Head and Eye Protection Program Essentials

Your Partners in Safety

Eye Protection Program Essentials Webinar

3M Eyewear, Head and Face Protection Products

Agenda

Introductions Chris Dujovski -- Product Marketer – Head, Eye & Face

Safety Eyewear Hazards & Hazard Analysis Safety Eyewear Selection & Styles – Face Protection Options Q & A ??

FROM…..

TO….

3M Occupational Health and Environmental Safety Division

Occupational Eye Hazards- Section 1

Not Wearing Eye Protection Nearly three out of five workers injured were not wearing eye

protection at the time of the accident. Wearing the Wrong Kind of Protection For the Job About 40% of the injured workers were wearing some form of eye

protection when the accident occurred. However these workers were most likely wearing protective eyeglasses with no side shields.

Source: 1993 OSHA Fact Sheet No. 93-03.

What Contributes to Eye Injuries at Work? A 1980 survey by the Labor’s Department’s Bureau of Labor

statistics of about 1,000 minor eye injuries revealed how and why many on the job accidents occur.

Eye Hazard Training – Module 1 Objectives

The purpose of this training is to: Help you identify the types of tasks that may require the use of

protective eyewear. (Section 1) Help you understand how the eye reacts to light. (Section 2) Provide a brief overview of the light spectrum and potential

occupational hazards. (Section 3) You will be required to go through each topic to complete this

module.

Occupational Eye Hazards

Flying Particles • Almost 70% of accidents resulted from flying or falling objects or sparks striking the eye. • Injured workers estimated that nearly three-fifths of the objects were smaller than a pinhead.

• Contact with chemicals caused one-fifth of the injuries.

What Causes Eye Injuries?

Source: 1993 OSHA Fact Sheet No. 93-03.

Eye and face protection must be selected on the basis of potential hazards to which the worker may be exposed.

How is Proper Eye and Face Protection Selected?

A first critical step in developing a comprehensive safety and health program is to identify potential physical and health hazards in the workplace. This process is known as a "hazard assessment." A properly conducted hazard assessment identifies routine and non-routine activities and tasks which have increased risk of exposure to eye and face hazards, among other types of hazards.

Hazard Assessment

The hazard assessment is the responsibility of the employer’s health and safety administrator.

In the United States, the Occupational Health and Safety Administration (OSHA) Personal Protective Equipment Standard 1910.132(d)(1) specifies employer and employee

obligations to help reduce the risk of exposure to hazards.

Hazard Assessment

A hazard assessment specific to eye and face hazards should begin with a walk-through survey of the facility to develop a list of potential eye and face hazards such as:

• Impact- Flying fragments, objects, large chips, particles, etc. • Dust- Nuisance dust • Chemical -Splash and irritating mists • Optical Radiation - Glare • Optical Radiation - Welding, cutting, torch brazing • Heat -Hot sparks, splash from molten metal • General Lighting - Fluorescent /incandescent, low light • Special Applications - Inspection, repair, detail work

Hazard Assessment (Eye Hazard Specific)

Occupational Eye Hazards - Impact Common Related Applications Tasks that may present impact hazards to the eyes and face of workers:

Chipping Drilling Grinding Riveting Crushing

Occupational Eye Hazards - Dust

Common Related Applications Tasks that may present dust hazards to the eyes and face of workers:

Woodworking Buffing Grinding General dusty conditions

Occupational Eye Hazards - Chemical

Common Related Applications Tasks that may present chemical hazards to the eyes and face of workers: Acid and chemical handling Degreasing Plating Pouring Spraying

Occupational Eye Hazards - Optical Radiation (Glare)

Working outdoors in bright sun Driving

Common Related Applications Tasks that may present optical radiation (glare) hazards to the eyes and face of workers:

Occupational Eye Hazards - Optical Radiation (Welding)

Electric arc welding Gas welding Torch brazing Torch soldering Cutting

Common Related Applications Tasks that may present optical radiation (welding) hazards to the

eyes and face of workers:

