QUICK START GUIDE ARTiGO A820 -...

Preview:

Citation preview

QUICK START GUIDE

ARTiGO A820Linux EVK v4.0.1

1.00-08312018-092700

Copyright

Copyright ©2017-2018 VIA Technologies Incorporated. All rights reserved.

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written permission of VIA Technologies, Incorporated.

Trademarks

All brands, product names, company names, trademarks and service marks are the property of their respective holders.

Disclaimer

VIA Technologies makes no warranties, implied or otherwise, in regard to this document and to the products described in this document. The information provided in this document is believed to be accurate and reliable as of the publication date of this document. However, VIA Technologies assumes no responsibility for the use or misuse of the information (including use or connection of extra device/equipment/add-on card) in this document and for any patent infringements that may arise from the use of this document. The information and product specifications within this document are subject to change at any time, without notice and without obligation to notify any person of such change.

VIA Technologies, Inc. reserves the right the make changes to the products described in this manual at any time without prior notice.

Version Date Remarks1.00 08/31/2018 Initial release

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

Revision History

iii

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

Table of Contents1. Introduction ����������������������������������������������������������������������������������������������������������������������� 1

1�1 EVK Package Content ���������������������������������������������������������������������������������������������������������������������������� 11�1�1 Firmware Folder Contents ������������������������������������������������������������������������������������������������������������� 11�1�2 Document Folder Contents ������������������������������������������������������������������������������������������������������������ 11�1�3 Tools Folder Contents �������������������������������������������������������������������������������������������������������������������� 1

1.2 VersionInformationandSupportedFeatures �������������������������������������������������������������������������������������� 2

2. ImageInstallation ������������������������������������������������������������������������������������������������������������� 32.1 BootingfromaMicroSDCard ������������������������������������������������������������������������������������������������������������� 32.2 BootingfromtheSPIROMwitheMMC ������������������������������������������������������������������������������������������������ 4

3. HardwareFunction ����������������������������������������������������������������������������������������������������������� 63.1 SettingUpU-BootParameters ������������������������������������������������������������������������������������������������������������� 63.2 RestoringDefaultU-BootParameters �������������������������������������������������������������������������������������������������� 83.3 UsingtheOpenEmbeddedConsole ������������������������������������������������������������������������������������������������������ 83.4 ConfiguringWatchdogTimer ��������������������������������������������������������������������������������������������������������������� 93.5 SettingUpGPIO ���������������������������������������������������������������������������������������������������������������������������������� 10

3.5.1 SettingUpDIOPortforGPIOFunctionality ��������������������������������������������������������������������������������� 113.5.2 SettingUpGPIMode�������������������������������������������������������������������������������������������������������������������� 113.5.3 SettingUpGPOMode ������������������������������������������������������������������������������������������������������������������ 11

3.6 ConfiguringRTC ���������������������������������������������������������������������������������������������������������������������������������� 12

4� Accessories ���������������������������������������������������������������������������������������������������������������������� 134.1 ConfiguringtheVNT9271USBWi-FiDongle �������������������������������������������������������������������������������������� 134.2 ConfiguringtheEMIO-1541miniPCIeWi-FiModule �������������������������������������������������������������������������� 144.3 ConfiguringtheEMIO-2531miniPCIeUSBWi-Fi&BluetoothModule ���������������������������������������������� 15

4.3.1 ConnectingtotheInternet ���������������������������������������������������������������������������������������������������������� 154.3.2 EnablingBluetooth ���������������������������������������������������������������������������������������������������������������������� 16

4.3.2.1 SettingUpBluetoothA2DPProfile 164.3.2.2 SettingUpBluetoothSPPProfile 17

4.4 ConfiguringtheEMIO-2550miniPCIeMobileBroadbandModule ���������������������������������������������������� 194.4.1 ConnectingtotheInternet ���������������������������������������������������������������������������������������������������������� 194.4.2 EnablingGPS �������������������������������������������������������������������������������������������������������������������������������� 20

iv

1

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

1� IntroductionThisQuickStartGuideprovidesanoverviewofhowtoboottheAndroidEVKsystemimageontheARTiGOA820systemandconfigurethesupportedhardwarefunctioninthebuild.

