View
3
Download
0
Category
Preview:
Citation preview
PV MODULES
LDK SOLAR ENERGYSYSTEMS MODULES
www.ldksolar.com
LIGHT OUR FUTURELIGHT OUR FUTURE
3.0 GWWAFER PRODUCTION
CAPACITY
JIANGXI LDK SOLAR, LTDLDK Avenue, Economic Development Zone, Xinyu, Jiangxi, 338032 P.R. - China
LDK SOLAR HI-TECH (SUZHOU) CO., LTD 6th Floor 1368 Wuzhong Avenue, Wuzhong District, Suzhou City, P.R.China
Tel. +0086.512.82250137 - Fax +0086.512.82250101LDK SOLAR HI-TECH (NANCHANG) SO., LTD.
No.998 TorchS Street, Nanchang City, Jiangxi Province, P.R.China - Tel. 086.791.810 5065 - Fax 0086.791.810 8260LDK SOLAR EUROPE HOLDING S.A
412F Route d'Esch L-2086 - Luxembourg LDK SOLAR USA, INC.
1290 Oakmead Parkway, Suite 306, Sunnyvale, CA 94085 - USA - info.usa@ldksolar.com - Ph. 001.408.2450858 LDK SOLAR GERMANY
Landsberger Strasse 302 80687 Munich - Germany - Ph. +49 (89).90405.276 - info.de@ldksolar.com LDK SOLAR ITALY
Via S. Martino, 25 31020 San Zenone degli Ezzelini, Treviso - Italy - Tel. +39.0423.948833 - info.it@ldksolar.comVia Giulio Cesare Procaccini, 48 20154 Milano - Italy - Tel. +39.02.87242050
LDK SOLAR FRANCEhugh.harris@ldksolar.com - Ph. +33.619.606288
LDK SOLAR SPAINoscar.artal@ldksolar.com - Ph. +34.672.074200
LDK SOLARTHE WORLD’S LARGEST VERTICALLY INTEGRATED MANUFACTURER
LIGHT OUR FUTURE
BEST IN CLASSTECHNOLOGYAND COST EFFECTIVE
INTRODUCTION
POLYSILICON:11.000 MT TODAY25.000 MT BY END OF 2011
INGOTS/WAFER:3.0 GW TODAY4.0 GW END OF 2011
MODULES:1.5 GW TODAY2.5 GW END OF 2011
CELLS:180 MW TODAY1.26 GW BY END OF 2011
LDK Solar at NYSE
June 2007
LDK SOLARTHE WORLD’S LARGEST VERTICALLY INTEGRATED MANUFACTURER
LIGHT OUR FUTURE
BEST IN CLASSTECHNOLOGYAND COST EFFECTIVE
INTRODUCTION
POLYSILICON:11.000 MT TODAY25.000 MT BY END OF 2011
INGOTS/WAFER:3.0 GW TODAY4.0 GW END OF 2011
MODULES:1.5 GW TODAY2.5 GW END OF 2011
CELLS:180 MW TODAY1.26 GW BY END OF 2011
LDK Solar at NYSE
June 2007
LDK’s ATTRACTIVE GROWTH STRATEGIES
IN-HOUSEPRODUCTION
IN-HOUSE IN-HOUSE IN-HOUSE& OEM
IN-HOUSE
PROVEN COST REDUCTION ROAD MAP
VERTICAL INTEGRATION
LIGHT OUR FUTURE
2 GWVERTICALINTEGRATION
ECOMOMIESOF SCALE & RAPIDGROWTH
COMPETITIVECOST STRUCTURE
HIGH QUALITYHIGH EFFICIENCYPRODUCTS
GRID PARITYLDK SOLAR
Produces solar and semiconductor grade polysilicon and chemicals
11.000 MT capacity today
25.000 MT capacity by end of 2011
Multi - and mono-crystalline ingoting capabilities
3.0 GW capacity today
4.0 GW capacity by end of 2011
World’s largest wafering company
3.0 GW capacity today
4.0 GW capacity by end of 2011
R&D and investment in process
180 MW capacity today
1.26 GW capacity by end of 2011
Acquired best solar module capacity
1.5 GW capacity today
2.5 GW capacity by end of 2011
FORMULA GRID PARITY
LDK Silicon LDK Ingots LDK Wafer LDK Cells LDK Module
++
+=
Multi
Mono
Multi
Mono
Multi
Mono
Multi
Mono
LDK’s ATTRACTIVE GROWTH STRATEGIES
IN-HOUSEPRODUCTION
IN-HOUSE IN-HOUSE IN-HOUSE& OEM
IN-HOUSE
PROVEN COST REDUCTION ROAD MAP
VERTICAL INTEGRATION
LIGHT OUR FUTURE
2 GWVERTICALINTEGRATION
ECOMOMIESOF SCALE & RAPIDGROWTH
COMPETITIVECOST STRUCTURE
HIGH QUALITYHIGH EFFICIENCYPRODUCTS
GRID PARITYLDK SOLAR
Produces solar and semiconductor grade polysilicon and chemicals
11.000 MT capacity today
25.000 MT capacity by end of 2011
Multi - and mono-crystalline ingoting capabilities
3.0 GW capacity today
4.0 GW capacity by end of 2011
World’s largest wafering company
3.0 GW capacity today
4.0 GW capacity by end of 2011
R&D and investment in process
180 MW capacity today
1.26 GW capacity by end of 2011
Acquired best solar module capacity
1.5 GW capacity today
2.5 GW capacity by end of 2011
FORMULA GRID PARITY
LDK Silicon LDK Ingots LDK Wafer LDK Cells LDK Module
++
+=
Multi
Mono
Multi
Mono
Multi
Mono
Multi
Mono
LDK POLYSILICON
As part of our vertical integration strategy, LDK Solar constructed a polysilicon plant with two production facilities near our wafer production facilities. The first facility has a
planned installed annualized production capacity of 3.000 metric-ton. The second facility has three separate trains, each with a planned 5.000-metric-ton annualized
production capacity. The installation of a closed-loop production process has been completed in both facilities. Our closed-loop polysilicon production
process is designed so that LDK Solar is able to produce and use many of the key chemicals and gases required to make silicon, such as
TCS, HCI and hydrogen, while also recycling the residual STC.
LDK POLYSILICON
THE WORLD’S LARGESTSINGLE POLYSILICONPLANT SITE
LIGHT OUR FUTURE
TECHNICAL SPECIFICATION 11N
Semi-conductor
Grade
Solar Grade
> 300
> 50
> 3000
> 500
> 1.5x1E16
> 2.5x1E16
SiliconGrade
N-TypeResistivity(u.cm)
P-TypeResistivity(u.cm)
CarbonContent(atoms/cm3)
11.000 MTtoday
LDK POLYSILICON
As part of our vertical integration strategy, LDK Solar constructed a polysilicon plant with two production facilities near our wafer production facilities. The first facility has a
planned installed annualized production capacity of 3.000 metric-ton. The second facility has three separate trains, each with a planned 5.000-metric-ton annualized
production capacity. The installation of a closed-loop production process has been completed in both facilities. Our closed-loop polysilicon production
process is designed so that LDK Solar is able to produce and use many of the key chemicals and gases required to make silicon, such as
TCS, HCI and hydrogen, while also recycling the residual STC.
LDK POLYSILICON
THE WORLD’S LARGESTSINGLE POLYSILICONPLANT SITE
LIGHT OUR FUTURE
TECHNICAL SPECIFICATION 11N
Semi-conductor
Grade
Solar Grade
> 300
> 50
> 3000
> 500
> 1.5x1E16
> 2.5x1E16
SiliconGrade
N-TypeResistivity(u.cm)
P-TypeResistivity(u.cm)
CarbonContent(atoms/cm3)
11.000 MTtoday
LDK INGOTS
LARGER INGOTS PRODUCTIONMEANS COSTS REDUCTION
LDK INGOTS
THE LARGEST MULTICRYSTALLINEWAFER PROVIDER IN THE WORLD
LDK WAFERS
At LDK Solar, we produce larger monocrystalline and multicrystalline ingots. This innovation enables us to increase
our yield of ingots and increase the utilization rates of our facilities thus reducing costs by reaching economies of
scale. For example, LDK Solar produced multicrystalline ingot weight of 800 kg which will
increase throughput production efficiencies by reducing manufacturing bottlenecks. Our
ingot manufacturing facilities are located in Xinyu City in Jiangxi province in China
LDK WAFERS As the largest multicrystalline wafer provider in the world, LDK
Solar has an established track record of consistently deliveringhigh quality solar wafers to our valued customers. We take
pride in providing technologically advanced and reliablesolar wafers. At LDK Solar, we utilize state-of-the-art
wafer processing equipment combined withproprietary know-how that enables us to make
efficient use of polysilicon and thereforelower the costs. Our wafer manufacturing
facilities are located in Xinyu City inJiangxi province in China.
