View
254
Download
3
Category
Preview:
Citation preview
And
Syntellect IVR SIP Trunking Configuration Guide
Using AccessLine SIP Trunking
Interfacing AccessLine SIP Registrar and Syntellect SCP v8 IVR Platform
By Jeff Thorness
Introduction These Notes describe the procedures for configuring Session Initiation Protocol (SIP) Trunking between
service provider AccessLine and a Syntellect IVR system.
The AccessLine SIP Trunking service referenced within these Notes is designed for business customers.
The service enables local and long distance PSTN calling via standards-based SIP trunks directly as an
alternative to legacy analog or digital trunks, without the need for additional TDM enterprise gateways
and the associated maintenance costs.
Prerequisite for Configuring Syntellect IVR with AccessLine SIP Trunks
AccessLine Configuration Information You should have the configuration information from Accessline before you start the install. This
information will provide settings for the SIP connection(s).
The information you will receive from Accessline will be composed of the following information. Your
order will be different from this information:
• Primary codec: G.711
• Secondary codec: N/A
SIP TRUNK ID dgwsid10941
PASSWORD ********
DNS NAME usbc.accessline.com
IP ADDRESS 64.28.113.10
PORT 6060
Call processing has been setup to allow up to 2 simultaneous calls.
The following 911 callback number has been configured in our network as the
default for this location; please test and make sure you are able to present
this as the 911 callback number and program it to route appropriately on
inbound.
2065172775
This can also be used for testing inbound calls and has been setup as the
default for outbound CLI. The following additional test number has also been
provisioned.
2065172789
Set Up Instructions:
1) Within the Syntellect Console, drill down to the “Dialogic Boards Driver” and under “HMP Startup Options” set the following:
a. IP Address: {value of the IP address for your IVR (ECS) } b. SIP Port: “6060” c. Max # of IP Calls: {qty of licensed HMP ports} d. Optionally-> reserve some of those IP resources for outbound e. Detect DTMF over SIP: “No”
2) Click on the last HMP board definition (the one labeled “HMP (IP)” and set the following values: a. Global Call IP protocol: “SIP” b. Fast Start and Fast Answer can both be either Yes or No – Yes by default c. DTMF Transmission mode: “RFC_2833” d. Codec 1 type: “G.711 u-Law”
3) Click on the “SIP Digest Authentication” and set the following values: a. Realm: “accessline” b. Identity: “sip:”+ {SIP TRUNK ID} +”@64.28.113.10” <- IP address of Registrar c. Username: {SIP TRUNK ID} d. Password: {Password}
4) Drill down on Registration to SIP and then add a domain by right clicking on the right hand side of the screen and then choose Add from the menu. Options:
a. Realm/Domain: {IP Address of Registrar} +”:6060” in order to use port 6060 b. Registration interval: 60 <- This keeps the link alive by re-registering once per minute c. Accept other defaults for hops and register users
5) Drill down on SIP and then the real/domain that you just created and then click on Users. From there, right click on the right hand side of the screen and “Add” a user using the following parms:
a. Address: {SIP Trunk ID}+”@64.28.113.10” < - Registrar’s IP Address b. Contact: {SIP Trunk ID}+”@”+{your ECS IP Address} c. Register: Yes
Once you have all these values set, you should be able to restart your CP Engine and accept phone calls. If you want to make outbound SIP calls, continue on ….
1) Within your script, you must set your @CallingParty system variable in order to authenticate yourself with your registrar before making a call. Failure to set this value correctly will result in a 407 proxy authentication failure and the call will not initiate.
a. @CallingParty: “sip:”+{SIP TRUNK ID}+”@64.28.113.10” <-Registrar’s IP Address
2) In the Make a Call dialogue, use SIP notation for the dial string:
a. “sip:”+{phone# to dial}+”@64.28.113.10:6060” <- IP address of Registrar and Port 6060
Fax Line(s) Setup FAXing is not supported by the Syntellect IVR system.
Emergency (911) Hunt Group
AccessLine configures a unique 911 callback number per customer location. The 911 callback number is
registered with our E911 provider. When AccessLine receive a 911 call from the PBX, we forward the
call to our E911 provider with the registered 911 callback number as the CLI (regardless of what was
passed from the PBX). The 911 callback number is used by the Emergency responders to call back to the
location.
Recommended