View
217
Download
4
Category
Preview:
Citation preview
• Very good bonding strength.
• Flexible.
COVERAGE• A 20 Kg. bag of DAVCO SUPER TTB
covers 4 - 5 sq.m. depending ontile size and weight, substratesand bed thickness.
PACKAGING• 20 kg. bag
STORAGE•
60 x 60 cm. and Up No slip Excellent Bonding
20 Kg. bag of DAVCO STTB covers approximately 4 - 5 sq.m.
SUPER TTB DUSTLESS
A high quality tile adhesive, with added polymers. The Dustless technology
reduces dust by 80% compared to a normal tile adhesive and is specially
formulated to provide healthier working conditions.
CHARACTERISTICS
DESCRIPTION
USES
COVERAGE
• Tile on wall and floor.
• Interior/Exterior.
• Large tiles and low porous tiles 60x60 cm. and more.
• Substrates: cement, mortar.
CEMENT BASED TILE ADHESIVE
| ENGLISH VERSION 10/60 1 |
Tile Adhesive
Size of Trowel Coverage Size of Tile
4x4 mm. 12.5 sq.m.
6x6 mm. 7.5 sq.m.
Mosaic or Small TileUp to 10x10 cm.
Medium TileUp to 30x30 cm.
10x10 mm. 5.6 sq.m.
12x12 mm. 4.6 sq.m.
Big Tile, Thick Bed ApplicationMore than 30x30 cm.
Big Tile, Thick Bed ApplicationMore than 30x30 cm.
**Actual filed performance will depend on installation and site condition.
1 year from date of manufactureif stored in unopened originalpackaging in dry condition.
Bulk Density (Kg./L.) : 1.2-1.3
Open Time at 20°C (min.) : 25-30
Adjustement time 25°C (min.) : 25-30
Pot life at 21°C (Hours) : 180-240
Bedding (mm.) : 1.5-6
Sag Test (mm.) : Nil
Open time bonding after 20 min
at 28 days (MPa) : >0.5
Application1. Use a proper notched trowel to spread the adhesive
onto the substrate with the flat side of the trowel
until it is smooth.
2. Use the notched side of the trowel to create an
even adhesive bed. minimum bed thickness is
- 2 mm. for wall.
- 3 mm. for floor.
(size depends on the thickness of tiles).
3. Ensure the adhesive is wet when the tiles are laid
and tapped into the position to ensure full contact
with the adhesive. Do not spread more than 1 sq.m.
at once.
4. Once the tiles have been laid, leave to stand for 24
hours or the tile adhesive is dry before grouting
with Davco Tile Grout.
• Temperature range for use : 5oC to 35oC.
• Do not add additional water or powder after slaking period.
• This is a professional product, all directions must be
followed strictly.
PRECAUTIONSWORK INSTRUCTIONS
1. Slowly add DAVCO STTB 20 kg. to a bucket of
clean water (mixing ratio for 20 Kg. bag: 4-4.5 Litres
of water).
2. Use power drill to mix until a thick creamy consistency
is achieved.
3. Allow the mixture to stand for 1 - 3 minutes for
chemical slaking and reducing air bubble, then remix
before using the adhesive.
Product preparation
Surface preparation 1. Surface must be clean and without any trace of oil.
2. Painted surface must be abreded to expose at least
80% of the original substrate.
3. New concrete must be allowed to cure for at least
28 days.
4. New render must be allowed to cure for at least
7 days.
SPECIFICATIONS
EvaluationAdhesion Test
Adhesion strength (MPa)
Tensile adhesion strength after water immersion (MPa)
Tensile adhesion strength after heat aging (MPa)
>1
>1
>0.5
2 |
094 551 5458 02 651 8003 parexgroup.co.th e-learning VDO
*The information provided in this document results from our knowledge of the products and our experience. On-site results may vary, in particular according to the product application methods adopted. Where application methods not representative test before using the products. The above-mentioned information in no way constitutes a warranty relative to the use of the products. Our general terms and conditions of sale shall prevail, in any event, on the information provided in this document. Prior to application, customers and users are requested to check that they have the lasted version of this document.
ParexGroup Company Limited. 183 Regent House Building, Rajdamri Road., Lumpini, Bangkok 10330
| ENGLISH VERSION 10/60
Recommended