MultiMono
Multi
Mono
3.0 GWtoday 3.0 GW
todaty
LDK INGOTS
LARGER INGOTS PRODUCTIONMEANS COSTS REDUCTION
LDK INGOTS
THE LARGEST MULTICRYSTALLINEWAFER PROVIDER IN THE WORLD
LDK WAFERS
At LDK Solar, we produce larger monocrystalline and multicrystalline ingots. This innovation enables us to increase
our yield of ingots and increase the utilization rates of our facilities thus reducing costs by reaching economies of
scale. For example, LDK Solar produced multicrystalline ingot weight of 800 kg which will
increase throughput production efficiencies by reducing manufacturing bottlenecks. Our
ingot manufacturing facilities are located in Xinyu City in Jiangxi province in China
LDK WAFERS As the largest multicrystalline wafer provider in the world, LDK
Solar has an established track record of consistently deliveringhigh quality solar wafers to our valued customers. We take
pride in providing technologically advanced and reliablesolar wafers. At LDK Solar, we utilize state-of-the-art
wafer processing equipment combined withproprietary know-how that enables us to make
efficient use of polysilicon and thereforelower the costs. Our wafer manufacturing
facilities are located in Xinyu City inJiangxi province in China.
MultiMono
Multi
Mono
3.0 GWtoday 3.0 GW
todaty
LDK CELLS
• Vertically integrated manufacturing• Large scale production facilities
• Proven low-cost manufacturing• High-quality, high-efficiency products
• Leading global wafer supplier• Diversified global customer base
IN-HOUSE MANUFACTURINGOF PV CELLS
LDK MODULES
MAKING SOLARENERGY ACCESSIBLEFOR EVERYONE
600 MWApril 2010
1.5 GWToday
2.5 GWBy the end of 2011
CAPACITY:
LDK CELLSManufacturing in-house PV cells and increasing the efficiency of
solar cells is one of the most effective drivers to reduce the cost of PV modules. We are currently in the process to
complete our cell manufacturing lines to produce our own cells in-house as well as working on developing
new high-efficiency monocrystalline and multicrystalline cell technology. Manufacturing
our own cells in-house will reduce the cost of modules, increase quality managament,
and ensure a stable supply of cells.
Multi
Mono
Multi
Mono
LDK SOLAR MODULES180 MW
today
1.5 GWtoday
LDK CELLS
• Vertically integrated manufacturing• Large scale production facilities
• Proven low-cost manufacturing• High-quality, high-efficiency products
• Leading global wafer supplier• Diversified global customer base
IN-HOUSE MANUFACTURINGOF PV CELLS
LDK MODULES
MAKING SOLARENERGY ACCESSIBLEFOR EVERYONE
600 MWApril 2010
1.5 GWToday
2.5 GWBy the end of 2011
CAPACITY:
LDK CELLSManufacturing in-house PV cells and increasing the efficiency of
solar cells is one of the most effective drivers to reduce the cost of PV modules. We are currently in the process to
complete our cell manufacturing lines to produce our own cells in-house as well as working on developing
new high-efficiency monocrystalline and multicrystalline cell technology. Manufacturing
our own cells in-house will reduce the cost of modules, increase quality managament,
and ensure a stable supply of cells.
Multi
Mono
Multi
Mono
LDK SOLAR MODULES180 MW
today
1.5 GWtoday
Manufactured under stringent quality contract standards:
MODULES:RELIABLE MODULESFOR CUSTOMERS
MODULES
MODULEQUALITY
One of the most comprehensive warranties in the solar industry:MODULE
WARRANTY
Banking institutions want protection guarantees on their investments as part of a debt financing package:MODULE
INSURANCE
MUNICH-RE INSURANCE
Since beginning of 2010 LDK Solar is proud member of PV Cycle OrganizationMODULE
RECYCLING
Manufactured under stringent quality contract standards:
MODULES:RELIABLE MODULESFOR CUSTOMERS
MODULES
MODULEQUALITY
One of the most comprehensive warranties in the solar industry:MODULE
WARRANTY
Banking institutions want protection guarantees on their investments as part of a debt financing package:MODULE
INSURANCE
MUNICH-RE INSURANCE
Since beginning of 2010 LDK Solar is proud member of PV Cycle OrganizationMODULE
RECYCLING
160D-165D-170D-175D-180D-185D-190D-195D-200D-24 (S)NEW DIMENSIONS
MONOCRYSTALLINE MODULES
WHY LDK SOLAR MODULES
TYPENominal Output (Pmax) [W] Voltage at Pmax (Vmp) [V]Current at Pmax (Imp) [A]Open Circuit Voltage (Voc) [V]Short Circuit Current (Isc)The power tolerance is +/- 3% referred to the Nominal OutputMaximum System VoltageCell EfficiencyModule Efficiency
ELECTRIC CHARACTERISTICS (STC*)
STC* (Standard Test Conditions): Irradiance 1000W/m2, Module Temperature 25°C, Air Mass 1.5
IEC: 1000V / UL: 600 V
TYPENominal Output (Pmax) Voltage at Pmax (Vmp) Current at Pmax (Imp)Open Circuit Voltage (Voc)Short Circuit Current (Isc)
ELECTRICAL PERFORMANCE AT NOCT
NOCT: Irradiance 800 W/m2, Module Temperature 45± 2°C, Air Mass 1.5
DIMENSIONS PERFORMANCE AT LOW IRRADIANCE
• Industry leading module power output warranty• International quality, safety and performance certifications• Modules manufactured at ISO 9001 certified factories• High-reliability with guaranteed 0/+5W peak power classification
WARRANTIES• 5 years for product defects in materials & workmanship• 12 years for 90% of warranted minimum power• 25 years for 80% of warranted minimum power
CERTIFICATES• IEC: IEC 61215, IEC 61730 (1&2), conformity to CE• UL1703 2002/03/15 Ed:3 Rev: 2004/06/30• ULC/ORD-C1703-01 second edition 2001/01/01• UL and Canadian standard for safety flat-plate
• ISO9001:2008 Quality Management System• CEC Listed: modules are elegible for California rebates• PV Cycle: voluntary module take back and recycling program
TYPENOCT** Temperature Coefficient of PmaxTemperature Coefficient of VocTemperature Coefficient of IscMaximum Series Fuse RatingOperating TemperatureStorage Temperature
TEMPERATURE CHARACTERISTICS
NOCT**: Nominal Operation Cell Temperature Sun 800 W/m2; Air 20°C; wind speed 1m/s
45±2°C-0.47% / °C-0.34% / °C0.06% / °C
10 A-40 to +85°C-40 to +60°C
LDK-D-24 Series (s)
TYPEPacking ConfigurationQuantity/PalletLoading Capacity
PACKING CONFIGURATION
25 pcs./box 50 pcs./pallet
700 pcs. / 40 ft (H)
LDK-D-24 Series (s)
TYPESolar CellsFront CoverBack CoverEncapsulantFrameDiodesJunction BoxConnectorCablesDimensionWeightMax. Load
MECHANICAL CHARACTERISTICS
72 (6x12) monocrystalline silicon solar cells 125 x 125 mm3.2 mm thick, Tempered glass / AR coating glass
TPT (Tedlar-PET-Tedlar) / BBFEVA (Ethylene vinyl acetate)
Anodized aluminium alloy, double wall6 Bypass diodes serviceable
IP65 ratedMC4 or compatible connector
Lenght: 950 mm / Section: 4.0 mm2
1580 x 808 x 40 mm / 62.4 x 31.8 x 1.6 inches (new dimensions)15.6 kg / 34.4 lbs
Wind Load: 2400Pa / Snow Load: 5400 Pa
LDK-D-24 Series (s)
LDK Solar reserves the right to make specifications changes without any prior notice. This data sheet complies with the EN 50380 requirement. January 2011/V1/ ©LDK Solar Limited. All rights reserved. E.&O.E.
