View
219
Download
2
Category
Preview:
Citation preview
NGS-D320
User Guide
NGS-D320 LiteNGS-D320 Pro
Applicable for software versions V210 and higher
K59031290029092016
Barco NVPresident Kennedypark 35 8500 Kortrijk BelgiumPhone +32 56233211Fax +32 56262262Support wwwbarcocomensupportVisit us at the web wwwbarcocom
Printed in Belgium
Table of contents
TABLE OF CONTENTS
1 Welcome 311 About the product 312 About this manual 413 Whatrsquos in the box 4
2 Product information 521 Use cases 5211 Media modes 5212 Control modes 7
22 Models 8221 Lite amp Pro 8
23 Features 8231 Resources 9232 EDID 9233 Network 11234 Streaming 11235 Video 12236 Audio 15237 USB HID 15
3 Installation 1731 Front view 1732 Rear view 1933 Start up 20
4 Operation 2141 Introduction 2142 Web interface 21421 Introduction 21422 Browser support 21423 WebUI overview 21424 Login 22
43 Discovery 23431 Introduction 23432 Barco Device Discovery Tool 24433 Discovery via OSD 24434 Web Interface Discovery 25435 Identification button 26
44 Device info 26441 Introduction 26442 Info 27443 Diagnostics 28444 Administration 29445 Software upgrade 31446 Help 31
45 Settings 32451 Introduction 32452 Network settings 324521 IP settings 334522 Managed mode 344523 Unmanaged mode 354524 SNMP settings 35
453 Encoder settings 354531 Overview 354532 Audio 354533 DVI InDP InHDMI In 364534 HDMI Audio In 37
K5903129 NGS-D320 29092016 1
Table of contents
4535 USB Host 37454 Decoder settings 384541 Overview 384542 Audio 384543 DVI OutDP OutHDMI Out 384544 HDMI Audio Out 394545 USB Peripherals 40
5 Cleaning your device 4151 Cleaning procedure 41
6 Repackaging instructions 4361 Device repacking 43
7 Service activities 4571 Reaching the local Barco helpdesk and online support 4572 Online product support 4673 Reporting an issue in SalesForcecom 46
8 Important information 4981 Safety information 4982 Environmental information 5083 Regulatory compliance information 5284 EMC notice 5385 Explanation of symbols 5386 Legal disclaimer 5587 Technical Specifications NGS-D320 Lite 5588 Technical Specifications NGS-D320 Pro 5789 Open source license information 58
2 K5903129 NGS-D320 29092016
1 Welcome
1 WELCOME
11 About the productDevice typeThank you for choosing this Barco device the Network Graphics Source (NGS)
The NGS-D320 is a versatile and powerful networked H264 encoder and decoder Its elegant designsmall form factor and silent operation allows the device to be used in any situation both in office environ-ments and in 247 mission critical applications Due to its versatility the NGS-D320 can be configured atruntime as an encoder or a decoder for DVI HDMI and DisplayPort content with or without audio Thecombination of these functions with integrated keyboard and mouse control in a single unit is ideal tocreate a seamless environment for application sharing simulation and training
Key features
bull Superb Visual ExperienceThe NGS-D320 comes with Barcorsquos latest image processing engine which provides the best scalingand color space conversion algorithms on the market today When distributing graphics the encoderpreserves even the smallest details making it suitable to encode images like spreadsheets or singlepixel line diagrams
bull Simple IntegrationBy default the device will automatically start streaming whenever a valid input signal is connectedThe stream is automatically set up using the most optimal settings based on input resolution andbandwidth In addition the discovery page of the web interface gives an overview of all availabledevices in the network making system configuration easy
bull No Adjustment NeededWith automatic EDIDmanagement and scaling at the decoding side the best experience in distributinggraphics and video over IP is guaranteed Fiddling with displays to get a good picture is thus unnec-essary Switching from one source to another is fluent and does not require the display to re-syncto the new signal The decoder can also both upscale and downscale to match the preferred displaysettings
bull Performance- NGS-D320 Lite The NGS-D320 Lite used as an encoder comes with a dual link DVI a HDMI anda DisplayPort 11a input All inputs support resolutions up to 4096x2160(DCI) and feature activepass-through connectivity Although encoding in full frame rate by default the device also supportslower frame rates This allows you to define the balance between quality and required bandwidthThe encoder latency is below 40ms allowing an end to end latency of below 100ms (note latencydepends on the selected profile)
- NGS-D320 ProThe NGS-D320 Pro has two independent channels which can each be configured individually asencoder or decoder As encoder it exposes maximum two inputs selectable out of a dual link DVIan HDMI 14a and a DisplayPort 11a input All inputs support resolutions up to 4096x2160 (DCI)and feature active pass-through connectivity Although encoding in full frame rate by default thedevice also supports lower frame rates This allows you to define the balance between quality andrequired bandwidth The encoder latency is below 40ms allowing an end to end latency of below100ms (note latency depends on the selected profile)
CAUTION Read all the safety information (Safety information page 49) before oper-ating your NGS-D320
K5903129 NGS-D320 29092016 3
1 Welcome
12 About this manualUser GuideThis User Guide describes how to install and use the Barco device NGS-D320
13 Whatrsquos in the boxNGS-D320 box contentYour Barco NGS-D320 comes withbull Quick Start Guidebull mains cable (EU)bull mains cable (US)bull external power supply (12V60W)
Keep your original packaging It is designed for this device and is the ideal protectionduring transport
4 K5903129 NGS-D320 29092016
2 Product information
2 PRODUCT INFORMATION
21 Use cases
An NGS-D320 device enables hardware-accelerated KVMA-over-IP using standard 1GIPv4 networks It is connected to the network for transporting Audio Video and control
211 Media modes
Different media modesThe device can stream media in 3 different media modes to support various use cases
These 3 media modes are supported
bull Encoderbull Decoderbull Local
A brief description for each media mode is given below
EncoderThe device is typically connected to a desktop PC or server
The corresponding decoder can be
bull Another NGS-D320 devicebull A software based decoder
Install your NGS-D320 as an encoder
To decode use software decoding on a PCserver (eg VLC Media Player ) andor use another NGS-D320 as a decoder
This is illustrated below
1
2 3
4
5
6
7
8
9
9
9
Image 2-1Encoder installation
1 PC server2 NGS-D320 (encoder)3 Switch4 NGS-D320 (decoder)5 PC (SW decoder)6 Audio signal
K5903129 NGS-D320 29092016 5
2 Product information
7 Video signal8 USB HID9 Data (network)
Audio video and USB connections are made from the PC to the NGS-D320
The video content flows from the PCserver to the NGS-D320 the NGS-D320 encodes the video andthen the video is streamed onto the IP network
The audio content can be bi-directional audio can be sent to or received from the NGS-D320The USB peripheral port of the NGS-D320 connects to an USB host port on the PCserver The NGS-D320 emulates an USB HID device and events are sent from the NGS-D320 to the PCserver
DecoderThe device is typically connected to one or two screens Next to the screens the device can also beconnected to a headsetspeakermicrophone a keyboard and a mouse
The corresponding encoder can be
bull Another NGS-D320 devicebull Another Barco device compatible with the NGS-D320
Refer to the specific Barco Systems with NGS-D320 devices for compatible products
1
2
3 4
5
6 7
8
9
6
6
Image 2-2Decoder installation
1 NGS-D320 (encoder)2 Barco device or PCserver3 Switch4 NGS-D320 (decoder)5 Screen headsetspeakermicrophone keyboard or mouse6 Data (network)7 Audio signal8 Video signal9 USB HID
The video interfaces are connected to the screen(s)The audio interfaces are connected to a headset or speakers and a microphone can be connected to theNGS-D320
The keyboard and mouse connect to the USB host interfaces of the NGS-D320
LocalThis mode is a combination of the encoder amp decoder mode
The device is typically connected locally at a desktop position The device sits between the PCserverand the screens headsetspeakermicrophone keyboard and mouse The video audio amp USB cablesconnect from both ends to the NGS-D320 device
These inputs are locally looped through the device
The NGS-D320 device plugs into the network and is capable of streaming amp receiving network traffic si-multaneously
Install your NGS-D320 as illustrated below
6 K5903129 NGS-D320 29092016
2 Product information
1
2
3
4
6 7 8
5
6 7 8
Image 2-3Encoder and decoder installation
1 Screen headsetspeakermicrophone keyboard or mouse2 NGS-D320 (local)3 Barco device or PCserver4 Switch5 Data (network)6 Audio signal7 Video signal8 USB HID
Keyboard local settings To make sure all keys are operable the physical keyboardlayout at decoder side should match the keyboard configuration at encoder side (onPCserver)
212 Control modes
Different control modesThe device can be controlled in 2 modes
bull Locally or Unmanaged modebull Centrally or Managed mode
Unmanaged modeIn this mode the device is used stand-alone
Each device is controlled amp operated locally through its onboard web user interface
See Operation page 21 for details on how to configure amp operate the device
Managed modeIn this mode the device is used in a system
Each device is controlled amp operated centrally via a system controller which communicates with the devicethrough the device API
See the User Manual of the respective system on how to configure amp operate the device within the systemcontext
K5903129 NGS-D320 29092016 7
2 Product information
22 Models
221 Lite amp Pro
DifferencesThe NGS-D320 comes in 2 flavours a Lite and a Pro versionThemain difference between the 2models is the number of simultaneous video streams and display headsthat they support
Refer to Technical Specifications NGS-D320 Lite page 55 and Technical Specifications NGS-D320Pro page 57 for more details of the specifications
Model Lite ProNumberof H264streams
1 up to 2H264 streams
Use cases Encoder orDecoder
Local (EncoderDecoder) or
Dual channel encoder or
Dual channel decoderNumber ofsource inputs
1 up to 2Display heads1
Numberof displayoutputs
1 up to 2
Local use case NA Can be set up to encode 1 H264 stream ANDdecode 1 H264 stream from independentsources simultaneously
Level 51 NA Can only encode OR decode 1 L51 stream(up to 4K resolution) not 2
Maximum resolution 2560x1600 30fps
4096x2160 15fps
2 streams 2560x1600 30fps
1 stream 2560x1600 60fps
1 stream 4096x2160 30fps
Dual quality NA Can encode a single source (less than L51)twice in 2 different qualities
Dual channel NA Can encode both a DVI and a DisplayPortinput simultaneously
Priority principle If an input stream has L51 (4K) only one encoding shall be active
23 FeaturesOverviewThe device supports audio video amp USB media types on the network
In this section an explanation is given on the various features per media type as well as on the networkspecific features
Refer to Operation page 21 on how to configure the NGS-D320 for these features
1 Only one 4K H264 stream can be encoded or decoded at a time
8 K5903129 NGS-D320 29092016
2 Product information
231 Resources
Device behaviourDepending on the model an NGS-D320 has limited audio amp video encoding and decoding resources
A resource utilization algorithm is present on the NGS-D320 that ensures that the device will alwaysbehave in the same way when it is configured in the same way
Priority principleResources are not granted on a ldquofirst come first serverdquo principle but on a priority principle
The following priority principle is valid
bull Encoding always gets priority over decodingbull Encoding will be in order of priority DVI HDMI DPbull If an input stream is configured to use an L51 profile (eg for 4K) only encoding shall be activebull For Pro devices the first stream of an input type will have priority over second stream of the same
input type
These principles apply dynamically and in real-time depending on the actual device status These princi-ples are valid both for audio amp video
Some examples on the priority principle
bull A device is configured to encode 2 inputs (eg 1 DP and 1 DVI) and also configured to decode 1output (eg 1 DVI or 1 DP)When the 2 inputs are active (active syncs detected) the device will only encode decoding will bedisabledIf one of the 2 inputs drops (no active sync detected) the decoding will start automatically
bull A device is configured to encode 1 DP input and 1 DVI inputIf the DP input is 4K resolution (L51) then only the DP input encoding will be activeIf the DP input resolution changes to 1920x1080 then the DVI input encoding will automatically acti-vate
bull A Pro device is configured to encode 1 DP input in 2 qualities and 1 DVI inputThe DVI will be encodedOnly the first configured DP stream will be encoded
ReportingThe actual status of resource utilization is reported continuously via Diagnostics
232 EDID
EDID supportThe NGS-D320 supports EDID at both the input and ouput The EDID can be setup for each input andoutput individually and independently
InputThe EDID at the input is the EDID as seen by the PC This is typically setup at the encoder side Referto Encoder settings page 35 on how to configure
At the input 2 settings are supported
K5903129 NGS-D320 29092016 9
2 Product information
1 Default4 timings will be supported on the source PC with 1920x1200p60 as preferred timing
1920x1200p60
1920x1080p60
2560x1600p603840x2160p30
2 SpecificIn this setting only one specific timing will be providedThe specific timing can be selected out of a list of 46 timings
640x480p50 1176x664p50 1280x960p50 1440x900p50 1920x1080p50 2560x1440p50
640x480p60 1176x664p60 1280x960p60 1440x900p60 1920x1080p60 2560x1440p60
800x600p50 1280x720p50 1280x1024p50 1600x1024p50 1920x1200p50 2560x1600p50800x600p60 1280x720p60 1280x1024p60 1600x1024p60 1920x1200p60 2560x1600p601024x768p50 1280x768p50 1344x1008p50 1600x1200p50 1920x1440p50 3840x2160p251024x768p60 1280x768p60 1344x1008p60 1600x1200p60 1920x1440p60 3840x2160p301152x864p50 1280x800p50 1360x768p50 1680x1050p50 2048x1536p50 4096x2160p251152x864p60 1280x800p60 1360x768p60 1680x1050p60 2048x1536p60 4096x2160p30
The connected source device is free to ignore the EDID of the NGS-D320 When anothertiming is received the NGS-D320 will adapt to this timing as long as it is one of the 48supported timings
Output timingBy default the timing on the output video connector will be set to the first (preferred) detailed timing inthe EDID of the display The timing can also be set to a specific timing ignoring the EDID of the display
This is typically setup at the decoder side The decoded video will be resized and frame rate convertedto be shown full screen on the connected display When resizing aspect ratio will be kept
Refer to Decoder settings page 38on how to configure
At the output 3 modes are supported1 Preferred timing
In this setting the output timing of the device will be the first detailed timing descriptor in the EDID ofthe attached display
2 StandbyIn this setting the output syncs are disabled to make the connected display go to standby
3 SpecificIn this setting the NGS-D320 will not read the EDID from the connected display but will force theoutput as selected out of the 45 supported timings
Loop throughIt is possible to loop through the video amp audio from input to output connector
The loop through behavior is depending on the decoder settingsIf decoding is active no loop through shall be available
If decoding is not active (eg on an encoder) then the output will be a loop through of the input
The loop through will be active
10 K5903129 NGS-D320 29092016
2 Product information
bull 05 seconds after the input is connectedbull 2 seconds after the decoding is disabled
233 Network
DiscoveryNGS-D320 devices can be discovered on the network using the mDNS protocol
Refer to Discovery page 23 on how to discover an NGS-D320
IP addressingThe NGS-D320 supports IPv4 addressing
The IP address can be dynamically configured using DHCP or can be configured to static
If no DHCP is present and no static config is available the device will fall back to linklocal addressing
The NGS-D320 can connect to an NTP (Network Time Protocol) server
All media traffic will be timestamped according to this reference time
If no NTP server is present the media will be timestamped in line with the device clock (starting at 1 Jan1970) The device clock is reset after every reboot
The NGS-D320 can connect to a DNS (Domain Name Service) server
Refer to Network settings page 32 on how to configure NGS-D320 network settings
PortsThe table below lists the ports used for the various protocols on the NGS-D320
Port ProtocolTCP 443 https for web interface and APITCP 554 RTSPTCP 5901 VNC for keyboard amp mouse forwarding from decoder to encoderUDP 5004 RTP audio amp video streaming (5004 is the default port changeable by user)UDP 9875 Session announcements (SAP) on multicast address 2242127254
These ports need to be open on the network infrastructure to ensure proper operation
234 Streaming
Stream controlThe NGS-D320 supports 2 methods to control stream flow1 RTSP
The NGS-D320 supports RTSP (Real Time Streaming Protocol) and runs an RTSP server to manageconnections Connection to the NGS-D320 streams can be done via RTSP clientsBoth RTSP unicast amp multicast is supported
2 SAPThe NGS-D320 supports SAP (Session Announcement Protocol) and sends out SAP announcementsWhen subscribing to the SAP multicast address 2242127254 the SAP message of an NGS-D320will be available and will allow to connect to an NGS-D320 multicast stream
Media streamThe NGS-D320 uses RTP (Real Time Protocol) to stream media
K5903129 NGS-D320 29092016 11
2 Product information
Each encoded stream can have 2 destination addressesports
Device type Number of H264 streams Destination addressesportsNGS-D320 Lite 1 stream Stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSPNGS-D320 Pro 2 streams
bull from 2 different video inputs orbull the same video input encoded
with different quality
Each stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSP
SDPThe streams are described via SDP (Session Description Protocol) For each stream an SDP will beavailable
Refer to Encoder settings page 35 and Decoder settings page 38 to setup streamingon NGS-D320
235 Video
Video formatThe NGS-D320 encodes and decodes DVI HDMI and DP connections tofrom compressed H264 IPtraffic
The H264 stream is
bull IAW RFC3984 (RTP Payload Format for H264 Video)bull YUV420 format with 8-bit colordepth
Encoder profilesThe NGS-D320 encoder supports a number of H264 encoder profiles with varying stream profile levelbitrate framerate and maximum resolution
12 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
Barco NVPresident Kennedypark 35 8500 Kortrijk BelgiumPhone +32 56233211Fax +32 56262262Support wwwbarcocomensupportVisit us at the web wwwbarcocom
Printed in Belgium
Table of contents
TABLE OF CONTENTS
1 Welcome 311 About the product 312 About this manual 413 Whatrsquos in the box 4
2 Product information 521 Use cases 5211 Media modes 5212 Control modes 7
22 Models 8221 Lite amp Pro 8
23 Features 8231 Resources 9232 EDID 9233 Network 11234 Streaming 11235 Video 12236 Audio 15237 USB HID 15
3 Installation 1731 Front view 1732 Rear view 1933 Start up 20
4 Operation 2141 Introduction 2142 Web interface 21421 Introduction 21422 Browser support 21423 WebUI overview 21424 Login 22
43 Discovery 23431 Introduction 23432 Barco Device Discovery Tool 24433 Discovery via OSD 24434 Web Interface Discovery 25435 Identification button 26
44 Device info 26441 Introduction 26442 Info 27443 Diagnostics 28444 Administration 29445 Software upgrade 31446 Help 31
45 Settings 32451 Introduction 32452 Network settings 324521 IP settings 334522 Managed mode 344523 Unmanaged mode 354524 SNMP settings 35
453 Encoder settings 354531 Overview 354532 Audio 354533 DVI InDP InHDMI In 364534 HDMI Audio In 37
K5903129 NGS-D320 29092016 1
Table of contents
4535 USB Host 37454 Decoder settings 384541 Overview 384542 Audio 384543 DVI OutDP OutHDMI Out 384544 HDMI Audio Out 394545 USB Peripherals 40
5 Cleaning your device 4151 Cleaning procedure 41
6 Repackaging instructions 4361 Device repacking 43
7 Service activities 4571 Reaching the local Barco helpdesk and online support 4572 Online product support 4673 Reporting an issue in SalesForcecom 46
8 Important information 4981 Safety information 4982 Environmental information 5083 Regulatory compliance information 5284 EMC notice 5385 Explanation of symbols 5386 Legal disclaimer 5587 Technical Specifications NGS-D320 Lite 5588 Technical Specifications NGS-D320 Pro 5789 Open source license information 58
2 K5903129 NGS-D320 29092016
1 Welcome
1 WELCOME
11 About the productDevice typeThank you for choosing this Barco device the Network Graphics Source (NGS)
The NGS-D320 is a versatile and powerful networked H264 encoder and decoder Its elegant designsmall form factor and silent operation allows the device to be used in any situation both in office environ-ments and in 247 mission critical applications Due to its versatility the NGS-D320 can be configured atruntime as an encoder or a decoder for DVI HDMI and DisplayPort content with or without audio Thecombination of these functions with integrated keyboard and mouse control in a single unit is ideal tocreate a seamless environment for application sharing simulation and training
Key features
bull Superb Visual ExperienceThe NGS-D320 comes with Barcorsquos latest image processing engine which provides the best scalingand color space conversion algorithms on the market today When distributing graphics the encoderpreserves even the smallest details making it suitable to encode images like spreadsheets or singlepixel line diagrams
