View
248
Download
0
Category
Preview:
Citation preview
Introduction
Purpose of the Guide
1. This Guide is intended primarily for the use of Examiners within VOSA and Authorised Constables. However, it is made available more widely so that vehicle owners, operators and drivers can become more aware of VOSA’s standards.
Its purpose is:
• to provide guidance on the action to take when roadworthiness defects are found during vehicle inspections;
• to promote consistency among Examiners
2. The Guide is not a legal document and must not be treated as an interpretation of the relevant legislation, which only the courts can provide.
Layout of the Guide
3. This publication is divided into three parts covering the main groups of road vehicles.
Part 1 is intended for heavy goods andpublic service vehicles and may also beused for agricultural motor vehicles,trailers and trailed appliances (see notebelow).
Part 2 is for cars, private buses and lightgoods vehicles.
Part 3 is for motorcycles includingcombinations.
Note: An agricultural motor vehicle,trailer or trailed appliance is one that is constructed or adapted for use off roadsfor the purpose of agriculture, horticultureor forestry and which is primarily used forone or more of those purposes, but doesnot include a "dual-purpose" vehicle asdefined in the Road Vehicles (Construction and Use) Regulations.
They fall into two distinct groups: thosedriven/drawn at speeds not exceeding20mph and those driven/drawn at speedsin excess of 20mph.
When using Part 1 of this document inconnection with the inspection of anagricultural motor vehicle, trailer or trailedappliance the following exceptions mustbe noted:
For all types of agricultural vehicle IM references 3, 21, 24 and 33 will not apply.
For types driven/drawn at speeds not in excess of 20mph the following IMs might not apply, or might apply in part only: IMs 5, 7, 8, 12, 14, 17, 22, 23, 24, 25, 26, 27, 48, 62 to 67 inclusive and 71 to 73 inclusive.
As a general rule when inspecting these slower vehicles and using the IMs mentioned above, Examiners should only be concerned with items that they find fitted. That is, a vehicle should not be considered defective if a particular item was not fitted as original equipment.
4. The page layout for all three parts is the same and consists of four columns.
Column 1: describes the defect;
Column 2: describes the severity of the defect;
Column 3: gives guidance on the action to be taken;
Column 4: gives guidance notes on standards and legal requirements.
Categorisation of Defects April 08 i
Introduction
Policy on the Issue of Prohibitions
5. A Prohibition Notice (PG9) is a ban on the use of a vehicle on a public road. A prohibition will normally be issued where a vehicle is found by an Examiner to be, or likely to become, unfit for use or where driving of the vehicle would involve a risk of injury to any person.
6. When a prohibition is in force it is an offence to drive or tow or permit to be used, a vehicle on the road unless an exemption notice has been issued or when certain circumstances as listed on the reverse of the prohibition notice apply.
7. In addition to preventing the further use of seriously defective vehicles on the road, prohibition notices are used:
• to notify the operator or owner of the defect(s) that caused the prohibition, so that they can be put right before the removal of the prohibition;
• in the case of vehicles subject to operator licensing, to inform the Traffic Commissioner that prohibitable defects have been found;
• to enable VOSA to target additional enforcement checks on operators whose record suggests that maintenance is inadequate.
Note 1: VOSA is required by law to send a copy of each prohibition to the relevant Traffic Commissioner.
Note 2: A Commissioner can curtail, revoke or suspend licences on the basis of prohibitions, convictions or failure to comply with the conditions of holding a licence, one of which is the requirement to have arrangements for ensuring adequate maintenance.
8. A prohibition might take effect immediately or could be delayed for up to ten days. Immediate prohibitions are issued where, in the opinion of an Examiner, the defects on the vehicle are such that further driving of it would involve a risk of injury to any person.
Where, in the Examiner’s opinion, no such risk exists, the prohibition will come into force at such time, not later than 10 days from the date of the inspection (delayed prohibition) as seems appropriate to the Examiner, having regard to all the circumstances, and will afterwards continue in force until it is removed.
A delayed prohibition allows continued use of the vehicle until the prohibition comes into force. The period of delay on prohibitions will reflect
• the severity and number of defects observed,
• their significance in road safety and environmental terms,
• any risk presented by continued use of the vehicle,
while taking into account the operational and financial implications for the operator.
April 08 VOSA ii
Introduction
Period of Delay
Examiners will normally select one of the following periods of delay, which have been grouped together into three bands according to the number and severity of the defects listed on the prohibition notice (PG9):
Band Period of Delay Severity of Defects Listed on the PG9
A Maximum 10 days Less than 5 defects in non critical areas;
B 4 to 7 days 1 defect in a safety critical area or 5 or more defects in non critical areas;
C Up to 3 days More than 1 defect in a safety critical area of the vehicle.
Definition of Safety Critical Safety Critical defects or systems are those that could affect the control or directional stability of the vehicle.
Throughout this Guide, recommendations are indicated by a letter in the action column, as follows
"I" denotes an immediate prohibition
"D" denotes a delayed prohibition
"IN" advisory defects not considered serious enough to prohibit the vehicle. They are reported on a Vehicle Inspection Notice explained in the following paragraph.
9. Where Examiners find on a vehicle roadworthiness defects not serious enough to warrant prohibition, they will advise the user/ owner using a Vehicle Inspection Notice. This notice is advisory only and does not in itself prevent further use of the vehicle.
Even if not prohibitable, some of the defects may mean that the vehicle is unroadworthy and does not comply with the law. Continued use of a vehicle issued with either a Delayed Prohibition or a Vehicle Inspection Notice listing advisory defect(s) risks prosecution under the Road Vehicles (Construction and Use) Regulations or Road Vehicles Lighting Regulations and so it will be in the user’s interest to repair defects as soon as practicable after they are noticed.
Note: A Technical Roadside Inspection Report (PG35EC) will be issued following a HGV/ PSV spot check examination in place of a Vehicle Inspection Notice used for other vehicles. This will include any advisory defects.
Categorisation of Defects April 08 iii
Introduction
Vehicles Undergoing Repair
10. As a general rule, vehicles undergoing repair, and those partially dismantled and awaiting spare parts should not be examined. However, where it is reasonable to assume the extent of the repair is limited or is of a token nature only and the vehicle’s general appearance suggests that it was last used on the road in a seriously defective condition, an examination may be carried out of the items not receiving attention. A prohibition, if issued, should be endorsed "UNDER REPAIR".
Vehicles Awaiting Repair or Scrapping
11. Vehicles parked on operators’ premises and claimed to have been withdrawn from use pending repair or scrapping can be examined if it appears that the vehicle has recently been used on the road in a seriously defective state.
As with vehicles undergoing repair, the fact that the vehicle was off the road and claimed to be withdrawn from service should be noted on a prohibition, if issued, by endorsing it "AWAITING DISPOSAL" or "AWAITING REPAIR".
Vehicles Claimed to be Out of Use
12. Vehicles claimed to be withdrawn from use should be treated as in the previous two paragraphs in that they should generally not be examined or prohibited. Where there is doubt about an operator’s claim, Examiners should seek firm evidence of non-use, for example evidence of de-licensing. However, such evidence does not preclude an examination if it appears that the vehicle has been recently used, or it is likely to be used on the road in a seriously defective condition. In these circumstances a prohibition, if issued, should be endorsed with a comment to indicate that the vehicle was claimed to have been withdrawn from service.
Vehicles Damaged in Collisions
13. Vehicles examined following collisions should generally not be prohibited if all defects arose from the collision unless it is believed that further use of the vehicle in a defective state is intended. If there are prohibitable defects which preexisted the collision a prohibition will be issued and the collision damage included on the notice. It must be made clear which items were caused by the collision and which were present before. To achieve this, segregate the defects with the headings, "COLLISION DAMAGE" and "DEFECTS NOT DUE TO COLLISION ".
April 08 VOSA iv
Introduction
Standards for Prohibition Issue
14. This Guide also explains the standards that guide Examiners on the issue of prohibition notices to unroadworthy vehicles following inspections at any location.
When making decisions on roadworthiness, Examiners will take into account such factors as prevailing weather, vehicle use and configuration, and other information issued by VOSA, such as statutory test inspection manuals, amplification notes and technical bulletins.
15. When dealing with vehicles that have been Type Approved, approved to a national scheme or certified to the Cetificate of Initial Fitness requirements (PSVs only), Examiners need to be careful not to require higher standards of construction, or the fitment of items, than were required/ fitted when the vehicle was manufactured and ‘approved’.
16. Examiners will record decisions on the appropriate prohibition document concisely and clearly. Descriptions such as "worn", "loose", "noisy", "broken", "fractured", "inefficient", corroded", are not sufficient on their own. Where possible, sufficient detail should be recorded about defective components to enable subsequent identification. Tyre sizes and serial numbers should be recorded for each defective tyre listed on the prohibition.
Examples
Inadequate Wording
a. Free play front wheel bearing
b. Handbrake mechanism seized
c. Front brake pipe chafed
d. Leakage of brake fluid O/S rear
e. Exhaust smoking
Suggested Wording
Excessive free play nearside front wheel bearing.
Handbrake mechanism seized and handbrake ineffective.
Offside front brake flexible hose chafed almost through.
Severe leakage of brake fluid from O/S rear brake cylinder when brake applied.
Exhaust emitting excessive black smoke.
Categorisation of Defects April 08 v
Introduction
17. The term "insecure" is used many times throughout this Guide to describe a defective condition. This term should be taken by Examiners to mean either:
• that a component on the vehicle has relative movement (looseness) at its fixings or in relation to an associated component where there should be none, or
• that a component is not safely or completely attached at its fixing or to an associated component.
All components on a vehicle must be safely attached while it is in use on the road. However, how safely a component needs to be attached depends on its function.
Areas of the vehicle considered critical in terms of the likelihood of the vehicle to endanger the driver, any passengers and other users of the road, can tolerate fewer fixings that are broken, loose, missing or otherwise ineffective than those in a less critical part of the vehicle.
The proportion will depend on factors such as the design of the component etc, but as a general rule, no more than 20% (1 in 5) of the fixing devices should be loose etc. More than this proportion means that the remaining fixing devices could be overstressed and could therefore fail at any time. Examples of critical systems include (this is not an exhaustive list):
• steering except those components not subject to
• brakes heavy loads or forces, eg} power steering reservoirs or brake relay valves
• suspension linkages • trailer couplings • live (ie moving) transmission
components • wheels and hubs
The proportion suggested above does not apply to:
• components in a critical area or system secured by a single fixing device. If this device is loose, broken etc, the component is to be considered insecure.
• components in a critical area or system where detailed instructions are given in the manual (eg wheel studs/nuts). In such cases, these instructions must be used in preference.
Components that are not part of a critical system, eg some body panels, can tolerate a higher proportion of their fixings either loose, broken etc. Again, the proportion will depend on the design of the component but, as a general rule, no more than 33% (1 in 3) of the fixing devices should be loose, broken, missing or otherwise ineffective.
A component secured by a non standard, temporary means should be judged on its merits.
18. The nature of each defect listed on the prohibition must be such that, had it been the sole defect detected, prohibition action would still be justified. The number of defects found is not a criterion for the issue of a prohibition.
19. Notwithstanding the guidance above, prohibition notices are allowed to be issued for any failure to comply with the Road Vehicles (Construction and Use) Regulations or the Road Vehicles Lighting Regulations, where the Examiner is satisfied that the vehicle is, or is likely to become, unfit for service.
April 08 VOSA vi
Introduction
20. The scope of any inspection of the vehicle might be limited by the circumstances at the inspection site, by the vehicle’s design or construction and by the absence of particular inspection facilities.
For this reason, there might be other defects that cannot be seen at the time of the inspection and are therefore not listed on the prohibition or vehicle inspection notice. In some cases, checks will be made on specific areas of the vehicle only, eg exhaust emissions.
Variation Notices (PG9A)
21. Variation Notices are used to alter certain details of an existing prohibition. This will normally be necessary following a subsequent inspection of the vehicle that reveals additional defects or where some but not all of the defects listed on the prohibition have been rectified.
In addition to altering the list of defects, Variation Notices can alter the time and date of an existing prohibition by making a delayed prohibition ‘Immediate’ or vice versa.
Exemptions (PG9B)
22. Exemption Notices are issued to permit prohibited vehicles to proceed to a place of repair under controlled conditions once the prohibition has come into force. The conditions of movement will be detailed on the Exemption Notice. Examiners will normally issue an Exemption Notice only if in their opinion the vehicle can be moved to such a place without risk to public safety.
Removal of Prohibitions
23. Before a prohibited vehicle can be used again on a public road the Prohibition Notice must be removed by the issue of a ‘Removal of Prohibition’ Notice (PG10). An Examiner is allowed to remove a roadworthiness prohibition when satisfied that the vehicle is "fit for service".
Accordingly, where a further more extensive inspection is required and the available inspection facilities are inadequate for that purpose, an Examiner may direct the vehicle to a testing station for an inspection prior to removing the prohibition.
24. Examiners are advised that "fit for service" must be taken as meaning that, if tested, the vehicle would comply with all the relevant annual test standards. The discovery of defects that would result in an annual test failure could be given as a reason for refusing to remove a prohibition.
25. Vehicles subject to the MOT test will normally be considered "fit for service" when they have passed the test and have been issued with a pass certificate (VT20/VT20W) dated after the date of the prohibition notice issue.
26. In the case of heavy goods vehicles and public service vehicles, the law imposes the responsibility on the Examiner considering removing a roadworthiness prohibition, of satisfying himself that the vehicle is "fit for service".
In law, Examiners have absolute discretion over the scope of examination, which in their opinion is necessary for them to be satisfied that the vehicle is "fit for service".
Categorisation of Defects April 08 vii
Introduction
27. VOSA provides general guidance only on how Examiners will satisfy themselves that a vehicle is "fit for service".
The Examiner to whom a vehicle is presented for prohibition clearance will need to take into account any recommendation regarding the level of clearance inspection recorded on the Prohibition Notice by the issuing Examiner.
He/ she will bear in mind that the issuing Examiner should have already taken into account the following factors in framing their recommendation:
• whether he/ she would have cleared the prohibition "on site", without a further more extensive examination, had the defects been rectified then;
• the extent of the inspection already conducted;
• the nature of the defects described on the PG9.
In addition to these the clearing Examiner will need to take the following factors into account:
• any comments made by the Examiner or Authorised Constable;
• the time elapsed and mileage covered since the issue of the prohibition;
• the operator’s maintenance history;
• the date of the last annual inspection.
28. More detailed information on the procedures to be followed in order to have roadworthiness prohibitions removed is provided on the reverse side of the Prohibition Notice.
April 08 VOSA viii
Introduction
Complaints and Appeals
29. The Law does not provide for a statutory appeal against the issue of a prohibition. However, VOSA does have a formal complaints procedure. Police issued prohibitions are outside the scope of this procedure.
Operators wishing to use this procedure will find information on the reverse of the Prohibition Notice handed to the driver by the issuing Examiner at the time the prohibition is issued.
If owners, operators or drivers feel they have been unfairly or harshly treated, they can complain to the relevant manager at the local VOSA Office.
On these occasions, operators can use this Guide to judge whether the action taken was consistent with VOSA’s published guidance. Each complaint will be logged, acknowledged and a formal written reply provided.
Complaints can be dealt with most easily at the local VOSA Office level since the vehicle and prohibition notice will normally be readily available.
However, where an operator is dissatisfied with the outcome of their complaint and wishes to escalate their points they should be forwarded to the Customer Complaints Co-ordinator.
Letters should be addressed to:
Customer Complaints Co-ordinator Vehicle and Operator Services Agency, Berkeley House, Croydon Street, Bristol BS5 0DA
30. If you continue to be dissatisfied with the treatment of your complaint, you may write to the Chief Executive who may refer your grievance to the independent adjudicator.
31. Regulations provide for appeals to be made against the refusal of an Examiner (or Authorised Constable) to remove a Prohibition Notice.
The owner or operator of the vehicle may appeal (in writing) within 14 days to the address above.
Categorisation of Defects April 08 ix
VOSA Categorisation of Defects Contents Part 1: Public Service, Heavy Goods and Agricultural Vehicles
IM No.* Page #3 Seat Belts………………………….............1
#5 Exhaust Emissions...................…............4
6 Road Wheels and Hubs...........................5
#7 Size and Type of Tyres.............................7
#8 Condition of Tyres....................................8
9 Sideguards, Rear Under-Run Devices and Bumper Bars...11
10 Spare Wheel and Carrier........................16
11 Vehicle to Trailer Coupling.....................17
#12 Trailer Parking and Emergency Brakes and Air Line Connections...........20
13 Trailer Landing Legs..............................22
#14 Spray Suppression, Wings and Wheel Arches....................................................23
15 Cab Security.......................................... 26
16 Driver and Passenger Doors .................27
#17 Driver’s Accommodation and Steps........32
18 Driver’s Seat...........................................33
19 Security of Body.....................................34
20 Condition of Body...................................37
#21 Interior of Body.......................................40
IM No.* Page #22 Driver’s Mirrors.......................................50
#23 Glass and View of the Road....................51
#24 Accessibility Features.............................54
#25 Windscreen Wipers and Washers..........62
#26 Speedometer / Tachograph.................. .63
#27 Audible Warning (Horn)..........................64
28 Driving Controls......................................65
30 Steering Control......................................66
#33 Speed Limiters........................................68
34 Pressure /Vacuum Warning and Build Up...........................................71
36 Hand Lever Operating Mechanical Brakes....73
37 Service Brake Pedal...............................74
38 Service Brake Operation.........................75
39 Hand Operated Brake Control Valve......78
41 Condition of Chassis.............................. 79
42 Electrical Wiring and Equipment.............80
43 Engine and Transmission ......................81
44 Oil and Waste Leaks..............................82
45 Fuel Tanks and Systems........................83
46 Exhaust Systems and PSV Waste Systems.................................................84
IM No.* Page #48 Suspension.............................................85
53 Axles, Stub Axles and Wheel Bearings......................................90 1
54 Steering Mechanism...............................91
57 Transmission...........................................95
58 Additional Braking Devices (including retarders)................................................96
59 Brake Systems and Components...........97
#62 Rear Markings and Reflectors...............104
#63 Lamps...................................................105
#66 Direction Indicators and Hazard Warning Lamps...................................................109
#67 Aim of Headlamps.................................110
#71 Service Brake Performance..................111
#72 Secondary Brake Performance.............113
#73 Parking Brake Performance..................115
*IM = Inspection Manual for HGV and PSVs # = For agricultural vehicles see paragraph 3 of the Introduction
Part 1: Public Service, Heavy Goods IM3 and Agricultural Vehicles Seat Belts
1
Description of Defect Severity of Defect Action Notes
Seat Belts (See Notes) NOTE: THIS IM ITEM DOES NOT APPLY TO AGRICULTURAL VEHICLES
Any dangerous defect/ damage/ feature Likely to inflict injury I of a seat belt restraint system 1. The legal requirements for fitment of
seat belts are too complex to be Any obligatory seat belt missing (See - D repeated in this guide. Refer to the Notes 2, 3 and 5) relevant Inspection Manual.
As general guidance, Notes 2 and 3 Any obligatory or non obligatory seat Not capable of performing its intended D below have been included. belt vandalised/inoperative/ defective/ purpose or likely to fail when required 2. Goods vehicles first used on or after 1 insecure/ anchorage or seat mounting (See Note 2) October 2001 and that exceed 3500kg weak (See Notes 5, 6 and 7) design gross weight are required to be
fitted with seat belts to the drivers’ and front passenger seats.
3. Seat belts are required to be fitted to • driver’s and specified front passenger
seat on minibuses - first used before 1 October 1988 - with not more than 12 passenger seats
• all front seats on minibuses first used on or after 1 October 1988 - with up to and including 16
passenger seats - not exceeding 3500kg design
gross weight • forward facing exposed seats on
coaches first used on or after 1 October 1988
• all seats in buses, coaches and minibuses first used from 1 October 2001 which are not authorised to carry standing passengers.
Categorisation of Defects April 08 1
IM3 Part 1: Public Service, Heavy GoodsSeat Belts and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Seat Belts (cont’d) 4. In this item the term "seat belt" includes the belt, its mountings and seat to which it is fitted.
5. "Obligatory belt/ s" in this item means those belts which are required to be fitted by virtue of the vehicle’s construction. The term "nonobligatory belt/ s" means any additional belts fitted and includes those required by virtue of the vehicle’s use.
6. As a guide, defective includes excessive corrosion, serious deterioration or fracture in load bearing area within 300mm of anchorage.
7. When taking prohibition action in respect of vandalism, if examiners are able to establish that the damage is recent and no reflection on the operator’s maintenance system they should endorse the defect ‘Not maintenance related’.
April 08 VOSA 2
Part 1: Public Service, Heavy Goods IM3 and Agricultural Vehicles Seat Belts
1
Description of Defect Severity of Defect Action Notes
Seat Belts (cont’d) 8. Prohibition action will not be appropriate where there are insufficient belts on forward facing seats for the number of children being carried on an organised trip. Prosecution action will be taken in this situation.
9. Large buses, except coaches, are not required to be fitted with belts either by virtue of their construction or use. Coaches can be converted into buses by limiting their powered speed to less than 97km/h (60mph). However, the conversion must not be readily reversible i.e. the limiter system must be sealed to prevent tampering.
10. A seat belt is a minimum of a lap belt.
Categorisation of Defects April 08 3
IM 5 Part 1: Public Service, Heavy GoodsExhaust Emissions and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Diesel Smoke Emission
Exhaust emitting excessive smoke (See Notes 1, 2, 3 and 4)
Spark Ignition Engine Emissions
Exhaust emitting excessive levels of pollutants (See Notes 2 and 3)
Sufficient to obscure vision or likely to cause danger to other road users
Smoke levels exceed annual test standard by more than 10% or; black haze or darker, or other colour which tends to obscure vision
Exceeding the annual test limits by 10% or less or continuous haze, any colour
Sufficient to obscure vision or likely to cause danger to other road users
Emission levels exceed the annual test standard by more than 10%, or tends to obscure vision
Exceeding the annual test limits by 10% or less or continuous haze, any colour
I
D
IN
I
D
IN
1. Turbocharged engines might emit smoke on free acceleration. This is not necessarily a defect.
2. This inspection also applies to vehicle auxiliary engines that are in operation when the vehicle is seen.
3. The annual test standard applies only to vehicles subject to statutory annual test and, for the purposes of prohibition issue, a margin equivalent to 10% of the limits will be allowed to exclude marginal infringements.
4. The Light Absorption Coefficient Scale used for diesel exhaust smoke, being logarithmic, results in standards for delayed prohibition issue of >3.7m-1 for turbocharged engines, and >3.0m-1 for naturally aspirated engines when the 10% margin is added to the prescribed limits.
April 08 VOSA 4
Part 1: Public Service, Heavy Goods IM 6 and Agricultural Vehicles Road Wheels and Hubs
1
Description of Defect Severity of Defect Action Notes
Road Wheels and Hubs
Any wheel(s) missing
Wheel fractured or welding breaking away
Wheel hub fractured
Wheel stud holes elongated/ damaged
Wheel nut, washer or stud missing/ loose/ fractured, not clamping or fully locating in taper
-
Failure imminent (see Note 1)
Otherwise than above
Failure or detachment imminent
Otherwise than above
If visible with wheel nuts in place or detachment likely
Any stud hole severely worn/ elongated
More than one wheel nut/ stud is missing, loose or obviously not clamping or locating in the road wheel taper (see Note 4)
More than one spigot wheel nut washer fractured
I
I
D
I
D
I
D
I
I
1. Fracture at the bridge over the valve is not considered a reason for action.
2. In the case of wheels with detachable spring retaining rings fitted to wheel rims of the semi-drop centre type (these are identified by the ends of the ring, which are shaped so as to interlock), abutting ends are permissible provided the retainer is adequately and safely located in the wheel rim.
3. A tyre retaining ring butting causing the flange to lift more than 1.5mm is to be regarded as excessively displaced.
4. Some agricultural vehicles have extra fixings for the sole purpose of attaching additional wheels. These are not part of this inspection while additional wheels are not fitted.
Any one stud or nut missing or loose (See Note 4)
D
Any one spigot wheel nut washer fractured D
Excessive clearance between hub spigot and wheel
A diametric aggregated clearance of more than 3mm between the spigot and the locating surface of the wheel
D
Otherwise than above IN
Categorisation of Defects April 08 5
IM 6 Part 1: Public Service, Heavy GoodsRoad Wheels and Hubs and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Road Wheels and Hubs
Tyre retaining ring abutting or fractured
Wheel seriously distorted
Half shaft bolts, nuts or studs loose/ missing
Incompatible wheel fitted
Retaining ring is excessively displaced from its seating and total displacement is imminent (See Notes 2 and 3)
Affecting steering or vehicle stability
Otherwise than above
Loss of drive or detachment likely
Otherwise than above
Fouling other components where failure of the wheel or affected component is likely
Otherwise than above
I
I
IN
I
IN
I
IN
April 08 VOSA 6
Part 1: Public Service, Heavy Goods IM7 and Agricultural Vehicles Size and Type of Tyres
Description of Defect Severity of Defect Action Notes
Tyres
The nominal size, ply rating, load index, speed rating of any is below that appropriate for the vehicle
Tyres of different types/ nominal sizes/ aspect ratio fitted on an axle
A tyre’s application does not comply with its ‘condition of use’ marking
Radial ply tyres fitted to front axle and crossply or bias-belted to rear axle or bias-belted to front axle and crossply to rear axle
Tyres of different types fitted on steerable axles
Tyres of different types fitted on driven, non steerable axles
If tyre is obviously overloaded
Otherwise than above (see Notes 1 and 2)
Tyre of different type (ie cross ply or radial) fitted
One tyre is of a different nominal size or aspect ratio from those on the same axle (See Note 2)
(See Note 6)
(See Note 3)
(See Note 4)
(See Note 5)
I
D
I
D
IN
I
I
I
NOTE: PNEUMATIC TYRES ARE NOT A LEGAL REQUIREMENT ON AGRICULTURAL VEHICLES NOT DRIVEN/ DRAWN AT MORE THAN 20MPH
1. It is appreciated that during roadside inspection Examiners might not have access to tyre tables, and in some instances the size or ply rating might not be readily identifiable.
2. It cannot be assumed that, because either tyre of a twin wheel is not in contact with the ground when the vehicle is stationary on a level surface, there is a difference in nominal size.
3. This does not apply to vehicles with twin or extra wide tyres on the rear axle, or to tyres manufactured for (and fitted to) engineering plant. It also does not apply to vehicles with a maximum speed not exceeding 30mph.
4. Applies only for 2 or more steerableaxles.
5. Applies only for 2 or more driven nonsteerable axles.
6. e.g. ‘Trailer Use Only’, ‘FRT’,`Directional Tyres.
Categorisation of Defects April 08 7
1
IM8 Part 1: Public Service, Heavy GoodsCondition of Tyres and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
Tyres NOTE: THIS IM ITEM DOES NOT APPLY TO AGRICULTURAL VEHICLES NOT
Tyre walls in contact Caused by under inflation or incorrect wheel fitting (See Note 1)
IN DRIVEN/ DRAWN AT MORE THAN 20MPH
1. Some tyres, e.g. radials, with flexible side walls might "kiss" under load. In
Tyre bulging or tread lifting
Tyre has a break in the fabric or deep cut (See Note 2a) or damage to the side wall or tread area
Caused by separation or partial failure of its structure (See Note 2)
Body cords damaged (See Note 3)
Cut 25mm or longer exposing body cords
I
I
D
these cases, wall contact is not a reason for rejection.
2. Bulging includes any lifting of the tread rubber and must not be confused with undulations which might be present due to
Body cords exposed (See Note 2b)
Breaker cords damaged in the tread area
Breaker cords exposed in the tread area
D
D
IN
manufacturing imperfections. In the case of capped re-treads care must be taken not to confuse unbonded tread overlapping the tyre wall with tread separation. A bulge in the sidewall area may be up to 5mm
Tyre seriously under inflated
Otherwise than above (See Note 2a)
Likely to affect steering or overload the other tyre on a twin fitment
IN
I
proud of the original sidewall. In most cases, the tyre will be stamped with ‘BSAU 159e’ or ‘BSAU 159f’ in the vicinity of the repair. A repair will feel solid and should not deflect as would a bulge associated with casing
In the case of a single tyre fitment on a non-steered axle
Otherwise than above
I
IN
separation. 2a. Cuts which are deep enough to
reach the body cords or ply but are less than 25mm or 10% of the section width, whichever is the greater, and have not damaged or exposed the body cords or ply do not breach the legal requirements for tyres.
2b. “Exposed” for this purpose means the cords are visible or it can be established that they are exposed with the use of a probe.
April 08 VOSA 8
Part 1: Public Service, Heavy Goods IM8 and Agricultural Vehicles Condition of Tyres
1
The breaker cords are layers of steel cord cut at various angles and placed on top of each other over the ply and under the tread. The purpose of the breaker cords is to keep the tread flat on the road surface, they have no effect on the strength of the tyre.
