View
230
Download
0
Category
Preview:
Citation preview
8/14/2019 Setup of NetApp v1.a1.ppt
1/34
Setup of NetApp gFiler
Gateway Series
8/14/2019 Setup of NetApp v1.a1.ppt
2/34
Installation Steps
List of what the customer must providePhysical hardware & cabling setupIssues for clustering or stand alone setupConfiguration of storage subsystem9970VSetup Console for initial Gateway accessBoot Gateway from flash compactdiskInitial boot up of GatewaySet environmental variables
Re-boot Gateway to initialize Luns or Lun x/Vol0Special boot menu (called Floppy boot menu)Configure Network interfaces on GatewayAdd Licenses for NFSInstall On-Tap OS 6.4.1 from Unix Admin (NFS)(or) Install On-Tap OS 6.4.1 from Windows Admin (CIFS)Configure NTPConfigure Time Zone to match network serviceConfirm installation (some handy commands)
8/14/2019 Setup of NetApp v1.a1.ppt
3/34
Racking and Cabling
Unpack Save license papers!
Rack (3 man job!)
Cable up fibre to Array (cable all paths)
Power Both supplies & cluster ps
Ethernet Management port
Gig-e Ports Console port (for initial config & possible recovery)
8/14/2019 Setup of NetApp v1.a1.ppt
4/34
What the customer must provide
2 IP addresses (Access & Management) Gateway address Netmasks DNS servers
3 power feeds (110/220) CIFS (Windows file server) Domain Name WINS/DC ip address Membership in Domain
NFS NIS server? UNIX admin host IP (trusted host for administration)
8/14/2019 Setup of NetApp v1.a1.ppt
5/34
Cluster Configuration
Make sure both gFilers are cabled together and that theyare both powered up.
Set the environmental variables FIRST on both gFilersfirst before proceedings to install the Data ONTAP setenv LUN-ownership low/high
setenv oprah-style true
setenv java? true
setenv jit-enable? true
8/14/2019 Setup of NetApp v1.a1.ppt
6/34
Configure storage
If direct connect FCAL
Fabric Off
No LUN security
If through a switch Fabric On
Use LUN Security & Zoning
(Each NetApp HBA should see only one copy of each LUN.
See Appendix A for gFiler/Storage configurations) Present consecutive LUNs in order starting at 0
(Will not detect high numbered LUNs without lower ones for no-clustered configuration)
8/14/2019 Setup of NetApp v1.a1.ppt
7/34
Boot Flash Upgrade
You may need to upgrade the Boot Flash if you areunable to discover LUNs from an HDS storagesubsystem. See Appendix B for detailed instructions onhow to upgrade the Boot Flash .
8/14/2019 Setup of NetApp v1.a1.ppt
8/34
Configure NetApp ROM
Attach to the NetApp console using the provided serialcable with an application like HyperTerm or SecureCRT Settings
Bits per Second: 9600
Data Bits: 8
Parity: None
Stop Bits: 1
Flow Control: No flow control
Expect that the first boot will fail and yield an OK>prompt
8/14/2019 Setup of NetApp v1.a1.ppt
9/34
Boot messages
Intel Open Firmware by FirmWorksCopyright 1995-2003 FirmWorks, Network Appliance. All Rights Reserved.Firmware release 4.2_i2Press Del to abort boot, Esc to skip POST
Memory size is 4096 MBTesting SIOTesting LCD
Probing devicesMemory size: 4096MBTesting 512MBCompleteFinding image...Loading /pc-card:\x86\kernel\primary.krn
Starting Press CTRL-C for special boot menu................................................................................
