View
0
Download
0
Category
Preview:
Citation preview
Sony CorporationHome Entertainment Business Group
SERVICE MANUAL
9-890-762-11
2011H6900-1© 2011.08
Published by Design Engineering Dept.
BLU-RAY DISC / DVD PLAYER
BDP-BX18/S185/S186RMT-B118A/B118P/B109C
SPECIFICATIONS
SystemLaser: Semiconductor laser
Inputs and outputs(Jack name:
Jack type/Output level/Load impedance)
HDMI OUT:HDMI 19-pin standard connector
LINE OUT VIDEO:Phono jack/1.0 Vp-p/75 ohms
LAN (100):100BASE-TX Terminal
USB:USB jack Type A maximum current 500mA
GeneralPower requirements:
120V AC, 60Hz (BDP-S185:US, CND/BX18)220 – 240V AC, 50/60Hz (AEP,UK, AUS,RUS,CN)
Power consumption:10 W
Dimensions (approx.):290mm × 188mm × 42.5mm(width/depth/height) incl. projecting parts
Mass (approx.): 1.1kg
Operating temperature:5 ºC to 35 ºC(41 F to 95 F)
Operating humidity:25 % to 80 %
Supplied accessories
Specifications and design are subject to change without notice.
Audio/video cable (phono plug ×3) (1)(AUS,RUS,US,CND)
Remote commander (remote) (1) Size AA (R6) batteries (2)
Photo: BDP-S185Remote : RMT-B118A
HDMI cable (1) (BDP-S185:CN/BX18)
(BDP-S185:US/BX18:US)
ENERGY STAR and the ENERGY STAR mark are registered U.S. marks. ENERGY STAR is a registered mark owned by the U.S. government.
US ModelCanadian Model
Australian/NZ Model Chinese Model
Russian Model
AEP Model
UK Model
LINE OUT R-AUDIO-L:Phone jack/2 Vrms/10 kilohms
DIGITAL OUT (COAXIAL):Phono jack/0.5 Vp-p/75 ohms
BDP-S185
BDP-S185/BX18
BDP-S185/S186
º º
TM
Ver. 1.0 2011.08
(For connecting a USB device)
– 2 –
SAFETY CHECK-OUT
LEAKAGE TESTThe AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods.1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers' instructions to use these instruments.
2. A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication is 0.75V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A)
1. Check
the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges.
2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.
5. Check the line cord for cracks and abrasion. Recommend the replacement of any such line cord to the customer.
6. Check the B+ voltage to see it is at the values specified.7. Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage. Check leakage as described below.
After correcting the original service problem, perform the following safety checks before releasing the set to the customer:
1.5kΩ0.15µF(0.75 V)
Parts on Set
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
Unleaded solderBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
: LEAD FREE MARKUnleaded solder has the following characteristics. Unleaded solder melts at a temperature about 40°C higher than
ordinary solder. Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to
about 350°C. Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful! Strong viscosity Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.
Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
CAUTION:The use of optical instrument with this product will increase eye hazard.
CAUTIONUse of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radia-tion exposure.
This label is located on the laser protective housing inside the enclosure.
WARNING!!WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION, BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 25 cm FROM THE SURFACE OF THE OBJEC-TIVE LENS ON THE OPTICAL PICK-UP BLOCK.
For customers in European countries
product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK OR DOTTED LINE WITHMARK ON THE SCHEMATIC DIAGRAMS AND IN THE PARTSLIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESECOMPONENTS WITH SONY PARTS WHOSE PARTNUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLE-MENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE SUR LESDIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONTCRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NEREMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONYDONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OUDANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
BDP-BX18/S185/S186
– 3 –
TABLE OF CONTENTS
1. SERVICE NOTE
1-1. Disc Removal Procedure If The Tray Cannot Be Ejected (Forced Ejection) ............................................. 1-11-2. Work when optical device are replaced ........................ 1-11-3. Test Disc ....................................................................... 1-2 1-3-1. Operation and Display ............................................. 1-2
1-4. Drive Repairing............................................................. 1-15 1-4-1. Preparation .............................................................. 1-15 1-4-2. Checking Flow ~ Drive (BU) section ~ .................... 1-15 1-4-3. BU Check Flow [zz] ~ .............................................. 1-16 1-4-4. BU (Optical Block) Repair Guide ............................. 1-16 1-4-5. BU Adjustment Flow [yy] ~ ...................................... 1-17 1-4-6. KEM-470AAA/C2RP Packing Spec. ....................... 1-17 1-4-7. KEM-470AAA/C2RP Packing .................................. 1-18 1-4-8. BU Data Decode Jig ................................................ 1-19 1-4-9. Loading For Service ......................................... 1-20 1-4-10. Laser Caution Label ................................................ 1-20
2. DISASSEMBLY
2-1. Disassembly Flow ........................................................ 2-12-2. ......................................................... 2-12-3.
Tray Cover Assy
.......................................................... 2-22-4. FR-316 Board, Switching Regulator.............................. 2-42-5.
MB-143 Board............................................................... 2-4
2-6. 2-52-7. ................................................................... 2-52-8. ........................................... .. 2-6E
3. BLOCK DIAGRAMS
3-1. Overall Block Diagram.................................................. 3-13-2. DSP Block Diagram ...................................................... 3-23-3. AV OUT Block Diagram ................................................ 3-33-4. USB/ETHER, Block Diagram .................................. 3-43-5. Power Block Diagram .......................................... 3-5E
4. SCHEMATIC DIAGRAMS
4-1. This Note Is Common For Schematic Diagrams .......... 4-14-2. Frame Schematic Diagram........................................... 4-24-3. FR-316 Board (FRONT LEFT) Schematic Diagram ... 4-34-4. FR-316 Board (USB FRONT) Schematic Diagram ...... 4-4
4-6.
MB-143 Board (DDR 3 A)
Schematic Diagram (1/14)............................................ 4-5
4-7.
MB-143 Board (DDR 3 B)
Schematic Diagram (2/14)............................................ 4-6
4-13. MB-143 Board (AUDIO) Schematic Diagram (9/14)............................................ 4-134-14. MB-143 Board (VIDEO) Schematic Diagram (10/14).......................................... 4-144-15. MB-143 Board (GPIO/JTAG) Schematic Diagram (11/14) .......................................... 4-154-16. MB-143 Board (IF CON) Schematic Diagram (12/14).......................................... 4-164-17. MB-143 Board (FE_POWER/OP/GIO) Schematic Diagram (13/14).......................................... 4-174-18. MB-143 Board (FE_POWER/MOTOR DRIVE)
4-19. Waveforms ................................................................... 4-19E
5. PRINTED WIRING BOARDS
5-1. This Note Is Common For Printed Wiring Boards ........ 5-15-2. FR-316 Board (FRONT LEFT) Printed Wiring Board..... 5-25-3. MB-138 Board(MAIN) Printed Wiring Board (Side A) ..................................... 5-35-4. MB-138 Board (MAIN) Printed Wiring Board (Side B) ...................................... 5-4E
6. IC PIN FUNCTION DESCRIPTION ................... 6-1
7. SERVICE MODE ..................................................... 7-1
8. ERROR LOG LIST ................................................. 8-1
9. TROUBLESHOOTING ............................................. 9-1
10. REPAIR PARTS LIST
10-1. Exploded Views ............................................................ 10-1 10-1-1. Case Section ........................................................... 10-1 10-1-2. ........................................... 10-2 10-1-3.
Main Chassis Section ............................................................. 10-3
10-1-4. BD Section
.......................................................... 10-4 Accessories 10-2. Electrical Parts List ....................................................... 10-5
BDP-BX18/S185/S186
Schematic Diagram (14/14) ........................................ 4-18
MB-143 Board (USB) Schematic Diagram (6/14)......... 4-10
4-11. MB-143 Board (HDMI) Schematic Diagram (7/14)............................................ 4-114-12. MB-143 Board (ETHERNET) Schematic Diagram (8/14)............................................ 4-12
Circuit Boards Location
1-5. Rear Panel Assembly Caution................................... 1-23E
egaP eltiT noitceS egaP eltiT noitceS
1-3-2. Main functions ......................................................... 1-9
4-9.
MB-143 Board (CLK/POWER)
Schematic Diagram (4/14)............................................ 4-8
4-10.
MB-143 Board (FLASH/HOST) Schematic Diagram (5/14)............................................ 4-9
4-8.
MB-143 Board (POWER)
Schematic Diagram (3/14)............................................ 4-7
4-5.
Top Panel ...........
Switching Regulator. ....................................................
Drive..........
1-1
BDP-BX18/S185/S186SECTION 1
SERVICE NOTE
1-1. DISC REMOVAL PROCEDURE IF THE TRAY CANNOT BE EJECTED (FORCED EJECTION)
1. Remove the upper case. (Refer to page 2-1)2. Insert a clip in the hole of a drive and open a tray.
1-2. Work when optical device are replaced
Note: Please do the following work when you replace the optical device.
1. Install it in PC after downloading two set of software from following URL. (Refer to “1-4-8. BU Data Decode Jig” on page 1-19)
STEP 1 Microsoft .NET Framework Version 2.0 Redistributable Package (x86) http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=0856eacb-4362-4b0d-8edd-aab15c5e04f5
STEP 2 Microsoft .NET Framework 2.0 Service Pack 1 (x86) http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=79bc3b77-e02c-4ad3-aacf-a7633f706ba5
2. Take a photograph of the bar code on the optical device. The valid bar code photo as shown in Fig.2
3. Drag-and-drop the bar code photograph to the icon of decode software (BDPRdec). * The decode software is a complete set of “BDPRdec”, “Tasman.Bars.dll”, and “SavePath”. * Because decode software cannot be attached, it separately distributes it.
4. Input the password when you start decode software.* Inquire of each service headquarters because the password cannot be disclosed.