TheARTiGO-A820LinuxEVKv4.0.1isdevelopedbasedontheNXPfsl-yocto-L4.1.15_1.1.0-ga(Yocto2.0Jethro)andenablesthehardwarefeaturesoftheARTiGOA820system.

1�1 EVK Package ContentTherearethreefoldersinthepackagelistedasbelow.

ARTiGO-A820LinuxEVKcontents

1�1�1 Firmware Folder ContentsARTiGOA920_Yocto2.0_BIN_v4.0.1.tar.gz:containsinstallationscriptfilesandtheprecompiledU-bootandimageforevaluatingtheARTiGO820system.

1�1�2 Document Folder ContentsARTiGO-A820_Linux_BSP_v4.0.1_Quick_Start_Guide_v1.00_20180831.pdf:ThisQuickStartGuideprovidesanoverviewofhowtoboottheAndroidEVKsystemimageontheARTiGOA820systemandconfigurethesupportedhardwarefunctioninthebuild.

1�1�3 Tools Folder ContentsBT_Config.zip:containstheBluetoothA2DPconfiguringfile.

Firmware folder DescriptionARTiGOA820_Yocto2.0_BIN_v4.0.1.tar.gz YoctoEVKsystemimageandinstallation

scriptfilesDocument folder DescriptionARTiGO-A820_Linux_BSP_v4.0.1_Quick_Start_Guide_v1.00_20180831.pdf

QuickStartGuide

Tools folder DescriptionBT_Config.zip BluetoothA2DPconfiguringfile

2

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

1�2 VersionInformationandSupportedFeatures

• U-Bootversion:2015.04

• Kernelversion:4.1.15

• Evaluationimage:OpenEmbedded-corebuiltwithYocto2.0Jethro

• DevelopmentbasedonNXPfsl-yocto-L4.1.15_1.1.0-ga(Yocto2.0Jethro)

• SupportsSPIwitheMMCorMicroSDboot(default)

• SupportsHDMIdisplay

• SupportsHDMIaudiooutput

• SupportsCOM1(RS-232/RS-485),OnboardCOMasdebugport

• SupportsGigabitEthernet(LAN1)

• Supports10/100MpbsEthernet(LAN2)

• SupportsVNT9271USBWi-Fidongle

• SupportsEMIO-1541miniPCIeWi-Fimodule

• SupportsEMIO-2531miniPCIeWi-Fi&BTmodule

º SupportsBluetoothA2DPandSPPprofile

• SupportsEMIO-2550miniPCIeMobileBroadbandmodule

• SupportsWatchdogTimer,GPIOandRTC

3

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

2� ImageInstallationThissectionexplainsthesetuprequirementsforbootingfromaMicroSDcardortheSPIROMandeMMC.

Theinstallationscriptfiles,theprecompiledU-bootandimageareprovidedinthe“Firmware”folder.

2�1 BootingfromaMicroSDCardThefirststepistoinstallthisimageontoaMicroSDcard.InsertaMicroSDcardintoyourLinuxhostmachineandmakesureitisnotmounted.InstalltheSDcardimageontotheMicroSDcardwiththecommandsbelow,replacing<devicename>withthecorrectvalueforthecard.

*Important: Makesureyouarewritingtothecorrectdeviceorthehostsystemenvironmentcouldbedamaged�

Next,ontheARTiGO-A820,setthebootswitchtotheMicroSDpositionasshownbelow.

Micro SD / SPI boot switch diagram

InsertthepreparedMicroSDcardintotheARTiGOA820,connectanHDMIdisplay,andpowerontheARTiGOA820toinitiatethebootprocess.

Whenthebootprocessiscompleted,youwillseetheOpenEmbeddeddesktop.

$ tar xvf ARTiGOA820_Yocto2.0_BIN_v4.0.1.tar.gz$ cd sd_installer/$ sudo ./mk_sd_installer.sh /dev/<device name> --yocto

4

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

2�2 BootingfromtheSPIROMwitheMMCTheARTiGOA820supportsbootingfromtheSPIROMwhileloadingthekernelandrootfilesystemfromeMMC.

ThefirststepistoprepareaMicroSDcardasthesysteminstaller.InsertaMicroSDcardintoyourLinuxhostmachineandmakesureitisnotmounted.InstallthesysteminstallerontotheMicroSDcardwiththecommandbelow,replacing<devicename>withthecorrectvalueforthecard.

