View
0
Download
0
Category
Preview:
Citation preview
LubricationManagementSystems
MaterialDispensingManagementSystems
Hose & CableManagementSystems
Diesel & FluidManagementSystems
FireExtinguisher& SuppressionSystems
Onboard Weighing &CCTV Systems
Flow MeasurementSystems
General Lubrication& Exhaust Extraction
www.jsgindustrial.com
• Wireless on board truck scales• Safely measure your loads• Self installation and calibration • Accurate and reliable
Page 2 JSG Industrial Systems
WL sensor 10 bar
Introducing the new Wireless Technology
The new LANX WL onboard truck scale is installed directly into the cab and provides a real-time display of the net, gross, semi-trailer and prime mover axle weights. LANX WL uses a variety of wireless digital sensors positioned on the vehicle’s suspensions and has an alphanumeric screen that displays all weight data. This product is suited with both the owner driver and the fleet manager in mind as the LANX WL is economical and accurate whilst being reliable. It is expandable to include all the trucks in the fleet without any signal interference to other LANX WL displays and electrical equipment.
The LANX WL will save you money as you are able to optimise your loads and improve economic yields in complete safety.
• Wireless communication between the display and sensors.
• Simple and quick installation.
• Correct loads mean safe truck operation.
• You can now load easily within the law limits and avoid fines.
• Reusable system. Sold your truck? Take the LANX WL with you to your new one.
How It Works?
Accuracy: 0 to 1%
WL sensor 10 bar
The wireless digital sensors, which are connected to the prime mover’s rear pneumatic suspension group [1] and on the trailer’s pneumatic suspension group [2], record the pressure variation when product is loaded on to the vehicle. The measured data is sent wirelessly to the LANX WL unit which displays the measured weight in the cab. Since the sensors are self-powered with radio transmitter it requires no cables for power or data transmission.
Advantages
Page 3JSG Industrial Systems
LANX WL S2 or S3 or S4 LANX WL S2 or S3
LANX WL S2 or S3 or S4
A or B A A
A or B A A
A A
Step 2 – Deciding How Many Sensors
Every kit is complete with the LANX WL display panel, 24V socket power adaptor and suitable pneumatic hose and fittings. The kits vary by how many pneumatic sensors are included, that is;
• S2 kit will have two sensors• S3 kit will have three sensors• S4 kit will have four sensors
The amount of sensors you need depends on how many height level valves are found on your vehicle. As a minimum, every level valve on the truck or trailer will require its own sensor. However, for a large axle group that is being serviced by a single level valve such as those on a trailer tri axle, it is typical that a kit with an additional sensor is chosen as it allows for faster measurement. Use the table below to select your kit part number.
Selecting the Right Kit
Step 1 – Suspension Layout
Match your vehicle to the truck suspension layouts below to determine which LANX WL kits are suitable for your application.
Typical Application Level Valves on Truck
Kit Part Number
Bill of Materials
Display Power Supply Sensors Hose Kits
Truck only 2 36-LANX-WL-S2 LANX-WL 12V accessories plug 2 2
Truck and Semi-trailer 2 or 3 36-LANX-WL-S3 LANX-WL 12V accessories plug 3 3
Truck and Lowload trailer 2, 3 or 4 36-LANX-WL-S4 LANX-WL 12V accessories plug 4 4
A = Air Suspension B = Leafspring Suspension
www.jsgindustrial.comSydney | Ph: (02) 9914 8720 | Email: jsgindustrial@jsg.com.au
Melbourne | Ph: (03) 8809 1300 | Email: jsgvic@jsg.com.au
Brisbane | Ph: (07) 3273 3433 | Email: jsgqld@jsg.com.au
Cessnock | Ph: 0447 277 755 | Email: jsghv@jsg.com.au
Mackay | Ph: (07) 4944 0588 | Email: techcq@jsg.com.au
Perth | Ph: (08) 6240 5800 | Email: jsgwa@jsg.com.au
Adelaide | Ph: (08) 8372 9503 | Email: jsgsa@jsg.com.au
Townsville | Ph: 0419 021 892 | Email: jsgfnq@jsg.com.au
Indonesia | Ph: (62-21) 7239 511 | Email: sales@ptjsg.co.id
Technical data specifications & photographs contained in this brochure were correct at time of printing. Pictures shown are for illustration purposes only. Technical information, specifications & products shown maybe subject to change without prior notice. (Errors & omissions excepted). WARNING: For sale & proper use consult instructions, the supplier or JSG. Contact your nearest JSG Industrial Systems P/L distributor for latest information.
Your authorised JSG distributor:
Standard - Display Power Supply Cable with Cigarette Socket
< Optional - Display
Power Supply Cable with Acoustic Alarm
<
Components List Technical Data
LANX WL represents the new generation for on-board weighing on commercial vehicles, born to be a “must-have” for all the truckers who want to know the weight loaded every time and everywhere. Simple and so quick to install thanks to the new wireless digital sensors, it merges the advantage of costs reduction for minor cable maintenance.
Wireless Digital Sensor Self-powered
< Rilsan Hose
with T-fitting
<
Lanx WL Main Unit. Includes mounting bracket (not shown).
<
Lanx WL
Display Back-lit LCD 2 x 16 characters
Screen Tonne or kilogram
Multilingual
Working Temperature 0° to +50° C
Power Supply 18 to 30 Vdc
Protection Level IP40
Max Current 0.5A, 24 Vdc
Dimensions 132 x 100 x 42mm without flange
Colour Matt black
Wireless Sensor 10 bar
Power Supply Primary Li-ion battery (inside)
Connection Wireless
Frequence 2.4 GHz
Range 0-10 bar
Safe Overload 20 bar
Working Temperature -40° to +85° C
Protection Level IP66
Recommended