TYPICAL CONSTRUCTION OF A RADIAL TYRE
BODY CORDS
BREAKER CORDS
Categorisation of Defects April 08
Part 1: Public Service, Heavy Goods IM8 and Agricultural Vehicles Condition of Tyres
1
Description of Defect Severity of Defect Action Notes
Tyre tread worn beyond legal limit Depth of tread is not at least 1mm I 3. Body cords are those extending from throughout a continuous (excluding tie-bars) bead to bead. circumferential band for at least three quarters of the tread width on Although damage to such cords has a
different effect on tyres of radial and • any tyre on a steered axle, or • 50% or more of the total number of
tyres fitted to non-steered axles.
crossply construction, the problems of differentiation are very complex and the stated standards must be applied.
(See Note 4) Body cords must not be confused
Otherwise than above D with the breaker cords in the tread area. The consequence of damage
The base of any groove of the original tread IN to breaker cords is not generally so pattern is not clearly visible (See Note 5) severe. For this reason, the different
action is recommended. Tyre fouling Tyre damaged and/ or likely to fail I
4. Tie-bars are short projections formed Otherwise than above IN into the base of the tread pattern
grooves to brace or stiffen the Recut tyre fitted Fitted to vehicle on which recut tyres are IN adjacent ribs or blocks in the initial full
not permitted (See Note 6) depth state of the tread pattern.
Spare Tyre In the initial full depth stage, the tie-bar upper surface will be below the
Spare tyre bulging/ fabric cut/ fabric - IN tread surface. exposed/ tread worn beyond legal limit
In the later stages of tread wear the tie-bars might interrupt the continuity of the tread pattern grooves. This is acceptable.
Steered axle is one used to control the direction of the vehicle by the driver.
Categorisation of Defects April 08 9
1
IM 8 Part 1: Public Service, Heavy GoodsCondition of Tyres and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
5. "Original Tread Pattern" means:
a. In the case of a re-treaded tyre, thetread pattern immediately after thetyre was re-treaded.
b. In the case of a wholly re-cut tyre,the manufacturer’s re-cut tread pattern.
c. In the case of a partially re-cut tyre,on the part that has been re-cut, themanufacturer’s re-cut tread pattern,and on the other part, the treadpattern of the tyre when new.
d. In the case of any other tyre, thetread pattern of the tyre when the tyre was new.
Note: Grooves which wear out before the main grooves and other minor featuressuch as sipes, small lateral extensions tothe circumferential grooves and minorlateral grooving on the shoulders areto be disregarded when consideringwhether the “original tread pattern” is visible.
6. It is permissible for re-cut tyres to befitted to:
• motor vehicles of unladen weightexceeding 3050kg, or between2540kg and 3050kg if fitted to wheelrims exceeding 405mm diameter,and
• trailers of unladen weight exceeding1020kg (2290kg total weight forfixed plant carriers).
April 08 VOSA 10
Part 1: Public Service, Heavy Goods IM 9 Sideguards, Rear Under-run and Agricultural Vehicles Devices & Bumper Bars
1
Description of Defect Severity of Defect Action Notes
Bumpers, Sideguards and Under-run Devices (See Note 1)
Bumper bar, sideguard or under-run device insecure, damaged or missing
Detachment likely either partially or completely or having projections or jagged edges likely to cause injury
Missing where required
Otherwise than above
I
D
IN
Note 1 - Application and Exemptions
Sideguards - Application Motor Vehicles first used from 1 April 1984 with a design gross weight exceeding 3,500kg and where the distance between the centres of any two consecutive axles exceeds 3m.
Trailers manufactured from 1 May 1983 with an unladen weight exceeding 1,020kg and where the distance between the centres of any two consecutive axles exceeds 3m; or in the case of a semitrailer, where the distance between the centre of the kingpin position and the centre of the foremost axle exceeds 4.5m.
Semi-Trailers manufactured before 1 May 1983 which have a design gross weight exceeding 26,000kg and which form part of an articulated vehicle with a design gross train weight exceeding 32,520kg and where the distance between the centre of the kingpin and the centre of the foremost axle exceeds 4.5m. Where more than one kingpin is fitted it is the distance from the rearmost position which is taken into account.
Categorisation of Defects April 08 11
1
IM 9 Sideguards, Rear Under-run Part 1: Public Service, Heavy GoodsDevices & Bumper Bars and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
Sideguards - Exemptions • A vehicle or trailer constructed so that
it can be unloaded by part of the vehicle being tipped sideways or rearwards.
• A vehicle or trailer designed solely for use in connection with street cleaning, the collection/ disposal of refuse or the contents of gullies/ cesspools. (Skip carrying vehicles are classed as refuse vehicles and as such are exempt).
• A trailer specially designed and constructed, and not merely adapted, to carry round timber, beams or girders, being items of exceptional length.
• Tractor units. • A vehicle or trailer specially designed
and constructed,and not merely adapted to carry other vehicles loaded onto it from the front or rear. (Vehicles with a standard flat body fitted with a "beaver tail" are not exempt).
• A trailer with a load platform which is not more than 750mm from the ground throughout that part of its length under which a sideguard would have to be fitted.
• A semi-trailer incorporating a sliding bogie.
April 08 VOSA 12
Part 1: Public Service, Heavy Goods IM 9 Sideguards, Rear Under-run and Agricultural Vehicles Devices & Bumper Bars
1
Description of Defect Severity of Defect Action Notes
• A rigid motor vehicle or trailer designed for and constructed for the special purpose of carrying long (but not exceptionally long) timbers from an off road location in a forest.
To fulfil this definition the vehicle must meet the following criteria:
• It must be of skeletal construction. • It must have a minimum of two upright
side supports (sidebolsters) fitted to each side of the vehicle.
• It must not be fitted with a load platform, other than chassis rails, cross bearers and the minimum amount of flooring necessary to protect wiring or brake line components.
It is permissible for the vehicle to be fitted with the following:
• Loading equipment i.e. a loading crane or similar device.
• Cross bearers that do not have upright side supports.
Note:- This list is not exhaustive but covers the vehicles likely to be encountered.
Categorisation of Defects April 08 13
1
IM 9 Sideguards, Rear Under-run Part 1: Public Service, Heavy GoodsDevices & Bumper Bars and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
Under-run - Application Motor Vehicles with a design gross weight exceeding 3,500kg and first used from 1 April 1984; or Trailers manufactured from 1 May 1983 with an unladen weight exceeding 1,020kg.
Under-run - Exemptions • Tractor units. • A vehicle or trailer fitted at the rear
with apparatus specially designed for spreading material on a road.
• A vehicle or trailer so constructed that it can be unloaded by part of the vehicle being tipped rearwards.
• A vehicle or trailer specially designed and constructed, and not merely adapted, to carry other vehicles loaded onto it from the rear. (Vehicles with a standard flat body fitted with a "beaver tail'' are not exempt).
• A trailer specially designed and constructed, and not merely adapted, to carry round timber, beams or girders, being items of exceptional length.
• A vehicle or trailer fitted with a tail lift so constructed that a lift platform, with a minimum length of 1m, forms part of the floor of the vehicle.
• A vehicle specially designed,and not merely adapted, for the carriage and mixing of concrete.
Note:- This list is not exhaustive but covers the vehicles likely to be encountered.
April 08 VOSA 14
IM 10 Part 1: Public Service, Heavy GoodsSpare Wheel & Carrier and Agricultural Vehicles
Description of Defect
1
Severity of Defect Action Notes
Spare wheel insecure
Spare wheel carrier insecure or fractured Detachment imminent
Otherwise than above
Detachment imminent and likely to fall from the vehicle
Otherwise than above
I
IN
I
IN
April 08 VOSA 16
Part 1: Public Service, Heavy Goods IM 11 and Agricultural Vehicles Vehicle to Trailer Coupling
Description of Defect Severity of Defect Action Notes
Coupling on Vehicle
Deformed or cracked pin jaw, hook or ball
Mounting of jaw, hook or ball to chassis insecure
Locking device missing, inadequate, damaged or ill-fitting
Worn pin, jaw or hook
Ball excessively worn
Trailer security adversely affected
Failure or detachment likely
Locking device ineffective
Otherwise than above
Thickness of metal at any point reduced to 2/ 3 or less of its original thickness and trailer attached.
No trailer attached
Worn to such an extent that the safe coupling of the trailer is unlikely to be achieved
Otherwise than above
I
I
I
D
I
D
I
D
Categorisation of Defects April 08 17
1
IM 11 Part 1: Public Service, Heavy GoodsVehicle to Trailer Coupling and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Coupling on Vehicle
Fifth wheel attachment to chassis insecure
Fifth wheel jaw excessively worn or out of adjustment
Safety locking device (e.g. chain and clip) missing/ not operating
Excessive wear in or insecurity of any member or securing device
Security spring weak or broken
A load bearing part of the coupling cracked
Relative movement between chassis and coupling to the extent that coupling failure or detachment likely
Fifth wheel insecure (See Notes 1 and 2)
Otherwise than above
Worn to such an extent that the trailer king pin might not be securely held (See Notes 2 and 3)
Otherwise than above
(See Note 4)
Failure or detachment likely
Otherwise than above
Broken
Weak
Failure or detachment likely
Otherwise than above
I
D
IN
I
D
D
I
D
I
D
I
D
1. In certain designs the fifth wheel coupling position can be adjusted or is spring loaded on the chassis.
2. A certain amount of movement between tractor unit and trailer is permissible. The acceptable amount varies with the make of vehicle.
3. The term ‘jaw’ includes multi-towing eyes.
4. Some couplings do not require a safety locking device. Action must only be taken where there is clear evidence that a device is, or has been, fitted.
April 08 VOSA 18
Part 1: Public Service, Heavy Goods IM 11 and Agricultural Vehicles Vehicle to Trailer Coupling
1
Description of Defect Severity of Defect Action Notes
Coupling on Trailer
Draw bar cracked or deformed Seriously cracked or fractured I
So seriously deformed that use would cause danger
I
Otherwise than above IN
Mounting of draw bar to trailer insecure Failure or detachment likely I
Otherwise than above D
Draw bar eye or ball socket deformed, cracked or excessively worn
Trailer security affected
Otherwise than above
I
D
Locking device missing, inadequate, damaged or ill-fitting
Locking device ineffective
Otherwise than above
I
D
A safety device missing or not operative - I
King pin attachment excessively worn, cracked or insecure
- I
Worn operating member Detachment likely I
Otherwise than above IN
Worn draw bar attachment pins and brackets
The thickness of metal at any point reduced to 2/ 3 or less of its original thickness
I
Significant reduction in thickness D
Categorisation of Defects April 08 19
IM 12 Trailer Parking and Emergency PPaarrtt 1:1: Public SerPublic Service,vice, HeaHeavy Goodsvy GoodsBrakes and Air Line Connections and Agand Agriculturricultural Val Vehicehiclesles
Description of Defect Severity of Defect Action Notes
1
Parking Brake Operation and 1. This applies to brake systems that Performance use a ratchet and pawl mechanism
and means that, when the brake is Parking brake does not operate on at - I fully applied, there is not sufficient least two road wheels further movement of the lever
because it is at the end of its working Brake cannot be set with trailer either - I travel on the ratchet. Some foreign coupled to, or uncoupled from, the trailers will not be fitted with parking drawing vehicle brakes.
Brake mechanism fractured, insecure, Mechanism fractured or defective to such I excessively worn or badly corroded an extent that the brake is inoperative or
failure is likely
Detachment of brake mechanism imminent I
Otherwise than above D
Insufficient reserve travel on brake lever Brake efficiency impaired I (See Note 1)
Otherwise than above D
April 08 VOSA 20
PPaarrtt 1:1: Public SerPublic Service,vice, HeaHeavy Goodsvy Goods IM 12 Trailer Parking and Emergency and Agand Agriculturricultural Val Vehicehiclesles Brakes and Air Line Connections
1
Description of Defect Severity of Defect Action Notes
Trailer Emergency Brake
Trailer brakes are not applied automatically when red (emergency) brake line is disconnected. (See Notes 2, 3, 4 and 5)
Air Line Connections
- I
2. Before starting this test, make sure the air reservoirs on the tractor are fully charged. With tractor unit parking brakes ON and trailer parking brakes OFF, ask the driver to disconnect the RED (emergency) line brake connector between tractor and trailer.
Any brake line on the drawing vehicle fitted with a manual tap (See Note 6)
Preventing the correct operation of a braking system
Otherwise than above
I
D
3. In most cases, the application of the trailer brakes can be checked by observing the actuation of the trailer brake levers.
Service brake line operating adaptor providing inadequate lift or not fitted
Service (yellow) line on a unit to trailer combination not connected (See Note 7)
Preventing the correct operation of the braking system
Otherwise than as above
-
I
D
I
4. The red line connector must be reconnected by the driver after this inspection.
5. Agricultural vehicles driven at not more than 20mph might not be fitted with emergency brake lines. This is acceptable.
6. This applies to all trailers and to drawing vehicles first used on or after 1 April 1989. This action should not be applied to foreign vehicles unless affecting the correct operation of the brakes.
7. This includes combinations fitted with EBS braking systems.
Categorisation of Defects April 08 21
IM 13 PPaarrtt 1:1: Public SerPublic Service,vice, HeaHeavy Goodsvy GoodsTrailer Landing Legs and Agand Agriculturricultural Val Vehicehiclesles
1
Description of Defect Severity of Defect Action Notes
Trailer Landing Legs
Attachment of landing leg insecure
Pad, wheel, or handle insecure
Detachment likely
Otherwise than above
Detachment likely
Otherwise than above
I
IN
I
IN
April 08 VOSA 22
PPaarrtt 1:1: Public SerPublic Service,vice, HeaHeavy Goodsvy Goods IM14 Spray Suppression, and Agand Agriculturricultural Val Vehicehiclesles Wings and Wheel Arches
1
Description of Defect Severity of Defect Action Notes
Wings and Wheel Arches (See Note 5)
Wing insecure (See Note 1)
Wing badly holed/ corroded/ missing/ torn/ split
Insufficient clearance between wing and tyre
Interior wheel arch holed/ corroded (See Note 4)
Obligatory spray suppression equipment insecure/ damaged/ missing/ incomplete (See Notes 2, 3, 6 and 7)
Detachment likely, or rubbing on a tyre
Otherwise than above
Presenting a risk of injury
Not acting as a complete shield having regard to the original design
Otherwise than above
Wing rubbing or likely to rub on tyre, particularly when laden, and thereby cause damage to the tyre or a danger of injury eg: fire risk, steering affected
Otherwise than above
Holed or seriously weakened
Otherwise than above
Detachment likely
Missing/ incomplete
Otherwise than above
I
IN
I
D
IN
I
IN
I
IN
I
D
IN
NOTE: THIS IM ITEM DOES NOT APPLY TO AGRICULTURAL VEHICLES NOT DRIVEN/ DRAWN AT MORE THAN 20MPH.
1. The term wing includes other similar devices.
2. Spray suppression is required for (unless specifically exempt):
• Goods vehicles exceeding 12 tonnes gross vehicle weight first used from 1 April 1986
• Trailers exceeding 3.5 tonnes gross vehicle weight, manufactured on or after 1 May 1985
• Trailers exceeding 16 tonnes gross vehicle weight with 2 or more axles.
3. The spray suppression requirements do not apply to vehicles incapable of exceeding 30mph.
4. The ‘holed’ aspect only applies to PSVs and only when it allows the ingress of water or spray from the road wheels.
Categorisation of Defects April 08 23
1
IM 14 Spray Suppression, PPaarrtt 1:1: Public SerPublic Service,vice, HeaHeavy Goodsvy GoodsWings and Wheel Arches and Agand Agriculturricultural Val Vehicehiclesles
Description of Defect Severity of Defect Action Notes
5. Forestry vehicles (with skeletal chassis and bolsters): Rigid motor vehicles are exempt spray suppression and sideguards but must have wings. Forestry semi trailers are exempt spray suppression, sideguards and wings.
6. Incomplete in this context is where a major section of the wing and/ or the whole of the spray suppression material is missing.
7. Some foreign vehicles will not have spray suppression fitted and this is acceptable.
April 08 VOSA 24
IM 15 Part 1: Public Service, Heavy GoodsCab Security and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Cab Security
Cab not mounted securely on the chassis or mountings defective (See Note 1)
A retention and/ or locking device on a forward tilting cab defective or missing
Defective attachment of wind deflector to cab roof
Driving control likely to be affected
Driving control not likely to be affected
A significantly defective mounting
Otherwise than above
If only one locking device fitted
If more than one device is fitted and at least one is serviceable
Detachment likely
Otherwise than above
I
D
D
IN
I
D
I
IN
1. Some vehicles are fitted with tilt cabs or cabs with flexible mountings, movement of which is a design feature. This is not to be confused with excessive wear or insecurity.
April 08 VOSA 26
Part 1: Public Service, Heavy Goods IM 16 and Agricultural Vehicles Driver and Passenger Doors
1
Description of Defect Severity of Defect Action Notes
PSV Passenger Doors (See Note 1) 1. The term "door" in this context includes entrance and exit doors and
Door missing (See Note 1) - I emergency exits including emergency windows.
Door jammed/obstructed/ cannot be Jammed, obstructed, cannot be opened or I 2. In the case of a driver’s door, this opened from either the inside or outside. deliberately secured so that it cannot be action is only appropriate if it is the
opened. (See Notes 2 and 4) sole means of access. Some sliding type driver’s doors are not designed
Any emergency break glass window with D to be retained in the open position. breaking device missing 3. Vehicles first registered before 1 April
1959 need not have a device that Any emergency break glass window or I isolates the door gear from the door, the operation of which is affected by braking system. the application of advertising film (See Note 4a)
4. This will not apply to doors that: • have been permanently closed off
as part of an officially agreed Door cannot be retained in the closed position
- I modification • have been locked to safeguard the
vehicle and its contents while left
Door hinges/ catches/ pillar worn/ loose/ Door is very difficult to shut or is likely to fly I
unattended • are on a vehicle travelling empty
and where the driver can produce a insecure/ weakened open key to unlock the door.
4a. This action will be appropriate only if Otherwise than above IN the door has been sealed closed or,
in the case of a break glass window, Sliding door jammed/ likely to become Jammed or likely to become displaced I the film has not been broken around displaced/ is not retained in the open or (See Notes 2 and 4) the bead. closed position 5. It is in order to operate an
Otherwise than above IN "emergency" control before applying manual pressure to open a power
Door holding device missing/ ineffective - IN operated door.
Door check device missing/ ineffective - IN
Categorisation of Defects April 08 27
IM 16 Part 1: Public Service, Heavy GoodsDriver and Passenger Doors and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
PSV Passenger Doors (See Note 1)
Door stiff or fails to operate Unable to fully open or close
Otherwise than above
I
IN
6. Sensitive door edges are required onPSVs manufactured on or after 14 May 1990 or first used on or after 1October 1990 where the whole of the door opening is more than 500mmbehind the driver’s seat.
Door operation affects braking system
Power operated door cannot be opened manually
Door sensitive edge or other safety device not working
"Door open" warning device inoperative
Draught excluder insecure
Repeated operation of the doors depletes the braking system air/ vacuum below the pressure/ vacuum threshold at which the circuit protection valve should operate (See Note 3)
(See Note 5)
Where required (See Notes 6, 7 and 8)
Otherwise than above
Where required (See Note 9)
Otherwise than above
Likely to cause obstruction or injury
Otherwise than above
I
I
I
IN
I
IN
I
IN
7. A safety system for preventing apassenger from being trapped mustbe provided on all power operateddoors without a soft rubber edge.
8. Every power-operated door fitted to aminibus must cease closing whenmeeting a resistance and either reopen or be capable of being openedmanually.
9. Warning devices are only required on
• Schedule 6 minibuses which do not have two stage slam locks
• Large buses with more than 20passenger seats which are certifiedfor one person operation and usedon local services on each emergency door and hingedemergency window.
• ‘Continental’ doors (Continued)
April 08 VOSA 28
Part 1: Public Service, Heavy Goods IM 16 and Agricultural Vehicles Driver and Passenger Doors
1
Description of Defect Severity of Defect Action Notes
PSV Passenger Doors (See Note 1)
Door operation severe
Obligatory markings or fittings missing/ damaged/ ineffective
Any normally fitted exit door handle guard missing
Likely to cause injury
Otherwise than above
-
-
I
IN
IN
IN
9. (Continued)• Vehicles first used on or after 1
October 1990 with power operateddoors which are more than 500mm to the rear of the driver’s seat (typicallycentre doors). In this case the warningmust be visual.
• Any external door or hinged exit(including any emergency exit) which isoutside the driver’s direct line of sighton a vehicle certified on or after 1 January 1997. This does not apply to adoor of a minibus if that door has a two stage lock.
Cab Doors
Driver’s external door jammed/ obstructed/ will not fasten/ difficult to open
Door hinges, catches or pillars in such a condition that the door is difficult to close or could fly open inadvertently (See Note 12)
Sliding door which cannot be secured in the open or closed position and/ or runners or tracks so badly worn or defective that the door cannot be opened and closed without excessive
Likely to impede driver in an emergency or to fly open inadvertently (See Notes 10 and 11)
Otherwise than above
Door likely to fly open
Otherwise than above
Driver’s door cannot be secured
Otherwise than above
I
IN
I
IN
I
IN
• On any emergency door or floor hatchon a Bus Directive or ECE regulationvehicle. This must be an audible device
• On any hinged emergency windowwhich is not clearly visible to the driveron a Bus Directive or ECE regulationvehicle. This must be an audible device
10. Where the driver’s door of a PSV doubles as an emergency door(See Note 1).
11. On a HGV, if one door is deliberately rendered inoperative, then it must beconsidered to be an integral part of the cab.
12. The cab doors and fasteningdevices on agricultural vehicles aresometimes crudely designed. Before applying these standards Examiners must take account of the original
effort (See Note 12) design of the component. The potential speed of the vehicle,the likelihood of a door flying open
Categorisation of Defects April 08 29
1
IM 16 Part 1: Public Service, Heavy GoodsDriver and Passenger Doors and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes 12. (Continued)
and whether it would be likely toswing beyond the edge of thevehicle must also be considered.
13. On Bus Directive and ECE Regulationvehicles, there might not be a primaryemergency exit, if the vehicle has twoservice doors. On Bus Directive vehicles, the primary emergency exitmay be power operated; floor hatchesmay be used as emergency exits.
14. Bus Directive: This means a bus or coach which meets the requirements ofthe Bus Directive EC 2001/85. Thevehicle may have a full type approval ormay have been inspected to therequirements of the directive. Thetechnical print for the vehicle will indicate“Bus Directive” vehicles.
15. ECE regulation vehicle: This means abus which has been built or approved toECE regulation 36 (buses with morethan 22 passengers), ECE regulation 52(buses with not more than 22passengers) or ECE regulation 107(Double Deck buses).
April 08 VOSA 30
IM 17 Part 1: Public Service, Heavy GoodsDriver’s Accommodation and Steps and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
Driver’s Cab/ Area and Fittings
Driver’s cab floor insecure/ badly Affects driving control or safety of driver I weakened
Otherwise than above IN
Driver’s cab step or step ring on a wheel Likely to cause injury to users or become I insecure/ badly weakened/ damaged/ detached worn
Otherwise than above IN
Step has a jagged edge Likely to cause injury to a person near the I vehicle
April 08 VOSA 32
Part 1: Public Service, Heavy Goods IM 18 and Agricultural Vehicles Driver’s Seat
Description of Defect Severity of Defect Action Notes
Driver’s Seat
Driver’s seat loose on its mounting, frame fractured, seriously weakened or otherwise defective
Driver’s seat adjustment inoperative/ badly worn
Seat so loose/ weakened/ or in such condition that it could cause the driver to lose control of the vehicle
Otherwise than above
Seat likely to move inadvertently or cannot be located
I
IN
I
Categorisation of Defects April 08 33
1
IM 19 Security of Body, Containers and Part 1: Public Service, Heavy GoodsCrane Support Legs and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Security of Body
Body components and fixings (eg twist-locks) loose/ fractured/ missing
Excessive displacement of the body relative to the chassis
Security of Containers
Container fastening device missing/ insecure/ incomplete/ seized/ not fitted with a secondary locking device/ not capable of adequately securing a container (See Note 3)
Insecurity of body components or cross or longitudinal members to the chassis, likely to affect safe carriage of passengers or load
Fixings insecure or defective but not affecting safe carriage of passengers or load (See Note 1)
Likely to lead to loss of control
Otherwise than above (See Note 2)
Likely to affect the overall security of a container
A container fastening insecure and likely to detach
A container fastening missing when the other of a matched pair is present
A container fastening incomplete/ seized / without a secondary locking device/ ineffective
Otherwise than above
I
IN
I
D
I
I
D
D
IN
1. The presence of defective items does not necessarily mean that the body is to be regarded as so insecurely fixed as to be dangerous.
The cumulative effect of any defects found, or their effect on other items, is the criterion to be used when judging this item.
2. Most designs of vehicles have a certain amount of freedom between the body and chassis to allow for flexing. This must not be confused with insecurity.
3. In the case of a dual purpose flat bed, if all the twist locks have been removed then it is not to be regarded as defective.
April 08 VOSA 34
Part 1: Public Service, Heavy Goods IM 19 Security of Body, Containers andand Agricultural Vehicles Crane Support Legs
1
Description of Defect Severity of Defect Action Notes
Support bolster or structure insecure/ cracked/ corroded or damaged
Support bolster not fitted with locking pins or other securing method incorporating an effective locking device
Crane Support Legs
Crane Support Leg insecure/ retaining device missing/ insecure or in such a condition that it will not adequately retain the leg (See Notes 4 and 5)
Likely to affect the overall security of a container
Container mounting point unlikely to be secured or supported by it
Otherwise than above
Likely to affect the overall security of a container
Container mounting point unlikely to be secured or supported by it
Otherwise than above
Insecure or likely to extend
Retaining device missing or incapable of operating as designed
Otherwise than above
I
D
IN
I
D
IN
I
D
IN
4. These criteria can be extended beyond those fitted to vehicles with cranes to any vehicle equipped with stabilizing/support legs.
5. This guidance applies where retaining devices were originally fitted. An alternative retaining device is acceptable provided the support leg is adequately secured.
Categorisation of Defects April 08 35
Part 1: Public Service, Heavy Goods IM 20 and Agricultural Vehicles Condition of Body
1
Description of Defect Severity of Defect Action Notes
Body Panelling
Exterior body panel damaged/ missing/ protruding/ insecure
Any embellishment protruding/ damaged/ insecure (Specify component)
Part of body designed to carry or contain the load missing or damaged
Likely to become detached or to cause injury or permit the load to be shed or leaked
Otherwise than above (See Notes 1 and 2)
Likely to become detached and/ or cause injury
Otherwise than above
Load likely to become detached or to cause injury or permit it to be shed or leaked
I
IN
I
IN
I
1. The presence of some defects does not necessarily mean that the body is in such a condition that it would be dangerous for other road users. The cumulative effect of any defects found, or their effect on other items, is the criterion to be used when judging this item.
2. Any superficial damage that does not affect the strength of the component is not to be regarded as a defect.
Otherwise than above IN
Categorisation of Defects April 08 37
IM 20 Part 1: Public Service, Heavy GoodsCondition of Body and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
PSV Flap Type Doors (See Note 3)
Any flap/ door catch defective/ catch missing/ insecure
Any flap/ door protruding when closed/ exposing sharp (jagged) edges
Flap/ Door check device missing/ ineffective
Detachment likely or is likely to fly open
Otherwise than above
Likely to cause injury or damage
Otherwise than above
Door opening too far and likely to obscure obligatory lights
Otherwise than above
I
IN
I
IN
D
IN
3. These standards do not apply to small access flaps eg. fuel filler or coolant filler access flaps.
April 08 VOSA 38
Part 1: Public Service, Heavy Goods IM 20 and Agricultural Vehicles Condition of Body
1
Description of Defect Severity of Defect Action Notes
PSV Luggage Compartments
Water leakage into luggage compartment
Luggage compartment damaged/ dirty
Luggage compartment floor damaged/ deteriorated/ weak
Luggage compartment door catch defective/ catch missing/ insecure
Luggage compartment door protruding when closed/ exposing sharp (jagged) edges
Luggage compartment door holding device missing/ ineffective (See Note 5)
Luggage compartment door check device missing/ ineffective
Likely to soil or damage passengers’ luggage (See Note 4)
Otherwise than above
Likely to soil or damage passengers’ luggage (See Note 4)
Otherwise than above
Floor likely to collapse
Otherwise than above
Detachment likely or is likely to fly open inadvertently
Otherwise than above
Likely to cause injury or damage
Otherwise than above
Door does not remain in the open position and is likely to close and cause injury
Otherwise than above
Door opening too far and likely to obscure obligatory lights
Otherwise than above
D
IN
D
IN
I
IN
I
IN
I
IN
I
IN
D
IN
4. This will apply only where luggage is being carried in the compartment at the time of inspection.
5. Devices to hold flaps/ doors open are required only where they are provided to give access to luggage compartments. Similar flaps or doors provided for other purposes e.g. engine or spare wheel access are not required to have them.