Next,ontheARTiGOA820,setthebootswitchtotheMicroSDpositionasshownbelow.

Micro SD / SPI boot switch diagram

InsertthepreparedMicroSDcardintotheARTiGOA820,andpowerontheARTiGOA820.ThesystemwillautomaticallystarttoinstallU-bootandtheimageintoSPIROMandeMMC.

Whentheinstallprocessiscompleted,unplugthepowercableandremovetheMicroSDcard.

$ tar xvf ARTiGOA820_Yocto2.0_BIN_v4.0.1.tar.gz$ cd sd_installer/$ sudo ./mk_sd_installer.sh /dev/<device name>

5

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

Next,inordertobootfromtheSPIROMmakesurethebootswitchissettoSPIROMboot.

MicroSD/SPIbootswitchdiagram

Next,connectanHDMIdisplay,andpoweronthedevicetoinitiatethebootprocess.Whenthebootprocessiscompleted,youwillseetheOpenEmbeddeddesktop.

6

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

3� HardwareFunctionThissectionexplainshowtoenableandtestthehardwarefunctionsprecompiledintheARTiGOA820LinuxEVKincludingsettingU-Bootparameters,configuringWatchdogTimer,settingupGPIO,andconfiguringRTC.

3�1 SettingUpU-BootParametersWhensettinguptheU-Bootparameters,thefirststepistoconnectthehostmachineandtheARTiGOA820throughtheOnboardCOMport.UseaserialportcommunicationprogramsuchasPuTTY,GtkTerm,orMinicomtoconfiguretheserialportsettingandconnecttothedebugconsole.ThereyouwillbeabletoseetheU-BootbootlogandadjustsettingsintheU-Bootconsole.

Serial port setting of host machine

Onboard COM port diagram

7

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

Next,powerontheARTiGOA820toinitiatethebootprocess.Whenprompted,pressanykeytostopthebootprocessandentertheU-Bootconsoleasillustratedbythescreenshotbelow.

Debug console view of boot process

TolistthecurrentU-Bootparameters,usethefollowingcommand:

Tohavemoreinformationmakesuretheprintoutmessageincludes“bootcmd=runbootcmd_auto”.

Thedefault“bootcmd”parameterissettoautodetectthesystemlocationbyfirstattemptingtoloadthekernelfromtheMicroSDcard.IfitisnotdetecteditcontinuestobootfromtheeMMC.

Toloadthekernelfromthespecifieddevice,refertothetwoexamplesbelow.

ToloadthekernelfromtheMicroSDcard,usethefollowingcommand:

ToloadthekernelfromtheeMMC,usethefollowingcommand:

U-Boot 2015.04-imx_v2015.04_4.1.15_1.0.0_ga+gd7d7c43 (Feb 20 2017 – 14:19:23)

CPU: Freescale i.MX6Q rev1.5 at 996 MHzCPU: Temperature 30 CReset cause: PORBoard: MX6DL-VAB820I2C: readyDRAM: 1 GiBMMC: FSL_SDHC: 0, FSL_SDHC: 1SF: Detected W25Q32BV with page size 256 Bytes, erase size

4 KiB, total 4 MiB

No panel detected: default to Hannstar-XGADisplay: Hannstar-XGA (1024x768)In: serialOut: serialErr: serialNet: FEC [PRIME]Warning: failed to set MAC address

Normal BootHit any key to stop autoboot: 0=>

=> printenv

=> setenv bootcmd ‘run bootcmd_sd’=> saveenv=> boot

=> setenv bootcmd ‘run bootcmd_mmc’=> saveenv=> boot

8

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

3�2 RestoringDefaultU-BootParametersIftheU-Bootparametershavebeenmodified,the“destroyenv”commandintheU-Bootconsolecanrestorethefactorydefaultssettings.

Torestartthedevice,usethe“reset”command:

3�3 UsingtheOpenEmbeddedConsoleThefirststepistoconnectthehostmachineandtheARTiGOA820throughtheCOM2port.UseaserialportcommunicationprogramsuchasPuTTY,GtkTerm,orMinicomtoconnecttothedebugconsole.ThereyouwillbeabletoseetheU-BootbootlogandadjustsettingsintheU-Bootconsole.Next,powerontheARTiGO-A820toinitiatethebootprocess.Whenthebootprocessiscompletedyouwillbepromptedtologin.

