View
221
Download
0
Category
Preview:
Citation preview
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 1/34
Ministry of Education and Culture
Republic Institute for Protection of
Historical and Natural Heritage of
the Republic of Srpska
Memorial Area
Donja Gradina – Kozarska Dubica
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 2/34
2
Poplar Tree of Horror
PROJECT FOR
CONSERVATION AND RESTORATION WORKS
TABLE OF CONTENTS
1. BACKGROUND INFORMATION ABOUT THE MEMORIAL
AREA
2. BACKGROUND INFORMATION ABOUT THE PROJECT
3. INTRODUCTION
3.1 Project Task
3.2. Project Design Guidelines
STAGE А
4. CONSERVATION AND RESTORATION WORKS ON
POPLAR OF HORROR
4.1. Historical background
4.2 . Photo-documentation
5. REPORT ON RESULTS
5.1. Information-documentation basis
5.2. Previous research and conservation and restoration works
5.3. Photographs of units and details
6. CONSERVATORY METHODOLOGY
6.1. Defining the condition and cause of damage
6.2. Conservation and restoration works with methodology
6.3. Technical documentation
7. PRICED BILL OF QUANTITIES FOR STAGE A
STAGE B
8. EXPERT OPINION ON THE STABILITY OF STEEL
BEARERS OF POPLAR OF HORROR
8.1. Priced bill of quantities
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 3/34
3
9. MONETARY RESOURCES FOR PERFORMING WORKS
IN STAGES A AND B
10. TIME SCHEDULE FOR PERFORMING WORKS
1. BACKGROUND INFORMATION ABOUT THE MEMORIAL
AREA
1.1. Name of Memorial Area the part of which is the location
Public Institution Memorial Area Donja Gradina
1.2. Name of the location
Poplar Tree of Horror
1.3. Memorial Area
Memorial Area Jasenovac was formed in 1968, and Donja Gradina is its part.
After the break-up of SFRY, Donja Gradina and the localities on the right-hand bank
of the Una and Sava rivers remained in the Republic of Srpska / Bosnia and Herzegovina.
In November 1996 the National Assembly of the Republic of Srpska passed the Law
on Donja Gradina Memorial Area which governed the status of this Memorial Area.
1.4. Number and date of the decision of the National Assembly on determining
the status
The Law on Donja Gradina Memorial Area, which governs its status, was passed by virtue of
the Decision of the Republic of Srpska National Assembly, no. 02-871/96 dated 09 July 1996.
According to the decision of the Republic of Srpska National Assembly of 15 December 2008, Law on Amendments to the Law on Donja Gradina Memorial Area was passed.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 4/34
4
1.5. Number of “ RS Official Gazette “ in which the decision was published.
The Law on Donja Gradina Memorial Area was published in the Republic of Srpska Official
Gazette, no. 16/96;
The Law on Amendments to the Law on Donja Gradina Memorial Area was published in the
Republic of Srpska Official Gazette, no. 1/09.
1.6. Place, Municipality (street and address)
Donja Gradina, 79290 Kozarska Dubica,
1.7. Name (Company name) of the owner, i.e. user and address
Public Institution Memorial Area Donja Gradina
2. GENERAL INFORMATION ABOUT THE PROJECT
2.1. Name of the project
Project of conservation and restoration works on Poplar Tree of Horror in Donja
Gradina Memorial Area
2.2. Type of project
Conservation – restoration works on Poplar Tree of Horror
2.3. Party commissioning the project
Ministry of Education and Culture of the Republic of Srpska and Public Institution
Donja Gradina Memorial Area
2.4. Project implementer
Republic’s Institute for the Protection of Cultural and Historical Heritage of the
Republic of Srpska, Banja Luka
2.5. Responsible person
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 5/34
5
director Goran Milojevic, B.Sc. Arch.
2.6. Project design manager
Milica Kotur, MA, BSc. conservation-restoration
Introduction and Stage A
2.7. Making of Stage B
Radovan Belesin, B.Sc. Construction Eng.