Categorisation of Defects April 08 39
IM 21 Part 1: Public Service, Heavy GoodsInterior of Body and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
PSV Floor, Gangways, Steps and Stairs
Floor/ gangway/ passageway/ steps/ Holed or likely to collapse I stairways/ retractable steps/ platforms or floor traps weakened (State location) Otherwise than above IN
Retractable step not retracting - I
Floor trap weakened/ damaged/missing Likely to collapse or likely to cause I obstruction or injury
Otherwise than above IN
Floor trap locking device defective Trap insecure and likely to lift I
Otherwise than above IN
Floor/ step/ stair/ stair covering Likely to cause obstruction or injury I torn/ lifting/ bubbling
Otherwise than above IN
Floor/ step/ stair/ treadplate/ moulding Non slip surface worn smooth and/ or lifting I badly worn/ lifting and likely to cause obstruction or injury
Otherwise than above IN
Step/ stair insecure/ weakened/ Likely to cause injury or become detached I damaged/ having jagged edges/ defective Otherwise than above IN
April 08 VOSA 40
Part 1: Public Service, Heavy Goods IM21 and Agricultural Vehicles Interior of Body
1
Description of Defect Severity of Defect Action Notes
PSV Passenger Entrance 1. Steps or platforms forming part of an emergency exit are not required to be
Entrance floor mat badly worn/ of Likely to trip passengers I illuminated. incorrect size
Otherwise than above IN
PSV Artificial Lighting
Interior lamp missing/ inoperative - IN
Inadequate illumination at Constituting a risk of injury I entrance/ exit/ step/ stair (See Note 1)
Otherwise than above IN
Categorisation of Defects April 08 41
IM 21 Part 1: Public Service, Heavy GoodsInterior of Body and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
PSV Passenger and Crew Seats 2. Any surface contamination of the seat covering should not take into account
Passenger seat incorrectly spaced or a Access to an exit is obstructed D dust in the seat fabric or loose crew seat which encroaches on the surface dust. minimum gangway width and does not Otherwise than above IN fold away automatically (See Note 4) 3. Applicable if due to an accidental
spillage. Seat insecure Likely to become displaced I
4. Some older coaches have been Otherwise than above IN certified with crew seats with latches
to operate before the seat will fold. Seat covering slashed/ torn - IN Prohibition action will not be
appropriate in these cases. If there is Seat frame fractured Seat failure or displacement likely I any doubt, take Inspection Notice
action only and advise. Otherwise than above IN
Passenger seats generally contaminated Likely to soil clothing (See Note 2) D or dirty
Isolated seat or group of seats (See Note 3) IN contaminated
Seat damaged Likely to cause injury I
Likely to tear clothing D
Otherwise than above IN
April 08 VOSA 42
Part 1: Public Service, Heavy Goods IM 21 and Agricultural Vehicles Interior of body
1
Description of Defect Severity of Defect Action Notes
PSV Interior Fittings 5. Roof lights mean translucent panels fitted in the body roof.
Parcel rack insecure/ damaged/ holed Likely to collapse or to permit luggage to fall I on passengers 6. Large buses used solely as local
service vehicles need not carry a first Otherwise than above IN aid kit.
Guard not fitted to parcel rack end Items likely to fall onto driver I 7. PSVs and Schedule 6 minibuses only.
Interior stanchion/ guard rail/ grab rail Likely to detach under weight of passengers I 8. This inspection also applies to missing/ insecure/ damaged and/ or cause injury articulated PSV bellows.
Otherwise than above IN
Missing grab strap IN
Roof light insecure/ missing Likely to become displaced and fall onto I occupants (See Note 5)
Otherwise than above IN
Fire extinguisher missing/ empty/ (See Note 7) IN defective/ wrong type e.g. powder
First aid equipment missing/ incomplete (See Notes 6 and 7) IN
Interior body panel damaged/ holed/ Likely to cause injury to any person I missing/ protruding/ insecure (See Note 8)
Otherwise than above IN
Legal writing/ warning notices missing/ - IN illegible
Categorisation of Defects April 08 43
IM 21 Part 1: Public Service, Heavy GoodsInterior of body and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
PSV Interior Fittings
Passenger communication device missing/ inoperative
Engine cover missing/ insecure
Engine compartment sound deadening material insecure/ oil soaked
Graffiti/ contamination on an internal surface (State location)
Other equipment insecure (e.g. TV, video, coffee bar etc)
Where driver is in a separate compartment (See Note 9 and 10)
Otherwise than above
Missing from saloon or driver’s compartment
Insecure and fumes can enter cab or saloon
Otherwise than above
Likely to become displaced or cause fire hazard
Otherwise than above
Likely to soil clothing
Other unauthorised writing or drawing
Otherwise than above
Likely to become detached and/ or cause injury
Otherwise than above
I
IN
I
D
IN
I
IN
D
IN
IN
I
IN
9. Bells/ buzzers/ visual warnings are not required on buses with less than 13 passenger seats or Schedule 6 minibuses but are required on Non-Schedule 6 minibuses with 13 or more passenger seats. All bus directive and ECE regulation vehicles which carry standing passengers must have at least one illuminated sign to indicate to passengers the bus is stopping. Some communication devices will sound once only until reset by passenger doors opening or similar.
10. Bus Directive and ECE Regulation vehicles, which are not authorised for the carriage of standing passengers, do not require passenger to driver communication devices.
April 08 VOSA 44
Part 1: Public Service, Heavy Goods IM 21 and Agricultural Vehicles Interior of body
1
Description of Defect Severity of Defect Action Notes
Ventilation Equipment (See Note 11)
Opening windows cannot be opened
Forced air ventilation equipment missing / inoperative/ ineffective (See Note 12)
Canopy ventilator defective
50% or more opening windows cannot be opened
50% or more forced air ventilation outlets missing/ inoperative/ ineffective
Otherwise than above
Canopy insecure and detachment likely
Seized open and not protecting passengers from elements
Seized closed and no alternative ventilation available
Otherwise than above
D
D
IN
I
D
D
IN
11. Where more than one means of ventilation is provided an assessment will have to be made as to whether more than 50% of the total ventilation of all types is ineffective. If in doubt take advisory action only.
12. Some forced air ventilation systems will not operate unless the engine is running and the alternator is charging.
Categorisation of Defects April 08 45
IM 21 Part 1: Public Service, Heavy GoodsInterior of body and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Accessibility Features
Wheel Chair Spaces
Rearward Facing Wheelchairs (See Note 13)
Stanchion or retractable rail relating to the wheelchair area missing, insecure or damaged
Partition or panel relating to the wheelchair area missing, damaged or insecure
Unrestrained wheelchair padded backrest insecure or damaged
Likely to detach if used or cause injury to any person
Otherwise than above
Panel likely to fall away and/or cause injury to any person
Otherwise than above
Insecure and likely to fail when loaded or cause injury to any person
Otherwise than above
I
IN
I
IN
I
IN
13. Apply the standards in this section for vehicles that have not been issued with an Accessibility Certificate or Disability Discrimination Act special authorisation.
April 08 VOSA 46
Part 1: Public Service, Heavy Goods IM 21 and Agricultural Vehicles Interior of body
1
Description of Defect Severity of Defect Action Notes
Forward Facing Wheelchairs (See Note 14)
Occupied wheelchair or user restraint fixings missing, ineffective, deteriorated or insecure (See Note 14)
Floor fixings loose or projecting
Missing, ineffective, incapable of performing its intended function or likely to detach if loaded
Otherwise than above
Serious risk of passengers tripping or being injured
Otherwise than above
I
IN
I
IN
14. If missing or ineffective but other wheelchair spaces are available and free of defects an exemption may be issued allowing the vehicle to complete its journey. A condition will be imposed specifying the number of wheelchair passengers permitted.
Categorisation of Defects April 08 47
IM 21 Part 1: Public Service, Heavy GoodsInterior of body and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Wheelchair or user restraint system missing, damaged or defective
Boarding Devices- Lifts and Ramps
A lift or ramp severely weakened, with sharp edges or other protrusions
Lift or ramp cannot be secured in the stowed position
Incapable of being easily operated in an emergency.
Otherwise than above
Likely to fail or cause injury to any person
Otherwise than above
Posing a risk of injury to any person
Otherwise than above
I
IN
I
IN
I
IN
April 08 VOSA 48
Part 1: Public Service, Heavy Goods IM 21 and Agricultural Vehicles Interior of body
1
Description of Defect Severity of Defect Action Notes
Powered Lifts and Ramps
Defective in operation Posing a risk of injury to any person
Otherwise than above (See Note 15)
I
IN
15. An inoperative powered ramp or lift that does not pose danger to any person or road user should be subject to inspection notice action. If the lift or ramp is permanently disabled VTP5 Notifiable Alteration action is required allowing a revised Carrying Capacity Authorisation to be issued.
Categorisation of Defects April 08 49
IM 22 Part 1: Public Service, Heavy GoodsDriver’s Mirrors and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Mirrors
External rear view mirror and/ or glass missing/insecure/damaged (See Note 3)
Interior rear view mirror/ missing/ defective/ insecure (See Note 3)
A periscope defective
If no adequate view to the rear (See Note 1)
External mirror likely to become detached
Otherwise than above
Likely to become detached and fall onto driver/ occupants
Missing or unusable (See Note 2)
Otherwise than above (See Note 2)
Likely to become detached and fall onto driver/ occupants, or otherwise in such condition as to cause injury
Otherwise than above
I
I
IN
I
D
IN
I
IN
1. HGVs first used before 1 April 1985 (PSV: 1 April 1983) must have either one offside exterior mirror and one interior mirror, or an exterior mirror on each side.
HGVs first used on or after 1 April 1985 (PSV: 1 April 1983) must have an exterior mirror on each side.
Rigid HGVs first used on or after 1 October 1988 exceeding 12 tonnes GVW must have an exterior mirror on each side, plus one close proximity mirror on the nearside.
Articulated HGVs first used on or after 1 October 1988 exceeding 12 tonnes GVW must have an exterior mirror on each side, plus one close proximity mirror on the nearside, plus one wide angle mirror on the nearside.
2. A missing or unusable interior mirror must be regarded as a defect only when the vehicle has no external rear view mirror on the nearside.
3. Mirrors are not required on agricultural vehicles driven at not more than 20mph or any agricultural vehicle first used before 1 June 1986.
April 08 VOSA 50
Part 1: Public Service, Heavy Goods IM 23 and Agricultural Vehicles Glass and View of the Road
Description of Defect Severity of Defect Action Notes
View to the front
Driver’s view to the front impaired having regard to the original design of the vehicle (See Note 1)
Any object seriously impairing driver’s view through the area swept by the windscreen wipers
Otherwise than above
I
IN
1. Reversing monitors and navigation screens may be acceptable, provided they do not impair the drivers view to the road.
Categorisation of Defects April 08 51
1
IM 23 Part 1: Public Service, Heavy GoodsGlass and View of the Road and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
Windscreen and Windows 2. On vehicles first used before 1 January 1959, if glass is fitted to
Windscreen cracked/ scratched/ Driver’s view of the road seriously I windscreens and windows facing to discoloured impaired/ presents a danger to occupants of the front on the outside of any motor
the vehicle/ detachment likely vehicle, except the upper deck of a double decked vehicle, it must be
Otherwise than above IN safety glass.
Windscreen not of safety glass (See Notes 2, 3, 4 and 5) I 3. On PSVs first used between 1 January 1959 and 31 May 1978, if glass is
Driver’s side window not of safety glass (See Notes 2, 3, 4 and 5) D fitted to windscreens or any windows on the outside it must be safety glass.
PSV driver’s interior door/ screen not of (See Notes 3, 5, 6 and 8) D safety glass or of a safety glazing 4. Safety glass on vehicles first used material before 1 June 1978 need not be
marked as such. Where markings PSV window not of safety glass or of a (See Notes 2, 3, 4 and 5) D have been applied, these can fade safety glazing material with time.
PSV window glazing missing/ insecure/ Missing, detachment likely and/ or presents I 5. On vehicles first used on or after 1 cracked a danger June 1978, windscreens and other
windows wholly or partly on either side Otherwise than above IN of the driver’s seat must be of
specified safety glass. All other Relevant vehicle (See Note 4) with glass - IN windows must be specified safety not marked with an acceptable mark. glass or glazing.
Windscreen and front side windows Average light transmission <30% I 6. On PSVs first used on or after 1 April excessively tinted 1959 and before 1 April 1988,
Average light transmission >30% <45% D transverse windows or transparent partitions not of safety glass or safety
Average light transmission >45% <65% IN glazing must be adequately protected against breakage should a passenger be thrown against them.
April 08 VOSA 52
Part 1: Public Service, Heavy Goods IM 23 and Agricultural Vehicles Glass and View of the Road
1
Description of Defect Severity of Defect Action Notes
PSV Windows
Window louvres cracked/ broken/ insecure
Weather strip damaged/ deteriorated
Window dirty
Detachment likely and/ or presents a danger
Otherwise than above
-
Affecting vision and/ or light
I
IN
IN
IN
7. On PSVs first used on or after 1 April 1988, all transverse windows or transparent partitions must be of safety glass or safety glazing.
On PSVs first used before 1 April 1959, transverse windows or transparent partitions not of safety glass or safety glazing must be adequately protected against breakage if they face transverse seats.
8. Safety glazing is permissible for windows forming all or part of a door fitted in the interior of a PSV at the side of the driver’s seat so as to form a compartment for the driver.
Categorisation of Defects April 08 53
IM 24 Part 1: Public Service, Heavy GoodsAccessibility Features and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
See Note 1
Wheel Chair Spaces
Sign or instruction indicating the direction the wheelchair and user should face during travel missing or deteriorated
Safety instructions explaining the use of the wheelchair space and restraint systems missing or deteriorated (not Annex VII vehicles)
Missing or illegible
Missing or illegible
IN
IN
1. The standards in this section apply only to vehicles issued with an Accessibility Certificate or Special Authorisation. As an alternative to schedules 1, 2 or 3 some vehicles with accessibility certificates will be Bus Directive vehicles and will include compliance with Annex VII of the directive.
Annex VII means Annex VII to Bus Directive 2001/85/EC and ‘Annex VII vehicle’ means a Bus Directive vehicle required to comply with Annex VII.
ECE regulation vehicle means a bus which has been built or approved to ECE regulation 36 (buses with more than 22 passengers), ECE regulation 52 (buses with not more than 22 passengers) or ECE regulation 107 (double deck buses).
This information is noted on the technical record of the vehicle. For vehicles not issued with such certificates or where it is not known apply the standards in IM21.
April 08 VOSA 54
Part 1: Public Service, Heavy Goods IM 24 and Agricultural Vehicles Accessibility Features
1
Description of Defect Severity of Defect Action Notes
Rearward Facing Wheelchairs
Padded backrest missing, insecure or damaged or other device supplied to support the wheels or the back of the wheelchair missing or damaged (See Note 2)
Stanchion or retractable rail relating to the wheelchair area missing, insecure or damaged
Partition or panel relating to the wheelchair area missing, damaged or insecure
Insecure and likely to fail when loaded; missing and likely to cause injury to any occupant
Otherwise than above
Likely to detach if used or cause injury to any person or danger caused by absence
Missing
Otherwise than above
Panel likely to fall away and/or cause injury to any person or danger caused by absence
Missing
Otherwise than above
I
IN
I
D
IN
I
D
IN
2. On Annex VII vehicles a backrest where fitted need not be padded and as an alternative to a backrest a device which acts as a support for the wheels of the wheelchair may be permitted.
Categorisation of Defects April 08 55
IM 24 Part 1: Public Service, Heavy GoodsAccessibility Features and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Forward Facing Wheelchairs (See Note 3)
Wheelchair or user restraint fixings missing/ ineffective/ deteriorated or insecure
Floor fixings loose or projecting
Wheelchair or user restraint system missing/ damaged or defective
Ineffective/ incapable of performing its intended function or likely to detach if loaded
Missing (position unoccupied)
Otherwise than above
Serious risk of passengers tripping or being injured
Ineffective/ incapable of performing its intended function or likely to detach if loaded
Incapable of being easily operated in an emergency
Missing
Otherwise than above
I
D
IN
I
I
I
D
IN
3. No wheelchair user restraint for Bus Directive Annex VII vehicles if the passenger seats in the vehicle are not required to be fitted with any form of occupant restraint.
April 08 VOSA 56
Part 1: Public Service, Heavy Goods IM 24 and Agricultural Vehicles Accessibility Features
Description of Defect Severity of Defect Action Notes
Safety instructions on the use of wheelchair and/or wheelchair user restraints missing or deteriorated (Not Annex VII vehicles)
Boarding Devices - Ramps and Lifts
A lift or ramp missing, insecure or severely weakened, with sharp edges or other protrusions
Lift or ramp cannot be secured in the stowed position
Missing or illegible
Likely to fail or cause injury to any person
Missing
Otherwise than above
Posing a risk of injury to any person
Otherwise than above
IN
I
D
IN
I
IN
Categorisation of Defects April 08 57
1
IM 24 Part 1: Public Service, Heavy GoodsAccessibility Features and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Lift surface device for preventing wheelchairs from rolling off defective or missing
Contrasting band of colour along the edge of a ramp or lift deteriorated (not Annex VII lifts)
Powered Lifts or Ramps
Fails to operate by the primary means or operation presents a risk to any person
Secondary means of operation incomplete or defective (See Note 4)
Audible warning of operation inoperative (not Annex VII vehicles fitted with a lift)
Wheelchair users at risk of injury
Not capable of operating as intended
Otherwise than above
Missing or visually ineffective
Deteriorated but still visible
Posing a risk of injury to any person
Inoperative or otherwise than above
Fails to operate at all or missing
Missing or inaudible
Otherwise than above
I
D
IN
D
IN
I
D
D
D
IN
4. Examiners should be aware that the secondary means of operation can be achieved by using a portable ramp.
April 08 VOSA 58
Part 1: Public Service, Heavy Goods IM 24 and Agricultural Vehicles Accessibility Features
Description of Defect Severity of Defect Action Notes
Lamp and audible warning of operation of an Annex VII vehicle powered ramp
Portable Ramps and Powered Ramp/ Hoist secondary operation
There is not at least one portable ramp available for use where required (i.e. where there is no manual ramp, powered lift or ramp fitted and working) or no manual secondary means to operate a powered lift/ ramp
A portable ramp with no suitable stowage position
A portable ramp which cannot be safely fitted for passenger use
No warning of operation
Otherwise than above
Missing
A hazard likely to cause injury
Otherwise than above
Incapable of being fitted or if fitted not capable of performing its function
I
IN
D
I
IN
I
Categorisation of Defects April 08 59
1
IM 24 Part 1: Public Service, Heavy GoodsAccessibility Features and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Viewing Devices (See Note 5)
Driver does not have when seated in the driver's seat either directly, using mirrors or other devices a clear view of the inside and outside of the door area in which a power operated lift/ ramp is located (not applicable if the operating control is not adjacent to the lift or ramp)
Communication Devices (See Note 6)
Any device intended for wheelchair users inoperative or missing.
Any exterior communication device inoperative or missing.
The inside and outside of the door area or the lift or ramp are not visible to the driver from the driver's seat
Insecurity and likely to cause injury
Otherwise than above
Missing or inoperative
Missing or inoperative
I
I
IN
D
D
5. This is not required where the lift or ramp is in direct field of driver's vision from driving seat or where the operating control is adjacent to the lift or ramp.
6. Internally this would be at a wheelchair space or externally adjacent to the wheelchair entrance that is outside the direct view of the driver. Where the wheel chair entrance/ exit is within direct view of the driver no device is required.
April 08 VOSA 60
Part 1: Public Service, Heavy Goods IM 24 and Agricultural Vehicles Accessibility Features
1
Description of Defect Severity of Defect Action Notes
Entrance and Exit Lighting 7. Examiners should consider any other (See Note 7) artificial and natural lighting.
Lighting specifically intended for Illumination of the area so inadequate as to I wheelchair users to be able to board or pose a risk to the safety of users alight in safety is missing, inoperative or badly deteriorated. Other lighting provides sufficient illumination IN
for users
Steps/Floors/Gangways
Slip resistant material deteriorated and Users likely to loose their footing I no longer effective
Otherwise than above IN
Contrasting band of colour along the Missing D edge of a step missing or deteriorated (not Annex VII or ECE regulation Deteriorated but still visible IN vehicles)
Step projecting and/or likely to cause injury I
Folding or extendible step damaged or Cannot be stowed correctly IN not functioning correctly
Kneeling Suspension
Controls do not stop and reverse - I lowering process
Categorisation of Defects April 08 61
IM 25 Part 1: Public Service, Heavy GoodsWindscreen Wipers and Washers and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Washers and Wipers
Windscreen wiper missing/ damaged/ inoperative/ blades worn (See Note 1)
Windscreen washer not fitted/ inoperative/ system incomplete (See Notes 1, 2 and 3)
Any wiper missing, inoperative or damaged such that the driver’s view to the front is impaired
Subject to prevailing weather conditions (ie weather fine)
Otherwise than above
Vision seriously impaired
Otherwise than above
I
D
IN
I
IN
1. If the windscreen can be opened, or, by some other means, an adequate view can be obtained from the driving seat, the vehicle need not be provided with wipers or washers.
2. Washers are not required on PSVs whilst on local service duty
3. Washers are not required on agricultural motor vehicles first used before 1 June 1986 or those driven at speeds not exceeding 20mph.
April 08 VOSA 62
Part 1: Public Service, Heavy Goods IM 26 and Agricultural Vehicles Speedometer/ Tachograph
1
Description of Defect Severity of Defect Action Notes
Speedometer
Speedometer not fitted/ incomplete/ inoperative/ dial glass broken/ missing/ cannot be illuminated (See Notes 1, 2 and 3)
Tachograph
Where required, a tachograph is not fitted/ sealed/ inoperative (See Notes 2, 3 and 4)
-
Tachograph defects to be dealt with under the Transport Act (GVI70 /TE160)
IN
-
1. Vehicles first registered on or after 1 October 1937 must be fitted with a speedometer unless the vehicle is legally limited to a speed not exceeding 25mph or is incapable by reason of its construction of exceeding 25mph.
2. A tachograph may be fitted in place of a speedometer to a vehicle not within the scope of EC regulations.
3. Tachograph/ Speedometer fitment does not apply to Agricultural motor vehicles driven at not more than 20mph.
4. Examiners should be aware that if recording equipment is fitted there are situations where no offence is being committed and therefore no action should be taken. A person is not liable if it can be established that it had not been reasonably practicable for the equipment to be repaired by an approved workshop e.g. it had become defective during the journey. Drivers in these circumstances are required to keep manual records.
Categorisation of Defects April 08 63
IM 27 Part 1: Public Service, Heavy GoodsAudible Warning (Horn) and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Horn
Horn missing/ insecure/ inoperative (See Note 1)
Detachment imminent
Otherwise than above
I
IN
1. This inspection item does not apply to an agricultural vehicle driven at not more than 20mph or other motor vehicles which have a maximum speed not exceeding 20mph.
April 08 VOSA 64
Part 1: Public Service, Heavy Goods IM 28 and Agricultural Vehicles Driving Controls
1
Description of Defect Severity of Defect Action Notes
Driving Controls This Section does not apply to the condition of brake controls. IM Nos
Driving control missing/ incomplete/ Control so defective or impeded in its travel I 36, 37 and 39 apply. fractured/ damaged/ excessively that it fails to fulfil its function corroded/ impeded in its travel/ incorrectly positioned/ insecure (Specify Otherwise than above IN component)
Clutch pedal anti-slip pad loose/ If originally fitted IN deteriorated
Engine stop control inoperative - IN
Condition of Driver’s Area
Driver’s area littered with rubbish/ Liable to interfere with proper control of the I ancillary equipment vehicle
Otherwise than above IN
Categorisation of Defects April 08 65
IM 30 Part 1: Public Service, Heavy GoodsSteering Control and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
Steering Wheel 1. The maximum permissible "free" play on a steering wheel is as follows:
Excessive "free" play at steering wheel Likely to impair directional control of the I vehicle If a point on the rim of the steering
wheel moves without the road wheels Otherwise than above D moving for a distance of
Steering wheel (hub/ rim/ spokes)
(See Notes 1, 2 and 3)
Failed or failure imminent or jagged edges I • (except on rack and pinion steering)
1/ 5 of diameter of steering wheel, fractured likely to cut driver’s hand e.g. 76mm on a 380mm diameter
Otherwise than above (See Notes 4 and 5) D wheel
• (on rack and pinion steering) 1/ 30 of diameter, e.g. 13mm on a 380mm
Steering wheel (hub/ rim/ spokes) Detachment imminent I diameter wheel. Free play of up to insecure 1/ 8 of diameter, e.g. 48mm on a
Otherwise than above D 380mm diameter wheel is acceptable where the steering wheel
Steering wheel loose to column shaft - I - is placed forward from rack and pinion steering, and
Steering wheel retaining device missing - I - has a number of joints to the rack. (specify device)
2. Power steering must be checked with the engine running. While the power steering pump is working but not providing hydraulic assistance, the steering wheel play is slightly greater than with manual steering systems.
3. In some types of steering, e.g. those with universal joints or flexible couplings, there might be a certain amount of movement present that is not due to wear.
April 08 VOSA 66
Part 1: Public Service, Heavy Goods IM 30 and Agricultural Vehicles Steering Control
1
Description of Defect Severity of Defect Action Notes
Steering Column
Excessive lift or side movement of steering column
Steering column coupling excessively deteriorated/ worn/ insecure
Steering wheel/ column adjuster defective
Abnormal movement indicating failure of component parts
Otherwise than above (See Notes 3 and 6)
Failure imminent
Otherwise than above (See Notes 3 and 6)
Steering wheel/ column cannot be secured as required
Otherwise than above
I
D
I
D
I
IN
4. Cracks in the plastic covering of a spoke do not necessarily indicate that the spoke is fractured.
5. Jagged edges on the rim of a steering wheel (e.g. due to cracks in plastic covering) are a reason for action ONLY if they are likely to cut the driver’s hand.
6. Some vehicles have flexible top bearings for the steering column, in which case more than average movement is permissible.
Categorisation of Defects April 08 67
IM 33 Part 1: Public Service, Heavy GoodsSpeed Limiters and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
Speed Limiters
Speed limiter missing/ disconnected (See Note 1 and Table A for the requirements according to use, class and age of vehicle)
Speed limiter not restricting the vehicle to its legal maximum (See Notes 2 and Table A)
Evidence of intent to circumvent the speed restrictions
Unintentional non-compliance (See Note 3)
Evidence of intent to circumvent the speed restrictions
Unintentional non-compliance but applicable restricted speeds clearly exceeded (over 10 kph) (See Note 3)
I
D
I
I
1. If applicable to the vehicle type, date of first use and use (international or domestic) - See Table A.
2. Between January 2005 and January 2008 the scope of vehicles requiring speed limiters has been extended.
3. Unintentional non-compliance will include those instances provided for in regulation where the speed limiter has become defective during the current journey even if the driver is aware. Providing the available evidence indicates the driver is
Speed limiter plate missing/ defective/ showing evidence of disturbance
Unintentional non-compliance but evidence that applicable restricted speed limit is being generally complied (within 10 kph) (See Notes 3 and 5)
-
D
IN
generally complying with the applicable speed (within 10 kph) delayed prohibition action will be appropriate.
4. Some speed limiters do not require the fitting of external tamperproof devices. Action must only be taken where there is clear evidence that a device has been disturbed/removed or is defective.
Speed limiter tamper proof device missing/ defective/ showing evidence of disturbance
Any interrupter device fitted to the vehicle in contravention of the requirements
-
-
D
I
5. When considering prohibition action for non compliance within 10kph of the restricted speed, Examiners must consider the response speeds accepted at annual test - Table A refers. When a check is completed using the TVI programmer/simulator, the annual test fail standard must be met prior to prohibition action being taken (pre-digital tachographs excluding mechanical tachographs).