bull Simple IntegrationBy default the device will automatically start streaming whenever a valid input signal is connectedThe stream is automatically set up using the most optimal settings based on input resolution andbandwidth In addition the discovery page of the web interface gives an overview of all availabledevices in the network making system configuration easy
bull No Adjustment NeededWith automatic EDIDmanagement and scaling at the decoding side the best experience in distributinggraphics and video over IP is guaranteed Fiddling with displays to get a good picture is thus unnec-essary Switching from one source to another is fluent and does not require the display to re-syncto the new signal The decoder can also both upscale and downscale to match the preferred displaysettings
bull Performance- NGS-D320 Lite The NGS-D320 Lite used as an encoder comes with a dual link DVI a HDMI anda DisplayPort 11a input All inputs support resolutions up to 4096x2160(DCI) and feature activepass-through connectivity Although encoding in full frame rate by default the device also supportslower frame rates This allows you to define the balance between quality and required bandwidthThe encoder latency is below 40ms allowing an end to end latency of below 100ms (note latencydepends on the selected profile)
- NGS-D320 ProThe NGS-D320 Pro has two independent channels which can each be configured individually asencoder or decoder As encoder it exposes maximum two inputs selectable out of a dual link DVIan HDMI 14a and a DisplayPort 11a input All inputs support resolutions up to 4096x2160 (DCI)and feature active pass-through connectivity Although encoding in full frame rate by default thedevice also supports lower frame rates This allows you to define the balance between quality andrequired bandwidth The encoder latency is below 40ms allowing an end to end latency of below100ms (note latency depends on the selected profile)
CAUTION Read all the safety information (Safety information page 49) before oper-ating your NGS-D320
K5903129 NGS-D320 29092016 3
1 Welcome
12 About this manualUser GuideThis User Guide describes how to install and use the Barco device NGS-D320
13 Whatrsquos in the boxNGS-D320 box contentYour Barco NGS-D320 comes withbull Quick Start Guidebull mains cable (EU)bull mains cable (US)bull external power supply (12V60W)
Keep your original packaging It is designed for this device and is the ideal protectionduring transport
4 K5903129 NGS-D320 29092016
2 Product information
2 PRODUCT INFORMATION
21 Use cases
An NGS-D320 device enables hardware-accelerated KVMA-over-IP using standard 1GIPv4 networks It is connected to the network for transporting Audio Video and control
211 Media modes
Different media modesThe device can stream media in 3 different media modes to support various use cases
These 3 media modes are supported
bull Encoderbull Decoderbull Local
A brief description for each media mode is given below
EncoderThe device is typically connected to a desktop PC or server
The corresponding decoder can be
bull Another NGS-D320 devicebull A software based decoder
Install your NGS-D320 as an encoder
To decode use software decoding on a PCserver (eg VLC Media Player ) andor use another NGS-D320 as a decoder
This is illustrated below
1
2 3
4
5
6
7
8
9
9
9
Image 2-1Encoder installation
1 PC server2 NGS-D320 (encoder)3 Switch4 NGS-D320 (decoder)5 PC (SW decoder)6 Audio signal
K5903129 NGS-D320 29092016 5
2 Product information
7 Video signal8 USB HID9 Data (network)
Audio video and USB connections are made from the PC to the NGS-D320
The video content flows from the PCserver to the NGS-D320 the NGS-D320 encodes the video andthen the video is streamed onto the IP network
The audio content can be bi-directional audio can be sent to or received from the NGS-D320The USB peripheral port of the NGS-D320 connects to an USB host port on the PCserver The NGS-D320 emulates an USB HID device and events are sent from the NGS-D320 to the PCserver
DecoderThe device is typically connected to one or two screens Next to the screens the device can also beconnected to a headsetspeakermicrophone a keyboard and a mouse
The corresponding encoder can be
bull Another NGS-D320 devicebull Another Barco device compatible with the NGS-D320
Refer to the specific Barco Systems with NGS-D320 devices for compatible products
1
2
3 4
5
6 7
8
9
6
6
Image 2-2Decoder installation
1 NGS-D320 (encoder)2 Barco device or PCserver3 Switch4 NGS-D320 (decoder)5 Screen headsetspeakermicrophone keyboard or mouse6 Data (network)7 Audio signal8 Video signal9 USB HID
The video interfaces are connected to the screen(s)The audio interfaces are connected to a headset or speakers and a microphone can be connected to theNGS-D320
The keyboard and mouse connect to the USB host interfaces of the NGS-D320
LocalThis mode is a combination of the encoder amp decoder mode
The device is typically connected locally at a desktop position The device sits between the PCserverand the screens headsetspeakermicrophone keyboard and mouse The video audio amp USB cablesconnect from both ends to the NGS-D320 device
These inputs are locally looped through the device
The NGS-D320 device plugs into the network and is capable of streaming amp receiving network traffic si-multaneously
Install your NGS-D320 as illustrated below
6 K5903129 NGS-D320 29092016
2 Product information
1
2
3
4
6 7 8
5
6 7 8
Image 2-3Encoder and decoder installation
1 Screen headsetspeakermicrophone keyboard or mouse2 NGS-D320 (local)3 Barco device or PCserver4 Switch5 Data (network)6 Audio signal7 Video signal8 USB HID
Keyboard local settings To make sure all keys are operable the physical keyboardlayout at decoder side should match the keyboard configuration at encoder side (onPCserver)
212 Control modes
Different control modesThe device can be controlled in 2 modes
bull Locally or Unmanaged modebull Centrally or Managed mode
Unmanaged modeIn this mode the device is used stand-alone
Each device is controlled amp operated locally through its onboard web user interface
See Operation page 21 for details on how to configure amp operate the device
Managed modeIn this mode the device is used in a system
Each device is controlled amp operated centrally via a system controller which communicates with the devicethrough the device API
See the User Manual of the respective system on how to configure amp operate the device within the systemcontext
K5903129 NGS-D320 29092016 7
2 Product information
22 Models
221 Lite amp Pro
DifferencesThe NGS-D320 comes in 2 flavours a Lite and a Pro versionThemain difference between the 2models is the number of simultaneous video streams and display headsthat they support
Refer to Technical Specifications NGS-D320 Lite page 55 and Technical Specifications NGS-D320Pro page 57 for more details of the specifications
Model Lite ProNumberof H264streams
1 up to 2H264 streams
Use cases Encoder orDecoder
Local (EncoderDecoder) or
Dual channel encoder or
Dual channel decoderNumber ofsource inputs
1 up to 2Display heads1
Numberof displayoutputs
1 up to 2
Local use case NA Can be set up to encode 1 H264 stream ANDdecode 1 H264 stream from independentsources simultaneously
Level 51 NA Can only encode OR decode 1 L51 stream(up to 4K resolution) not 2
Maximum resolution 2560x1600 30fps
4096x2160 15fps
2 streams 2560x1600 30fps
1 stream 2560x1600 60fps
1 stream 4096x2160 30fps
Dual quality NA Can encode a single source (less than L51)twice in 2 different qualities
Dual channel NA Can encode both a DVI and a DisplayPortinput simultaneously
Priority principle If an input stream has L51 (4K) only one encoding shall be active
23 FeaturesOverviewThe device supports audio video amp USB media types on the network
In this section an explanation is given on the various features per media type as well as on the networkspecific features
Refer to Operation page 21 on how to configure the NGS-D320 for these features
1 Only one 4K H264 stream can be encoded or decoded at a time
8 K5903129 NGS-D320 29092016
2 Product information
231 Resources
Device behaviourDepending on the model an NGS-D320 has limited audio amp video encoding and decoding resources
A resource utilization algorithm is present on the NGS-D320 that ensures that the device will alwaysbehave in the same way when it is configured in the same way
Priority principleResources are not granted on a ldquofirst come first serverdquo principle but on a priority principle
The following priority principle is valid
bull Encoding always gets priority over decodingbull Encoding will be in order of priority DVI HDMI DPbull If an input stream is configured to use an L51 profile (eg for 4K) only encoding shall be activebull For Pro devices the first stream of an input type will have priority over second stream of the same
input type
These principles apply dynamically and in real-time depending on the actual device status These princi-ples are valid both for audio amp video
Some examples on the priority principle
bull A device is configured to encode 2 inputs (eg 1 DP and 1 DVI) and also configured to decode 1output (eg 1 DVI or 1 DP)When the 2 inputs are active (active syncs detected) the device will only encode decoding will bedisabledIf one of the 2 inputs drops (no active sync detected) the decoding will start automatically
bull A device is configured to encode 1 DP input and 1 DVI inputIf the DP input is 4K resolution (L51) then only the DP input encoding will be activeIf the DP input resolution changes to 1920x1080 then the DVI input encoding will automatically acti-vate
bull A Pro device is configured to encode 1 DP input in 2 qualities and 1 DVI inputThe DVI will be encodedOnly the first configured DP stream will be encoded
ReportingThe actual status of resource utilization is reported continuously via Diagnostics
232 EDID
EDID supportThe NGS-D320 supports EDID at both the input and ouput The EDID can be setup for each input andoutput individually and independently
InputThe EDID at the input is the EDID as seen by the PC This is typically setup at the encoder side Referto Encoder settings page 35 on how to configure
At the input 2 settings are supported
K5903129 NGS-D320 29092016 9
2 Product information
1 Default4 timings will be supported on the source PC with 1920x1200p60 as preferred timing
1920x1200p60
1920x1080p60
2560x1600p603840x2160p30
2 SpecificIn this setting only one specific timing will be providedThe specific timing can be selected out of a list of 46 timings
640x480p50 1176x664p50 1280x960p50 1440x900p50 1920x1080p50 2560x1440p50
640x480p60 1176x664p60 1280x960p60 1440x900p60 1920x1080p60 2560x1440p60
800x600p50 1280x720p50 1280x1024p50 1600x1024p50 1920x1200p50 2560x1600p50800x600p60 1280x720p60 1280x1024p60 1600x1024p60 1920x1200p60 2560x1600p601024x768p50 1280x768p50 1344x1008p50 1600x1200p50 1920x1440p50 3840x2160p251024x768p60 1280x768p60 1344x1008p60 1600x1200p60 1920x1440p60 3840x2160p301152x864p50 1280x800p50 1360x768p50 1680x1050p50 2048x1536p50 4096x2160p251152x864p60 1280x800p60 1360x768p60 1680x1050p60 2048x1536p60 4096x2160p30
The connected source device is free to ignore the EDID of the NGS-D320 When anothertiming is received the NGS-D320 will adapt to this timing as long as it is one of the 48supported timings
Output timingBy default the timing on the output video connector will be set to the first (preferred) detailed timing inthe EDID of the display The timing can also be set to a specific timing ignoring the EDID of the display
This is typically setup at the decoder side The decoded video will be resized and frame rate convertedto be shown full screen on the connected display When resizing aspect ratio will be kept
Refer to Decoder settings page 38on how to configure
At the output 3 modes are supported1 Preferred timing
In this setting the output timing of the device will be the first detailed timing descriptor in the EDID ofthe attached display
2 StandbyIn this setting the output syncs are disabled to make the connected display go to standby
3 SpecificIn this setting the NGS-D320 will not read the EDID from the connected display but will force theoutput as selected out of the 45 supported timings
Loop throughIt is possible to loop through the video amp audio from input to output connector
The loop through behavior is depending on the decoder settingsIf decoding is active no loop through shall be available
If decoding is not active (eg on an encoder) then the output will be a loop through of the input
The loop through will be active
10 K5903129 NGS-D320 29092016
2 Product information
bull 05 seconds after the input is connectedbull 2 seconds after the decoding is disabled
233 Network
DiscoveryNGS-D320 devices can be discovered on the network using the mDNS protocol
Refer to Discovery page 23 on how to discover an NGS-D320
IP addressingThe NGS-D320 supports IPv4 addressing
The IP address can be dynamically configured using DHCP or can be configured to static
If no DHCP is present and no static config is available the device will fall back to linklocal addressing
The NGS-D320 can connect to an NTP (Network Time Protocol) server
All media traffic will be timestamped according to this reference time
If no NTP server is present the media will be timestamped in line with the device clock (starting at 1 Jan1970) The device clock is reset after every reboot
The NGS-D320 can connect to a DNS (Domain Name Service) server
Refer to Network settings page 32 on how to configure NGS-D320 network settings
PortsThe table below lists the ports used for the various protocols on the NGS-D320
Port ProtocolTCP 443 https for web interface and APITCP 554 RTSPTCP 5901 VNC for keyboard amp mouse forwarding from decoder to encoderUDP 5004 RTP audio amp video streaming (5004 is the default port changeable by user)UDP 9875 Session announcements (SAP) on multicast address 2242127254
These ports need to be open on the network infrastructure to ensure proper operation
234 Streaming
Stream controlThe NGS-D320 supports 2 methods to control stream flow1 RTSP
The NGS-D320 supports RTSP (Real Time Streaming Protocol) and runs an RTSP server to manageconnections Connection to the NGS-D320 streams can be done via RTSP clientsBoth RTSP unicast amp multicast is supported
2 SAPThe NGS-D320 supports SAP (Session Announcement Protocol) and sends out SAP announcementsWhen subscribing to the SAP multicast address 2242127254 the SAP message of an NGS-D320will be available and will allow to connect to an NGS-D320 multicast stream
Media streamThe NGS-D320 uses RTP (Real Time Protocol) to stream media
K5903129 NGS-D320 29092016 11
2 Product information
Each encoded stream can have 2 destination addressesports
Device type Number of H264 streams Destination addressesportsNGS-D320 Lite 1 stream Stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSPNGS-D320 Pro 2 streams
bull from 2 different video inputs orbull the same video input encoded
with different quality
Each stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSP
SDPThe streams are described via SDP (Session Description Protocol) For each stream an SDP will beavailable
Refer to Encoder settings page 35 and Decoder settings page 38 to setup streamingon NGS-D320
235 Video
Video formatThe NGS-D320 encodes and decodes DVI HDMI and DP connections tofrom compressed H264 IPtraffic
The H264 stream is
bull IAW RFC3984 (RTP Payload Format for H264 Video)bull YUV420 format with 8-bit colordepth
Encoder profilesThe NGS-D320 encoder supports a number of H264 encoder profiles with varying stream profile levelbitrate framerate and maximum resolution
12 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
Table of contents
TABLE OF CONTENTS
1 Welcome 311 About the product 312 About this manual 413 Whatrsquos in the box 4
2 Product information 521 Use cases 5211 Media modes 5212 Control modes 7
22 Models 8221 Lite amp Pro 8
23 Features 8231 Resources 9232 EDID 9233 Network 11234 Streaming 11235 Video 12236 Audio 15237 USB HID 15
3 Installation 1731 Front view 1732 Rear view 1933 Start up 20
4 Operation 2141 Introduction 2142 Web interface 21421 Introduction 21422 Browser support 21423 WebUI overview 21424 Login 22
43 Discovery 23431 Introduction 23432 Barco Device Discovery Tool 24433 Discovery via OSD 24434 Web Interface Discovery 25435 Identification button 26
44 Device info 26441 Introduction 26442 Info 27443 Diagnostics 28444 Administration 29445 Software upgrade 31446 Help 31
45 Settings 32451 Introduction 32452 Network settings 324521 IP settings 334522 Managed mode 344523 Unmanaged mode 354524 SNMP settings 35
453 Encoder settings 354531 Overview 354532 Audio 354533 DVI InDP InHDMI In 364534 HDMI Audio In 37
K5903129 NGS-D320 29092016 1
Table of contents
4535 USB Host 37454 Decoder settings 384541 Overview 384542 Audio 384543 DVI OutDP OutHDMI Out 384544 HDMI Audio Out 394545 USB Peripherals 40
5 Cleaning your device 4151 Cleaning procedure 41
6 Repackaging instructions 4361 Device repacking 43
7 Service activities 4571 Reaching the local Barco helpdesk and online support 4572 Online product support 4673 Reporting an issue in SalesForcecom 46
8 Important information 4981 Safety information 4982 Environmental information 5083 Regulatory compliance information 5284 EMC notice 5385 Explanation of symbols 5386 Legal disclaimer 5587 Technical Specifications NGS-D320 Lite 5588 Technical Specifications NGS-D320 Pro 5789 Open source license information 58
2 K5903129 NGS-D320 29092016
1 Welcome
1 WELCOME
11 About the productDevice typeThank you for choosing this Barco device the Network Graphics Source (NGS)
The NGS-D320 is a versatile and powerful networked H264 encoder and decoder Its elegant designsmall form factor and silent operation allows the device to be used in any situation both in office environ-ments and in 247 mission critical applications Due to its versatility the NGS-D320 can be configured atruntime as an encoder or a decoder for DVI HDMI and DisplayPort content with or without audio Thecombination of these functions with integrated keyboard and mouse control in a single unit is ideal tocreate a seamless environment for application sharing simulation and training
Key features
bull Superb Visual ExperienceThe NGS-D320 comes with Barcorsquos latest image processing engine which provides the best scalingand color space conversion algorithms on the market today When distributing graphics the encoderpreserves even the smallest details making it suitable to encode images like spreadsheets or singlepixel line diagrams
bull Simple IntegrationBy default the device will automatically start streaming whenever a valid input signal is connectedThe stream is automatically set up using the most optimal settings based on input resolution andbandwidth In addition the discovery page of the web interface gives an overview of all availabledevices in the network making system configuration easy
bull No Adjustment NeededWith automatic EDIDmanagement and scaling at the decoding side the best experience in distributinggraphics and video over IP is guaranteed Fiddling with displays to get a good picture is thus unnec-essary Switching from one source to another is fluent and does not require the display to re-syncto the new signal The decoder can also both upscale and downscale to match the preferred displaysettings
bull Performance- NGS-D320 Lite The NGS-D320 Lite used as an encoder comes with a dual link DVI a HDMI anda DisplayPort 11a input All inputs support resolutions up to 4096x2160(DCI) and feature activepass-through connectivity Although encoding in full frame rate by default the device also supportslower frame rates This allows you to define the balance between quality and required bandwidthThe encoder latency is below 40ms allowing an end to end latency of below 100ms (note latencydepends on the selected profile)
- NGS-D320 ProThe NGS-D320 Pro has two independent channels which can each be configured individually asencoder or decoder As encoder it exposes maximum two inputs selectable out of a dual link DVIan HDMI 14a and a DisplayPort 11a input All inputs support resolutions up to 4096x2160 (DCI)and feature active pass-through connectivity Although encoding in full frame rate by default thedevice also supports lower frame rates This allows you to define the balance between quality andrequired bandwidth The encoder latency is below 40ms allowing an end to end latency of below100ms (note latency depends on the selected profile)
CAUTION Read all the safety information (Safety information page 49) before oper-ating your NGS-D320
K5903129 NGS-D320 29092016 3
1 Welcome
12 About this manualUser GuideThis User Guide describes how to install and use the Barco device NGS-D320
13 Whatrsquos in the boxNGS-D320 box contentYour Barco NGS-D320 comes withbull Quick Start Guidebull mains cable (EU)bull mains cable (US)bull external power supply (12V60W)
Keep your original packaging It is designed for this device and is the ideal protectionduring transport
4 K5903129 NGS-D320 29092016
2 Product information
2 PRODUCT INFORMATION
21 Use cases
An NGS-D320 device enables hardware-accelerated KVMA-over-IP using standard 1GIPv4 networks It is connected to the network for transporting Audio Video and control
211 Media modes
Different media modesThe device can stream media in 3 different media modes to support various use cases
These 3 media modes are supported
bull Encoderbull Decoderbull Local
A brief description for each media mode is given below
EncoderThe device is typically connected to a desktop PC or server
The corresponding decoder can be
bull Another NGS-D320 devicebull A software based decoder
Install your NGS-D320 as an encoder
