View
1
Download
0
Category
Preview:
Citation preview
TECH SHEET
T
E
ECH SHET
T
ET
ECH SHE
TECH SHEET
TECH SHET
E
TECH SHEET
TECH SHEET
TECH SHEET
T
E
ECH SHET
TH S
ET
ECHE
TECH SET
HE
T S
ET
ECHHE
TH S
ET
ECHE
TECH SHEET
TECH SHEET
TECH SET
HE
TEH SHEE
C
TH
TECH SEET
HEE
TECH ST
TECH SHEET
EH HEE
TC
ST
TEH SHEE
C
T
TECH SHEET
EH HEE
TC
ST
H
TECH SEET
HEE
TECH ST
EH HEE
TC
ST
HEE
TECH ST
HEE
TECH ST
EH HEE
TC
ST
TEH SHEE
C
T
EH HEE
TC
ST
T / G - 2 8 3 1 2 / 0 8
Technical Information Model GS-41 Sensortron
BLACK
1. Slide sensor coil to the right and replace plastic chip with coin or token.
TO INSTALL SAMPLECOIN OR TOKEN:
2. Release sensor coil, making sure sample coin or token is held firmly in place.
3. Do not use a 1965 or 1974 quarter as a sample.
"SENSORTRON"
lidSe
epl cR a e
C io n
To
SENSOR COILINSERT
COIN
REMOVEPLASTIC
CHIP
SENSORTRON WIRING:
NOTE: YOU MUST HAVE AT LEAST 24 VOLTSAC ACROSS BLACK AND YELLOW WIRES.
RED/GREEN WIRES ARE INTERCHANGEABLE A
234
7
"UN
IVE
RS
AL"
(4 w
ire)
RE
D/G
RE
EN
RE
D/G
RE
EN
YE
LLO
W
YE
LLO
WB
LUE
BLA
CK
BLA
CK
24 V COM
24 V HOT
GinSan24V
Timer
SENSORTRON
il eS d
p acR l e
eoiC n
oT
RED/GRN
RED/GRNYELLOW
BLACK24 VAC +
0009908
CTIVE IL TE YS
4321
COIN
0009908
"Sensortron"
li edS
l ce a eR p
C noi
To
+GS-41oN . 45219
CTIVE IL TE YS
"DC
" (3
wire
)
5. Replace rubber plug.
When using coins smaller than a quarter (in size), the coin slot opening must be made smaller to prevent jamming.
The selectivity control is designed to enable field adjustments for closer coin scrutiny, thereby providing greater rejection of slugs.
SELECTIVITYADJUSTMENTS:
Sensortrons are preset foruse with U.S. quarters.
SENSORTRONGE RR D/ N
HO S I CN TW m ap x1 a m
GE RR ND/
YE LOWL
BL CKA
+0 809900
CTIVE IL T
E Y
S
SELECTIVITY ADJUSTMENT
1. Remove black rubber plug.
REMOVEPLUG
SENSORTRONRG NR /ED
N W CHITO Sm m x1 p a a
RR /G NEDLOWYEL
L CKB A
+900 80 09
CTIVE IL T
E Y
S
2. Using small screwdriver, locate adjusting slot on potentiometer (pot.). (Slot is difficult to see in the jelly-like substance.)
4. Turn pot. counterclockwise ( a little at a time until it rejects all unwanted coins).
3. Turn pot. clockwise as far as it will go.
COUNTERCLOCKWISE
RG NR /ED
N W I CHTO Sp axm m1 a
RR /G NEDLOWYEL
L CKB A
+0900 890
CTIVE IL T
E Y
S
SHIMPLATE
P/N 74137
Problem/Symptom: Sensortron accepts unwanted slugs.Cause: In 1986 the counter weight was removed from the pendulum
damper on the Sensortron to correct isolated problems of coins sometimes jamming on the pendulum damper. Counter weights are available through customer service at GinSan Industries in Grand Rapids, MI.
Solution: Turn the silver colored counter weight with star washer clockwise
to attach in the mounting hole of the pendulum damper. (See drawing)
Selectivity Adjustments may be necessary after above procedure is
completed.
Do Not allow a coin box heater to come in contact with the Sensortron. To interface a 24 volt mechanical coin counter with a Sensortron, order a GS-17 interface, Part Number 77060.
SPECIAL INSTRUCTIONS:
PENDULUMDAMPER
COUNTERWEIGHTDo Not install Counter
Weight unless there is a problem accepting
unwanted Slugs or Coins!!!
•
•
Universal Sensortron Wiring InstructionsFor Various Timers
Note: Red/Green wires are interchangeable.GinSan Timer (GS-9 110 Volt) to Universal GS-41
Black wire to Terminal #5Yellow wire to Terminal #7Red/Green wires to Terminal #4 & #5
GinSan Timer (GS-11 110 Volt) to Universal GS-41Black wire to Terminal #4Yellow wire to Terminal #1Red/Green wires to Terminal #3 & #4
D & S Timer to Universal GS-41Black wire to 24 Hot(L1)Yellow wire to 24 Common(L2)Red/Green wires to 24 Common(L2) & Coin Terminal
Paraplate Timer to Universal GS-41Black wire to -Coin SwitchYellow wire to Jumper for 24 V ACRed/Green wires to +Coin Switch & -Coin Switch
Keltner Timer 24 Volt to Universal GS-41Black wire to Terminal #2Yellow wire to Terminal #1Red/Green wires to Terminals to #2 & #4
Parker Timer to Universal GS-41Black wire to Terminal #1Yellow wire to Terminal #3Red/Green wires to Terminals #1 & #4
Dixmor Digital Timer to Universal GS-41Black wire to 24 V AC Hot (IN)Yellow wire to 24 V AC Common (IN)Red/Green wires to Coin Common & Coin Signal
TECHNICAL SHEET 877.785.1897
3611 3 Mile Road NW Grand Rapids, MI 49534 www.GinSan.com
SEE CLEANING INSTRUCTIONS ON PAGE 2
The proper care and cleaning of a Sensortron Coin Acceptor can prevent and remedycoin rejection issues. A simple procedure is detailed below.
Place rubbing alcohol in a spray bottle.
Remove these 2 screws with a size “0” square bit,and then clean the chassis and bottom of thekicker foot with rubbing alcohol.
Remove these 3 screws, pull black boxforward slightly, and clean the back of thebox and chassis with rubbing alcohol anda cotton swab or clean cloth. Spray entirecoin path with alcohol and spray out withcompressed air
SENSORTRON CLEANING INSTRUCTIONS
IMPORTANTPlease make surethe contact point ofkicker foot andchassis isclean and dry!
T / G - 2 8 3 0 2 / 1 2
Recommended