View
2
Download
0
Category
Preview:
Citation preview
Always wear clean latex or cotton gloves when handling the mounting mechanism. Cut-resistant gloves are recommended for handling metal reflectors. Marks left on the reflector will reduce light output and cause damage not covered by the manufacturer’s warranty.
Round fixed model shown
Push fixing ring down on the bezel and twist ¼ turn to remove heatsink and optic.
TIR Optic Lens InstallationXN, VN and NS optics (LCRN and LCRS)
NSR and NSFR Optic Installation (LCRS only)
Reflector Optic Lens InstallationN, NR and NFR optics (LCRS only)
M, MFR, W, WFR, VW, VWFR and DAS optics (LCRN and LCRS)
Locate the fixing ring to the bezel using identifcation
markers and push the fixing ring down and twist to lock
CHANGE OPTIC (CONSULT BEZEL SECTION TO REMOVE/REPLACE BEZEL):
=
INTERCHANGEABLE OPTICS GROUPS
Hold fixture heatsink up to avoid dropping optical accessory(ies).
NOTICE Make sure to insert TIR optic or metallic reflector in the 3 channels
of the the LED connector.
NOTICE
NOTICE
1 Replace optic2 Replace bezel or adjustable mechanism(Refer to Change bezel section for instructions).
3
Fixingring Optical
accessory(ies)
Bezel or adjustable mechanism 1
2
1
2
3
4
DO NOT CONNECT OR DISCONNECT FIXTURE UNDER LOAD
REFER TO INSTALLATION INSTRUCTIONS DOCUMENTS FORPRODUCTS INSTALLATION STEPS OR WIRING DETAILS. !
Do not install silicone disk if already present from original optic.
!
AWWTrue asymmetric
wallwash kit
Optics within the same group can be swapped, some restrictions may apply. Please consult factory for any optical modification to your product.
Recommended installation:
Place matteside toward LEDPlace matte
side toward LED
LED
*Replacement silicone disk sold separately: LCROP000001
LED
Only available with standard bezel.[1]
LCRNOP000001 LCRSOP000001
Ordering code example:
NANO SMALL
LCRN - Lumencore Nano (Group 1)
NS15°
N25°
XN5°
VN10°
XN5°
VN10°
NFR25°
M40°
MFR40°
W60°
WFR60°
VW80°
VWFR80°
LCRS - Lumencore Small (Group 1)
LCRN - Lumencore Nano (Group 2) LCRS - Lumencore Small (Group 2)
LCRN - Lumencore NanoNo interchangeable optic available with XN, VN, AWW and DAS optics.
LCRS - Lumencore SmallNo interchangeable optic available with XN, VN, AWW and DAS optics.
NS15°
NSR15°
NSFR15°
N25°
NFR25°
NR25°
M40°
MFR40°
W60°
WFR60°
VW80°
VWFR80°
WWAccent wallwash
* *
* *
* *
*
*
*
*
*
* *
*
WWAccent wallwash
[1] [1]
DASDouble asymmetric
wallwash kit*
AWWTrue asymmetric
wallwash kit
DASDouble asymmetric
wallwash kit*
LCRN - Lumencore NanoLCRS - Lumencore Small
1220 Marie-Victorin Blvd., Longueuil, QC J4G 2H9 CA 1.877.937.3003 P. 514.937.3003 F. 514.937.6289info@lumenpulse.com www.lumenpulse.comCopyright © Lumenpulse Group Inc. 2019
Confidential and proprietary
Lumenpulse Group Inc. reserves the right to make changes to this product and related instructions at any time without prior notice and such changes shall be effective immediately. See www.lumenpulse.com/support/downloads for current data and instructions.2019.10.21
MS - R1
p.1/4
drawing number 145105
SPARE PARTS GUIDE lumencore™
All complete fixtures need to have maching type labels.
Type labels are yellow on fixture.
NOTICE
=A A
Screw the trim onto ceiling with a screwdriver.
Finish ceiling before install LUM CORE.