2.8. Collaborators on the project
Vanja Dursun Sotra, MA
Nebojsa Milicevic, B.A. Communicology
3. INTRODUCTION
3.1 Project task
The current condition of Donja Gradina Memorial Area is quite bad and requires
taking of urgent measures on conservation and restoration. This is especially evident in
Poplar Tree of Horror, one of the most horrendous witnesses of crimes committed by the
Ustashe during World War II.
Thousands of innocent people were tortured in a most horrifying way and then hanged
on the Poplar Tree of Horror.
In 1978 the Poplar Tree was destroyed in a storm, as its interior was rotten in the
lower part.
At that time the tree and the metal wedge that had been preserved were protected andconserved and the poplar tree was placed horizontally on metal bearers.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 6/34
6
In September 1995, during the war, the Poplar tree was hit by an inflammable
projectile. Its lower part caught fire and the tree was dislocated from its position on the
bearers by about fifty centimeters in the direction North-South. The flame additionally
devastated the damaged structure of the tree.
The poplar is situated on a small plateau in the proximity of the mouth of the Una into
the Sava, where the concentration of moist is high.
All this significantly contributed to its current bad condition, and has led to the
necessity of taking protection measures as soon as possible.
Due to the great importance that it has, both from historical and memorial point of
view, and the complexity of the issue in the conservation sense, the Poplar Tree of Horror
requires carrying out of a comprehensive analysis.
The project task of conservation and restoration works on Poplar Tree of Horror is
related to defining the cause of damage, defining the condition as it was found, as well as the
protection measures in order to make the best possible project documentation and create the
most adequate methodological and technological procedures during conservation and
restoration works.
3.2. Project design guidelines
Guidelines for making the Project of Conservation and Restoration of Poplar Tree
of Horror in Donja Gradina Memorial Area, relate to stages A and B of the project.
Stage A implies dealing with the historical problematic in the introduction, as well as
defining of the following:
• previously applied conservatory procedures,
• cause of damage,
• current condition and
• methodology of conservation and restoration works on repair of Poplar Tree of
Horror with the
• envisioned degree of presentation.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 7/34
7
Stage B implies static approach in defining the condition of bearers of the poplar tree,
as well as guidelines for making the roof structure above the Poplar Tree of Horror that will
directly protect it from exposure to weather impacts and provide it with appropriate
conditions.
STAGE A
4.0. CONSERVATION-RESTORATION WORKS ON POPLAR
TREE OF HORROR
4.1. Historical background
Donja Gradina Memorial Area is located in a village that has the same name, in the
municipality Kozarska Dubica.
About 700.000 men, women and children were killed in the most horrendous way in
the Ustashe concentration camp Jasenovac from August 1941 to April 1945. Of this number,
about 360.000 innocent victims were killed in the area of Donja Gradina, which is the biggest
and direst Nazi execution place in former Yugoslavia and a third one by its size and atrocities
committed in it in the occupied Europe.
The biggest place of execution of the concentration camp Jasenovac was in the area
covered by Donja Gradina Memorial Area. The history of Donja Gradina is inseparable from
the history of Jasenovac, the Ustashe death camp.
According to research carried out so far, the Ustashe killed more than 365.000
innocent men, women and children. Most inmates in the concentration camp Jasenovac,
which was situated on the left bank of the Sava river, were transported on a ferry across the
river to Donja Gradina, killed and buried in mass graves. This Ustashe death factory wasactive from fall 1941 to April 1945. 105 mass graves were discovered in the area of Donja
Gradina, divided in 9 grave fields.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 8/34
8
In this Memorial Area, in the place where the Una flows into the Sava, “Poplar Tree
of Horror” or “Fr Satan’s Poplar Tree”, as it was called by the inmates, is located,
representing a natural monument, which testifies of most horrifying crimes committed by the
Ustashe.
Under the poplar tree and on it, thousands of men, women and children were hanged,
who were most horrendously tortured before hanging. In tortures before the hanging, the
cruelest person was the Ustashe major Miroslav Filipovic Majstorovic, called “Fr Satan” by
the camp inmates.
After World War II, Poplar was one of the most important symbols of Donja Gradina
execution place.
In 1978 Poplar was knocked down in a storm.
Then the tree as well as the metal wedges that were preserved on it, was protected and
conserved, and the poplar was placed horizontally within the metal bearers.