5. Write the decode data to the set. (Refer to “1-4-4. BU (Optical Block) Repair Guide” on page 1-16 and “1-4-5. BU Adjustment Flow [yy]” on page 1-17)
Fig.2
1 Insert paper clip inside hole
tray
3 Tray cover assy
2
1-2
1-3. TEST DISC
Part No. Description Layer
J-6090-199-A BLX-104 Single Layer
J-6090-200-A BLX-204 Dual Layer
J-2501-307-A CD (HLX-A1)
J-2501-305-A HLX-513 Single Layer (NTSC)
J-2501-306-A HLX-514 Dual Layer (NTSC)
J-6090-077-A HLX-506 Single Layer (PAL)
J-6090-078-A HLX-507 Dual Layer (PAL)
1-3-1. Operation and Display
Check Items1) BLX-104 1. Select 23.976Hz/1080p 2. Play “4.Motion pictures” 3. Check whether player can play back or not 4. Check each outputs Video: Composite/component/HDMI Audio: Digital out (Coaxial/Optical)/Audio out/5.1Ch output* When 1080/24p monitor is nothing, 1080i (59.94Hz or 50Hz) can use instead of 1080/24p. However this is temporary correspondence.
2) BLX-204 1. Select 1080i (59.94Hz or 50Hz) 2. Play “4.Motion pictures” 3. Check whether player can play back or not (Check the picture and sound output)
3) CD (HLX-A1) Check whether player can play back or not (Check the sound output)
4) HLX-513/514 (NTSC), HLX-506/507 (PAL) 1. After displayed Main Menu, select “1.Video” 2. Play “1.Color Bar 100%” (Check the picture and sound output) 3. Return to Menu 4. Play “Demonstration 4:3” or “5.Demonstration 16:9” (Check the picture and sound output)
BDP-BX18/S185/S186
1-3
1-3-1-1. BLX-104 Menu Function (1)Main Menu
X
X
X
X
X
X
X
X
X
X X X
X X X
X
1) When the disc is inserted, 1. Video Signal of 59.94Hz/1080i of the Main Menu is selectively displayed.
1-3-1-2. BLX-104 Menu Function (2)Main Menu
Sub_menu1 is displayedTo Main Menu after playback from T2_C1 to T19_C1To Main Menu after playback of T20_C1To Main Menu after playback of T21_C1
Sub_menu3 is displayedTo Main Menu after playback from T54_C1 to T60_C1To Main Menu after playback of T61_C1To Main Menu after playback of T62_C1
* When returning to Main Menu after playback from each button of 59.94Hz/1080i, 1. Video Signal of 59.94Hz/1080i is selectively dis-played.
* When returning to Main Menu after playback from each button of 50Hz/1080i, 1. Video Signal of 50Hz/1080i is selectively displayed.* 5. AV Sync does not operate.Note: Txx_ Cxx Chapter No. Title No.
BDP-BX18/S185/S186
1-4
1-3-1-3. BLX-104 Menu Function (3)Main Menu
To Main Menu after playback from T23_C1 to T40_C1
To Main Menu after playback of T41_C1
To Main Menu after playback of T42_C1
Sub_menu2 is displayed
To Main Menu after playback from T44_C1 to T50_C1To Main Menu after playback of T51_C1
To Main Menu after playback of T52_C1
Sub_menu4 is displayed
* When returning to Main Menu after playback from each button of 59.94Hz/720P, 1. Video Signal of 59.94Hz/720P is selectively dis-played.
* When returning to Main Menu after playback from each button of 23.976Hz/1080P, 1. Video Signal of 23.976Hz/1080P is selectively displayed.
* 5. AV Sync does not operate.
BDP-BX18/S185/S186
1-5
1-3-1-4. BLX-104 Menu Function (4)Sub menu1
X
X
X
X
X
X
1) At the display of Sub menu1, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu1 after seamless playback from T1_C1 to T1_C13. 1. Color Bar 100% is selec-
tively displayed on Sub menu1 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu1 after seamless playback from T1_C2 to T1_C13. 1. Color Bar 100% is selectively
displayed on Sub menu1 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu1, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 59.94Hz/1080i
is selectively displayed.6) Selection of LPCM Audio t Playback from T2_C1 to T19_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen.7) Selection of Dolby AC-3 Audio t Playback of T20_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen.8) Selection of Motion Picture t Return to Sub menu1 after playback of T21_C1. 1. ColorBar 100% is selectively displayed on Sub
menu1 screen.9) At the selection of Main Menu, 1. VideoSignal of 1080/59.94i of Main Menu is selectively displayed.10) AV Sync does not operate.
BDP-BX18/S185/S186
1-6
1-3-1-5. BLX-104 Menu Function (5)Sub menu2
X
X
X
X
X
X
1) At the display of Sub menu2, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu2 after seamless playback from T43_C1 to T43_C13. 1. Color Bar 100% is
selectively displayed on Sub menu2 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu2 after seamless playback from T43_C2 to T43_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu2 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu2, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of
23.976Hz/1080P is selectively displayed.6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen.7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen.8) Selection of Motion Picture t Return to Sub menu2 after playback of T52_C1. 1. Color Bar 100% is selectively displayed on Sub
menu2 screen.9) At the selection of Main Menu, 1. Video Signal of 1080/23.976P of Main Menu is selectively displayed.10) AV Sync does not operate.
BDP-BX18/S185/S186
1-7
1-3-1-6. BLX-104 Menu Function (6)Sub menu3
X
X
X
X
X
X
1) At the display of Sub menu3, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu3 after seamless playback from T53_C1 to T53_C13. 1. Color Bar 100% is
selectively displayed on Sub menu3 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu3 after seamless playback from T53_C2 to T53_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu3 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu3, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 50Hz/1080i
is selectively displayed.6) Selection of LPCM Audio t Playback from T54_C1 to T60_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen.7) Selection of Dolby AC-3 Audio t Playback of T61_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen.8) Selection of Motion Picture t Return to Sub menu3 after playback of T62_C1. 1. Color Bar 100% is selectively displayed on Sub
menu3 screen.9) At the selection of Main Menu, 1. Video Signal of 1080/50i of Main Menu is selectively displayed.10) AV Sync does not operate.
BDP-BX18/S185/S186
1-8
1-3-1-7. BLX-104 Menu Function (7)Sub menu4
X
X
X
X
X
X
1) At the display of Sub menu4, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu4 after seamless playback from T22_C1 to T22_C13. 1. Color Bar 100% is
selectively displayed on Sub menu4 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu4 after seamless playback from T22_C2 to T22_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu4 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu4, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 59.94Hz/720P
is selectively displayed.6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen.7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen.8) Selection of Motion Picture t Return to Sub menu4 after playback of T52_C1. 1. Color Bar 100% is selectively displayed on Sub
menu4 screen.9) At the selection of Main Menu, 1. Video Signal of 720/59.94P of Main Menu is selectively displayed.10) AV Sync does not operate.
BDP-BX18/S185/S186
1-9
1-3-2-1. BLX-204 Menu Function (1)Main Menu
X
X
X
X
X
X
X
X
X
X X X X
X X
X
X
X
1) When the disc is inserted, 1. Video Signal of 59.94Hz/1080i of the Main Menu is selectively displayed.
1-3-2-2. BLX-204 Menu Function (2)Main Menu
Sub_menu1 is displayedTo Main Menu after playback from T2_C1 to T19_C1
To Main Menu after playback of T20_C1
To Main Menu after playback of T21t T63t T64t T65t T66
Sub_menu3 is displayedTo Main Menu after playback of T54_C1-T60_C1t T83_C1-T94_C1To Main Menu after playback of T61_C1
To Main Menu after playback of T62t T82
To Main Menu after playback of T67_C1
To Main Menu after playback of T83_C1
* When returning to Main Menu after playback from each button of 59.94Hz/1080i, 1. Video Signal of 59.94Hz/1080i is selectively dis-played.
* When returning to Main Menu after playback from each button of 50Hz/1080i, 1. Video Signal of 50Hz/1080i is selectively displayed.Note: Txx_ Cxx Chapter No. Title No.
1-3-2 Menu Function
BDP-BX18/S185/S186
1-10
1-3-2-3. BLX-204 Menu Function (3)Main Menu
Sub_menu4 is displayed
To Main Menu after playback from T23_C1 to T40_C1To Main Menu after playback of T41_C1
To Main Menu after playback of T42_C1
Sub_menu2 is displayed
To Main Menu after playback of T44_C1-T50_C1t T71_C1-T81_C1To Main Menu after playback of T51_C1
To Main Menu after playback of T52_C1t T69
To Main Menu after playback of T68_C1
To Main Menu after playback of T70_C1
* When returning to Main Menu after playback from each button of 59.94Hz/720P, 1. Video Signal of 59.94Hz/720P is selectively dis-played.
* When returning to Main Menu after playback from each button of 23.976Hz/1080P, 1. Video Signal of 23.976Hz/1080P is selectively displayed.
BDP-BX18/S185/S186
1-11
1-3-2-4. BLX-204 Menu Function (4)Sub menu 1
X
X
X
X
X
X
1) At the display of Sub menu1, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu1 after seamless playback from T1_C1 to T1_C13. 1. Color Bar 100% is selec-
tively displayed on Sub menu1 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu1 after seamless playback from T1_C2 to T1_C13. 1. Color Bar 100% is selectively
displayed on Sub menu1 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu1, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of
59.94Hz/1080i is selectively displayed.6) Selection of LPCM Audio t Playback from T2_C1 to T19_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen.7) Selection of Dolby AC-3 Audio t Playback of T20_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu1 after playback. 1. Color Bar 100% is selectively displayed on Sub menu1 screen.8) Selection of Motion Picture t Return to Sub menu1 after playback of T21_C1. 1. Color Bar 100% is selectively displayed on Sub
menu1 screen.9) Selection of AV Sync t Return to Sub menu1 after playback of T67_C1. 1. Color Bar 100% is selectively displayed on Sub menu1
screen.10) At the selection of Main Menu, 1. Video Signal of 1080/59.94i of Main Menu is selectively displayed.
