RTP Component and the priority
and using the Parameter Templates.
There is a very good example given in the help.sap site for this, do have a look.
Look into this link here ‘Activation of RTP Component – II’ for an example on this.
————————————————————————————–
If I have missed something above or wrote something wrong please comment and inform me.
Also if you have any suggestions or any topics you would like to know about in
EDM/IDE/AMI/DM do inform.
Recommended