To decode use software decoding on a PCserver (eg VLC Media Player ) andor use another NGS-D320 as a decoder
This is illustrated below
1
2 3
4
5
6
7
8
9
9
9
Image 2-1Encoder installation
1 PC server2 NGS-D320 (encoder)3 Switch4 NGS-D320 (decoder)5 PC (SW decoder)6 Audio signal
K5903129 NGS-D320 29092016 5
2 Product information
7 Video signal8 USB HID9 Data (network)
Audio video and USB connections are made from the PC to the NGS-D320
The video content flows from the PCserver to the NGS-D320 the NGS-D320 encodes the video andthen the video is streamed onto the IP network
The audio content can be bi-directional audio can be sent to or received from the NGS-D320The USB peripheral port of the NGS-D320 connects to an USB host port on the PCserver The NGS-D320 emulates an USB HID device and events are sent from the NGS-D320 to the PCserver
DecoderThe device is typically connected to one or two screens Next to the screens the device can also beconnected to a headsetspeakermicrophone a keyboard and a mouse
The corresponding encoder can be
bull Another NGS-D320 devicebull Another Barco device compatible with the NGS-D320
Refer to the specific Barco Systems with NGS-D320 devices for compatible products
1
2
3 4
5
6 7
8
9
6
6
Image 2-2Decoder installation
1 NGS-D320 (encoder)2 Barco device or PCserver3 Switch4 NGS-D320 (decoder)5 Screen headsetspeakermicrophone keyboard or mouse6 Data (network)7 Audio signal8 Video signal9 USB HID
The video interfaces are connected to the screen(s)The audio interfaces are connected to a headset or speakers and a microphone can be connected to theNGS-D320
The keyboard and mouse connect to the USB host interfaces of the NGS-D320
LocalThis mode is a combination of the encoder amp decoder mode
The device is typically connected locally at a desktop position The device sits between the PCserverand the screens headsetspeakermicrophone keyboard and mouse The video audio amp USB cablesconnect from both ends to the NGS-D320 device
These inputs are locally looped through the device
The NGS-D320 device plugs into the network and is capable of streaming amp receiving network traffic si-multaneously
Install your NGS-D320 as illustrated below
6 K5903129 NGS-D320 29092016
2 Product information
1
2
3
4
6 7 8
5
6 7 8
Image 2-3Encoder and decoder installation
1 Screen headsetspeakermicrophone keyboard or mouse2 NGS-D320 (local)3 Barco device or PCserver4 Switch5 Data (network)6 Audio signal7 Video signal8 USB HID
Keyboard local settings To make sure all keys are operable the physical keyboardlayout at decoder side should match the keyboard configuration at encoder side (onPCserver)
212 Control modes
Different control modesThe device can be controlled in 2 modes
bull Locally or Unmanaged modebull Centrally or Managed mode
Unmanaged modeIn this mode the device is used stand-alone
Each device is controlled amp operated locally through its onboard web user interface
See Operation page 21 for details on how to configure amp operate the device
Managed modeIn this mode the device is used in a system
Each device is controlled amp operated centrally via a system controller which communicates with the devicethrough the device API
See the User Manual of the respective system on how to configure amp operate the device within the systemcontext
K5903129 NGS-D320 29092016 7
2 Product information
22 Models
221 Lite amp Pro
DifferencesThe NGS-D320 comes in 2 flavours a Lite and a Pro versionThemain difference between the 2models is the number of simultaneous video streams and display headsthat they support
Refer to Technical Specifications NGS-D320 Lite page 55 and Technical Specifications NGS-D320Pro page 57 for more details of the specifications
Model Lite ProNumberof H264streams
1 up to 2H264 streams
Use cases Encoder orDecoder
Local (EncoderDecoder) or
Dual channel encoder or
Dual channel decoderNumber ofsource inputs
1 up to 2Display heads1
Numberof displayoutputs
1 up to 2
Local use case NA Can be set up to encode 1 H264 stream ANDdecode 1 H264 stream from independentsources simultaneously
Level 51 NA Can only encode OR decode 1 L51 stream(up to 4K resolution) not 2
Maximum resolution 2560x1600 30fps
4096x2160 15fps
2 streams 2560x1600 30fps
1 stream 2560x1600 60fps
1 stream 4096x2160 30fps
Dual quality NA Can encode a single source (less than L51)twice in 2 different qualities
Dual channel NA Can encode both a DVI and a DisplayPortinput simultaneously
Priority principle If an input stream has L51 (4K) only one encoding shall be active
23 FeaturesOverviewThe device supports audio video amp USB media types on the network
In this section an explanation is given on the various features per media type as well as on the networkspecific features
Refer to Operation page 21 on how to configure the NGS-D320 for these features
1 Only one 4K H264 stream can be encoded or decoded at a time
8 K5903129 NGS-D320 29092016
2 Product information
231 Resources
Device behaviourDepending on the model an NGS-D320 has limited audio amp video encoding and decoding resources
A resource utilization algorithm is present on the NGS-D320 that ensures that the device will alwaysbehave in the same way when it is configured in the same way
Priority principleResources are not granted on a ldquofirst come first serverdquo principle but on a priority principle
The following priority principle is valid
bull Encoding always gets priority over decodingbull Encoding will be in order of priority DVI HDMI DPbull If an input stream is configured to use an L51 profile (eg for 4K) only encoding shall be activebull For Pro devices the first stream of an input type will have priority over second stream of the same
input type
These principles apply dynamically and in real-time depending on the actual device status These princi-ples are valid both for audio amp video
Some examples on the priority principle
bull A device is configured to encode 2 inputs (eg 1 DP and 1 DVI) and also configured to decode 1output (eg 1 DVI or 1 DP)When the 2 inputs are active (active syncs detected) the device will only encode decoding will bedisabledIf one of the 2 inputs drops (no active sync detected) the decoding will start automatically
bull A device is configured to encode 1 DP input and 1 DVI inputIf the DP input is 4K resolution (L51) then only the DP input encoding will be activeIf the DP input resolution changes to 1920x1080 then the DVI input encoding will automatically acti-vate
bull A Pro device is configured to encode 1 DP input in 2 qualities and 1 DVI inputThe DVI will be encodedOnly the first configured DP stream will be encoded
ReportingThe actual status of resource utilization is reported continuously via Diagnostics
232 EDID
EDID supportThe NGS-D320 supports EDID at both the input and ouput The EDID can be setup for each input andoutput individually and independently
InputThe EDID at the input is the EDID as seen by the PC This is typically setup at the encoder side Referto Encoder settings page 35 on how to configure
At the input 2 settings are supported
K5903129 NGS-D320 29092016 9
2 Product information
1 Default4 timings will be supported on the source PC with 1920x1200p60 as preferred timing
1920x1200p60
1920x1080p60
2560x1600p603840x2160p30
2 SpecificIn this setting only one specific timing will be providedThe specific timing can be selected out of a list of 46 timings
640x480p50 1176x664p50 1280x960p50 1440x900p50 1920x1080p50 2560x1440p50
640x480p60 1176x664p60 1280x960p60 1440x900p60 1920x1080p60 2560x1440p60
800x600p50 1280x720p50 1280x1024p50 1600x1024p50 1920x1200p50 2560x1600p50800x600p60 1280x720p60 1280x1024p60 1600x1024p60 1920x1200p60 2560x1600p601024x768p50 1280x768p50 1344x1008p50 1600x1200p50 1920x1440p50 3840x2160p251024x768p60 1280x768p60 1344x1008p60 1600x1200p60 1920x1440p60 3840x2160p301152x864p50 1280x800p50 1360x768p50 1680x1050p50 2048x1536p50 4096x2160p251152x864p60 1280x800p60 1360x768p60 1680x1050p60 2048x1536p60 4096x2160p30
The connected source device is free to ignore the EDID of the NGS-D320 When anothertiming is received the NGS-D320 will adapt to this timing as long as it is one of the 48supported timings
Output timingBy default the timing on the output video connector will be set to the first (preferred) detailed timing inthe EDID of the display The timing can also be set to a specific timing ignoring the EDID of the display
This is typically setup at the decoder side The decoded video will be resized and frame rate convertedto be shown full screen on the connected display When resizing aspect ratio will be kept
Refer to Decoder settings page 38on how to configure
At the output 3 modes are supported1 Preferred timing
In this setting the output timing of the device will be the first detailed timing descriptor in the EDID ofthe attached display
2 StandbyIn this setting the output syncs are disabled to make the connected display go to standby
3 SpecificIn this setting the NGS-D320 will not read the EDID from the connected display but will force theoutput as selected out of the 45 supported timings
Loop throughIt is possible to loop through the video amp audio from input to output connector
The loop through behavior is depending on the decoder settingsIf decoding is active no loop through shall be available
If decoding is not active (eg on an encoder) then the output will be a loop through of the input
The loop through will be active
10 K5903129 NGS-D320 29092016
2 Product information
bull 05 seconds after the input is connectedbull 2 seconds after the decoding is disabled
233 Network
DiscoveryNGS-D320 devices can be discovered on the network using the mDNS protocol
Refer to Discovery page 23 on how to discover an NGS-D320
IP addressingThe NGS-D320 supports IPv4 addressing
The IP address can be dynamically configured using DHCP or can be configured to static
If no DHCP is present and no static config is available the device will fall back to linklocal addressing
The NGS-D320 can connect to an NTP (Network Time Protocol) server
All media traffic will be timestamped according to this reference time
If no NTP server is present the media will be timestamped in line with the device clock (starting at 1 Jan1970) The device clock is reset after every reboot
The NGS-D320 can connect to a DNS (Domain Name Service) server
Refer to Network settings page 32 on how to configure NGS-D320 network settings
PortsThe table below lists the ports used for the various protocols on the NGS-D320
Port ProtocolTCP 443 https for web interface and APITCP 554 RTSPTCP 5901 VNC for keyboard amp mouse forwarding from decoder to encoderUDP 5004 RTP audio amp video streaming (5004 is the default port changeable by user)UDP 9875 Session announcements (SAP) on multicast address 2242127254
These ports need to be open on the network infrastructure to ensure proper operation
234 Streaming
Stream controlThe NGS-D320 supports 2 methods to control stream flow1 RTSP
The NGS-D320 supports RTSP (Real Time Streaming Protocol) and runs an RTSP server to manageconnections Connection to the NGS-D320 streams can be done via RTSP clientsBoth RTSP unicast amp multicast is supported
2 SAPThe NGS-D320 supports SAP (Session Announcement Protocol) and sends out SAP announcementsWhen subscribing to the SAP multicast address 2242127254 the SAP message of an NGS-D320will be available and will allow to connect to an NGS-D320 multicast stream
Media streamThe NGS-D320 uses RTP (Real Time Protocol) to stream media
K5903129 NGS-D320 29092016 11
2 Product information
Each encoded stream can have 2 destination addressesports
Device type Number of H264 streams Destination addressesportsNGS-D320 Lite 1 stream Stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSPNGS-D320 Pro 2 streams
bull from 2 different video inputs orbull the same video input encoded
with different quality
Each stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSP
SDPThe streams are described via SDP (Session Description Protocol) For each stream an SDP will beavailable
Refer to Encoder settings page 35 and Decoder settings page 38 to setup streamingon NGS-D320
235 Video
Video formatThe NGS-D320 encodes and decodes DVI HDMI and DP connections tofrom compressed H264 IPtraffic
The H264 stream is
bull IAW RFC3984 (RTP Payload Format for H264 Video)bull YUV420 format with 8-bit colordepth
Encoder profilesThe NGS-D320 encoder supports a number of H264 encoder profiles with varying stream profile levelbitrate framerate and maximum resolution
12 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
Table of contents
4535 USB Host 37454 Decoder settings 384541 Overview 384542 Audio 384543 DVI OutDP OutHDMI Out 384544 HDMI Audio Out 394545 USB Peripherals 40
5 Cleaning your device 4151 Cleaning procedure 41
6 Repackaging instructions 4361 Device repacking 43
7 Service activities 4571 Reaching the local Barco helpdesk and online support 4572 Online product support 4673 Reporting an issue in SalesForcecom 46
8 Important information 4981 Safety information 4982 Environmental information 5083 Regulatory compliance information 5284 EMC notice 5385 Explanation of symbols 5386 Legal disclaimer 5587 Technical Specifications NGS-D320 Lite 5588 Technical Specifications NGS-D320 Pro 5789 Open source license information 58
2 K5903129 NGS-D320 29092016
1 Welcome
1 WELCOME
11 About the productDevice typeThank you for choosing this Barco device the Network Graphics Source (NGS)
The NGS-D320 is a versatile and powerful networked H264 encoder and decoder Its elegant designsmall form factor and silent operation allows the device to be used in any situation both in office environ-ments and in 247 mission critical applications Due to its versatility the NGS-D320 can be configured atruntime as an encoder or a decoder for DVI HDMI and DisplayPort content with or without audio Thecombination of these functions with integrated keyboard and mouse control in a single unit is ideal tocreate a seamless environment for application sharing simulation and training
Key features
bull Superb Visual ExperienceThe NGS-D320 comes with Barcorsquos latest image processing engine which provides the best scalingand color space conversion algorithms on the market today When distributing graphics the encoderpreserves even the smallest details making it suitable to encode images like spreadsheets or singlepixel line diagrams
bull Simple IntegrationBy default the device will automatically start streaming whenever a valid input signal is connectedThe stream is automatically set up using the most optimal settings based on input resolution andbandwidth In addition the discovery page of the web interface gives an overview of all availabledevices in the network making system configuration easy
bull No Adjustment NeededWith automatic EDIDmanagement and scaling at the decoding side the best experience in distributinggraphics and video over IP is guaranteed Fiddling with displays to get a good picture is thus unnec-essary Switching from one source to another is fluent and does not require the display to re-syncto the new signal The decoder can also both upscale and downscale to match the preferred displaysettings
bull Performance- NGS-D320 Lite The NGS-D320 Lite used as an encoder comes with a dual link DVI a HDMI anda DisplayPort 11a input All inputs support resolutions up to 4096x2160(DCI) and feature activepass-through connectivity Although encoding in full frame rate by default the device also supportslower frame rates This allows you to define the balance between quality and required bandwidthThe encoder latency is below 40ms allowing an end to end latency of below 100ms (note latencydepends on the selected profile)
- NGS-D320 ProThe NGS-D320 Pro has two independent channels which can each be configured individually asencoder or decoder As encoder it exposes maximum two inputs selectable out of a dual link DVIan HDMI 14a and a DisplayPort 11a input All inputs support resolutions up to 4096x2160 (DCI)and feature active pass-through connectivity Although encoding in full frame rate by default thedevice also supports lower frame rates This allows you to define the balance between quality andrequired bandwidth The encoder latency is below 40ms allowing an end to end latency of below100ms (note latency depends on the selected profile)
CAUTION Read all the safety information (Safety information page 49) before oper-ating your NGS-D320
K5903129 NGS-D320 29092016 3
1 Welcome
12 About this manualUser GuideThis User Guide describes how to install and use the Barco device NGS-D320
13 Whatrsquos in the boxNGS-D320 box contentYour Barco NGS-D320 comes withbull Quick Start Guidebull mains cable (EU)bull mains cable (US)bull external power supply (12V60W)
Keep your original packaging It is designed for this device and is the ideal protectionduring transport
4 K5903129 NGS-D320 29092016
2 Product information
2 PRODUCT INFORMATION
21 Use cases
An NGS-D320 device enables hardware-accelerated KVMA-over-IP using standard 1GIPv4 networks It is connected to the network for transporting Audio Video and control
211 Media modes
Different media modesThe device can stream media in 3 different media modes to support various use cases
These 3 media modes are supported
bull Encoderbull Decoderbull Local
A brief description for each media mode is given below
EncoderThe device is typically connected to a desktop PC or server
The corresponding decoder can be
bull Another NGS-D320 devicebull A software based decoder
Install your NGS-D320 as an encoder
To decode use software decoding on a PCserver (eg VLC Media Player ) andor use another NGS-D320 as a decoder
This is illustrated below
1
2 3
4
5
6
7
8
9
9
9
Image 2-1Encoder installation
1 PC server2 NGS-D320 (encoder)3 Switch4 NGS-D320 (decoder)5 PC (SW decoder)6 Audio signal
K5903129 NGS-D320 29092016 5
2 Product information
7 Video signal8 USB HID9 Data (network)
Audio video and USB connections are made from the PC to the NGS-D320
The video content flows from the PCserver to the NGS-D320 the NGS-D320 encodes the video andthen the video is streamed onto the IP network
The audio content can be bi-directional audio can be sent to or received from the NGS-D320The USB peripheral port of the NGS-D320 connects to an USB host port on the PCserver The NGS-D320 emulates an USB HID device and events are sent from the NGS-D320 to the PCserver
DecoderThe device is typically connected to one or two screens Next to the screens the device can also beconnected to a headsetspeakermicrophone a keyboard and a mouse
The corresponding encoder can be
bull Another NGS-D320 devicebull Another Barco device compatible with the NGS-D320
Refer to the specific Barco Systems with NGS-D320 devices for compatible products
1
2
3 4
5
6 7
8
9
6
6
Image 2-2Decoder installation
1 NGS-D320 (encoder)2 Barco device or PCserver3 Switch4 NGS-D320 (decoder)5 Screen headsetspeakermicrophone keyboard or mouse6 Data (network)7 Audio signal8 Video signal9 USB HID
The video interfaces are connected to the screen(s)The audio interfaces are connected to a headset or speakers and a microphone can be connected to theNGS-D320
The keyboard and mouse connect to the USB host interfaces of the NGS-D320
LocalThis mode is a combination of the encoder amp decoder mode
The device is typically connected locally at a desktop position The device sits between the PCserverand the screens headsetspeakermicrophone keyboard and mouse The video audio amp USB cablesconnect from both ends to the NGS-D320 device
These inputs are locally looped through the device
The NGS-D320 device plugs into the network and is capable of streaming amp receiving network traffic si-multaneously
Install your NGS-D320 as illustrated below
6 K5903129 NGS-D320 29092016
2 Product information
1
2
3
4
6 7 8
5
6 7 8
Image 2-3Encoder and decoder installation
1 Screen headsetspeakermicrophone keyboard or mouse2 NGS-D320 (local)3 Barco device or PCserver4 Switch5 Data (network)6 Audio signal7 Video signal8 USB HID
Keyboard local settings To make sure all keys are operable the physical keyboardlayout at decoder side should match the keyboard configuration at encoder side (onPCserver)
212 Control modes
Different control modesThe device can be controlled in 2 modes
bull Locally or Unmanaged modebull Centrally or Managed mode
Unmanaged modeIn this mode the device is used stand-alone
Each device is controlled amp operated locally through its onboard web user interface
See Operation page 21 for details on how to configure amp operate the device
Managed modeIn this mode the device is used in a system
Each device is controlled amp operated centrally via a system controller which communicates with the devicethrough the device API
See the User Manual of the respective system on how to configure amp operate the device within the systemcontext
K5903129 NGS-D320 29092016 7
2 Product information
22 Models
221 Lite amp Pro
DifferencesThe NGS-D320 comes in 2 flavours a Lite and a Pro versionThemain difference between the 2models is the number of simultaneous video streams and display headsthat they support
Refer to Technical Specifications NGS-D320 Lite page 55 and Technical Specifications NGS-D320Pro page 57 for more details of the specifications
Model Lite ProNumberof H264streams
1 up to 2H264 streams
Use cases Encoder orDecoder
Local (EncoderDecoder) or
Dual channel encoder or
Dual channel decoderNumber ofsource inputs
1 up to 2Display heads1
Numberof displayoutputs
1 up to 2
Local use case NA Can be set up to encode 1 H264 stream ANDdecode 1 H264 stream from independentsources simultaneously
Level 51 NA Can only encode OR decode 1 L51 stream(up to 4K resolution) not 2
Maximum resolution 2560x1600 30fps
4096x2160 15fps
2 streams 2560x1600 30fps
1 stream 2560x1600 60fps
1 stream 4096x2160 30fps
Dual quality NA Can encode a single source (less than L51)twice in 2 different qualities