www.ldksolar.com module.sales@ldksolar.com
LIGHT OUR FUTURE
40
950
808770
800
50
50
30
30
140
390
808
1580
4-10×10Drainage holes
4 places
8-8x3Drainage holes
8 placesJunction box
8-14x9Mounting slots
8 places
2-Ø4Ground holes
2 places
1300
1580
The typical relative change in module efficiency at an irradiance of 200W/m² in relation to 1000W/m²(both at 25°C and AM 1.5 spectrum) is less than 6%
1.05
2)
1
0.95
0.9
0.85
0.8200 300 400 500 600 700 800 900 1000
IV CURVE AT DIFFERENT IRRADIANCE LEVELS
0
1
2
3
4
5
6
0 5 10 15 20 25 30 35 40 45 50Voltage / V
Cur
rent
/ A
Rel
ativ
e Ef
ficie
ncy
1000W/m²
800W/m²
600W/m²
400W/m²
200W/m²
Above graphics according to LDK-175D-24(s)
16035.04.644.05.38
15.3712.53
160D-24(s)
11629.83.8940.54.36
16535.24.6844.25.40
15.8512.92
165D-24(s)
12030.73.9140.74.37
17035.44.7644.55.42
16.3313.32
170D-24(s)
12331.33.9341.04.39
17535.94.8744.75.43
16.8113.71
175D-24(s)
12732.33.9441.24.40
18036.24.9844.95.46
17.2814.10
180D-24(s)
13032.83.9641.34.42
18536.95.0245.15.48
17.7714.49
185D-24(s)
13433.63.9841.54.44
19037.75.0545.25.51
18.2514.88
190D-24(s)
13834.63.9941.64.46
19537.95.1645.35.54
18.7315.27
195D-24(s)
14235.54.0141.84.48
20038.15.2745.45.57
19.2115.67
200D-24(s)
160D-24(s) 165D-24(s) 170D-24(s) 175D-24(s) 180D-24(s) 185D-24(s) 190D-24(s) 195D-24(s) 200D-24(s)
14636.44.0342
4.50
Tolerance of length and width dimensions is ± 2 mm
160D-165D-170D-175D-180D-185D-190D-195D-200D-24 (S)NEW DIMENSIONS
MONOCRYSTALLINE MODULES
WHY LDK SOLAR MODULES
TYPENominal Output (Pmax) [W] Voltage at Pmax (Vmp) [V]Current at Pmax (Imp) [A]Open Circuit Voltage (Voc) [V]Short Circuit Current (Isc)The power tolerance is +/- 3% referred to the Nominal OutputMaximum System VoltageCell EfficiencyModule Efficiency
ELECTRIC CHARACTERISTICS (STC*)
STC* (Standard Test Conditions): Irradiance 1000W/m2, Module Temperature 25°C, Air Mass 1.5
IEC: 1000V / UL: 600 V
TYPENominal Output (Pmax) Voltage at Pmax (Vmp) Current at Pmax (Imp)Open Circuit Voltage (Voc)Short Circuit Current (Isc)
ELECTRICAL PERFORMANCE AT NOCT
NOCT: Irradiance 800 W/m2, Module Temperature 45± 2°C, Air Mass 1.5
DIMENSIONS PERFORMANCE AT LOW IRRADIANCE
• Industry leading module power output warranty• International quality, safety and performance certifications• Modules manufactured at ISO 9001 certified factories• High-reliability with guaranteed 0/+5W peak power classification
WARRANTIES• 5 years for product defects in materials & workmanship• 12 years for 90% of warranted minimum power• 25 years for 80% of warranted minimum power
CERTIFICATES• IEC: IEC 61215, IEC 61730 (1&2), conformity to CE• UL1703 2002/03/15 Ed:3 Rev: 2004/06/30• ULC/ORD-C1703-01 second edition 2001/01/01• UL and Canadian standard for safety flat-plate
• ISO9001:2008 Quality Management System• CEC Listed: modules are elegible for California rebates• PV Cycle: voluntary module take back and recycling program
TYPENOCT** Temperature Coefficient of PmaxTemperature Coefficient of VocTemperature Coefficient of IscMaximum Series Fuse RatingOperating TemperatureStorage Temperature
TEMPERATURE CHARACTERISTICS
NOCT**: Nominal Operation Cell Temperature Sun 800 W/m2; Air 20°C; wind speed 1m/s
45±2°C-0.47% / °C-0.34% / °C0.06% / °C
10 A-40 to +85°C-40 to +60°C
LDK-D-24 Series (s)
TYPEPacking ConfigurationQuantity/PalletLoading Capacity
PACKING CONFIGURATION
25 pcs./box 50 pcs./pallet
700 pcs. / 40 ft (H)
LDK-D-24 Series (s)
TYPESolar CellsFront CoverBack CoverEncapsulantFrameDiodesJunction BoxConnectorCablesDimensionWeightMax. Load
MECHANICAL CHARACTERISTICS
72 (6x12) monocrystalline silicon solar cells 125 x 125 mm3.2 mm thick, Tempered glass / AR coating glass
TPT (Tedlar-PET-Tedlar) / BBFEVA (Ethylene vinyl acetate)
Anodized aluminium alloy, double wall6 Bypass diodes serviceable
IP65 ratedMC4 or compatible connector
Lenght: 950 mm / Section: 4.0 mm2
1580 x 808 x 40 mm / 62.4 x 31.8 x 1.6 inches (new dimensions)15.6 kg / 34.4 lbs
Wind Load: 2400Pa / Snow Load: 5400 Pa
LDK-D-24 Series (s)
LDK Solar reserves the right to make specifications changes without any prior notice. This data sheet complies with the EN 50380 requirement. January 2011/V1/ ©LDK Solar Limited. All rights reserved. E.&O.E.
www.ldksolar.com module.sales@ldksolar.com
LIGHT OUR FUTURE
40
950
808770
800
50
50
30
30
140
390
808
1580
4-10×10Drainage holes
4 places
8-8x3Drainage holes
8 placesJunction box
8-14x9Mounting slots
8 places
2-Ø4Ground holes
2 places
1300
1580
The typical relative change in module efficiency at an irradiance of 200W/m² in relation to 1000W/m²(both at 25°C and AM 1.5 spectrum) is less than 6%
1.05
2)
1
0.95
0.9
0.85
0.8200 300 400 500 600 700 800 900 1000
IV CURVE AT DIFFERENT IRRADIANCE LEVELS
0
1
2
3
4
5
6
0 5 10 15 20 25 30 35 40 45 50Voltage / V
Cur
rent
/ A
Rel
ativ
e Ef
ficie
ncy
1000W/m²
800W/m²
600W/m²
400W/m²
200W/m²
Above graphics according to LDK-175D-24(s)
16035.04.6
44.05.38
15.3712.53
160D-24(s)
11629.83.8940.54.36
16535.24.6844.25.40
15.8512.92
165D-24(s)
12030.73.9140.74.37
17035.44.7644.55.42
16.3313.32
170D-24(s)
12331.33.9341.04.39
17535.94.8744.75.43
16.8113.71
175D-24(s)
12732.33.9441.24.40
18036.24.9844.95.46
17.2814.10
180D-24(s)
13032.83.9641.34.42
18536.95.0245.15.48
17.7714.49
185D-24(s)
13433.63.9841.54.44
19037.75.0545.25.51
18.2514.88
190D-24(s)
13834.63.9941.64.46
19537.95.1645.35.54
18.7315.27
195D-24(s)
14235.54.0141.84.48
20038.15.2745.45.57
19.2115.67
200D-24(s)
160D-24(s) 165D-24(s) 170D-24(s) 175D-24(s) 180D-24(s) 185D-24(s) 190D-24(s) 195D-24(s) 200D-24(s)
14636.44.0342
4.50
Tolerance of length and width dimensions is ± 2 mm
TYPENominal Output (Pmax) [W] Voltage at Pmax (Vmp) [V]Current at Pmax (Imp) [A]Open Circuit Voltage (Voc) [V]Short Circuit Current (Isc)The power tolerance is +/- 3% referred to the Nominal OutputMaximum System VoltageCell EfficiencyModule Efficiency
ELECTRIC CHARACTERISTICS (STC*)
STC* (Standard Test Conditions): Irradiance 1000W/m2, Module Temperature 25°C, Air Mass 1.5
IEC: 1000V / UL: 600 V
TYPENominal Output (Pmax) Voltage at Pmax (Vmp) Current at Pmax (Imp)Open Circuit Voltage (Voc)Short Circuit Current (Isc)
ELECTRICAL PERFORMANCE AT NOCT
NOCT: Irradiance 800 W/m2, Module Temperature 45± 2°C, Air Mass 1.5
TYPENOCT** Temperature Coefficient of PmaxTemperature Coefficient of VocTemperature Coefficient of IscMaximum Series Fuse RatingOperating TemperatureStorage Temperature
TEMPERATURE CHARACTERISTICS
NOCT**: Nominal Operation Cell Temperature Sun 800 W/m2; Air 20°C; wind speed 1m/s
45±2°C-0.47% / °C-0.34% / °C0.06% / °C
12 A-40 to +85°C-40 to +60°C
LDK-D-20 Series (s)
TYPEPacking ConfigurationQuantity/PalletLoading Capacity
PACKING CONFIGURATION
25 pcs./box 50 pcs./pallet
700 pcs. / 40 ft (H)
LDK-D-20 Series (s)
TYPESolar CellsFront CoverBack CoverEncapsulantFrameDiodesJunction BoxConnectorCablesDimensionWeightMax. Load
MECHANICAL CHARACTERISTICS
(6x10) monocrystalline silicon solar cells 156 x 156 mm3.2 mm thick, Tempered glass / AR coating glass
TPT (Tedlar-PET-Tedlar) / BBFEVA (Ethylene vinyl acetate)
Anodized aluminium alloy, double wall6 Bypass diodes serviceable
IP65 ratedMC4 or compatible connector
Lenght: 1000 mm / Section: 4.0 mm2
1630 x 976 x 40 mm / 64.2 x 38.4x 1.6 inches (new dimensions)20 kg / 44.1 lbs
Wind Load: 2400Pa / Snow Load: 5400 Pa
LDK-D-20 Series (s)
LDK Solar reserves the right to make specifications changes without any prior notice. This data sheet complies with the EN 50380 requirement. January 2011/V1/ ©LDK Solar Limited. All rights reserved. E.&O.E.