................................................................ MTL_MODULE(1): Initializing IB interconnect.NetApp Release 6.4X11: Fri Jan 31 08:02:30 PST 2003Copyright (c) 1992-2003 Network Appliance, Inc.Starting boot on Sun Feb 16 00:27:37 GMT 2003
Boot Post Messages(Make sure firmware is 4.2.i2 orlater)
Loading kernel Imagefrom boot flash
Special Boot menu
(not used for first config)
Successful loadof flash image
8/14/2019 Setup of NetApp v1.a1.ppt
10/34
Boot messagesFound 3 LUNs on device 4a.0L0Found 3 LUNs on device 4b.0L0Found 3 LUNs on device 8a.0L0Found 3 LUNs on device 8b.0L0DBG: OFW LUN_ownership not setDBG: OFW LUN_ownership not setDBG: OFW LUN_ownership not setDBG: OFW LUN_ownership not setDBG: OFW LUN_ownership not setDBG: OFW LUN_ownership not set
Sun Feb 16 00:27:45 GMT [config.noPartnerLUNs:CRITICAL]: No LUNs were detectedor the partner; this node will be unable to takeover correctly
PANIC: OFW LUN_ownership not set in process dmgr_thread on release NetAppReleas
e 6.4X11 on Sun Feb 16 00:27:45 GMT 2003
version: NetApp Release 6.4X11: Fri Jan 31 08:02:30 PST 2003cc flags: 3O
DUMPCORE: START
DUMPCORE: END -- coredump *NOT* written.halt after panic during system initializationProgram terminatedok
We found 3 LUNSOn each path
However the NetAppWants to know who owns
These LUNs?
Since there are no LUNswith a bootable OS & noownership is set we cant boot
So since we cant boot a
core dump occurs andyields an OK> prompt
8/14/2019 Setup of NetApp v1.a1.ppt
11/34
Configure NetApp Prom
Did it see any storage? Link lights Messages showing storage discovery Found X LUNs on device
AA.bbb
Set enviornmental variables OK> setenv oprah-style true If it is the first cluster (or unclustered) ok> setenv LUN-ownership
low If it is the second member of the cluster: ok> setenv LUN-
ownership high
OK> setenv java? trueOK> setenv jit-enable? true
Reboot Ok> boot
8/14/2019 Setup of NetApp v1.a1.ppt
12/34
Initializing/zeroing out disks
If there is data already on the disks theNetApp will see the drives as unavailable
Need to enter special boot menu and zeroout disks
If the NetApp sees the disks as alreadyzeroed out then the boot menu will skip tothe first time configuration questions.
8/14/2019 Setup of NetApp v1.a1.ppt
13/34
Example Using special boot menuto zero out disks
Intel Open Firmware by FirmWorksCopyright 1995-2003 FirmWorks, Network Appliance. All
Rights Reserved.Firmware release 4.2_i2Press Del to abort boot, Esc to skip POST
Memory size is 4096 MB
Testing SIOTesting LCDProbing devicesMemory size: 4096MBTesting 512MBCompleteFinding image...Loading /pc-card:\x86\kernel\primary.krn
Starting Press CTRL-C for special boot menu................................................................................................................................................Special boot options menu will be available. MTL_MODULE(1): Initializing IB interconnect.
Press CTRL-C to go to
special boot menu
CTRL-C recognizedWill boot into menu
8/14/2019 Setup of NetApp v1.a1.ppt
14/34
Example Using special boot menuto zero out disks
NetApp Release 6.4X11: Fri Jan 31 08:02:30 PST 2003Copyright (c) 1992-2003 Network Appliance, Inc.Starting boot on Sun Feb 16 15:51:28 GMT 2003Found 3 LUNs on device 4a.0L0LUN Ownership using low rangeSun Feb 16 15:52:00 GMT [config.noPartnerLUNs:CRITICAL]:No LUNs were detected for the partner; this node will be unableto takeover correctly
This boot is of OS version: NetApp Release 6.4X11.The last time this filer booted, it used OS version: .The WAFL/RAID versions of the previously booted OS are unknown.If you choose a boot option other than Maintenance mode orInitialize disks, the file system of your filer might be upgradedto a new version of the OS.If you do not want to risk having your file system upgraded, chooseMaintenance mode or reboot using the correct OS version.
(1) Normal boot.(2) Boot without /etc/rc.(3) Change password.(4) Initialize all disks.(5) Maintenance mode boot.
