VIBRATION SHOCK MOUNT ABSORBERS - ite-tools.com · COMPRESSOR ANCHOR TO SECURE . SOLID MEMBER...

COMPRESSOR

ANCHOR TO SECURE SOLID MEMBER

Verticalmotion

COMPRESSOR

ANCHOR TO SECURE SOLID MEMBER

Verticalmotion

Horizontalmotion

VASC Serie

VIBRATION SHOCK MOUNT ABSORBERSINSIDE CORRUGATED TUBESTAINLESS STEEL type SUS 304.

WIRE BRAIDSTAINLESS STEEL type SUS 304.

FERRULESTAINLESS STEEL type SUS 304.

CONNECTIONS• VASCseries:copperconnections• VASseries:Stainlesssteelconnections

REFRIGERANTS• AllblendedandCFC,HCFC,HFCandtheirlubricants.

TESTS• PED 97/23/EC

ATTENTION• AvibrationabsorberIS NOT ahoseoraflexiblecompensator.• Donotbenditbeforeinstallationoratanytime.Installit“in line”.

It does not eliminate any kind of unchecked vibrations but candampresidualvibrationsuncontrolledfirst.

WHY A VIBRATION ABSORBER ?Vibrationabsorbersaredesignedforinstallationinthesuctionanddischarge lineofairconditioning& refrigerationsystems todampenthe transmission of compressor-indiced vibration (if not properly ortotallyeliminatedfirst),throughsystempiping.

WHERE AND HOW IT SHOULD BE INSTALLED ?Thevibrationabsorberfunctionsbestwheninstalledasclosetothecompresssoraspossible,andperpendiculartothemajorvibrationdirectionasshowninillustration(horizontaland/orverticalmotion).Twounitscouldbeeventuallynecessary.DO NOT FORGET CORRECT ANCHOR INSTALLATION:Foroptimumvibrationabsorptionandsafety, the refrigeration lineshouldbeanchoredattheendoftheunitfurthestfromthevibrationsource(seedrawing).Care should be taken to allow sufficient space avoiding staticcompressionand/ortensionaftersoldering.“IN LINE INSTALLATION”:Unitshouldbeinstalledinastraightlineasthey are not intended to compensate for offset piping!NOTE: Thetorchsolderingflameshouldalwaysbedirectedawayfromtheferrulesofthevibrationabsorber.

SPECIFICATIONS• Vibrationabsorbersaremanufacturedof deeppitch corrugated

tubing(seenextpagedrawing) forvibrationabsorptioncoveredbyhightensilewirebraidforsuperiorstrength.Tubingandbraidare reinforcedby ferrulesateachendandareproofconnectedto female copper ODS fitting connections by high temperatureelectric oven braze alloys. The units are designed for makingsweat,quickandeasyconnectionstorefrigerantpiping.

• Operatingtemperature:-40°Cto+120°C.

1. COPPER ENDS VERSION

PART NUMBEREND O.D.S. CONNECT

(inch) A B D

Maximum workingpressure (bar)

DIMENSIONS (mm)

VASC-01VASC-02VASC-03VASC-04VASC-05VASC-06VASC-07VASC-08VASC-09VASC-10VASC-11VASC-82VASC-83VASC-84VASC-85VASC-86

1/4” 1/4” 3/8” 1/2” 5/8” 3/4” 3/4” 7/8” 11/8” 13/8” 15/8” 21/8” 25/8” 31/8” 35/8” 41/8”

6,706,709,60

12,8016,2019,2019,2022,5028,8035,3041,7054,5067,0079,6092,50

104,90

15,9015,8515,8719,0522,2228,5828,5730,1733,3536,5047,6360,3376,2088,90

101,60114,30

45454545454545454138352824221313

177,80190,50209,60228,60247,60254,00285,70292,10330,20374,60431,80508,00609,60685,80685,80838,20

(mm) A B D

DIMENSIONS (mm)

VASC-10 mmVASC-12 mmVASC-16 mmVASC-18 mmVASC-22 mmVASC-28 mmVASC-35 mmVASC-42 mmVASC-54 mm

101216182228354254

10,2012,2016,2018,3022,5028,3035,3042,5054,50

16,0019,0022,5028,5030,0033,0036,5047,5060,50

454545454541383528

210,00229,00248,00286,00292,00330,00375,00432,00508,00

NOTE:1 bar=14,5psi

NOTE:1 bar=14,5psi.