20029.56.7836.17.68
14.3712.57
200D-20(s)
14525.35.7433.26.22
20529.76.9136.47.73
14.7412.89
205D-20(s)
14925.85.7833.56.26
21029.97.0236.67.78
15.0913.20
210D-20(s)
15226.15.8433.76.30
21530.67.0336.77.90
15.4613.51
215D-20(s)
15626.35.9333.86.40
22031.27.0536.98.01
15.8113.83
220D-20(s)
15926.56.0134.06.48
22531.57.1537.08.11
16.1814.14
225D-20(s)
16326.86.0934.16.57
23031.87.2337.28.21
16.5614.46
230D-20(s)
16727.16.1634.36.65
23532.07.3537.28.30
16.9014.77
235D-20(s)
17027.36.2334.36.72
24032.27.4537.38.39
17.2515.09
240D-20(s)
17427.76.2834.36.79
24532.47.5637.48.48
17.5115.40
245D-20(s)
17828.06.3634.46.87
25032.67.6737.58.57
17.9315.71
250D-20(s)
200D-20(s) 205D-20(s) 210D-20(s) 215D-20(s) 220D-20(s) 225D-20(s) 230D-20(s) 235D-20(s) 240D-20(s) 245D-20(s) 250D-20(s)
18128.26.4134.56.94
200D-205D-210D-215D-220D-225-230D-240D-245D-250D-20 (S)NEW DIMENSIONS
MONOCRYSTALLINE MODULES
WHY LDK SOLAR MODULES
DIMENSIONS PERFORMANCE AT LOW IRRADIANCE
• Industry leading module power output warranty• International quality, safety and performance certifications• Modules manufactured at ISO 9001 certified factories• High-reliability with guaranteed 0/+5W peak power classification• Module performance reinsurance policy (Munich RE)
WARRANTIES• 5 years for product defects in materials & workmanship• 12 years for 90% of warranted minimum power• 25 years for 80% of warranted minimum power
CERTIFICATES• IEC: IEC 61215, IEC 61730 (1&2), conformity to CE• UL1703 2002/03/15 Ed:3 Rev: 2004/06/30• ULC/ORD-C1703-01 second edition 2001/01/01• UL and Canadian standard for safety flat-plate
• ISO9001:2008 Quality Management System• CEC Listed: modules are elegible for California rebates• PV Cycle: voluntary module take back and recycling program
www.ldksolar.com module.sales@ldksolar.com
LIGHT OUR FUTURE
The typical relative change in module efficiency at an irradiance of 200W/m² in relation to 1000W/m²(both at 25°C and AM 1.5 spectrum) is less than 6%
1.05
2)
1
0.95
0.9
0.85
0.8200 300 400 500 600 700 800 900 1000
IV CURVE AT DIFFERENT IRRADIANCE LEVELS
0
1
2
4
3
6
5
0 5 10 15 20 25 30 35 40 45 50Voltage / V
Cur
rent
/ A
Rel
ativ
e Ef
ficie
ncy
1000W/m²
800W/m²
600W/m²
400W/m²
200W/m²
Above graphics according to LDK-220D-20(s)
4-10×10Drainage holes
4 places
8-8x3Drainage holes
8 places
Junction box
8-14x9Mounting slots
8 places
2-Ø4Ground holes
2 places
40
1000
976938
1630
1300
800
50
5030
3016
541
5
1630
976
Tolerance of length and width dimensions is ± 2 mm
TYPENominal Output (Pmax) [W] Voltage at Pmax (Vmp) [V]Current at Pmax (Imp) [A]Open Circuit Voltage (Voc) [V]Short Circuit Current (Isc)The power tolerance is +/- 3% referred to the Nominal OutputMaximum System VoltageCell EfficiencyModule Efficiency
ELECTRIC CHARACTERISTICS (STC*)
STC* (Standard Test Conditions): Irradiance 1000W/m2, Module Temperature 25°C, Air Mass 1.5
IEC: 1000V / UL: 600 V
TYPENominal Output (Pmax) Voltage at Pmax (Vmp) Current at Pmax (Imp)Open Circuit Voltage (Voc)Short Circuit Current (Isc)
ELECTRICAL PERFORMANCE AT NOCT
NOCT: Irradiance 800 W/m2, Module Temperature 45± 2°C, Air Mass 1.5
TYPENOCT** Temperature Coefficient of PmaxTemperature Coefficient of VocTemperature Coefficient of IscMaximum Series Fuse RatingOperating TemperatureStorage Temperature
TEMPERATURE CHARACTERISTICS
NOCT**: Nominal Operation Cell Temperature Sun 800 W/m2; Air 20°C; wind speed 1m/s
45±2°C-0.47% / °C-0.34% / °C0.06% / °C
12 A-40 to +85°C-40 to +60°C
LDK-D-20 Series (s)
TYPEPacking ConfigurationQuantity/PalletLoading Capacity
PACKING CONFIGURATION
25 pcs./box 50 pcs./pallet
700 pcs. / 40 ft (H)
LDK-D-20 Series (s)
TYPESolar CellsFront CoverBack CoverEncapsulantFrameDiodesJunction BoxConnectorCablesDimensionWeightMax. Load
MECHANICAL CHARACTERISTICS
(6x10) monocrystalline silicon solar cells 156 x 156 mm3.2 mm thick, Tempered glass / AR coating glass
TPT (Tedlar-PET-Tedlar) / BBFEVA (Ethylene vinyl acetate)
Anodized aluminium alloy, double wall6 Bypass diodes serviceable
IP65 ratedMC4 or compatible connector
Lenght: 1000 mm / Section: 4.0 mm2
1630 x 976 x 40 mm / 64.2 x 38.4x 1.6 inches (new dimensions)20 kg / 44.1 lbs
Wind Load: 2400Pa / Snow Load: 5400 Pa
LDK-D-20 Series (s)
LDK Solar reserves the right to make specifications changes without any prior notice. This data sheet complies with the EN 50380 requirement. January 2011/V1/ ©LDK Solar Limited. All rights reserved. E.&O.E.
20029.56.7836.17.68
14.3712.57
200D-20(s)
14525.35.7433.26.22
20529.76.9136.47.73
14.7412.89
205D-20(s)
14925.85.7833.56.26
21029.97.0236.67.78
15.0913.20
210D-20(s)
15226.15.8433.76.30
21530.67.0336.77.90
15.4613.51
215D-20(s)
15626.35.9333.86.40
22031.27.0536.98.01
15.8113.83
220D-20(s)
15926.56.0134.06.48
22531.57.1537.08.11
16.1814.14
225D-20(s)
16326.86.0934.16.57
23031.87.2337.28.21
16.5614.46
230D-20(s)
16727.16.1634.36.65
23532.07.3537.28.30
16.9014.77
235D-20(s)
17027.36.2334.36.72
24032.27.4537.38.39
17.2515.09
240D-20(s)
17427.76.2834.36.79
24532.47.5637.48.48
17.5115.40
245D-20(s)
17828.06.3634.46.87
25032.67.6737.58.57
17.9315.71
250D-20(s)
200D-20(s) 205D-20(s) 210D-20(s) 215D-20(s) 220D-20(s) 225D-20(s) 230D-20(s) 235D-20(s) 240D-20(s) 245D-20(s) 250D-20(s)
18128.26.4134.56.94
200D-205D-210D-215D-220D-225-230D-240D-245D-250D-20 (S)NEW DIMENSIONS
MONOCRYSTALLINE MODULES
WHY LDK SOLAR MODULES
DIMENSIONS PERFORMANCE AT LOW IRRADIANCE
• Industry leading module power output warranty• International quality, safety and performance certifications• Modules manufactured at ISO 9001 certified factories• High-reliability with guaranteed 0/+5W peak power classification• Module performance reinsurance policy (Munich RE)
WARRANTIES• 5 years for product defects in materials & workmanship• 12 years for 90% of warranted minimum power• 25 years for 80% of warranted minimum power
CERTIFICATES• IEC: IEC 61215, IEC 61730 (1&2), conformity to CE• UL1703 2002/03/15 Ed:3 Rev: 2004/06/30• ULC/ORD-C1703-01 second edition 2001/01/01• UL and Canadian standard for safety flat-plate
• ISO9001:2008 Quality Management System• CEC Listed: modules are elegible for California rebates• PV Cycle: voluntary module take back and recycling program
www.ldksolar.com module.sales@ldksolar.com
LIGHT OUR FUTURE
The typical relative change in module efficiency at an irradiance of 200W/m² in relation to 1000W/m²(both at 25°C and AM 1.5 spectrum) is less than 6%
1.05
2)
1
0.95
0.9
0.85
0.8200 300 400 500 600 700 800 900 1000
IV CURVE AT DIFFERENT IRRADIANCE LEVELS
0
1
2
4
3
6
5
0 5 10 15 20 25 30 35 40 45 50Voltage / V
Cur
rent
/ A
Rel
ativ
e Ef
ficie
ncy
1000W/m²
800W/m²
600W/m²
400W/m²
200W/m²
Above graphics according to LDK-220D-20(s)
4-10×10Drainage holes
4 places
8-8x3Drainage holes
8 places
Junction box
8-14x9Mounting slots
8 places
2-Ø4Ground holes
2 places
40
1000
976938
1630
1300
800
50
5030
3016
541
5
1630
976
Tolerance of length and width dimensions is ± 2 mm
160P-165P-170P-175P-180P-185P-190P-195P-200P-24 (S)NEW DIMENSIONS