BDP-BX18/S185/S186
1-12
1-3-2-5. BLX-204 Menu Function (5)Sub menu 2
X
X
X
X
X
X
1) At the display of Sub menu2, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu2 after seamless playback from T43_C1 to T43_C13. 1. Color Bar 100% is
selectively displayed on Sub menu2 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu2 after seamless playback from T43_C2 to T43_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu2 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu2, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of
23.976Hz/1080P is selectively displayed.6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1 and from T71_C1 to T81_C1. SubPic that corresponds to Audio stream
1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen.7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu2 after playback. 1. Color Bar 100% is selectively displayed on Sub menu2 screen.8) Selection of Motion Picture t Return to Sub menu2 after playback of T52_C1 and T69. 1. Color Bar 100% is selectively displayed on
Sub menu2 screen.9) Selection of AV Sync t Return to Sub menu2 after playback of T70_C1. 1. Color Bar 100% is selectively displayed on Sub menu2
screen.10) At the selection of Main Menu, 1. Video Signal of 1080/23.976P of Main Menu is selectively displayed.
BDP-BX18/S185/S186
1-13
1-3-2-6. BLX-204 Menu Function (6)Sub menu 3
X
X
X
X
X
X
1) At the display of Sub menu3, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu3 after seamless playback from T53_C1 to T53_C13. 1. Color Bar 100% is
selectively displayed on Sub menu3 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu3 after seamless playback from T53_C2 to T53_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu3 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu3, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 50Hz/1080i
is selectively displayed.6) Selection of LPCM Audio t Playback from T54_C1 to T60_C1 and from T84_C1 to T94_C1. SubPic that corresponds to Audio stream
1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen.7) Selection of Dolby AC-3 Audio t Playback of T61_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu3 after playback. 1. Color Bar 100% is selectively displayed on Sub menu3 screen.8) Selection of Motion Picture t Return to Sub menu3 after playback of T62_C1 and T82. 1. Color Bar 100% is selectively displayed on
Sub menu3 screen.9) Selection of AV Sync t Return to Sub menu3 after playback of T83_C1. 1. Color Bar 100% is selectively displayed on Sub menu3
screen.10) At the selection of Main Menu, 1. Video Signal of 1080/50i of Main Menu is selectively displayed.
BDP-BX18/S185/S186
1-14
1-3-2-7. BLX-204 Menu Function (7)Sub menu 4
X
X
X
X
X
X
1) At the display of Sub menu4, 1. Color Bar 100% is selectively displayed.2) Selection of 1. Color Bar 100% t Return to Sub menu4 after seamless playback from T22_C1 to T22_C13. 1. Color Bar 100% is
selectively displayed on Sub menu4 screen.3) Selection of 2. Color Bar 75% t Return to Sub menu4 after seamless playback from T22_C2 to T22_C13. 1. Color Bar 100% is se-
lectively displayed on Sub menu4 screen.4) At the selection of 3 - 13, item 3 mentioned above is executed as the routine.5) At the display of Sub menu4, Main Menu is selected t Jump to Main Menu. At the display of Main Menu, 1. Video Signal of 59.94Hz/720P
is selectively displayed.6) Selection of LPCM Audio t Playback from T44_C1 to T50_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen.7) Selection of Dolby AC-3 Audio t Playback of T51_C1. SubPic that corresponds to Audio stream 1 is forcibly displayed. During the playback, when audio channel changes, the caption that corresponds to each audio stream is forcibly displayed. Return to
Sub menu4 after playback. 1. Color Bar 100% is selectively displayed on Sub menu4 screen.8) Selection of Motion Picture t Return to Sub menu4 after playback of T52_C1. 1. Color Bar 100% is selectively displayed on Sub
menu4 screen.9) Selection of AV Sync t Return to Sub menu4 after playback of T68_C1. 1. Color Bar 100% is selectively displayed on Sub menu4
screen.10) At the selection of Main Menu, 1. Video Signal of 720/59.94P of Main Menu is selectively displayed.
BDP-BX18/S185/S186
1-15
.4-1 DRIVE REPAIRING1-4-1.
Preparation
1-4-2. Checking Flow ~ Drive (BU) section ~
ESD Measures It is necessary to check the working space ESD condition before starting the Drive Part (BU) repairs
The ESD-resistance of BD Laser is weaker than DVD/CD LaserTo prevent ESD destruction, please make sure the working
space and human ESD.
Drive flowchart
BDP-S185 can play the BD-disc
BLX-104
BDP-S185 can play the DVD/CD-disc
Check Drive Power SupplyQ301 Pin 6: 12V
Q302 Pin 6: 5VCheck PS301, PS302
Replace PS when open
Check / replace the FFC cable, then check BDP-S185 operates normally
OP FFC cable (1-839-257-11)
Check the Optical Block Unit (BU) by service mode. (Flowchart zz)
BU IOP is OK?Replace the Optical Block Unit (BU)
Optical Block Unit (BU) replace (Flowchart yy)
OK
DVD: HLX-513CD: HLX-A1
NO
YES
NO
YES
YES
NO NO
NO
SPD FFC cable (1-839-258-11)
How to open FFC Holder. Refer below picture.
1
2
1
2
1
2
BDP-BX18/S185/S186
1-16
1-4-3. BU Check Flow [zz] ~
Before BU Replacement ~
1-4-4. BU (Optical Block) Repair Guide
BDP 6.9G (B D P-S1 8 5 ) series component structure is as same as conventional DVD Players.However BD player requires precise read out functions and also secure contents Protection system.Since above requirement, it is necessary to set/adjust BU data to EEPROM.
The following cases need Adjustments;(1)Replace BU (MB is original)(2)Replace MB (BU is original)(3)Replace both BU and MB
-,G RequirementDigital camera (recommend with macro mode)Barcode decoder (BDPRdec_ver2.0) installed in -,G PC’sUSB memory ESD work bench
3URFHGure (all cases) Refer the diagram
Remarks: The servo adjustment procedure will be carried out during OP data Writing.There is no manual adjustment procedure. LD ON TIME history doesn’t carry over. Do not touch any optical block parts, Turn Table and during replacing. BD Laser diode is very sensitive!
Optical Block Unit (BU) IOP check flow (zz) ~ [Before BU Replacement]
Enter Service ModePress ., ,
and plug in AC Power
,nside *Service Mode MenuSelect [8] Drive
,nside *DriveSelect [7] OP Check Menu
,nside *OP Check MenuSelect [2] d,OP then press 'ENTER'
Specification d,OPBD: 6mA
DVD, CD: 9mA
,OP out of specification need BU replacement
Optical Block Unit (BU) replace (Flowchart yy)AC Power OFF
NO
YES
+-+-
BDP-BX18/S185/S186
1-17
1-4-5. BU Adjustment Flow [yy] ~
1-4-6. KEM-470AAA/C2RP Packing Spec.
KEM-430AAA/C2RP Packing Spec.
Optical Block Unit (BU) OP Data Write Flow (yy) ~ [After BU/MB Replacement]
Remove the defective BU from Loading Assy and also remove BU insulator (4pcs)
Unpack new BU and take OP Data Barcode photo by camera
Assemble BU with Insulators to Loading Assy (tighten screw with 2kgf)
Decode the OP Data Barcode photo u s i ng BDPRdec.exe and save the test data to
USB memory(File Name: BuData.txt)
Enter Service Mode and insert USB memory to USB connector
Select [8] Drive --> Select [1] Drive OP data Write
Press ENTER
After Finishing ReWrite OP data--> Turn AC Power OFF
And confirm dIOP by select [7] OP Check Menu to verify IOP in specification
IOP in specification --> Turn AC Power OFF
Turn Power ON and check playback performance using BD, DVD and CD
BLX-104
DVD: HLX-513CD: HLX-A1
The following cases need OP Data Write:(1) Replace BU (MB is original)(2) Replace MB (BU is original)(3) Replace both BU and MB
JIG requirementDigital camera (with macro mode)Barcode decoder (BDPRdec.exe)installed in jigPC's (jig purpose)USB memoryESD free work bench
BDP-BX18/S185/S186
1-18
1-4-7. KEM-470AAA/C2RP Packing
1) Store it in Cushion Carton
2) Store it in Individual Carton
Individual Carton (4-272-629-0)
Antistatic Bag
InstructionManual
Cushion Carton
Antistatic Bag
Lid foam tray
2) Store the Cushion carton in the individual carton
C surface cut facing front
3) Store it in Master Carton
4) Master carton is sealedwith the PP tape.
Individual Carton (E430-BU-RP)
Stick it toH.
PPTape
Store 10 individual cartons 1 step X 2 steps= 20 individual cartons in the master carton.Master Carton (E430-BU-RP)
Shipment Label(Care Mark 3)
BDP-BX18/S185/S186
1-19
1-4-8. BU Data Decode Jig
BU Data Decode Jig
¶JIG Name: BDPRdec. exe
¶Version : 2.0.0.0
¶Software Contents:BDPRdec.exe ; SoftwareSavePath.ini ; decoded file destination setting file (initial destination is C:¥BuData.txt)Tasman.Bars.dll ; decode dllUninst.exe ; unistall BDPRd ec.exe from PC
¶Installations
STEP 1Microsoft .NET Framework Version 2.0 Redistributable Package (x86)http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=0856eacb-4362-4b0d-
8edd-aab15c5e04f5
STEP 2Microsoft .NET Framework 2.0 Service Pack 1 (x86)http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=79bc3b77-e02c-4ad3-
aacf-a7633f706ba5
*Hou to use Case1 Drag-and-drop 2Dcode photo onto BDPRdec.exe
Case2 Drag-and-drop BU data file onto BDPRdec.exe Data file name be changed to specify format and end of 7 character are defined Player : ****BDP.txt Recoder: ****BRD.txt #You can also enter the file path at the prompt.
