View
4
Download
0
Category
Preview:
Citation preview
vsupport@ventingservices.com | 1.888.750.1698
2016.04
RH901
MODEL RH90128AS / RH90134AS
30in / 36inSIZE
28-3/8in / 34-3/8inNET WIDTH
600MAX. CFM
34in28in
- custom hood liner
Today’s KitchenRANGEHOOD
390 and 290*CFM SELECTOR
6MAX. SONES
FEATURESstainless steelcolor6-speed, electronic touchcontrols(2) dual-level halogenlights(2) professional baffle / (3) professional bafflefilters
DUCT SPECS
back 3-1/4in x 10in / 8in round8in roundtop
no recirculating
*CFM selector enables the installer to limit the maximum CFM to meet local codes. When enabled, the fan speeds will be reduced as follows: 390 CFM = 3 speeds, 290 CFM = 2 speed.**install height is the distance between top of cooking surface and bottom of hood.
120v, 60hzAC INPUT
max. 480w @ 5aAC POWER
26in - 36inINSTALL HEIGHT**
28-3/8”, 34-3/8”
12”
12”
3”
22-3/8”, 28-3/8”
19-1/4”
FIG. 1
D IS C A R D T H IS P A G E A FT E R C FM C O N V E R S IO N
WHY CONTROL THE MAXIMUM BLOWER CFM?
Note: If no maximum CFM limit is enforced by your local code please disregard this instruction sheet.
PC Board
1357
2468
Jumper 5-6 or 7-8DEFAULT POSITION
Default Max. Blower CFM
Jumper 3-4Max. Blower CFM 390
Jumper 1-2
Jumper Pins
PlasticJumper
1357
2468
1357
2468
1357
2468
Before hood installation, gain access to PC board by following the steps on page 2 for your specific hood model. Take care when removing PC board as there are many wires connected to the board. Disconnecting all wires may not be necessary as long as you can easily access the jumper pins shown in FIG. 1 above.
Change plastic jumper positioning as shown in FIG. 1 to set the desired maximum blower CFM. NOTE: When CFM Selector is enabled, the number of blower speeds will be reduced as follows:
390 CFM = max. 2 speeds, 290 CFM = max. 1 speed
Re-install PC board into PC board box & continue with hood installation. To verify maximum CFM: With hood off, hold down the Power Button for 3-4 seconds.
If 3 LEDs illuminate = default max. CFM, if 2 LEDs illuminate = max. 390 CFM, and if 1 LED illuminates = max. 290 CFM
Remove the approriate foil CFM sticker included with the hood literature and place inside the hood body below the wiring diagram label or in another clearly visible location. Discard conversion sheet. See hood manual for more information such as troubleshooting and power consumption.
CAUTION:Hood must be discon-nected from main power prior to performing the conversion instructions listed below. Failure to do so could result in personal injury or damage to the product.
!
1.
2.
3.
4.
Note: PC board designs vary by model but the Jumper Pin layout is the same for all models.
1
Max. Blower CFM 290
CFM SELECTOR CONVERSION SHEET
It is recommended to always use the appropriate blower CFM to handle your cooking surface but some local codes limit themaximum amount of CFM a range hood can move. CFM Selector allows you to control the maximum blower CFM withoutthe need for expensive make up air kits. CFM Selector enables the installer to easily set the maximum blower speed to oneof two most commonly specified CFM levels; 390 or 290 CFM. Note: After the new CFM is set it cannot be reversed.
APR16.0201 1-888-750-1698
RH901: 390 CFM = max. 3 speeds, 290 CFM = max. 2 speed
RH901: If number 6 displays = default max. CFM, if 3 displays = max. 390 CFM and if number 2 displays = max. 290 CFM
D IS C A R D T H IS P A G E A FT E R C FM C O N V E R S IO N
Models: RH008- Locate PC board box on top of blower housing.
- Remove 2 to 4 screws attaching PC board cover.
Accessing PC Board Instructions
Models: RH006, RH007- Remove aluminum mesh filters.- Remove 2 to 4 screws attaching PC board cover.
2
Model: RH901
- (RH90128AS only) Remove both spacer panels by 2 screws for each spacer panel.
- Remove baffle filters and residue tray.
- Remove 5 screws attaching light panel.
- PC board located behind the light panel.Models: RH009
- Remove 2 to screws attaching switch cover.
Recommended