POLYCRYSTALLINE MODULES
WHY LDK SOLAR MODULES
TYPENominal Output (Pmax) [W] Voltage at Pmax (Vmp) [V]Current at Pmax (Imp) [A]Open Circuit Voltage (Voc) [V]Short Circuit Current (Isc)The power tolerance is +/- 3% referred to the Nominal OutputMaximum System VoltageCell EfficiencyModule Efficiency
ELECTRIC CHARACTERISTICS (STC*)
STC* (Standard Test Conditions): Irradiance 1000W/m2, Module Temperature 25°C, Air Mass 1.5
IEC: 1000V / UL: 600 V
TYPENominal Output (Pmax) Voltage at Pmax (Vmp) Current at Pmax (Imp)Open Circuit Voltage (Voc)Short Circuit Current (Isc)
ELECTRICAL PERFORMANCE AT NOCT
NOCT: Irradiance 800 W/m2, Module Temperature 45± 2°C, Air Mass 1.5
DIMENSIONS PERFORMANCE AT LOW IRRADIANCE
• Industry leading module power output warranty• International quality, safety and performance certifications• Modules manufactured at ISO 9001 certified factories• High-reliability with guaranteed 0/+5W peak power classification
WARRANTIES• 5 years for product defects in materials & workmanship• 12 years for 90% of warranted minimum power• 25 years for 80% of warranted minimum power
CERTIFICATES• IEC: IEC 61215, IEC 61730 (1&2), conformity to CE• UL1703 2002/03/15 Ed:3 Rev: 2004/06/30• ULC/ORD-C1703-01 second edition 2001/01/01• UL and Canadian standard for safety flat-plate
• ISO9001:2008 Quality Management System• CEC Listed: modules are elegible for California rebates• PV Cycle: voluntary module take back and recycling program
TYPENOCT** Temperature Coefficient of PmaxTemperature Coefficient of VocTemperature Coefficient of IscMaximum Series Fuse RatingOperating TemperatureStorage Temperature
TEMPERATURE CHARACTERISTICS
NOCT**: Nominal Operation Cell Temperature Sun 800 W/m2; Air 20°C; wind speed 1m/s
45±2°C-0.47% / °C-0.34% / °C0.06% / °C
10 A-40 to +85°C-40 to +60°C
LDK-P-24 Series (s)
TYPEPacking ConfigurationQuantity/PalletLoading Capacity
PACKING CONFIGURATION
25 pcs./box 50 pcs./pallet
700 pcs. / 40 ft (H)
LDK-P-24 Series (s)
TYPESolar CellsFront CoverBack CoverEncapsulantFrameDiodesJunction BoxConnectorCablesDimensionWeightMax. Load
MECHANICAL CHARACTERISTICS
72 (6x12) polycrystalline silicon solar cells 125 x 125 mm3.2 mm thick, Tempered glass / AR coating glass
TPT (Tedlar-PET-Tedlar) / BBFEVA (Ethylene vinyl acetate)
Anodized aluminium alloy, double wall6 Bypass diodes serviceable
IP65 ratedMC4 or compatible connector
Lenght: 950 mm / Section: 4.0 mm2
1580 x 808 x 40 mm / 62.4 x 31.8 x 1.6 inches (new dimensions)15.6 kg / 34.4 lbs
Wind Load: 2400Pa / Snow Load: 5400 Pa
LDK-P-24 Series (s)
LDK Solar reserves the right to make specifications changes without any prior notice. This data sheet complies with the EN 50380 requirement. January 2011/V1/ ©LDK Solar Limited. All rights reserved. E.&O.E.
www.ldksolar.com module.sales@ldksolar.com
LIGHT OUR FUTURE
40808
1580
4-10×10Drainage holes
4 places8-8x3
Drainage holes8 places
Junction box
8-14x9Mounting slots
8 places
2-Ø4Ground holes
2 places The typical relative change in module efficiency at an irradiance of 200W/m² in relation to 1000W/m²(both at 25°C and AM 1.5 spectrum) is less than 6%
1.05
2)
1
0.95
0.9
0.85
0.8200 300 400 500 600 700 800 900 1000
IV CURVE AT DIFFERENT IRRADIANCE LEVELS
0
1
2
3
4
5
6
0 5 10 15 20 25 30 35 40 45 50Voltage / V
Cur
rent
/ A
Rel
ativ
e Ef
ficie
ncy
1000W/m²
800W/m²
600W/m²
400W/m²
200W/m²
Above graphics according to LDK-175P-24(s)
16035.14.6043.24.95
14.6612.53
160P-24(s)
11631.73.6639.84.01
16535.44.6843.65.04
15.1212.92
165P-24(s)
12032.33.7140.14.08
17035.94.7644.05.13
15.5813.32
170P-24(s)
12332.63.7740.54.15
17536.14.8744.35.21
16.0413.71
175P-24(s)
12733.13.8340.84.22
18036.44.9644.65.28
16.4914.10
180P-24(s)
13033.63.8741.14.27
18536.85.0244.95.51
16.9514.49
185P-24(s)
13433.63.9941.34.46
19037.25.1
45.15.6
17.4114.88
190P-24(s)
13834.14.0541.54.53
19537.55.2
45.35.69
17.8715.27
195P-24(s)
14134.64.1041.74.6
20037.85.3
45.55.78
18.3315.67
200P-24(s)
160P-24(s) 165P-24(s) 170P-24(s) 175P-24(s) 180P-24(s) 185P-24(s) 190P-24(s) 195P-24(s) 200P-24(s)
14535
4.1641.94.67
950
808770
1580
1300
800
50503030140
390
Tolerance of length and width dimensions is ± 2 mm
160P-165P-170P-175P-180P-185P-190P-195P-200P-24 (S)NEW DIMENSIONS
POLYCRYSTALLINE MODULES
WHY LDK SOLAR MODULES
TYPENominal Output (Pmax) [W] Voltage at Pmax (Vmp) [V]Current at Pmax (Imp) [A]Open Circuit Voltage (Voc) [V]Short Circuit Current (Isc)The power tolerance is +/- 3% referred to the Nominal OutputMaximum System VoltageCell EfficiencyModule Efficiency
ELECTRIC CHARACTERISTICS (STC*)
STC* (Standard Test Conditions): Irradiance 1000W/m2, Module Temperature 25°C, Air Mass 1.5
IEC: 1000V / UL: 600 V
TYPENominal Output (Pmax) Voltage at Pmax (Vmp) Current at Pmax (Imp)Open Circuit Voltage (Voc)Short Circuit Current (Isc)
ELECTRICAL PERFORMANCE AT NOCT
NOCT: Irradiance 800 W/m2, Module Temperature 45± 2°C, Air Mass 1.5
DIMENSIONS PERFORMANCE AT LOW IRRADIANCE
• Industry leading module power output warranty• International quality, safety and performance certifications• Modules manufactured at ISO 9001 certified factories• High-reliability with guaranteed 0/+5W peak power classification
WARRANTIES• 5 years for product defects in materials & workmanship• 12 years for 90% of warranted minimum power• 25 years for 80% of warranted minimum power
CERTIFICATES• IEC: IEC 61215, IEC 61730 (1&2), conformity to CE• UL1703 2002/03/15 Ed:3 Rev: 2004/06/30• ULC/ORD-C1703-01 second edition 2001/01/01• UL and Canadian standard for safety flat-plate
• ISO9001:2008 Quality Management System• CEC Listed: modules are elegible for California rebates• PV Cycle: voluntary module take back and recycling program
TYPENOCT** Temperature Coefficient of PmaxTemperature Coefficient of VocTemperature Coefficient of IscMaximum Series Fuse RatingOperating TemperatureStorage Temperature
TEMPERATURE CHARACTERISTICS
NOCT**: Nominal Operation Cell Temperature Sun 800 W/m2; Air 20°C; wind speed 1m/s
45±2°C-0.47% / °C-0.34% / °C0.06% / °C
10 A-40 to +85°C-40 to +60°C
LDK-P-24 Series (s)
TYPEPacking ConfigurationQuantity/PalletLoading Capacity
PACKING CONFIGURATION
25 pcs./box 50 pcs./pallet
700 pcs. / 40 ft (H)
LDK-P-24 Series (s)
TYPESolar CellsFront CoverBack CoverEncapsulantFrameDiodesJunction BoxConnectorCablesDimensionWeightMax. Load
MECHANICAL CHARACTERISTICS
72 (6x12) polycrystalline silicon solar cells 125 x 125 mm3.2 mm thick, Tempered glass / AR coating glass
TPT (Tedlar-PET-Tedlar) / BBFEVA (Ethylene vinyl acetate)
Anodized aluminium alloy, double wall6 Bypass diodes serviceable
IP65 ratedMC4 or compatible connector
Lenght: 950 mm / Section: 4.0 mm2
1580 x 808 x 40 mm / 62.4 x 31.8 x 1.6 inches (new dimensions)15.6 kg / 34.4 lbs
Wind Load: 2400Pa / Snow Load: 5400 Pa
LDK-P-24 Series (s)
LDK Solar reserves the right to make specifications changes without any prior notice. This data sheet complies with the EN 50380 requirement. January 2011/V1/ ©LDK Solar Limited. All rights reserved. E.&O.E.