April 08 VOSA 68
Part 1: Public Service, Heavy Goods IM33 and Agricultural Vehicles Speed Limiters
Table A This applies to all vehicles required to be fitted with a speed limiter:
Passenger Vehicles with more than 8 Passenger Seats (Bus)
1 Vehicle Size (Gross Design Weight)
C&U reg 36A paragraph
First registered Use Diesel / LPG / Natural Gas date Stabilised speed not to exceed
Summary Petrol date Stabilised speed not to exceed
Annual test response speed at which vehicle
will be failed not exceeding 5000
2B & 7 1 January 2005 and after
All existing requirement 100 kph existing requirement 100 kph 102 kph or more
2C & 7 1 October 2001 to 31 December 2004
(Euro III or later engine)
All existing requirement 100 kph
As of 1st
Not Required 102 kph or more (diesel/LPG/CNG only)
5001 to 7500 2A & 7 1 January 2005 and after
All existing requirement 100 kph January 2008, all vehicles with
existing requirement 100 kph 102 kph or more
2C & 7 1 October 2001 to 31 December 2004
(Euro III or later engine)
All existing requirement 100 kph diesel/LPG or natural gas
engines require
Not Required 102 kph or more (diesel/LPG/NG only)
7501 to 10000 2 & 7 1 January 2005 and after
All existing requirement 100 kph a speed limiter set at 100kph or
existing requirement 100 kph 102 kph or more
2 & 7 1 October 2001 to 31 December 2004
All existing requirement 100 kph not to exceed 100kph
existing requirement 100 kph 102 kph or more
2 & 7A 1 January 1988 to 30 September 2001
All existing requirement 100 kph depending on existing requirement set speed of 100 kph
107 kph or more
10001 > 2 & 7 1 January 2005 and after
All existing requirement 100 kph age.
existing requirement 100 kph 102 kph or more
2 & 7A 1 January 1988 to 31 December 2004
All existing requirement 100 kph existing requirement set speed of 100 kph
107 kph or more
Passenger Vehicles with more than 16 Passenger Seats (Coach) Vehicle Size (Gross Design Weight)
C&U reg 36A paragraph
First registered Use Diesel / LPG / Natural Gas date Stabilised speed not to exceed
Summary Petrol date Stabilised speed not to exceed
Annual test response speed at which vehicle
will be failed 7501 > 1 & 6 1 April 1974 to
31 December 1987 All existing requirement speed set
at 112 kph All require speed
limiter set at 112kph.
existing requirement speed set at 112 kph
118 kph or more
Categorisation of Defects April 08 69
Part 1: Public Service, Heavy GoodsIM 33 Speed Limiters, Table A and Agricultural Vehicles This applies to all vehicles required to be fitted with a speed limiter:
Goods
1 Vehicle Size (Gross Design Weight)
C&U reg 36B paragraph
First registered Use Diesel / LPG / Natural Gas date Stabilised speed not to exceed
Summary Petrol date Stabilised speed not to exceed
Annual test response speed at which vehicle
will be failed
3501 to 7500 1A & 9 1 January 2005 and after
All existing requirement 90 kph As of 1st January 2008, all
existing requirement 90 kph 92 kph or more
vehicles with 1B & 9 1 October 2001 to 31 All existing requirement 90 kph diesel/LPG or not required 92 kph or more
December 2004 natural gas (diesel/LPG/CNG only) (Euro III or later engine) engines require
7501 to 12000 1A & 9 1 January 2005 All existing requirement 90 kph a speed limiter existing requirement 90 kph 92 kph or more and after set at 90kph or
not to exceed 1B & 8 1 October 2001 to
31 December 2004 (Euro III or later engine)
All existing requirement 90 kph 90kph depending on
existing requirement 90 kph 92 kph or more
age. 1 & 8 1 Aug 1992 to All existing requirement 96.5 kph EXCEPT 7501 existing requirement 96.5 kph 102 kph or more
30 September 2001 12000kg 12001 > 2 & 9 1 January 2005 and All existing requirement 90 kph vehicles existing requirement 90 kph 92 kph or more
after registered between 1st Aug
2 & 9 1 October 2001 to 31 December 2004
All existing requirement 90 kph 1992 and 30th September 2001
existing requirement 90 kph 92 kph or more
2 & 9 1 January 1988 to All existing requirement 90 kph which are set to existing requirement 90 kph 92 kph or more 30 September 2001 96.5kph.
April 08 VOSA 70
Part 1: Public Service, Heavy Goods IM 34 and Agricultural Vehicles Pressure/ Vacuum Warning and Build Up
1
Description of Defect Severity of Defect Action Notes
Air/ Vacuum Build Up
Air/ Vacuum build up slow
Hydraulic Build Up
Hydraulic pressure build up slow
If the warning device fails to cease operating or gauge does not reach 3.1kg/ sq cm (45psi/ 3bar/ 310kPa) within 9 minutes for vehicle/ trailer/ semi trailer combinations (6 minutes for rigid vehicles and uncoupled tractor units) or 25cm to 30cm vacuum in 2 minutes (See Notes 1, 2 and 3)
If the warning device fails to cease operating or gauge does not reach 3.1kg/ sq cm (45psi/ 3bar/ 310kPa) within 6 minutes for vehicle/ trailer/ semi trailer combinations (3 minutes for rigid vehicles and uncoupled tractor units) or 25cm to 30cm vacuum in 1 minute (See Notes 1, 2 and 3)
If warning device fails to cease operating within 6 minutes (See Note 4)
If warning device fails to cease operating within 4 minutes (See Note 4)
I
D
I
D
1. If the pressure gauge has no warning mark, take the 3.1kg/ sq cm (45 psi/ 3bar/ 310kPa) mark as the warning mark.
2. If the vacuum gauge has no warning mark, take the 25 to 30cm Hg mark as the warning mark.
3. These times are examples only and might vary with vehicle type.
4. These defects apply only to continuous flow hydraulic braking systems.
Categorisation of Defects April 08 71
IM 34 Part 1: Public Service, Heavy GoodsPressure/ Vacuum Warning and Build Up and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Air/ Vacuum Assistance
Insufficient reserve of air/ vacuum
Warning Systems
Warning gauge/ flag/ light/ missing/ not functioning/ not visible
Warning gauge not illuminated
Warning buzzer inoperative
Insufficient pressure or vacuum to give assistance for two or more applications of the brakes after the warning device has operated (See Notes 1 and 2)
Where only one such device is fitted (See Notes 6 and 7)
Otherwise than above
Function not readily visible during the hours of darkness (See Notes 6 and 7)
(See Notes 5, 6 and 7)
I
I
IN
IN
IN
5. Applies (with the exception of the gauge which is not normally fitted) to continuous flow hydraulic braking systems.
6. This inspection applies to all vehicles, except those with an unladen weight of less than 3050kg where the vacuum reservoir is coupled direct to the engine induction manifold. These vehicles do not require a pressure/ vacuum warning device. Certain type approved vehicles (e.g Mercedes Benz 515, 609, 612, 614 and 709, Iveco Daily) have been manufactured without a warning device. The absence of such a device in these cases is not a defect.
7. Vehicles used from 1 April 1983 can be fitted with either a visual warning device or an audible warning device. If both are fitted only one need work. Vehicles first used before 1 April 1983 must be fitted with a visual warning device. If an audible warning device is also fitted this is considered to be an addition to the mandatory requirement.
April 08 VOSA 72
Part 1: Public Service, Heavy Goods IM 36 and Agricultural Vehicles Hand Lever Operating Mechanical Brakes
1
Description of Defect Severity of Defect Action Notes
Controls
Hand brake lever fractured/ incomplete/ seized/ insecure
Fails to fulfil its function
Failure imminent
I
I
1. This means that, when the brake is fully applied, there is not sufficient further movement of the lever because it is at the end of its working travel on the ratchet.
Hand brake lever travel impeded/ cannot be readily operated
Otherwise than above
Cannot be operated satisfactorily
Otherwise than above
D
I
D
2. A locking device might not be obvious from a visual examination.
Excessive side play in hand brake lever Failure imminent or could inadvertently disengage
I
Otherwise than above IN
Insufficient reserve travel on hand brake lever (See Note 1)
Brake efficiency impaired
Otherwise than above
I
D
Hand brake lever pawl and/ or ratchet worn
Lever cannot be set or could inadvertently disengage
I
Otherwise than above IN
Any retaining/ locking device missing/ insecure or detached (specify component)
Retaining device missing or detached.
Retaining device insecure or locking device missing or insecure (See Note 2)
I
D
Categorisation of Defects April 08 73
IM 37 Part 1: Public Service, Heavy GoodsService Brake Pedal and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Controls
Foot brake pedal fractured/ incomplete/ insecure/ pivot excessively worn
Foot brake pedal travel impeded/ cannot be readily operated
Insufficient reserve travel on foot brake pedal (See Note 1)
Foot brake pedal antislip provision missing/ loose/ deteriorated / worn smooth (See Note 2)
Fails to fulfil its function
Failure imminent
Otherwise than above
Cannot be operated satisfactorily
Otherwise than above
Brake efficiency impaired
Otherwise than above
Pad about to become detached or level of grip offered affected
Otherwise than above
I
I
D
I
D
I
D
D
IN
1. Not applicable to power operated braking systems provided the footvalve is fully open before the pedal is fully depressed.
2. The provision of a pedal rubber which is itself of an anti-slip material is not to be regarded as defective if its design pattern is worn smooth.
April 08 VOSA 74
Part 1: Public Service, Heavy Goods IM 38 and Agricultural Vehicles Service Brake Operation
1
Description of Defect Severity of Defect Action Notes
Controls
Foot brake pedal "spongy" indicating a fault in the brake system (See Note 1)
Brake efficiency impaired I
1. These defects might not apply to vehicles equipped with full air/ vacuum or continuous flow hydraulic braking systems.
2. Regulations only require that an anti-
Foot brake pedal "creeps" to floor (See Note 1)
Air/ vacuum assistance not working
Otherwise than above
-
Braking efficiency impaired
D
I
I
lock warning light is fitted, it may be fitted on the drawing vehicle in the case of a semi-trailer.
3. The anti-lock light operating sequences are complex. If Examiners are in doubt about the existence of a defect
Motor Vehicle EBS/ABS Systems
Anti-lock or EBS warning light
Otherwise than above
See Note 2
D
D
and the sequence plate is missing, then providing the warning light is operating, the issue of an Inspection Notice is the appropriate course of action.
4. All ABS and EBS equipped vehicles inoperative or indicates the existence of a fault
and trailers approved to UN or EU requirements must display a warning light to indicate to the driver the existence of a fault in the system. This light is required to illuminate when the system is energised and will extinguish on satisfactory completion of the static test. Some illuminate very briefly and may be missed, particularly in bright lighting conditions. It may be necessary to wait as much as 30 seconds before re-testing to allow the system to re-set.
Categorisation of Defects April 08 75
IM 38 Part 1: Public Service, Heavy GoodsService Brake Operation and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
Trailer Electronic Braking Systems 5. An EBS pictogram from the system (EBS) (See Notes 2, 3, 4 and 5) manufacture or the presence of a
seven pin ISO7638 plug on the trailer Trailer EBS warning light not working or No available evidence of EBS function (See I 'headboard' are reliable indicators that indicates the existence of a fault Notes 4) EBS is fitted.
6. A five pin ISO7638 plug on the headboard is reliable evidence that a trailer is not EBS equipped.
Trailer Anti-lock Braking Systems (ABS) (See Notes 2, 3, 4 and 6) 7. If it can be determined that the trailer
is not equipped with load sensing in Anti-lock brake warning light sequence - D addition to ABS then immediate inoperative or indicates a fault (See Note 7) prohibition action may be appropriate.
Leaks
Indication of leakage in full air/ vacuum/ Leakage such that pressure or vacuum I continuous flow hydraulic brake systems cannot be sustained with engine running just
above idling speed
Otherwise than above D
76 April 08 VOSA
IM 39 Part 1: Public Service, Heavy GoodsHand Operated Brake Control Valve and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
Controls
Brake hand valve fractured/ If not functional I damaged/ insecure/ lever loose
Otherwise than above D
Brake hand control valve cannot be - I moved over its original full travel or cannot be retained in the on or off positions
Parking brake hand valve lever cannot - I be set
Indication of leakage in full Leakage such that pressure or vacuum I air/ vacuum/ continuous flow hydraulic cannot be sustained with engine running brake systems just above idling speed
Otherwise than above D
April 08 VOSA 78
Part 1: Public Service, Heavy Goods IM 41 and Agricultural Vehicles Condition of Chassis
1
Description of Defect Severity of Defect Action Notes
Chassis and Attachments
Chassis main member/ cross member/ outrigger severely corroded/ seriously deformed/fractured/ insecure/ missing/ welding breaking away
Integral bodied vehicle panels forming part of the overall strength of the vehicle of unsuitable type with inappropriate fixings/ insecure
Likely to affect control of the vehicle, safe carriage of load or detachment of component imminent (See Notes 1 and 2)
Otherwise than above
Likely to affect control of the vehicle, safe carriage of load or detachment of component imminent
Otherwise than above
I
IN
I
IN
1. For components normally fixed to the chassis eg fuel tanks, brake reservoirs etc, see other sections.
2. This item includes the condition of any flitch plates that are fitted.
Categorisation of Defects April 08 79
IM 42 Part 1: Public Service, Heavy GoodsElectrical Wiring and Equipment and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes Battery Condition
Battery insecure Likely to fall from vehicle or displacement I 1. PSVs only.
constitutes a fire risk 2. Action to be taken if lights don’t work
Battery leaking
Battery container not vented
Battery cell closure insecure/ missing
Switchgear and Wiring
Wiring insecure/ inadequately insulated/ insulation is or will become ineffective due to chafing or heat.
Lighting switch insecure/ malfunctioning
Otherwise than above
Electrolyte entering passenger compartment of a PSV or likely to cause failure of items which could affect vehicle safety
Otherwise than above
(See Note 1)
Electrolyte entering passenger compartment or likely to cause failure of items which could affect vehicle safety
Fumes entering passenger compartment
Otherwise than above
Constitutes a fire risk
Otherwise than above
If lights work (See Note 2)
IN
I
IN
D
I
I
IN
I
IN
IN
properly is shown in IMs 63 and 66.
April 08 VOSA 80
Part 1: Public Service, Heavy Goods IM 43 and Agricultural Vehicles Engine and Transmission
Description of Defect Severity of Defect Action Notes
Engine/ Transmission Security
Engine or transmission mounting/ subframe fractured/ deteriorated/ insecure
Engine/ transmission detachment imminent
No longer capable of performing its function of location and support
Otherwise than above
I
D
IN
Categorisation of Defects April 08 81
1
IM 44 Part 1: Public Service, Heavy GoodsOil and Waste Leaks and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Oil Leaks
Oil leaking onto road surface (specify location on vehicle)
PSVs Only: Oil or waste contaminating ... (specify component/ material) (See Note 2)
Continuous flow
Dripping giving rise to a patch in excess of 75mm diameter in 5 minutes (See Note 1)
Otherwise than above
Constitutes a health/ fire risk
Otherwise than above
I
D
IN
I
IN
1. When considering several leaks, due regard must be given to the cumulative effect, which could justify prohibition action.
2. "Waste" includes effluent from toilets and other ancillary devices, but does not include water from sinks or hand wash basins.
April 08 VOSA 82
Part 1: Public Service, Heavy Goods IM 45 and Agricultural Vehicles Fuel Tanks and Systems
1
Description of Defect Severity of Defect Action Notes
Fuel Tanks and Systems
Fuel tank and/ or mountings insecure
Fuel tank filler cap and/ or sealing arrangement missing/ defective
Fuel leakage from ... (specify source)
Fuel pipe damaged/ chafed/ insecure
Detachment imminent
Significantly insecure
Otherwise than above
Such as to permit fuel spillage and cause a hazard to the vehicle and/ or other road users (See Note 1)
Otherwise than above
Continuous fuel leak or a leak constituting a hazard to other road users or PSV passengers
Dripping giving rise to a patch in excess of 75mm diameter in 5 minutes (See Note 2)
Otherwise than above
Likely to fracture or leak
Otherwise than above
I
D
IN
I
IN
I
D
IN
D
IN
1. Fabricated and "Emergency" caps are acceptable provided they function effectively. Use of rags etc. in place of a fuel cap must be regarded as a defect.
2. When considering several leaks, due regard must be given to the cumulative effect, which could justify prohibition action.
Categorisation of Defects April 08 83
IM 46 Part 1: Public Service, Heavy GoodsExhaust Systems and PSV Waste Systems and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
Exhaust System (See Note 2) 1. When considering a fire hazard, the nature of the load carried could make
Exhaust system Fumes likely to enter vehicle interior, I more lenient action appropriate. incomplete/ insecure/ leaking detachment imminent or likely to create a
fire hazard (See Note 1) 2. The term "exhaust system" in this context includes the exhaust
Significant deterioration D arrangements of combustion heaters, particulate traps and catalysts.
Leak from exhaust system likely to Brake or fuel pipe likely to fail I cause damage to brake or fuel lines
Exhaust silencer holed or missing Does not reduce as far as is reasonable the D noise level
Exhaust system contaminated by grease Constitutes a fire risk or shield likely to I or oil etc. PSV grease shields detach inadequate/ missing/ insecure
Otherwise than above IN
PSV toilet waste outlet depositing waste - D onto road
April 08 VOSA 84
Part 1: Public Service, Heavy Goods IM 48 and Agricultural Vehicles Suspension
1
Description of Defect Severity of Defect Action Notes
Suspension Location NOTE: AGRICULTURAL VEHICLES
A suspension anchor bracket insecure/ fractured or otherwise defective
Detachment or failure imminent I • DRIVEN AT NOT MORE THAN 20 MPH, AND
Fractured or relative movement between bracket and chassis
D • WEIGHING NO MORE THAN
4070KG UNLADEN WEIGHT Any one nut, bolt or rivet missing/ insecure IN (See Note 1) ARE NOT REQUIRED TO HAVE A
SUSPENSION SYSTEM. A suspension shackle bracket Detachment or failure imminent I insecure/ fractured or otherwise 1. When some tyres of suspension defective Slight movement between bracket and IN attachment bracket are fitted, there
chassis or any one nut, bolt or rivet could be more holes in the bracket missing/ insecure (See Note 1) than holes in the chassis. This would
not be a reason for action. Suspension holding down bolts/ nuts Axle moving relative to suspension unit I insecure/ missing. Saddle fractured (See Note 3) 2. When rubber suspension retainers
are fitted and/ or bonded composite Otherwise than above D bushes and/ or mountings, these
must be in such a condition as to Sub-frame insecure to chassis or body, Detachment or failure imminent I adequately locate the suspension fractured or otherwise defective unit.
Otherwise than above D 3. Examiners will need to take into
A suspension anchor/ shackle pin - I account the method of axle location missing/ sheared (See Note 4) and whether the movement affects
the directional control of the vehicle. A suspension anchor/ shackle pin and or Diametric clearance in excess of one third I bush excessively worn (See Notes 4 diameter of pin 4. Also applicable to the pins and and 4a) bushes locating independent
Clearly worn in excess of the annual test D suspension arms/ balance beam and standard linkage pivots.
Otherwise than above IN Categorisation of Defects April 08 85
IM 48 Part 1: Public Service, Heavy GoodsSuspension and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
A suspension retaining rubber missing/ deteriorated (See Note 2)
A suspension anchor/ shackle pin insecure in its bracket (See Note 4)
A suspension anchor/ shackle pin locking device missing/ ineffective/ insecurely fitted (See Note 4)
A suspension slipper bracket excessively worn/ fractured/ not securely fixed or rebound pin missing
Suspension unit detachment imminent
Excessive relative movement between suspension unit and bracket
Pin displaced
Significantly insecure
Otherwise than above
Missing or ineffective
Insecurely fitted
Spring displaced from slipper bracket
Otherwise than above (See Note 5)
I
D
I
D
IN
I
D
I
D
4a. The maximum permissible wear in a pin and/ or bush is 2mm for a 12mm diameter pin and 1/ 8th of the diameter for larger assemblies. If the degree of wear cannot be confirmed by measurement, advisory action on an Inspection Notice will be appropriate.
5. Delayed action only where a slipper is worn to the extent that it could, at the time of the inspection, clearly affect the movement or correct location of the road spring or has allowed the spring leaf to damage the chassis.
Radius arm or linkage bracket insecure or otherwise defective
Radius arm or linkage bracket fractured/ displaced/ distorted
Detachment or failure imminent
Otherwise than above
Fracture, displacement or distortion adversely affecting directional control
Otherwise than above
I
D
I
D
April 08 VOSA 86
Part 1: Public Service, Heavy Goods IM 48 and Agricultural Vehicles Suspension
1
Description of Defect Severity of Defect Action Notes
Suspension Units and Location
A suspension unit weak/ insecure Bodywork fouling (or likely to foul road wheels if vehicle were laden) or seriously affecting the vehicle’s stability/ control or detachment imminent
I
Otherwise than above IN
A suspension unit incorrectly fitted Directional or braking control affected or likely to be affected
I
Otherwise than above IN
A suspension component displaced/ insecure
Control of vehicle affected, likely to be affected, failure of the suspension imminent or component likely to become detached
I
Otherwise than above IN
Leaf Suspension
Spring leaf fractured/ defective Main leaf fractured or more than half of the intermediate leaves broken
I
Insecure spring leaf, likely to fall away from vehicle
I
Otherwise than as above D
Spring clips loose/ missing/ broken - IN
Spring centre bolt broken/ missing - I
Categorisation of Defects April 08 87
IM 48 Part 1: Public Service, Heavy GoodsSuspension and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes Coil Suspension Coil Spring fractured
Torsion Bar Suspension Torsion bar fractured/ distorted
Bonded Suspension Bonded suspension unit failed/ deteriorated (See Note 6)
Air or Fluid Suspension Suspension unit leaking or deflated. (Specify Component)
Air/ fluid suspension unit or fluid accumulator fouling or otherwise defective (See Note 6b)
Levelling valve inoperative/ excessively worn/ damaged / missing/ leaking
Suspension piping insecure/ chafing/ corroded/ excessively damaged
Air suspension pedestal excessively corroded/damaged distorted or incomplete
Detachment imminent/ safe control of vehicle likely to be affected
Otherwise than above
Fractured, displacement or distortion adversely affecting directional control
Otherwise than above
Failed or seriously deteriorated
Otherwise than as above
Adversely affecting system or vehicle control
Otherwise than above
Damage obvious and failure imminent
Otherwise than as above
Adversely affecting vehicle stability/ control
Otherwise than above
Damage obvious and failure imminent
Otherwise than above
Failure imminent
Otherwise than above
I
D
I
D
I
IN
I
D
I
IN
I
D
I
IN
I
D
6. The term "Bonded Suspension" does not include bump stops.
6a. Some manufacturers of HGVs with air suspension have elected to fit heavy duty shock absorbers which also fulfil the purpose of check straps. Some of these vehicles will have the brackets and mounting points for check straps. Action only if there is evidence of check straps having been fitted and are missing.
6b. Superficial damage should be ignored. ‘Damage’ means the cord structure is damaged.
April 08 VOSA 88
Part 1: Public Service, Heavy Goods IM 48 and Agricultural Vehicles Suspension
1
Description of Defect Severity of Defect Action Notes
Air or Fluid Suspension (continued) 7. Action here only if the stability of the vehicle is adversely affected.
Check strap defective Missing or failure likely (See Note 6a) D 8. The significance of defective shock
Otherwise than above IN absorbers will vary according to the suspension type. Prohibition action
Anti-roll Bars will be appropriate only when it is clear that the handling of the vehicle
An anti-roll bar, pivot, linkage or Missing, detachment imminent or likely to I will be severely affected. e.g. in the mounting missing/ insecure/ fractured/ affect steering case of multi-leaf steel springs the malfunctioning effect of a missing stock absorber will
Otherwise than above IN be less significant than with other road spring types.
An anti-roll bar missing If fitted as standard (See Note 7) I 9. Only where originally required/ fitted.
Shock Absorbers
Missing shock absorber, pivot, linkage or Missing, detachment imminent or likely to I mounting insecure/ fractured/ affect steering (See Note 9) malfunctioning (See Note 8)
Otherwise than above D
Shock absorber leaking - IN
Categorisation of Defects April 08 89
IM 53 Part 1: Public Service, Heavy GoodsAxles, Stub Axles and Wheel Bearings and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
Stub Axles and Wheel Bearings 1. As a general guide, the lift in a stub (See Note 2) axle would normally be considered
excessive if greater than 1.6mm. Excessive wear of king pins and/ or Likely to affect steering or fail prematurely I bushes or swivel joints 2. During roadside checks, it is not
Otherwise than above IN normally possible to raise the wheels of a vehicle off the ground.
Excessive free play in wheel bearings Likely to collapse I
Play in excess of vehicle manufacturer’s IN recommendations
Excessive lift in stub axle or at swivel Evidence of collapse of bearings or loss of I joint shims
Otherwise than above (See Note 1) D
King pin loose in axle beam or swivel Pin displaced or displacement likely I joint excessively worn or insecure
Otherwise than above D
King pin or swivel joint retaining device Retaining device missing or detached I missing/ insecure
Retaining device insecure D
Axle or stub axle cracked - I
April 08 VOSA 90
Part 1: Public Service, Heavy Goods IM 54 and Agricultural Vehicles Steering Mechanism
1
Description of Defect Severity of Defect Action Notes
Steering Box/ Rack 1. During roadside checks, it is not normally possible to raise the wheels
Steering stiff or rough in operation Restricting operation I off the ground. (See Note 1)
Obvious roughness D 2. This item applies only to vehicles fitted with gaiters as original
Steering box noisy/ knocking - IN equipment.
Steering box sector shaft cracked or Shaft cracked or visibly twisted I twisted
Excessive lift/ end float/ wear on sector - D shaft, bushes or splines
Excessive wear in steering rack - D
Steering gear housing Any restriction/ failure or detachment I fractured/ insecure/ damaged imminent
Otherwise than above D
Rack gaiter split/ damaged/ displaced or - D missing (See Note 2)
Categorisation of Defects April 08 91
IM 54 Part 1: Public Service, Heavy GoodsSteering Mechanism and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
Steering Linkage
Steering drop arm insecure If movement is such that failure is likely
Excessive abnormal movement
I
D
3. Some steering joints are spring loaded. The designed amount of movement must not be confused with abnormal movement.
Steering ball pin insecure Any insecurity I
Steering ball pin grooved Diameter substantially reduced I
Otherwise than above IN
Track rod/ drag link insecure Excessive movement between mating parts I
Slight movement D
Excessive movement in steering joint (See Note 3)
If joint in danger of separation
Excessive abnormal movement
I
D
Otherwise than above IN
Steering relay arm pivot excessively worn
Failure imminent
Otherwise than above
I
D
Steering linkage misaligned Steering function impaired I
Otherwise than above IN
April 08 VOSA 92
Part 1: Public Service, Heavy Goods IM 54 and Agricultural Vehicles Steering Mechanism
Description of Defect Severity of Defect Action Notes
Steering Linkage
Steering relay arm pivot housing/ bracket fractured/ insecure
Steering arm insecure
Steering component fractured/ deformed or otherwise defective (Specify component)
Steering component fouling, or road wheels/ tyres restricted in travel (Specify component)
Steering retaining/ locking device missing / insecure
Lock stop or other steering component missing/ insecure
Power Steering
Pump insecure or it’s drive system missing or defective
Failure or detachment imminent
Otherwise than above
Detachment imminent
Otherwise than above
Failure imminent
Otherwise than above
Steering function impaired
Otherwise than above
Retaining device missing or ineffective
Retaining device insecure or any locking device missing or insecure
Likely to become detached
Otherwise than above
Failure or detachment imminent
Otherwise than above
I
D
I
D
I
D
I
D
I
D
I
IN
I
D
Categorisation of Defects April 08 93
1
IM 54 Part 1: Public Service, Heavy GoodsSteering Mechanism and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Power Steering (See Note 4)
Power steering malfunctioning/ inoperative or otherwise defective
Power steering ram, anchor bracket or pump mounting fractured/ insecure or otherwise defective.
Power steering ram fluid pipes damaged
Power steering pipes fouling (Specify component being fouled)
Excessive fluid/ air leakage from power steering (specify component)
Power steering ram joint excessively worn/ spring weak/ spring broken
Disconnected, inoperative or failure imminent (See Note 5)
Otherwise than above
Failure or detachment imminent
Otherwise than above
If steering function impaired
Otherwise than above
Pipes damaged and likely to fail
Otherwise than above
Fluid/ air leaking continuously, failure of power steering imminent
Contamination of materials so as to constitute a risk of fire
Fluid leakage in excess of 75mm diameter patch in 5 minutes
Otherwise than above
If joint in danger of separation, or detachment of ram imminent
Otherwise than above
I
D
I
D
I
IN
I
IN
I
I
D
IN
I
D
4. Power steering components must be checked with the engine running. Inspection will include power steering drive mechanisms.
5. If power steering equipment is optional and has been removed with no adverse effect on the steering, no action must be taken.
April 08 VOSA 94
Part 1: Public Service, Heavy Goods IM 57 and Agricultural Vehicles Transmission
1
Description of Defect Severity of Defect Action Notes
Propeller Shafts & Drive Shafts
Propeller shaft damaged
Universal joint excessively worn/ flange cracked or insecure on the propeller shaft (See Note 1)
Propeller shaft flange bolts loose/ missing
Propeller shaft carrier bearing badly worn/ damaged/ mounting loose
Front Wheel Drive Shafts
CV joint and or shaft coupling excessively worn. CV gaiter split, missing or insecure
Bent, fouling or fractured and failure imminent
Other significant damage
Otherwise than above
Failure or detachment likely
Significantly defective
Otherwise than above
Shaft likely to become detached
Other significant insecurity
Otherwise than above
Failed or failure imminent
Other significant defect
Otherwise than above
Bearings collapsed or excessively worn,splines excessively worn or coupling/ jointseriously deteriorated and failure imminent
Significantly deteriorated component
Otherwise than above
I
D
IN
I
D
IN
I
D
IN
I
D
IN
I
D
IN
1. Prohibition action for excessive wear of universal joint is only justified when radial movement indicates that needle roller bearings are missing from one or more cups.
Categorisation of Defects April 08 95
IM 58 Additional Braking Devices Part 1: Public Service, Heavy Goods(including Retarders) and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
Additional Braking Devices 1. Where legally required to be fitted (including Retarders) (refer to vehicle technical record).