We want the NetApp toInitialize the disks that itcan see. So we select 4
8/14/2019 Setup of NetApp v1.a1.ppt
15/34
Example Using special boot menuto zero out disks
Selection (1-5)? 4
Install a new file system? y
This will erase all the data on the disks, are you sure? yes
Sun Feb 16 15:52:27 GMT [raid.vol.disk.add.done:notice]:Addition of disk 4a.0L2 (S/N 045150060002) to volumevol0 has completed successfully
Sun Feb 16 15:52:28 GMT [config_async_0:notice]:
Volume vol0 has been added to the system.
8/14/2019 Setup of NetApp v1.a1.ppt
16/34
Booting the OS
The gFiler will boot up and prompt you toanswer questions to configure it.
If you make a mistake it can be correctedafterwards (options setting )
On the first boot the NetApp will attempt toDHCP e0 (the onboard Ethernet). We willchange the IP to the customer specifiedvalue.
8/14/2019 Setup of NetApp v1.a1.ppt
17/34
First Boot (Configuring SystemParameters)
ifconfig e0 mediatype autoConfiguring onboard ethernet e0.Contacting DHCP server.Ctrl-C to skip DHCP search ...Sun Feb 16 23:15:22 GMT [rc:info]: Contacting DHCP serverSun Feb 16 23:15:23 GMT [10/100-IV/e0:info]: Ethernet e0: Link up.Configuring e0 using IP 10.3.21.238 netmask 255.255.254.0.ifconfig e0 up mediatype auto netmask 255.255.254.0 10.3.21.238Sun Feb 16 23:15:34 GMT [rc:info]: DHCP config successful
NetApp Release 6.4X11: Fri Jan 31 08:02:30 PST 2003System ID: 0050390937 (); partner ID: ()System Serial Number: 1034194 ()System Rev: C2
Backplane Part Number: 104-00013Backplane Rev: C2Backplane Serial Number: 1034194slot 0: System Board
Processors: 1Memory Size: 3072 MB
slot 0: 10/100 Ethernet Controller IVe0 MAC Address: 00:a0:98:01:12:15 (auto-100tx-fd-up)
slot 0: NetApp ATA/IDE Adapter ata0a (1f0)ata0a.0 30MB
slot 1: Remote Management Controllerslot 4: FC Host Adapter 4a
3 Disks: 90.3GB
slot 4: FC Host Adapter 4b3 Disks: 90.3GB
slot 5: Dual 10/100/1000 Ethernet Controller Ve5a MAC Address: 00:07:e9:15:08:d0 (auto-unknown-cfg_down)e5b MAC Address: 00:07:e9:15:08:d1 (auto-unknown-cfg_down)
slot 6: Interconnect HBAslot 7: NVRAM
Memory Size: 256 MBslot 8: FC Host Adapter 8a
3 Disks: 90.3GBslot 8: FC Host Adapter 8b
3 Disks: 90.3GBslot 9: Gigabit Ethernet Controller IV
e9 MAC Address: 00:02:b3:c1:e2:63 (auto-unknown-cfg_down)
8/14/2019 Setup of NetApp v1.a1.ppt
18/34
First Boot (Configuring SystemParameters)
(auto-unknown-cfg_down)Please enter the new hostname []: dexterDo you want to configure virtual network interfaces? [n]: nPlease enter the IP address for Network Interface e0 [10.3.21.238]: 10.3.20.134Please enter the netmask for Network Interface e0 [255.255.254.0]:Should interface e0 take over a partner IP address during failover? [n]:Please enter media type for e0 {100tx-fd, tp-fd, 100tx, tp, auto} [auto]: 100tx-fdPlease enter the IP address for Network Interface e5a []:Should interface e5a take over a partner IP address during failover? [n]:Please enter the IP address for Network Interface e5b []:Should interface e5b take over a partner IP address during failover? [n]:Please enter the IP address for Network Interface e9 []:
Should interface e9 take over a partner IP address during failover? [n]:Please enter the IP address for Network Interface e10a []:Should interface e10a take over a partner IP address during failover? [n]:Please enter the IP address for Network Interface e10b []:Should interface e10b take over a partner IP address during failover? [n]:Please enter the IP address for Network Interface e11 []:Should interface e11 take over a partner IP address during failover? [n]:Would you like to continue setup through the web interface? [n]:Please enter the name or IP address of the default gateway: 10.3.20.1
The administration host is given root access to the filer's/etc files for system administration. To allow /etc root accessto all NFS clients enter RETURN below.