www.ldksolar.com module.sales@ldksolar.com
LIGHT OUR FUTURE
40808
1580
4-10×10Drainage holes
4 places8-8x3
Drainage holes8 places
Junction box
8-14x9Mounting slots
8 places
2-Ø4Ground holes
2 places The typical relative change in module efficiency at an irradiance of 200W/m² in relation to 1000W/m²(both at 25°C and AM 1.5 spectrum) is less than 6%
1.05
2)
1
0.95
0.9
0.85
0.8200 300 400 500 600 700 800 900 1000
IV CURVE AT DIFFERENT IRRADIANCE LEVELS
0
1
2
3
4
5
6
0 5 10 15 20 25 30 35 40 45 50Voltage / V
Cur
rent
/ A
Rel
ativ
e Ef
ficie
ncy
1000W/m²
800W/m²
600W/m²
400W/m²
200W/m²
Above graphics according to LDK-175P-24(s)
16035.14.6043.24.95
14.6612.53
160P-24(s)
11631.73.6639.84.01
16535.44.6843.65.04
15.1212.92
165P-24(s)
12032.33.7140.14.08
17035.94.7644.05.13
15.5813.32
170P-24(s)
12332.63.7740.54.15
17536.14.8744.35.21
16.0413.71
175P-24(s)
12733.13.8340.84.22
18036.44.9644.65.28
16.4914.10
180P-24(s)
13033.63.8741.14.27
18536.85.0244.95.51
16.9514.49
185P-24(s)
13433.63.9941.34.46
19037.25.1
45.15.6
17.4114.88
190P-24(s)
13834.14.0541.54.53
19537.55.2
45.35.69
17.8715.27
195P-24(s)
14134.64.1041.74.6
20037.85.345.55.78
18.3315.67
200P-24(s)
160P-24(s) 165P-24(s) 170P-24(s) 175P-24(s) 180P-24(s) 185P-24(s) 190P-24(s) 195P-24(s) 200P-24(s)
14535
4.1641.94.67
950
808770
1580
1300
800
50503030140
390
Tolerance of length and width dimensions is ± 2 mm
TYPEtNominal Output (Pmax) [W] Voltage at Pmax (Vmp) [V]Current at Pmax (Imp) [A]Open Circuit Voltage (Voc) [V]Short Circuit Current (Isc)The power tolerance is +/- 3% referred to the Nominal OutputMaximum System VoltageCell EfficiencyModule Efficiency
ELECTRIC CHARACTERISTICS (STC*)
STC* (Standard Test Conditions): Irradiance 1000W/m2, Module Temperature 25°C, Air Mass 1.5
IEC: 1000V / UL: 600 V
TYPENominal Output (Pmax) Voltage at Pmax (Vmp) Current at Pmax (Imp)Open Circuit Voltage (Voc)Short Circuit Current (Isc)
ELECTRICAL PERFORMANCE AT NOCT
NOCT: Irradiance 800 W/m2, Module Temperature 45± 2°C, Air Mass 1.5
TYPENOCT** Temperature Coefficient of PmaxTemperature Coefficient of VocTemperature Coefficient of IscMaximum Series Fuse RatingOperating TemperatureStorage Temperature
TEMPERATURE CHARACTERISTICS
NOCT**: Nominal Operation Cell Temperature Sun 800 W/m2; Air 20°C; wind speed 1m/s
45±2°C-0.47 % / °C-0.34 % / °C0.06 % / °C
12 A-40 to +85°C-40 to +60°C
LDK-P-20 Series (s)
TYPEPacking ConfigurationQuantity/PalletLoading Capacity
PACKING CONFIGURATION
25 pcs./box 50 pcs./pallet
700 pcs. / 40 ft (H)
LDK-P-20 Series (s)
TYPESolar CellsFront CoverBack CoverEncapsulantFrameDiodesJunction BoxConnectorCablesDimensionWeightMax. Load
MECHANICAL CHARACTERISTICS
60 (6x10) polycrystalline silicon solar cells 156 x 156 mm3.2 mm thick, Tempered glass / AR coating glass
TPT (Tedlar-PET-Tedlar) / BBFEVA (Ethylene vinyl acetate)
Anodized aluminium alloy, double wall6 Bypass diodes serviceable
IP65 ratedMC4 or compatible connector
Lenght: 1000 mm / Section: 4.0 mm2
1630 x 976 x 40 mm / 64.2 x 38.4x 1.6 inches (new dimensions)20 kg / 44.1 lbs
Wind Load: 2400Pa / Snow Load: 5400 Pa
LDK-P-20 Series (s)
LDK Solar reserves the right to make specifications changes without any prior notice. This data sheet complies with the EN 50380 requirement. January 2011/V1/ ©LDK Solar Limited. All rights reserved. E.&O.E.
20029.66.7536.07.82
14.1212.57
200P-20(s)
14525.15.8033.16.33
20529.66.9336.07.82
14.4712.89
205P-20(s)
14925.75.8033.16.33
21029.77.0736.17.83
14.8313.20
210P-20(s)
15226.25.8133.26.34
21529.87.2336.37.98
15.1813.51
215P-20(s)
15626.35.9333.46.46
22029.87.4036.58.14
15.5313.83
220P-20(s)
15926.46.0433.66.59
22529.97.5336.78.24
15.8914.14
225P-20(s)
16326.76.1233.86.67
23029.97.6836.88.34
16.2414.46
230P-20(s)
16727.16.1933.96.75
23530.07.8436.88.35
16.5914.77
235P-20(s)
17027.46.2233.96.76
24030.07.9836.98.35
16.9415.09
240P-20(s)
17428.06.2334.06.76
24530.18.1437.28.48
17.2915.40
245P-20(s)
17828.16.3334.36.87
25030.28.2837.58.59
17.6415.71
250P-20(s)
200P-20(s) 205P-20(s) 210P-20(s) 215P-20(s) 220P-20(s) 225P-20(s) 230P-20(s) 235P-20(s) 240P-20(s) 245P-20(s) 250P-20(s)
18128.26.4234.56.95
200P-205P-210P-215P-220P-225P-230P-235P-240P-245P-250P-20 (S)NEW DIMENSIONS
POLYCRYSTALLINE MODULES
WHY LDK SOLAR MODULES
DIMENSIONS PERFORMANCE AT LOW IRRADIANCE
• Industry leading module power output warranty• International quality, safety and performance certifications• Modules manufactured at ISO 9001 certified factories• High-reliability with guaranteed 0/+5W peak power classification• Module performance reinsurance policy (Munich RE)
WARRANTIES• 5 years for product defects in materials & workmanship• 12 years for 90% of warranted minimum power• 25 years for 80% of warranted minimum power
CERTIFICATES• IEC: IEC 61215, IEC 61730 (1&2), conformity to CE• UL1703 2002/03/15 Ed:3 Rev: 2004/06/30• ULC/ORD-C1703-01 second edition 2001/01/01• UL and Canadian standard for safety flat-plate
• ISO9001:2008 Quality Management System• CEC Listed: modules are elegible for California rebates• PV Cycle: voluntary module take back and recycling program• MCS The Microgeneration Certification Scheme UK
www.ldksolar.com module.sales@ldksolar.com
LIGHT OUR FUTURE
4-10×10Drainage holes
4 places
8-8x3Drainage holes
8 places
8-14x9Mounting slots
8 places
2-Ø4Ground holes
2 places The typical relative change in module efficiency at an irradiance of 200W/m² in relation to 1000W/m²(both at 25°C and AM 1.5 spectrum) is less than 6%
1.05
2)
1
0.95
0.9
0.85
0.8200 300 400 500 600 700 800 900 1000
IV CURVE AT DIFFERENT IRRADIANCE LEVELS
Voltage / V
Cur
rent
/ A
Rel
ativ
e Ef
ficie
ncy
1000W/m²
800W/m²
600W/m²
400W/m²
200W/m²
Above graphics according to LDK-220P-20(s)
40
1000
976938
1630
1300
800
50
5030
30165
415
976
1630
Junction box
0 5 10 15 20 25 30 35 40 45 50
Tolerance of length and width dimensions is ± 2 mm
TYPEtNominal Output (Pmax) [W] Voltage at Pmax (Vmp) [V]Current at Pmax (Imp) [A]Open Circuit Voltage (Voc) [V]Short Circuit Current (Isc)The power tolerance is +/- 3% referred to the Nominal OutputMaximum System VoltageCell EfficiencyModule Efficiency
ELECTRIC CHARACTERISTICS (STC*)
STC* (Standard Test Conditions): Irradiance 1000W/m2, Module Temperature 25°C, Air Mass 1.5
IEC: 1000V / UL: 600 V
TYPENominal Output (Pmax) Voltage at Pmax (Vmp) Current at Pmax (Imp)Open Circuit Voltage (Voc)Short Circuit Current (Isc)
ELECTRICAL PERFORMANCE AT NOCT
NOCT: Irradiance 800 W/m2, Module Temperature 45± 2°C, Air Mass 1.5
TYPENOCT** Temperature Coefficient of PmaxTemperature Coefficient of VocTemperature Coefficient of IscMaximum Series Fuse RatingOperating TemperatureStorage Temperature
TEMPERATURE CHARACTERISTICS
NOCT**: Nominal Operation Cell Temperature Sun 800 W/m2; Air 20°C; wind speed 1m/s
45±2°C-0.47 % / °C-0.34 % / °C0.06 % / °C
12 A-40 to +85°C-40 to +60°C
LDK-P-20 Series (s)
TYPEPacking ConfigurationQuantity/PalletLoading Capacity
PACKING CONFIGURATION
25 pcs./box 50 pcs./pallet
700 pcs. / 40 ft (H)
LDK-P-20 Series (s)
TYPESolar CellsFront CoverBack CoverEncapsulantFrameDiodesJunction BoxConnectorCablesDimensionWeightMax. Load
MECHANICAL CHARACTERISTICS
60 (6x10) polycrystalline silicon solar cells 156 x 156 mm3.2 mm thick, Tempered glass / AR coating glass
TPT (Tedlar-PET-Tedlar) / BBFEVA (Ethylene vinyl acetate)
Anodized aluminium alloy, double wall6 Bypass diodes serviceable
IP65 ratedMC4 or compatible connector
Lenght: 1000 mm / Section: 4.0 mm2
1630 x 976 x 40 mm / 64.2 x 38.4x 1.6 inches (new dimensions)20 kg / 44.1 lbs
Wind Load: 2400Pa / Snow Load: 5400 Pa
LDK-P-20 Series (s)
LDK Solar reserves the right to make specifications changes without any prior notice. This data sheet complies with the EN 50380 requirement. January 2011/V1/ ©LDK Solar Limited. All rights reserved. E.&O.E.