MAX. #10 Drywall screws (by others)
TRIM
1 2 3
4X
Fixed Downlight / Shower Rated / Pinhole Fixtures Fixed Tilt / Adjustable / Wallwash Fixtures
CHANGE BEZEL:
CHANGE TRIM:
CONTROL - REPLACEMENT DRIVER
DECORATIVE BEZEL
Remove bezel 1 Change accessory in the adjustable mechanical accessory clip and replace bezel.
2Replace new bezel.2
Locate the fixing ring to the bezel using identifcation
markers and push the fixing ring down and twist to lock
Align bezel and ceiling mounting
ring notches.
Adjustable mechanical accessory clip
Accessory
Bezel
Remove bezel 1
Roundbezel
Squarebezel
SB - Standard MB - Mid/semi recess DB - Deep recess DR - Deep rolled over T - Fixed tilt PB - PinholeADB - Adjustable
Trim holds up with magnets.
NOTICE
« click »
With trim Trimless
MTG: LCRN-DRV-L20-22K-80-NFR-NO-RM
LUM CORE: LCRN-DRV-L20-22K-80-NFR-NO-RM
Round Trim Square Trim
PB - Pinhole PB - PinholeSB - Standard MB - Mid/semi recess
DB - Deep recess
ADB - Adjustable T - Fixed tilt
SB - Standard MB - Mid/semi recess
DB - Deep recess
ADB - AdjustableT - Fixed tilt
Always wear clean latex or cotton gloves when handling the mounting mechanism. Cut-resistant gloves are recommended for handling metal reflectors. Marks left on the reflector will reduce light output and cause damage not covered by the manufacturer’s warranty.
DO NOT CONNECT OR DISCONNECT FIXTURE UNDER LOAD
REFER TO INSTALLATION INSTRUCTIONS DOCUMENTS FORPRODUCTS INSTALLATION STEPS OR WIRING DETAILS. !
Mud ring may require hole to be
drilled depending on ceiling thickness and
length of screws.
NOTICE
Clip the trimless mud ring on the ceiling mounting ring.
FD - DownlightWA - Wallwash
FD - Downlight FD - Downlight FD - DownlightSH - Shower
AD - Adjustable WA - WallwashFT - Fixed tilt
P - Pinhole
To order a Shower fixture please refer to Shower Rated IP55 kit in the Quick Swap Kit section.
Available bezel finishes: MWH, MBK, NKS, DCH, BCH, SWT, CC or SP
Compatible fixtures
[2] To order a Wallwash fixture please refer to Accent wallwash, True asymmetric wallwash or Double asymmetric wallwash kits in the Quick Swap Kit section. [3]
[1]
[1]
[1]LCRN-BZ-R-SB-(XXX)LCRS-BZ-R-SB-(XXX)
LCRN-BZ-S-SB-(XXX)
LCRS-BZ-S-SB-(XXX)
LCRN-BZ-R-MB-(XXX)LCRS-BZ-R-MB-(XXX)
LCRN-BZ-S-MB-(XXX)
LCRS-BZ-S-MB-(XXX)
LCRN-BZ-R-DB-(XXX)LCRS-BZ-R-DB-(XXX)
LCRN-BZ-S-DB-(XXX)LCRS-BZ-S-DB-(XXX)
LCRN-BZ-R-DR-(XXX)LCRS-BZ-R-DR-(XXX)
LCRN-BZ-S-DR-(XXX)LCRS-BZ-S-DR-(XXX)
LCRN-BZ-R-AD-(XXX)LCRS-BZ-R-AD-(XXX)
LCRN-BZ-S-AD-(XXX)LCRS-BZ-S-AD-(XXX)
LCRN-BZ-R-FT-(XXX)LCRS-BZ-R-FT-(XXX)
LCRN-BZ-S-FT-(XXX)LCRS-BZ-S-FT-(XXX)
LCRN-BZ-R-P-(XXX)LCRS-BZ-R-P-(XXX)
LCRN-BZ-S-P-(XXX)LCRS-BZ-S-P-(XXX)
[1]
[1]
[1]
[1]
[1]
[3]
[1]
[1]
[1]
[1]
[1]
[1]
[2]
Compatibl bezels
Available trim finishes: MWH, MBK, NKS, CC or SP[1]
TLR - Trimless round
LCRN-TRM-TRL-(XXX)LCRS-TRM-TRL-(XXX)
RD - Round
LCRN-TRM-RD-(XXX)LCRS-TRM-RD-(XXX)
[1]
[1]
SR - Square trim with round hole
LCRN-TRM-SR-(XXX)LCRS-TRM-SR-(XXX)
[1]
[1]
PR - Pinhole round PSR - Pinhole square trim with round hole
PS - Pinhole squareSQ - Square
LCRN-TRM-SQ-(XXX)LCRS-TRM-SQ-(XXX)
[1]
[1]