Please enter the name or IP address of the administration host: 10.3.20.91
Where is the filer located? []: HDS TRC San Diego Lab (Row 2, Rack0)Do you want to run DNS resolver? [n]: yPlease enter DNS domain name [hds.com]: trc.hds.comYou may enter up to 3 nameserversPlease enter the IP address for first nameserver [10.1.7.34]: 10.3.20.215Do you want another nameserver? [y]: yPlease enter the IP address for alternate nameserver [10.1.7.33]: 140.243.186.22
Do you want another nameserver? [n]:Do you want to run NIS client? [n]:
8/14/2019 Setup of NetApp v1.a1.ppt
19/34
First Boot (Configuring SystemParameters)
This system will send event messages and weekly reportsto Network Appliance Technical Support. To disable this feature,enter "options autosupport.support.enable off" within 24 hours.
Enabling Autosupport can significantly speed problem determinationand resolution should a problem occur on your system.For further information on Autosupport, please see:.http://now.netapp.com/autosupport/
Press the return key to continue.
The remote management controller (RMC) extends autosupport by sendingadditional system event alerts. Your autosupport settings are usedfor sending these alerts via email over the RMC LAN interface.
Would you like to configure the RMC LAN interface [y]: yThe MAC address for the dedicated RMC LAN interface is 00:30:d3:06:29:7e.Would you like to enable DHCP on the RMC LAN interface [y]: nPlease enter the IP address for the RMC []: 10.3.20.135Please enter the netmask for the RMC []: 255.255.254.0Please enter the IP address for the RMC gateway []: 10.3.20.1Please enter media type for the RMC {100tx-fd, tp-fd, 100tx, tp, auto} [auto]: 100tx-fd
The mail host is required by your system to send RMCalerts and local autosupport email.
Please enter the name or IP address of the mail host: 10.3.20.91You may use the autosupport options to configure alert destinations.
Now unpack the tar file provided on the tar floppies into the rootdirectory of the filer. When you are done, type "download"to install the boot image on the hard disk and "reboot" tobegin using the new image.
Proceed to the administration host youspecified earlier in the setup
8/14/2019 Setup of NetApp v1.a1.ppt
20/34
First Boot (Configuring SystemParameters)
Sun Feb 16 23:20:24 GMT [init_java:warning]: Java disabled: Missing /etc/java/rt131.jar.Sun Feb 16 23:20:24 GMT [init_zapi:warning]: Zapi RPC is disabled: java not enabledSun Feb 16 23:20:24 GMT [httpd_servlet:warning]: Java Virtual Machine not accessibleSun Feb 16 23:20:24 GMT [ems.engine.startReplay:info]: Replay begins for EMS boot-time cacheSun Feb 16 23:20:24 GMT [ems.engine.endReplay:info]: Replay ends for EMS boot-time cacheSun Feb 16 23:20:24 GMT [dyn_dev_qual_admin:info]: Firmware is up-to-date on all disk drives
Sun Feb 16 23:20:26 GMT [10/100-IV/e0:info]: Ethernet e0: Link being reconfigured.add net default: gateway 10.3.20.1There are 5 spare disks; you may want to use the vol command to create new volumes or add disks to the existing volume.Sun Feb 16 23:20:27 GMT [savecore_admin:info]: saving 102M to core.0.nz ("raid:there are no data or parity disks in process rc on release NetApp Release 6.4X11")
Sun Feb 16 23:20:27 GMT [mgr.boot.floppy_done:info]: NetApp Release 6.4X11 floppy boot complete.Sun Feb 16 23:20:27 GMT [cf.fm.unexpectedAdapter:warning]: Warning: clustering is not licensed yet an interconnect adapter was found. NVRAM will be divided into two parts
until adapter is removedSun Feb 16 23:20:27 GMT [mgr.boot.reason_ok:notice]: System rebooted.Sun Feb 16 23:20:27 GMT [asup_main:warning]: minimal Autosupports unavailable.Could not read /etc/asup_content.confSun Feb 16 23:20:27 GMT [asup_main:warning]: minimal Autosupports unavailable.Could not read /etc/asup_content.confSun Feb 16 23:20:28 GMT [sysconfig.sysconfigtab.openFailed:notice]: sysconfig: table of valid configurations (/etc/sysconfigtab) is missing.