Device not working/ missing (See Note 1) - D
Otherwise than above IN
Retarder insecure Likely to become detached I
Heat shield missing/ defective where - D required
Retarder contaminated with oil/ with Constitutes a fire hazard I inadequate clearance from other components
Oil leakage from retarder Continuous leak I
Leakage in excess of 75mm diameter patch D in 5 minutes
Otherwise than above IN
Retarder wiring chafed/ insecure Fire hazard I
Otherwise than above IN
April 08 VOSA 96
Part 1: Public Service, Heavy Goods IM 59 and Agricultural Vehicles Brake Systems and Components
1
Description of Defect Severity of Defect Action Notes
Mechanical Components 1. A locking device: • Might not be obvious from a visual
Any brake component excessively Failed or likely to fail I examination worn/ corroded/ fractured/ reduced in • Might not be mandatory. diameter/ number of strands reduced (Specify Serious reduction of strength/ excessively worn or D component) displaced 2. Automatic slack adjusters must be
fitted to HGV and PSV motor vehicles Otherwise than above IN first used from 1 April 1995 and trailers
manufactured from 1 April 1995. Any retaining/ locking device missing/ insecure Retaining device missing or detached I (Specify component) 3. As a guide when automatic slack
Retaining device insecure or locking device D adjusters are fitted the total travel missing or insecure (See Note 1) should not exceed 2/3rd of the total
actuator travel. Movement obviously Brake backplate/dust cover loose Brake efficiency impaired or detachment imminent I in excess of this, particularly if unequal
Otherwise than above IN across an axle, can be taken as evidence that the adjuster is
Abnormal movement of levers indicating Brake efficiency impaired I inoperative. This guidance does not maladjustment (See Notes 3 and 4) apply to arrangements, particularly
Otherwise than above D disc brakes, where the adjustment Automatic brake slack adjuster and/ or Brake efficiency impaired I may take place within the caliper or component missing/disconnected/ insecure or elsewhere and 'Automatic Slack inoperative (See notes 2, 3, 4 and 5) Otherwise than above D Adjusters' are not fitted.
Actuator/Brake Cylinder Travel 4. All automatic slack adjusters must Excess or restricted travel of brake actuator or Brake efficiency impaired (see Note 6) I return fully on release of the brakes. If cylinder they do not, they will not be sensing
Excess amount of travel (see Note 7) D the correct state of adjustment and therefore be incapable as operating as
Otherwise than above IN intended. Brake Actuators Air/vacuum actuator missing/ insecure/ Missing/ Inoperative or about to fail I damaged/ fractured/excessively corroded/ incorrectly fitted Otherwise than above D
Categorisation of Defects April 08 97
IM 59 Part 1: Public Service, Heavy GoodsBrake Systems and Components and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Loss of air/vacuum
Brake Travel Indicators
Brake piston/diaphragm travel indicator missing/inoperative
Brake adjustment indicator shows that brake adjustment is necessary
Servos
Brake servo insecure
Brake servo damaged/incorrectly fitted/ fractured/excessively corroded
Excessive travel of brake servo
Servo losing vacuum
Pressure/vacuum cannot be sustained with the engine running just above idling speed and brakes applied
Otherwise than above
(See Note 8)
Brake efficiency impaired (See Note 9)
Otherwise than above
Detached or detachment imminent
Otherwise than above
Failed or failure imminent
Otherwise than above
Brake efficiency impaired
Otherwise than above (See Note 8)
Vacuum cannot be sustained with engine running above idling speed and brakes applied
Otherwise than above
I
D
IN
I
IN
I
D
I
D
I
IN
I
D
5. Particular attention should be paid to the control arm and anchor bracket if so equipped. These will fracture and/or detach if not correctly fitted.
6. When immediate action is taken this must be reinforced with evidence that the efficiency is impaired, eg. brake test results or, in the case of adjustment, clearly no reserve travel.
7. Excess travel means when there is too little reserve travel left in the actuator which clearly demonstrates that the point at which adjustment was necessary has been exceeded.
8. Brake actuators or servos in which the travel cannot be visually assessed are often fitted with a device that indicates the extent of travel of the piston or diaphragm.
April 08 VOSA 98
Part 1: Public Service, Heavy Goods IM 59 and Agricultural Vehicles Brake Systems and Components
1
Description of Defect Severity of Defect Action Notes
Brake Discs and Drums Brake disc missing/ loose/ fractured/ excessively worn/ friction surface excessively corroded/ pitted (See Note 10)
Brake drum fractured/ missing/ excessively worn (See Note 10)
Brake friction lining/ pad missing/ excessively worn/ insecure/ friction pad or lining not contacting drum or disc
Severely contaminated pad/lining material
Brake efficiency impaired (See Note 9)
Failed or failure imminent
A fracture extending through the surface into the ventilation cavity of a disc
Disc friction surface excessively/ deteriorated/ pitted to the extent that the pad is not contacting areas of the surface
Otherwise than above
Missing or failure imminent
Drum fractured through
Otherwise than above
Missing/ detached not contacting and/or braking efficiency impaired
Linings worn to excess (See Note 11)
Otherwise than above
Braking efficiency impaired (See Note 9)
Where contamination is clearly evident and likely to affect performance but brake test equipment is not available to confirm
Otherwise than above
I
I
D
D
IN
I
I
IN
I
D
IN
I
D
IN
9. When immediate action is taken this must be reinforced with evidence that the efficiency is impaired, e.g. brake test results or, in the case of adjustment, clearly no reserve travel.
10. Surface cracks on brake discs and drums are a normal feature that should be ignored.
11. This would normally be a lining less than 1.5mm (1/16") thick at any point.
Categorisation of Defects April 08 99
IM 59 Part 1: Public Service, Heavy GoodsBrake Systems and Components and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
Vehicle Electronic (EBS) or Anti-lock 12. Some Public Service Vehicles are Braking Systems (ABS) manufactured without ABS but may Any component forming part of an anti-lock Such that the ABS system is rendered inoperative D have ABS valves fitted as standard. braking system missing/ damaged/ or the warning light sequence indicates there is If no action is taken under IM 38 disconnected (See Note 12) a fault then the fitment of these
components is not to be considered Trailer Anti-lock Braking Systems (ABS) a defect. (See Note 13) Any component forming part of an anti-lock Such that the ABS system is rendered inoperative D 13. A five pin ISO7638 plug on the braking system missing/damaged/ or the warning light sequence indicates there is a ‘headboard’ is reliable evidence that disconnected (See Notes 16 and 21) fault a trailer is not EBS equipped.
Disconnected or damaged, likely to be affecting D 14. A EBS pictogram from the system the correct function manufacture or the presence of a
seven pin ISO7638 plug on the Otherwise than above IN trailer 'headboard' are reliable
indicators that EBS is fitted. ISO7638 cable missing (See Note 16) - D
15. Acceptable evidence will normally Trailer Electronic Braking Systems (EBS) be the noise made by electro(See Note 14) pneumatic valves as the system Any component forming part of an electronic Such that the EBS system is rendered inoperative I goes through its self-check cycle. braking system missing/ damaged/ or the warning light sequence indicates there is a disconnected fault and no evidence of operation (See Note 15) 16. Vehicles towing trailers, where both
are equipped with ISO7638 Otherwise than above but evidence of operation D connectors, must have these
connected with an appropriate cable ISO7638 cable missing (See Note 16) No evidence of operation (See Note 15) I regardless of any alternative method
available on the vehicle to provide Otherwise than above D power. (This came into effect from 2
Air Compressor Drive May 2002). Drive belt(s) missing/ badly deteriorated/ Air build-up seriously affected or failure imminent I loose
Otherwise than above D
100 April 08 VOSA
Part 1: Public Service, Heavy Goods IM 59 and Agricultural Vehicles Brake Systems and Components
1
Description of Defect Severity of Defect Action Notes
Air/Vacuum Reservoir 17. Minor valves might not be supported. Brake air/ vacuum reservoir damaged/ Detachment or failure imminent I 18. Damp patches around valves are not to be excessively corroded/insecure considered as necessarily indicating a
Otherwise than above D defect. 19. Faults, particularly those concerning the
Brake Valves free movement of valves, are often difficult Brake valve inoperative (specify component) - I to positively detect. If examiners are in
doubt about the existence of a defect the Brake valve insecure (specify component) Detached or detachment imminent and or likely to I IN option must be used. (See Note 17) cause leakage at connections 20. This inspection applies to all types of load
sensing valves. Insecurity due to weakness or failure of supporting D 21. Goods vehicles first used after 1 April 1983 structure require either a Load Sensing Valve (LSV)
or Anti-Lock Braking (ABS) to comply with Brake valve damaged/ fractured/ Fractured or damaged to an extent that renders I EEC Braking Directives. There are excessively corroded (Specify component) the valve inoperative or failure imminent exemptions.
a. Public Works Vehicles, examples are Otherwise than above IN mobile libraries and door to door domestic
refuse collection vehicles. Brake valve leaking Leakage such that pressure or vacuum cannot be I Note:- "Domestic refuse" vehicles used for the
sustained with engine running just above idle collection of industrial waste for which a speed charge is made are not exempt.
b. Vehicles with high unladen weights (where Other significant leak D the ratio between laden and unladen
weight is small) may meet the requirements Otherwise than above IN without a load sensing valve.
c. Trailers with a Gross Vehicle Weight Load sensing valve missing/ seized/ Clearly not able to function as intended (See Note 19) I exceeding 3500kg, manufactured on or bypassed, linkage defective/ disconnected or after 1 October 1982 are required to be out of adjustment (See Notes 19 and 20) Otherwise than above IN fitted with either a Load Sensing Valve
(LSV) or Anti-lock Braking (ABS) or an Excessive oil/ contaminant discharge from (See Note 18) D Electronic Braking System (EBS). brake valves
Categorisation of Defects April 08 101
IM 59 Part 1: Public Service, Heavy GoodsBrake Systems and Components and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Brake Pipes and Hoses
Brake pipe excessively chafed/ damaged
Brake pipe corroded
Brake pipe inadequately clipped/ supported/ repaired
Brake pipe fouling (Specify component fouled)
Brake hose chafed/ deteriorated/ stretched/ bulging/ kinked/ twisted/ fouling/ exposed to excessive heat
Brake pipe/ hose/ coupling/ connection leaking (Specify component)
Failed or failure imminent
Otherwise than above (See Note 22)
Failed or failure imminent
Deeply pitted, weakened
Failed or failure imminent
Significantly insecure
Otherwise than above
Failed or failure imminent
Otherwise than above
Failed or failure imminent
Otherwise than above (See Note 22)
Any positive hydraulic leak
Leakage such that pressure or vacuum cannot be sustained with engine running just above idle speed
Otherwise than above
I
D
I
D
I
D
IN
I
D
I
D
I
I
D
d. Drawbar trailers with a Gross Vehicle Weight exceeding 10000kg and semi trailers with a total axle summation exceeding 10000kg manufactured on or after 1 October 1991 must be fitted with either ABS or EBS.
e. Any trailer with a Gross Vehicle Weight exceeding 3500kg manufactured after 1 January 1968 with an EEC two line or two plus three line trailer braking system, must be fitted with either an LSV, ABS or EBS.
In any of the above cases more than one system may be fitted.
Note: A trailer manufactured after 1 January 1968 and before 1 October 1991 may be exempt the fitment of a Load Sensing Valve where the unladen weight is 60% or greater than the Gross Vehicle Weight.
22. Minor damage that is unlikely to get worse may be ignored.
102 April 08 VOSA
Part 1: Public Service, Heavy Goods IM 59 and Agricultural Vehicles Brake Systems and Components
1
Description of Defect Severity of Defect Action Notes
Hydraulic Systems
Brake master cylinder/ reservoir/ wheel cylinder/ caliper insecure
Brake master cylinder/ wheel cylinder/ caliper damaged/ disconnected/ missing/ incorrectly fitted/ fractured
Brake fluid leaking from (Specify source)
Absence of or low fluid level in hydraulic brake fluid reservoir
Hydraulic Brake Cylinders
A hydraulic cylinder mounting insecure/ cracked/ fractured/ damaged or a stop pin or locking device missing or insecure
A hydraulic cylinder leaking
Detached or detachment imminent
Otherwise than above
Failed or failure imminent
Otherwise than above
Obvious leak leading to brake failure or presenting a risk of fire (See Note 23)
Otherwise than above
Reservoir empty
Fluid level clearly below the minimum level indication
Otherwise than above
Detached or detachment/ failure imminent
Otherwise than above (See Note 24)
Brake pedal creeps to floor or obvious leak (See Note 23)
I
D
I
D
I
IN
I
D
IN
I
D
I
23. Hydraulic brake master and wheel cylinders may show dampness around the vent and dust covers due to the brake fluid acting as a seal lubricant. Care must be taken to ensure that any dampness is not confused with seal failure which would result in a positive leak.
24. "Fully floating" cylinders must not be confused with insecure cylinders.
Categorisation of Defects April 08 103
IM 62 Part 1: Public Service, Heavy GoodsRear Markings and Reflectors and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
Rear Markings 1. No reflectors are required to be fitted to vehicles not fitted with front or rear
Insecure, partially or completely missing, Detachment imminent I position lamps. No side reflectors are incorrectly located or not clearly visible required on buses. from the rear Otherwise than as above IN
2. Side reflectors are required on:-Incorrect rear marking fitted
Obligatory Reflectors (See Note 1)
- IN • Motor vehicles first used before 1
April 1986 and longer than 8 metres overall.
Obligatory reflector missing/ deteriorated/ incorrectly fitted/ obscured/
Detachment imminent
Otherwise than above
I
IN • Motor vehicles first used from 1 April
1986 and longer than 6 metres insecure overall.
HGV side reflector missing, deteriorated or of incorrect colour
(See Notes 2 and 3) IN • Trailers longer than 5 metres overall, excluding any drawbar.
HGV side reflector incorrectly fitted or (See Note 2) IN 3. HGV side reflectors must be amber, not plainly visible from the side unless they are within 1 metre of the
rear of the vehicle, in which case they can be red.
104 April 08 VOSA
Part 1: Public Service, Heavy Goods IM 63 and Agricultural Vehicles Lamps
1
Description of Defect Severity of Defect Action Notes
All lamps 1. No lamps are required to be fitted to vehicles only used on roads between
A lamp or lens insecure or damaged Likely to cause injury or detachment I sunrise and sunset. Trailers imminent manufactured before 1 October 1985
are not required to be fitted with front Otherwise than above IN position lamps while being drawn by a
passenger vehicle. Obligatory Front Position Lamps (See Note 1) 2. When visibility is seriously reduced
(to less than 100 metres), the use of Obligatory front position lamp insecure Lamp so insecure that detachment is I dipped headlamps and side lamps is
imminent required by Regulation.
Otherwise than above IN
Obligatory front position lamp (See Note 2) IN inoperative/ missing/ dim/ obscured/ affected by the operation of another lamp/ lens broken or missing
Obligatory front position lamp has - IN intermittent operation, flickers when tapped or does not face to front.
Categorisation of Defects April 08 105
IM 63 Part 1: Public Service, Heavy GoodsLamps and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Obligatory Headlamps (See Note 3)
Obligatory dipped headlamp inoperative/ missing/ obscured/ dim/ flickers when tapped by hand (See Note 4)
Obligatory headlamp insecure or lens broken or missing
The dipped beam and/ or main beam emitted from a matched pair of obligatory headlamps cannot be switched on or off together
In any grouped obligatory headlamp system (ie. more than one matched pair) they cannot either be dipped in unison or when one matched pair (the outer pair if not vertically in line) is dipped the other pairs are extinguished
Obligatory End-Outline Marker Lamps (See Notes 1, 5 and 6)
Obligatory marker lamp missing/ insecure/ obscured/ inoperative/ incorrectly positioned
When use of headlamps is compulsory
When use of headlamps is not compulsory
Detachment imminent
Otherwise than above
Likely to cause dazzle when headlamp use is compulsory
Otherwise than above
Likely to cause dazzle when headlamp use is compulsory
Otherwise than above
Detachment imminent
Otherwise than above
I
IN
I
IN
I
IN
I
IN
I
IN
3. For agricultural vehicles see paragraph 3 of the introduction.
4. Where the defective headlamp is part of a grouped system, consideration must be given to the capability of other headlamps in that group.
5. End marker lamps are required on vehicles first used on or after 1 April 1991 that have an overall width greater than 2100mm and a maximum speed exceeding 25mph.
106 April 08 VOSA
Part 1: Public Service, Heavy Goods IM 63 and Agricultural Vehicles Lamps
1
Description of Defect Severity of Defect Action Notes
Obligatory Rear Position Lamps (See Note 6)
Obligatory rear lamp insecure Lamp so insecure that detachment is imminent
Otherwise than above
I
IN
6. No lamps are required to be fitted to vehicles only used on roads between sunrise and sunset. Motor vehicles first used before 1 April 1986 are not required to be fitted with any rear lamps while drawing a trailer fitted with lamps.
Obligatory rear lamp inoperative/ missing/ dim/ obscured/ affected by the operation of another lamp/ lens broken or missing
Obligatory rear lamp has intermittent operation, flickers when tapped or does not face the rear, lens broken or missing
Rear Fog Lamps (See Note 6)
Likely to prevent width and presence of the vehicle being indicated adequately during compulsory use (See Note 7)
Otherwise than above
-
I
IN
IN
7. This action is appropriate only between sunset and sunrise or in conditions of seriously reduced visibility.
8. Rear fog lamps are required on vehicles first used on or after 1 April 1980 (or 1 April 1986 in the case of agricultural vehicles or works trucks) with an overall width greater than 1300mm and a maximum speed exceeding 25mph.
Rear fog lamps insecure Detachment imminent
Otherwise than above
I
IN
9. Where one rear fog lamp is fitted, it must be positioned on the centre-line or offside of the vehicle.
Rear fog lamp missing/ obscured/ inoperative/ incorrectly positioned
(See Notes 8 and 9) IN
Rear fog lamp emits light of a colour - IN other than red or comes on with brake light
Categorisation of Defects April 08 107
IM 63 Part 1: Public Service, Heavy GoodsLamps and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
1
Stop Lamps (See Note 10)
Stop lamp inoperative/ obscured/ missing/ dim/ otherwise defective in operation
Stop lamp insecure
Reversing Lamps
Reversing lamp insecure
No stop lamp shows a steady red light when the brake is applied
Stop lamp(s) remain on when all brakes are released (See Note 12)
Otherwise than above (See Note 11)
Detachment imminent
Otherwise than above
Detachment imminent
Otherwise than above
I
I
IN
I
IN
I
IN
10. Stop lamps are not required on vehicles not fitted with front or rear position lamps or to vehicles with a maximum speed not exceeding 25mph or to agricultural vehicles first used before 1 April 1986 or to any other vehicle first used before 1 January 1936.
11. Vehicles first used on or after 1 January 1936 and before 1 January 1971 need only one stop lamp. This lamp must be fitted on the centre-line or offside of the vehicle.
12. On vehicles with an air brake system, care must be taken to ensure the brake lights are not on due to low air pressure.
Reversing lamp indicator inoperative - IN
Rear Registration Plate Lamps
Missing or not in good working order - IN
108 April 08 VOSA
Part 1: Public Service, Heavy Goods IM 66 Direction Indicators and Agricultural Vehicles and Hazard Warning Lamps
1
Description of Defect Severity of Defect Action Notes
Direction Indicators (See Note 1)
Direction indicator insecure
Direction indicator missing/ inoperative/ not functioning correctly/ damaged/ obscured/ lens broken or missing
Indicator warning lamp inoperative/ not fitted
Hazard Warning Lamps
Hazard warning lamp inoperative/ not functioning correctly
Side Repeater Indicators
Side repeater indicator inoperative/ not functioning correctly
Detachment imminent
Otherwise than above
Indicator cannot be used to clearly show the driver’s intention (See Note 2)
Otherwise than above
If the warning lamp is inoperative or not fitted and the driver cannot see that each indicator is functioning and there is no audible tell-tale device
(See Note 3)
(See Note 3)
I
IN
I
IN
IN
IN
IN
1. No direction indicators are required to be fitted to vehicles not fitted with front or rear position lamps.
2. The criteria must be the inability of the driver to signal the intention to change direction by whatever means. If remaining indicator lamps or repeaters fulfil this purpose then Inspection Notice action only will be appropriate. It is unlikely that hand signals will be acceptable for most vehicles covered by this Part of the guide.
3. Vehicles first used before 1 April 1986 are not required to have hazard warning lamps or side repeater indicators.
Categorisation of Defects April 08 109
IM 67 Part 1: Public Service, Heavy GoodsAim of Headlamps and Agricultural Vehicles
1
Description of Defect Severity of Defect Action Notes
Aim of Headlamps (See Note 3)
Headlamp aim too high or too far to the right
Headlamp aim too low or too far to the left
Likely to cause dazzle when use of dipped headlamps is compulsory
Otherwise than above (See Notes 1 and 2)
Likely to prevent the driver from being able to drive safely when use of dipped headlamps is compulsory
Otherwise than above (See Notes 1 and 2)
I
IN
I
IN
1. An immediate prohibition will normally only be appropriate for such a defect in conditions of seriously reduced visibility or at night.
2. If the degree of misalignment of the headlamp aim does not warrant an immediate prohibition, but an instrumented check shows that the headlamp aim falls outside the statutory test limits, an Inspection Notice should be issued.
3. For agricultural vehicles see paragraph 3 of the introduction.
110 April 08 VOSA
Part 1: Public Service, Heavy Goods IM 71 and Agricultural Vehicles Service Brake Performance
1
Description of Defect Severity of Defect Action Notes
Service Brake Operation and BRAKE PERFORMANCE Performance (See Note 5)
1. When testing brakes, examiners Service brake does not operate on every - I should have no difficulty in road wheel where originally designed to establishing the performance of the do so (See Note 6) service brake and, where the
secondary brake is also the parking Service brake efficiency low (See Notes Performance does not meet prescribed I brake, the assessment of their 1, 2 and 4) C&U requirements (specify) performance should create no
problems. A malfunction indicated by abnormally low D effort (specify) in excess of the annual test 2. Particularly when using a roller brake imbalance criteria (See Note 3) tester to determine brake
performance, examiners should, Overall performance below normal IN where possible, take into account the expectation maximum design weight of the vehicle
(or calculated laden weight in the Service brake unbalanced, evidence of Marked deviation from straight path when I case of a PSV). oval brake drum or distorted disc brakes applied (See Note 3) This will usually only be possible if the
Otherwise than above IN vehicle is at or near to maximum weight and the examiner is sure that
Service brake binding excessively Severely overheated and either failure or I all brake modulating valves (eg load (See Note 3) fire likely sensing valves) are delivering
maximum pressure. Otherwise than above IN
In the case of a vehicle at a lower weight, the examiner might only beable to judge brake performanceagainst presented weight where thisis known.
Categorisation of Defects April 08 111
1
IM 71 Part 1: Public Service, Heavy GoodsService Brake Performance and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
3. Where vehicles are tested on a roller brake tester for imbalance/ ovality/bind the appropriate InspectionManual criteria must be used.
4. There is no performance laid down foragricultural motor vehicles driven atnot more than 20mph if first usedbefore 1 June 1986 or agriculturaltrailers manufactured before 1 December 1985. After these dates, they are required to achieve 25% ofthe total designed maximum axleweights.
5. When measuring brake performance,percentage efficiencies and type ofequipment should be recorded.
6. Some vehicles, perhaps the mostcommon being rear steer tractor units,are designed so that the second steerbrakes do not operate until the driveaxle is heavily loaded (e.g. between60% and the maximum permittedweight at which point the axle isdeployed and air is fed to theactuators). These axles will normallybe “supplementary axles” with singlewheels positioned immediately in frontof, or behind drive axles. However, other configurations may beencountered.
112 April 08 VOSA
Part 1: Public Service, Heavy Goods IM 72 and Agricultural Vehicles Secondary Brake Performance
Description of Defect Severity of Defect Action Notes
Secondary Brake Operation and Performance (See Note 2)
Secondary brake efficiency low (See Notes 1, 3 and 4)
Performance does not meet prescribed C&U requirements (specify)
Little or no braking effort at any wheel equipped with a brake operated by the secondary brake system
Overall performance below normal expectation
I
D
IN
BRAKE PERFORMANCE
1. When testing brakes, examiners should have no difficulty in establishing the performance of the service brake and, where the secondary brake is also the parking brake, the assessment of their performance should create no problems.
Where the secondary brake can be represented by each constituent part of a split or dual brake system, the performance can be difficult to ascertain.
In such circumstances, if the parking brake can produce the secondary brake performance, the Regulations can be regarded as satisfied.
Where this is not possible, the examiner can only use discretion, having regard to the general condition of the brakes and the service brake performance.
2. When measuring brake performance,percentage efficiencies and type ofequipment should be recorded.
Categorisation of Defects April 08 113
1
1
IM 72 Part 1: Public Service, Heavy GoodsSecondary Brake Performance and Agricultural Vehicles
Description of Defect Severity of Defect Action Notes
3. Particularly when using a roller brake tester to determine brake performance, examiners must, where possible, take into account the maximum design weight of the vehicle (or calculated laden weight in the case of a PSV).
This will usually only be possible if the vehicle is at or near to maximum weight and the examiner is sure that all brake modulating valves (eg load sensing valves) are delivering maximum pressure.
In the case of a vehicle at a lower weight, the examiner might only be able to judge brake performance against presented weight, where this is known.
4. There is no performance laid down for agricultural motor vehicles driven at not more than 20mph if first used before 1 June 1986 or agricultural trailers manufactured before 1 December 1985. After these dates, they are required to achieve 25% of the total designed maximum axle weights.
114 April 08 VOSA
Part 1: Public Service, Heavy Goods IM 73 and Agricultural Vehicles Parking Brake Performance
1
Description of Defect Severity of Defect Action Notes
Parking Brake Performance (See Note 5)
Parking brake inefficient (See Notes 1, 2, 3 and 4)
Does not meet prescribed C&U requirements (specify)
Little or no braking effort on a roadwheel equipped with a brake operated by the parking brake system
Overall performance below normal expectation
I
D
IN
1. Particularly when using a roller brake tester to determine brake performance, examiners must, where possible, take into account the maximum design weight of the vehicle (or calculated laden weight in the case of a PSV). This will usually only be possible if the vehicle is at or near to maximum weight. In the case of a vehicle at a lower weight, the examiner might only be able to judge brake performance against presented weight, where this is known.
2. For the purpose of this test, the vehicle can be brought to rest prior to applying the parking brake (Gradient and Static Test only).
3. If the minimum efficiency prescribed in C&U is met, but performance is less than would be expected, an Inspection Notice must be issued if action has not been taken under any other heading.
4. There is no specified performance for parking brakes on agricultural vehicles driven at not more than 20 mph and first used before 1 January 1968.
5. When measuring brake performance,percentage efficiencies and type ofequipment should be recorded.
Categorisation of Defects April 08 115
VOSA Categorisation of Defects Contents Part 2: Passenger Cars, Private Buses and Light Goods Vehicles
1. ENGINE AND ASSOCIATED EQUIPMENT
Engine Security.......................1 Oil Leaks.................................1 Fuel Tank and System.............1 Exhaust System......................2 Exhaust Emission.................. 2 Speed Limiter..........................3
2. TRANSMISSION
Drive/ Propeller Shafts.............5
3. RUNNING GEAR Road Wheels and Hubs......... 6
Spare Wheel...........................7
Tyres.......................................7 Axles, Stub Axles and Wheel Bearings.....................10
4. SUSPENSION
Springs...................................12 Anchor/ Shackle Pins.............13
Spring Brackets..................... 14
Torsion Bars...........................14
Bonded Units.........................14
Air Suspension......................15
Suspension Arms/ Linkages/ Sub-frames............................15 Shock Absorbers...................15
Anti-roll Bars......................... 16
Displacers..............................16 General..................................16
5. BRAKES Controls.................................17 Warning Systems..................18 Air/ Vacuum Assistance.........18 Actuators...............................19 Servos...................................20 BrakeTravel/ Adjustment Indicators...............................20 Brake Valves..........................21
Air/ Vacuum Reservoir...........21
Hydraulic Systems.................22
Mechanical Components.......23
ABS Components..................25
Brake Pipes and Hoses........25 Additional Braking Devices/ Retarders/ Exhaust Brakes...27
Service Brake Operation and Performance..........................28
Parking Brake Operation and Performance..........................29
General..................................29
6. STEERING
Steering Wheel and Column..................................30
Steering Box/ Rack & Pinion....................................31
Steering Linkage...................32 Power Steering .....................33
King Pins...............................34
7. CHASSIS
Chassis and Attachments......35
Trailer Coupling.....................35
Coupling on Trailer................37
8. VEHICLE INTERIOR
Driving controls......................38
Driver’s Area and Fittings......38
Passenger Seats...................39
Seat Belts..............................40
9. BODYWORK
Body Panelling......................41 Bumpers............................... 41
Wings and Wheel Arches..... 42
Registration Plates and VIN
Details...................................42
Windscreen and Windows....43
Washers and Wipers............43
Doors..................................44
Bonnet................................44
10. ELECTRICAL EQUIPMENT
Battery.................................45 Switchgear and Wiring.......45
11. LAMPS AND REFLECTORS
Front Position Lamps..........46
Rear Position Lamps...........47 Rear Fog Lamps..................47
Reflectors............................48
Direction Indicators..............48 2 Hazard Warning Lamps.......48
Side Repeater Indicators.....48
Headlamps..........................49
Stop Lamps.........................50
Reversing Lamps................51
Rear Registration Plate Lamps.................................51
Categorisation of Defects
Part 2: Passenger Cars, Private Buses Section 1 and Light Goods Vehicles Engine and Associated Equipment
Description of Defect Severity of Defect Action Notes
Engine Security
Engine mounting fractured, deteriorated or insecure
Oil Leaks
Oil leak from engine/ assemblies
Fuel Tank and System
Fuel tank or other system components insecure
Fuel leakage from (specify source)
Fuel tank filler cap and/ or sealing arrangement missing/ defective
Fuel pipe damaged/ chafed/ insecure
Engine detachment imminent
Otherwise than above
Continuous flow
Dripping giving rise to a patch in excess of 75mm diameter in 5 minutes (See Note 1)
Otherwise than above
Detachment imminent
Significantly insecure
Otherwise than above
Continuous fuel leak or a leak constituting a fire risk or a hazard to other road users
Significant leak (See Note 4)
Otherwise than above
Such as to permit fuel spillage and cause a hazard to the vehicle and/ or other road users (See Notes 2 and 3) Otherwise than above
Likely to fracture or leak
Otherwise than above
I
IN
I
D
IN
I
D
IN
I
D
IN
I
IN
D
IN
1. When considering several leaks, due regard must be given to the cumulative effect which could justify prohibition action.