Dual channel NA Can encode both a DVI and a DisplayPortinput simultaneously
Priority principle If an input stream has L51 (4K) only one encoding shall be active
23 FeaturesOverviewThe device supports audio video amp USB media types on the network
In this section an explanation is given on the various features per media type as well as on the networkspecific features
Refer to Operation page 21 on how to configure the NGS-D320 for these features
1 Only one 4K H264 stream can be encoded or decoded at a time
8 K5903129 NGS-D320 29092016
2 Product information
231 Resources
Device behaviourDepending on the model an NGS-D320 has limited audio amp video encoding and decoding resources
A resource utilization algorithm is present on the NGS-D320 that ensures that the device will alwaysbehave in the same way when it is configured in the same way
Priority principleResources are not granted on a ldquofirst come first serverdquo principle but on a priority principle
The following priority principle is valid
bull Encoding always gets priority over decodingbull Encoding will be in order of priority DVI HDMI DPbull If an input stream is configured to use an L51 profile (eg for 4K) only encoding shall be activebull For Pro devices the first stream of an input type will have priority over second stream of the same
input type
These principles apply dynamically and in real-time depending on the actual device status These princi-ples are valid both for audio amp video
Some examples on the priority principle
bull A device is configured to encode 2 inputs (eg 1 DP and 1 DVI) and also configured to decode 1output (eg 1 DVI or 1 DP)When the 2 inputs are active (active syncs detected) the device will only encode decoding will bedisabledIf one of the 2 inputs drops (no active sync detected) the decoding will start automatically
bull A device is configured to encode 1 DP input and 1 DVI inputIf the DP input is 4K resolution (L51) then only the DP input encoding will be activeIf the DP input resolution changes to 1920x1080 then the DVI input encoding will automatically acti-vate
bull A Pro device is configured to encode 1 DP input in 2 qualities and 1 DVI inputThe DVI will be encodedOnly the first configured DP stream will be encoded
ReportingThe actual status of resource utilization is reported continuously via Diagnostics
232 EDID
EDID supportThe NGS-D320 supports EDID at both the input and ouput The EDID can be setup for each input andoutput individually and independently
InputThe EDID at the input is the EDID as seen by the PC This is typically setup at the encoder side Referto Encoder settings page 35 on how to configure
At the input 2 settings are supported
K5903129 NGS-D320 29092016 9
2 Product information
1 Default4 timings will be supported on the source PC with 1920x1200p60 as preferred timing
1920x1200p60
1920x1080p60
2560x1600p603840x2160p30
2 SpecificIn this setting only one specific timing will be providedThe specific timing can be selected out of a list of 46 timings
640x480p50 1176x664p50 1280x960p50 1440x900p50 1920x1080p50 2560x1440p50
640x480p60 1176x664p60 1280x960p60 1440x900p60 1920x1080p60 2560x1440p60
800x600p50 1280x720p50 1280x1024p50 1600x1024p50 1920x1200p50 2560x1600p50800x600p60 1280x720p60 1280x1024p60 1600x1024p60 1920x1200p60 2560x1600p601024x768p50 1280x768p50 1344x1008p50 1600x1200p50 1920x1440p50 3840x2160p251024x768p60 1280x768p60 1344x1008p60 1600x1200p60 1920x1440p60 3840x2160p301152x864p50 1280x800p50 1360x768p50 1680x1050p50 2048x1536p50 4096x2160p251152x864p60 1280x800p60 1360x768p60 1680x1050p60 2048x1536p60 4096x2160p30
The connected source device is free to ignore the EDID of the NGS-D320 When anothertiming is received the NGS-D320 will adapt to this timing as long as it is one of the 48supported timings
Output timingBy default the timing on the output video connector will be set to the first (preferred) detailed timing inthe EDID of the display The timing can also be set to a specific timing ignoring the EDID of the display
This is typically setup at the decoder side The decoded video will be resized and frame rate convertedto be shown full screen on the connected display When resizing aspect ratio will be kept
Refer to Decoder settings page 38on how to configure
At the output 3 modes are supported1 Preferred timing
In this setting the output timing of the device will be the first detailed timing descriptor in the EDID ofthe attached display
2 StandbyIn this setting the output syncs are disabled to make the connected display go to standby
3 SpecificIn this setting the NGS-D320 will not read the EDID from the connected display but will force theoutput as selected out of the 45 supported timings
Loop throughIt is possible to loop through the video amp audio from input to output connector
The loop through behavior is depending on the decoder settingsIf decoding is active no loop through shall be available
If decoding is not active (eg on an encoder) then the output will be a loop through of the input
The loop through will be active
10 K5903129 NGS-D320 29092016
2 Product information
bull 05 seconds after the input is connectedbull 2 seconds after the decoding is disabled
233 Network
DiscoveryNGS-D320 devices can be discovered on the network using the mDNS protocol
Refer to Discovery page 23 on how to discover an NGS-D320
IP addressingThe NGS-D320 supports IPv4 addressing
The IP address can be dynamically configured using DHCP or can be configured to static
If no DHCP is present and no static config is available the device will fall back to linklocal addressing
The NGS-D320 can connect to an NTP (Network Time Protocol) server
All media traffic will be timestamped according to this reference time
If no NTP server is present the media will be timestamped in line with the device clock (starting at 1 Jan1970) The device clock is reset after every reboot
The NGS-D320 can connect to a DNS (Domain Name Service) server
Refer to Network settings page 32 on how to configure NGS-D320 network settings
PortsThe table below lists the ports used for the various protocols on the NGS-D320
Port ProtocolTCP 443 https for web interface and APITCP 554 RTSPTCP 5901 VNC for keyboard amp mouse forwarding from decoder to encoderUDP 5004 RTP audio amp video streaming (5004 is the default port changeable by user)UDP 9875 Session announcements (SAP) on multicast address 2242127254
These ports need to be open on the network infrastructure to ensure proper operation
234 Streaming
Stream controlThe NGS-D320 supports 2 methods to control stream flow1 RTSP
The NGS-D320 supports RTSP (Real Time Streaming Protocol) and runs an RTSP server to manageconnections Connection to the NGS-D320 streams can be done via RTSP clientsBoth RTSP unicast amp multicast is supported
2 SAPThe NGS-D320 supports SAP (Session Announcement Protocol) and sends out SAP announcementsWhen subscribing to the SAP multicast address 2242127254 the SAP message of an NGS-D320will be available and will allow to connect to an NGS-D320 multicast stream
Media streamThe NGS-D320 uses RTP (Real Time Protocol) to stream media
K5903129 NGS-D320 29092016 11
2 Product information
Each encoded stream can have 2 destination addressesports
Device type Number of H264 streams Destination addressesportsNGS-D320 Lite 1 stream Stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSPNGS-D320 Pro 2 streams
bull from 2 different video inputs orbull the same video input encoded
with different quality
Each stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSP
SDPThe streams are described via SDP (Session Description Protocol) For each stream an SDP will beavailable
Refer to Encoder settings page 35 and Decoder settings page 38 to setup streamingon NGS-D320
235 Video
Video formatThe NGS-D320 encodes and decodes DVI HDMI and DP connections tofrom compressed H264 IPtraffic
The H264 stream is
bull IAW RFC3984 (RTP Payload Format for H264 Video)bull YUV420 format with 8-bit colordepth
Encoder profilesThe NGS-D320 encoder supports a number of H264 encoder profiles with varying stream profile levelbitrate framerate and maximum resolution
12 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
1 Welcome
1 WELCOME
11 About the productDevice typeThank you for choosing this Barco device the Network Graphics Source (NGS)
The NGS-D320 is a versatile and powerful networked H264 encoder and decoder Its elegant designsmall form factor and silent operation allows the device to be used in any situation both in office environ-ments and in 247 mission critical applications Due to its versatility the NGS-D320 can be configured atruntime as an encoder or a decoder for DVI HDMI and DisplayPort content with or without audio Thecombination of these functions with integrated keyboard and mouse control in a single unit is ideal tocreate a seamless environment for application sharing simulation and training
Key features
bull Superb Visual ExperienceThe NGS-D320 comes with Barcorsquos latest image processing engine which provides the best scalingand color space conversion algorithms on the market today When distributing graphics the encoderpreserves even the smallest details making it suitable to encode images like spreadsheets or singlepixel line diagrams
bull Simple IntegrationBy default the device will automatically start streaming whenever a valid input signal is connectedThe stream is automatically set up using the most optimal settings based on input resolution andbandwidth In addition the discovery page of the web interface gives an overview of all availabledevices in the network making system configuration easy
bull No Adjustment NeededWith automatic EDIDmanagement and scaling at the decoding side the best experience in distributinggraphics and video over IP is guaranteed Fiddling with displays to get a good picture is thus unnec-essary Switching from one source to another is fluent and does not require the display to re-syncto the new signal The decoder can also both upscale and downscale to match the preferred displaysettings
bull Performance- NGS-D320 Lite The NGS-D320 Lite used as an encoder comes with a dual link DVI a HDMI anda DisplayPort 11a input All inputs support resolutions up to 4096x2160(DCI) and feature activepass-through connectivity Although encoding in full frame rate by default the device also supportslower frame rates This allows you to define the balance between quality and required bandwidthThe encoder latency is below 40ms allowing an end to end latency of below 100ms (note latencydepends on the selected profile)
- NGS-D320 ProThe NGS-D320 Pro has two independent channels which can each be configured individually asencoder or decoder As encoder it exposes maximum two inputs selectable out of a dual link DVIan HDMI 14a and a DisplayPort 11a input All inputs support resolutions up to 4096x2160 (DCI)and feature active pass-through connectivity Although encoding in full frame rate by default thedevice also supports lower frame rates This allows you to define the balance between quality andrequired bandwidth The encoder latency is below 40ms allowing an end to end latency of below100ms (note latency depends on the selected profile)
CAUTION Read all the safety information (Safety information page 49) before oper-ating your NGS-D320
K5903129 NGS-D320 29092016 3
1 Welcome
12 About this manualUser GuideThis User Guide describes how to install and use the Barco device NGS-D320
13 Whatrsquos in the boxNGS-D320 box contentYour Barco NGS-D320 comes withbull Quick Start Guidebull mains cable (EU)bull mains cable (US)bull external power supply (12V60W)
Keep your original packaging It is designed for this device and is the ideal protectionduring transport
4 K5903129 NGS-D320 29092016
2 Product information
2 PRODUCT INFORMATION
21 Use cases
An NGS-D320 device enables hardware-accelerated KVMA-over-IP using standard 1GIPv4 networks It is connected to the network for transporting Audio Video and control
211 Media modes
Different media modesThe device can stream media in 3 different media modes to support various use cases
These 3 media modes are supported
bull Encoderbull Decoderbull Local
A brief description for each media mode is given below
EncoderThe device is typically connected to a desktop PC or server
The corresponding decoder can be
bull Another NGS-D320 devicebull A software based decoder
Install your NGS-D320 as an encoder
To decode use software decoding on a PCserver (eg VLC Media Player ) andor use another NGS-D320 as a decoder
This is illustrated below
1
2 3
4
5
6
7
8
9
9
9
Image 2-1Encoder installation
1 PC server2 NGS-D320 (encoder)3 Switch4 NGS-D320 (decoder)5 PC (SW decoder)6 Audio signal
K5903129 NGS-D320 29092016 5
2 Product information
7 Video signal8 USB HID9 Data (network)
Audio video and USB connections are made from the PC to the NGS-D320
The video content flows from the PCserver to the NGS-D320 the NGS-D320 encodes the video andthen the video is streamed onto the IP network
The audio content can be bi-directional audio can be sent to or received from the NGS-D320The USB peripheral port of the NGS-D320 connects to an USB host port on the PCserver The NGS-D320 emulates an USB HID device and events are sent from the NGS-D320 to the PCserver
DecoderThe device is typically connected to one or two screens Next to the screens the device can also beconnected to a headsetspeakermicrophone a keyboard and a mouse
The corresponding encoder can be
bull Another NGS-D320 devicebull Another Barco device compatible with the NGS-D320
Refer to the specific Barco Systems with NGS-D320 devices for compatible products
1
2
3 4
5
6 7
8
9
6
6
Image 2-2Decoder installation
1 NGS-D320 (encoder)2 Barco device or PCserver3 Switch4 NGS-D320 (decoder)5 Screen headsetspeakermicrophone keyboard or mouse6 Data (network)7 Audio signal8 Video signal9 USB HID
The video interfaces are connected to the screen(s)The audio interfaces are connected to a headset or speakers and a microphone can be connected to theNGS-D320
The keyboard and mouse connect to the USB host interfaces of the NGS-D320
LocalThis mode is a combination of the encoder amp decoder mode
The device is typically connected locally at a desktop position The device sits between the PCserverand the screens headsetspeakermicrophone keyboard and mouse The video audio amp USB cablesconnect from both ends to the NGS-D320 device
These inputs are locally looped through the device
The NGS-D320 device plugs into the network and is capable of streaming amp receiving network traffic si-multaneously
Install your NGS-D320 as illustrated below
6 K5903129 NGS-D320 29092016
2 Product information
1
2
3
4
6 7 8
5
6 7 8
Image 2-3Encoder and decoder installation
1 Screen headsetspeakermicrophone keyboard or mouse2 NGS-D320 (local)3 Barco device or PCserver4 Switch5 Data (network)6 Audio signal7 Video signal8 USB HID
Keyboard local settings To make sure all keys are operable the physical keyboardlayout at decoder side should match the keyboard configuration at encoder side (onPCserver)
212 Control modes
Different control modesThe device can be controlled in 2 modes
bull Locally or Unmanaged modebull Centrally or Managed mode
Unmanaged modeIn this mode the device is used stand-alone
Each device is controlled amp operated locally through its onboard web user interface
See Operation page 21 for details on how to configure amp operate the device
Managed modeIn this mode the device is used in a system
Each device is controlled amp operated centrally via a system controller which communicates with the devicethrough the device API
See the User Manual of the respective system on how to configure amp operate the device within the systemcontext
K5903129 NGS-D320 29092016 7
2 Product information
22 Models
221 Lite amp Pro
DifferencesThe NGS-D320 comes in 2 flavours a Lite and a Pro versionThemain difference between the 2models is the number of simultaneous video streams and display headsthat they support
Refer to Technical Specifications NGS-D320 Lite page 55 and Technical Specifications NGS-D320Pro page 57 for more details of the specifications
Model Lite ProNumberof H264streams
1 up to 2H264 streams
Use cases Encoder orDecoder
Local (EncoderDecoder) or
Dual channel encoder or
Dual channel decoderNumber ofsource inputs
1 up to 2Display heads1
Numberof displayoutputs
1 up to 2
Local use case NA Can be set up to encode 1 H264 stream ANDdecode 1 H264 stream from independentsources simultaneously
Level 51 NA Can only encode OR decode 1 L51 stream(up to 4K resolution) not 2
Maximum resolution 2560x1600 30fps
4096x2160 15fps
2 streams 2560x1600 30fps
1 stream 2560x1600 60fps
1 stream 4096x2160 30fps
Dual quality NA Can encode a single source (less than L51)twice in 2 different qualities
Dual channel NA Can encode both a DVI and a DisplayPortinput simultaneously
Priority principle If an input stream has L51 (4K) only one encoding shall be active
23 FeaturesOverviewThe device supports audio video amp USB media types on the network
In this section an explanation is given on the various features per media type as well as on the networkspecific features
Refer to Operation page 21 on how to configure the NGS-D320 for these features
1 Only one 4K H264 stream can be encoded or decoded at a time
8 K5903129 NGS-D320 29092016
2 Product information
231 Resources
Device behaviourDepending on the model an NGS-D320 has limited audio amp video encoding and decoding resources
A resource utilization algorithm is present on the NGS-D320 that ensures that the device will alwaysbehave in the same way when it is configured in the same way
Priority principleResources are not granted on a ldquofirst come first serverdquo principle but on a priority principle
The following priority principle is valid
bull Encoding always gets priority over decodingbull Encoding will be in order of priority DVI HDMI DPbull If an input stream is configured to use an L51 profile (eg for 4K) only encoding shall be activebull For Pro devices the first stream of an input type will have priority over second stream of the same
input type
These principles apply dynamically and in real-time depending on the actual device status These princi-ples are valid both for audio amp video
Some examples on the priority principle
bull A device is configured to encode 2 inputs (eg 1 DP and 1 DVI) and also configured to decode 1output (eg 1 DVI or 1 DP)When the 2 inputs are active (active syncs detected) the device will only encode decoding will bedisabledIf one of the 2 inputs drops (no active sync detected) the decoding will start automatically
bull A device is configured to encode 1 DP input and 1 DVI inputIf the DP input is 4K resolution (L51) then only the DP input encoding will be activeIf the DP input resolution changes to 1920x1080 then the DVI input encoding will automatically acti-vate
bull A Pro device is configured to encode 1 DP input in 2 qualities and 1 DVI inputThe DVI will be encodedOnly the first configured DP stream will be encoded
ReportingThe actual status of resource utilization is reported continuously via Diagnostics
232 EDID
EDID supportThe NGS-D320 supports EDID at both the input and ouput The EDID can be setup for each input andoutput individually and independently
InputThe EDID at the input is the EDID as seen by the PC This is typically setup at the encoder side Referto Encoder settings page 35 on how to configure
At the input 2 settings are supported
K5903129 NGS-D320 29092016 9
2 Product information
1 Default4 timings will be supported on the source PC with 1920x1200p60 as preferred timing
1920x1200p60
1920x1080p60
2560x1600p603840x2160p30
2 SpecificIn this setting only one specific timing will be providedThe specific timing can be selected out of a list of 46 timings
640x480p50 1176x664p50 1280x960p50 1440x900p50 1920x1080p50 2560x1440p50
640x480p60 1176x664p60 1280x960p60 1440x900p60 1920x1080p60 2560x1440p60
800x600p50 1280x720p50 1280x1024p50 1600x1024p50 1920x1200p50 2560x1600p50800x600p60 1280x720p60 1280x1024p60 1600x1024p60 1920x1200p60 2560x1600p601024x768p50 1280x768p50 1344x1008p50 1600x1200p50 1920x1440p50 3840x2160p251024x768p60 1280x768p60 1344x1008p60 1600x1200p60 1920x1440p60 3840x2160p301152x864p50 1280x800p50 1360x768p50 1680x1050p50 2048x1536p50 4096x2160p251152x864p60 1280x800p60 1360x768p60 1680x1050p60 2048x1536p60 4096x2160p30
The connected source device is free to ignore the EDID of the NGS-D320 When anothertiming is received the NGS-D320 will adapt to this timing as long as it is one of the 48supported timings
Output timingBy default the timing on the output video connector will be set to the first (preferred) detailed timing inthe EDID of the display The timing can also be set to a specific timing ignoring the EDID of the display
This is typically setup at the decoder side The decoded video will be resized and frame rate convertedto be shown full screen on the connected display When resizing aspect ratio will be kept
Refer to Decoder settings page 38on how to configure
At the output 3 modes are supported1 Preferred timing
In this setting the output timing of the device will be the first detailed timing descriptor in the EDID ofthe attached display
2 StandbyIn this setting the output syncs are disabled to make the connected display go to standby
3 SpecificIn this setting the NGS-D320 will not read the EDID from the connected display but will force theoutput as selected out of the 45 supported timings
Loop throughIt is possible to loop through the video amp audio from input to output connector
The loop through behavior is depending on the decoder settingsIf decoding is active no loop through shall be available
If decoding is not active (eg on an encoder) then the output will be a loop through of the input
The loop through will be active
10 K5903129 NGS-D320 29092016
2 Product information