In Donja Gradina one can find the remains of the Ustashe “Soap factory”, in which
the Ustashe made soap of fat parts of inmates’ bodies. The remains of this factory include
three cauldrons, three lids, a depositor, a high-pressure receptacle with a lid and a separator.
These are silent witnesses of dreadful crimes committed in the Ustashe camp
Jasenovac.
Under the Law on Construction and Financing Donja Gradina Memorial Area (SR
BiH Official Gazette, no. 13/75), Donja Gradina was proclaimed a memorial area after which
works were pursued on its development.
Until the last war, from 1991 to 1995, Donja Gradina Memorial Area was part of the
memorial complex Jasenovac forming a “Memorial Area Jasenovac-Gradina”, the aim of
which, as an institution, was research, presentation and maintenance of the complex
Jasenovac-Gradina.
After the break-up of former Yugoslavia, the Memorial Area disintegrated too. Part of
the complex that was situated on the left bank of the Sava was assigned to the Republic of
Croatia and the part that was located on the right bank, i.e. Donja Gradina, to the Republic of
Srpska, BiH.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 9/34
9
By virtue of the decision of the Republic of Srpska National Assembly, no. 02-871/96
dated 09 July 1996, a law was passed on Donja Gradina Memorial Area that regulated the
status of this memorial complex.
Donja Gradina Memorial Area is a historical area, which, with its many mass graves,
represents a most poignant testimony of unprecedented suffering and tragedy of innocent
victims in World War II. As such, Donja Gradina is one of the biggest memorial areas in our
history calling for both present and future generations to bow before the suffering of the
victims perished there.
4.2 .Photo-documentation
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 10/34
10
Satellite image and the position of Poplar Tree of Horror (in red circle)
5. REPORT ON THE RESULTS
5.1. Information-documentation basis
- Program of Development of Donja Gradina Memorial Area, Urban planning
Institute BiH, Sarajevo 1977
- Space plan of Donja Gradina Memorial Area – pre-draft, Urban planning Institute
BiH, Sarajevo 1992
- Regulation plan of part of the immediate area of Donja Gradina Memorial Area
„Donja Gradina Village“, Urban planning Institute BiH, Sarajevo 1981.
- Horticultural Development of Donja Gradina Memorial Area, main design,
Sarajevo, Sept. 1981.
- Information Center of Donja Gradina Memorial Area – main design, Sarajevo,
Jan. 1981
- Expert opinion on restoration of “Soap Factory” and “Poplar Tree of Horror” in
Donja Gradina Memorial Area, 2003. Republic’s Institute for Protection of Cultural
and Historical Heritage of Republic of Srpska, Banja Luka
- Law on Donja Gradina Memorial Area 1975.
- Law on Donja Gradina Memorial Area 1996, published in Republic of Srpska Official
Gazette, no. 16/96;
- Law on Amendments to the Law on Donja Gradina Memorial Area published in the
Republic of Srpska Official Gazette, no. 1/09
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 11/34
11
Program of Development of Donja Gradina Memorial Area, Urban Planning Institute BiH,
Sarajevo 1977
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 12/34
12
Space Plan of Donja Gradina Memorial Area – pre-draft , Urban planning Institute BiH,
Sarajevo 1992
5.2. Research and conservation works carried out so far
Poplar tree was knocked down in 1978 in a storm.
The tree rotted in the lower part due to age and high concentration of moist. In the
very vicinity the Una river flows into the Sava. During the storm under a blow of wind, thetree fell down on the ground, and most of its branches were destroyed.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 13/34
13
At that time protection and conservation of the tree was done with metal wedges, and
the poplar was placed horizontally on three metal bearers.
Conservation and restoration works on Poplar Tree of Horror were carried out by the
Laboratory for Wood Protection R.O. Sipad-IRC OOUR “Sumarpojekt” from Sarajevo, with
participation of R.O. “Vranica” – Sarajevo, OOUR “Bobovac” – Vares. The works werecarried out in 1979.