2. If any fuel leak or spillage is likely to constitute a fire risk, or present a hazard to other road users, an immediate prohibition must be issued.
3. Fabricated and ‘emergency’ caps are acceptable provided they function effectively. Use of rags etc in place of a fuel cap must be regarded as a defect.
4. In the case of diesel fuel only a significant leak is dripping giving rise to a patch in excess of 75mm in 5 minutes. When considering several leaks, due regard must be given to the cumulative effect, which could justify prohibition action.
2
Categorisation of Defects April 08 1
Section 1 Part 2: Passenger Cars, Private BusesEngine and Associated Equipment and Light Goods Vehicles
2
Description of Defect Severity of Defect Action Notes
Exhaust System
Exhaust system incomplete/ insecure/ leaking
Exhaust silencer holed, missing or modified
Exhaust Emission
Exhaust emitting excessive smoke (see Notes 5 and 6)
Exhaust emitting excessive levels of pollutants (see Notes 5 and 6)
Fumes likely to enter vehicle interior or detachment imminent
Significant deterioration
Does not reduce the noise emitted to a reasonable level
Sufficient to obscure vision or likely to cause danger to other road users
Smoke levels exceed annual test standard by more than 10%, or continuous haze which tends to obscure vision
Exceeding the annual test limits by 10% or less or continuous haze, any colour
Sufficient to obscure vision or likely to cause danger to other road users
Emission levels exceed the annual test standard by more than 10%, or tends to obscure vision
Exceeding the annual test limits by 10% or less or continuous haze, any colour
Continuous emission of dense blue or clearly visible black smoke at idle
I
D
D
I
D
IN
I
D
IN
D
5. Petrol Engines: A visual assessment of exhaust smoke can be made on all vehicles. The prescribed limits for the various exhaust emission components, requiring an exhaust gas analyser to measure, are to be applied to vehicles first used on or after 1 August 1975.
The appropriate procedures and standards as set out in the relevant Inspection Manual will be applied according to the age and class of vehicle. For prohibition issue, where an analyser is used, a margin of 10% will be added to all prescribed limits.
6. Diesel Engines: A visual assessment of exhaust smoke can be made on all vehicles. As with vehicles with petrol engines, a 10% margin will also be allowed above the statutory limits. The Light Absorption Coefficient Scale used for diesel exhaust smoke, being logarithmic, results in the standards for delayed prohibition of >3.7m-1 for turbocharged, and >3.0m-1 for naturally aspirated engines.
April 08 VOSA 2
Part 2: Passenger Cars, Private Buses Section 1 and Light Goods Vehicles Engine and Associated Equipment
Description of Defect Severity of Defect Action Notes
Speed Limiter (see Note 7)
Speed limiter missing/ disconnected
Speed limiter not restricting the vehicle to its legal maximum
Speed limiter plate missing/ defective
Speed limiter tamperproof device missing/ defective/ showing evidence of disturbance
Evidence of intent to circumvent the speed restrictions
Unintentional non-compliance
Evidence of intent to circumvent the speed restrictions
Unintentional non-compliance but applicable restricted speeds clearly exceeded (>10kph)
Unintentional non-compliance but evidence that applicable speed limit is being generally complied with (margin <10kph)
-
-
I
D
I
I
D
IN
D
7. *If applicable to vehicle type and when first used.
a) Unintentional non-compliance will include those instances provided for in regulation where the speed limiter has become defective during it’s current journey even if the driver is aware. Providing the available evidence indicates the driver is generally complying with the applicable speed within 10 kph delayed prohibition action will be appropriate.
b) Some speed limiters do not require the fitting of external tamperproof devices. Action must only be taken where there is clear evidence that a device has been disturbed/ removed or is defective.
Any interrupter device fitted to the vehicle in contravention of the requirements
- I
2
Categorisation of Defects April 08 3
Part 2: Passenger Cars, Private Buses Section 2 and Light Goods Vehicles Transmission
Description of Defect Severity of Defect Action Notes
Drive/ Propeller Shafts
Drive/ propeller shaft damaged
Universal joint excessively worn, flangecracked or insecure on the drive/propeller shaft (See Note 1)
Drive/ propeller shaft flange boltsloose/ missing
Drive/ propeller shaft carrier bearingbadly worn, damaged or mountinginsecure
Front Wheel Drive Shafts Only
CV joint or shaft coupling excessivelyworn. CV gaiter split, missing orinsecure.
Bent, fouling or fractured and failureimminent
Other significant damage
Otherwise than above
Failure or detachment likely
Significantly defective
Otherwise than above
Shaft likely to become detached
Other significant insecurity
Otherwise than above
Failed or failure imminent
Other significant defect
Otherwise than above
Bearings collapsed or excessively worn,splines excessively worn or coupling/ jointseriously deteriorated and failure imminent
I
D
IN
I
D
IN
I
D
IN
I
D
IN
I
1. Prohibition action for excessive wear of universal joint is only justified when radial movement indicates that needle roller bearings are missing from one or more cups.
Significantly deteriorated component
Otherwise than above
D
IN
Categorisation of Defects April 08 5
2
Section 3 Part 2: Passenger Cars, Private BusesRunning Gear and Light Goods Vehicles
Description of Defect Severity of Defect Action Notes
2
Road Wheels and Hubs (See Note 2a)
Missing wheel(s)
Wheel fractured or welding breaking
-
Failure imminent (see Note 1)
I
I
1. Fracture at the bridge over the valve is not considered a reason for action.
2. On certain wheels, abutting with slight displacement is acceptable.
away
Wheel hub fractured
Otherwise than above
Failure or detachment imminent
D
I
2a. For spigot mounted wheels see IM6 Part I.
Otherwise than above D
Wheel stud holes elongated/ damaged If visible with wheel nuts in place or detachment likely
I
Any stud hole severely worn/ elongated D
Wheel stud or nut missing/ loose/ fractured/ not clamping or fully locating in taper
More than one wheel nut/ stud is missing, loose, fractured or obviously not clamping or locating in road wheel taper
I
Otherwise than above D
Tyre retaining ring abutting/ fractured (see Note 2)
The ring is visibly displaced from its seating and total displacement is imminent
I
Wheel seriously distorted Affecting steering or vehicle stability I
Otherwise than above IN
Wheel embellisher protruding or insecure
Sharp edges/points exposed, likely to cause injury or detachment imminent
I
Otherwise than above IN
April 08 VOSA 6
Part 2: Passenger Cars, Private Buses Section 3 and Light Goods Vehicles Running Gear
Description of Defect Severity of Defect Action Notes
Road Wheels and Hubs
Half shaft bolt/ nuts/ studs loose ormissing
Incompatible wheel fitted
Spare wheel
Spare wheel fractured/ badly distorted/stud holes elongated
Tyres
The nominal size, ply rating or load index/ speed rating of any tyre is below that appropriate for the vehicle. A tyre marked with a speed rating letter within the range A to K (See Notes 3 and 4)
Tyres of different types/ nominal sizes/ aspect ratio fitted on the same axle
Radial ply tyres fitted to front axle and crossply or bias belted to rear axle or bias belted to front axle and crossply to rear axle
A tyre not fitted in accordance with the manufacturers instructions
Loss of drive likely
Otherwise than above
Fouling other components where failure ofthe wheel or affected component is likely
Otherwise than above
-
Tyre obviously overloaded
Otherwise than above
Tyres of different type (ie crossply or radial) fitted
One tyre is of a different nominal size or aspect ratio from those on the same axle (See Notes 3 and 4)
(See Note 6)
(See Note 4a)
I
IN
I
IN
IN
I
D
I
D
I
IN
3. Manufacturer supplied ‘temporary use’ spares (‘Space-Savers’) are acceptable.
4. Private buses/ restricted speed vehicles are permitted ‘J’ or ‘K’ rated tyres provided they are of suitable capacity following deduction of any load penalty.
4a. For example tyres with a directional tread pattern incorrectly fitted.
5. It cannot be assumed that, because either tyre on a twin wheel is not in contact with the ground when the vehicle is stationary on a level surface, there is a difference in nominal size.
Unless marked otherwise, "standard" car tyres have a nominal aspect ratio of 82%. These can be safely mixed with tyres with an aspect ratio of 80%.
6. This does not apply to vehicles with twin or extra wide tyres on the rear axle, or to tyres manufactured for (and fitted to) engineering plant. It also does not apply to vehicles with a maximum speed not exceeding 30mph.
Categorisation of Defects April 08 7
2
Section 3 Part 2: Passenger Cars, Private BusesRunning Gear and Light Goods Vehicles
Description of Defect Severity of Defect Action Notes
2
Tyres
Tyre walls in contact
Tyre bulging
Tyre has a break in the fabric or deep cut (See Notes 9a and 9b)
Caused by under inflation or incorrect wheel fitting
Caused by separation or partial failure of its structure (See Note 8)
Body cords damaged
Cut 25mm or longer exposing body cords
IN
I
I
D
7. Recut tyres are permitted on
• motor vehicles of unladen weightexceeding 3050kg, between 2540kgand 3050kg if fitted to wheel rimsexceeding 405mm (16") diameter,and
• trailers of unladen weight exceeding1020kg (2290kg total weight forfixed plant carriers).
8. Bulging includes any lifting of thetread rubber and must not be confused with undulations which
Breaker cords damaged in the tread area
Breaker cords exposed in the tread area
D
IN
could be present due tomanufacturing imperfections.
9. The body cords are those extendingfrom bead to bead.
Tyre seriously under inflated or incorrectly seated on the wheel rim
Otherwise than above (See Note 9)
Likely to affect steering or, if laden, overload the other tyre on a twin fitment
IN
I
Although damage to such cords has adifferent effect on tyres of radial andcross ply construction, the problemsof differentiation are very complexand the stated standards must be
Otherwise than above IN applied.
Body cords must not be confusedwith the breaker cords in the tread area. The consequence of damageto breaker cords is not generally so severe. For this reason the different action is recommended.
9a. Cuts which are deep enough toreach the body cords or ply but areless than 25mm or 10% of the section width, whichever is thegreater, and have not damaged orexposed the body cords or ply donot breach the legal requirementsfor tyres.
April 08 VOSA 8
Part 2: Passenger Cars, Private Buses Section 3 and Light Goods Vehicles Running Gear
Description of Defect Severity of Defect Action Notes
Tyres
Tyre tread worn beyond legal limit (See Note 10)
Tyre fouling
Recut tyre fitted to a vehicle which should not have a recut tyre
Depth of tread is not at least 1.6mm throughout a continuous band (excluding tie-bars) situated in the central three-quarters of the breadth of tread, around the entire circumference on
• any tyre on a steered axle, or
• 50% or more of the total number of tyres fitted to non-steered axles
Otherwise than above
The base of any groove of the original tread pattern is not clearly visible (see Note 11)
Tyre damaged and / or likely to fail
Otherwise than above
Fitted to a vehicle on which recut tyres are not permitted (See Note 7)
I
D
IN
I
IN
IN
9b. “Exposed” for this purpose means the cords are visible or it can be established that they are exposed with the use of a probe.
10. For tyre tread requirements for vehicles with more than 8 passenger seats and goods vehicles with a gross vehicle weight exceeding 3500kg GDW consult Part 1 of this document.
11. "Original tread pattern" means
a. in the case of a retreaded tyre, thetread pattern immediately after thetyre was retreaded
b. in the case of a wholly recut tyre, themanufacturer’s recut tread pattern.
c. in the case of a partially recut tyre,on the part that has been recut, the manufacturer’s recut tread pattern,and on the other part, the treadpattern when the tyre was new.
Spare Tyre
Spare tyre bulging/ fabric cut/ fabric exposed/ tread worn below the legal limit
- IN
d. in the case of any other tyre, thetread pattern when the tyre was new.
Note: Grooves which wear out before the main grooves and other minor featuressuch as sipes, small lateral extensions tothe circumferential grooves and minorlateral grooving on the shoulders are tobe disregarded when consideringwhether the “original tread pattern” isvisible.
2
Categorisation of Defects April 08 9
Section 3 Part 2: Passenger Cars, Private BusesRunning Gear and Light Goods Vehicles
2
Description of Defect Severity of Defect Action Notes
Axles, Stub Axles and Wheel Bearings
Excessive lift in stub axles or swivel joints
Axle or Stub axle fractured or distorted
Excessive free play or roughness in wheel bearings (See also ‘King Pins’, Section 6)
Evidence of collapse of bearings/ joints or loss of shims
Otherwise than above (See Note 12)
Fractured
Otherwise than above
Likely to collapse
Otherwise than above
I
D
I
D
I
IN
12. As a general guide, the lift in a stub axle would normally be considered excessive if greater than 1.6mm.
April 08 VOSA 10
Section 4 Part 2: Passenger Cars, Private BusesSuspension and Light Goods Vehicles
Description of Defect Severity of Defect Action Notes
2
Springs
Spring leaf fractured Main leaf fractured or more than half of the intermediate leaves broken
I
Otherwise than above D
Spring weak Bodywork fouling or is likely to foul road wheels if vehicle were laden or seriously affecting vehicle’s stability and/ or control
I
Otherwise than above IN
Spring leaves displaced/ distorted/ damaged/ repaired by welding
Control of vehicle likely to be affected or failure of the spring imminent
I
Otherwise than above IN
Spring centre bolt broken or missing - I
Spring clips loose, missing or broken - IN
Spring holding down bolts loose or missing
Axle moving relative to spring
Otherwise than above
I
D
Coil spring incorrectly located, spring fractured or mounting loose
Detachment imminent/ safe control of vehicle likely to be affected
I
Otherwise than above D
April 08 VOSA 12
Part 2: Passenger Cars, Private Buses Section 4 and Light Goods Vehicles Suspension
Description of Defect Severity of Defect Action Notes
Anchor/ Shackle Pins
A suspension anchor/ shackle pin missing/ sheared
Anchor/ shackle pin and/ or bush excessively worn
A suspension anchor/ shackle pin insecure in its bracket
A suspension anchor/ shackle pin locking device missing/ ineffective/ insecurely fitted
(See Note 1)
Diametric clearance in excess of one third of pin diameter
Significantly worn
Otherwise than above (See Note 1)
Pin displaced
Significantly loose
Otherwise than above (See Note 1)
Missing or ineffective
Insecurely fitted (See Note 1)
I
I
D
IN
I
D
IN
I
D
1. This inspection is also applicable to the pins and bushes locating independent suspension arms and balance beam and linkage pivots.
Categorisation of Defects April 08 13
2
Section 4 Part 2: Passenger Cars, Private BusesSuspension and Light Goods Vehicles
2
Description of Defect Severity of Defect Action Notes
Spring Brackets
Spring slipper bracket excessively worn/ fractured/ not securely fixed/ rebound pin missing
Spring anchor bracket insecure/ fractured or otherwise defective
Spring bracket or mounting loose/ fractured/ seriously weakened by damage or corrosion
Torsion Bars
Torsion bar fractured/ distorted
Torsion bar anchorage loose
Bonded Units
A bonded attachment insecure/ fractured/ seriously weakeneddue to damage/ corrosion or failure ofbonding element
Spring displaced from slipper bracket
Otherwise than above (See Note 3)
Detachment or failure imminent
Fractured or relative movement between bracket and chassis
Any one nut, bolt or rivet missing/ insecure (See Note 2)
Detachment imminent
Otherwise than above (See Note 2)
Fracture, displacement or distortion adversely affecting directional control
Otherwise than above
Detachment imminent or affecting vehicle control or axle location
Otherwise than above
Failure imminent
Otherwise than above
I
D
I
D
IN
I
D
I
D
I
D
I
D
2. When some types of spring attachment bracket or suspension bracket are fitted there could be more holes in the bracket than holes in the chassis. This would not be a reason for action.
3. Delayed action only where a slipper is worn to the extent that it could, at the time of the inspection, clearly affect the movement or correct location of the road spring or has allowed the spring leaf to damage the chassis.
April 08 VOSA 14
Part 2: Passenger Cars, Private Buses Section 4 and Light Goods Vehicles Suspension
Description of Defect Severity of Defect Action Notes
Air Suspension
An air suspension unit or pipes Failure imminent I displaced/ damaged/ fouling other components/ seriously Otherwise than above D deteriorated/ leaking air
Suspension Arms/ Linkages/ Sub-frames
An arm, linkage or subframe Fracture, displacement or distortion I fractured/ displaced/ insecure/ distorted/ adversely affecting directional control or seriously weakened by corrosion failure imminent damage or wear/ is adjustable and has a loose adjustment or its locking device is Otherwise than above D insecure or missing.
Radius arm insecure Detachment imminent or likely to affect I steering
Otherwise than above D Shock Absorbers
Shock absorber missing/ loose/ fractured/ Missing, detachment imminent or likely to I malfunctioning affect steering
Otherwise than above D
Shock absorber leaking - IN
Categorisation of Defects April 08 15
2
Section 4 Part 2: Passenger Cars, Private BusesSuspension and Light Goods Vehicles
2
Description of Defect Severity of Defect Action Notes
Anti-roll bars
Anti-roll bar/ stabiliser missing
Anti-roll bar/ stabiliser insecure
Suspension Displacers
Any hydro-pneumatic suspension displacer unit, pipes or hoses leaking
Displacers, pipes or mountings weakened by corrosion
General
Fracture, serious distortion or excessive corrosion in a load bearing member within 30cm of any suspension component mounting
Missing (if a standard fitting)
Detachment imminent
Otherwise than above
Excessive leakage indicating failure, or failure imminent
Otherwise than above
Failure imminent
Otherwise than above
Failure or detachment imminent
Otherwise than above
I
I
IN
I
D
I
D
I
D
April 08 VOSA 16
Part 2: Passenger Cars, Private Buses Section 5 and Light Goods Vehicles Brakes
Description of Defect Severity of Defect Action Notes
Controls
Hand brake lever/ foot brake pedal fractured/ incomplete/ seized/ insecure
Hand brake lever/ foot brake pedal travel impeded/cannot be readily operated
Excessive side play in hand brake lever
Insufficient reserve travel on hand brake lever/ foot brake pedal
Hand brake lever pawl and/ or ratchet worn
Foot brake pedal antislip provision/missing/ loose/ deteriorated/ wornsmooth (See Note 1)
Foot brake pedal "creeps" to floor (SeeNote 2)
Foot brake pedal excessively "spongy"indicating a fault in the system (SeeNote 2)
Fails to fulfil its function or failure imminent
Otherwise than above
Cannot be operated satisfactorily
Otherwise than above
Failure imminent or could inadvertently disengage
Otherwise than above
Brake efficiency impaired
Otherwise than above
Lever cannot be set or could inadvertently disengage
Otherwise than above
Pad about to become detached or level of grip offered affected
Otherwise than above
-
Brake efficiency impaired
Otherwise than above
I
D
I
D
I
IN
I
D
I
IN
D
IN
I
I
D
1. The provision of a pedal rubber which is itself of an anti-slip material is not to be regarded as defective if its design pattern is worn smooth.
2. Defect might not apply to vehicles equipped with full air/ vacuum or continuous flow hydraulic braking systems.
For power assisted systems the engine might need to be running to do these checks.
Categorisation of Defects April 08 17
2
Section 5 Part 2: Passenger Cars, Private BusesBrakes and Light Goods Vehicles
Description of Defect Severity of Defect Action Notes
2
Controls 3. If a vehicle has a reservoir that is integral with the servo unit and has no
Brake hand valve fractured/ damaged/ If not functional I other reservoir and no warning device insecure is fitted, this is not automatically a
Otherwise than above D reason for action since some systems need not have a warning device.
Brake hand control valve cannot be - I moved over its original full travel or 4. Vehicles used from 1 April 1983 can cannot be retained in the on or off be fitted with either a visual warning positions device or an audible device. If both
are fitted only one need work. Parking brake hand valve lever cannot - I Vehicles first used before 1 April 1983 be set must be fitted with a visual warning
device. If an audible warning device is Warning Systems also fitted this is considered to be an
addition to the mandatory Warning gauge/ flag/ light missing/ not Where only one such device is fitted I requirement. functioning/ not visible
Otherwise than above IN 5. Items under Warning Systems apply (See Notes 3, 4 and 5) to all vehicles registered on or after 1
October 1937, except vehicles under Warning gauge not illuminated Function not readily visible during the hours IN 3,050kg unladen and
of darkness (See Notes 3, 4 and 5) • fitted with a vacuum reservoir
Warning buzzer inoperative (See Notes 3, 4 and 5) IN coupled direct to the induction manifold of the engine or
Anti lock brake warning light sequence - D inoperative/ incorrect • a reservoir in a servo unit.
Air/ Vacuum Assistance
Air/ vacuum assistance not working. - I Compressor or vacuum pump insecure or drive system missing or defective
April 08 VOSA 18
Part 2: Passenger Cars, Private Buses Section 5 and Light Goods Vehicles Brakes
Description of Defect Severity of Defect Action Notes
Air/ Vacuum Assistance
Insufficient reserve of air/ vacuum
Loss of air/ vacuum
Air/ vacuum build up slow
Actuators
Air/ vacuum actuator insecure/ damaged/ fractured/ excessively corroded/ incorrectly fitted
Excess travel of brake actuator
Insufficient pressure or vacuum to give assistance for two or more applications of the brakes after the warning device has operated (See Note 6)
Pressure/ vacuum cannot be sustained with engine running just above idling speed with or without brakes applied
Otherwise than above
Warning device fails to cease operating or gauge does not reach 3.1kg/ sq cm (45 psi/ 3 bar/ 310 kPa) within 6 minutes or 25 to 30cm vacuum in 2 minutes
Warning device fails to cease operating or gauge does not reach 3.1kg/ sq cm (45 psi/ 3 bar/ 310 kPa) within 3 minutes or 25 to 30cm vacuum in 1 minute (See Note 6)
Failed or failure imminent
Otherwise than above
Brake efficiency impaired
Excess amount of travel
Otherwise than above
IN
I
D
I
D
I
D
I
D
IN
6. If the vacuum gauge has no warning mark, take the 25 to 30cm mark as the warning mark. Some vehicles do not have gauges or warning devices.
Categorisation of Defects April 08 19
2
Section 5 Part 2: Passenger Cars, Private BusesBrakes and Light Goods Vehicles
2
Description of Defect Severity of Defect Action Notes
Servos
Brake servo insecure
Brake servo damaged/ incorrectly fitted/ fractured/ excessively corroded
Excessive travel of brake servo
Servo losing vacuum
Inlet manifold vacuum servo assistance inoperative/ vacuum pipe defective
Brake Travel/ Adjustment Indicators
Brake piston/ diaphragm travel indicator missing/ inoperative
Brake adjustment indicator shows that brake adjustment is necessary
Detached or detachment imminent
Otherwise than above
Failed or failure imminent
Otherwise than above
Brake efficiency impaired
Otherwise than above
Vacuum cannot be sustained with engine running above idling speed and brake applied
Otherwise than above
Brake efficiency impaired
Otherwise than above (See Note 7)
(See Note 8)
Brake efficiency impaired
Otherwise than above
I
D
I
D
I
IN
I
D
I
D
IN
I
D
7. Only applicable to vehicles equipped with a brake servo-system powered from the engine inlet manifold.
8. Brake actuators or servos in which the travel cannot be visually assessed are often fitted with a device that indicates the extent of travel of the piston or diaphragm.
April 08 VOSA 20
Part 2: Passenger Cars, Private Buses Section 5 and Light Goods Vehicles Brakes
Description of Defect Severity of Defect Action Notes
Brake Valves 9. Minor valves may not be supported.
Brake valve inoperative (specify - I 10. Faults, particularly those concerning component) the free movement of valves, are
often difficult to positively detect. If Brake valve insecure (specify Detached or detachment imminent and/ or I examiners are in any doubt about component) likely to cause leakage at connection the existence of a defect the IN
option must be used. Insecurity due to weakness or failure of D supporting structure (See Note 9)
Brake valve damaged/ fractured/ To an extent that renders the valve I excessively corroded (specify inoperative or failure imminent component)
Otherwise than above IN
Brake valve leaking Leakage such that pressure or vacuum I cannot be sustained with engine running just above idling speed
Otherwise than above D
Load sensing valve seized, linkage Clearly not able to function as intended I defective, missing or out of adjustment (See Note 10)
Otherwise than above IN Excessive oil/ contaminant discharge - D from brake valves
Air/ Vacuum Reservoir
Brake air/ vacuum reservoir About to become detached or failure I damaged/ excessively corroded/ insecure imminent
Otherwise than above D
Categorisation of Defects April 08 21
2
Section 5 Part 2: Passenger Cars, Private BusesBrakes and Light Goods Vehicles
2
Description of Defect Severity of Defect Action Notes
Hydraulic Systems
Brake master cylinder/ reservoir/ wheel cylinder/ caliper insecure
Brake master cylinder/ wheel cylinder/ caliper damaged/ incorrectly fitted/ fractured/ severely corroded/ reservoir cap missing
Brake fluid leaking from ... (specify source)
Warning/ light missing/ not functioning. Brake warning buzzer inoperative (See Note 11)
Hydraulic pressure build-up slow (See Note 11)
Hydraulic cylinder mounting insecure
(See Notes 9, 10 and 12)
Detached or detachment imminent
Otherwise than above
Failed or failure imminent
Otherwise than above
Obvious leak leading to brake failure or presenting risk of fire
Otherwise than above
If only means of warning
Otherwise than above
Warning device fails to cease operating within 6 minutes
Warning device fails to cease operating within 4 minutes
Detached or detachment imminent
Otherwise than above
I
D
I
D
I
IN
I
IN
I
D
I
D
11. Defects apply to continuous flow hydraulic braking systems.
12. Fully floating cylinders must not be confused with insecure cylinders.
April 08 VOSA 22
Part 2: Passenger Cars, Private Buses Section 5 and Light Goods Vehicles Brakes
Description of Defect Severity of Defect Action Notes
Hydraulic Systems
Absence of hydraulic brake fluid from reservoir or fluid level dangerously low
Mechanical Components
Any brake component excessively worn/ corroded/ fractured/ reduced in diameter/ number of strands reduced (specify component)
Any retaining/ locking device missing/ loose (specify component)
Brake lining/ pad missing/ excessively worn/ insecure
Reservoir empty
Fluid level clearly below the minimum level indication
Otherwise than above
Failed or failure imminent
Serious reduction of strength / excessively worn or displaced
Otherwise than above
Retaining device missing or detached
Retaining device insecure or locking device missing or insecure
Missing, detached or braking efficiency impaired
Linings worn to excess
Brake wear warning device activated
Otherwise than above
I
D
IN
I
D
IN
I
D
I
D
IN
IN
Categorisation of Defects April 08 23
2
Section 5 Part 2: Passenger Cars, Private BusesBrakes and Light Goods Vehicles
2
Description of Defect Severity of Defect Action Notes
Mechanical Components
Severely contaminated pad/ lining material
Brake disc fractured/ excessively worn/ pitted/ insert insecure (See Note 13a)
Brake drum fractured/ excessively worn (See Note 13a)
Any component seized/ restricted/ fouling/ excessive travel (specify component)
Brake backplate/ disc loose
Abnormal movement of levers indicating maladjustment (See Note 14)
Braking efficiency impaired (See Note 13)
Where contamination is clearly evident and likely to effect performance but brake test equipment not available to confirm
Otherwise than above
Failed or failure imminent
A fracture extending through the surface into the ventilation cavity
Otherwise than above
Failed or failure imminent
Drum fractured through
Otherwise than above
Brake efficiency impaired
Otherwise than above
Brake efficiency impaired
Otherwise than above
Brake efficiency impaired
Otherwise than above
I
D
IN
I
D
IN
I
D
IN
I
D
I
D
I
D
13. When immediate action is taken this must be reinforced with evidence that the efficiency is impaired, ie. brake test result or, in the case of adjustment, clearly no reserve travel.
13a. Surface cracks on brake discs and drums are a normal feature which should be ignored.