bull 05 seconds after the input is connectedbull 2 seconds after the decoding is disabled
233 Network
DiscoveryNGS-D320 devices can be discovered on the network using the mDNS protocol
Refer to Discovery page 23 on how to discover an NGS-D320
IP addressingThe NGS-D320 supports IPv4 addressing
The IP address can be dynamically configured using DHCP or can be configured to static
If no DHCP is present and no static config is available the device will fall back to linklocal addressing
The NGS-D320 can connect to an NTP (Network Time Protocol) server
All media traffic will be timestamped according to this reference time
If no NTP server is present the media will be timestamped in line with the device clock (starting at 1 Jan1970) The device clock is reset after every reboot
The NGS-D320 can connect to a DNS (Domain Name Service) server
Refer to Network settings page 32 on how to configure NGS-D320 network settings
PortsThe table below lists the ports used for the various protocols on the NGS-D320
Port ProtocolTCP 443 https for web interface and APITCP 554 RTSPTCP 5901 VNC for keyboard amp mouse forwarding from decoder to encoderUDP 5004 RTP audio amp video streaming (5004 is the default port changeable by user)UDP 9875 Session announcements (SAP) on multicast address 2242127254
These ports need to be open on the network infrastructure to ensure proper operation
234 Streaming
Stream controlThe NGS-D320 supports 2 methods to control stream flow1 RTSP
The NGS-D320 supports RTSP (Real Time Streaming Protocol) and runs an RTSP server to manageconnections Connection to the NGS-D320 streams can be done via RTSP clientsBoth RTSP unicast amp multicast is supported
2 SAPThe NGS-D320 supports SAP (Session Announcement Protocol) and sends out SAP announcementsWhen subscribing to the SAP multicast address 2242127254 the SAP message of an NGS-D320will be available and will allow to connect to an NGS-D320 multicast stream
Media streamThe NGS-D320 uses RTP (Real Time Protocol) to stream media
K5903129 NGS-D320 29092016 11
2 Product information
Each encoded stream can have 2 destination addressesports
Device type Number of H264 streams Destination addressesportsNGS-D320 Lite 1 stream Stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSPNGS-D320 Pro 2 streams
bull from 2 different video inputs orbull the same video input encoded
with different quality
Each stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSP
SDPThe streams are described via SDP (Session Description Protocol) For each stream an SDP will beavailable
Refer to Encoder settings page 35 and Decoder settings page 38 to setup streamingon NGS-D320
235 Video
Video formatThe NGS-D320 encodes and decodes DVI HDMI and DP connections tofrom compressed H264 IPtraffic
The H264 stream is
bull IAW RFC3984 (RTP Payload Format for H264 Video)bull YUV420 format with 8-bit colordepth
Encoder profilesThe NGS-D320 encoder supports a number of H264 encoder profiles with varying stream profile levelbitrate framerate and maximum resolution
12 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
1 Welcome
12 About this manualUser GuideThis User Guide describes how to install and use the Barco device NGS-D320
13 Whatrsquos in the boxNGS-D320 box contentYour Barco NGS-D320 comes withbull Quick Start Guidebull mains cable (EU)bull mains cable (US)bull external power supply (12V60W)
Keep your original packaging It is designed for this device and is the ideal protectionduring transport
4 K5903129 NGS-D320 29092016
2 Product information
2 PRODUCT INFORMATION
21 Use cases
An NGS-D320 device enables hardware-accelerated KVMA-over-IP using standard 1GIPv4 networks It is connected to the network for transporting Audio Video and control
211 Media modes
Different media modesThe device can stream media in 3 different media modes to support various use cases
These 3 media modes are supported
bull Encoderbull Decoderbull Local
A brief description for each media mode is given below
EncoderThe device is typically connected to a desktop PC or server
The corresponding decoder can be
bull Another NGS-D320 devicebull A software based decoder
Install your NGS-D320 as an encoder
To decode use software decoding on a PCserver (eg VLC Media Player ) andor use another NGS-D320 as a decoder
This is illustrated below
1
2 3
4
5
6
7
8
9
9
9
Image 2-1Encoder installation
1 PC server2 NGS-D320 (encoder)3 Switch4 NGS-D320 (decoder)5 PC (SW decoder)6 Audio signal
K5903129 NGS-D320 29092016 5
2 Product information
7 Video signal8 USB HID9 Data (network)
Audio video and USB connections are made from the PC to the NGS-D320
The video content flows from the PCserver to the NGS-D320 the NGS-D320 encodes the video andthen the video is streamed onto the IP network
The audio content can be bi-directional audio can be sent to or received from the NGS-D320The USB peripheral port of the NGS-D320 connects to an USB host port on the PCserver The NGS-D320 emulates an USB HID device and events are sent from the NGS-D320 to the PCserver
DecoderThe device is typically connected to one or two screens Next to the screens the device can also beconnected to a headsetspeakermicrophone a keyboard and a mouse
The corresponding encoder can be
bull Another NGS-D320 devicebull Another Barco device compatible with the NGS-D320
Refer to the specific Barco Systems with NGS-D320 devices for compatible products
1
2
3 4
5
6 7
8
9
6
6
Image 2-2Decoder installation
1 NGS-D320 (encoder)2 Barco device or PCserver3 Switch4 NGS-D320 (decoder)5 Screen headsetspeakermicrophone keyboard or mouse6 Data (network)7 Audio signal8 Video signal9 USB HID
The video interfaces are connected to the screen(s)The audio interfaces are connected to a headset or speakers and a microphone can be connected to theNGS-D320
The keyboard and mouse connect to the USB host interfaces of the NGS-D320
LocalThis mode is a combination of the encoder amp decoder mode
The device is typically connected locally at a desktop position The device sits between the PCserverand the screens headsetspeakermicrophone keyboard and mouse The video audio amp USB cablesconnect from both ends to the NGS-D320 device
These inputs are locally looped through the device
The NGS-D320 device plugs into the network and is capable of streaming amp receiving network traffic si-multaneously
Install your NGS-D320 as illustrated below
6 K5903129 NGS-D320 29092016
2 Product information
1
2
3
4
6 7 8
5
6 7 8
Image 2-3Encoder and decoder installation
1 Screen headsetspeakermicrophone keyboard or mouse2 NGS-D320 (local)3 Barco device or PCserver4 Switch5 Data (network)6 Audio signal7 Video signal8 USB HID
Keyboard local settings To make sure all keys are operable the physical keyboardlayout at decoder side should match the keyboard configuration at encoder side (onPCserver)
212 Control modes
Different control modesThe device can be controlled in 2 modes
bull Locally or Unmanaged modebull Centrally or Managed mode
Unmanaged modeIn this mode the device is used stand-alone
Each device is controlled amp operated locally through its onboard web user interface
See Operation page 21 for details on how to configure amp operate the device
Managed modeIn this mode the device is used in a system
Each device is controlled amp operated centrally via a system controller which communicates with the devicethrough the device API
See the User Manual of the respective system on how to configure amp operate the device within the systemcontext
K5903129 NGS-D320 29092016 7
2 Product information
22 Models
221 Lite amp Pro
DifferencesThe NGS-D320 comes in 2 flavours a Lite and a Pro versionThemain difference between the 2models is the number of simultaneous video streams and display headsthat they support
Refer to Technical Specifications NGS-D320 Lite page 55 and Technical Specifications NGS-D320Pro page 57 for more details of the specifications
Model Lite ProNumberof H264streams
1 up to 2H264 streams
Use cases Encoder orDecoder
Local (EncoderDecoder) or
Dual channel encoder or
Dual channel decoderNumber ofsource inputs
1 up to 2Display heads1
Numberof displayoutputs
1 up to 2
Local use case NA Can be set up to encode 1 H264 stream ANDdecode 1 H264 stream from independentsources simultaneously
Level 51 NA Can only encode OR decode 1 L51 stream(up to 4K resolution) not 2
Maximum resolution 2560x1600 30fps
4096x2160 15fps
2 streams 2560x1600 30fps
1 stream 2560x1600 60fps
1 stream 4096x2160 30fps
Dual quality NA Can encode a single source (less than L51)twice in 2 different qualities
Dual channel NA Can encode both a DVI and a DisplayPortinput simultaneously
Priority principle If an input stream has L51 (4K) only one encoding shall be active
23 FeaturesOverviewThe device supports audio video amp USB media types on the network
In this section an explanation is given on the various features per media type as well as on the networkspecific features
Refer to Operation page 21 on how to configure the NGS-D320 for these features
1 Only one 4K H264 stream can be encoded or decoded at a time
8 K5903129 NGS-D320 29092016
2 Product information
231 Resources
Device behaviourDepending on the model an NGS-D320 has limited audio amp video encoding and decoding resources
A resource utilization algorithm is present on the NGS-D320 that ensures that the device will alwaysbehave in the same way when it is configured in the same way
Priority principleResources are not granted on a ldquofirst come first serverdquo principle but on a priority principle
The following priority principle is valid
bull Encoding always gets priority over decodingbull Encoding will be in order of priority DVI HDMI DPbull If an input stream is configured to use an L51 profile (eg for 4K) only encoding shall be activebull For Pro devices the first stream of an input type will have priority over second stream of the same
input type
These principles apply dynamically and in real-time depending on the actual device status These princi-ples are valid both for audio amp video
Some examples on the priority principle
bull A device is configured to encode 2 inputs (eg 1 DP and 1 DVI) and also configured to decode 1output (eg 1 DVI or 1 DP)When the 2 inputs are active (active syncs detected) the device will only encode decoding will bedisabledIf one of the 2 inputs drops (no active sync detected) the decoding will start automatically
bull A device is configured to encode 1 DP input and 1 DVI inputIf the DP input is 4K resolution (L51) then only the DP input encoding will be activeIf the DP input resolution changes to 1920x1080 then the DVI input encoding will automatically acti-vate
bull A Pro device is configured to encode 1 DP input in 2 qualities and 1 DVI inputThe DVI will be encodedOnly the first configured DP stream will be encoded
ReportingThe actual status of resource utilization is reported continuously via Diagnostics
232 EDID
EDID supportThe NGS-D320 supports EDID at both the input and ouput The EDID can be setup for each input andoutput individually and independently
InputThe EDID at the input is the EDID as seen by the PC This is typically setup at the encoder side Referto Encoder settings page 35 on how to configure
At the input 2 settings are supported
K5903129 NGS-D320 29092016 9
2 Product information
1 Default4 timings will be supported on the source PC with 1920x1200p60 as preferred timing
1920x1200p60
1920x1080p60
2560x1600p603840x2160p30
2 SpecificIn this setting only one specific timing will be providedThe specific timing can be selected out of a list of 46 timings
640x480p50 1176x664p50 1280x960p50 1440x900p50 1920x1080p50 2560x1440p50
640x480p60 1176x664p60 1280x960p60 1440x900p60 1920x1080p60 2560x1440p60
800x600p50 1280x720p50 1280x1024p50 1600x1024p50 1920x1200p50 2560x1600p50800x600p60 1280x720p60 1280x1024p60 1600x1024p60 1920x1200p60 2560x1600p601024x768p50 1280x768p50 1344x1008p50 1600x1200p50 1920x1440p50 3840x2160p251024x768p60 1280x768p60 1344x1008p60 1600x1200p60 1920x1440p60 3840x2160p301152x864p50 1280x800p50 1360x768p50 1680x1050p50 2048x1536p50 4096x2160p251152x864p60 1280x800p60 1360x768p60 1680x1050p60 2048x1536p60 4096x2160p30
The connected source device is free to ignore the EDID of the NGS-D320 When anothertiming is received the NGS-D320 will adapt to this timing as long as it is one of the 48supported timings
Output timingBy default the timing on the output video connector will be set to the first (preferred) detailed timing inthe EDID of the display The timing can also be set to a specific timing ignoring the EDID of the display
This is typically setup at the decoder side The decoded video will be resized and frame rate convertedto be shown full screen on the connected display When resizing aspect ratio will be kept
Refer to Decoder settings page 38on how to configure
At the output 3 modes are supported1 Preferred timing
In this setting the output timing of the device will be the first detailed timing descriptor in the EDID ofthe attached display
2 StandbyIn this setting the output syncs are disabled to make the connected display go to standby
3 SpecificIn this setting the NGS-D320 will not read the EDID from the connected display but will force theoutput as selected out of the 45 supported timings
Loop throughIt is possible to loop through the video amp audio from input to output connector
The loop through behavior is depending on the decoder settingsIf decoding is active no loop through shall be available
If decoding is not active (eg on an encoder) then the output will be a loop through of the input
The loop through will be active
10 K5903129 NGS-D320 29092016
2 Product information
bull 05 seconds after the input is connectedbull 2 seconds after the decoding is disabled
233 Network
DiscoveryNGS-D320 devices can be discovered on the network using the mDNS protocol
Refer to Discovery page 23 on how to discover an NGS-D320
IP addressingThe NGS-D320 supports IPv4 addressing
The IP address can be dynamically configured using DHCP or can be configured to static
If no DHCP is present and no static config is available the device will fall back to linklocal addressing
The NGS-D320 can connect to an NTP (Network Time Protocol) server
All media traffic will be timestamped according to this reference time
If no NTP server is present the media will be timestamped in line with the device clock (starting at 1 Jan1970) The device clock is reset after every reboot
The NGS-D320 can connect to a DNS (Domain Name Service) server
Refer to Network settings page 32 on how to configure NGS-D320 network settings
PortsThe table below lists the ports used for the various protocols on the NGS-D320
Port ProtocolTCP 443 https for web interface and APITCP 554 RTSPTCP 5901 VNC for keyboard amp mouse forwarding from decoder to encoderUDP 5004 RTP audio amp video streaming (5004 is the default port changeable by user)UDP 9875 Session announcements (SAP) on multicast address 2242127254
These ports need to be open on the network infrastructure to ensure proper operation
234 Streaming
Stream controlThe NGS-D320 supports 2 methods to control stream flow1 RTSP
The NGS-D320 supports RTSP (Real Time Streaming Protocol) and runs an RTSP server to manageconnections Connection to the NGS-D320 streams can be done via RTSP clientsBoth RTSP unicast amp multicast is supported
2 SAPThe NGS-D320 supports SAP (Session Announcement Protocol) and sends out SAP announcementsWhen subscribing to the SAP multicast address 2242127254 the SAP message of an NGS-D320will be available and will allow to connect to an NGS-D320 multicast stream
Media streamThe NGS-D320 uses RTP (Real Time Protocol) to stream media
K5903129 NGS-D320 29092016 11
2 Product information
Each encoded stream can have 2 destination addressesports
Device type Number of H264 streams Destination addressesportsNGS-D320 Lite 1 stream Stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSPNGS-D320 Pro 2 streams
bull from 2 different video inputs orbull the same video input encoded
with different quality
Each stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSP
SDPThe streams are described via SDP (Session Description Protocol) For each stream an SDP will beavailable
Refer to Encoder settings page 35 and Decoder settings page 38 to setup streamingon NGS-D320
235 Video
Video formatThe NGS-D320 encodes and decodes DVI HDMI and DP connections tofrom compressed H264 IPtraffic
The H264 stream is
bull IAW RFC3984 (RTP Payload Format for H264 Video)bull YUV420 format with 8-bit colordepth
Encoder profilesThe NGS-D320 encoder supports a number of H264 encoder profiles with varying stream profile levelbitrate framerate and maximum resolution
12 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
2 Product information
2 PRODUCT INFORMATION
21 Use cases
An NGS-D320 device enables hardware-accelerated KVMA-over-IP using standard 1GIPv4 networks It is connected to the network for transporting Audio Video and control
211 Media modes
Different media modesThe device can stream media in 3 different media modes to support various use cases
These 3 media modes are supported
bull Encoderbull Decoderbull Local
A brief description for each media mode is given below
EncoderThe device is typically connected to a desktop PC or server
The corresponding decoder can be
bull Another NGS-D320 devicebull A software based decoder
Install your NGS-D320 as an encoder
To decode use software decoding on a PCserver (eg VLC Media Player ) andor use another NGS-D320 as a decoder
This is illustrated below
1
2 3
4
5
6
7
8
9
9
9
Image 2-1Encoder installation
1 PC server2 NGS-D320 (encoder)3 Switch4 NGS-D320 (decoder)5 PC (SW decoder)6 Audio signal
K5903129 NGS-D320 29092016 5
2 Product information
7 Video signal8 USB HID9 Data (network)
Audio video and USB connections are made from the PC to the NGS-D320
The video content flows from the PCserver to the NGS-D320 the NGS-D320 encodes the video andthen the video is streamed onto the IP network
The audio content can be bi-directional audio can be sent to or received from the NGS-D320The USB peripheral port of the NGS-D320 connects to an USB host port on the PCserver The NGS-D320 emulates an USB HID device and events are sent from the NGS-D320 to the PCserver
DecoderThe device is typically connected to one or two screens Next to the screens the device can also beconnected to a headsetspeakermicrophone a keyboard and a mouse
The corresponding encoder can be
bull Another NGS-D320 devicebull Another Barco device compatible with the NGS-D320
Refer to the specific Barco Systems with NGS-D320 devices for compatible products
1
2
3 4
5
6 7
8
9
6
6
Image 2-2Decoder installation
1 NGS-D320 (encoder)2 Barco device or PCserver3 Switch4 NGS-D320 (decoder)5 Screen headsetspeakermicrophone keyboard or mouse6 Data (network)7 Audio signal8 Video signal9 USB HID
The video interfaces are connected to the screen(s)The audio interfaces are connected to a headset or speakers and a microphone can be connected to theNGS-D320
The keyboard and mouse connect to the USB host interfaces of the NGS-D320
LocalThis mode is a combination of the encoder amp decoder mode
The device is typically connected locally at a desktop position The device sits between the PCserverand the screens headsetspeakermicrophone keyboard and mouse The video audio amp USB cablesconnect from both ends to the NGS-D320 device
These inputs are locally looped through the device
The NGS-D320 device plugs into the network and is capable of streaming amp receiving network traffic si-multaneously
Install your NGS-D320 as illustrated below
6 K5903129 NGS-D320 29092016
2 Product information
1
2
3
4
6 7 8
5
6 7 8
Image 2-3Encoder and decoder installation
1 Screen headsetspeakermicrophone keyboard or mouse2 NGS-D320 (local)3 Barco device or PCserver4 Switch5 Data (network)6 Audio signal7 Video signal8 USB HID
Keyboard local settings To make sure all keys are operable the physical keyboardlayout at decoder side should match the keyboard configuration at encoder side (onPCserver)
212 Control modes
Different control modesThe device can be controlled in 2 modes
bull Locally or Unmanaged modebull Centrally or Managed mode
Unmanaged modeIn this mode the device is used stand-alone
Each device is controlled amp operated locally through its onboard web user interface
See Operation page 21 for details on how to configure amp operate the device
Managed modeIn this mode the device is used in a system
Each device is controlled amp operated centrally via a system controller which communicates with the devicethrough the device API
See the User Manual of the respective system on how to configure amp operate the device within the systemcontext
K5903129 NGS-D320 29092016 7
2 Product information
22 Models
221 Lite amp Pro
DifferencesThe NGS-D320 comes in 2 flavours a Lite and a Pro versionThemain difference between the 2models is the number of simultaneous video streams and display headsthat they support
Refer to Technical Specifications NGS-D320 Lite page 55 and Technical Specifications NGS-D320Pro page 57 for more details of the specifications
Model Lite ProNumberof H264streams
1 up to 2H264 streams
Use cases Encoder orDecoder
Local (EncoderDecoder) or
Dual channel encoder or
Dual channel decoderNumber ofsource inputs
1 up to 2Display heads1
Numberof displayoutputs
1 up to 2
Local use case NA Can be set up to encode 1 H264 stream ANDdecode 1 H264 stream from independentsources simultaneously
Level 51 NA Can only encode OR decode 1 L51 stream(up to 4K resolution) not 2
Maximum resolution 2560x1600 30fps
4096x2160 15fps
2 streams 2560x1600 30fps
1 stream 2560x1600 60fps
1 stream 4096x2160 30fps
Dual quality NA Can encode a single source (less than L51)twice in 2 different qualities
Dual channel NA Can encode both a DVI and a DisplayPortinput simultaneously
Priority principle If an input stream has L51 (4K) only one encoding shall be active