dexter> Sun Feb 16 23:20:28 GMT [console_login_mgr:info]: root logged in from consoleSun Feb 16 23:20:29 GMT [sysconfig.sysconfigtab.openFailed:notice]: sysconfig: table of valid configurations (/etc/sysconfigtab) is missing.
Sun Feb 16 23:20:31 GMT [savecore_admin:info]: core.0.nz processing completed.Sun Feb 16 23:20:31 GMT [savecore_admin:info]: Generating /etc/crash/mini-core.0Sun Feb 16 23:20:31 GMT [10/100-IV/e0:info]: Ethernet e0: Link up.Sun Feb 16 23:20:31 GMT [savecore_admin:info]: (/etc/crash/mini-core.0) generation completed.Sun Feb 16 23:20:41 GMT [rmc.connect:warning]: The remote management controllerin slot 1 is missing its LAN cable. Please connect it as soon as possible.
dexter>
8/14/2019 Setup of NetApp v1.a1.ppt
21/34
Add Licenses
In order to install the Data ONTAP software you will need to activateeither CIFS, NFS or HTTP (depending on the administration host)which requires a license.
dexter> license add QAPXI
A nfs license has been installed.nfs enabled.
dexter> Sun Feb 16 23:21:54 GMT [rc:notice]: nfs licensed
dexter> license add HHJNLA http license has been installed.
Use "options httpd.enable" to enable http.dexter> Sun Feb 16 23:22:13 GMT [rc:notice]: http licensed
8/14/2019 Setup of NetApp v1.a1.ppt
22/34
Update Data ONTAP software
Even if it is already at 6.4 update the filer (no java) Download code Download release notes Download install docs
8/14/2019 Setup of NetApp v1.a1.ppt
23/34
Installing/Updating Data ONTAPsoftware from UNIX
Mount filer Copy code to filer root Extract tar file
Run install script Unmount filer From filer console run
download command
Reboot filer
ADMINHOST /># mount filer:/ /mnt
ADMINHOST /># cp 64_sysfiles_I.tar /mnt
ADMINHOST /># cd /mnt
ADMINHOST /mnt># tarxvf
64_sysfiles_I.tarADMINHOST /mnt># ./install_netapp /mnt
(completes sucessfully)
ADMINHOST /mnt># cd /
ADMINHOST /># umount /mnt
8/14/2019 Setup of NetApp v1.a1.ppt
24/34
Installing/Updating Data ONTAPsoftware from Windows 2K
After successfully installing the CIFS license, map the C$ drive from thegFiler to a drive letter on the administration host.
Load the NetApp Data ONTAP CD that came with the gFiler on theadministration host and change directories on the CD to
\ONTAP\6_4_1\X86. Execute the setup.exe command making sure youare extracting the files into the /etc directory under \\\C$.
From the gFiler console run the command download. Wait until the
download command finished then reboot the gFiler.
Note: If you are unable or are having problems adding the gFiler into the Windows domain choose Windows
Workgroup authentication using the filers user accounts, option 2 in cifs setup. You can rerun cifs setup again
to add the gFiler to the domain at a later date.
http://localhost/var/www/apps/conversion/tmp/scratch_1//%3Cfiler_name%3E/C$http://localhost/var/www/apps/conversion/tmp/scratch_1//%3Cfiler_name%3E/C$http://localhost/var/www/apps/conversion/tmp/scratch_1//%3Cfiler_name%3E/C$http://localhost/var/www/apps/conversion/tmp/scratch_1//%3Cfiler_name%3E/C$http://localhost/var/www/apps/conversion/tmp/scratch_1//%3Cfiler_name%3E/C$http://localhost/var/www/apps/conversion/tmp/scratch_1//%3Cfiler_name%3E/C$8/14/2019 Setup of NetApp v1.a1.ppt
25/34
Configure NTP
Time synchronization is Important!