*Remarks Do not change the decoded file name “BuData.txt”.
Release : 2010.11.26¶
1.Unzip files to any PC Folder 2.Check the attached 2D code photo(OK_sample.JPG) drag-and-drop onto BDPRdec.exe, the Password will be required at first time only, no need P/W from second time. 3.If there is the error message (.NET frame work requirements) please apply Microsoft .NET Framework 2.0 (or 2.0 SP1) from Microsoft download site.
BDP-BX18/S185/S186
1-20
1-4-10. Laser Caution Label
The Loading Ass’y service parts does not have Laser Caution Label.So that please reuse the original Laser Caution label and paste it on top of
new Loading Ass’y.
Limit SampleFollowing peel off condition are acceptable
1-4-9. Loading For Service
BDP 6G Loading Ass’y service parts consists from 3 parts.rHolder, Clamper AssysLoading AssytHolder FFC
Currently these parts are producing 2 vendors. But the THERE IS NO COMPATIBILITY.So, please DO NOT MIX ther ands of Loading for service and original Loading.
“Loading for service” A-1750-926-A
sLoading AssyLaser Caution Label
Holder, Clamper Assyr
t Holder, FFC 4-167-321-01
(FFC Holder can be used both service parts and original
parts)
1-839-258-11FFC
1-839-259-11FFC
1-839-257-11FFC
BDP-BX18/S185/S186
1-21
In case of BU assy replacement:
1. OP related data for new assy is controlled by BU factory 2. All of data is recorded into a barcode label3. The label is put on the assy4. Service parts will be followed5. In service, the data should be read out from problem assy6. The read data should be saved to new assy
Fact finding:
1. The label is “DATA MATRIX” format2. The number of data is 91 words3. The method of reading and saving is required when BU and
main board are replaced.
New service method
1. All of BU data on the barcode label is shot by digital camera inorder to make a JPEG file of BU data.
2. Application software in the PC makes digital data from JPEG file.
3. The converted data is stored to USB memory.
4. The USB memory is connected to BDP 6G unit.
5. In service mode, there is a command to save the data from USB memory to board memory.
BDP-BX18/S185/S186
1-22E
Shoot the barcodeFormat is JPEG
Application SoftwareData convert fromJPEG TEXT
Save the TEXT data
USB device is connected to symbol on the rear unit, and the TEXT data as new data is loaded to unit by service mode.
Description: BDPRdec.exe
When instruction to PC, password is required.
The password will be supplied to only service HQ, and service center name, q’ty and all of software registered information should be maintained by service HQ, and Video will ask to report the registration information.
BDP-BX18/S185/S186
2-1
BDP-BX18/S185/S186SECTION 2
DISASSEMBLY
This set can be disassembled in the order shown below.
Note: Follow the disassembly procedure in the numerical order given.
2-2. TRAY COVER ASSY
1 Insert paper clip inside hole
2-1. DISASSEMBLY FLOW
2-2.
TOP PANEL
(Page 2-1)
2-3.
TRAY COVER ASSY
(Page 2-2)
SET
(Page 2-5)
2-7.
(Page 2-5)
2-5. SWITCHING REGULATOR (Page 2-4)
2-6. MB-143 BOARD BD DRIVE
2-4.(Page 2-4)FR-316 boards
tray
3 Tray cover assy
2
2-2
BDP-BX18/S185/S186
2-3. TOP PANEL (1/2)
(2/2)
2-3
BDP-BX18/S185/S186
2-3. TOP PANEL (2/2)
(1/2)
2-4. FR-316 BOARD
FR-316 board4
One screws +BV3(3-CR)1
2-4
2-5. SWITCHING REGULATOR
Switching regulator
flexible flat3
3 harness(CN101)
6
BDP-BX18/S185/S186
cable (FIM-032)(CN701)
4 harness PM-168(CN201)
Two screws +BV3(3-CR)5
PS insulator2
USB shield case2
ESD Shield1
2-7. DRIVE
2-5
2-6. MB-143 BOARD
Three screw s +BV3(3-CR)
MB-143 board(CN2270)
3 Harness(PM-168)(CN301)
4
Flexibl e fla t(CN1101)
5
Flexibl e fla t6
(CN1002)
Flexibl e fla t
7
1
2 Flexible flat cable (FIM-032)
cable (LDG-003)
cable (OPT-003)
cable (SPD-003)(CN2260)
BDP-BX18/S185/S186
1 Two screws +BV3(3-CR)(tightening torque = 5.0 to 6.0NJIFP�
5 BD drive
4 Loading flexible flat cable (LDG-003)(CN2270)
3 Splindle flexible flat cable (OPT-003)(CN1101)
2 Optical flexible flat cable (SPD-003)
(CN2260)
BDP-BX18/S185/S186
2-8.
CIRCUIT BOARDS LOCATION
MB-143boa rd
FR-316 board
Switching Regulator
2-6E
L R CN801
L AN( 1 00
)
I C30
7
(AC
IN)
3-1
BD
P-B
X18
/S18
5/S
186
SE
CT
ION
3B
LO
CK
DIA
GR
AM
S
3-1.
OV
ER
AL
L B
LO
CK
DIA
GR
AM
PS301
PS302
The
com
pone
nts
iden
tifi e
d by
m
ark
or d
otte
d lin
e w
ith m
ark
are
crit
ical
for s
afet
y.R
epla
ce o
nly
with
par
t num
ber
spec
ifi ed
.
IC902
AUDIO
LINE
DRIVE
R
HDMI
USB
ETHE
RNET
VIDEO
AUDIO
(ANAL
OG OU
TPUT
)
(DIGIT
AL OU
TPUT
)AU
DIO
MB-14
3 BOA
RD
CN701
HDMI
OUT
COAX
IALAUD
IO
REGU
LATO
R
I C30
6I C
302
IC30
1I C
310
I C60
1I C
704
I C70
3
I C80
3
I C80
4
VIDEO
LINE O
UT
DIGITA
L OUT
PCM/D
TS/DO
LBY
DIGITA
L
SATA
I/F, M
EMOR
Y CON
TROL
,A/V
OUT, H
DMI, E
THER
NET I/
F,US
B I/F
MAIN
SYST
EM CO
NTRO
L, DSP
CXD9
0007G
-AA
IC101
J901
B-BUS
A-BUS
IC206
IC106
IC501
2G NA
NDFL
ASH X
40127M
HZ
CN201
IC710
REMO
TECO
NTRO
LRE
CEIVE
R
Blu-ra
yDV
D
DRIVE
BD DR
IVE
FR-31
6 BO
ARD D720
(WHIT
E)SW
ITCHIN
GRE
GULA
TOR
1.2V
3.3V
UNSW
5VUN
SW3.3
V
IC127
1
IC220
1
SA DRIVE
MOTO
R DR
IVE
S701
STOP
S702
OPEN
/CLOS
ES7
03
PLAY
DDR3
SDRA
M
I C60
3
S700
POWE
R
LED
IR KEY
1Gb D
DR3
2Gb D
DR3
1.5V
Q72
0LE
D D
RIV
ER
3-2
AC22
IC1
06
2G
b D
DR
3
SD
RA
M
X4
01
27
MH
Z
IC1
01
MA
IN S
YS
TE
M C
ON
TR
OL
,
DS
P,S
AT
A I
/F,M
EM
OR
Y C
ON
TR
OL
A/V
OU
T,H
DM
I,E
TH
ER
NE
T I
/F
US
B I
/F,
W24
RR
AS
DO
DQ
0-D
OD
Q15
DO
A0-D
OA1
2
RC
AS
RW
E
RO
DT
RC
LK0
RC
LKB
RC
LKE
RC
S
RBA
0
RBA
1
RBA
2W
25
AE23
H24
AE25
H25
L3J3
/CA
S/W
EO
DT
CK
/CK
CKE
/CS
/RA
S
BA0
K3 K9
J7K1 K7 L2
MB
-143
BO
ARD
IC2
06
1G
b D
DR
3S
DR
AM
RR
AS_B
DID
Q0-
DID
Q15
DIA
0-D
IA12
RC
AS_B
RW
E_B
RO
DT_
B
RC
LK0_
B
RC
LK0_
BR
CKE
_B
RC
S_B
RBA
0_B
RBA
1_B
RBA
2_B
Y12
AA6
AD22
AD10
AE22
AE10
/CA
S/W
EO
DT
CK
/CK
CKE
/CS
/RA
S
BA
0
AA12
AE11
A1
2
RFIP
G1
BD_R
F+23
MO
TOR
DR
IVE
IC22
01
RFIN
G2
BD_R
F-22
RFIP
2H
1D
VD_R
F+
26
RFIN
2H
2D
VD_R
F-
32IN
AC3
A
25
INB
B1B
28IN
CC2
C
20IN
DC1
D
17
INE
E2
E
34
INF
E1F
8
ING
D1
G
7
INH
D2H
6
FCS_
P27
40FC
S_N
2841
TRK_
P29
42TR
K_N
30
FD1
43TL
T_P
24
FR1
44TL
T_N
25
FD2
45FR
2
TDTR
LOAD
_N33
LOAD
-1
LOAD
_P
32LO
AD+
2
FE_T
RAY
INTR
AY-O
UT
3TR
AY-IN
5
U42
U4
V44
V
W46
W2
SLED
2_P
55
B+
8SL
ED2_
N56
B-
9
SLED
1_P
52
A
6SL
ED1_
N53
A-
7
FECFR
EQ
L4
SDIO
39
FECM
OD
K3
THER
MO
5
FEFM
O4
10
38FE
FMO
337
FE G
AIN
SW2
M3
36
VFC
S21
FE_F
OO
H4
VTR
K20
FE_T
RO
J2
FE_T
LO J
3VT
LT22
MO
NIT
OR
12FE
_ G
109
R5
VSLE
D2
17FE
_FM
ON
1
VSLE
D1
16FE
FM
O2
N2
VSPI
N18
FE_D
M0
VLO
AD19
FEO
SC
EN
L3
30 31 33 19
SCLK
LDD
_SEN
SA_B
+S
A_B
-
SA_A
+
SA
_A-
F5 N3 M2
9 87
2 3
FE_C
O_B
+
STEP
_EN
A
SA_B
SA_A
IC12
71
SA_D
RIV
E
FE _
TYPW
M
SPD
L
B12
T2 U4P2
IC5
01
16 18 8
CPU
_NFD
0 - C
PU_N
FD7
19
17 79
3-2.
