View
219
Download
2
Category
Preview:
Citation preview
S-508 USER MANUAL
CATALOGUE1. User instruction2. Software installation3. Connection4. Calibration and commissioning5. Printing and notes6. Maintenance7. After sale service
Please be sure to read following terms and conditions carefully：
1.The machine is used in industries, not toys, should be far away from children. 2.The nozzle of the machine is hot, please do not touch, to avoid the burn. 3. The machine could be used in your countries and regions. It is prohibited to produce objects against the law of your countries and regions. Or all at your own risk. 4. The machine may produce peculiar smell when printing, pls keep the air flowing. You should go to hospital in time, if you feel discomfort. 5. The machine is open source design, modeling and printing tool could be found on the internet. 6.The machine has been tested, suitable for PLA and ABS material, It is prohibited to use other materials. We shall not be liable for any loss causing by using other material. 7.Instructions and warnings will update as required at any time , we have no obligation to inform , please contact us for the latest instructions and warnings . We reserve the right of final interpretation .
USER INSTRUCTION
USER INSTRUCTIONRegarding software installation：Support XP、WIN7、Mac OS WARNING: XP Ghost users may encounter problem connection, flash back, erros, etcIf you want to use XP Ghost, Dandelion version is recommended.Download link：http://www.pgygho.com/xp/Or install “.net framework;” version3.5Download link1：http://www.microsoft.com/zh-cn/download/details.aspx?id=25150Download link2： http://dl.pconline.com.cn/html_2/1/82/id=38126&pn=0&linkPage=1.html
WARNING: Because S508 doesn’t have metal shell, so make sure the plug has the ground wire!
SOFTWARE INSTALLATION
Repetier Host is used for S508 3D printer(0.90C is the latest version, but 0.83 version is recommended if it is your first installation).
0.83
Install 0.90C version or 0.83 version
Double click to install
Choose “English” OK
SOFTWARE INSTALLATION
SOFTWARE INSTALLATION
Choose install path
SOFTWARE INSTALLATION
SOFTWARE INSTALLATION
Start to install Congratulations
OPEN THE SOFTWARE
SOFTWARE INTERFACE
rotateOffsetMove model
DRIVE INSTALLATION
1. Install USB drive first
Printer electrify—connect printer with PC using cable USB.FT232R will not be found the first you use it.
Notes: it will auto-install on Win7 systemXP system
Install device: unzip file we provide you, find the folder “FTDI USB Drivers”
DRIVE INSTALLATION
DRIVE INSTALLATIONChoose this folder
DRIVE INSTALLATION
Notes: Another drive need to be installed after this, find in the same folder.
DRIVE INSTALLATION
After installation, right click “My computer”—”Management”—”Device manager”—”Port”
PLUG-IN INSTALLATION
Two plug-in need to be installed if you use XP system. After installation, restart your PC
Download in Baidu Cloud
Install these two plug-in
PRINTER SETTING
Click here
PRINTER SETTINGPrinter port setting
PRINTER SETTINGTemperature setting
Set temperature according to material ABS or PLA
Reference temp：ABS extruder: 200 hot bed: 80~100PLA extruder: 160 hot bed: 55~60
PRINTER SETTINGPrinting area setting
According to the printer which you buy to choose the printing size Z605:200*200*200mm
CONNECT TO PCFirst, make sure that the machine is correctly assembled, the extruder fan will work after connecting to the electric socket,the red light up.Second, connect printer to computer. Normally, the fan will stop rotating , but will restart about 6 seconds later.
Waiting for the transferring to be completed
It means connection is successful
CONNECTIONTry to move XYZ axis through software, to check the movement direction is correct or not.
Calibration and commissioning1. Manual move X,Y,Z axis, make sure they can move smoot
hly and don’t make noise.
2. Adjust the screw at each corner to make hot bed flat
3. Set the distance between extruder and hot bed the same as the thickness of A4 paper
4. You can print after debugging has completed
PRINTINGLoad files: Choose “file”—”load printing file (must be STL format)”—”convert STL to G code via Slic3r”
PRINTINGParameter setting on SLIC3R: Choose "code generator"- "parameter configuration"
PRINTINGLayer height setting： 0.1 to 0.4, the smaller the layer height is,the more precise will be, but takes more time
PRINTINGFill density and fill pattern setting
PRINTING“√” here to Generate support material
PRINTINGFilament diameter, extruder/hot bed temperature setting
Reference value：
PLA,extruder:160-200， hot bed:50-100ABS,extruder:180-230, hot bed:70-110
PRINTING Size and coordinates setting
PRINTINGNozzle diameter setting: standard is 0.4mm. 0.3 is available also.
Nozzle diameter standard specification:0.4mm,but we customise at 0.3mm
PRINTING
Notes: Remember to SAVE each step after setting.
GENERATE G CODE
1.Click“activate”button, choose “PLA3MM” file
2.Click “start to generate Slic3r”, following dialog box will appear
3.This dialog box will disappear after done
GENERATE G CODE
You can find the G-code on “code editor”
HEAT EXTRUDER and HOT BED
Pre-heat hot bed before generae G code, then heat extruder
RUN
Click “run” when it reaches to specified temp, or wait for generation G-code complete, printer will auto start when it reaches to specified temp
START TO PRINT
You can enjoy your first 3D printing trip, when XYZ axis back to the start NOTICES: Click on run, the machine will heat hot bed to required temp,
Then extruder will be heated, it may take few minutes or longer, please be patient(when hot bed is heated, the red light is bright)
NOTICES
1. PC do not set into energy saving mode, because it may cause failure2. Choose ”Device manager”——“USB controller”——”USB root hub”——right click——click “attributes”——remove the “√ ”
Remove “V”
MAINTENANCE
1.Maintain XYZ bar: If there is noise and unusual shaking during printing, you need to clear the slide bar. The diameter of the slide bar is 8mm, make sure it slides smoothly without any shaking. Lubricating oil can help to clear the slide bar to reduce friction and minimize the wear and between annular tubes and slide bar. 2.Plastic consumables dissolve under high temperatures. And easily plasticize again when cooled. You can use iron wire to drain the nozzle if there is any blockage. We suggest your clear all surplus material after finishing printing work
3D printer does not need special maintenance. It can print for long work hours. Mechanical parts that undergo frequent use will have fair wear and tear.
MAINTENANCE The tension of the strap: strap should fit with the other parts of the machine, to reduce the stress on the motor shaft and pulley. To check if the strap is too tight, turn the pulley and listen for unusually loud sounds, if there are, loosen the strap. To check if the strap is too loose, rotate the motor shaft, it is the correct tension if the hot bed is symmetrical when moving back and forth. It is too loose if the platform takes longer to move back. Another test method is to download cylindrical date. If one side is flat, the corresponding strap is too loose.
AFTER SALE SERVICE Sunhokey Promise: 1.Unconditionally exchange in the receiving 10 days;(Artificial damage except)Guarantee for 2 years.Offer free consultation service for life.2.Maintenance or exchange for free in 10 days to 30 days for 3D printer ,buyer shall bear the freight of depot repair.3.Maintenance or exchange for free in one month to 3 months for 3D printer, buyer shall bear all the freight.4.Within 90 days to 2 years,buyer shall bear all charges for return,exchange and maintenance and freight.
Recommended