On board COM port diagram

Thedefaultaccountis“root”,withnopasswordset(justpressEnterwhenpromptedforpassword).

=> destroyenv=> reset

...Freescale i.MX Release Distro 4.1.15_1.1.1 imx6qvab820 /dev/ttymxc1imx6qvab820 login: root

9

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

3�4 ConfiguringWatchdogTimerAWatchdogtimerisanelectronictimerthatisusedtodetectandrecoverfromsystemmalfunctions.

Thewdt_driver_test.outprovidesanapplicationtoconfiguretheWatchdogtimer.

ToenabletheWatchdogwiththedefaulttimeout(60seconds),usethefollowingcommand:

Tochangethetimeout<value>andthesystemreboot<value>(seconds),usethefollowingcommand:

Tosendkeep-aliverequeststotheWatchdog<value>(seconds),usethefollowingcommand:

Whenthevalueof“set_keep_alive”issmallerthanthevalueof“set_timeout”,thesystemwillnotreboot.

TodisabletheWatchdog,usethefollowingcommand:

$ /unit_tests/wdt_driver_test.out enable wdt

$ /unit_tests/wdt_driver_test.out set_timeout <value>

$ /unit_tests/ wdt_driver_test.out set_keep_alive <value>

$ /unit_tests/wdt_driver_test.out disable wdt

10

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

3�5 SettingUpGPIOTheDIOportontheARTiGOA820consistsof9pins.Thefollowingsectionexplainssettingupthesepinsforinput/outputcommunication

DIO port diagram

J7 pin header pinout table

Pin Signal Pin Signal1 RESET_N 2 P_LED+3 GND 4 P_LED-5 I2C3_SCL 6 W_LED+7 I2C3_SDA 8 W_LED-9 5VIN 10 GND

11 GPIO_1 12 GPIO_713 GPIO_2 14 GPIO_815 GPIO_4 16 GPIO_917 GPIO_5 18 GPIO_1619 GND 20

11

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

3�5�1 SettingUpDIOPortforGPIOFunctionalityTheechovalueofGPIOpinsarelistedbelow:

GPIO port pinout table

SetthemultifunctionpinasaGPIOpin.HereistheexampleforGPIOpin1:

3�5�2 SettingUpGPIModeTosetapinto“input”mode(GPI),usethefollowingcommand(hereistheexampleforGPIOpin1):

ToreadtheGPIinputvalue,usethefollowingcommand:

3�5�3 SettingUpGPOModeTosetapinto“output”mode(GPO),usethefollowingcommand(hereistheexampleforGPIOpin1):

Tooutputa“Low”valueontheGPOpin,usethefollowingcommand:

Tooutputa“High”valueontheGPOpin,usethefollowingcommand:

$ echo “in” > /sys/class/gpio/gpio7/direction

$ echo 7 > /sys/class/gpio/export

$ cat /sys/class/gpio/gpio203/value

$ echo “out” > /sys/class/gpio/gpio7/direction

$ echo 1 > /sys/class/gpio/gpio7/value

Pin Signal GPIO echo value1 GPIO_7 72 GPIO_1 13 GPIO_8 84 GPIO_2 25 GPIO_9 96 GPIO_4 47 GPIO_16 2038 GPIO_5 59 GND

$ echo 0 > /sys/class/gpio/gpio7/value

12

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

3�6 ConfiguringRTCTheRTC(Real-TimeClock)keepstrackofthecurrenttimevalues.Thetimevaluesincludetheyear,month,date,hours,minutesandseconds.ToconfiguretheRTContheARTiGOA820,setthesystemtimewiththeLinuxdatecommandasintheexampleshownbelow:

Time value table

Forexample,thevalue061110072013meansJune11201310:07.Thedatecommandalsoacceptsothertimeformats.Formoreinformation,usethefollowingcommand:

TowritethesystemtimetotheRTC,usethefollowingcommand:

ToreadtheRTCtime,usethefollowingcommand:

Time Valuemm 2-digitmonthdd 2-digitdayHH 2-digithoursin24hsystemMM 2-digitminutesYYYY 4-digityear

$ date --help

$ date mmddHHMMYYYY

$ hwclock -w -f /dev/rtc0

$ hwclock -r

13

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

4� AccessoriesThissectionexplainshowtoinstallandconfigurethevariousUSBdongleandminiPCIemodulesavailablefortheARTiGOA820system.