5.3. Photograph of the whole tree and the details
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 14/34
14
Poplar Tree of Horror - as it looked before
Poplar Tree of Horror – as it looks today
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 15/34
15
6. CONSERVATION TECHNOLOGY
6.1. Defining the condition and causes of damage
The present condition of “Poplar Tree of Horror”, as one of the most poignant witnesses
of Ustashe atrocities committed in World War II, is very bad, and requires taking of the
urgent measures on conservation and restoration.
The poplar tree is located on a small grass plateau, where the Una flows into the Sava,
along the local road.
The age of the tree as well as high concentration of moist, present in the place where the
tree grew contributed to rapid decomposition of the tree core. In 1978 the poplar was
knocked down in a storm, after which it lost its vital functions. It was easy for the tree to
crumble down in the storm, because the central part of the trunk had rotten, and was not
capable of holding a burden of big crown. Most branches were broken as the tree fell down
on the soil.
In the next year, 1979, works were carried out on protection and conservation of the tree
and of the metal wedges that were preserved on it. These works significantly helped slow
down the process of destruction and rotting. Parts were preserved by impregnation and
protected against further decomposition by laying the appropriate coatings.
Poplar was placed horizontally, on three metal bearers, specially designed for this purpose.
Such a way of presentation proved to be extremely good.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 16/34
16
Conservation restoration works on Poplar Tree of Horror were carried out by the
Laboratory for Protection of Wood R.O. Sipad – IRC. OOUR ''Sumaprojekt'' from Sarajevo
with participation of R.O. ''Vranica'' – Sarajevo, OOUR ''Bobovac''- Vares.
The dimensions of the tree Poplar of Horror, placed on horizontal bearers:
- northern side; (Sava river) length 16.9 meters; height 4.75 meters;
circumference 4.6 meters
- southern side; length 16.7 meters;
- eastern side; (top) width 12.3 meters
- western side; (lower part of the trunk) circumference 5.7 meters
- branch relying on the ground ; length 11.6 meters; circumference 1.73
meters
Bad condition of the Poplar Tree has even more deteriorated after September 1995, when
it was hit by an inflammable projectile from the other bank of the Sava river, i.e. direction of
the Republic of Croatia.
The strong detonation dislocated the tree from where it lay on the steel construction
bearer.
The fire that broke out completely destroyed conservatory protection from year 1979.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 17/34
17
The northern part of the tree was burnt down during the fire, and the rest was very much
damaged and partly destroyed.
The central part of the trunk of the tree from the western side was burnt on the surface, andin the sections that were not caught by fire large structural crevices were formed. On those
surfaces there are colonies of moss and Iceland moss the growth of which is helped by
hydroscopic structure of the tree and the lack of the protection layer.
During the explosion the longest branch from the southern side was dislocated from the
bearer. It also broke then and because of its weight and length is recumbent on the ground
from which it directly soaks in moist, hence the process of rotting and decaying is even more
accelerated.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 18/34
18
The remains of the tree that were not caught up by fire lost their stable structure, so that
surface and internal crevices were formed.
After destruction of conservation protection during fire, the tree was exposed toatmospheric impacts without any obstructions. The biggest problems are created during the
winter by frost, and during the summer by the sun. Big temperature oscillations during the
year and direct exposure to atmospheric impacts contribute to accelerated process of decay.
The structure of the remains of the tree is currently in a very bad condition.
Most characteristic damage according to the degree of the risk includes the following:
− about 18% of the tree was destroyed in fire
− the trunk and the branches cracked in several places
− the structure of the tree is endangered, crevices of horizontal, vertical and
diagonal type are visible,
− on certain surfaces there are visible layers of moss, Iceland moss and plants
− surface layers of the tree are falling off
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 19/34
19
Auxiliary bearers additionally secured the stability of the tree in its horizontal position.
Corrosion is visible on a larger surface.
Access part of the plateau near the “Poplar Tree of Horror” is in bad condition, as well as
the plateau itself, which is indicative of its general bad condition.
6.2. Conservation-restoration works and the methodology
Conservation-restoration works that would relate to “Poplar Tree of Horror” would
first of all imply consolidation of the structure of the tree that is endangered, which is, due to
its condition at risk of being completely destroyed.
General methodology relating to this problematic arising from our preliminary
research works implies the following set of procedures:
A. research works aimed at determining previously used chemicals, as well as the
condition of the structure of the tree by screening and sampling
Taking samples at the beginning of the works, and making analyses on the spot or in
an appropriate laboratory. Determine whether there are traces of original protection.