14. Excess travel means when there is no reserve travel left or the amount of movement clearly demonstrates that the point at which adjustment was necessary has been exceeded.
April 08 VOSA 24
Part 2: Passenger Cars, Private Buses Section 5 and Light Goods Vehicles Brakes
Description of Defect Severity of Defect Action Notes
ABS Components
Any component forming part of an anti-lock braking system missing/ damaged/ disconnected/ malfunctioning
Brake Pipes and Hoses
Brake pipe excessively chafed or damaged
Brake pipe corroded
Brake pipe inadequately clipped/ supported
Brake pipe fouling (specify component fouled)
Such that the ABS system is rendered inoperative or spurious signals are given
Otherwise than above
Failed or failure imminent
Otherwise than above (See Note 14a)
Failed or failure imminent
Deeply pitted and weakened
Otherwise than above
Failed or failure imminent
Significantly insecure
Otherwise than above
Failed or failure imminent
Otherwise than above
D
IN
I
D
I
D
IN
I
D
IN
I
D
14a. Minor damage that is unlikely to get worse can be ignored.
Categorisation of Defects April 08 25
2
Part 2: Passenger Cars, Private Buses Section 5 and Light Goods Vehicles Brakes
Description of Defect Severity of Defect Action Notes
Brake Pipes and Hoses
Brake hose chafed/ deteriorated/ stretched/ bulging/ kinked/ twisted/ fouling / exposed to excessive heat
Failed or failure imminent
Otherwise than above (See Note 14a)
I
D
15. Where legally required to be fitted (see vehicle technical record if appropriate).
Brake pipe/ hose/ coupling/ connection leaking (specify component)
Additional Braking Devices/ Retarders/ Exhaust Brakes
Not working/ missing
A device or component insecure/ damaged/ contaminated/ leaking gas or oil
Wiring chafed/ insecure/ poor condition
Any positive hydraulic leak
Leakage such that pressure or vacuum cannot be sustained with engine running just above idling speed
Otherwise than above
(See Note 15)
Likely to become detached, fire hazard or continuous oil leak
Oil leakage in excess of 75mm diameter patch in 5 minutes
Fire hazard
Otherwise than above
I
I
D
D
I
D
I
IN
Categorisation of Defects April 08 27
2
Section 5 Part 2: Passenger Cars, Private BusesBrakes and Light Goods Vehicles
Description of Defect Severity of Defect Action Notes
2
Service Brake Operation and Performance
Service brake does not operate on every road wheel
Service brake efficiency low
-
Performance does not meet prescribed C&U requirements (specify)
A malfunction indicated by abnormally low effort in excess of the annual test imbalance criteria (See Note 17)
Performance below normal expectation (See Note 16)
I
I
D
IN
16. Examiners must, where possible, take into account the design or kerb weight of the vehicle as appropriate. Where vehicles are tested on a roller brake tester, the appropriate Inspection Manual criteria must be used.
17. Action under this section is confined to cases where the minimum efficiency prescribed in C&U is met but abnormally low effort is identified indicating a serious brake malfunction.
Service brake unbalanced Marked deviation from straight path when brakes applied
I
Otherwise than above IN
Service brake binding excessively Severely overheated and either failure or fire likely
I
Otherwise than above IN
Service brake ‘grabbing’ or ‘juddering’ Such as to affect directional control I
Otherwise than above IN
April 08 VOSA 28
Part 2: Passenger Cars, Private Buses Section 5 and Light Goods Vehicles Brakes
Description of Defect Severity of Defect Action Notes
Parking Brake Operation and 18. On a three-wheeled vehicle, the Performance parking brake needs to operate on
only one wheel. Parking brake does not operate on at - I least two road wheels (See Note 18) 19. Action under this section is confined
to cases where the minimum Parking brake inefficient Does not meet prescribed C&U I efficiency prescribed in C&U is met
requirements (specify) but abnormally low effort is identified indicating a serious brake
Little or no braking effort on a roadwheel on D malfunction. which the brake is designed to operate (See Note 19)
Performance below normal expectation IN (See Note 19)
Parking brake binding excessively Severely overheated and either failure or I fire likely
Otherwise than above IN General
Fracture, serious distortion or excessive Failure or detachment imminent I corrosion in main chassis, crossmember or load bearing panel within 30cm of a Otherwise than above D brake control mounting.
Categorisation of Defects April 08 29
2
Section 6 Part 2: Passenger Cars, Private BusesSteering and Light Goods Vehicles
Description of Defect Severity of Defect Action Notes
2
Steering Wheel and Column 1. The maximum permissible ‘free’ play on a steering wheel is as follows:
Excessive ‘free’ play at steering wheel Likely to impair directional control of the vehicle
Otherwise than above (See Notes 1 and 2)
I
D
If a point on the rim of the steering wheel moves without the road wheels moving for a distance of
Steering wheel hub, rim or spokes insecure
Detachment imminent
Otherwise than above
I
D
• (except on rack and pinion steering)1/ 5 of diameter of steering wheel,eg 76mm on a 380mm diameterwheel.
Steering wheel hub, rim or spokes Failed or failure imminent or jagged edges I • (on rack and pinion steering) 1/ 30fractured likely to cut driver’s hand
Otherwise than above (See Note 3) D
of diameter, eg 13mm on a 380mmdiameter wheel. Free play of up to1/ 8 of diameter, eg 48mm on a380mm diameter wheel is acceptable where the steering wheel
Steering wheel loose to column shaft - I - is placed forward from rack and
Steering wheel retaining device missing - I pinion steering, and (specify device) - has a number of joints to the rack.
2. Power steering must be checked withthe engine running. While the powersteering pump is working but notproviding hydraulic assistance, thesteering wheel play is slightly greaterthan with manual steering systems.
3. Cracks in the plastic covering of aspoke do not necessarily indicate thatthe spoke is fractured. Jagged edgeson the rim of a steering wheel (eg dueto cracks in plastic covering) are areason for action only if they are likelyto cut the driver’s hand.
April 08 VOSA 30
Part 2: Passenger Cars, Private Buses Section 6 and Light Goods Vehicles Steering
Description of Defect Severity of Defect Action Notes
Steering Wheel and Column 4. Some vehicles have flexible top bearings for the steering column, in
Excessive lift or movement of steering Abnormal movement indicating failure of I which case more than average column component parts movement is permissible.
Otherwise than above (See Notes 4 and 5) D 5. In certain types of steering eg: those fitted with universal joints or flexible
Steering column flexible coupling or Failure imminent I couplings, there could be a certain universal joint deteriorated/worn/insecure amount of movement present that is
Otherwise than above (See Notes 4 and 5) D not due to wear.
Steering wheel column adjuster defective Steering wheel column cannot be secured I 6. If the vehicle is fitted with power as required steering the engine must be running
Steering Box/Rack & Pinion (See Note 6) when the steering is operated.
Steering stiff Restricting operation I
Steering box/ rack noisy/ knocking Obvious roughness D Otherwise than above IN
Steering box sector shaft twisted Shaft visibly twisted I
Excessive lift/ end float on sector shaft, - D bushes or splines
Excessive lift in steering rack - D
Steering gear housing Any restriction, failure or detachment I fractured/ insecure/ damaged imminent
Otherwise than above D
Steering rack gaiter - D missing/ split/ damaged or displaced
Categorisation of Defects April 08 31
2
Section 6 Part 2: Passenger Cars, Private BusesSteering and Light Goods Vehicles
Description of Defect Severity of Defect Action Notes
2
Steering Linkage
Steering drop arm loose If movement is such that failure is likely
Excessive abnormal movement
I
D
7. Some steering joints are spring loaded. The designed amount of movement must not be confused with abnormal movement.
Steering ball pin insecure Any insecurity I
Steering ball pin grooved Diameter substantially reduced I
Otherwise than above IN
Track rod/ drag link loose/ misaligned Excessive movement between mating parts (See Note 7)
I
Slight movement (See Note 7) D
Misaligned only IN
Excessive movement in steering joint If joint in danger of separation I
Excessive abnormal movement (See Note 7)
D
Otherwise than above IN
Steering relay arm pivot excessively worn
Failure imminent
Otherwise than above
I
D
Steering relay arm pivot housing/ bracketfractured/ insecure
Failure or detachment imminent
Otherwise than above
I
D
Steering arm loose Detachment imminent I
Otherwise than above D
April 08 VOSA 32
Part 2: Passenger Cars, Private Buses Section 6 and Light Goods Vehicles Steering
Description of Defect Severity of Defect Action Notes
Steering Linkage
Steering component fractured/ deformed/ insecure/ excessively corroded/ repaired by welding/ fracture, serious distortion or excessive corrosion in a load bearing member within 30cm of mounting (specify component)
Steering component fouling, or road wheels or tyres fouling/ restricted in travel (specify component)
Steering retaining/ locking device missing/ insecure (specify component)
Power Steering
Power steering inoperative(malfuctioning or otherwise defective)
Pump insecure or it’s drive systemmissing or defective
Power steering, ram anchor bracket orpump mounting fractured/ insecure orotherwise defective
Power steering ram fluid pipes damaged
Power steering pipes fouling (specifypart of vehicle being fouled)
Failure or detachment imminent
Otherwise than above
Steering function impaired
Otherwise than above
Retaining device missing or ineffective
Retaining device insecure or any lockingdevice missing or insecure
Disconnected, inoperative or failureimminent (See Note 8)
Failure or detachment imminent
Otherwise than above
Failure or detachment imminent
Otherwise than above
Steering function impaired
Otherwise than above
Pipes damaged and likely to fail
Otherwise than above
I
D
I
D
I
D
I
I
D
I
D
I
IN
I
IN
8. If power steering is optional and removal has no adverse effect on the steering, no action should be taken.
Categorisation of Defects April 08 33
2
Section 6 Part 2: Passenger Cars, Private BusesSteering and Light Goods Vehicles
2
Description of Defect Severity of Defect Action Notes
Power Steering
Excessive fluid/ air leakage from power steering (specify component)
Power steering ram joint excessively worn/ spring very weak/ spring broken
King Pins
Excessive wear of king pin and/ or bushes or swivel joint or MacPherson strut assembly
King pin loose in axle beam or swivel joint worn/ insecure
King pin or swivel joint retaining device missing/ insecure
Fluid/ air leaking continuously, failure of power steering imminent
Contamination of materials so as to constitute a fire risk
Fluid leak in excess of 75mm diameter patch in 5 minutes
Otherwise than above
Joint in danger of separation, or detachment of ram imminent
Otherwise than above
Likely to affect steering or fail prematurely
Otherwise than above (See Note 9)
Pin displaced or displacement or failure likely
Otherwise than above
Retaining device missing or detached
Retaining device insecure
I
I
D
IN
I
D
I
D
I
D
I
D
9. It is not practicable to lay down precise limits, but the following is a guide to determine acceptable wear at king pins.
With the wheel braked and off the ground, note the total measured movement at the outer wall of the tyre when the wheel is rocked.
For 355mm wheels this must not exceed 6mm.
The maximum permissible movement for wheels of other diameters must be in proportion to this.
April 08 VOSA 34
Part 2: Passenger Cars, Private Buses Section 7 and Light Goods Vehicles Chassis
Description of Defect Severity of Defect Action Notes
Chassis and Attachments
Chassis main member/ body structure/ cross member/ outrigger severely corroded/ seriously deformed/ fractured/ displaced/ insecure/ missing
Excessive corrosion, cracks or damage of a load bearing member within 30cm of a body mounting.
Spare wheel carrier or wheel insecure (See Note 3)
Trailer Coupling (See Note 4)
Coupling on vehicle
Deformed or cracked pin, jaw, hook or ball
Mounting of jaw, hook or ball to chassis insecure
Locking device missing, inadequate, damaged or ill-fitting
Worn pin, jaw, hook or ball
Likely to affect control of the vehicle, safe carriage of load or detachment of component imminent
Otherwise than above (See Notes 1 and 2)
Detachment imminent
Otherwise than above
Detachment imminent and likely to fall from vehicle
Otherwise than above
Trailer security adversely affected
Failure or detachment imminent
Locking device ineffective
Otherwise than above
Thickness of metal at any point reduced to 2/3 or less of its original thickness and trailer attached
No trailer attached
I
IN
I
IN
I
IN
I
I
I
D
I
D
1. For components normally fixed to the chassis e.g. fuel tanks, brake reservoirs etc, see other sections.
2. This item includes the condition of any flitch plates that are fitted.
3. Only applicable to vehicles with separate carriers or wheels mounted on the underbody.
4. For information regarding fifth wheel defects refer to Part I of this document.
Categorisation of Defects April 08 35
2
Section 7 Part 2: Passenger Cars, Private BusesChassis and Light Goods Vehicles
2
Description of Defect Severity of Defect Action Notes
Ball excessively worn
Safety locking device missing/ not operating
Excessive wear in or insecurity of any member or securing device
Security spring weak or broken
A load bearing part of coupling cracked
Worn to such an extent that the safe coupling of the trailer is unlikely to be achieved
Otherwise than above
(See Note 5)
Failure or detachment imminent (Trailer attached)
Otherwise than above
Broken and trailer attached
Weak or otherwise than above
Failure or detachment likely (Trailer attached)
Otherwise than above
I
D
D
I
D
I
IN
I
D
5. Some couplings do not require a safety locking device. Action must only be taken where there is clear evidence that a device is, or has been, fitted.
April 08 VOSA 36
Part 2: Passenger Cars, Private Buses Section 7 and Light Goods Vehicles Chassis
Description of Defect Severity of Defect Action Notes
Coupling on Trailer
Draw bar cracked or deformed Seriously cracked or fractured
So seriously deformed that use would cause danger
I
I
6. Applies to trailers exceeding 750kg total design axle weight, manufactured on or after 1 April 1995 and all trailers manufactured on or after 1 January 1997.
Otherwise than above IN
Mounting or draw bar to trailer insecure Failure or detachment imminent I
Otherwise than above D
Draw bar eye or ball socket deformed, cracked or excessively worn
Trailer security affected
Otherwise than above
I
D
Locking device missing, inadequate, damaged or ill-fitting
Locking device ineffective
Otherwise than above
I
D
King pin attachment excessively worn, cracked or insecure
- I
Worn operating member Detachment imminent I
Otherwise than above IN
Worn draw bar attachment pins andbrackets
The thickness of metal at any point reducedto 2/3 or less of its original thickness
I
Significant reduction in thickness D
‘Breakaway’ cable/ chain missing/ damaged/ defective
(See Note 6) D
Categorisation of Defects April 08 37
2
Section 8 Part 2: Passenger Cars, Private BusesVehicle Interior and Light Goods Vehicles
2
Description of Defect Severity of Defect Action Notes
Driving Controls
Driving control missing/ incomplete/ fractured/ damaged/ excessively corroded/ impeded in its travel/ incorrectly positioned/ insecure (specify component)
Clutch pedal anti-slip pad loose/ deteriorated
Control so defective or impeded in its travel that it fails to fulfil its function
Otherwise than above
If originally fitted
I
IN
IN
Driver’s Area and Fittings
Floor around driver insecure/ badlyweakened
Driver’s seat loose on its mounting orframe fractured or seriously weakened
Driver’s seat adjustment inoperative/badly worn
Component/ fitting in driver’s areadamaged
Affects driving control or safety of driver
Otherwise than above
Seat so loose or weakened that it could cause the driver to lose control of the vehicle
Otherwise than above
Seat likely to move inadvertently or cannotbe located
Seat cannot be adjusted
Damaged or installed in such a way aslikely to cause injury
Otherwise than above
I
IN
I
IN
I
IN
I
IN
April 08 VOSA 38
Part 2: Passenger Cars, Private Buses Section 8 and Light Goods Vehicles Vehicle Interior
Description of Defect Severity of Defect Action Notes
Driver’s Area and Fittings
Obligatory rear view mirror and/ or glass missing/ insecure/ damaged
Driver’s view to the front impaired having regard to the original design of the vehicle
Speedometer not fitted/ incomplete/ cannot be illuminated/ inoperative/ cannot be readily seen by driver
Horn missing/ insecure/ inoperative
Driver’s area littered with rubbish/ ancillary equipment
Passenger Seats
Passenger seat insecure
If view to the rear is inadequate
External mirror likely to become detached
Otherwise than above
Any object seriously impairing driver’s view throughout the area swept by the windscreen wipers
Otherwise than above
(See Note 1)
Detachment imminent
Otherwise than above
Liable to interfere with proper control of the vehicle
Otherwise than above
Likely to become displaced
Otherwise than above
I
I
IN
I
IN
IN
I
IN
I
IN
I
IN
1. Vehicles first registered on or after 1 October 1937 are required to be fitted with a speedometer unless the vehicle is legally limited to a speed not exceeding 25mph or is one which is incapable by reason of its construction of exceeding 25mph.
Categorisation of Defects April 08 39
2
Section 8 Part 2: Passenger Cars, Private BusesVehicle Interior and Light Goods Vehicles
Description of Defect Severity of Defect Action Notes
2
Passenger Seats 2. The legal requirements for the fitment of seat belts are complex and are not
Passenger seat frame fractured or seat Likely to cause injury I included in this Guide. For further damaged details please refer to the appropriate
Likely to tear clothing D Inspection Manual for the class of vehicle being examined.
Otherwise than above IN Seat Belts
Any obligatory seat belt not fitted where - D legally required or wrong type of belt fitted (See Note 2)
Any obligatory or non-obligatory seat - D belt not securely fixed to the seat or to the structure of the vehicle
Any obligatory or non-obligatory seat A cut or serious deterioration in any part of D belt webbing damaged or deteriorated. A the seat belt webbing or a seat belt stalk seat belt stalk deteriorated.
Any obligatory or non-obligatory seat Mechanism does not secure or release the D belt locking mechanism or retraction belt as intended when the webbing is mechanism faulty pulled, webbing does not retract
Excessive corrosion, serious distortion - D or a fracture in any load bearing part of the vehicle structure within 30cm of a seat belt anchorage.
April 08 VOSA 40
Part 2: Passenger Cars, Private Buses Section 9 and Light Goods Vehicles Bodywork
Description of Defect Severity of Defect Action Notes
Body Panelling
Exterior body panel damaged/ missing / protruding/ insecure/ corroded
Interior side panel/ damaged/ missing/ protruding/ insecure
Any embellishment protruding/ damaged / insecure (specify component)
Bumpers
Bumper insecure or damaged
Likely to become detached or to cause injury or permit the load to be shed or leaked
Otherwise than above
Likely to become detached or to cause injury
Otherwise than above
Likely to become detached or to cause injury
Otherwise than above
Detachment likely either partially or completely or having projections or jagged edges likely to cause injury
Otherwise than above
I
IN
I
IN
I
IN
I
IN
Categorisation of Defects April 08 41
2
Section 9 Part 2: Passenger Cars, Private BusesBodywork and Light Goods Vehicles
Description of Defect Severity of Defect Action Notes
2
Wings and Wheel Arches
Wing missing Presenting a risk of injury I
Otherwise than above IN
Wing insecure Detachment likely or rubbing on a tyre I
Otherwise than above IN
Wing badly holed/ corroded/ damaged Holed/ corroded/ damaged such that edges I are likely to cause injury
Otherwise than above IN
Insufficient clearance between wing and Wing rubbing or likely to rub on tyre, I tyre particularly when laden, and thereby cause
damage to the tyre or a danger of injury e.g. fire risk, steering affected etc.
Otherwise than above IN Registration Plates and VIN Details
Registration mark letters or numbers Likely to be misread D incorrectly formed
A registration plate missing/ broken/ - IN incomplete/ insecure/ faded/ dirty/ deteriorated/ obscured. Letters or figures incorrectly spaced or formed
A vehicle identification number not - IN displayed/ illegible
April 08 VOSA 42
Part 2: Passenger Cars, Private Buses Section 9 and Light Goods Vehicles Bodywork
Description of Defect Severity of Defect Action Notes
Windscreen and Windows
Windscreen or window cracked/ scratched/ damaged/ discoloured/ obscured or vision obstructed/ insecure
Windscreen not of safety glass
Window not of safety glass
Window glazing insecure/ cracked
Windscreen and/ or front side windows excessively tinted
Washers and Wipers (See Note 4)
Windscreen wiper missing/ inoperative/ blades worn/ does not operate over an adequate area
Windscreen washer not fitted/ inoperative/ system incomplete/ inadequate
Driver’s view of the road seriously impaired/ presents a danger to occupants of the vehicle/ detachment likely
Otherwise than above
(See Notes 1, 2 and 3)
(See Notes 1, 2 and 3)
Missing, detachment likely and/ or presents a risk of injury
Otherwise than above
Average light transmission <30% Average light transmission >30%, <45% Average light transmission >45%, <65%
Any wiper missing or inoperative such as to impair driver’s view
Subject to prevailing weather conditions (i.e. weather fine)
Otherwise than above
Vision seriously impaired
Otherwise than above
I
IN
I
D
I
IN
I D IN
I
D
IN
I
IN
1. In the case of goods vehicles first used on or after 1 January 1959, the glass of windscreens and all windows in front of and on either side of the driver’s seat must be of safety glass.
2. In the case of passenger or dual-purpose vehicles first used on or after 1 January 1959, if glass is fitted to the windscreen or any outside windows it must be safety glass.
3. In the case of vehicles first used on or after 1 June 1978, windscreens and windows wholly or partly on either side of the driver’s seat must be of specified safety glass. All other windows must be specified safety glass or safety glazing.
4. If the windscreen can be opened or by some other means an adequate view can be obtained from the driving seat, the vehicle need not be provided with wipers or washers.
2
Categorisation of Defects April 08 43
Section 9 Part 2: Passenger Cars, Private BusesBodywork and Light Goods Vehicles
Description of Defect Severity of Defect Action Notes
2
Doors 5. This applies to the driver’s and front passenger doors on a car, or any
Door jammed/ obstructed/ cannot be Jammed, obstructed or deliberately secured I door on a bus, but if the door opened from inside or outside so that it cannot be opened from inside or opposite to the driving side of a goods
outside (See Note 5) vehicle is rendered inoperative deliberately, it must be considered to
Door, boot lid, tailgate, loading door, - I be an integral part of the cab. tailboard, dropside cannot be retained in the closed position 6. Most bonnets are fitted with two
securing methods and due regard Door hinges/ catches/ pillars worn/ Door is very difficult to shut or could fly I must be taken of the effectiveness of loose/ insecure/ weakened open inadvertently both where fitted.
Otherwise than above IN
Door stiff to operate Unable to fully open or close I
Otherwise than above IN
Sliding door jammed/ cannot be secured Jammed or cannot be secured I in the open or closed positions/ cannot be opened and closed without excessive Otherwise than above IN effort (See Note 5)
Bonnet
Bonnet catches missing/ damaged/ Bonnet could inadvertently open obscuring I defective (See Note 6) driver’s view
Otherwise than above IN
April 08 VOSA 44
Part 2: Passenger Cars, Private Buses Section 10 and Light Goods Vehicles Electrical Equipment
Description of Defect Severity of Defect Action Notes
Battery
Battery insecure Likely to fall from vehicle or displacement I constitutes risk of fire
Otherwise than above IN
Battery leaking or cell closures Electrolyte likely to cause imminent failure I loose/ missing of items which could affect vehicle safety or
entering passenger compartment
Otherwise than above IN Switchgear and Wiring
Wiring insecure/ inadequately Constitutes a fire risk I insulated/ insulation is or will become ineffective due to chafing or heat Otherwise than above IN
Lighting switch insecure/ malfunctioning - IN
Categorisation of Defects April 08 45
2
Section 11 Part 2: Passenger Cars, Private BusesLamps and Reflectors and Light Goods Vehicles
Description of Defect Severity of Defect Action Notes
2
All lamps 1. No lamps or reflectors are required to be fitted to vehicles only used on
A lamp lens insecure or damaged Likely to cause injury or detachment I roads between sunrise and sunset. imminent
Obligatory Front Position Lamps (See Note 1)
Obligatory front position lamp insecure Lamp so insecure that detachment is I imminent
Otherwise than above IN
Obligatory front position lamp - IN inoperative/ missing/ dim/ obscured/ shows light of wrong colour/ otherwise not in good working order
Obligatory front position lamp has - IN intermittent operation, flickers when tapped, is affected by the operation of another lamp, does not face the front or is incorrectly positioned
April 08 VOSA 46
Part 2: Passenger Cars, Private Buses Section 11 and Light Goods Vehicles Lamps and Reflectors
Description of Defect Severity of Defect Action Notes
Obligatory Rear Position Lamps 2. This action is appropriate only (See Note 1) between sunset and sunrise or in
conditions of seriously reduced Obligatory rear lamp insecure Lamp so insecure that detachment is I visibility.
imminent 3. Rear fog lamps are required by
Otherwise than above IN vehicles first used on or after 1 April 1980 which have a width greater than
Obligatory rear lamp inoperative/ Likely to prevent width and presence of I 1300mm and a maximum speed missing/ dim/ obscured/ shows light of vehicle being indicated adequately during exceeding 25mph. wrong colour/ otherwise not in good compulsory use (See Note 2) working order 4. Where only one rear fog lamp is fitted
Otherwise than above IN it must be positioned on the centre-line or offside of the vehicle.
Obligatory rear lamp has intermittent - IN operation, flickers when tapped, is affected by the operation of another lamp, does not face the rear or is incorrectly positioned
Obligatory Rear Fog Lamps (See Note 1)
Obligatory rear fog lamp insecure Detachment imminent I
Otherwise than above IN
Obligatory rear fog lamp inoperative/ (See Notes 3 and 4) IN missing/ flickers when tapped/ obscured/ incorrectly positioned/ emits light of a colour other than red/ comes on with brake light
Categorisation of Defects April 08 47
2
Section 11 Part 2: Passenger Cars, Private BusesLamps and Reflectors and Light Goods Vehicles
2
Description of Defect Severity of Defect Action Notes
Obligatory Reflectors (See Note 1)
Obligatory reflector missing/ deteriorated/ incorrectly fitted/ obscured/ insecure
Direction Indicators (See Note 1)
Direction indicator insecure
Direction indicator inoperative/ missing/ not functioning correctly/ damaged/ obscured/ wrong colour/ adversely affected by the operation of another lamp
Direction indicator warning lamp inoperative/ not fitted
Hazard Warning Lamps (See Note 1)
Hazard warning lamp inoperative/ not functioning correctly
Side Repeater Indicators (See Note 1)
Side repeater indicator inoperative/ not functioning correctly
Detachment imminent
Otherwise than above
Detachment imminent
Otherwise than above
Indicator cannot be used to clearly show the driver’s intention (See Note 5)
Otherwise than above
If the warning lamp is inoperative or not fitted and the driver cannot see that each indicator is functioning and there is no audible tell-tale device
(See Note 6)
(See Note 6)
I
IN
I
IN
I
IN
IN
IN
IN
5. The criteria must be the inability of the driver to signal intention to change direction. If remaining indicator lamps or repeaters fulfil this purpose then Inspection Notice action only will be appropriate.
6. Vehicles first used before 1 April 1986 are not required to have hazard warning lamps or side repeater indicators.
April 08 VOSA 48
Part 2: Passenger Cars, Private Buses Section 11 and Light Goods Vehicles Lamps and Reflectors
Description of Defect Severity of Defect Action Notes
Obligatory Headlamps (See Note 1)
Obligatory dipped headlamp inoperative/ dim/ missing/ obscured/ not in good working order/ flickers when tapped
Obligatory headlamp insecure or lens broken/ missing
Headlamp aim too high or too far to the right
Headlamp aim too low or too far to the left
When use of headlamps is compulsory
When use of headlamps is not compulsory (See Note 10)
Detachment imminent
Otherwise than above
Likely to cause dazzle when use of dipped headlamps is compulsory
Otherwise than above (See Notes 8 and 9)
Likely to prevent the driver from being able to drive safely when use of dipped headlamps is compulsory
Otherwise than above (See Notes 8 and 9)
I
IN
I
IN
I
IN
I
IN
7. Where a defective headlamp is part of a grouped system, consideration must be given to the capability of other headlamps in that group.
8. An immediate prohibition will normally only be appropriate for such a defect in conditions of seriously reduced visibility or at night.
9. If the degree of misalignment of the headlamp aim does not warrant an immediate prohibition, but an instrumented check shows that the headlamp aim falls outside the statutory test limits, the driver should be informed.
10. When visibility is seriously reduced (to less than 100 metres) the use of dipped headlamps is required by Regulation.
2
Categorisation of Defects April 08 49
Section 11 Part 2: Passenger Cars, Private BusesLamps and Reflectors and Light Goods Vehicles
2
Description of Defect Severity of Defect Action Notes
Obligatory Headlamps (See Note 1)
The dipped beam and/ or main beam emitted from a matched pair of obligatory headlamps cannot be switched on or off together or are not of the same colour
In any grouped obligatory headlamp system (ie more than one matched pair) they cannot either be dipped in unison or when one matched pair (the outer pair if not vertically in line) is dipped the other pair(s) are extinguished
Stop Lamps (See Note 1)
Stop lamp inoperative/ obscured/ missing/ dim/ otherwise defective in operation
Stop lamp insecure
Likely to cause dazzle when headlamp use is compulsory
Otherwise than above
Likely to cause dazzle when headlamp use is compulsory
Otherwise than above
No stop lamps show a steady red light when the brake is applied
Stop lamp(s) remain on when all brakes are released
Otherwise than above (See Note 11)
Detachment imminent
Otherwise than above
I
IN
I
IN
I
I
IN
I
IN
11. Vehicles first used before 1 January 1971 need only one stop lamp. This lamp must be fitted on the centre-line or offside of the vehicle.