DS
P B
LOC
K D
IAG
RA
M
A2T
B24
A24
E23
C24 B25
CPU
_NFC
EN
CPU
_NFC
LE
CPU
_NFA
LE
CPU
_NFW
EN
CPU
_NFR
EN
CPU
_NFR
BN
nCE
ALE
cLE
nRE
RY/
BYWE
NFW
P#
IC50
3 pi
n 1
2G
b
NA
ND
FL
AS
H
NS_
XTAL
O
NS
_XTA
LI
P3
3
CXD
9000
7G-A
A
BD
DR
IVE
CN1101
DVD
Blu
-ray
DR
IVE
CN2260 CN2270
BA1
BA2
/RES
ET
N8
M2
M3 K1
Y24
AC25
AB24
AD24
Y23
RR
ESET
N8
M2
M3 K1
W8
ABB
AC11
AE7
BA
1
BA
2
/RES
ET
L3J3 K3 K9
J7K1 K7 L2
RR
ESET
_B
AU
X1
BD
P-B
X18
/S18
5/S
186
FE_C
O_B
-
FE_C
O_A
+
FE_C
O_A
-
IN2
IN1
ENA
FE_T
RAY
OU
T
CE
C P
ULL
-UP
ISO
LATI
NG
SW
ITC
H
IC 101
IC902
C10 A7 B13
A13
B14
A14
B15
B16
A16
C20
A15
L R
T X2P
1 3 4 6 7 9 10 12 1 9 13C
EC
Q
702
UN
SW
3-3V
3-3
. A
VO
UT
B
LO
CK
D
IAG
RA
M
3-3
VIDEO
AUDIO
LINE O
UT
COAX
IALDIG
ITAL O
UTPC
M/DTS
/DOLB
YDIG
ITAL
CN701
J 901
AUDIO
LINE
DRIVE
ROU
TL OUTR
MUTE
INL INR
Q90
1
TX2N
TX1P
TX1N
TX0P
TX0N
TCKP
TCKN
TMDS
DATA
2+TM
DS DA
TA2-
TMDS
DATA
1+TM
DS DA
TA1-
TMDS
DATA
0+TM
DS DA
TA0-
TMDS
CLOC
K+
TMDS
CLOC
K-
HPD
CEC
HDMI
OUT
T X2P
TX2N TX1P
TX1N
TX0P
TX0N
TCKP
TCKN
CH2_P
CH2_M
CH1_P
CH1_M
CH0_P
CH0_M
CLK_
PCL
K_M
HTPL
G
SPDIF
AOLR
CK_R
ARO-R
ALO_
R
LORTNOC YROMEM F/I ATASF/I TENREHTE I MDH , TUO V/ A
F/I BSU90007G-AA DXC
PSD , LORTNOC METSYS NI AM
XAMU
TE
MB-14
3 BOA
RD
4P JA
CK
A10
B10
1 101192 7
BD
P-B
X18
/S18
5/S
186
VDAC
X_OU
T81B
CVBS
LINE O
UT
1
3
MB
-143
BO
AR
D
LAN
(100
)
A5 B5 A6 B6
B22
B23
A23 A22
D20
AA5
VC
LK
GP
IO 3
GP
IO 0
GP
IO4
GP
IO5
J22
J23
FR
-31
6 B
OA
RD
3 6 5 4
IC71
0R
EM
OTE
CO
NTR
OL
REC
EIV
ER
Q72
0LE
D D
RIV
ER
D72
0(W
HIT
E)
CN
70
1
CN
80
1
16
15
23
CN
20
1
DM
DP
3-4
. U
SB
/ET
HE
R
BL
OC
K
DIA
GR
AM
3-4
US
BE
XT
4 7 8
910
S701
S702
S703
DM
0
DP0
TXVN
_0
TXVP
_0
TXVN
_1
TXVP
_1
Y2
Y1
CXD
9000
7G-A
A
AC
4
AA5
BD
P-B
X18
/S18
5/S
186
3 6 5 416 15 910S7
00
IR
VS
TB
VD
ATA
CN
100
1
The
com
ponen
ts i
den
tifi e
d b
y m
ark
or d
ott
ed li
ne
with m
ark
are
crit
ical f
or s
afety
.R
epla
ce o
nly
with
part
num
ber
speci
fi ed.
1
5 3
5 3
66
C N301
1 2
1
SWITCHING REGULATOR :
IC 2
201
IC 6
01+5
V
FE_S
W12
V
FE_S
W5V
OPT
NIS
EC
ON
ICE
3.3V
UN
SW
3.3V3
.3V
MB
-14
3 B
OA
RD
3-5
E
3-5. POWER BLO
CK DIAGRAM
8 1
(AC IN
)
UNSW
12V
FE_G
ND
_M
CN
301
GN
D
FE-U
NS
W 1
2VP
S30
1FE
-UN
SW
12V
PC
ON
T1#
Q31
1M
OTO
RD
RIV
ER
CN
1003
CN
1001
HIG
H S
IDE
SW
ITC
H
USB_V
BU
S
CN
1101
IC10
6
IC20
6
DD
R3(
A)
DD
R3(
B)
1212 8 1
D72
0LE
D W
HIT
EQ
720
LED
DR
IVE
IC71
0R
EM
OTE
CO
NTR
OL
REC
EIV
ER
1EXT
CN
201
UN
SW
3.3V
SRV2253EK(EXCEPT:US,CND,CN)SRV2252UC(US,CND)
FR
-31
6 B
OA
RD
PS
302
CN
701
CN
1002
US
B
44
22
IC3
02
1.5V
PC
ON
T1#
1.5V
HD
MI O
UT
IC 7
05
+5V
REG
ULA
TOR
HD
MI 5
V
CN
701
PC
ON
T1
USB_P
CO
NT
1313
IC3
10
UN
SW
5V
IC12
71
DR
IVER
MO
TOR
BD
P-B
X18
/S18
5/S
186
UN
SW
5V
UN
SW
12V
19
CN
801
7ETH
ER
NET
IC3
06
3.3V
IC3
07
1.2V
IC 101
PC
ON
T1#
PO
WE
R/C
LOC
K/P
LL(1
.2V
)1.
2V
1.2V
1.2V
HD
MI
ETH
ER
PC
ON
T1#
3.3V
DD
R3(
AV
DD
33-M
EM
PLL
)
(CLO
CK
)D
VC
C3.
3_IO
(US
B)
AVD
D33
_USB
(HD
MI)
AVD
D33
_HD
MI
(ETH
ER
)AVD
D33
_LD
(ETH
ER
)AVD
D33
_CO
M
(VID
EO
)AVD
D33
_VD
AC
_R
24 6
IC9
02
AU
DIO
/VID
EO
IC5
03
IC5
01
NAN
D F
LASH
Q31
0
IC 1
161
+8V
REG
ULA
TOR
FE_8
VFE
_SW
12V
AVD
33_D
AC
AVD
33_L
DO
AV
D33
_IO
_STB
AVD
33_P
LLG
P
RESET_
IC3
01
UN
SW
3.3V
IC1
00
1
SYSC
ON
_RST
SYSC
ON
_RST
45FE
_SW
5VQ
302
Q31
2
SRV2254WW(CN)
99
GP
IO3
LED
_PO
WER
NF
WP
#
USB_O
CO
4-1
BDP-BX18/S185/S186
SECTION 4SCHEMATIC DIAGRAMS
All capacitors are in F unless otherwise noted. pF : F. 50V or less are not indicated except for electrolytics and tantalums.
All resistors are in ohms, 1/4 W (Chip resistors : 1 /10 W) un-less otherwise specified.
k =1000 , M =1000k . % : indicates tolerance. Caution when replacing chip parts.
New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, because
it is damaged by the heat. Constants of resistors, capacitors, ICs and etc with XX indicate
that they are not used. In such cases, the unused circuits may be indicated. All variable and adjustable resistors have characteristic curve B,
unless otherwise noted. : nonflammable resistor : fusible resistor : panel designation
f : internal component. : adjustment for repair. : B+ Line : B– Line
Circled numbers refer to waveforms. Voltages are dc between measurement point. Readings are taken with a color-bar signals on Blu-ray disc. Readings are taken with a digital multimeter (DC 10M ). Voltage variations may be noted due to normal production tolerances.
Note: The components identified by mark or dotted line with mark are critical for safety.Replace only with part num-ber specified.
Note: Les composants identifiés par une marque sont critiquens pour la sécurité.Ne les remplacer que par une pièce portant le numéro spéci-fié.
When indicating parts by reference number, please include the board name.
4-1. THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
1
A B C D E F G H I J
212
1311
109
87
65
43
14
BD
P-B
X18
/S18
5/S
186
4-2
4-2
. F
RA
ME
SC
HE
MA
TIC
DIA
GR
AM
4-3
1
A B C D E F G H I J
212
1311
109
87
65
43
14
4-3.
BO
ARD
(FR
ON
T LE
FT) S
CH
EMAT
IC D
IAG
RAM
See
pag
e 5-
3 fo
r p
rin
ted
wir
ing
bo
ard
.