HIGH TEMPERATUREBRAZE ALLOYS

SS CORRUGATEDTUBING

WIRE BRAID

FERRULE O.D.S. END FITTINGCONNECTION

2. COMPLETE “ ITE “ STAINLESS STEEL VERSION

BRAZEJOINT

FLEXIBLETUBING

WIRE BRAID

FERRULE TUBEEND

(inch) A B D

DIMENSIONS (mm)

VAS-01VAS-03VAS-04VAS-05VAS-06VAS-08VAS-09VAS-10VAS-11VAS-82VAS-83VAS-84VAS-86

6,709,60

12,8016,2019,2022,5028,8035,3041,7054,5067,0079,60

104,90

15,9015,8719,0522,2228,5830,1733,3536,5047,6360,3376,2088,90

114,30

45454545454541383528242213

177,80209,60228,60247,60254,00292,10330,20374,60431,80508,00609,60685,80838,20

(mm) A B D

DIMENSIONS (mm)

VAS-10 mmVAS-12 mmVAS-16 mmVAS-18 mmVAS-22 mmVAS-28 mmVAS-35 mmVAS-42 mmVAS-54 mm

101216182228354254

10,2012,2016,2018,3022,5028,3035,3042,5054,50

16,0019,0022,5028,5030,0033,0036,5047,5060,50

454545454541383528

210,00229,00248,00286,00292,00330,00375,00432,00508,00

NOTE:1 bar=14,5psi

NOTE:1 bar=14,5psi.

1/4”3/8”1/2”5/8”3/4”7/8”

11/8”13/8”15/8”21/8”25/8”31/8”41/8”

VIBRATION SHOCK MOUNT ABSORBERS - ite-tools.com · COMPRESSOR ANCHOR TO SECURE . SOLID MEMBER...

Documents

PDFÑ¹ËõÆ÷pwapcgz.panasonic.cn/InfomationManager/DownLoadInfo... · 0.0 Compressor 5.0 35 0 Minisize Compressor Horizontal Compressor Vertical Compressor p contact with Panasonic

Permanently Lubricated Single Stage Vertical Portable AIR ... · Owner's Manual Permanently Lubricated Single Stage Vertical Portable AIR COMPRESSOR Model No. 919.165190 • Safety

Vertical abdominoplasty for treatment of excess abdominal ... · with a single horizontal scar. Thus, anchor or fleur-de-lis incisions, with their associated vertical and horizontal

· Web viewMeasurement Description Unit Maximum amplitude Sensor / Sensitivity 1 Compressor NDE Horizontal mm/sec RMS 5.233 Velomitor 3.94 mV/mm/s 2 Compressor NDE Vertical mm/sec

Riviera 51 Open Flybridge 51FB / 064 · • Anchor locker, access on deck. • Anchor winch vertical with overload protection circuit breaker, suit rope & chain, up & down switches

Effect of the Length of a Torpedo Anchor on Its Vertical

ROPE GRAB & VERTICAL LIFELINE (VLA)The vertical lifeline must be attached to an anchor point capable of supporting 5,000 lbs. (22.2kN) per worker or meet OSHA 1926.502 requirements

Sydenham Glass Co. · 2019. 9. 16. · Figure 2 – Vertical anchor (North American Glass) Figure 1 – Slanted anchor (North American Glass) Sydenham apparently had a fire in late

Single Anchor Vertical Lifelines and Fall Arresters€¦ · 2.1 Vertical Lifelines (VLL): VLLs are the vertical rope lifeline portion of a fall arrest or restraint system. VLLs are

Transverse, Vertical, and Antero-posterior changes … c) The TAD-anchor side of B-RME, showed greater molar crown displacement (mean 1.84 mm) than the Implant-anchor side, with statistical

CONJUGATE HEAT TRANSFER STUDY OF A CENTRIFUGAL COMPRESSOR ...€¦ · centrifugal compressor and the effects on wall temperatures and ... disk. A bladeless, vertical plate diffuser

Owner’s Manual 25 Gallon Vertical AIR COMPRESSOR

Compressor Nebulizer Compressor...nebulizer cup must remain vertical during treatment. 1. Place the compressor unit on a flat, stable surface within operating range of the patient

Single Anchor Vertical Lifelines and Fall Arresterscdn.falltech.com/pdf/instruction-manual/MVLL01 REVB... · 2018. 9. 6. · Single Anchor Vertical Lifelines and Fall Arresters User

€¦ · TECH ERECTION ANCHOR ALP2020 HD Ear Length TECH ERECTION ANCHOR DIMENSIONS Thickness —S The Tech Erection Anchor is designed for horizontal to vertical edge lifting and

For Pathways / Courtyards / Entrances · external vertical grooves align with vertical members on louver assembly. Attaches to anchor base with 4 countersunk stainless steel flat

User InstrUctIon ManUal saflok toggle anchor · PDF fileToggle Anchor (Figure 1) is a reusable anchor point for horizontal, vertical, or overhead applications. The Toggle Anchor is

OPERATING & INSTRUCTION MANUAL VERTICAL AMMONIA COMPRESSORequipment.howecorp.com/Asset/A-23_MAN.pdf · OPERATING & INSTRUCTION MANUAL VERTICAL AMMONIA COMPRESSOR BARE UNITS AW-23

VERTICAL 60 GALLON AIR COMPRESSOR...better to locate the compressor close to the power panel, and use a longer hose to reach the usage area. b. The compressor must be at least 12 inches

· Vacuum Pumps, Bore well compressor. ... Air dryer, Refrigerated / Heatless, Drive electric motor / Engine, Vertical Air receiver, This Paras Air Compressor has experience and