2 options NTP or rdate. NTP is preferred, but it is important that WindowsDoman Controllers, NFS clients, and Filer all be synchronized to a commontime source.
From filer console:
>options set timed.proto ntp
>options set timed.servers 10.3.20.1
>options set timed.enable on
8/14/2019 Setup of NetApp v1.a1.ppt
26/34
Set Time Zone
Easily set by console (or web)
>timezone America/Los_Angeles
Or for the rest of the US (Not the whole list)
America/Phoenix
America/Indiana
America/IndianapolisAmerica/Chicago
America/Los_Angeles
America/Denver
America/Detroit
America/Mexico_CityAmerica/Montreal
America/Vancouver
America/New_York
8/14/2019 Setup of NetApp v1.a1.ppt
27/34
Configure CIFS
deedee*> cifs setup
Enable CIFS access to the filer by a Windows(tm) PC
Your filer is currently only visible to PCs on the same net.
Do you wish to make the system visible via WINS? [no]:
This filer is currently configured as a Multiprotocol filer.
Do you want to configure this filer as a NTFS-only filer? [no]:The default name of this filer will be 'DEEDEE'.
Do you want to modify this name? [no]:
CIFS supports three types of user authentication:
1. Windows Domain authentication.
2. Windows Workgroup authentication using the filer's user accounts.3. /etc/passwd and/or NIS/LDAP based authentication.
What type of authentication will this filer use? [1]: 1
The filer will use Windows Domain authentication.
8/14/2019 Setup of NetApp v1.a1.ppt
28/34
Configure CIFS
Enter the Windows Domain for the filer []:trc.com
TRC.COM is a Windows 2000(tm) domain.
In order to create this filer's domain account, you must supply the
name and password of an administrator account with sufficient privilege
to add the filer to the TRC.COM domain.
Please enter the Windows 2000 user [Administrator@TRC.COM]: administrator@trc.co
m
Password for administrator@trc.com:
CIFS - Logged in as administrator@trc.com.
CIFS - Updating filer account 'cn=deedee,cn=computers,dc=trc,dc=com'
CIFS - Connecting to domain controller.
Sun Feb 23 09:53:53 PST [rc:info]: Starting DC address discovery for TRC.
Sun Feb 23 09:53:58 PST [rc:info]: Found 2 addresses using DNS site query (Defau
lt-First-Site-Name).
Sun Feb 23 09:53:58 PST [rc:info]: Found 3 addresses using generic DNS query.
Sun Feb 23 09:53:58 PST [rc:info]: DC address discovery for TRC complete. 2 uniq
ue addresses found.
Sun Feb 23 09:53:58 PST [rc:info]: Connection with \\W2KDC01 established
Welcome to the TRC (TRC.COM) Windows 2000(tm) domain.
8/14/2019 Setup of NetApp v1.a1.ppt
29/34
Configure CIFS
CIFS local server is running.