- R
ef. N
o.:
boa
rd; 2
0,0
00
seri
es -
BD
P-B
X18
/S18
5/S
186
by m
ark
or
dotte
d lin
e w
ith
mar
k a
re c
ritic
al fo
r saf
ety.
Rep
lace
onl
y w
ith p
art n
umbe
r
FR
-31
6
FR-3
16
4-4. FR-316 BOARD (USB FRONT) SCHEMATIC DIAGRAM- Ref. No.: FR-316 board; 20,000 series -
�6HH�SDJH�����IRU�SULQWHG�ZLULQJ�ERDUG�
4-4
BDP-BX18�6����6186
2
FR-316 BOARD
31
A
B
4
45
BD
P-B
X18
/S18
5/S
186
1
A B C D E F G H I J
212
1311
109
87
65
43
14
4-5.
MB
-143
BO
AR
D (D
DR
3 A
)S
CH
EM
AT
IC D
IAG
RA
M (1
/12)
S
ee
pa
ge
5-4
fo
r p
rin
ted
wir
ing
bo
ard
.-
Ref
. N
o.:
MB
-143
b
oard
; 1
0,0
00
seri
es
4-6
BD
P-B
X18
/S18
5/S
186
1
A B C D E F G H I J
212
1311
109
87
65
43
14
4-6.
MB
-143
BO
AR
D (D
DR
3 B
) SC
HE
MA
TIC
DIA
GR
AM
(2/1
2)
Se
e p
ag
e 5
-4 f
or
pri
nte
d w
irin
g b
oa
rd.
- R
ef.
No.
: M
B-1
43
boa
rd;
10,
00
0 se
ries
4-7
BD
P-B
X18
/S18
5/S
186
1
A B C D E F G H I J
212
1311
109
87
65
43
14
4-7.
MB
-143
BO
AR
D (P
OW
ER
) S
CH
EM
AT
IC D
IAG
RA
M (3
/12)
S
ee
pa
ge
5-4
fo
r p
rin
ted
wir
ing
bo
ard
.-
Ref
. N
o.:
MB
-143
b
oard
; 1
0,0
00
seri
es
4-8
BD
P-B
X18
/S18
5/S
185
1
A B C D E F G H I J
212
1311
109
87
65
43
14
The
com
pone
nts
iden
tifi e
d by
mar
k o
r do
tted
line
with
m
ark
are
crit
ical
for s
afet
y.R
epla
ce o
nly
with
par
t num
ber
spec
ifi e
d.
4-8.
MB
-143
BO
AR
D (
CLK
/PO
WE
R) S
CH
EM
AT
IC D
IAG
RA
M (4
/12)
S
ee
pa
ge
5-4
fo
r p
rin
ted
wir
ing
bo
ard
.-
Ref
. N
o.:
MB
-143
b
oard
; 1
0,0
00
seri
es
B
DP
-BX
18/S
185/
S18
6
4-9
1
A B C D E F G H I J
212
1311
109
87
65
43
14
4-9.
MB
-143
BO
AR
D (F
LAS
H/H
OS
T) S
CH
EM
AT
IC D
IAG
RA
M (5
/12)
S
ee
pa
ge
5-4
fo
r p
rin
ted
wir
ing
bo
ard
.-
Ref
. N
o.:
MB
-143
b
oard
; 1
0,0
00
seri
es
IC5
03
4-10
BD
P-B
X18
/S18
5/S
186
1
A B C D E F G H I J
212
1311
109
87
65
43
14
4-10.
.M
B-1
43 B
OA
RD
(US
B)
SC
HE
MA
TIC
DIA
GR
AM
(6/1
2)
Se
e p
ag
e 5
-4 f
or
pri
nte
d w
irin
g b
oa
rd.
- R
ef.
No.
: M
B-1
43
boa
rd;
10,
00
0 se
ries
4-11
B
DP
-BX
18/S
185/
S18
64-
11. M
B-1
43 B
OA
RD
(HD
MI)
SC
HE
MA
TIC
DIA
GR
AM
(7/1
2)
Se
e p
ag
e 5
-4 f
or
pri
nte
d w
irin
g b
oa
rd.
- R
ef.
No.
: M
B-1
43
boa
rd;
10,
00
0 se
ries
B C D E F G H I J
212
1110
98
76
54
31
A
1
A B C D E F G H I J
212
1311
109
87
65
43
14
4-12
BD
P-B
X18
/S18
5/S
186
4-12
. M
B-1
43 B
OA
RD
(E
TH
ER
NE
T)
SC
HE
MA
TIC
DIA
GR
AM
(8/1
2)
Se
e p
ag
e 5
-4 f
or
pri
nte
d w
irin
g b
oa
rd.
- R
ef.
No.
: M
B-1
43
boa
rd;
10,
00
0 se
rie s
1
A B C D E F G H I J
212
1311
109
87
65
43
14
4-13
BD
P-B
X18
/S18
5/S
186
4-13
. M
B-1
43 B
OA
RD
(AU
DIO
VID
EO
)
SC
HE
MA
TIC
DIA
GR
AM
(9/1
2)
Se
e p
ag
e 5
-4 f
or
pri
nte
d w
irin
g b
oa
rd.
- R
ef.
No.
: M
B-1
43
boa
rd;
10,
00
0 se
ries 1
1
4-14
BD
P-B
X18
/S18
5/S
186
1
A B C D E F G H I J
212
1311
109
87
65
43
14
-
4-14
. M
B-1
43 B
OA
RD
(GP
IO/J
IAG
)
SC
HE
MA
TIC
DIA
GR
AM
(10
/ 12)
S
ee
pa
ge
5-4
fo
r p
rin
ted
wir
ing
bo
ard
.-
Ref
. N
o.:
MB
-143
b
oard
; 1
0,0
00
ser
ies
BD
P-B
X18
/S18
5/S
186
4-15
1
A B C D E F G H I J
212
1311
109
87
65
43
14
4-15
.MB
-143
BO
AR
D (F
E_P
OW
ER
/GIO
)
SC
HE
MA
TIC
DIA
GR
AM
(11/
12) S
ee
pa
ge
5-4
fo
r p
rin
ted
wir
ing
bo
ard
.-
Ref
. N
o.:
MB
-143
b
oard
; 1
0,0
00
seri
es
BD
P-B
X18
/S18
5/S
186
4-16
1
A B C D E F G H I J
212
1311
109
87
65
43
14
4-16
. MB
-143
BO
AR
D (
FE
_PO
WE
R/M
OT
OR
_DR
IVE
) S
CH
EM
AT
IC D
IAG
RA
M (1
2/12
) S
ee
pa
ge
5-4
fo
r p
rin
ted
wir
ing
bo
ard
.-
Ref
. N
o.:
MB
-143
b
oard
; 1
0,0
00
seri
es
MB-143 BOARD
H2.4Vp-p
B18 (VDACX_OUT)IC101 IC101 (NS_XTAL_I)
27 MHz3.3 Vp-p
Vpp
BDP-BX18/S185/S186
4-20E
4-20. WAVEFORMS
A12
1.0
5-1
SECTION 5PRINTED WIRING BOARDS
5-1. THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
2 1
3
2 1
3
2 1
3
3 4 5
2 1
1 2 3
6 5 4
E B
C
3 1
55
2
4 6
1 2 3
5 4Transistor Diode
� � ��8VHV�XQOHDGHG�VROGHUV�
� ���3DWWHUQ�IURP�WKH�VLGH�ZKLFK�HQDEOHV�VHHLQJ�
� �7KH�RWKHU�OD\HUV’�SDWWHUQV�DUH�QRW�LQGLFDWHG�
� 7KURXJK�KROH�LV�RPLWWHG�
� 7KHUH�are�IHZ�FDVHV�WKDW�WKH�SDUW�SULQWHG�on�GLDJUDP�isn’t�PRXQWHG�LQ�WKLV�PRGHO�
� ���SDQHO�GHVLJQDWLRQ
� &KLS�SDUWV�
Caution:3attern� IaFe� side���6,'(�%�
3DUWV�IDFH�VLGH�
(SIDE�$�
3DUWV�on�WKH�SDWWHUQ�IDFH�side�seen�IURP�WKH�SDWWHUQ�IDFH�DUH�LQGLFDWHG�
3DUWV�on�WKH�SDUWV�IDFH�side�seen�IURP�WKH�SDUWV�IDFH�DUH�LQGLFDWHG�
BDP-BX18/S185/S186
The
re a
re a
few
cas
es th
at th
e pa
rt is
n’t m
ount
ed in
this
mod
el is
prin
ted
on th
is d
iagr
am.
: U
ses
unle
aded
sol
der.
5-2.
F
R-3
16 B
OA
RD
(F
RO
NT
RIG
HT
) P
RIN
TE
D W
IRIN
G B
OA
RD
(S
IDE
A) �6HH�SDJH�����IRU�FLUFXLW�ERDUGV�ORFDWLRQ�
- R
ef. N
o.: F
R-3
16
bo
ard
; 2
0,0
00
se
rie
s -
FR
-316
BO
AR
D (
SID
E A
)
CN
201
A-6
D72
0 B
-5
IC71
0 B
-3
FR
-316
BO
AR
D (
SID
E A
)
AB
12
54
37
6
5-2
CN
701
A-3
12
54
37
6
AB
FR
-316
BO
AR
D (
SID
E B
)
11
11
BD
P-B
X18
/S18
5/S
186
1-88
4-34
2-
1-88
4-34
2-
FR
-316
BO
AR
D (
SID
E B
)
Q72
0B
-3
The
re a
re a
few
cas
es th
at th
e pa
rt is
n’t m
ount
ed in
this
mod
el is
prin
ted
on th
is d
iagr
am.
: U
ses
unle
aded
sol
der.
5-3.