Occupational Eye Hazards - Heat Common Related Applications/Tasks Furnace operations Pouring Casting Hot dipping Gas cutting and welding

End of Topic

400-700nm Visible light range

700nm-1mm Infrared

400 nm Ultraviolet

Light Spectrum and Occupational Hazards

Ultraviolet (UV) Less than 400 nanometers (nm) Visible 400 nm to 700 nanometers Infrared (IR) Higher than 700 nanometers

Wavelengths UV to IR

Ultraviolet rays have shorter wavelengths and more energy than visible light rays and can cause acute harmful effects or chronic harmful effects, depending on the wavelength, energy level, and duration of exposure.

Ultraviolet Radiation (UV)

UVA- (320 - 400 nm) UVA rays are absorbed by the lens of your eye. Extended exposure

to UVA rays can lead to the formation of cataracts. UVB - (290 - 320 nm)

UVB is a physically painful form of ultraviolet radiation. Exposure to UVB can temporarily damage the cornea. This band of radiation causes cancer and burning of the eye and has been linked to damage of the lens inside the eye.

UVC- (200 - 290 nm) UVC emitted from the sun is absorbed by the atmospheric ozone layer and never reaches your eyes.

Ultraviolet Radiation (UV)

The sun is our primary natural source of UV radiation.

Ultraviolet Radiation – Natural Sources

Arc welding Electrical arcing Arc furnaces Ultraviolet lamps Lasers (Excimer) Certain adhesive, ink and paint curing lamps Tanning beds

Light Spectrum and Occupational Hazards Ultraviolet Radiation- Artificial Sources UV radiation can also be generated from artificial sources including:

Ultraviolet Radiation-Eyewear Protection

A polycarbonate lens is capable of filtering 99.9% UV. UV inhibitors are often added to the base polycarbonate material from which safety lenses are made.

Visible light waves are the only electromagnetic waves we can see. We see these waves as the colors of the rainbow. Each color has a different wavelength. Red has the longest wavelength and violet has the shortest wavelength.

When all the waves are seen together, they make white light.

Visible Light

Visible Spectrum of Light

Long Short

When white light shines through a prism, the white light is broken apart into the colors of the visible light spectrum.

Visible Light

White Light

Visible light has a band from 400 nm to 700 nm.

Visible Light

Visible Light Range

Overexposure to visible light can cause eye strain and headaches.

Visible Light Light Spectrum and Occupational Hazards

• Sunlight • Spot lights • Flood lights • Flash lamps • High temperature furnaces • Visible Wavelength Lasers (e.g. Argon and Ruby)

Visible Light Typical Sources of Visible Radiation Include:

Visible Light

Certain gray, light blue, tan, bronze, mirror, and indoor outdoor mirror lenses are effective in helping to reducing glare from the sun and certain bright lights. Lighting conditions in the work environment and the need for

filtering of specific visible light wavelengths can dictate vision enhancement and glare reduction requirements.

The infrared light spectrum is medium to long wavelengths of light located in the upper middle to upper portion of the optical spectrum.

Infrared Radiation (IR)

Infrared Light Range

Typical industrial sources of infrared include: • Open furnaces • Molten metal operations • Heat lamps • Quartz lamps, • Electric arc welding • Gas welding

Light Spectrum and Occupational Hazards Infrared Radiation

Exposure to infrared light can heat the lens of the eye and produce cataracts over a long period of time.

Light Spectrum and Occupational Hazards Infrared Radiation

Selecting Eye and Face Protection

Non-prescription safety spectacles Prescription safety spectacles Goggles Faceshields Welding helmets

Full facepiece and loose fitting respirators

Safety Eye and Face Protection Can Include the Following:

Selecting Eye and Face Protection Safety eyewear is intended to help shield the wearer's eyes from

potential impact hazards such as flying fragments, objects, large chips, and particles.

Employees who wear prescription lenses while engaged in operations that involve exposure to potential eye hazards should wear eye protection that incorporates the prescription in its design, or wear safety glasses or goggles that fit over the prescription glasses.