TLS - Trimless square
LCRN-TRM-TRS-(XXX)LCRS-TRM-TRS-(XXX)
[2]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
[1]
trim with round hole
T Fixed tilt
LCRN-BZ-R-FT-(XXX) [
LCRN-BZ-S-FT-(XXX) [1
LCRN-TRM-PR-(XXX)LCRS-TRM-PR-(XXX)
[1]
[1]LCRN-TRM-PSR-(XXX)LCRS-TRM-PSR(XXX)
[1]
[1]LCRN-TRM-PS-(XXX)LCRS-TRM-PS-(XXX)
[1]
[1]
LCRNOP000001 LCRSOP000001
Ordering code example:
NANO SMALL
Ordering code example:
LCRN - Lumencore NanoLCRS - Lumencore Small
1220 Marie-Victorin Blvd., Longueuil, QC J4G 2H9 CA 1.877.937.3003 P. 514.937.3003 F. 514.937.6289info@lumenpulse.com www.lumenpulse.comCopyright © Lumenpulse Group Inc. 2019
Confidential and proprietary
Lumenpulse Group Inc. reserves the right to make changes to this product and related instructions at any time without prior notice and such changes shall be effective immediately. See www.lumenpulse.com/support/downloads for current data and instructions.
drawing number 145105
SPARE PARTS GUIDE lumencore™
2019.10.21MS - R1
p.2/4
Make sure springs fit ceiling thickness.
NOTICE
0.04" to 1"[1mm to 25mm]ceiling thickness
0.04" to 1"[1mm to 25mm]ceiling thickness
1.05" to 2" [27mm to 51mm] ceiling thickness
CEILING MOUNTING RING
Fixed Downlight / Shower Rated / Pinhole Fixtures Fixed Tilt / Adjustable Fixtures
CHANGE OPTICAL ACCESSORIES:
ACCESSORIES
Heatsink
Optic (consult Optics Interchangeability Reference Guide for more details).
Optical accessory can be combined in the fixture (field changeable);- Fixed: up to two optical accessories- Pinhole: up to two optical accessories- Shower rated: one optical accessory
Decorative bezel (consult specification sheet for bezel options)
Heatsink
Optic (consult Optics Interchangeability Reference Guide for more details).
Optical accessory (field changeable)
Adjustable mechanism
Adjustable mechanism accessories clip
Optical accessory (field changeable)
Decorative bezel (consult specification sheet for bezel options)Place optical
accessory on the adjustable mechanism accessory clip.
Refer to Change Optic section for
instructions to access optical accessories.
Refer to Change optic section forinstructions to access optical accessories.
Refer to Change bezel section for instructions to access optical accessories.
Opticposition
accessory
Bezelposition
accessory
Opticposition
accessories
1 Clip on bezel
Arrow must be aligned on top of fixed tilt bezel
2
Optical accessory(ies)
Bezel
Optical accessory
Adjustable mechanism
« click »
CL - Clear glass lens
SL - Softening glass lens
PD - Prismatic diffuser
XLVR - Concentric ring louver
Beam Distribution(field adjustable)
40°
1°
Beam Distribution(field adjustable)
60°
1°
HL - Honeycomb louver
LSN - Linear spread lens narrow 1° x 40°
LSW - Linear spread lens wide 1° x 60°
Ceiling Mounting Ring Accessories Kits Remplacement Mounting Arms
2X Philips #1
Always wear clean latex or cotton gloves when handling the mounting mechanism. Cut-resistant gloves are recommended for handling metal reflectors. Marks left on the reflector will reduce light output and cause damage not covered by the manufacturer’s warranty.