23 FeaturesOverviewThe device supports audio video amp USB media types on the network
In this section an explanation is given on the various features per media type as well as on the networkspecific features
Refer to Operation page 21 on how to configure the NGS-D320 for these features
1 Only one 4K H264 stream can be encoded or decoded at a time
8 K5903129 NGS-D320 29092016
2 Product information
231 Resources
Device behaviourDepending on the model an NGS-D320 has limited audio amp video encoding and decoding resources
A resource utilization algorithm is present on the NGS-D320 that ensures that the device will alwaysbehave in the same way when it is configured in the same way
Priority principleResources are not granted on a ldquofirst come first serverdquo principle but on a priority principle
The following priority principle is valid
bull Encoding always gets priority over decodingbull Encoding will be in order of priority DVI HDMI DPbull If an input stream is configured to use an L51 profile (eg for 4K) only encoding shall be activebull For Pro devices the first stream of an input type will have priority over second stream of the same
input type
These principles apply dynamically and in real-time depending on the actual device status These princi-ples are valid both for audio amp video
Some examples on the priority principle
bull A device is configured to encode 2 inputs (eg 1 DP and 1 DVI) and also configured to decode 1output (eg 1 DVI or 1 DP)When the 2 inputs are active (active syncs detected) the device will only encode decoding will bedisabledIf one of the 2 inputs drops (no active sync detected) the decoding will start automatically
bull A device is configured to encode 1 DP input and 1 DVI inputIf the DP input is 4K resolution (L51) then only the DP input encoding will be activeIf the DP input resolution changes to 1920x1080 then the DVI input encoding will automatically acti-vate
bull A Pro device is configured to encode 1 DP input in 2 qualities and 1 DVI inputThe DVI will be encodedOnly the first configured DP stream will be encoded
ReportingThe actual status of resource utilization is reported continuously via Diagnostics
232 EDID
EDID supportThe NGS-D320 supports EDID at both the input and ouput The EDID can be setup for each input andoutput individually and independently
InputThe EDID at the input is the EDID as seen by the PC This is typically setup at the encoder side Referto Encoder settings page 35 on how to configure
At the input 2 settings are supported
K5903129 NGS-D320 29092016 9
2 Product information
1 Default4 timings will be supported on the source PC with 1920x1200p60 as preferred timing
1920x1200p60
1920x1080p60
2560x1600p603840x2160p30
2 SpecificIn this setting only one specific timing will be providedThe specific timing can be selected out of a list of 46 timings
640x480p50 1176x664p50 1280x960p50 1440x900p50 1920x1080p50 2560x1440p50
640x480p60 1176x664p60 1280x960p60 1440x900p60 1920x1080p60 2560x1440p60
800x600p50 1280x720p50 1280x1024p50 1600x1024p50 1920x1200p50 2560x1600p50800x600p60 1280x720p60 1280x1024p60 1600x1024p60 1920x1200p60 2560x1600p601024x768p50 1280x768p50 1344x1008p50 1600x1200p50 1920x1440p50 3840x2160p251024x768p60 1280x768p60 1344x1008p60 1600x1200p60 1920x1440p60 3840x2160p301152x864p50 1280x800p50 1360x768p50 1680x1050p50 2048x1536p50 4096x2160p251152x864p60 1280x800p60 1360x768p60 1680x1050p60 2048x1536p60 4096x2160p30
The connected source device is free to ignore the EDID of the NGS-D320 When anothertiming is received the NGS-D320 will adapt to this timing as long as it is one of the 48supported timings
Output timingBy default the timing on the output video connector will be set to the first (preferred) detailed timing inthe EDID of the display The timing can also be set to a specific timing ignoring the EDID of the display
This is typically setup at the decoder side The decoded video will be resized and frame rate convertedto be shown full screen on the connected display When resizing aspect ratio will be kept
Refer to Decoder settings page 38on how to configure
At the output 3 modes are supported1 Preferred timing
In this setting the output timing of the device will be the first detailed timing descriptor in the EDID ofthe attached display
2 StandbyIn this setting the output syncs are disabled to make the connected display go to standby
3 SpecificIn this setting the NGS-D320 will not read the EDID from the connected display but will force theoutput as selected out of the 45 supported timings
Loop throughIt is possible to loop through the video amp audio from input to output connector
The loop through behavior is depending on the decoder settingsIf decoding is active no loop through shall be available
If decoding is not active (eg on an encoder) then the output will be a loop through of the input
The loop through will be active
10 K5903129 NGS-D320 29092016
2 Product information
bull 05 seconds after the input is connectedbull 2 seconds after the decoding is disabled
233 Network
DiscoveryNGS-D320 devices can be discovered on the network using the mDNS protocol
Refer to Discovery page 23 on how to discover an NGS-D320
IP addressingThe NGS-D320 supports IPv4 addressing
The IP address can be dynamically configured using DHCP or can be configured to static
If no DHCP is present and no static config is available the device will fall back to linklocal addressing
The NGS-D320 can connect to an NTP (Network Time Protocol) server
All media traffic will be timestamped according to this reference time
If no NTP server is present the media will be timestamped in line with the device clock (starting at 1 Jan1970) The device clock is reset after every reboot
The NGS-D320 can connect to a DNS (Domain Name Service) server
Refer to Network settings page 32 on how to configure NGS-D320 network settings
PortsThe table below lists the ports used for the various protocols on the NGS-D320
Port ProtocolTCP 443 https for web interface and APITCP 554 RTSPTCP 5901 VNC for keyboard amp mouse forwarding from decoder to encoderUDP 5004 RTP audio amp video streaming (5004 is the default port changeable by user)UDP 9875 Session announcements (SAP) on multicast address 2242127254
These ports need to be open on the network infrastructure to ensure proper operation
234 Streaming
Stream controlThe NGS-D320 supports 2 methods to control stream flow1 RTSP
The NGS-D320 supports RTSP (Real Time Streaming Protocol) and runs an RTSP server to manageconnections Connection to the NGS-D320 streams can be done via RTSP clientsBoth RTSP unicast amp multicast is supported
2 SAPThe NGS-D320 supports SAP (Session Announcement Protocol) and sends out SAP announcementsWhen subscribing to the SAP multicast address 2242127254 the SAP message of an NGS-D320will be available and will allow to connect to an NGS-D320 multicast stream
Media streamThe NGS-D320 uses RTP (Real Time Protocol) to stream media
K5903129 NGS-D320 29092016 11
2 Product information
Each encoded stream can have 2 destination addressesports
Device type Number of H264 streams Destination addressesportsNGS-D320 Lite 1 stream Stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSPNGS-D320 Pro 2 streams
bull from 2 different video inputs orbull the same video input encoded
with different quality
Each stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSP
SDPThe streams are described via SDP (Session Description Protocol) For each stream an SDP will beavailable
Refer to Encoder settings page 35 and Decoder settings page 38 to setup streamingon NGS-D320
235 Video
Video formatThe NGS-D320 encodes and decodes DVI HDMI and DP connections tofrom compressed H264 IPtraffic
The H264 stream is
bull IAW RFC3984 (RTP Payload Format for H264 Video)bull YUV420 format with 8-bit colordepth
Encoder profilesThe NGS-D320 encoder supports a number of H264 encoder profiles with varying stream profile levelbitrate framerate and maximum resolution
12 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
2 Product information
7 Video signal8 USB HID9 Data (network)
Audio video and USB connections are made from the PC to the NGS-D320
The video content flows from the PCserver to the NGS-D320 the NGS-D320 encodes the video andthen the video is streamed onto the IP network
The audio content can be bi-directional audio can be sent to or received from the NGS-D320The USB peripheral port of the NGS-D320 connects to an USB host port on the PCserver The NGS-D320 emulates an USB HID device and events are sent from the NGS-D320 to the PCserver
DecoderThe device is typically connected to one or two screens Next to the screens the device can also beconnected to a headsetspeakermicrophone a keyboard and a mouse
The corresponding encoder can be
bull Another NGS-D320 devicebull Another Barco device compatible with the NGS-D320
Refer to the specific Barco Systems with NGS-D320 devices for compatible products
1
2
3 4
5
6 7
8
9
6
6
Image 2-2Decoder installation
1 NGS-D320 (encoder)2 Barco device or PCserver3 Switch4 NGS-D320 (decoder)5 Screen headsetspeakermicrophone keyboard or mouse6 Data (network)7 Audio signal8 Video signal9 USB HID
The video interfaces are connected to the screen(s)The audio interfaces are connected to a headset or speakers and a microphone can be connected to theNGS-D320
The keyboard and mouse connect to the USB host interfaces of the NGS-D320
LocalThis mode is a combination of the encoder amp decoder mode
The device is typically connected locally at a desktop position The device sits between the PCserverand the screens headsetspeakermicrophone keyboard and mouse The video audio amp USB cablesconnect from both ends to the NGS-D320 device
These inputs are locally looped through the device
The NGS-D320 device plugs into the network and is capable of streaming amp receiving network traffic si-multaneously
Install your NGS-D320 as illustrated below
6 K5903129 NGS-D320 29092016
2 Product information
1
2
3
4
6 7 8
5
6 7 8
Image 2-3Encoder and decoder installation
1 Screen headsetspeakermicrophone keyboard or mouse2 NGS-D320 (local)3 Barco device or PCserver4 Switch5 Data (network)6 Audio signal7 Video signal8 USB HID
Keyboard local settings To make sure all keys are operable the physical keyboardlayout at decoder side should match the keyboard configuration at encoder side (onPCserver)
212 Control modes
Different control modesThe device can be controlled in 2 modes
bull Locally or Unmanaged modebull Centrally or Managed mode
Unmanaged modeIn this mode the device is used stand-alone
Each device is controlled amp operated locally through its onboard web user interface
See Operation page 21 for details on how to configure amp operate the device
Managed modeIn this mode the device is used in a system
Each device is controlled amp operated centrally via a system controller which communicates with the devicethrough the device API
See the User Manual of the respective system on how to configure amp operate the device within the systemcontext
K5903129 NGS-D320 29092016 7
2 Product information
22 Models
221 Lite amp Pro
DifferencesThe NGS-D320 comes in 2 flavours a Lite and a Pro versionThemain difference between the 2models is the number of simultaneous video streams and display headsthat they support
Refer to Technical Specifications NGS-D320 Lite page 55 and Technical Specifications NGS-D320Pro page 57 for more details of the specifications
Model Lite ProNumberof H264streams
1 up to 2H264 streams
Use cases Encoder orDecoder
Local (EncoderDecoder) or
Dual channel encoder or
Dual channel decoderNumber ofsource inputs
1 up to 2Display heads1
Numberof displayoutputs
1 up to 2
Local use case NA Can be set up to encode 1 H264 stream ANDdecode 1 H264 stream from independentsources simultaneously
Level 51 NA Can only encode OR decode 1 L51 stream(up to 4K resolution) not 2
Maximum resolution 2560x1600 30fps
4096x2160 15fps
2 streams 2560x1600 30fps
1 stream 2560x1600 60fps
1 stream 4096x2160 30fps
Dual quality NA Can encode a single source (less than L51)twice in 2 different qualities
Dual channel NA Can encode both a DVI and a DisplayPortinput simultaneously
Priority principle If an input stream has L51 (4K) only one encoding shall be active
23 FeaturesOverviewThe device supports audio video amp USB media types on the network
In this section an explanation is given on the various features per media type as well as on the networkspecific features
Refer to Operation page 21 on how to configure the NGS-D320 for these features
1 Only one 4K H264 stream can be encoded or decoded at a time
8 K5903129 NGS-D320 29092016
2 Product information
231 Resources
Device behaviourDepending on the model an NGS-D320 has limited audio amp video encoding and decoding resources
A resource utilization algorithm is present on the NGS-D320 that ensures that the device will alwaysbehave in the same way when it is configured in the same way
Priority principleResources are not granted on a ldquofirst come first serverdquo principle but on a priority principle
The following priority principle is valid
bull Encoding always gets priority over decodingbull Encoding will be in order of priority DVI HDMI DPbull If an input stream is configured to use an L51 profile (eg for 4K) only encoding shall be activebull For Pro devices the first stream of an input type will have priority over second stream of the same
input type
These principles apply dynamically and in real-time depending on the actual device status These princi-ples are valid both for audio amp video
Some examples on the priority principle
bull A device is configured to encode 2 inputs (eg 1 DP and 1 DVI) and also configured to decode 1output (eg 1 DVI or 1 DP)When the 2 inputs are active (active syncs detected) the device will only encode decoding will bedisabledIf one of the 2 inputs drops (no active sync detected) the decoding will start automatically
bull A device is configured to encode 1 DP input and 1 DVI inputIf the DP input is 4K resolution (L51) then only the DP input encoding will be activeIf the DP input resolution changes to 1920x1080 then the DVI input encoding will automatically acti-vate
bull A Pro device is configured to encode 1 DP input in 2 qualities and 1 DVI inputThe DVI will be encodedOnly the first configured DP stream will be encoded
ReportingThe actual status of resource utilization is reported continuously via Diagnostics
232 EDID
EDID supportThe NGS-D320 supports EDID at both the input and ouput The EDID can be setup for each input andoutput individually and independently
InputThe EDID at the input is the EDID as seen by the PC This is typically setup at the encoder side Referto Encoder settings page 35 on how to configure
At the input 2 settings are supported
K5903129 NGS-D320 29092016 9
2 Product information
1 Default4 timings will be supported on the source PC with 1920x1200p60 as preferred timing
1920x1200p60
1920x1080p60
2560x1600p603840x2160p30
2 SpecificIn this setting only one specific timing will be providedThe specific timing can be selected out of a list of 46 timings
640x480p50 1176x664p50 1280x960p50 1440x900p50 1920x1080p50 2560x1440p50
640x480p60 1176x664p60 1280x960p60 1440x900p60 1920x1080p60 2560x1440p60
800x600p50 1280x720p50 1280x1024p50 1600x1024p50 1920x1200p50 2560x1600p50800x600p60 1280x720p60 1280x1024p60 1600x1024p60 1920x1200p60 2560x1600p601024x768p50 1280x768p50 1344x1008p50 1600x1200p50 1920x1440p50 3840x2160p251024x768p60 1280x768p60 1344x1008p60 1600x1200p60 1920x1440p60 3840x2160p301152x864p50 1280x800p50 1360x768p50 1680x1050p50 2048x1536p50 4096x2160p251152x864p60 1280x800p60 1360x768p60 1680x1050p60 2048x1536p60 4096x2160p30
The connected source device is free to ignore the EDID of the NGS-D320 When anothertiming is received the NGS-D320 will adapt to this timing as long as it is one of the 48supported timings
Output timingBy default the timing on the output video connector will be set to the first (preferred) detailed timing inthe EDID of the display The timing can also be set to a specific timing ignoring the EDID of the display
This is typically setup at the decoder side The decoded video will be resized and frame rate convertedto be shown full screen on the connected display When resizing aspect ratio will be kept
Refer to Decoder settings page 38on how to configure
At the output 3 modes are supported1 Preferred timing
In this setting the output timing of the device will be the first detailed timing descriptor in the EDID ofthe attached display
2 StandbyIn this setting the output syncs are disabled to make the connected display go to standby
3 SpecificIn this setting the NGS-D320 will not read the EDID from the connected display but will force theoutput as selected out of the 45 supported timings
Loop throughIt is possible to loop through the video amp audio from input to output connector
The loop through behavior is depending on the decoder settingsIf decoding is active no loop through shall be available
If decoding is not active (eg on an encoder) then the output will be a loop through of the input
The loop through will be active
10 K5903129 NGS-D320 29092016
2 Product information
bull 05 seconds after the input is connectedbull 2 seconds after the decoding is disabled
233 Network
DiscoveryNGS-D320 devices can be discovered on the network using the mDNS protocol
Refer to Discovery page 23 on how to discover an NGS-D320
IP addressingThe NGS-D320 supports IPv4 addressing
The IP address can be dynamically configured using DHCP or can be configured to static
If no DHCP is present and no static config is available the device will fall back to linklocal addressing
The NGS-D320 can connect to an NTP (Network Time Protocol) server
All media traffic will be timestamped according to this reference time
If no NTP server is present the media will be timestamped in line with the device clock (starting at 1 Jan1970) The device clock is reset after every reboot
The NGS-D320 can connect to a DNS (Domain Name Service) server
Refer to Network settings page 32 on how to configure NGS-D320 network settings
PortsThe table below lists the ports used for the various protocols on the NGS-D320
Port ProtocolTCP 443 https for web interface and APITCP 554 RTSPTCP 5901 VNC for keyboard amp mouse forwarding from decoder to encoderUDP 5004 RTP audio amp video streaming (5004 is the default port changeable by user)UDP 9875 Session announcements (SAP) on multicast address 2242127254
These ports need to be open on the network infrastructure to ensure proper operation
234 Streaming
Stream controlThe NGS-D320 supports 2 methods to control stream flow1 RTSP
The NGS-D320 supports RTSP (Real Time Streaming Protocol) and runs an RTSP server to manageconnections Connection to the NGS-D320 streams can be done via RTSP clientsBoth RTSP unicast amp multicast is supported
2 SAPThe NGS-D320 supports SAP (Session Announcement Protocol) and sends out SAP announcementsWhen subscribing to the SAP multicast address 2242127254 the SAP message of an NGS-D320will be available and will allow to connect to an NGS-D320 multicast stream
Media streamThe NGS-D320 uses RTP (Real Time Protocol) to stream media
K5903129 NGS-D320 29092016 11
2 Product information
Each encoded stream can have 2 destination addressesports
Device type Number of H264 streams Destination addressesportsNGS-D320 Lite 1 stream Stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSPNGS-D320 Pro 2 streams
bull from 2 different video inputs orbull the same video input encoded
with different quality
Each stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSP
SDPThe streams are described via SDP (Session Description Protocol) For each stream an SDP will beavailable
Refer to Encoder settings page 35 and Decoder settings page 38 to setup streamingon NGS-D320
235 Video
Video formatThe NGS-D320 encodes and decodes DVI HDMI and DP connections tofrom compressed H264 IPtraffic
The H264 stream is
bull IAW RFC3984 (RTP Payload Format for H264 Video)bull YUV420 format with 8-bit colordepth
Encoder profilesThe NGS-D320 encoder supports a number of H264 encoder profiles with varying stream profile levelbitrate framerate and maximum resolution
12 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
2 Product information
1
2
3
4
6 7 8
5
6 7 8
Image 2-3Encoder and decoder installation
1 Screen headsetspeakermicrophone keyboard or mouse2 NGS-D320 (local)3 Barco device or PCserver4 Switch5 Data (network)6 Audio signal7 Video signal8 USB HID
Keyboard local settings To make sure all keys are operable the physical keyboardlayout at decoder side should match the keyboard configuration at encoder side (onPCserver)
212 Control modes
Different control modesThe device can be controlled in 2 modes
bull Locally or Unmanaged modebull Centrally or Managed mode
Unmanaged modeIn this mode the device is used stand-alone
Each device is controlled amp operated locally through its onboard web user interface
See Operation page 21 for details on how to configure amp operate the device
Managed modeIn this mode the device is used in a system
Each device is controlled amp operated centrally via a system controller which communicates with the devicethrough the device API
See the User Manual of the respective system on how to configure amp operate the device within the systemcontext
K5903129 NGS-D320 29092016 7
2 Product information
22 Models
221 Lite amp Pro
DifferencesThe NGS-D320 comes in 2 flavours a Lite and a Pro versionThemain difference between the 2models is the number of simultaneous video streams and display headsthat they support
Refer to Technical Specifications NGS-D320 Lite page 55 and Technical Specifications NGS-D320Pro page 57 for more details of the specifications
Model Lite ProNumberof H264streams
1 up to 2H264 streams
Use cases Encoder orDecoder