Non-Prescription Safety Spectacles– Many Options!

Lenses are offered in different tints and colors for a variety of reasons, including reduction of Ultraviolet (UV) or Infrared

(IR) exposure, vision enhancement, glare reduction or style preference.

Understanding lens tints is critical in matching the appropriate

safety eyewear with the environment.

It is the employer’s responsibility to conduct a workplace hazard assessment and provide personal protective equipment that protects against the potential hazards identified.

Selecting Eye and Face Protection Why is lens color an important consideration?

A yellow tint on a lens helps make objects appear sharper against a blue or green background.

An amber lens can block the blue portion of the visible light spectrum, creating maximum contrast enhancement, particularly in low light.

Yellow tints are good for overcast, hazy or foggy conditions.

Yellow and Amber Lenses

Developed for semiconductor fabrication, photolithography and similar industries where there is medium to high levels of yellow incandescent/fluorescent lamps, or high and low pressure sodium vapor lighting.

Can be useful as a general glare reducer in certain work environments where there is strong glare from bright lighting.

Light Blue Lens

For certain outdoor applications where light and glare can cause eye strain and fatigue.

A gray tint can help provide protection from glare and can help keep distortion of colors to a minimum.

Selecting Eye and Face Protection Gray Lens

A clear lens with a slight mirror coating, it can serve the same purpose as a gray lens, yet allow more visible light through the lens for certain indoor/outdoor uses.

Can help reduce glare from certain artificial light sources. Not as dark as a normal sunglass lens and is typically used in

applications where the workers must pass between indoor and outdoor duties or where a normal sunglass lens is too dark.

Indoor/Outdoor Lens

Use the bronze/brown lens for certain outdoor applications where sunlight and glare may cause eye strain and fatigue. The bronze/brown tints work well in many variable light conditions and can provide good contrast because they filter some blue light, although not as strongly as a yellow tint.

Selecting Eye and Face Protection Bronze/Brown Lens

A mirror lens can be used outdoors where sunlight and glare may cause eye strain and fatigue. Mirror coating reflect certain light, reducing the amount of light that passes through the lens.

Selecting Eye and Face Protection Mirror Lens

The 3M TM MinimIzeR is a reduced IR lens designed specifically for work around certain shielded welding operations or under welding helmets.

This lens can help protect against some infrared radiation and “flash burn”, a common and damaging hazard that can occur when workers are exposed to welding arcs. Not designed to be worn as primary eye protection in welding, cutting, torch brazing, or torch soldering.

3M TM MinimIzeR TM (Reduced IR Lens)

When a photochromic lens is exposed to outdoor ultraviolet light, the lens automatically darkens for added protection against bright light.

The photochromic lens is useful for certain utility work, landscaping, and construction.

Selecting Eye and Face Protection Photochromic Lens

The photochromic lens should not be used in situations which require quickly moving back and forth from one “light environment” to another (such as fork lift drivers going from inside to outside).

Not for driving.

Selecting Eye and Face Protection Photochromic Lens

Can be used outdoors to help protect from excessive glare that can cause eye strain and fatigue.

Polarized lenses can help reduce the reflected glare which is most noticeable on water, snow, concrete and asphalt surfaces.

Polarized lenses contain a special filter that blocks certain reflected light, thereby reducing glare.

Selecting Eye and Face Protection Polarized Lens

The Green/I.R. Shade lens may be appropriate in certain

applications where there is heat, such as metal making, furnace work, trash incineration and open flames.

Green/I.R. Shade Lens

A clear lens can provide maximum visual acuity and color recognition.

A clear polycarbonate lens is capable of filtering out 99.9%

UV light.

Clear Lens

Section 2

Eye and Face Protection Options

Eye and Face Protection Options-Section 2

Designed to fit over many different styles of personal prescription eyewear.