4�1 ConfiguringtheVNT9271USBWi-FiDongle

TheVNT9271USBWi-FidonglesupportsWi-FifunctionalitythroughUSBportconnection.

ThefirststepistoinserttheVNT9271USBWi-FidongleintoaUSBport.Next,makesuretounpluganyLANcablesorotherWi-Fi/3Gmodulesyouhaveinstalled.Finally,powerontheARTiGOA820.

Inserting the VNT9271 USB Wi-Fi dongle

Whenthebootprocessiscompleted,clickonthe“ConnectionManager”icontoconfigureWLAN.

Connection Manager icon diagram

Whentheconnectioniscreated,connecttotheinternetthroughyourwebbrowser.

14

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

4�2 ConfiguringtheEMIO-1541miniPCIeWi-FiModuleTheEMIO-1541modulesupportsWi-FithroughtheonboardminiPCIeslot.

ThefirststepistoinserttheEMIO-1541moduleintotheminiPCIeslot.Afterinstallingthemodule,connecttheprovidedantennatothemodule.Next,makesuretounpluganyLANcablesorUSBWi-Fidonglesyouhaveinstalled.Finally,powerontheARTiGOA820.

Inserting the EMIO-1541 module

Whenthebootprocessiscompleted,clickonthe“Connection Manager”icontoconfigureWLAN.

Connection Manager icon diagram

Whentheconnectioniscreated,connecttotheinternetthroughyourwebbrowser.

15

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

4�3 ConfiguringtheEMIO-2531miniPCIeUSBWi-Fi& BluetoothModuleTheEMIO-2531modulesupportsUSBWi-FiandBluetoothfunctionalitythroughminiPCIeconnections.

4�3�1 ConnectingtotheInternetThefirststepistoinserttheEMIO-2531moduleintotheminiPCIeslot.Afterinstallingeithermoduleconnecttheprovidedantennatothemodule.Next,makesuretounpluganyLANcablesorotherWi-Fi/3Gmodulesyouhaveinstalled.Finally,powerontheARTiGOA820.

Inserting the EMIO-2531 module

Whenthebootprocessiscompleted,clickonthe“Connection Manager”icontoconfigureWLAN.

Connection Manager icon diagram

Whentheconnectioniscreated,connecttotheinternetthroughyourwebbrowser.

16

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

4�3�2 EnablingBluetoothThefollowingsectionexplainssettinguptheAdvancedAudioDistributionProfile(A2DP)andSerialPortProfile(SPP).

4�3�2�1 SettingUpBluetoothA2DPProfileToaddA2DPsupporttotheARTiGOA820,firstcopyandreplacethepulseaudio-system.conf,bluetooth.conf tothe/etc/dbus-1/system.dfolder.Next,copyandreplacethesystem.pafilestothe/etc/pulse/folder.ThesefilesarelocatedintheEVK/BT_ConfigfolderoftheBSP.

ToenabletheBluetoothservice,usethefollowingcommand:

Usethefollowingcommandstorunthe“bluetoothctl”toshowtheBluetoothMACaddressandsetuppairingmodefortheEMIO-2531module.

ToenableBluetoothdevice,usethefollowingcommands:

$ rfkill unblock bluetooth$ hciconfig hci0 up$ hciconfig hci0 piscan$ /usr/lib/bluez5/bluetooth/bluetoothd -C -d &

$ bluetoothctl[NEW] Controller 5C:F3:70:24:4B:2E[bluetooth]#[bluetooth]# showController 5C:F3:70:24:4B:2E Name: BlueZ 5.25 Alias: BlueZ 5.25 …..[bluetooth]# select 5C:F3:70:24:4B:2E[bluetooth]# power onChanging power on succeeded[bluetooth]# agent onAgent registered[bluetooth]# default-agentDefault agent request successful[bluetooth]# discoverable onChanging discoverable on succeeded[CHG] Controller 5C:F3:70:24:4B:2E Discoverable: yes[bluetooth]# pairable onChanging pairable on succeeded[bluetooth]# scan onDiscovery started[CHG] Controller 5C:F3:70:24:4B:2E Discovering: yes[NEW] Device 00:1D:82:BC:C1:C4 Jabra BT-530…[bluetooth]# scan off[bluetooth]# devicesDevice 00:1D:82:BC:C1:C4 Jabra BT-530Device …[bluetooth]# pair 00:1D:82:BC:C1:C4[bluetooth]# trust 00:1D:82:BC:C1:C4

[bluetooth]# connect 00:1D:82:BC:C1:C4[bluetooth]# info 00:1D:82:BC:C1:C4[bluetooth]# quit

17

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

ThedefaultaudiooutputsettingfortheARTiGOA820isHDMIdevice.