DO NOT CONNECT OR DISCONNECT FIXTURE UNDER LOAD
REFER TO INSTALLATION INSTRUCTIONS DOCUMENTS FORPRODUCTS INSTALLATION STEPS OR WIRING DETAILS. !
NOTICE
FD - DownlightAD - AdjustableFT - Fixed tiltSH - ShowerP - Pinhole
FD - DownlightAD - AdjustableFT - Fixed tiltP - Pinhole
FD - DownlightAD - AdjustableFT - Fixed tiltP - Pinhole
FD - DownlightAD - AdjustableFT - Fixed tiltSH - ShowerP - Pinhole
FD - DownlightAD - AdjustableFT - Fixed tiltSH - ShowerP - Pinhole
FD - DownlightAD - AdjustableFT - Fixed tiltSH - ShowerP - Pinhole
Compatible fixtures
Place matteside toward LED
LCRNACC00003LCRSACC00003
LCRNACC00010LCRSACC00010
LCRNACC00001LCRSACC00001
LCRNACC00002LCRSACC00002
LCRSCR000004LCRNCR000004
WET installationRound
Standard installationRound
SquareSquare
LCRSCR000002LCRNCR000002
LCRSCR000006LCRNCR000006
LCRSCR000008LCRNCR000008
LCRSCR000003LCRNCR000003
WET installationRound
Standard installationRound
SquareSquare
LCRSCR000001LCRNCR000001
LCRSCR000005LCRNCR000005
LCRSCR000007LCRNCR000007
LCRSSP000001
1.05" to 2" [27mm to 51mm] ceiling thickness
LCRSSP000002LCRNSP000002
LCRNSP000001
LCRNACC00004LCRSACC00004
LCRNACC00005LCRSACC00005
LCRNACC00006LCRSACC00006
DETAIL VIEW
Notch x1
DETAIL VIEW
Notches x2
DETAIL VIEW
Notches x3
BW1 - Beam widening lens (+10°)
BW2 - Beam widening lens (+20°)
BW3 - Beam widening lens (+30°)
FD - DownlightAD - AdjustableFT - Fixed tiltSH - ShowerP - Pinhole
LCRNACC00007LCRSACC00007
LCRNACC00008LCRSACC00008
LCRNACC00009LCRSACC00009
DETAIL VIEW
Notches x1
DETAIL VIEW
Notches x2
Consult specification sheets for suggested positioning of optical accessories. [1]
LCRNOP000001 LCRSOP000001
Ordering code example:
NANO SMALL
[1]
LCRN - Lumencore NanoLCRS - Lumencore Small
1220 Marie-Victorin Blvd., Longueuil, QC J4G 2H9 CA 1.877.937.3003 P. 514.937.3003 F. 514.937.6289info@lumenpulse.com www.lumenpulse.comCopyright © Lumenpulse Group Inc. 2019
Confidential and proprietary
Lumenpulse Group Inc. reserves the right to make changes to this product and related instructions at any time without prior notice and such changes shall be effective immediately. See www.lumenpulse.com/support/downloads for current data and instructions.
drawing number 145105
SPARE PARTS GUIDE lumencore™
2019.10.21MS - R1
p.3/4
CHANGE ADJUSTABLE MECHANISM ON LUM CORE:
QUICK SWAP KITS
ADJUSTABLE COMPONENTS
Heatsink springs
Adjustable mechanical
Bezel
Optical accessory (field changeable)
Optical accessory (field changeable)
DAS - Double asymmetric wallwash kit
SH - Shower rated IP55 bezel kit(dead front)
WET - WET IP54 kit (fixed Lumencore only)
AWW - True asymmetric wallwash kit
DAS - Double asymmetric wallwash kitWW - Accent wallwash kit
WW - Accent wallwash kit
NSFR - Narrow spot faceted reflectorNSR - Narrow spot reflector
AWW - True asymmetric wallwash kit
SH - Shower rated IP55 bezel kit(dead front)
WET - WET kit IP54 (fixed Lumencore only)
FT - Adjustable mechanism (Fixed tilt fixture) CLIP - Adjustable mechanism accessory clipAD - Adjustable mechanism (Adjustable fixture)
Round fixed model shown
=
Hold fixture heatsink up to avoid dropping optical accessory(ies).