Spectacles OTG (Over the Glass)

Can provide magnification for reading or precision work, while providing protection against certain impacts. Available in diopters +1.5, +2.0 and +2.5

Bifocals Safety Spectacles for Special Applications

Safety eyewear with LED (light-emitting diodes), can provide task lighting while providing protection against certain impacts.

Safety Spectacles for Special Applications

Polycarbonate • Stronger and more impact resistant than glass or plastic • Lightweight

Cast Resin (e.g., CR-39®*) • Mainly used in safety prescription spectacles

Safety Glass • Some prescription eyewear products • Special purpose lenses • More scratch resistant than polycarbonate and plastic • Heavier and less impact-resistant than plastic *CR-39® is a registered trademark of PPG industries

Selecting Eye and Face Protection Lens Materials

Softness properties of polycarbonate typically require that a scratch-resistant coating be applied to the lens by the manufacturer to improve durability.

Other coatings, such as anti-fog, can be applied to a lens to improve performance in harsh environments. Anti-fog coatings are generally not permanent and will erode after repeated cleanings.

Proper care and cleaning of an anti-fog lens, following the manufacturer’s recommendations, can help maintain coating performance.

Lens Coatings

Hard Coat (H/C) A hard coat can help provide scratch resistance to a polycarbonate,

lens which typically scratches very easily without such protection. Anti-Fog (A/F) An anti-fog coating is ideal for workers in many extremely hot, cold

or humid conditions. 3M ™DX™ Anti-Fog Hard Coat DX™ is a combination anti-fog, and hard coat that helps provide

abrasion resistance and helps to prevent fogging.

Eye and Face Protection Options Lens Coatings

Eye and Face Protection Options Fitting of Safety Spectacles The closer the eyewear fits to the face, the less chance of an object getting in around the edge of the eyewear and striking the eye. The nosepiece should not slide down the face due to sweat or moisture. Temples should fit comfortably over the ears.

Eye and Face Protection Options Fitting of Safety Spectacles

Many protective eyewear products offer adjustable features and soft materials in points of contact in order to improve fit and comfort to accommodate different face sizes and shapes.

Pantoscopic lens adjustment (3 positions)

Adjustable temple length

Adjustable Nose Piece

Direct vent goggles can help to provide protection against dust and particulates.

They should not be used where a chance of chemical splash can occur.

Eye and Face Protection Options Goggles Direct Vent

Indirect vent goggles can help provide protection against certain airborne particulates and chemical splash.

The vents are designed to allow for adequate ventilation, yet help protect the wearer from liquids entering the eye area.

Eye and Face Protection Options Goggles Indirect Vent

Non–Vented Non Vented goggles can offer better protection against certain

liquids and dusts then vented goggles.

Eye and Face Protection Options Goggles

Extend from the brow to below the chin and across the width of the face and are used to help protect the eye and face against certain impact, chemical, heat and glare hazards.

Eye and Face Protection Options Faceshields

Faceshields are available in many different materials, shapes, sizes, thicknesses and filters (colors).

Use caution when selecting a faceshield, all faceshields are not alike and extreme caution must be exercised in their selection to ensure that the hazardous light is being reduced or eliminated.

Eye and Face Protection Options Faceshield Options

The shape and size of the window needs to be selected to provide adequate coverage of the face while allowing free movement of the head.

A window that is too large may cause restricted head movement while a window that is too small may expose the face, side of head, chin or ears to the hazard.

Eye and Face Protection Options Faceshield Options

Common faceshield materials are polycarbonate, acetate, propionate and PETG. (Polyethylene Terephthalate Glycol) Polycarbonate For use in certain applications with high impact and liquid splash hazards. PETG, Propionate and Acetate For use in certain applications with basic impact and liquid splash hazards.

Mesh For use where increased air circulation is desirable along with face protection (example: forestry and hot environments). Metal mesh faceshields are designed to help protect the wearer from heat sources when there is no risk from molten metal or liquid splash.

Eye and Face Protection Options Faceshields Dark and Medium Green Tint Faceshields with a green tint are used to help to provide

protection from glare.