Tolistalltheavailableaudiooutputdevices,usethefollowingcommand:

Fromtheoutput,wecanseethefollowing:

• 0=HDMIdevice

• 1=Line-out

• 2=Bluetoothdevice

TosetuptheaudiooutputtoaBluetoothdevice,usethefollowingcommand:

*Note:IfyouwouldliketochangeaudiooutputafterenablingaBluetoothdevice,usethecommandsbelow:

TosetuptheaudiooutputtoLine-out,usethefollowingcommand:

TosetuptheaudiooutputtoHDMIdevice,usethefollowingcommand:

4�3�2�2 SettingUpBluetoothSPPProfileTheARTiGOA820supportsSPPservermodeandSPPclientmode.

ToenabletheBluetoothservice,usethefollowingcommand:

Usethefollowingcommandstorunthe“bluetoothctl”toshowtheBluetoothMACaddressandsetuppairingmodefortheEMIO-2531 module�

$ pactl list short sinks0 alsa_output.platform-sound-hdmi.23.analog-stereo module-alsa-card.c s16le 2ch 48000Hz

SUSPENDED1 alsa_output.platform-sound.22.analog-stereo module-alsa-card.c s16le 2ch 48000Hz

SUSPENDED2 bluez_sink.00_1D_82_BC_C1_C4 module-bluez5-device.c s16le 2ch 48000Hz IDLE

$ pacmd set-default-sink 2

$ pacmd set-default-sink 1

$ pacmd set-default-sink 0

$ rfkill unblock bluetooth$ hciconfig hci0 up$ hciconfig hci0 piscan$ /usr/lib/bluez5/bluetooth/bluetoothd -C -d &

$ bluetoothctl[NEW] Controller 5C:F3:70:24:4B:2E[bluetooth]# scan onDiscovery started[CHG] Controller 5C:F3:70:24:4B:2E Discovering: yes[NEW] Device 5C:F3:70:25:DD:33 BlueZ 5.25…[bluetooth]# scan off[bluetooth]# devicesDevice 5C:F3:70:25:DD:33 BlueZ 5.25Device …[bluetooth]# pair 5C:F3:70:25:DD:33[bluetooth]# trust 5C:F3:70:25:DD:33[bluetooth]# quit

18

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

SPP server mode:

Ifyoudonotchangethelistenchannelnumber,theservicewillautomaticallyusethedefaultchannelnumber.Makesuretheserverorclientmodeisusingthesamebluetoothchannelnumber.

TosetuptheSPPservermodeandallowotherdevicestoconnect,usethefollowingcommands:

SPP client mode:

Ifyoudonotchangethelistenchannelnumber,theservicewillautomaticallyusethedefaultchannelnumber.Makesuretheserverorclientmodeisusingthesamelistenchannelnumber.

UsethefollowingcommandstosetuptheSPPclientmodeandrequestaconnectiontoSPPserver.

UsethefollowingcommandstosetuptheSPPclientmodeandrequestaconnectiontoSPPserver.

Toopentheminicomserialcommunicationprogram,usethefollowingcommand:

Connecttothe/dev/rfcomm0serialdevicewiththefollowingsettings:

Serial port setting of EMIO-2531 module

StartaserialcommunicationprogramonthehostmachinewiththesamecommunicationsettingsusingtheappropriateBluetoothSPPdevice.AfterwardstheBluetoothSPPdeviceandtheARTiGOA820willbeabletocommunicatethroughtheprograms(forexamplesendingakeypressononemachineshouldbeshownontheothermachine).