April 08 VOSA 50
Part 2: Passenger Cars, Private Buses Section 11 and Light Goods Vehicles Lamps and Reflectors
Description of Defect Severity of Defect Action Notes
Reversing Lamps (See Note 1)
Reversing lamp insecure/ otherwise defective
Reversing lamp indicator inoperative
Rear Registration Plate Lamps
Not fitted/ not working/ flickers when tapped
Detachment imminent
Otherwise then above
-
-
I
IN
IN
IN
Categorisation of Defects April 08 51
2
VOSA Categorisation of Defects Contents Part 3: Motorcycles
1. ENGINE AND ASSOCIATED EQUIPMENT
Engine and Transmission Security............1
Transmission..............................................1
Oil Leaks......................................................2
Exhaust Emission........................................2
Fuel Tank and System.................................3
Exhaust System...........................................4
2. ROAD WHEELS AND TYRES
Wheels.........................................................5
Tyres............................................................6
3. SUSPENSION
Fork Assembly.............................................8
Rear Suspension.........................................8
General........................................................9
4. BRAKES
Systems.....................................................10
Performance..............................................10
Controls.....................................................10
Hydraulic Systems.....................................11
5. STEERING
Handlebars................................................14
Steering Mechanism..................................15
6. LAMPS AND REFLECTORS
Front Position Lamps.................................16
Rear Position Lamps.................................16
Reflectors ..................................................17
Direction Indicators....................................17
Headlamps.................................................17
Stop Lamps................................................18
7. FRAME AND MISCELLANEOUS PARTS
Frame........................................................19
Fairing........................................................19
Accessories...............................................19
Seat/ Footrests...........................................19
Registration Plate Details..........................19 Sidecar.......................................................20
8. ELECTRICAL EQUIPMENT
Battery........................................................21
Switchgear and Wiring...............................21 Mechanical Components...........................12 Horn...........................................................21
3
Section 1 Part 3: Motorcycles Engine and Associated Equipment
Description of Defect Severity of Defect Action Notes
Engine and Transmission Security
Engine/ gearbox mounting or frame around the mounting area fractured/ deteriorated/ corroded/ loose (See Note 1)
Transmission
Chain loose/ worn/ misaligned
Chain sprocket excessively worn/ securing bolts missing/ loose
Chain guard insecure
Drive shaft or shaft casing insecure/ drive shaft excessively worn
Engine/ gearbox detachment imminent or control of the machine likely to be affected
Otherwise than above
Failure/ detachment imminent or likely to jam the rear wheel
Otherwise than above
Failure/ detachment imminent or likely to jam the rear wheel
Otherwise than above
Failure/ detachment imminent or likely to jam the rear wheel
Otherwise than above
Failure/ detachment imminent or likely to jam the rear wheel
Otherwise than above
I
IN
I
D
I
D
I
D
I
D
1. Some machines have engines that are rubber mounted and which permit some movement at the mounting point.
Categorisation of Defects April 08 1
3
Section 1 Engine and Associated Equipment Part 3: Motorcycles
Description of Defect Severity of Defect Action Notes
Oil Leaks
Oil leak from engine/ gearbox/ drive shaft casing (See Note 2)
Exhaust Emission (See Note 3)
Engine emitting excessive exhaust smoke
Continuous flow or contaminating a tyre
Dripping giving rise to a patch in excess of 75mm diameter in 5 minutes
Otherwise than above
Sufficient to obscure vision or likely to cause danger to other road users
Continuous haze which tends to obscure vision
Continuous haze, any colour
I
D
IN
I
D
IN
2. When considering several leaks, due regard must be given to the cumulative effect which could justify prohibition action. Also, some machines have total loss engine lubrication systems or direct engine oil to the drive chain. These are acceptable.
3. Some two stroke engines produce smoke due to their design.
April 08 VOSA 2
3
Section 1 Part 3: Motorcycles Engine and Associated Equipment
Description of Defect Severity of Defect Action Notes
Fuel Tank and System
Fuel tank insecure (See Note 4)
Fuel leakage
Fuel filler cap missing/ defective
Fuel line damaged/ chafed/ insecure
Detachment imminent
Otherwise than above
Continuous leak or leak constituting a fire risk or loss of vehicle control
Otherwise than above
Such as to permit fuel spillage (See Notes 5 and 6)
Otherwise than above
Likely to fracture or leak (See Note 5)
Otherwise than above
I
D
I
D
I
IN
D
IN
4. Most fuel tanks are secured by flexible rubber mountings. Movement might not necessarily be an indication of insecurity.
5. If any fuel leak or spillage is likely to constitute a fire risk or present a hazard to other road users, an immediate prohibition must be issued.
6. Temporary caps that do not prevent spillage or the use of rags etc, in place of a fuel cap must be regarded as a defect.
Categorisation of Defects April 08 3
3
Section 1 Engine and Associated Equipment Part 3: Motorcycles
Description of Defect Severity of Defect Action Notes
Exhaust System (See note 7)
Exhaust system incomplete/ insecure / excessively deteriorated/ unsuitable type
Silencer insecure
Excessive engine exhaust noise
Detachment imminent
Otherwise than above
Detachment imminent
Otherwise than above
Does not reduce the noise emitted to a reasonable level
I
D
I
D
D
7. A silencer marked “Not for road use”, “Track use only” or similar words are unsuitable.
April 08 VOSA 4
3
Section 2 Part 3: Motorcycles Road Wheels and Tyres
Description of Defect Severity of Defect Action Notes
Wheels 1. Generally wheels distorted within the following limits can be regarded as
Wheel fractured or damaged Failure likely I acceptable
Otherwise than above D Lateral (run-out or buckling):
Loose or missing rivets or bolts in built- Failure likely I a. For a steel rim 4mm up wheels
Otherwise than above D b. For an aluminium alloy rim 2mm (cast or fabricated)
Wheel distorted/ damaged or spokes Tyre fouling other parts of the machine/ I missing or loose. An aluminium wheel directional control affected or failure likely Eccentricity: which has been repaired. (See Note 1)
For all types of rim 3mm Otherwise than above D
Excessive tightness, free play or Imminent failure likely I roughness in a wheel bearing
Otherwise than above D
Wheel misaligned or toe out, excessive Likely to seriously affect the handling or I toe-in or vertical misalignment of a steering of the machine sidecar wheel
Otherwise than above IN
Road wheel fouling Failure of the wheel or affected component I likely
Otherwise than above D
Road wheel spindle securing nut(s) or Wheel detachment likely or wheel insecure I locking device missing or loose
Otherwise than above D
Categorisation of Defects April 08 5
3
Section 2 Road Wheels and Tyres Part 3: Motorcycles
Description of Defect Severity of Defect Action Notes
Tyres
Incorrect tyres fitted (See Note 2) Likely to render the machine dangerously unstable
I
2. Examples of unsuitable tyres:
a) sidecar tyres or car tyres on a solomachine (sidecar outfits might befitted with ‘solo’ type tyres on anywheel);
Tyre fitted with ‘Direction markers’ in the wrong direction (See Note 3)
Tyre not correctly seated on the wheel rim or valve stem misaligned, insecure or damaged
Tyre has a break in the fabric or deep cut (see Note 4 and 5)
Tyre bulging (See Note 6)
Ply or cord structure exposed
Tyre seriously under inflated
-
Tyre likely to fail or suddenly deflate
Otherwise than above
Body structural cords damaged
Cut 25mm or longer exposing body cords
Caused by separation or partial failure of the structure
Due to wear on the tread area
Otherwise than above
Likely to affect the handling
Otherwise than above
D
I
IN
I
D
I
I
D
I
IN
b) motocross or similar tyres, ie tyreswhere the space between treadblocks is substantially greater thanthe size of the blocks themselves;
c) tyres designated by theirmanufacturer as unsuitable for road use eg racing tyres or those marked‘NHS’ or NOT FOR HIGHWAY USE on the side wall;
d) a tyre specifically designed for frontwheel use fitted to the rear wheel;
e) a radial ply tyre fitted to the front anda cross-ply or bias belted tyre fittedto the rear wheel;
f) a bias-belted tyre fitted to the frontwith a cross-ply tyre fitted to the rearwheel.
3. Uniquely, this does not apply toMetzeler 100/ 80 - 17 tyres fitted tothe rear wheels of Aprillia AF50 motorcycles.
4. Cuts which are deep enough to reachthe body cords but less than 25mm or10% of the section width, whichever is the greater, and have not damagedor exposed the body cords or ply donot breach the legal requirements for tyres.
April 08 VOSA 6
3
Section 2 Part 3: Motorcycles Road Wheels and Tyres
Description of Defect Severity of Defect Action Notes
Tyres
Tyre tread worn beyond the legal limit or a tyre with a recut tread
Tyre fouling against another part of the motorcycle or sidecar
The original tread pattern does not have a tread depth of at least 1mm (excluding any tie-bar or tread wear indicator) throughout a continuous circumferential band of the tread of at least ¾ of the breadth of the tread and visible tread pattern on the remainder (See Notes 7 and 8)
Tyre damaged and/ or likely to fail
Otherwise than above
I
I
IN
5. “Exposed” for this purpose means the cords are visible or it can be established that they are exposed with the use of a probe.
6. Bulging includes any lifting of the tread rubber and must not be confused with undulations.
7. Clearly the degree of non-compliance, road and weather conditions are factors that will have to be taken into account, if an exemption is to be issued.
8. If the motorcycle has an engine capacity of less than 50cc, the tread of the tyre can be less than 1mm if the tread pattern can be clearly seen over the whole tread area.
Categorisation of Defects April 08 7
3
Section 3 Suspension Part 3: Motorcycles
Description of Defect Severity of Defect Action Notes
Fork Assembly 1. Some fork arrangements rely on the bracing incorporated in the mudguard
Part of the fork assembly loose/ Failure of the component imminent and/ or I fixings to maintain their alignment. A cracked/ distorted/ misaligned/ corroded/ likely to render the machine unstable mudguard insecurely fixed to the forks excessively worn/ excessive free (See Note 1) could therefore adversely affect the play/ excessive stiffness in movement handling of the machine.
Otherwise than above D 2. Some high performance machines
Road spring broken - I are fitted with anti-dive front forks which lock when the brake is applied.
Damper inoperative or inadequate Machine likely to be unstable during braking I In these cases the front wheel will (See Notes 2 and 3) or when otherwise ridden need to be placed against a solid
object when checking the damping. Fluid leaking from a damper - IN
3. Some smaller machines are not fitted Rear Suspension with dampers on the front suspension
Suspension component which is Failure of the component imminent and/ or I loose/ cracked/ distorted/ misaligned/ likely to render the machine unstable corroded/ excessive free play/ excessive stiffness in movement
Road spring broken - I
Damper inoperative or inadequate Machine likely to be unstable during braking I or when otherwise ridden
Fluid leaking from a damper - IN
April 08 VOSA 8
3
Section 3 Part 3: Motorcycles Suspension
Description of Defect Severity of Defect Action Notes
General
Suspension so modified as to render the machine unsafe
Fouling of fixed and moving parts which restricts the movement of the suspension
Handling likely to be affected and machine unstable
Handling likely to be affected
Otherwise than above
I
I
IN
Categorisation of Defects April 08 9
3
Section 4 Brakes Part 3: Motorcycles
Description of Defect Severity of Defect Action Notes
Systems 1. Motorcycles first registered before 1 January 1927 must have a braking
The machine does not have the (See Notes 1, 2 & 3) I system that works on at least one appropriate braking system or systems wheel.
Performance 2. Motorcycles registered on or after 1 January 1927, must have an efficient
Any brake does not operate when the - I braking system with two means of relevant lever/ pedal is fully applied operation or two braking systems with
separate means of operation. Brake efficiency low (specify) Performance does not meet prescribed I
C&U requirements (See Note 4) 3. Some motorcycles have both braking systems operated from the
Performance below normal expectation IN handlebars.
Brake binding Severely overheated and failure or fire likely I 4. Where machines are tested on a roller brake tester the appropriate
Otherwise than above D Inspection Manual criteria must be used.
Brake grabbing or juddering or Such as to affect control of machine I fluctuating
Otherwise than above IN Controls
Brake lever/ pedal or mounting is loose, Failure or detachment of the lever/ pedal I cracked or the securing bolts are loose likely or missing
Brake lever/ pedal pivots worn to Brake efficiency impaired or control cannot I excess/ inoperative or so damaged, be satisfactorily applied positioned, bent or shortened that the brake cannot be readily applied/ Otherwise than above D inadequate reserve travel/ cannot be applied and released smoothly
April 08 VOSA 10
3
Section 4 Part 3: Motorcycles Brakes
Description of Defect Severity of Defect Action Notes
Hydraulic Systems
Brake master cylinder/ reservoir or caliper insecure
Brake master cylinder or caliper damaged/ incorrectly fitted/ fractured/ severely corroded/reservoir cap missing
Brake hose/ pipe damaged/ chafed/ insecure/ fouling/ trapped/ twisted/ kinked
Brake fluid level low
Brake fluid leak (specify source)
Hydraulic cylinder leaking or sponginess indicating air in system
Detached or detachment imminent
Otherwise than above
Failed or failure imminent
Otherwise than above
Failed or failure imminent
Otherwise than above
Absence of fluid in reservoir
Fluid level clearly below the minimum level indication
Otherwise than above
Obvious leak leading to brake failure or presenting risk of fire
Brake lever or pedal creeps to the stop, or obvious leak
Otherwise than above
I
D
I
D
I
D
I
D
IN
I
I
D
Categorisation of Defects April 08 11
3
Section 4 Brakes Part 3: Motorcycles
Description of Defect Severity of Defect Action Notes
Mechanical Components
Severely contaminated pad/ lining material
Any brake components excessively worn/ corroded/ fractured/ cracked/ loose (specify component)
Any brake cable or rod reduced in diameter/ excessively corroded/ frayed or knotted; a significantly damaged outer casing
Any retaining/ locking device missing/ loose (specify component)
Brake friction lining or pad missing/ excessively worn/ loose
Where contamination is clearly evident and likely to affect performance but brake test equipment not available to confirm (See Note 5)
Failed or failure imminent
Serious reduction in strength
Otherwise than above
Failed or failure imminent
Serious reduction in strength
Otherwise than above
Retaining device missing/ loose
Retaining device insecure or locking device missing or insecure
Missing, detached or braking efficiency impaired (See note 5)
Linings worn to excess
Otherwise than above
D
I
D
IN
I
D
IN
I
D
I
D
IN
April 08 VOSA 12
3
Section 4 Part 3: Motorcycles Brakes
Description of Defect Severity of Defect Action Notes
Mechanical Components
Brake drum /disc/backplate/insert loose/fractured/ excessively scored/pitted/worn or distorted
Abnormal movement of lever or pedal indicating maladjustment
Any component seized/ restricted/ fouling (specify component)
Any component forming part of an anti-lock braking system missing/ damaged/ disconnected
Likely to affect brake performance/ failed or failure imminent (See Note 6)
Otherwise than above
Likely to affect brake performance/failed or failure imminent (See Note 5)
Otherwise than above
Likely to affect brake performance
Otherwise than above
Such that the ABS system is rendered inoperative or spurious signals are given
Otherwise than above
I
D
I
D
I
D
D
IN
5. When immediate action is taken this must be reinforced with evidence that the efficiency is impaired, i.e. brake test result.
6. Some machines are fitted with discs with a limited amount of sideways float.
Categorisation of Defects April 08 13
3
Section 5 Steering Part 3: Motorcycles
Description of Defect Severity of Defect Action Notes
Handlebars
Handlebar clamps are not tight or securing bolts are loose or missing. Excessively deteriorated handlebar flexible mounting
Handlebar or fork yoke is deformed, fractured, cracked or excessively corroded
The movement of the handlebars or yoke is seriously restricted or impeded in its movement by any other part of the motorcycle
Loose handgrips
Handlebars likely to move in their mounting such that directional control could be adversely affected (See Note 1)
Otherwise than above
Failure of the handlebar or yoke likely
Likely to affect directional control
Otherwise than above
Affecting control of the machine or detachment likely
I
D
I
I
D
I
1. Handlebars on some machines are rubber mounted. Some movement might be detected when firm pressure is applied to handlebars secured in this way.
April 08 VOSA 14
3
Section 5 Part 3: Motorcycles Steering
Description of Defect Severity of Defect Action Notes
Steering Mechanism
Steering rough, notchy or stiff
Excessive free play in steering head bearings
Steering damper ineffective or defective
Likely to affect directional control of the machine
Obvious roughness
Otherwise than above
Likely to affect directional control of the machine
Restricts or impedes the operation of the steering or is likely to affect directional control of the machine
Otherwise than above
I
D
IN
I
I
D
Categorisation of Defects April 08 15
3
Section 6 Lamps and Reflectors Part 3: Motorcycles
Description of Defect Severity of Defect Action Notes
Obligatory Front Position Lamps 1. No lamps or reflectors are required to (See Note 1) be fitted to vehicles only used on
roads between sunrise and sunset. Obligatory front position lamp insecure Detachment imminent I
A front position lamp is not required Otherwise than above IN on a solo motorcycle fitted with a
headlamp. Obligatory front position lamp - IN inoperative/ missing/ dim/ obscured/ not Direction indicators are not required in good working order (See Note 1) on motorcycles which cannot exceed
25mph. Obligatory front position lamp has - IN intermittent operation, flickers when When visibility is seriously reduced tapped or does not face the front, is (to less than 100 metres), the use of affected by the operation of another dipped headlamps and side lamps is lamp required by Regulation
Obligatory Rear Position Lamps (See Note 1)
Obligatory rear lamp insecure Lamp so insecure that detachment is I imminent
Otherwise than above IN
Obligatory rear lamp inoperative/ Likely to prevent the presence of the vehicle I missing/ dim/ obscured/ not in good being indicated adequately duringworking order compulsory use
Otherwise than above IN
Obligatory rear lamp has intermittent - IN operation, flickers when tapped or doesnot face the rear, is affected by theoperation of another lamp
April 08 VOSA 16
3
Section 6 Part 3: Motorcycles Lamps and Reflectors
Description of Defect Severity of Defect Action Notes
Obligatory Reflectors (See Note 1)
Obligatory reflector missing/ deteriorated/ incorrectly fitted/ obscured/ insecure
Direction Indicators (See Note 1)
Direction indicator insecure
Direction indicator inoperative/dim/ missing/ obscured/ flickers when tapped
Direction indicator warning light inoperative/ not fitted
Obligatory Headlamps (See Note 1)
Obligatory dipped headlamp inoperative/ missing/ obscured
Detachment imminent
Otherwise than above
Detachment imminent
Otherwise than above
Indicator cannot be used to clearly show the driver’s intention (See Note 2)
Otherwise than above
The warning light is inoperative or not fitted and the driver cannot see that each indicator is functioning
When use of headlamps is compulsory
When use of headlamps is not compulsory (See Note 3)
I
IN
I
IN
I
IN
IN
I
IN
2. The criteria must be the inability of the driver to signal intention to change direction. If remaining indicator lamps or repeaters fulfil this purpose then Inspection Notice action only will be appropriate.
3. Where a defective headlamp is part of a grouped system, consideration must be given to the capability of other headlamps in that group.
Categorisation of Defects April 08 17
3
Section 6 Lamps and Reflectors Part 3: Motorcycles
Description of Defect Severity of Defect Action Notes
Headlamps (See Note 1)
Headlamp insecure/ or lens broken/ missing
Headlamp aim too high or too far to the right
Headlamp aim too low or too far to the left
The dipped beam and/ or main beam emitted from a matched pair of obligatory headlamps cannot be switched on or off together
Stop Lamps (See Note 1)
Stop lamp inoperative/obscured/ missing/ dim/ otherwisedefective in operation
Detachment imminent
Otherwise than above
Likely to cause dazzle when use of dipped headlamps is compulsory
Otherwise than above (See Notes 4 and 5)
Likely to prevent the rider from being able to ride safely when use of dipped headlamps is compulsory
Otherwise than above
Likely to cause dazzle when headlamp use is compulsory
Otherwise than above
Where required, no stop lamp shows asteady red light when the brake is applied(See Notes 6 and 7)
I
IN
I
IN
I
IN
I
IN
I
4. An immediate prohibition will normally only be appropriate for such a defect in conditions of seriously reduced visibility or at night.
5. If the degree of misalignment of the headlamp aim does not warrant an immediate prohibition, but an instrumented check shows that the headlamp aim falls outside the statutory test limits, an inspection notice should be issued.
6. Some motorcycles are not required to be fitted with stop lamps. These are as follows:
a. cannot exceed 25mph (see distinguishing plate on machines used on or after 1 August 1997).
b. was first used before 1 January 1936 or
c. was first used before 1 April 1986 which has an engine capacity of less than 50cc.
Stop lamp insecure
Stop lamp(s) remain on when all brakes arereleased
Otherwise than above
Detachment imminent
Otherwise than above
I
IN
I
IN
7. On motorcycles first used on or after 1 April 1986 the stop lamp must operate by the application of each system.
April 08 VOSA 18
3
Section 7 Part 3: Motorcycles Frame and Miscellaneous Parts
Description of Defect Severity of Defect Action Notes
Frame
Part of the frame or structure loose/ cracked/ distorted/ misaligned/ corroded or fractured
Fairing
Fairing or other bodywork item (eg mudguard) insecure
Accessories
Mirror or stands etc insecure/ fractured or damaged
Seat/ Footrests
Seat/ footrest insecure/ fractured or damaged
Registration Plate Details
Registration mark letters or numbers incorrectly formed
Failure imminent and/ or likely to make the machine unstable
Otherwise than above
Detachment or interference with directional control likely
Otherwise than above
Detachment likely or likely to impede the rotation of a wheel
Otherwise than above
Detachment likely or liable to interfere with proper control of the machine
Otherwise than above
Likely to be misread
I
D
I
IN
I
IN
I
IN
D
Categorisation of Defects April 08 19
3
Section 7 Frame and Miscellaneous Parts Part 3: Motorcycles
Description of Defect Severity of Defect Action Notes
Sidecar
Sidecar to motorcycle mountings or mounting areas corroded/ fractured/ insecure or in the case of ‘leanable’ sidecars, wear/ free play in or otherwise defective attachment of pivot joint
Detachment likely or component failure imminent which is likely to adversely affect the stability of the combination
Otherwise than above
I
D
April 08 VOSA 20
3
Section 8 Part 3: Motorcycles Electrical Equipment
Description of Defect Severity of Defect Action Notes
Battery
Battery insecure Detachment likely or displacement I constitutes risk of fire
Otherwise than above IN
Battery leaking Electrolyte likely to cause failure of items I which could affect vehicle safety
Otherwise than above IN Switchgear and Wiring
Switchgear insecure/ malfunctioning - IN
Wiring/ insecure/ inadequately insulated/ Constitutes a fire risk I or will become ineffective due to chafing or heat Otherwise than above IN
Horn
Horn missing/ insecure/ inoperative Detachment imminent I
Otherwise than above IN
Categorisation of Defects April 08 21
3
VOSA Categorisation of Defects Appendix A
Amendment Record Amendment
Number Date Date Date Amendment Number
Amendment Number
Signature andPosition
Signature andPosition
Signature andPosition
Jan1 13 2595
Sept 14 262 96
July3 15 2797
Sept4 16 2898
Aug 295 1700
Apr 306 1808
317 19
328 20
339 21
3410 22
11 23 35
3612 24
Appendix A Amendment Record
Amendment Signature and Amendment Signature and Amendment Signature andDate Date Date Number Position Number Position Number Position
37 49 61
50 6238
39 51 63
40 52 64
6541 53
6642 54
6743 55
6844 56
6945 57
7046 58
47 59 71
7248 60
Appendix BOffence Codes for the Prosecution of Offences
IM Number
Component/ System
Offence Code
Offence Category
IM Number
Component/ System
Offence Code
Offence Category
3 Seat Belts IM3 Seat belts - Not Fitted 10 Spare Wheel and Carrier IM10 Spare Wheel/ Carrier Security
5 Exhaust Emissions IM5A Emissions CO 11 Vehicle to Trailer Coupling IM11 Trailer Coupling Condition/ FunctionIM5B Emissions HC
IM5C Emissions Smoke 12 Trailer Parking Brake Emergency Brake and Airline Connections
IM12 Emergency Trailer Brake - Function
6 Road Wheels and Hubs IM6 Road Wheels Condition/ Security 13 Trailer Landing Legs IM13A Trailer Landing Legs
Security7 Size and Type of Tyres IM7 Types of Tyres IM13B Pad/ Wheel - Security
8 Condition of Tyres IM8A Condition of Tyres - 1.6mm 14 Spray Suppression, Wings
and Wheel Arches IM14 Spray Suppression
Condition/ Security IM8B Condition of Tyres
1.0mm IM14B No wing fitted
IM8C Tyres - Under Inflated 15 Cab Security IM15A Cab - Security
IM8D Tyres - Bulging IM15B Cab Wind Deflector Security
IM8E Tyres - Break/ Cut 16 Driver and Passenger Doors IM16 Vehicle Doors - Function
IM8F Tyres - Ply/ Cord Exposed 17
Driver’s Accommodation and Steps
IM17 Driver’s Step
9 Sideguards, Rear Under-run Devices and Bumper Bars
IM9A Under-run - Condition/ Security
18 Driver’s Seat IM18A(D) (Driver) Driver’s Seat Condition
IM18A(O) (Operator) Driver’s Seat ConditionIM9B Side Guard - Condition
/Security IM18B(D) (Driver) Driver’s Seat
Adjustment - Function
Categorisation of Defects April 08 B1
Appendix BOffence Codes for the Prosecution of Offences
IM Number
Component/ System
Offence Code
Offence Category
IM Number
Component/ System
Offence Code
Offence Category
18 Driver’s Seat IM18B(O) (Operator) Driver’s Seat Adjustment - Function
42 Electrical Wiring and Equipment
IM42 Condition of Electrical Wiring & Equipment
19 Security of Body IM19 Security of Body 43 Engine and Transmission IM43 Engine/ Transmission Mountings - Security
20 Condition of Body IM20 Condition of Body 44 Oil and Waste Leaks IM44 Oil/ Waste Leaks
21 Interior of Body IM21 Interior of Body Condition 45 Fuel Tanks and Systems IM45A Fuel Tank - Security
22 Driver’s Mirrors IM22A Driver’s Mirror - No View IM45B Fuel Tank - Leakage
IM22B Driver’s Mirror Security
IM45C Fuel Filler Cap Missing - Spillage
23 View to Front IM23A View to Front Obstructed
46 Exhaust Systems and PSV Waste Systems
IM46 Exhaust System - Fumes / Waste/ Security/ Fire
Glass and View of the Road IM23A Windscreen - Condition (affecting view)
48 Suspension IM48A Suspension Pins/ Bushes - Condition
IM23B Glass - Condition IM48A Road Springs - Condition
IM23C Visual transmission of light
IM48A Attachment of Spring Units - Condition
25 Windscreen Wipers and Washers
IM25 Washers/ Wipers Condition/ Function
IM48A Shock Absorbers Security
30 Steering Control IM30 Play at Steering Wheel IM48B As any of 48 above but part of Steering
34 Breaks, vacuum or pressure IM34A Presence 53 Axles, Stub Axles and Wheel
Bearings IM53A Axles Wheel Bearings
Loose or Worn warning device
IM34B Function
41 Chassis IM41 Condition of chassis IM53B As above but part of
Steering
B2 April 08 VOSA
Appendix BOffence Codes for the Prosecution of Offences
IM Number
Component/ System
Offence Code
Offence Category
IM Number
Component/ System
Offence Code
Offence Category
54 Steering Mechanism IM54 Steering Linkage Condition
IM63B Rear Lamp - Security/ Missing
IM54 Steering Gear - Condition
IM63C Headlamp(s) Inoperative/ Missing
IM54 Power Steering Condition
IM63D Headlamp(s) - Security
IM63F Stop Lamps - Function 57 Transmission IM57 Transmission - Condition
IM63G Stop Lamps - Security 58 Additional Braking Devices IM58A Additional Braking
(inc Retarders) Device - Security 66 Direction Indicators and Hazzard Warning Lamps
IM66A Indicators - Security IM58B Additional Braking
Device - Function IM66B Indicators - Function/ Missing
59 Brake Systems and Components
IM59 Mechanical Brake Components Condition/ Function
67 Aim of Headlamps IM67 Headlamps(s) - Aim
IM59 Brake Actuators Condition/ Function
71 Service Brake Performance IM71 Service Brake Performance
IM59 Braking System andComponents Condition/ Function
72 Secondary Brake Performance
IM72 Secondary Brake Performance
62 Rear Markings and Reflectors
IM62A Rear Markings Security
73 Parking Brake Performance IM73 Parking Brake performance
IM62B Reflector - Security
63 Lamps IM63A Front Position/ Outline Marker Lamp -Security
Categorisation of Defects April 08 B3
Recommended