Use those samples later as points of reference in monitoring the condition.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 20/34
20
B. securing the peripheral parts of the tree and preserved cracked branches
Peripheral parts of the tree are the parts that are most exposed to decay, due to the
composition of the trunk itself, where the fibers are cut horizontally and do not have
natural protection. This is where the tree is the most porous and therefore specific
treatment should be applied to those parts.
The branches that are cracked, and especially the longest branch on the southern side
which is, after the explosion, lying on the ground, because of its weight, should be
fixed. Fixing of the branch should be done through the central part by using tube-like
immobilizers made of stainless steel. Another method that can be applied is injecting
the mass that contains reinforcement particles in the central part of the tree into a
previously drilled channel.
As for the longest branch that was broken, after internal immobilization, an auxiliary
bearer should be placed on the external side. The bearer should be placed after
bringing the Poplar to the original position.
C. consolidation and immobilization of surface parts of wooden structure and
branches
In order to consolidate the decaying parts of the tree and stop the destructive
processes, the core should be stabilized. In order to make sure that the agent used for
consolidation is of appropriate composition and quality, tests should be carried out on
the spot and based on results most optimum proportions of the solution should be
established. Consolidating agent must have the following characteristics: deep
penetration, hydrophobic protection and the quality of achieved consolidation. On
wooden sections that are in advanced stage of decay due to porosity and the power of
soaking, they should be immersed until saturation, i.e. total impregnation. After that
investigate pressure strength, and carry out crystallization test.
D. removing layers of dirt, moss and mould
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 21/34
21
Surface layers of dirt, moss and mould should be removed by using mechanical and
chemical agents.
Moss and mould should be removed mechanically wherever possible. Chemical
agents should be used only in places where necessary, without allowing the solution
to penetrate into the tree structure, thus enabling a better control.
E. destroying worm hole using insecticides and fungicides
After completed treatment of mechanical and chemical removal of layers of dirt, moss
and mould, apply the fungicide protection agent. Agent should be applied by soaking
with the possibility of application of the prolonged effect method, in order for the
fungicide to penetrate as deeply as possible into the tree structure, and prolong its
effect, all to the end of making sure that the worm hole is destroyed in the most
efficient manner.
F. injecting appropriate injection mass into the internal structure of the tree by using
the special pressure-regulated injectors
Injection mass that is chemically compatible in terms of composition with the original
wood structure is used for filling the cracks, while aggregate as filler must have fine
granulation. When injected under a certain pressure, the mass penetrates into the
deepest pores. Consolidation of structural cracks is done by the methodology from
previously described procedures and applications. Micro- and macro- cracks must be
sealed because structural compactness as well as the stability of the bearer is restored
and precipitation is prevented from penetrating into the core of the tree.
G. removing the burnt parts of the tree
The conservation approach itself allows treating the burnt parts in two ways:
• Conserve all the burnt parts of the tree and preserve them against further
decaying because they are a witness of past times, or
• Remove the layers of the burnt tree mechanically with the possibility to
control the depth of action. Once the satisfactory level is reached, perform
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 22/34
22
conservatory works. In one section leave the burnt surface for the purpose of
display.
H. filling the missing sections with appropriate retouch substances
Solutions and fillers, the composition and properties of which, i.e. compatibility,
diffusion, appearance and colour conform to the original structure and textures, are
used to fill the damaged sections.
For this type of works it is the best to use the aggregate of the same origin and
composition. Bigger damage should be filled up to 1 mm from the surface of treated
section, then wait for a certain time, and then apply the retouch mass that will adjust
the original section and the filling in terms of colour. Final structural treatment is
done by hand polishing.
I. protective impregnation
Final protective impregnation is done by agents specifically prepared for this purpose.
By their chemical composition, the agents must be compatible with all the solutions
applied to that point.
The type of protective impregnation that will be used must have high resistance to
frost, high temperatures and must be waterproof and have good wood adhesion.
J. putting the tree back to its original place on the bearer
The tree was dislocated from its original horizontal position. After the explosion, the
tree was moved in the direction north-south along a 50-70 cm stretch.