$ sdptool add SPSerial Port service registered$ rfcomm listen hci0Waiting for connection on channel 1Connection from 5C:F3:70:25:DD:33 to /dev/rfcomm0Press CTRL-C for hangup

$ sdptool add SPSerial Port service registered$ rfcomm connect hci0 5C:F3:70:24:4B:2EConnected /dev/rfcomm0 to 5C:F3:70:24:4B:2E on channel 1Press CTRL-C for hangup

# minicom -s

19

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

4�4 ConfiguringtheEMIO-2550miniPCIeMobileBroadband ModuleTheEMIO-2550miniPCIeMobileBroadbandmodulesupports3GandGPSfunctions.

4�4�1 ConnectingtotheInternetThefirststepistoinsertanactiveSIMcardintotheEMIO-2550module,andtheninserttheEMIO-2550moduleintotheminiPCIeslot.Afterinstallingthemoduleconnecttheprovidedantennatothemodule.Next,makesuretounpluganyLANcablesorUSBWi-Fidonglesyouhaveinstalled.Finally,powerontheARTiGOA820�

Inserting the EMIO-2550 module

TocheckthatthesystemhascorrectlydetectedtheEMIO-2550module,usethefollowingcommand:

Makesuretheprintoutmessageincludes“Bus001Device004:ID1545:1102U-BloxAG”.

Configurethe3GfunctionbycreatingaPPPconnectionwithrootprivilege.

OncethePPPconnectionhasbeencreated,connecttotheinternetthroughyourwebbrowser.

$ lsusb

$ pppd call Module-ZU200

20

ARTiGO A820 Linux EVK v4.0.1 Quick Start Guide

4�4�2 EnablingGPSToconfiguretheGPSfunctionofthemodulerequirestheuseoftheMinicomserialcommunicationprogram.OpentheMinicomserialcommunicationprogramwiththefollowingcommand:

Connecttothe/dev/ttyUSB1serialdevicewiththefollowingsettings:

Serial port setting of EMIO-2550

Whenthesetupiscomplete,typethefollowingGPSATcommandsintoMinicom:AT+UGPRF=1,AT+UGRMC=1,AT+UGGSV=1,AT+UGZDA=1,andAT+UGPS=1,0

Waitforthe“OK”messagebeforesendingthenextATcommand.

UsetheMinicomtosettheserialdevice/dev/ttyUSB7inanotherterminalanditwilloutputthedatareceivedfromtheGPSmoduleasillustratedinthescreenshotbelow.

GPS NMEA message

$ minicom -s

+--------------------------------------------------------------+| A - Serial Device : /dev/ttyUSB1 || B - Lockfile Location : /var/lock || C - Callin Program : || D - Callout Program : || E - Bps/Par/Bits : 115200 8N1 || F - Hardware Flow Control : No || G - Software Flow Control : No |+--------------------------------------------------------------+

AT+UGPRF=1OKAT+UGRMC=1OKAT+UGGSV=1OKAT+UGZDA=1OKAT+UGPS=1,0OK

$GPRMC,142015,00,A,2501.93961,N,12133.66111,E,0.068,,030314,,,A*73$GPGSV,4,1,13,01,34,184,29,03,49,023,47,06,26,042,41,07,44,317,26*75$GPGSV,4,2,13,08,13,323,,11,60,192,,13,29,242,38,16,33,071,16*79$GPGSV,4,3,13,19,65,356,44,23,18,208,12,27,35,034,27,30,37,145,29*7B$GPGSV,4,4,13,32,01,154,*4B$GPZDA,142015.00,03,03,2014,00,00*62

1F, 531 Zhong-zheng Road,Xindian Dist., New Taipei City 231Taiwan

Tel: 886-2-2218-5452Fax: 886-2-2218-9860Email: embedded@via.com.tw

940 Mission CourtFremont, CA 94539,USA

Tel: 1-510-687-4688Fax: 1-510-687-4654Email: embedded@viatech.com

Email: embedded@via-tech.eu

Taiwan Headquarters USA

Europe

Tsinghua Science Park Bldg. 7No. 1 Zongguancun East Road,Haidian Dist., Beijing, 100084China

Tel: 86-10-59852288Fax: 86-10-59852299Email: embedded@viatech.com.cn

3-15-7 Ebisu MT Bldg. 6F,Higashi, Shibuya-kuTokyo 150-0011Japan

Tel: 81-3-5466-1637Fax: 81-3-5466-1638Email: embedded@viatech.co.jp

ChinaJapan

Recommended