20029.66.7536.07.82
14.1212.57
200P-20(s)
14525.15.8033.16.33
20529.66.9336.07.82
14.4712.89
205P-20(s)
14925.75.8033.16.33
21029.77.0736.17.83
14.8313.20
210P-20(s)
15226.25.8133.26.34
21529.87.2336.37.98
15.1813.51
215P-20(s)
15626.35.9333.46.46
22029.87.4036.58.14
15.5313.83
220P-20(s)
15926.46.0433.66.59
22529.97.5336.78.24
15.8914.14
225P-20(s)
16326.76.1233.86.67
23029.97.6836.88.34
16.2414.46
230P-20(s)
16727.16.1933.96.75
23530.07.8436.88.35
16.5914.77
235P-20(s)
17027.46.2233.96.76
24030.07.9836.98.35
16.9415.09
240P-20(s)
17428.06.2334.06.76
24530.18.1437.28.48
17.2915.40
245P-20(s)
17828.16.3334.36.87
25030.28.2837.58.59
17.6415.71
250P-20(s)
200P-20(s) 205P-20(s) 210P-20(s) 215P-20(s) 220P-20(s) 225P-20(s) 230P-20(s) 235P-20(s) 240P-20(s) 245P-20(s) 250P-20(s)
18128.26.4234.56.95
200P-205P-210P-215P-220P-225P-230P-235P-240P-245P-250P-20 (S)NEW DIMENSIONS
POLYCRYSTALLINE MODULES
WHY LDK SOLAR MODULES
DIMENSIONS PERFORMANCE AT LOW IRRADIANCE
• Industry leading module power output warranty• International quality, safety and performance certifications• Modules manufactured at ISO 9001 certified factories• High-reliability with guaranteed 0/+5W peak power classification• Module performance reinsurance policy (Munich RE)
WARRANTIES• 5 years for product defects in materials & workmanship• 12 years for 90% of warranted minimum power• 25 years for 80% of warranted minimum power
CERTIFICATES• IEC: IEC 61215, IEC 61730 (1&2), conformity to CE• UL1703 2002/03/15 Ed:3 Rev: 2004/06/30• ULC/ORD-C1703-01 second edition 2001/01/01• UL and Canadian standard for safety flat-plate
• ISO9001:2008 Quality Management System• CEC Listed: modules are elegible for California rebates• PV Cycle: voluntary module take back and recycling program• MCS The Microgeneration Certification Scheme UK
www.ldksolar.com module.sales@ldksolar.com
LIGHT OUR FUTURE
4-10×10Drainage holes
4 places
8-8x3Drainage holes
8 places
8-14x9Mounting slots
8 places
2-Ø4Ground holes
2 places The typical relative change in module efficiency at an irradiance of 200W/m² in relation to 1000W/m²(both at 25°C and AM 1.5 spectrum) is less than 6%
1.05
2)
1
0.95
0.9
0.85
0.8200 300 400 500 600 700 800 900 1000
IV CURVE AT DIFFERENT IRRADIANCE LEVELS
Voltage / V
Cur
rent
/ A
Rel
ativ
e Ef
ficie
ncy
1000W/m²
800W/m²
600W/m²
400W/m²
200W/m²
Above graphics according to LDK-220P-20(s)
40
1000
976938
1630
1300
800
50
5030
30165
415
976
1630
Junction box
0 5 10 15 20 25 30 35 40 45 50
Tolerance of length and width dimensions is ± 2 mm
TYPENominal Output (Pmax) [W] Voltage at Pmax (Vmp) [V]Current at Pmax (Imp) [A]Open Circuit Voltage (Voc) [V]Short Circuit Current (Isc)The power tolerance is +/- 3% referred to the Nominal OutputMaximum System VoltageCell EfficiencyModule Efficiency
ELECTRIC CHARACTERISTICS (STC*)
STC* (Standard Test Conditions): Irradiance 1000W/m2, Module Temperature 25°C, Air Mass 1.5
IEC: 1000V / UL: 600 V
TYPENominal Output (Pmax) Voltage at Pmax (Vmp) Current at Pmax (Imp)Open Circuit Voltage (Voc)Short Circuit Current (Isc)
ELECTRICAL PERFORMANCE AT NOCT
NOCT: Irradiance 800 W/m2, Module Temperature 45± 2°C, Air Mass 1.5
TYPENOCT** Temperature Coefficient of PmaxTemperature Coefficient of VocTemperature Coefficient of IscMaximum Series Fuse RatingOperating TemperatureStorage Temperature
TEMPERATURE CHARACTERISTICS
NOCT**: Nominal Operation Cell Temperature Sun 800 W/m2; Air 20°C; wind speed 1m/s
45±2°C-0.47 % / °C-0.34 % / °C0.06 % / °C
12 A-40 to +85°C-40 to +60°C
LDK-P-24 Series (s)
TYPEPacking ConfigurationQuantity/PalletLoading Capacity
PACKING CONFIGURATION
20 pcs./box 40 pcs./pallet
440 pcs. / 40 ft (H)
LDK-P-24 Series (s)
TYPESolar CellsFront CoverBack CoverEncapsulantFrameDiodesJunction BoxConnectorCablesDimensionWeightMax. Load
MECHANICAL CHARACTERISTICS
72 (6x12) polycrystalline silicon solar cells 156 x 156 mm4 mm thick, Tempered glass / AR coating glass
TPT (Tedlar-PET-Tedlar) / BBFEVA (Ethylene vinyl acetate)
Anodized aluminium alloy, double wall6 Bypass diodes serviceable
IP65 ratedMC4 or compatible connector
Lenght: 1200 mm / Section: 4.0 mm2
1946 x 976 x 50 mm / 77.0 x 38.4x 2.0 inches (new dimensions)27.3 kg / 67.2 lbs
Wind Load: 2400Pa / Snow Load: 5400 Pa
LDK-P-24 Series (s)
LDK Solar reserves the right to make specifications changes without any prior notice. This data sheet complies with the EN 50380 requirement. January 2011/V1/ ©LDK Solar Limited. All rights reserved. E.&O.E.
