View
0
Download
0
Category
Preview:
Citation preview
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 1
WFCM 2015 Significant Changes and Introduction to High Wind Guides (STD333)
Lori Koch, PEManager, Educational Outreach American Wood Council
This presentation is protected by US and International Copyright laws. Reproduction, distribution, display and use
Copyright Materials
Copyright laws. Reproduction, distribution, display and use of the presentation without written permission of AWC is
prohibited.
© American Wood Council 2016
2
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 2
• The American Wood Council is a Registered Provider with The American Institute of Architects Continuing Education Systems (AIA/CES)
• This course is registered with AIA CES for continuing professional education. As such, it does not include content that may be deemed or construed toEducation Systems (AIA/CES),
Provider # 50111237.
• Credit(s) earned on completion of this course will be reported to AIA CES for AIA members. Certificates of Completion for both AIA members and non-AIA members are available upon
t
that may be deemed or construed to be an approval or endorsement by the AIA of any material of construction or any method or manner ofhandling, using, distributing, or dealing in any material or product.
• Questions related to specific materials, methods, and services will be addressed at the conclusion of this
request.addressed at the conclusion of this presentation.
Description
Engineering concepts from the 2015 Wood Frame Construction Manual (WFCM), used to develop the 2015 WFCM Hi h Wi d G id ill b d l2015 WFCM High Wind Guides, will be covered, along with updates on changes to the 2015 WFCM. The WFCM and High Wind Guides provide designers with time-saving tools using prescriptive solutions (based on structural engineering principles) for wood structures to resist anticipated wind loads. Example problems showing how to apply tabular solutionsproblems showing how to apply tabular solutions offered in the High Wind Guide will also be presented.
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 3
Learning Objectives
1. Be familiar with provisions of the 2015 WFCM and High Wind Guides and relevant references in the 2015 International Residential Code (IRC) and 2015 International Building CodeResidential Code (IRC) and 2015 International Building Code.
2. Be familiar with changes in the 2015 WFCM and how they impact structural design.
3. Understand how roof, floor, and wall assemblies and connections interact as part of a wind uplift and lateral force resisting system.
4 Understand how to appropriately apply tables in both the4. Understand how to appropriately apply tables in both the WFCM and High Wind Guides to determine prescriptive minimums.
Polling Question1. What is your profession?
a) Architect
b) E ib) Engineer
c) Code Official
d) Building Designer
e) Other
6
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 4
Polling Question1b. Did you watch the recommended program
(STD315 – 2012 WFCM Changes) prior to today’s webinar?webinar?
a) Yes
b) No
7
Why design for high wind speeds?Tornado and hurricane resistance!
8
Structure on left can withstand 250m.p.h. winds and a 15 lbs.2” x 4” missile fired at thestructure at 100 m.p.h.!Go to: https://www.fema.gov/wall-sections-passed-previous-missile-impact-tests
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 5
WFCM and IRC/IBC
• 2001 WFCM → 2003, 2006, 2009 IRC/IBC
• 2012 WFCM → 2012 IRC/IBC
2015 WFCM 2015 IRC/IBC• 2015 WFCM → 2015 IRC/IBC
9
WFCM and IRC
• R301.1.1 Alternative Provisions
• WFCM permitted
R301 2 1 1 Wind Design• R301.2.1.1 Wind Design
• For bldgs. where wind design is required or > 110 mph use one or more of the following:
• WFCM
• ICC 600 (newly referenced)
• ASCE 7
• IBC
10
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 6
WFCM and IBC
• Chapter 16 – Determination of Wind Loads Section of IBC (1609.1.1)
• Wind loads in accordance with ASCE 7Wind loads in accordance with ASCE 7
• Exception: residential structures per WFCM
• Not used for structures on hills, ridges, or escarpments
• Chapter 23 – Wood design
• 2301 2 & 2309 conventional• 2301.2 & 2309 conventional construction
11
2015 IBC
12
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 7
2015 IBC
1313
2015 IBC
• Applications
• Single-story
• Slab-on-grade
• L and W < 80’
• Examples
• Restaurants
• Office Buildings
• Design
• Lateral
• Gravity
14
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 8
Polling Question2. The 2015 WFCM can be used to design some
commercial buildings per the 2015 IBC
a) Truea) True
b) False
15
WFCM
• Chapter 1: General
• Chapter 2: Engineered Design
• Chapter 3: Prescriptive Design• Chapter 3: Prescriptive Design
• General outline Chapters 2-3
• Connections
• Floor systems
• Wall systems
• Roof systemsy
• Supplement
16
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 9
WFCM Chapter 1
17
WFCM Chapter 1
• WFCM Table 1 –Applicability Limitations
NEW!