Local (EncoderDecoder) or
Dual channel encoder or
Dual channel decoderNumber ofsource inputs
1 up to 2Display heads1
Numberof displayoutputs
1 up to 2
Local use case NA Can be set up to encode 1 H264 stream ANDdecode 1 H264 stream from independentsources simultaneously
Level 51 NA Can only encode OR decode 1 L51 stream(up to 4K resolution) not 2
Maximum resolution 2560x1600 30fps
4096x2160 15fps
2 streams 2560x1600 30fps
1 stream 2560x1600 60fps
1 stream 4096x2160 30fps
Dual quality NA Can encode a single source (less than L51)twice in 2 different qualities
Dual channel NA Can encode both a DVI and a DisplayPortinput simultaneously
Priority principle If an input stream has L51 (4K) only one encoding shall be active
23 FeaturesOverviewThe device supports audio video amp USB media types on the network
In this section an explanation is given on the various features per media type as well as on the networkspecific features
Refer to Operation page 21 on how to configure the NGS-D320 for these features
1 Only one 4K H264 stream can be encoded or decoded at a time
8 K5903129 NGS-D320 29092016
2 Product information
231 Resources
Device behaviourDepending on the model an NGS-D320 has limited audio amp video encoding and decoding resources
A resource utilization algorithm is present on the NGS-D320 that ensures that the device will alwaysbehave in the same way when it is configured in the same way
Priority principleResources are not granted on a ldquofirst come first serverdquo principle but on a priority principle
The following priority principle is valid
bull Encoding always gets priority over decodingbull Encoding will be in order of priority DVI HDMI DPbull If an input stream is configured to use an L51 profile (eg for 4K) only encoding shall be activebull For Pro devices the first stream of an input type will have priority over second stream of the same
input type
These principles apply dynamically and in real-time depending on the actual device status These princi-ples are valid both for audio amp video
Some examples on the priority principle
bull A device is configured to encode 2 inputs (eg 1 DP and 1 DVI) and also configured to decode 1output (eg 1 DVI or 1 DP)When the 2 inputs are active (active syncs detected) the device will only encode decoding will bedisabledIf one of the 2 inputs drops (no active sync detected) the decoding will start automatically
bull A device is configured to encode 1 DP input and 1 DVI inputIf the DP input is 4K resolution (L51) then only the DP input encoding will be activeIf the DP input resolution changes to 1920x1080 then the DVI input encoding will automatically acti-vate
bull A Pro device is configured to encode 1 DP input in 2 qualities and 1 DVI inputThe DVI will be encodedOnly the first configured DP stream will be encoded
ReportingThe actual status of resource utilization is reported continuously via Diagnostics
232 EDID
EDID supportThe NGS-D320 supports EDID at both the input and ouput The EDID can be setup for each input andoutput individually and independently
InputThe EDID at the input is the EDID as seen by the PC This is typically setup at the encoder side Referto Encoder settings page 35 on how to configure
At the input 2 settings are supported
K5903129 NGS-D320 29092016 9
2 Product information
1 Default4 timings will be supported on the source PC with 1920x1200p60 as preferred timing
1920x1200p60
1920x1080p60
2560x1600p603840x2160p30
2 SpecificIn this setting only one specific timing will be providedThe specific timing can be selected out of a list of 46 timings
640x480p50 1176x664p50 1280x960p50 1440x900p50 1920x1080p50 2560x1440p50
640x480p60 1176x664p60 1280x960p60 1440x900p60 1920x1080p60 2560x1440p60
800x600p50 1280x720p50 1280x1024p50 1600x1024p50 1920x1200p50 2560x1600p50800x600p60 1280x720p60 1280x1024p60 1600x1024p60 1920x1200p60 2560x1600p601024x768p50 1280x768p50 1344x1008p50 1600x1200p50 1920x1440p50 3840x2160p251024x768p60 1280x768p60 1344x1008p60 1600x1200p60 1920x1440p60 3840x2160p301152x864p50 1280x800p50 1360x768p50 1680x1050p50 2048x1536p50 4096x2160p251152x864p60 1280x800p60 1360x768p60 1680x1050p60 2048x1536p60 4096x2160p30
The connected source device is free to ignore the EDID of the NGS-D320 When anothertiming is received the NGS-D320 will adapt to this timing as long as it is one of the 48supported timings
Output timingBy default the timing on the output video connector will be set to the first (preferred) detailed timing inthe EDID of the display The timing can also be set to a specific timing ignoring the EDID of the display
This is typically setup at the decoder side The decoded video will be resized and frame rate convertedto be shown full screen on the connected display When resizing aspect ratio will be kept
Refer to Decoder settings page 38on how to configure
At the output 3 modes are supported1 Preferred timing
In this setting the output timing of the device will be the first detailed timing descriptor in the EDID ofthe attached display
2 StandbyIn this setting the output syncs are disabled to make the connected display go to standby
3 SpecificIn this setting the NGS-D320 will not read the EDID from the connected display but will force theoutput as selected out of the 45 supported timings
Loop throughIt is possible to loop through the video amp audio from input to output connector
The loop through behavior is depending on the decoder settingsIf decoding is active no loop through shall be available
If decoding is not active (eg on an encoder) then the output will be a loop through of the input
The loop through will be active
10 K5903129 NGS-D320 29092016
2 Product information
bull 05 seconds after the input is connectedbull 2 seconds after the decoding is disabled
233 Network
DiscoveryNGS-D320 devices can be discovered on the network using the mDNS protocol
Refer to Discovery page 23 on how to discover an NGS-D320
IP addressingThe NGS-D320 supports IPv4 addressing
The IP address can be dynamically configured using DHCP or can be configured to static
If no DHCP is present and no static config is available the device will fall back to linklocal addressing
The NGS-D320 can connect to an NTP (Network Time Protocol) server
All media traffic will be timestamped according to this reference time
If no NTP server is present the media will be timestamped in line with the device clock (starting at 1 Jan1970) The device clock is reset after every reboot
The NGS-D320 can connect to a DNS (Domain Name Service) server
Refer to Network settings page 32 on how to configure NGS-D320 network settings
PortsThe table below lists the ports used for the various protocols on the NGS-D320
Port ProtocolTCP 443 https for web interface and APITCP 554 RTSPTCP 5901 VNC for keyboard amp mouse forwarding from decoder to encoderUDP 5004 RTP audio amp video streaming (5004 is the default port changeable by user)UDP 9875 Session announcements (SAP) on multicast address 2242127254
These ports need to be open on the network infrastructure to ensure proper operation
234 Streaming
Stream controlThe NGS-D320 supports 2 methods to control stream flow1 RTSP
The NGS-D320 supports RTSP (Real Time Streaming Protocol) and runs an RTSP server to manageconnections Connection to the NGS-D320 streams can be done via RTSP clientsBoth RTSP unicast amp multicast is supported
2 SAPThe NGS-D320 supports SAP (Session Announcement Protocol) and sends out SAP announcementsWhen subscribing to the SAP multicast address 2242127254 the SAP message of an NGS-D320will be available and will allow to connect to an NGS-D320 multicast stream
Media streamThe NGS-D320 uses RTP (Real Time Protocol) to stream media
K5903129 NGS-D320 29092016 11
2 Product information
Each encoded stream can have 2 destination addressesports
Device type Number of H264 streams Destination addressesportsNGS-D320 Lite 1 stream Stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSPNGS-D320 Pro 2 streams
bull from 2 different video inputs orbull the same video input encoded
with different quality
Each stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSP
SDPThe streams are described via SDP (Session Description Protocol) For each stream an SDP will beavailable
Refer to Encoder settings page 35 and Decoder settings page 38 to setup streamingon NGS-D320
235 Video
Video formatThe NGS-D320 encodes and decodes DVI HDMI and DP connections tofrom compressed H264 IPtraffic
The H264 stream is
bull IAW RFC3984 (RTP Payload Format for H264 Video)bull YUV420 format with 8-bit colordepth
Encoder profilesThe NGS-D320 encoder supports a number of H264 encoder profiles with varying stream profile levelbitrate framerate and maximum resolution
12 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
2 Product information
22 Models
221 Lite amp Pro
DifferencesThe NGS-D320 comes in 2 flavours a Lite and a Pro versionThemain difference between the 2models is the number of simultaneous video streams and display headsthat they support
Refer to Technical Specifications NGS-D320 Lite page 55 and Technical Specifications NGS-D320Pro page 57 for more details of the specifications
Model Lite ProNumberof H264streams
1 up to 2H264 streams
Use cases Encoder orDecoder
Local (EncoderDecoder) or
Dual channel encoder or
Dual channel decoderNumber ofsource inputs
1 up to 2Display heads1
Numberof displayoutputs
1 up to 2
Local use case NA Can be set up to encode 1 H264 stream ANDdecode 1 H264 stream from independentsources simultaneously
Level 51 NA Can only encode OR decode 1 L51 stream(up to 4K resolution) not 2
Maximum resolution 2560x1600 30fps
4096x2160 15fps
2 streams 2560x1600 30fps
1 stream 2560x1600 60fps
1 stream 4096x2160 30fps
Dual quality NA Can encode a single source (less than L51)twice in 2 different qualities
Dual channel NA Can encode both a DVI and a DisplayPortinput simultaneously
Priority principle If an input stream has L51 (4K) only one encoding shall be active
23 FeaturesOverviewThe device supports audio video amp USB media types on the network
In this section an explanation is given on the various features per media type as well as on the networkspecific features
Refer to Operation page 21 on how to configure the NGS-D320 for these features
1 Only one 4K H264 stream can be encoded or decoded at a time
8 K5903129 NGS-D320 29092016
2 Product information
231 Resources
Device behaviourDepending on the model an NGS-D320 has limited audio amp video encoding and decoding resources
A resource utilization algorithm is present on the NGS-D320 that ensures that the device will alwaysbehave in the same way when it is configured in the same way
Priority principleResources are not granted on a ldquofirst come first serverdquo principle but on a priority principle
The following priority principle is valid
bull Encoding always gets priority over decodingbull Encoding will be in order of priority DVI HDMI DPbull If an input stream is configured to use an L51 profile (eg for 4K) only encoding shall be activebull For Pro devices the first stream of an input type will have priority over second stream of the same
input type
These principles apply dynamically and in real-time depending on the actual device status These princi-ples are valid both for audio amp video
Some examples on the priority principle
bull A device is configured to encode 2 inputs (eg 1 DP and 1 DVI) and also configured to decode 1output (eg 1 DVI or 1 DP)When the 2 inputs are active (active syncs detected) the device will only encode decoding will bedisabledIf one of the 2 inputs drops (no active sync detected) the decoding will start automatically
bull A device is configured to encode 1 DP input and 1 DVI inputIf the DP input is 4K resolution (L51) then only the DP input encoding will be activeIf the DP input resolution changes to 1920x1080 then the DVI input encoding will automatically acti-vate
bull A Pro device is configured to encode 1 DP input in 2 qualities and 1 DVI inputThe DVI will be encodedOnly the first configured DP stream will be encoded
ReportingThe actual status of resource utilization is reported continuously via Diagnostics
232 EDID
EDID supportThe NGS-D320 supports EDID at both the input and ouput The EDID can be setup for each input andoutput individually and independently
InputThe EDID at the input is the EDID as seen by the PC This is typically setup at the encoder side Referto Encoder settings page 35 on how to configure
At the input 2 settings are supported
K5903129 NGS-D320 29092016 9
2 Product information
1 Default4 timings will be supported on the source PC with 1920x1200p60 as preferred timing
1920x1200p60
1920x1080p60
2560x1600p603840x2160p30
2 SpecificIn this setting only one specific timing will be providedThe specific timing can be selected out of a list of 46 timings
640x480p50 1176x664p50 1280x960p50 1440x900p50 1920x1080p50 2560x1440p50
640x480p60 1176x664p60 1280x960p60 1440x900p60 1920x1080p60 2560x1440p60
800x600p50 1280x720p50 1280x1024p50 1600x1024p50 1920x1200p50 2560x1600p50800x600p60 1280x720p60 1280x1024p60 1600x1024p60 1920x1200p60 2560x1600p601024x768p50 1280x768p50 1344x1008p50 1600x1200p50 1920x1440p50 3840x2160p251024x768p60 1280x768p60 1344x1008p60 1600x1200p60 1920x1440p60 3840x2160p301152x864p50 1280x800p50 1360x768p50 1680x1050p50 2048x1536p50 4096x2160p251152x864p60 1280x800p60 1360x768p60 1680x1050p60 2048x1536p60 4096x2160p30
The connected source device is free to ignore the EDID of the NGS-D320 When anothertiming is received the NGS-D320 will adapt to this timing as long as it is one of the 48supported timings
Output timingBy default the timing on the output video connector will be set to the first (preferred) detailed timing inthe EDID of the display The timing can also be set to a specific timing ignoring the EDID of the display
This is typically setup at the decoder side The decoded video will be resized and frame rate convertedto be shown full screen on the connected display When resizing aspect ratio will be kept
Refer to Decoder settings page 38on how to configure
At the output 3 modes are supported1 Preferred timing
In this setting the output timing of the device will be the first detailed timing descriptor in the EDID ofthe attached display
2 StandbyIn this setting the output syncs are disabled to make the connected display go to standby
3 SpecificIn this setting the NGS-D320 will not read the EDID from the connected display but will force theoutput as selected out of the 45 supported timings
Loop throughIt is possible to loop through the video amp audio from input to output connector
The loop through behavior is depending on the decoder settingsIf decoding is active no loop through shall be available
If decoding is not active (eg on an encoder) then the output will be a loop through of the input
The loop through will be active
10 K5903129 NGS-D320 29092016
2 Product information
bull 05 seconds after the input is connectedbull 2 seconds after the decoding is disabled
233 Network
DiscoveryNGS-D320 devices can be discovered on the network using the mDNS protocol
Refer to Discovery page 23 on how to discover an NGS-D320
IP addressingThe NGS-D320 supports IPv4 addressing
The IP address can be dynamically configured using DHCP or can be configured to static
If no DHCP is present and no static config is available the device will fall back to linklocal addressing
The NGS-D320 can connect to an NTP (Network Time Protocol) server
All media traffic will be timestamped according to this reference time
If no NTP server is present the media will be timestamped in line with the device clock (starting at 1 Jan1970) The device clock is reset after every reboot
The NGS-D320 can connect to a DNS (Domain Name Service) server
Refer to Network settings page 32 on how to configure NGS-D320 network settings
PortsThe table below lists the ports used for the various protocols on the NGS-D320
Port ProtocolTCP 443 https for web interface and APITCP 554 RTSPTCP 5901 VNC for keyboard amp mouse forwarding from decoder to encoderUDP 5004 RTP audio amp video streaming (5004 is the default port changeable by user)UDP 9875 Session announcements (SAP) on multicast address 2242127254
These ports need to be open on the network infrastructure to ensure proper operation
234 Streaming
Stream controlThe NGS-D320 supports 2 methods to control stream flow1 RTSP
The NGS-D320 supports RTSP (Real Time Streaming Protocol) and runs an RTSP server to manageconnections Connection to the NGS-D320 streams can be done via RTSP clientsBoth RTSP unicast amp multicast is supported
2 SAPThe NGS-D320 supports SAP (Session Announcement Protocol) and sends out SAP announcementsWhen subscribing to the SAP multicast address 2242127254 the SAP message of an NGS-D320will be available and will allow to connect to an NGS-D320 multicast stream
Media streamThe NGS-D320 uses RTP (Real Time Protocol) to stream media
K5903129 NGS-D320 29092016 11
2 Product information
Each encoded stream can have 2 destination addressesports
Device type Number of H264 streams Destination addressesportsNGS-D320 Lite 1 stream Stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSPNGS-D320 Pro 2 streams
bull from 2 different video inputs orbull the same video input encoded
with different quality
Each stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSP
SDPThe streams are described via SDP (Session Description Protocol) For each stream an SDP will beavailable
Refer to Encoder settings page 35 and Decoder settings page 38 to setup streamingon NGS-D320
235 Video
Video formatThe NGS-D320 encodes and decodes DVI HDMI and DP connections tofrom compressed H264 IPtraffic
The H264 stream is
bull IAW RFC3984 (RTP Payload Format for H264 Video)bull YUV420 format with 8-bit colordepth
Encoder profilesThe NGS-D320 encoder supports a number of H264 encoder profiles with varying stream profile levelbitrate framerate and maximum resolution
12 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
2 Product information
231 Resources
Device behaviourDepending on the model an NGS-D320 has limited audio amp video encoding and decoding resources
A resource utilization algorithm is present on the NGS-D320 that ensures that the device will alwaysbehave in the same way when it is configured in the same way
Priority principleResources are not granted on a ldquofirst come first serverdquo principle but on a priority principle
The following priority principle is valid
bull Encoding always gets priority over decodingbull Encoding will be in order of priority DVI HDMI DPbull If an input stream is configured to use an L51 profile (eg for 4K) only encoding shall be activebull For Pro devices the first stream of an input type will have priority over second stream of the same
input type
These principles apply dynamically and in real-time depending on the actual device status These princi-ples are valid both for audio amp video
Some examples on the priority principle
bull A device is configured to encode 2 inputs (eg 1 DP and 1 DVI) and also configured to decode 1output (eg 1 DVI or 1 DP)When the 2 inputs are active (active syncs detected) the device will only encode decoding will bedisabledIf one of the 2 inputs drops (no active sync detected) the decoding will start automatically
bull A device is configured to encode 1 DP input and 1 DVI inputIf the DP input is 4K resolution (L51) then only the DP input encoding will be activeIf the DP input resolution changes to 1920x1080 then the DVI input encoding will automatically acti-vate
bull A Pro device is configured to encode 1 DP input in 2 qualities and 1 DVI inputThe DVI will be encodedOnly the first configured DP stream will be encoded
ReportingThe actual status of resource utilization is reported continuously via Diagnostics
232 EDID
EDID supportThe NGS-D320 supports EDID at both the input and ouput The EDID can be setup for each input andoutput individually and independently
InputThe EDID at the input is the EDID as seen by the PC This is typically setup at the encoder side Referto Encoder settings page 35 on how to configure
At the input 2 settings are supported
K5903129 NGS-D320 29092016 9
2 Product information
1 Default4 timings will be supported on the source PC with 1920x1200p60 as preferred timing
1920x1200p60
1920x1080p60
2560x1600p603840x2160p30
2 SpecificIn this setting only one specific timing will be providedThe specific timing can be selected out of a list of 46 timings
640x480p50 1176x664p50 1280x960p50 1440x900p50 1920x1080p50 2560x1440p50
640x480p60 1176x664p60 1280x960p60 1440x900p60 1920x1080p60 2560x1440p60
800x600p50 1280x720p50 1280x1024p50 1600x1024p50 1920x1200p50 2560x1600p50800x600p60 1280x720p60 1280x1024p60 1600x1024p60 1920x1200p60 2560x1600p601024x768p50 1280x768p50 1344x1008p50 1600x1200p50 1920x1440p50 3840x2160p251024x768p60 1280x768p60 1344x1008p60 1600x1200p60 1920x1440p60 3840x2160p301152x864p50 1280x800p50 1360x768p50 1680x1050p50 2048x1536p50 4096x2160p251152x864p60 1280x800p60 1360x768p60 1680x1050p60 2048x1536p60 4096x2160p30
The connected source device is free to ignore the EDID of the NGS-D320 When anothertiming is received the NGS-D320 will adapt to this timing as long as it is one of the 48supported timings
Output timingBy default the timing on the output video connector will be set to the first (preferred) detailed timing inthe EDID of the display The timing can also be set to a specific timing ignoring the EDID of the display
This is typically setup at the decoder side The decoded video will be resized and frame rate convertedto be shown full screen on the connected display When resizing aspect ratio will be kept
Refer to Decoder settings page 38on how to configure
At the output 3 modes are supported1 Preferred timing
In this setting the output timing of the device will be the first detailed timing descriptor in the EDID ofthe attached display