NOTICE
Attach springs to top hook and pull down.
Attach springs to bottom hook.
Fixingring
Locate the fixing ring to the bezel using identifcation
markers and push the fixing ring down and twist to lock
21
Push fixing ring down on the bezel and twist ¼ turn to remove heatsink and optic.
1 2 Replace adjustable mechanism on LUM CORE.3Recover bezel and accessory(ies) from original fixture to install on new adjustable mechanism.
12
Accessory clip
Always wear clean latex or cotton gloves when handling the mounting mechanism. Cut-resistant gloves are recommended for handling metal reflectors. Marks left on the reflector will reduce light output and cause damage not covered by the manufacturer’s warranty.
DO NOT CONNECT OR DISCONNECT FIXTURE UNDER LOAD
REFER TO INSTALLATION INSTRUCTIONS DOCUMENTS FORPRODUCTS INSTALLATION STEPS OR WIRING DETAILS. !
LCRN - Lumencore Nano
LCRS - Lumencore Small
LCRN-REP-WW--(XX..) LCRN-REP-AWW--(XX..) LCRN-REP-DAS--(XX..) LCRN-REP-SH--(XX..) LCRN-REP-WET
LCRS-REP-WW--(XX..) LCRS-REP-AWW--(XX..) LCRS-REP-SH--(XX..) LCRS-REP-WET
LCRNAM000001LCRSAM000001
LCRNAM000002LCRSAM000002
LCRCSP000001
LCRNACC00011LCRSACC00011
- NS TIR optic- WW lens- Accessory clip for WW lens- Fixed tilt bezel - Adjustable m echanism
- NS TIR optic- AWW diffuser film - AWW lens- Standard bezel - Half snoot
- Outer reflector- Inner reflector- Standard bezel
LCRS-REP-DAS--(XX..)
- Outer reflector- Inner reflector- Standard bezel
- Shower rated plastic bezel (dead front) - Ceiling ring with installed gasket
- Clear glass lens- Ceiling ring with installed gasket
- Shower rated plastic bezel (dead front) - Ceiling ring with installed gasket
- Clear glass lens- Ceiling ring with installed gasket
NOTICE
An accessory clip is needed to add optical
accessories to adjustable and fixed tilt bezel.
- N TIR optic- WW lens- Accessory clip for WW lens- Fixed tilt bezel
- NS TIR optic- AWW lens- Standard bezel - Half snoot
Available bezel finishes: MWH, MBK, NKS, DCH, BCH, SWT, CC or SP[1]
Available bezel finishes: MWH or MBK[2]
Available cutout: R or S[3]
[1][3][1][3]
[1][3]
[1][3]
[1][3]
[1][3]
[1][3]
[1][3]
[2][3]
LCRS-REP-NSR-(XX..) LCRS-REP-NSFR-(XX..)
- NS TIR optic- Semi-specular secondary reflector- Standard bezel
- NS TIR optic- Specular faceted secondary reflector- Standard bezel
[2][3] [3]
[3]
LCRNOP000001 LCRSOP000001
Ordering code example:
NANO SMALL
1 2
LCRN - Lumencore NanoLCRS - Lumencore Small
1220 Marie-Victorin Blvd., Longueuil, QC J4G 2H9 CA 1.877.937.3003 P. 514.937.3003 F. 514.937.6289info@lumenpulse.com www.lumenpulse.comCopyright © Lumenpulse Group Inc. 2019
Confidential and proprietary
Lumenpulse Group Inc. reserves the right to make changes to this product and related instructions at any time without prior notice and such changes shall be effective immediately. See www.lumenpulse.com/support/downloads for current data and instructions.
drawing number 145105
SPARE PARTS GUIDE lumencore™
2019.10.21MS - R1
p.4/4
Recommended