The tree was placed horizontally on three vertical bearers. The metal bearers have
smaller auxiliary bearers that additionally secured stability of horizontally placed tree.
The tree should be brought back to its original position for security reasons.
This procedure should be done with the use of cranes that will have an especially
prepared cable with safety pads on their ends. Failing to comply with f these would
cause the Poplar to break because of the length of the tree and unbalanced weights.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 23/34
23
This is a very complex process and requires special preparation of both the tree and
mechanization.
K. protection of the metal bearer with appropriate means
The poplar is relying on three metal bearers.
The bearers are made of steel and are presently in relatively good condition.
Necessary works relating to the metal structure would imply:
- removal of the corrosion layers by anti-corrosion agents made by renowned
manufacturer
- putting the basic layer on the cleaned metal part
- putting the protective layer on the metal part
- putting the final layer of metal protection
L. making of the roof structure above the Poplar Tree of Horror
Making of the roof above the Poplar Tree of Horror is one of the most
necessary protection measures. Once the conservation restoration work is done, the
cultural asset itself will be protected, however it will not have appropriate quality
conditions. By making a roof structure over the Poplar as well as around it, direct
influence of rain and frost will not be possible during the winter, while in the summer
direct exposure to the sun and high temperatures will be avoided.
The roof structure will also help prolong the period of effect of quality
conservation restoration protection.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 24/34
24
6.3.Technical documentation
drawings:
• southern side of the Poplar Tree of Horror (drawing 1)
• western side of Poplar Tree of Horror (drawing 2)
• drawing of the construction bearers (drawing 3)
• southern side –burnt sections(drawing 4)
• western side-burnt sections (drawing 5)
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 25/34
25
7. PRICED BILL OF QUANTITIES - STAGE A
Based on the above-mentioned works, the following project values are derived, including
the following items:
Type of works Project value
1. Research works on determining previously used
chemicals, as well as the condition of structure of the
tree by scanning and sampling
950 КМ
2. Securing the edge parts of the tree and the preserved
cracked branches
5600 КМ
3. Consolidation and immobilization of surface parts of
wooden structure and branches
7230 КМ
4. Removing the layers of dirt, moss and mould by
chemical agents and mechanically
3700 КМ
5. Destroying worm hole by insecticides and fungicides 2200 КМ
6. Injecting the appropriate injection mass in the internal
structure of the tree using special pressure-regulated
injectors
8800КМ
7. Removing the burnt parts of the tree 1200 КМ
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 26/34
26
Total project value of the works amounts to 44 480 КМ
8. Filling the missing sections with appropriate retouch
mass
11300 КМ
9. Protective impregnation 2300КМ
10. Returning the tree to the original place on the bearer 1200 КМ
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 27/34
27
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 28/34
28
STAGE B
8. EXPERT OPINION ON THE STABILITY OF STEEL
BEARERS OF POPLAR OF HORROR
Poplar Tree of Horror relies on three steel bearers. Steel bearers were made of UNP
bearers welded into a case bearer, and form three independent frames.
Frames are founded via the concrete-made foundations.
Based on the visual inspection of the bearers we can say that there is certain damage on them
that will be described in the text below.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 29/34
29
The condition of concrete foundations has not been checked, i.e. the foundations have
not been dug out. Considering the relatively low level of load exerted on the foundations we
can say with high degree of certainty that the foundations of the steel frames are in the
satisfactory condition.
The following damage has been observed on steel frames:
- Surface corrosion. Protective paint has come off
in a number of places, in which corrosion
appeared. The degree of corrosion is not such to
significantly impair the cross section, or to
endanger the stability of elements. Although the
stability of steel frames is not endangered, all
steel elements must be cleaned from corrosion
and coated with appropriate anti-corrosive
protection. Cleaning of elements from corrosion
may be done by sandblasting until the metal glow is achieved.