M
B-1
43 B
OA
RD
(M
AIN
) P
RIN
TE
D W
IRIN
G B
OA
RD
(S
IDE
$�����6HH�SDJH�����IRU�FLUFXLW�ERDUGV�ORFDWLRQ�
- R
ef. N
o.: M
B-1
43 b
oard
; 10,
000
serie
s -
B
5-3
ABCDEF
12
54
36
MB-
143
BOAR
D (S
IDE
A)
CN
301
A-3
CN
801
E-3
CN
2260
D-1
CN
1101
A-1
CN
1002
A
-4C
N10
01
B-6
D60
5A
-5D
608
A-5
IC10
6 C
-4IC
307
B-3
IC10
1 C
-3IC
501
C-5
IC30
2 B
-4IC
306
B-4
IC31
0 B
-5IC
1001
C-6
X401
D-3
CN
2270
A
-2
IC22
01 D
-2IC
1271
B-2
Q90
1E-
5
MB
-143
BO
AR
D(S
IDE
A)
DP
-BX
18/S
185/
S18
6
11
1-88
3-98
1-
Q70
2D
-4
D31
5 A
-4Q
50 2
D-6
Q50
1D
-6
Q31
2A
-1
The
re a
re a
few
cas
es th
at th
e pa
rt is
n’t m
ount
ed in
this
mod
el is
prin
ted
on th
is d
iagr
am.
: U
ses
unle
aded
sol
der.
- R
ef. N
o.: M
B-1
43 b
oard
; 10,
000
serie
s -
5-4E
MB-
143
BOAR
D (S
IDE
B)
BD
P-B
X18
/S18
5/S
186
5-4.
M
B-1
43 B
OA
RD
(M
AIN
) P
RIN
TE
D W
IRIN
G B
OA
RD
(S
IDE
B)
�6HH�SDJH�����IRU�FLUFXLW�ERDUGV�ORFDWLRQ�
MB
-143
BO
AR
D(S
IDE
B)
B C D E
12
34
56
A
IC30
3 1
-DIC
314
4-E
11
1-88
3-98
1-
IC3
14
IC303
CN
1003
1-D
CN
1191
6-A
Pin Symbol Type DescriptionK9 DVCC12_K Power 1.2V digital power
K11 DVCC12_K Power 1.2V digital powerK12 DVCC12_K Power 1.2V digital powerK15 DVCC12_K Power 1.2V digital powerK17 DVCC12_K Power 1.2V digital powerK18 DVCC12_K Power 1.2V digital powerL9 DVCC12_K Power 1.2V digital power
L17 DVCC12_K Power 1.2V digital powerL18 DVCC12_K Power 1.2V digital powerN17 DVCC12_K Power 1.2V digital powerN18 DVCC12_K Power 1.2V digital powerP9 DVCC12_K Power 1.2V digital power
P18 DVCC12_K Power 1.2V digital powerR17 DVCC12_K Power 1.2V digital powerT9 DVCC12_K Power 1.2V digital power
T11 DVCC12_K Power 1.2V digital powerT12 DVCC12_K Power 1.2V digital powerT14 DVCC12_K Power 1.2V digital powerT16 DVCC12_K Power 1.2V digital powerT17 DVCC12_K Power 1.2V digital powerU9 DVCC12_K Power 1.2V digital power
U11 DVCC12_K Power 1.2V digital powerU12 DVCC12_K Power 1.2V digital powerU14 DVCC12_K Power 1.2V digital powerU15 DVCC12_K Power 1.2V digital powerU16 DVCC12_K Power 1.2V digital powerH14 DGND12_K Ground Digital groundH21 DGND12_K Ground Digital groundJ22 DGND12_K Ground Digital groundK21 DGND12_K Ground Digital groundL5 DGND12_K Ground Digital groundL6 DGND12_K Ground Digital groundL7 DGND12_K Ground Digital ground
L10 DGND12_K Ground Digital groundL11 DGND12_K Ground Digital groundL12 DGND12_K Ground Digital groundL13 DGND12_K Ground Digital groundL14 DGND12_K Ground Digital groundL15 DGND12_K Ground Digital groundL16 DGND12_K Ground Digital groundL21 DGND12_K Ground Digital groundM10 DGND12_K Ground Digital groundM12 DGND12_K Ground Digital groundM14 DGND12_K Ground Digital groundM16 DGND12_K Ground Digital groundN4 DGND12_K Ground Digital ground
N10 DGND12_K Ground Digital groundN11 DGND12_K Ground Digital groundN13 DGND12_K Ground Digital groundN15 DGND12_K Ground Digital groundN16 DGND12_K Ground Digital groundN22 DGND12_K Ground Digital groundN23 DGND12_K Ground Digital groundP10 DGND12_K Ground Digital groundP12 DGND12_K Ground Digital groundP14 DGND12_K Ground Digital groundP16 DGND12_K Ground Digital groundR4 DGND12_K Ground Digital ground
R10 DGND12_K Ground Digital groundR11 DGND12_K Ground Digital groundR12 DGND12_K Ground Digital groundR13 DGND12_K Ground Digital groundR14 DGND12_K Ground Digital groundR15 DGND12_K Ground Digital groundT21 DGND12_K Ground Digital groundU6 DGND12_K Ground Digital ground
U22 DGND12_K Ground Digital groundV5 DGND12_K Ground Digital groundY13 DGND12_K Ground Digital groundY15 DGND12_K Ground Digital groundY17 DGND12_K Ground Digital groundY19 DGND12_K Ground Digital ground
AA19 DGND12_K Ground Digital ground
MAIN SYSTEM CONTROL PIN FUNCTION (MB-143 BOARD IC 101 : CXD90007G-AB)
BDP-BX18/S285/S286
IC PIN FUNCTION DESCRIPTIONSECTION 6
6-1
AB13 DGND12_K Ground Digital groundAC18 DGND12_K Ground Digital groundF21 DVCC33_IO Power 3.3V Digital IO powerG20 DVCC33_IO Power 3.3V Digital IO powerJ9 DVCC33_IO Power 3.3V Digital IO power
J11 DVCC33_IO Power 3.3V Digital IO powerK8 DVCC33_IO Power 3.3V Digital IO powerL8 DVCC33_IO Power 3.3V Digital IO power
AB4 DVCC33_IO Power 3.3V Digital IO powerAC5 DVCC33_IO Power 3.3V Digital IO powerD21 DVCC33_IO_S TB Power 3.3V Digital IO power for Stand-By ModuleE22 DVCC33_IO_S TB Power 3.3V Digital IO power for Stand-By ModuleJ20 DDRVCCIO Power 1.5V Digital IO powerK19 DDRVCCIO Power 1.5V Digital IO powerL19 DDRVCCIO Power 1.5V Digital IO powerL20 DDRVCCIO Power 1.5V Digital IO powerN19 DDRVCCIO Power 1.5V Digital IO powerN20 DDRVCCIO Power 1.5V Digital IO powerP19 DDRVCCIO Power 1.5V Digital IO powerR20 DDRVCCIO Power 1.5V Digital IO powerT18 DDRVCCIO Power 1.5V Digital IO powerV14 DDRVCCIO Power 1.5V Digital IO powerV16 DDRVCCIO Power 1.5V Digital IO powerV17 DDRVCCIO Power 1.5V Digital IO powerV18 DDRVCCIO Power 1.5V Digital IO powerW15 DDRVCCIO Power 1.5V Digital IO powerW16 DDRVCCIO Power 1.5V Digital IO powerW18 DDRVCCIO Power 1.5V Digital IO powerY14 DDRVCCIO Power 1.5V Digital IO power
XTAL/PLLAA21 AVDD33_MEM PLL Power 3.3V Analog Power for MEMPLLAB19 AVSS33_MEM PLL Ground Analog Ground for MEMPLLAA22 TN_MEMPLL Analog Test PinAB23 TP_MEMPLL Analog Test PinH16 AVDD12_LDO Power 1.2V standby powerF17 AVDD33_LDO Power 3.3V power for standbyG16 AVSS33_LDO Ground Analog ground for standbyC12 AVDD33_PLLG P Power 3.3V Analog Power for PLL GroupC13 AVSS33_PLLG P Power Analog ground for PLL GroupA11 NS_XTALI I 27MHz Crystal InB11 NS_XTALO O 27MHz Crystal Out
AUDIO PWM DAC interfaceD12 AVDD33_DAC Power 3.3V Analog PowerE11 AVSS33_DAC Ground Analog Ground
Multiple function:(1) Audio output bit clock(2) Audio PWM output(3) GPIOMultiple function:(1) Audio output master clock(2) Audio PWM output(3) GPIO
Audio InterfaceMultiple function:(1) 1st Audio DAC mute(2) GPIOMultiple function:(1) Audio output left-right clock(2) 2nd Audio DAC mute(3) Video out DE signal(4) 2nd RS232 TX(5) External Interrupt 4(6) Slave I2C clock(7) PWM control signal output(8) Ethernet Activity LED(9) GPIOMultiple function:(1) Audio output serial data 0(2) 2nd Audio DAC mute(3) Video out DE signal(4) 2nd RS232 RX(5) External Interrupt 2(6) Slave I2C clock(7) PWM control signal output(8) Ethernet Duplex LED(9) GPIO
I/OAL0A10
B10
C10 AOLRCK I/O
AR0 I/O
U5 AMUTE I/O
D10 AOSDATA0 I/O
BDP-BX18/S285/S286
6-2
(1) Audio output serial data 1(2) Audio output master clock(3) Microphone input master clock(4) Video out DE signal(5) External Interrupt 1(6) 3th RS232 TX(7) Slave I2C clock(8) PWM control signal output(9) Ethernet Activity LED(10) GPIO
Multiple function:(1) Audio output serial data 2(2) Audio output bit clock(3) Microphone input bit clock(4) Video out DE signal(5) External Interrupt 4(6) 3th RS232 RX(7) Slave I2C clock(8) PWM control signal output(9) External Duplex LED(10) 1st Audio DAC mute(11) GPIO
Multiple function:(1) Audio output serial data 3(2) Audio output left-right clock(3) Microphone input left-right clock(4) Video out DE signal(5) External Interrupt 2(6) 2nd RS232 TX(7) Slave I2C clock(8) PWM control signal output(9) External Speed LED(10) GPIO