18
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 10
WFCM Chapter 1
• Building dimensions
• mean roof height (MRH) < 33 ft
n mbe of sto ies < 3
ONE
STOR
1 2< 7
M R H
• number of stories < 3
• building length and width < 80 ft
RY
1 2
1 2
M R H
TWO
STORY
T
< 7
< 7
Average grade
M R H
THREE
STORY
19
Chapter 1: General
20
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 11
WFCM Chapter 1
• Items not addressed include ancillary structures such as:
• Decks
• Balconies
• Carports
• Porches
21
• Loads and load path • Continuous• Continuity created by
Chapter 2: Engineered
y yconnections
• Always ends in supporting soil• Building has hundreds of load
paths
22Source: FEMA
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 12
WFCM Chapter 2: Engineered
23
WFCM Chapter 2: Engineered
24
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 13
WFCM Chapter 2: Engineered
Wind uplift Load
25
WFCM Chapter 2: Engineered
26
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 14
WFCM Chapter 3: Prescriptive
27
WFCM Chapter 3: Prescriptive
• WFCM Table 3.1 –Prescriptive Limitations
28
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 15
WFCM Chapter 3: Prescriptive
29
2015 WFCM Changes
• Header Spans Supporting Roof and Ceiling New
30
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 16
2015 WFCM Changes
• Rafters/Ceiling Joists – Brittle Finishes
New
31
2015 WFCM Changes
• New Southern Pine Design Values• Lumber Framing Spans
J i t• Joists
• Rafters
• Studs
• Headers
Revised
32
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 17
2015 WFCM High Wind Guides
Exposure B: 115 – 150 MPH
Exposure C: 115 – 160 MPH
33
2015 WFCM High Wind Guides
• Prescriptive Solutions for:
• Walls
• Floors• Floors
• Roofs
34
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 18
2015 WFCM High Wind Guides (140 MPH)
• Additional limitations beyond WFCM
• Maximum opening height = 6’-8” (can go up to 8’ with exception)
• Require exterior walls to be fully sheathed
• Building Aspect Ratio Limits for 140 MPH: 1.0 ≤ (L/W) ≤ 2.75
• Can go as high as 3:1 at lower speeds
35
2015 WFCM High Wind Guides
36
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 19
Alternative Fasteners
• 2015 WFCM only specifies smooth shank nails
• Sources for info on alternative fasteners
• Manufacturer
• ICC-ES: ESR 1539 Manufacturer’s Equivalency For Nails
• Per engineer’s calculation
37
Polling Question3. The WFCM High Wind Guides have no additional
limitations beyond those imposed in the scope of the WFCMthe WFCM
a) True
b) False
38
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 20
2015 WFCM High Wind Guides• Wall-to-wall connections:
• Or per manufacturer’s specifications for proprietary systems
39
Design ExampleAssumptions
• 140 mph (700-yr, 3-second gust) Exposure B
• L=36’
• W=30’
• 5/12 roof pitch
• Top plate to ridge = 6.25’
• 2-story
• 8’ wall height
• 6’8” door height
• 4’ window height
• Wood Structural Panel Exterior Sheathing w/ Gable End Walls 40
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 21
Design Example
L=36’ W=30’ L/W=1.2
Interpolated Spacing = 47”
41
Design ExampleWall Heights = 8’ OK
42
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 22
Design ExampleTop Plate Splice Nailing Requirements
43
L=36’ – 14 nails
W=30’ – 12 nails
Design Example