- Holes on steel elements made by shell pieces. This type of damage is spread and is
present on almost all steel elements. Holes made by shell pieces are not of the
nature to endanger the stability of the construction. The areas around this damage
show the presence of corrosion of steel. This damage can be repaired by cleaning
the steel by sandblasting until the metal glow is achieved, and then by filling the
hole with adequate putty, cutting the area around the hole, and weld the “stain” of
sheet metal. After welding, the weld joint should be ground so that after coating
with anti-corrosive protection the colour of the repair area is invisible. It is
noteworthy that this type of damage does not need to be repaired but can be left as
a testimony of a past time. In that case only corrosion should be cleaned and anti-
corrosive protection applied.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 30/34
30
- Local deformities of horizontal steel-made bearers. This type of damage is of local
nature and has been caused by overloading in certain places. Having in mind
relatively low level of load, as well as the big size of steel frames, we believe that
this damage does not jeopardize the stability of frames. No activities on removing
this damage have been proposed.
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 31/34
31
- Deformities of vertical steel bearers. This type of damage is manifested through
dilation of case-like bearers as a consequence of filling the cases with rain, and
freezing of water in them. Damage would not be removed, but it is necessary to
place the steel lid from the upper side of the case in order to prevent penetration of
precipitation in the future.
- Having in mind that the poplar was moved from its original place (which is a
consequence of the direct hit of the shell), certain steel props have lost their
function, and need to be removed and replaced by the new ones that will be
functional. This is done by cutting the existing steel props, after which the
connection area should be ground up to the case-like bearers and the new props
should be placed in an appropriate area, which would be determined on the spot.
- The foundation construction has not been dug, so that it was not possible to
inspect steel in the area of connection with the foundation construction. The
assumption is that these areas were affected by surface corrosion, and that it isnecessary to dig out the area around the steel posts to reach concrete, clean steel
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 32/34
32
from corrosion, by sandblasting until the metal glow is achieved, and carry out
adequate anti-corrosive protection.
Taking into account the damage listed above, we can conclude that the stability of the
steel bearers themselves is not at risk, and that the observed damage is a consequence of
exposure of the structure to atmospheric impact and vandalism. In order to prevent corrosion
and other type of damage from spreading, the above activities should be undertaken.
8.2. Priced bill of quantities
All the above works may be categorized in a number of groups:
Type of works Project value
1. Sandblasting of steel elements until the metal glow
is achieved.
500 КМ
2. Repairing geometrical irregularities by laying putty
with all necessary actions including rubbing down
until the area is flat with the basic material.
200 КМ
3. Removing steel props and replacing them with
other, together with placing steel lids and other
small-scale welding and cutting.
250 КМ
4. Protection of steel elements by anti-corrosion
coatings
200 КМ
5. Painting the steel elements with paint that will be
determined at a later stage
150 КМ
Based on the cost determined above for individual
items, we can say that its amount for activities on the steel
construction would total to about 1300 КМ
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 33/34
33
At the same time, we should underline the need to make a roof structure that would
protect the Poplar. The roof structure would be constructed according to a separate project.
Type of works Project value
6. If the roof structure is open from all sides (which is
the most inexpensive solution) for the presumed
dimensions of the roof structure of 25/15 meters,
the estimate is that the value of works on its
construction would be about 250 КМ/m2
95000 КМ
The total amount of the above-mentioned items is 96300КМ
9. FUNDS NECESSARY FOR PERFORMING THE WORKS FOR
STAGES A AND B
Based on the above-mentioned priced bill of quantities, we arrived at the following:
Value of works for Stage A 44 480 КМ
Value of works for Stage B 96 300 КМ
-----------------
Total amount is 140 780 КМ
8/8/2019 Projekat - Topola Uzasa English
http://slidepdf.com/reader/full/projekat-topola-uzasa-english 34/34
10. TIME PLANNED FOR PERFORMING WORKS
The time period envisioned for carrying out of conservation – restoration works on Poplar
Tree of Horror in Donja Gradina Memorial Area according to Stages A and B is 150 working
days.
Protocol no. 07/1.22/624-666/09.
Banja Luka, on 20 August, 2009
Project design manager:
Milica Kotur, MA
BSc. conservation-restoration
cc:
1. Minister in the RS Ministry of Education and Culture
2. Assistant minister in the RS Ministry of Education and Culture
3. Director of the Institute
4.
Department of Research and Valorization of the Institute5. Public Institution Donja Gradina
6. files
Recommended