245P-24(s)
24035.86.7044.18.01
14.2712.64
240P-24(s)
17429.95.8240.66.48
24535.86.8544.18.02
14.5712.90
17830.35.8640.66.49
250P-24(s)
25035.96.9644.18.02
14.8613.16
18130.85.8940.66.49
255P-24(s)
25535.97.1144.180.4
15.1613.43
18531.05.9640.66.51
260P-24(s)
26036.07.2344.280.6
15.4613.69
18831.46.0140.76.53
265P-24(s)
26536.17.3544.28.14
15.7513.95
19231.66.0740.76.59
270P-24(s)
27036.27.4744.28.21
16.0514.22
19631.86.1540.76.65
275P-24(s)
27536.27.6044.38.28
16.3514.48
19932.16.2140.86.70
280P-24(s)
28036.37.7244.38.36
16.6614.74
20332.46.2740.86.77
285P-24(s)
28536.47.8344.48.44
16.9615.01
20732.86.3140.96.81
290P-24(s)
245P-24(s)240P-24(s) 250P-24(s) 255P-24(s) 260P-24(s) 265P-24(s) 270P-24(s) 275P-24(s) 280P-24(s) 285P-24(s) 290P-24(s)
29036.57.9544.48.52
17.2715.27
21033
6.3940.96.91
240P-245P-250P-260P-265P-270P-275P-280P-285P-290P-24 (S)NEW DIMENSIONS
POLYCRYSTALLINE MODULES
WHY LDK SOLAR MODULES
DIMENSIONS PERFORMANCE AT LOW IRRADIANCE
• Industry leading module power output warranty• International quality, safety and performance certifications• Modules manufactured at ISO 9001 certified factories• High-reliability with guaranteed 0/+5W peak power classification
WARRANTIES• 5 years for product defects in materials & workmanship• 12 years for 90% of warranted minimum power• 25 years for 80% of warranted minimum power
CERTIFICATES• IEC: IEC 61215, IEC 61730 (1&2), conformity to CE• UL1703 2002/03/15 Ed:3 Rev: 2004/06/30• ULC/ORD-C1703-01 second edition 2001/01/01• UL and Canadian standard for safety flat-plate
• ISO9001:2008 Quality Management System• CEC Listed: modules are elegible for California rebates• PV Cycle: voluntary module take back and recycling program
www.ldksolar.com module.sales@ldksolar.com
LIGHT OUR FUTURE
4-10×10Drainage holes
4 places8-8x3
Drainage holes8 places
8-14x9Mounting slots
8 places
2-Ø4Ground holes
2 placesThe typical relative change in module efficiency at an irradiance of 200W/m² in relation to 1000W/m²(both at 25°C and AM 1.5 spectrum) is less than 6%
1.05
2)
1
0.95
0.9
0.85
0.8200 300 400 500 600 700 800 900 1000
IV CURVE AT DIFFERENT IRRADIANCE LEVELS
0
1
2
3
4
5
6
0 5 10 15 20 25 30 35 40 45 50Voltage / V
Cur
rent
/ A
Rel
ativ
e Ef
ficie
ncy
1000W/m²
800W/m²
600W/m²
400W/m²
200W/m²
Above graphics according to LDK-260P-24(s)
1200
976924
1946
1300
800
Tolerance of length and width dimensions is ± 2 mm
5252
50
40
40
32357
3
976
1946
Junction box
TYPENominal Output (Pmax) [W] Voltage at Pmax (Vmp) [V]Current at Pmax (Imp) [A]Open Circuit Voltage (Voc) [V]Short Circuit Current (Isc)The power tolerance is +/- 3% referred to the Nominal OutputMaximum System VoltageCell EfficiencyModule Efficiency
ELECTRIC CHARACTERISTICS (STC*)
STC* (Standard Test Conditions): Irradiance 1000W/m2, Module Temperature 25°C, Air Mass 1.5
IEC: 1000V / UL: 600 V
TYPENominal Output (Pmax) Voltage at Pmax (Vmp) Current at Pmax (Imp)Open Circuit Voltage (Voc)Short Circuit Current (Isc)
ELECTRICAL PERFORMANCE AT NOCT
NOCT: Irradiance 800 W/m2, Module Temperature 45± 2°C, Air Mass 1.5
TYPENOCT** Temperature Coefficient of PmaxTemperature Coefficient of VocTemperature Coefficient of IscMaximum Series Fuse RatingOperating TemperatureStorage Temperature
TEMPERATURE CHARACTERISTICS
NOCT**: Nominal Operation Cell Temperature Sun 800 W/m2; Air 20°C; wind speed 1m/s
45±2°C-0.47 % / °C-0.34 % / °C0.06 % / °C
12 A-40 to +85°C-40 to +60°C
LDK-P-24 Series (s)
TYPEPacking ConfigurationQuantity/PalletLoading Capacity
PACKING CONFIGURATION
20 pcs./box 40 pcs./pallet
440 pcs. / 40 ft (H)
LDK-P-24 Series (s)
TYPESolar CellsFront CoverBack CoverEncapsulantFrameDiodesJunction BoxConnectorCablesDimensionWeightMax. Load
MECHANICAL CHARACTERISTICS
72 (6x12) polycrystalline silicon solar cells 156 x 156 mm4 mm thick, Tempered glass / AR coating glass
TPT (Tedlar-PET-Tedlar) / BBFEVA (Ethylene vinyl acetate)
Anodized aluminium alloy, double wall6 Bypass diodes serviceable
IP65 ratedMC4 or compatible connector
Lenght: 1200 mm / Section: 4.0 mm2
1946 x 976 x 50 mm / 77.0 x 38.4x 2.0 inches (new dimensions)27.3 kg / 67.2 lbs
Wind Load: 2400Pa / Snow Load: 5400 Pa
LDK-P-24 Series (s)
LDK Solar reserves the right to make specifications changes without any prior notice. This data sheet complies with the EN 50380 requirement. January 2011/V1/ ©LDK Solar Limited. All rights reserved. E.&O.E.
245P-24(s)
24035.86.7044.18.01
14.2712.64
240P-24(s)
17429.95.8240.66.48
24535.86.8544.18.02
14.5712.90
17830.35.8640.66.49
250P-24(s)
25035.96.9644.18.02
14.8613.16
18130.85.8940.66.49
255P-24(s)
25535.97.1144.180.4
15.1613.43
18531.05.9640.66.51
260P-24(s)
26036.07.2344.280.6
15.4613.69
18831.46.0140.76.53
265P-24(s)
26536.17.3544.28.14
15.7513.95
19231.66.0740.76.59
270P-24(s)
27036.27.4744.28.21
16.0514.22
19631.86.1540.76.65
275P-24(s)
27536.27.6044.38.28
16.3514.48
19932.16.2140.86.70
280P-24(s)
28036.37.7244.38.36
16.6614.74
20332.46.2740.86.77
285P-24(s)
28536.47.8344.48.44
16.9615.01
20732.86.3140.96.81
290P-24(s)
245P-24(s)240P-24(s) 250P-24(s) 255P-24(s) 260P-24(s) 265P-24(s) 270P-24(s) 275P-24(s) 280P-24(s) 285P-24(s) 290P-24(s)
29036.57.9544.48.52
17.2715.27
21033
6.3940.96.91
240P-245P-250P-260P-265P-270P-275P-280P-285P-290P-24 (S)NEW DIMENSIONS
POLYCRYSTALLINE MODULES
WHY LDK SOLAR MODULES
DIMENSIONS PERFORMANCE AT LOW IRRADIANCE
• Industry leading module power output warranty• International quality, safety and performance certifications• Modules manufactured at ISO 9001 certified factories• High-reliability with guaranteed 0/+5W peak power classification
WARRANTIES• 5 years for product defects in materials & workmanship• 12 years for 90% of warranted minimum power• 25 years for 80% of warranted minimum power
CERTIFICATES• IEC: IEC 61215, IEC 61730 (1&2), conformity to CE• UL1703 2002/03/15 Ed:3 Rev: 2004/06/30• ULC/ORD-C1703-01 second edition 2001/01/01• UL and Canadian standard for safety flat-plate
• ISO9001:2008 Quality Management System• CEC Listed: modules are elegible for California rebates• PV Cycle: voluntary module take back and recycling program
www.ldksolar.com module.sales@ldksolar.com
LIGHT OUR FUTURE
4-10×10Drainage holes
4 places8-8x3
Drainage holes8 places
8-14x9Mounting slots
8 places
2-Ø4Ground holes
2 placesThe typical relative change in module efficiency at an irradiance of 200W/m² in relation to 1000W/m²(both at 25°C and AM 1.5 spectrum) is less than 6%
1.05
2)
1
0.95
0.9
0.85
0.8200 300 400 500 600 700 800 900 1000
IV CURVE AT DIFFERENT IRRADIANCE LEVELS
0
1
2
3
4
5
6
0 5 10 15 20 25 30 35 40 45 50Voltage / V
Cur
rent
/ A
Rel
ativ
e Ef
ficie
ncy
1000W/m²
800W/m²
600W/m²
400W/m²
200W/m²
Above graphics according to LDK-260P-24(s)
1200
976924
1946
1300
800
Tolerance of length and width dimensions is ± 2 mm
5252
50
40
40
32357
3
976
1946
Junction box
PV MODULES
LDK SOLAR ENERGYSYSTEMS MODULES
www.ldksolar.com
LIGHT OUR FUTURELIGHT OUR FUTURE
3.0 GWWAFER PRODUCTION
CAPACITY
JIANGXI LDK SOLAR, LTDLDK Avenue, Economic Development Zone, Xinyu, Jiangxi, 338032 P.R. - China
LDK SOLAR HI-TECH (SUZHOU) CO., LTD 6th Floor 1368 Wuzhong Avenue, Wuzhong District, Suzhou City, P.R.China
Tel. +0086.512.82250137 - Fax +0086.512.82250101LDK SOLAR HI-TECH (NANCHANG) SO., LTD.
No.998 TorchS Street, Nanchang City, Jiangxi Province, P.R.China - Tel. 086.791.810 5065 - Fax 0086.791.810 8260LDK SOLAR EUROPE HOLDING S.A
412F Route d'Esch L-2086 - Luxembourg LDK SOLAR USA, INC.
1290 Oakmead Parkway, Suite 306, Sunnyvale, CA 94085 - USA - info.usa@ldksolar.com - Ph. 001.408.2450858 LDK SOLAR GERMANY
Landsberger Strasse 302 80687 Munich - Germany - Ph. +49 (89).90405.276 - info.de@ldksolar.com LDK SOLAR ITALY
Via S. Martino, 25 31020 San Zenone degli Ezzelini, Treviso - Italy - Tel. +39.0423.948833 - info.it@ldksolar.comVia Giulio Cesare Procaccini, 48 20154 Milano - Italy - Tel. +39.02.87242050
LDK SOLAR FRANCEhugh.harris@ldksolar.com - Ph. +33.619.606288
LDK SOLAR SPAINoscar.artal@ldksolar.com - Ph. +34.672.074200
Recommended