44
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 23
Design Example
45
Uplift = 203 lbs (interpolated)
Design Example
46
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 24
Design Example
47
Design ExampleMax. Window Width = 2.5’
48Lateral = 161 lbs (interpolated)
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 25
Design ExampleMax. Window Width = 2.5’ Max. Door = 5’
49
Window Uplift = 330 lbs (interpolated); Lateral = 161 lbs (interpolated)
WFCM High Wind Guide - Prescriptive
Assumes perforated shear wall with hold-downs only at the endsWFCM HWG use ONLY perforated method 50
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 26
WFCM High Wind Guide - Prescriptive
Load Bearing Walls
Second FloorUsing 6” edge/ 12” field spacing:L/W = 36'/30' = 1.2Interpolated = 36.2% = 13'Available = 23.5' OKHold Down Capacity = 4,360 lb
51
WFCM High Wind Guide - Prescriptive
Load Bearing Walls
First FloorFirst FloorUsing 6” edge/ 12” field spacing:L/W = 36'/30' = 1.2Interpolated = 59.8% = 21.5'Available = 21' NG!
Using 4” edge/ 12” field spacing:L/W = 36'/30' = 1.2Interpolated = 46.8% = 16.9'Available = 21' OKHold Down Capacity = 5,900 lb
Combined Hold-down5,900 + 4,360 = 10,260 lb
52
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 27
WFCM High Wind Guide - Prescriptive
Gable End – Second FloorUsing 6” edge/ 12” field spacing:L/W = 36'/30' = 1.2Interpolated = 47.4% = 14.2’Openings = 15.8’Hold Down Capacity = 4,360 lb
Gable End – First FloorUsing 6” edge/ 12” field spacing:L/W = 36'/30' = 1.2Interpolated = 75% = 22.5’Openings = 7 5’Openings = 7.5Hold Down Capacity = 4,360 lb
Combined Hold-down4,360 + 4,360 = 8,720 lb
53
WFCM High Wind Guide - Prescriptive
Controlling Hold‐Down – 1st floor10,260 lb > 8,720 lb
10 260 lb can be used at all 4 corners on 1st floor10,260 lb can be used at all 4 corners on 1st floor
542nd floor hold downs require 4,360 lb capacity
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 28
WFCM High Wind Guide - Prescriptive
Uplift = 300 lbs (interpolated)
55
WFCM High Wind Guide - Prescriptive
Ridge Strap = 274 plf (interpolated)
56
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 29
Prescriptive Solutions• WFCM and High Wind Guides specify
capacity requirements for engineered connectors, straps, and hold downs
M f t id it f• Manufacturer provides capacity of individual components
57
Polling Question4. The 2015 WFCM HWG uses the ____________
method for shearwall design.
a) Segmenteda) Segmented
b) Perforated
c) Force Transfer Around Openings (FTAO)
d) All of the above
58
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 30
WFCM Changes
• White paper
http://www.awc.org/pdf/2015 WFCM-Changes-Web.pdf
59What’s Changed?
Technical Articles
• Structure Magazine• 2015 NDS
• January 2015
• 2015 WFCM• February 2015
• 2015 SDPWS• July 2015
60What’s Changed?
American Wood Councilwww.awc.org
Copyright © American Wood Council. All rights reserved. 31
Polling Question5. The WFCM HWG specifies ___________ for
connections such as ridge straps, uplift straps, and hold downs.hold downs.
a) Minimum capacity requirements
b) Quantities
c) Manufacturer name brands
d) Model numbers
61
• This concludes The American Institute of Architects Continuing Education Systems Course
Questions?
info@awc.orgwww.awc.org
62
Recommended