Multiple function:(1) Audio output serial data 4
(3) Microphone input data(4) Video out DE signal(5) External Interrupt 1(6) 2nd RS232 RX(7) Slave I2C clock(8) PWM control signal output(9) Ethernet Link LED(10) GPIO
Multiple function:(1) SPDIF digital audio output(2) GPIO
Analog Video Out InterfaceE16 AVDD33_VDA C Power 3.3 V Analog PowerD16 AVDD33_VDA C_R Power 3.3 V Analog PowerG14 AVSS33_VDAC Ground Analog GroundF14 AVSS33_VDAC_R Ground Analog GroundA18 VDACB_OUT Analog DAC outputC18 VDACG_OUT Analog DAC outputC17 VDACR_OUT Analog DAC outputB18 VDACX_OUT Analog DAC output
Digital Video Output Interface
Multiple function:(1) Video out mode: CLOCK(2) 2nd RS232 TX(3) Slave I2C clock(4) PWM control signal output(5) Ethernet Activity LED(6) NAND Flash Data input/output bit 5(7) Secure Disk interface clock(8) GPIO
Multiple function:(1) Video out mode: HSYNC(2) 2nd RS232 RX(3) Slave I2C data(4) External Interrupt 1(5) Ethernet Duplex LED(6) NAND Flash Data input/output bit 7(7) Secure Disk interface command(8) GPIO
VOUTCLKF22
I/OVOUTHSYNCH22
I/OAOSDATA2C8
I/OSPDIFA7
AOSDATA3D7
I/O, 5VAOSDATA4
C9 AOSDATA1 I/O
C7
I/O, 5V
I/O, 5V
Multiple function:
Multiple function:
6-3
BDP-BX18/S285/S286
Multiple function:(1) Video out mode: VSYNC(2) 3th RS232 TX(3) External interrupt 2(4) Ethernet Speed LED(5) NAND Flash Data input/output bit 6(6) Secure Disk interface data bit 0(7) GPIO
Multiple function:(1) Video out 16-bit 422 mode:C0(2) External Interrupt 4(3) 3th RS232 RX(4) Ethernet Link LED(5) NAND Flash Data input/output bit 4(6) Secure Disk interface data bit 1(7) GPIO
Multiple function:(1) Video out 16-bit 422 mode:C1(2) Slave I2C clock(3) NAND Flash Data input/output bit 3(4) Secure Disk interface data bit 2(5) GPIO
Multiple function:(1) Video out 16-bit 422 mode:C2(2) Slave I2C clock(3) NAND Flash Data input/output bit 2(4) Secure Disk interface data bit 3(5) GPIO
Multiple function:(1) Video out 16-bit 422 mode:C3(2) JTAG ICE data out(3) GPIO
Multiple function:(1) Video out 16-bit 422 mode:C4(2) JTAG ICE clock(3) GPIO
Multiple function:(1) Video out 16-bit 422 mode:C5(2) JTAG ICE data in(3) GPIO
Multiple function:(1) Video out 16-bit 422 mode:C6(2) JTAG ICE data in(3) GPIO
Multiple function:(1) Video out 16-bit 422 mode:C7(2) Audio line input data(3) GPIO
Multiple function:(1) Video out 16-bit 422 mode: Y0(2) Microphone input master clock(3) 2nd RS232 TX(4) Slave I2C clock(5) PWM control signal output(6) Ethernet Activity LED(7) NAND Flash Data input/output bit 1(8) GPIO
Multiple function:(1) Video out 16-bit 422 mode: Y1(2) Microphone input bit clock(3) 2nd RS232 RX(4) Slave I2C clock(5) External Interrupt 1(6) Ethernet Duplex LED(7) NAND Flash Data input/output bit 0(8) GPIO
Multiple function:(1) Video out 16-bit 422 mode: Y2(2) Microphone input left-right clock(3) 3th RS232 TX(4) Slave I2C clock(5) External Interrupt 2(6) Ethernet Speed LED(7) NAND Flash ready/busy
B25
I/OVOUTD5F24
I/OVOUTD7E24
I/OVOUTD8C25
I/OVOUTD9D24
I/O, 5VVOUTD10
I/OVOUTD6D25
I/OVOUTD3G23
I/OVOUTD4E25
I/OVOUTD1G24
I/OVOUTD2F25
I/OVOUTVSYNCG21
I/OVOUTDOG25
6-4
BDP-BX18/S285/S286
(8) GPIO
Multiple function:(1) Video out 16-bit 422 mode: Y3(2) Microphone input data(3) 3th RS232 RX(4) Slave I2C data(5) External Interrupt 4(6) Ethernet Link LED(7) NAND Flash ready enable(8) GPIO
Multiple function:(1) Video out 16-bit 422 mode: Y4(2) SPDIF input master clock (3) 2nd RS232 TX(4) Slave I2C clock(5) PWM control signal output(6) Ethernet Activity LED(7) NAND Flash chip enable(8) GPIO
Multiple function:(1) Video out 16-bit 422 mode: Y5(2) SPDIF input bit clock (3) 2nd RS232 RX(4) Slave I2C data(5) External Interrupt 1(6) Ethernet Duplex LED(7) NAND Flash command latch enable(8) GPIO
Multiple function:(1) Video out 16-bit 422 mode: Y6(2) SPDIF input left-right clock (3) 3th RS232 RX(4) Slave I2C clock(5) External Interrupt 2(6) Ethernet Speed LED(7) NAND Flash address latch enable(8) GPIO
Multiple function:(1) Video out 16-bit 422 mode: Y7(2) SPDIF input data(3) 3th RS232 RX(4) Slave I2C data(5) External Interrupt 4(6) Ethernet Link LED(7) NAND Flash write enable(8) GPIO
HDMI TXC16 AVDD12_HDMI_C Power 1.2V Analog PowerC15 AVDD12_HDMI_D Power 1.2V Analog PowerD14 AVDD33_HDMI Power 3.3V Analog PowerE14 AVSS33_HDMI Ground Analog GroundA15 CH0_M Analog HDMI TX data 0 differential pair (M)B15 CH0_P Analog HDMI TX data 0 differential pair (P)A14 CH1_M Analog HDMI TX data 1 differential pair (M)B14 CH1_P Analog HDMI TX data 1 differential pair (P)A13 CH2_M Analog HDMI TX data 2 differential pair (M)B13 CH2_P Analog HDMI TX data 2 differential pair (P)A16 CLK_M Analog HDMI TX clock differential pair (M)B16 CLK_P Analog HDMI TX clock differential pair (P)
NAND Flash InterfaceMultiple function:(1) NAND Flash address latch enable(2) GPOMultiple function:(1) NAND Flash chip enable(2) GPO
Multiple function:(1) NAND Flash 2nd chip enable(2) 2nd RS232 TX(3) External interrupt 2(4) 3th RS232 TX(5) Slave I2C clock(6) PWM control signal output(7) GPO
Multiple function:
AC6 NFALE I/O
AD4 NFCEN I/O
I/ONFCEN2AE5
I/O, 5VVOUTD14A24
I/OVOUTD15E23
I/O, 5VVOUTD12A25
I/O, 5VVOUTD13B24
I/O, 5VVOUTD11C24
6-5
BDP-BX18/S285/S286
(1) NAND Flash command latch enable(2) GPO
I/OAD5 NFCLE
Multiple function:(1) NAND Flash Data input/output bit 0(2) GPIOMultiple function:(1) NAND Flash Data input/output bit 1(2) GPIOMultiple function:(1) NAND Flash Data input/output bit 2(2) GPIOMultiple function:(1) NAND Flash Data input/output bit3(2) GPIOMultiple function:(1) NAND Flash Data input/output bit4(2) GPIO
Multiple function:(1) NAND Flash Data input/output bit5(2) GPIOMultiple function:(1) NAND Flash Data input/output bit6(2) GPIO
Multiple function:(1) NAND Flash Data input/output bit7(2) GPIOMultiple function:(1) NAND Flash ready/busy(2) GPIO
Multiple function:(1) NAND Flash 2nd ready/busy(2) 2nd RS232 RX(3) External interrupt 1(4) 3th RS232 RX(5) Slave I2C data(6) PWM control signal output(7) GPO
Multiple function:(1) NAND Flash read enable(2) GPOMultiple function:(1) NAND Flash write enable(2) GPO
Dram ChannelAA25 RA0 O Memory address bit 0U21 RA1 O Memory address bit 1
AB25 RA2 O Memory address bit 2AA23 RA3 O Memory address bit 3W21 RA4 O Memory address bit 4AA24 RA5 O Memory address bit 5W22 RA6 O Memory address bit 6AB24 RA7 O Memory address bit 7W20 RA8 O Memory address bit 8
AC24 RA9 O Memory address bit 9AD23 RA10 O Memory address bit 10V22 RA11 O Memory address bit 11AA20 RA12 O Memory address bit 12AD25 RA13 O Memory address bit 13Y24 RBA0 O Memory bank address bit 0
AE24 RBA1 O Memory bank address bit 1AD24 RBA2 O Memory bank address bit 2AC22 RCAS_ O Memory column address strobeAE23 RCKE O Memory clock enableH24 RCLK0 O Memory clock 0 positiveH25 RCLK0_ O Memory clock 0 negativeY23 RCS_ O Memory chip selectV24 RDQ0 I/O Memory data bit 0V23 RDQ1 I/O Memory data bit 1U25 RDQ2 I/O Memory data bit 2U23 RDQ3 I/O Memory da
Recommended