deedee*> Sun Feb 23 09:5 4:06 PST [nbns_timer:info]: All CIFS nameregistrations
complete for local server
8/14/2019 Setup of NetApp v1.a1.ppt
30/34
Confirm Available storage
dexter> dfFilesystem kbytes used avail capacity Mounted on/vol/vol0/ 22185864 105868 22079996 0% /vol/vol0//vol/vol0/.snapshot 5546464 0 5546464 0% /vol/vol0/.snapshot
dexter> storage show
Slot: 8aDescription: Fibre Channel Host Adapter 8a (Dual-channel, QLogic 2312 rev. 2)Firmware Rev: 3.1.15PCI Bus Width: 64-bitPCI Clock Speed: 33 MHz
FC Node Name: 2:000:00e08b:09911dCacheline Size: 16FC Packet Size: 2048Link Data Rate: 1 GbitSRAM Parity: YesExternal GBIC: NoState: EnabledIn Use: YesRedundant: Yes
Slot: 8bDescription: Fibre Channel Host Adapter 8b (Dual-channel, QLogic 2312 rev. 2)Firmware Rev: 3.1.15
PCI Bus Width: 64-bitPCI Clock Speed: 33 MHzFC Node Name: 2:001:00e08b:29911dCacheline Size: 16FC Packet Size: 2048Link Data Rate: 1 GbitSRAM Parity: YesExternal GBIC: NoState: EnabledIn Use: YesRedundant: Yes
8/14/2019 Setup of NetApp v1.a1.ppt
31/34
Confirm Available storageSlot: 4aDescription: Fibre Channel Host Adapter 4a (Dual-channel, QLogic 2312 rev. 2)Firmware Rev: 3.1.15PCI Bus Width: 64-bitPCI Clock Speed: 33 MHzFC Node Name: 2:000:00e08b:097d03Cacheline Size: 16FC Packet Size: 2048Link Data Rate: 1 GbitSRAM Parity: YesExternal GBIC: NoState: EnabledIn Use: Yes
Redundant: Yes
Slot: 4bDescription: Fibre Channel Host Adapter 4b (Dual-channel, QLogic 2312 rev. 2)Firmware Rev: 3.1.15PCI Bus Width: 64-bitPCI Clock Speed: 33 MHzFC Node Name: 2:001:00e08b:297d03Cacheline Size: 16FC Packet Size: 2048Link Data Rate: 1 GbitSRAM Parity: YesExternal GBIC: No
State: EnabledIn Use: YesRedundant: Yes
DISK SHELF BAY SERIAL VENDOR MODEL REV--------------------- --------- ---------------- -------- ---------- ----4a.0L0 - - 045150060000 HITACHI OPEN-L 21038a.0L1 - - 045150060001 HITACHI OPEN-L 21038a.0L2 - - 045150060002 HITACHI OPEN-L 21038b.0L0 - - 045150060003 HITACHI OPEN-L 21034b.0L1 - - 045150060004 HITACHI OPEN-L 21034b.0L2 - - 045150060005 HITACHI OPEN-L 2103
8/14/2019 Setup of NetApp v1.a1.ppt
32/34
Appendix BgFiler/Storage Connectivity
Cluster / Direct-Attach 9570V configuration
0A 0B
Filer11A 2B
Filer21A 2B
1A 1B
Up to 84/168 LUNs on eachport (84 per node)
LUN_ownership = high LUN_ownership = low
Host Group 00Port 0A
Host Group 00Port 0B
Host Group 00Port 1A
Host Group 00Port 1B
Controller 0 Controller 19570V
High
High
High
High
Low
Low
Low
Low
8/14/2019 Setup of NetApp v1.a1.ppt
33/34
Appendix BUpgrading the Boot Flash
Upgrading the Boot Flash image for NetApp gFilers Gateways
1) Hitachi Data Systems gets kernel code via FTP from NetworkAppliance:a) ftp ftp.netapp.comb) Login: anonymous
c) Passwd: [your email address]d) bin (change to binary mode)e) cd frm-ntap/HDSf) get netapp_6.4.1-x86g) Save it to some easily-remembered directory on your PC
2) Remove Compact Flash card from gFiler
3) Insert the Compact Flash card into a Compact Flash reader/writer.This piece of equipment can be purchased for about $20.00 from acomputer supply store like Frys, Circuit City or Best Buy.
http://localhost/var/www/Local%20Settings/Temporary%20Internet%20Files/OLK5/ftp.netapp.comhttp://localhost/var/www/Local%20Settings/Temporary%20Internet%20Files/OLK5/ftp.netapp.com8/14/2019 Setup of NetApp v1.a1.ppt
34/34
Appendix B (continued)
4) CD to "X86" folder on the Compact Flash card
5) CD to "KERNEL" folder
6) Remove file called "PRIMARY.KRN"
7) Copy "netapp_6.4.1-x86" from wherever you stored it on your PCto the KERNEL folder and rename it "PRIMARY.KRN"
8) Insert the Compact Flash card into gFiler, button it up, and reboot.
Recommended