Reflective coated faceshields are available with an aluminized or gold coating on the outside surface.

Reflective coatings are designed to help protect the wearer from high heat sources by reflecting the heat away from the wearer’s face.

Eye and Face Protection Options Faceshields- Reflective Coatings

Eye and face protection should be inspected prior to each use. Check the frame and lenses to make sure that there are no

cracks or missing parts. Immediately replace the eyewear if any cracks or missing parts

are identified. Immediately replace lenses and faceshields that are scratched or

pitted, or otherwise replace entire device. For shaded or coated lenses, replace lenses or faceshields if the

shade has faded or the coating loses its intended properties.

Eye and Face Protection Options Maintenance

Eye and face protection should be periodically cleaned, especially if visibly soiled. Care must be taken when the lenses or windows have

special coatings, such as anti-fog, as the coatings may be negatively affected with some cleaning agents.

Most eye and face protection can be cleaned with water and mild detergent.

Always follow the manufacturer’s instructions for cleaning.

Lens Cleaning

Total Eyewear Solutions (prescription and non-prescription) Consulting / Specialization

Fitting of both prescription and non-prescription safety eyewear

Supply chain excellence for prescription and non-prescription

Complete Product Line (frames, lenses, accessories)

Science of Fit + Advanced Coatings

Wash and Cleaning Stations

A complete offering to be the Industrial Safety Eyewear Leader

Chris Dujovski Head, Eye & Face Protection 3M Personal Safety Division

Office: 651 736 4608 Mobile: 734 341 4848 cjdujovski@mmm.com

2060 North Kolmar Avenue • Chicago, IL 60639 Call Toll-Free: 800.444.8030 • Fax: 773.384.6677 mail@magidglove.com • www.magidglove.com

Head and Eye Protection Program Essentials

Health & Medicine

Psychophysics of perceiving eye-gaze and head direction

Learning Coordinated Eye and Head Movements: Unifying

A Comparison of Eye-Head Coordination Between Virtual and

From infant hands to parent eyes: Hand-eye coordination ... · Head-mounted eye tracking systems were worn by both participants allowing us to record eye-in-head position from both

Ear hair eye hand head arm leg foot face back nose ear hair eye hand head arm leg foot face back nose mouth

Anatomy of the head – the essentials for surgical practice

Binocular Vision [Eye Essentials] - B. Evans (Elsevier, 2005) WW

A Method to Compensate Head Movements for Mobile Eye

Adaptive Visual Pursuit Involving Eye-Head Coordination and …vislab.isr.ist.utl.pt/wp-content/uploads/2017/11/... · 2017. 11. 24. · Adaptive visual pursuit involving eye-head

Visual Gaze Estimation by Joint Head and Eye Information

Eye Essentials for Every Doctor

Running Head: THE COMPLEX HUMAN EYE 1

Head Massager & Eye Massager

TM ESSENTIALS TIME REWIND - jejordie.com · TIME REWIND Eye Gel with Peptide Complex Key Ingredients Benefits and Suggested Uses Brilliant eye therapy formulated to address all eye

[Www.shamsology.net]Eye Essentials Routine Eye Examination

HEAD-MOUNTED EYE TRACKER - Cornell Engineeringpeople.ece.cornell.edu/land/courses/eceprojectsland/STUDENTPROJ/... · HEAD-MOUNTED EYE TRACKER ... an Eye Tracker is a device that identifies

Feng shui evil eye with ganesha head metal keychain

New Dunlap (1931) Head movements and eye functions of birdswexler.free.fr/library/files/dunlap (1931) head movements... · 2013. 2. 12. · HEAD MOVEMENTS AND EYE FUNCTIONS OP BIRDS

Eye Essentials Routine Eye Examination

Where Is the Driver Looking: Analysis of Head, Eye and ...swiftlet.ucsd.edu/publications/2014/TawariChenTrivedi_ITSC2014.pdf · direction using both head and eye cues. Coarse gaze