View
220
Download
0
Category
Tags:
Preview:
Citation preview
ERRORS IN MEASUREMENTS
What is an error?
An error is a mistake of some kind...
…causing an error in your results…
…so the result is not accurate.
ERRORS
Errors can be divided into 2 main classes
Random errors Systematic errors
MISTAKES
Mistakes on the part of an individual such as: misreading scales poor arithmetic and computational skills wrongly transferring raw data to the final
report using the wrong theory and equations
These are a source of error but are not considered as an experimental error
https://myportal.bsd405.org/personal/dossettl/advphys/Shared%20Documents/Types%20of%20Error.pdf
RANDOM ERRORS
Are due to variations in performance of the instrument and the operator
These errors cannot be rectified but can be minimized.
https://myportal.bsd405.org/personal/dossettl/advphys/Shared%20Documents/Types%20of%20Error.pdf
ERRORS RESULT FROM
vibrations and air convection currents in mass readings & temperature variations.
misreadings variations in the thickness of a surface
being measured (thickness of wire) not collecting enough data using a less sensitive instrument when a
more sensitive instrument is available human parallax error
https://myportal.bsd405.org/personal/dossettl/advphys/Shared%20Documents/Types%20of%20Error.pdf
http://www.physics4u.co.uk/
Random errors
These may be due to human error, or a faulty technique.
To reduce the error,take a lot of readings, and then calculate the average (mean).
http://www.physics4u.co.uk/
Random Error- Faulty technique
Example 1
Professor Messer is trying to measure the length of a piece of wood:
Discuss what he is doing wrong.
http://www.physics4u.co.uk/
Random Error- Faulty technique
1. Measuring from 100 end
2. 95.4 is the wrong number
3. ‘mm’ is wrong unit (cm)
4. Hand-held object, wobbling
5. Gap between object & the rule
6. End of object not at the end of the rule
7. Eye is not at the end of the object (parallax)
8. He is on wrong side of the rule to see scale.
Answers:
http://www.physics4u.co.uk/
Human error
Example 2
Reading a scale:
Discuss the best position to put your eye.
youreye
http://www.physics4u.co.uk/
Human error
2 is best.
1 and 3 give the wrong readings.
This is called a parallax error.
youreye
It is due to the gap here, between the pointer and the scale.Should the gap be wide or narrow?
SYSTEMATIC ERRORS
causes random set of measurements to be spread about a value rather than spread about an accepted value
Systematic errors result from: Badly made instruments Poorly calibrated instruments An instrument having a zero error, a form of calibration Poorly timed actions Instrument parallax error Note that systematic errors are not reduced by
multiple readings
https://myportal.bsd405.org/personal/dossettl/advphys/Shared%20Documents/Types%20of%20Error.pdf
http://www.physics4u.co.uk
These errors cause readings to be shifted one way (or the other) from the true reading.
Systematic errors
Your results will be systematically wrong.
Let’s look at some examples . . .
http://www.physics4u.co.uk
Example 1Suppose you are measuring with a ruler:
Systematic errors
If the ruler is wrongly calibrated, or if it expands,then all the readings will be too low (or all too high):
http://www.physics4u.co.uk
Example 2
If you have a parallax error:
Systematic errors
with your eye always too high
then you will get a systematic errorAll your readings will be too high.
http://www.physics4u.co.uk
A particular type of systematic error
is called a zero error.
Systematic errors
Here are some examples . . .
http://www.physics4u.co.uk
Example 3
A spring balance:
Zero errors
Over a period of time, the spring may weaken, and so the pointer does not point to zero:What effect does this have on all the readings?
http://www.physics4u.co.uk
Example 4
Look at this top-pan balance:
Zero errors
There is nothing on it, but it is not reading zero.What effect do you think this will have on all the readings?
It has a zero error.
http://www.physics4u.co.uk
Example 5
Look at this ammeter:
Zero errors
If you used it like this, what effect would it have on your results?
http://www.physics4u.co.uk
Example 6
Look at this voltmeter:
Zero errors
What is the first thing to do?
Use a screwdriver here to adjust the pointer.
http://www.physics4u.co.uk
Example 7
Look at this ammeter:
Zero errors
What can you say?
Is it a zero error?
ACCURACY VERSUS PRECISION
Accuracy is an indication of how close a measurement is to the accepted value
An accurate experiment has a low systematic error
Precision is an indication of the agreement among a number of measurements.
A precise experiment has a low random errorhttp://physicsstudents.edublogs.org/wiki/dp-physics-student-wikis-2014/sung-ei/sung-ei-topic-1/sung-ei-topic-1-2-69/
HIGH PRECISION - HIGH ACCURACY
HIGH PRECISION - LOW ACCURACY
LOW PRECISION - HIGH ACCURACY
LOW PRECISION - LOW ACCURACY
SCATTER GRAPH
http://www.mrcorfe.com/KS4/AQA/Glossary.php#Errors
Used to data display with two sets of variables (dependent and independent).
Points are plotted and a smooth 'Line of Best Fit' is drawn. This shows the general trend and averages out any errors in the data.
The 'Line of best Fit' on a scatter graph is the representation of our best guess at the true values.
The line could be straight ie. linear, or equally correct is a curved line. It is a judgment to be made when looking at the data points. Because of this, there should be at least 5 data points to enable the trend to be correctly identified.
RANDOM ERROR Random errors are represented
on a scatter graph by the distance from the 'Line of Best Fit'.
In the adjacent diagram the green lines show the error.
It is assumed that the error in measuring the independent variable is low compared to that of the dependant variable - hence the green lines are vertical.
If the points are all close to the 'Line of Best Fit' then we can say that our results are good as the error is minimal
http://www.mrcorfe.com/KS4/AQA/Glossary.php#Errors
SYSTEMATIC ERROR
These cause readings to be spread about some value other than the true value
in other words, all the readings are shifted one way or the other way from the true value.
http://www.mrcorfe.com/KS4/AQA/Glossary.php#Errors
ANOMALY
An anomaly is a point significantly out of place compared to the other results.
This is normally due to a misreading or a mistake in the recording / plotting of results.
These should be ignored both when calculating a mean drawing a 'Line of Best Fit' as they are clearly wrong - beyond the realms of random error.
http://www.mrcorfe.com/KS4/AQA/Glossary.php#Errors
RESOURCES
http://www.physics4u.co.uk http://www.mrcorfe.com/KS4/AQA/Gloss
ary.php#Errors
http://physicsstudents.edublogs.org/wiki/dp-physics-student-wikis-2014/sung-ei/sung-ei-topic-1/sung-ei-topic-1-2-69
Recommended