2 StandbyIn this setting the output syncs are disabled to make the connected display go to standby
3 SpecificIn this setting the NGS-D320 will not read the EDID from the connected display but will force theoutput as selected out of the 45 supported timings
Loop throughIt is possible to loop through the video amp audio from input to output connector
The loop through behavior is depending on the decoder settingsIf decoding is active no loop through shall be available
If decoding is not active (eg on an encoder) then the output will be a loop through of the input
The loop through will be active
10 K5903129 NGS-D320 29092016
2 Product information
bull 05 seconds after the input is connectedbull 2 seconds after the decoding is disabled
233 Network
DiscoveryNGS-D320 devices can be discovered on the network using the mDNS protocol
Refer to Discovery page 23 on how to discover an NGS-D320
IP addressingThe NGS-D320 supports IPv4 addressing
The IP address can be dynamically configured using DHCP or can be configured to static
If no DHCP is present and no static config is available the device will fall back to linklocal addressing
The NGS-D320 can connect to an NTP (Network Time Protocol) server
All media traffic will be timestamped according to this reference time
If no NTP server is present the media will be timestamped in line with the device clock (starting at 1 Jan1970) The device clock is reset after every reboot
The NGS-D320 can connect to a DNS (Domain Name Service) server
Refer to Network settings page 32 on how to configure NGS-D320 network settings
PortsThe table below lists the ports used for the various protocols on the NGS-D320
Port ProtocolTCP 443 https for web interface and APITCP 554 RTSPTCP 5901 VNC for keyboard amp mouse forwarding from decoder to encoderUDP 5004 RTP audio amp video streaming (5004 is the default port changeable by user)UDP 9875 Session announcements (SAP) on multicast address 2242127254
These ports need to be open on the network infrastructure to ensure proper operation
234 Streaming
Stream controlThe NGS-D320 supports 2 methods to control stream flow1 RTSP
The NGS-D320 supports RTSP (Real Time Streaming Protocol) and runs an RTSP server to manageconnections Connection to the NGS-D320 streams can be done via RTSP clientsBoth RTSP unicast amp multicast is supported
2 SAPThe NGS-D320 supports SAP (Session Announcement Protocol) and sends out SAP announcementsWhen subscribing to the SAP multicast address 2242127254 the SAP message of an NGS-D320will be available and will allow to connect to an NGS-D320 multicast stream
Media streamThe NGS-D320 uses RTP (Real Time Protocol) to stream media
K5903129 NGS-D320 29092016 11
2 Product information
Each encoded stream can have 2 destination addressesports
Device type Number of H264 streams Destination addressesportsNGS-D320 Lite 1 stream Stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSPNGS-D320 Pro 2 streams
bull from 2 different video inputs orbull the same video input encoded
with different quality
Each stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSP
SDPThe streams are described via SDP (Session Description Protocol) For each stream an SDP will beavailable
Refer to Encoder settings page 35 and Decoder settings page 38 to setup streamingon NGS-D320
235 Video
Video formatThe NGS-D320 encodes and decodes DVI HDMI and DP connections tofrom compressed H264 IPtraffic
The H264 stream is
bull IAW RFC3984 (RTP Payload Format for H264 Video)bull YUV420 format with 8-bit colordepth
Encoder profilesThe NGS-D320 encoder supports a number of H264 encoder profiles with varying stream profile levelbitrate framerate and maximum resolution
12 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
2 Product information
1 Default4 timings will be supported on the source PC with 1920x1200p60 as preferred timing
1920x1200p60
1920x1080p60
2560x1600p603840x2160p30
2 SpecificIn this setting only one specific timing will be providedThe specific timing can be selected out of a list of 46 timings
640x480p50 1176x664p50 1280x960p50 1440x900p50 1920x1080p50 2560x1440p50
640x480p60 1176x664p60 1280x960p60 1440x900p60 1920x1080p60 2560x1440p60
800x600p50 1280x720p50 1280x1024p50 1600x1024p50 1920x1200p50 2560x1600p50800x600p60 1280x720p60 1280x1024p60 1600x1024p60 1920x1200p60 2560x1600p601024x768p50 1280x768p50 1344x1008p50 1600x1200p50 1920x1440p50 3840x2160p251024x768p60 1280x768p60 1344x1008p60 1600x1200p60 1920x1440p60 3840x2160p301152x864p50 1280x800p50 1360x768p50 1680x1050p50 2048x1536p50 4096x2160p251152x864p60 1280x800p60 1360x768p60 1680x1050p60 2048x1536p60 4096x2160p30
The connected source device is free to ignore the EDID of the NGS-D320 When anothertiming is received the NGS-D320 will adapt to this timing as long as it is one of the 48supported timings
Output timingBy default the timing on the output video connector will be set to the first (preferred) detailed timing inthe EDID of the display The timing can also be set to a specific timing ignoring the EDID of the display
This is typically setup at the decoder side The decoded video will be resized and frame rate convertedto be shown full screen on the connected display When resizing aspect ratio will be kept
Refer to Decoder settings page 38on how to configure
At the output 3 modes are supported1 Preferred timing
In this setting the output timing of the device will be the first detailed timing descriptor in the EDID ofthe attached display
2 StandbyIn this setting the output syncs are disabled to make the connected display go to standby
3 SpecificIn this setting the NGS-D320 will not read the EDID from the connected display but will force theoutput as selected out of the 45 supported timings
Loop throughIt is possible to loop through the video amp audio from input to output connector
The loop through behavior is depending on the decoder settingsIf decoding is active no loop through shall be available
If decoding is not active (eg on an encoder) then the output will be a loop through of the input
The loop through will be active
10 K5903129 NGS-D320 29092016
2 Product information
bull 05 seconds after the input is connectedbull 2 seconds after the decoding is disabled
233 Network
DiscoveryNGS-D320 devices can be discovered on the network using the mDNS protocol
Refer to Discovery page 23 on how to discover an NGS-D320
IP addressingThe NGS-D320 supports IPv4 addressing
The IP address can be dynamically configured using DHCP or can be configured to static
If no DHCP is present and no static config is available the device will fall back to linklocal addressing
The NGS-D320 can connect to an NTP (Network Time Protocol) server
All media traffic will be timestamped according to this reference time
If no NTP server is present the media will be timestamped in line with the device clock (starting at 1 Jan1970) The device clock is reset after every reboot
The NGS-D320 can connect to a DNS (Domain Name Service) server
Refer to Network settings page 32 on how to configure NGS-D320 network settings
PortsThe table below lists the ports used for the various protocols on the NGS-D320
Port ProtocolTCP 443 https for web interface and APITCP 554 RTSPTCP 5901 VNC for keyboard amp mouse forwarding from decoder to encoderUDP 5004 RTP audio amp video streaming (5004 is the default port changeable by user)UDP 9875 Session announcements (SAP) on multicast address 2242127254
These ports need to be open on the network infrastructure to ensure proper operation
234 Streaming
Stream controlThe NGS-D320 supports 2 methods to control stream flow1 RTSP
The NGS-D320 supports RTSP (Real Time Streaming Protocol) and runs an RTSP server to manageconnections Connection to the NGS-D320 streams can be done via RTSP clientsBoth RTSP unicast amp multicast is supported
2 SAPThe NGS-D320 supports SAP (Session Announcement Protocol) and sends out SAP announcementsWhen subscribing to the SAP multicast address 2242127254 the SAP message of an NGS-D320will be available and will allow to connect to an NGS-D320 multicast stream
Media streamThe NGS-D320 uses RTP (Real Time Protocol) to stream media
K5903129 NGS-D320 29092016 11
2 Product information
Each encoded stream can have 2 destination addressesports
Device type Number of H264 streams Destination addressesportsNGS-D320 Lite 1 stream Stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSPNGS-D320 Pro 2 streams
bull from 2 different video inputs orbull the same video input encoded
with different quality
Each stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSP
SDPThe streams are described via SDP (Session Description Protocol) For each stream an SDP will beavailable
Refer to Encoder settings page 35 and Decoder settings page 38 to setup streamingon NGS-D320
235 Video
Video formatThe NGS-D320 encodes and decodes DVI HDMI and DP connections tofrom compressed H264 IPtraffic
The H264 stream is
bull IAW RFC3984 (RTP Payload Format for H264 Video)bull YUV420 format with 8-bit colordepth
Encoder profilesThe NGS-D320 encoder supports a number of H264 encoder profiles with varying stream profile levelbitrate framerate and maximum resolution
12 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
2 Product information
bull 05 seconds after the input is connectedbull 2 seconds after the decoding is disabled
233 Network
DiscoveryNGS-D320 devices can be discovered on the network using the mDNS protocol
Refer to Discovery page 23 on how to discover an NGS-D320
IP addressingThe NGS-D320 supports IPv4 addressing
The IP address can be dynamically configured using DHCP or can be configured to static
If no DHCP is present and no static config is available the device will fall back to linklocal addressing
The NGS-D320 can connect to an NTP (Network Time Protocol) server
All media traffic will be timestamped according to this reference time
If no NTP server is present the media will be timestamped in line with the device clock (starting at 1 Jan1970) The device clock is reset after every reboot
The NGS-D320 can connect to a DNS (Domain Name Service) server
Refer to Network settings page 32 on how to configure NGS-D320 network settings
PortsThe table below lists the ports used for the various protocols on the NGS-D320
Port ProtocolTCP 443 https for web interface and APITCP 554 RTSPTCP 5901 VNC for keyboard amp mouse forwarding from decoder to encoderUDP 5004 RTP audio amp video streaming (5004 is the default port changeable by user)UDP 9875 Session announcements (SAP) on multicast address 2242127254
These ports need to be open on the network infrastructure to ensure proper operation
234 Streaming
Stream controlThe NGS-D320 supports 2 methods to control stream flow1 RTSP
The NGS-D320 supports RTSP (Real Time Streaming Protocol) and runs an RTSP server to manageconnections Connection to the NGS-D320 streams can be done via RTSP clientsBoth RTSP unicast amp multicast is supported
2 SAPThe NGS-D320 supports SAP (Session Announcement Protocol) and sends out SAP announcementsWhen subscribing to the SAP multicast address 2242127254 the SAP message of an NGS-D320will be available and will allow to connect to an NGS-D320 multicast stream
Media streamThe NGS-D320 uses RTP (Real Time Protocol) to stream media
K5903129 NGS-D320 29092016 11
2 Product information
Each encoded stream can have 2 destination addressesports
Device type Number of H264 streams Destination addressesportsNGS-D320 Lite 1 stream Stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSPNGS-D320 Pro 2 streams
bull from 2 different video inputs orbull the same video input encoded
with different quality
Each stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSP
SDPThe streams are described via SDP (Session Description Protocol) For each stream an SDP will beavailable
Refer to Encoder settings page 35 and Decoder settings page 38 to setup streamingon NGS-D320
235 Video
Video formatThe NGS-D320 encodes and decodes DVI HDMI and DP connections tofrom compressed H264 IPtraffic
The H264 stream is
bull IAW RFC3984 (RTP Payload Format for H264 Video)bull YUV420 format with 8-bit colordepth
Encoder profilesThe NGS-D320 encoder supports a number of H264 encoder profiles with varying stream profile levelbitrate framerate and maximum resolution
12 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
2 Product information
Each encoded stream can have 2 destination addressesports
Device type Number of H264 streams Destination addressesportsNGS-D320 Lite 1 stream Stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSPNGS-D320 Pro 2 streams
bull from 2 different video inputs orbull the same video input encoded
with different quality
Each stream can have 2 destinations
bull Two unicasts negotiated through RTSP orbull One fixed multicastunicast or AND one
unicast negotiated through RTSP
SDPThe streams are described via SDP (Session Description Protocol) For each stream an SDP will beavailable
Refer to Encoder settings page 35 and Decoder settings page 38 to setup streamingon NGS-D320
235 Video
Video formatThe NGS-D320 encodes and decodes DVI HDMI and DP connections tofrom compressed H264 IPtraffic
The H264 stream is
bull IAW RFC3984 (RTP Payload Format for H264 Video)bull YUV420 format with 8-bit colordepth
Encoder profilesThe NGS-D320 encoder supports a number of H264 encoder profiles with varying stream profile levelbitrate framerate and maximum resolution
12 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
2 Product information
1 Stream ProfileA profile defines a set of capabilities targeting a specific class of applications3 stream profiles are supported on NGS-D320
Stream profile Characteristics Target decodingplatform
BASE Supports a limited subset of techniques simpler todesign less code less processing power
Low power mobiledevices
MAIN Supports the majority of techniques more complex todesign more code more memory needs amp CPU load
Standard PC
NGS-D320 decoderHIGH Supports the complex techniques most complex to
design most code highest memory amp CPU loadHigh-end workstation
NGS-D320 decoder
2 LevelsA level is a specified set of constraints that indicated a degree of required decoder performance for aprofileA level specifies- Maximum resolution- Maximum frame rate- Maximum bitratethat a decoder must be capable to decodeA decoder that conforms to a level must be able to decode all bitstreams encoded for that level andall lower levelsThe NGS-D320 supports L40 L50 and L51
3 Resolution amp Frame RateThe NGS-D320 supports the following maximum resolutions amp frame rates
Maximum resolutionFrame rate Lite (1 stream) Pro (both streams)
60fps 1920x1200 1920x120030fps 2560x1600 2560x160015fps 4096x2160 4096x2160 (1 stream)60fps NA 2560x1600 (1 stream)30fps NA 4096x2160 (1 stream)
4 BitratesThe NGS-D320 supports following bitrates- Minimum bitrate 512Kbs- Maximum bitrate
o Lite 12Mbso Pro 24Mbs
5 Profile namingThe profiles on the NGS-D320 are named according to following definitionH264 ltstream profilegtltbitrategtltmax resolutiongtltmax framerategt (ltgdrgt)All profiles are IDR profiles except the profiles with gdr extensionIDR stands for ldquoInstantaneous Decoder Refreshrdquo The IDR profiles generate I-frames I-frames aresent every 30 framesSee Note below
K5903129 NGS-D320 29092016 13
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
2 Product information
6 Auto profileBy default the NGS-D320 encoder profile is set to ldquoautordquoIn this option the device will automatically select a profile based on the input resolution it detectsThe table shows the auto-selected profile
Resolution Profilelt= 1920x1200 main_8m_2mp_60gt 1920x1200 and lt= 2560x1600 high_12m_4mp_30gt 2560x1600 high_12m_8mp_15
7 GDR profileGDR stands for ldquoGradual Decoder Refreshrdquo This is a profile that does not generate I-frames in orderto optimize bandwidth amp latencyThe main drawbacks are that not all H264 decoders can handle GDR profiles and that switching timeat the decoder could increase as there is no I-frame in the stream to sync switching toIf the NGS-D320 encoder is used with any other H264 decoder you can select a GDR profile andattempt to decode it but if the decoder behavior is unreliable it is recommended to select a non GDRprofileThe NGS-D320 decoder can handle GDR profiles and in an NGS-D320 encoderNGS-D320 decodersetup we recommend to configure the encoder to a GDR profile to achieve optimal latency perfor-manceThe NGS-D320 supports GDR for a number of H264 encoder profiles Refer to Settings page 32on how to configure
8 Source downscalingThe selected profile may result in downscaling of the input source resolution to the maximum resolutionsupported by this profileThe below table shows an example
Input Profile Stream outmain_4m_2mp_60 H264 stream 60Hz 1920x1200main_4m_4mp_30 H264 stream 30Hz 2560x1600
2560x1600p60
base_512_1mp_60 H264 stream 60Hz 1280x800
Profile naming The gdr extension only applies to a limited number of profiles See alsothe explanation on the GDR profile
DecodingWhen an NGS-D320 is setup to encode H264 streams these streams can be decoded either in hardware(eg on another NGS-D320) or in software (on a standard PC)1 Hardware
The NGS-D320 supports H264 hardware decodingThe Lite and Pro model limitations apply similar to decoding as to encodingThe device can not just decode any H264 stream on the network it can only decode H264 streamsgenerated by another NGS-D320Do not attempt to decode H264 streams from other sources as this could lead to unreliable behavioreg from artifacts in the image to no image at allFor setting up hardware decoding refer to Decoder settings page 38
2 SoftwareThe NGS-D320 video and audio streams can be software decoded on a standard PC using applica-tions like VLC Quicktime Media Player hellipPerformance of the decoding is dependent on the combination of the H264 stream profile and the PCspecifications
14 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
2 Product information
236 Audio
Audio formatThe NGS-D320 supports encoding and decoding 1 stream of Uncompressed RAW audioiaw
bull RFC3551 (RTP Profile for Audio amp Video Conferences with Minimal Control)bull RFC2586 (AudioL16 MIME content type)
AssociationThe audio stream can be configured to be Associated with a video stream but Association can also bedisabled for audio streams which are independent of the video
237 USB HID
Remote controlThe NGS-D320 supports the use of keyboard and mouse to enable remote control of connected sourcesover the network
HID events are sent across the network iaw VNC (RFB) protocol (RFC6143)
Hardware decodingWhen having a setup between an NGS-D320 encoder and NGS-D320 decoder then
bull Connect any USB keyboard and mouse to the decoderbull Connect the PC via USB to the encoderbull Set the PC keyboard local to match the actual connected keyboard (either use rdquolocalerdquo or use ldquolayoutrdquo)The network is transparent for keyboard operation The keyboard acts just as if it was connected to thePC locally via a USB cable
By default the NGS-D320 is configured to have keyboard and mouse operational
The keyboard and mouse can be disabled refer to Encoder settings page 35
Software decodingWhen having a setup between an NGS-D320 encoder and another Barco software decoder refer to theuser manual of this specific system
When having a setup between an NGS-D320 encoder and a 3rd party software decoder then keyboardand mouse can function by running a VNC client on the software decoder However interoperability andfluent operation cannot be guaranteed
K5903129 NGS-D320 29092016 15
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
2 Product information
16 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
3 Installation
3 INSTALLATIONDiagramsBelow is an overview of how to connect the signal cables of the NGS-D320 with other devices Connectthe unit as shown in the following diagrams
CAUTION Keep the space around the fans free so that the ventilation air is not ob-structed
The MAC address of the device can be found on a label at the bottom of the device
31 Front viewIllustrationThe front view of the NGS-D320 is illustrated below
Image 3-1Front view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
K5903129 NGS-D320 29092016 17
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
3 Installation
14 13 12 11
81 2 3 4 75 6 9 10Image 3-2Front connections of the NGS-D320
Connectorpart Connecting deviceuse1 DVI In LED Orange There is no DVI In signal
Green There is valid DVI In signal2 Video Input DVI-D DVI-D input (dual link)
3 DVI Out LED Orange No display attached to DVI out
Green Display attached to DVI out
4 Video Output DVI-D DVI-D output (dual link)
5 HDMI In LED Orange There is no HDMI In signal
Green There is valid HDMI In signal6 Video Input HDMI HDMI Input
7 HDMI Out LED Orange No display attached to HDMI out
Green Display attached to HDMI out8 Video Output HDMI HDMI Output
9 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power10 Identification LED On Upgrading the device firmware (do NOT cut
power from the device)
Blinking Identification11 Display port output Display port output
12 DP Out LED Orange No display attached to DP out
Green Display attached to DP out13 Display port input Display port input
14 DP In LED Orange There is no DP In signal
Green There is valid DP In signal
It is advised to use dual link DVI cables for the interconnections
18 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
3 Installation
32 Rear viewIllustrationThe rear view of the NGS-D320 is illustrated below
Image 3-3Rear view of the NGS-D320
Connection detailsThe NGS-D320 provides the connections as shown below
111 2 3 4 5 6 7 9 10
8
12Image 3-4Rear connections of the NGS-D320
Connectorpart Connecting deviceuse1 Power input Power source (12V DC)
2 Power LED Green Power OK
Red Wrong power supply connected Functionalityis not guaranteed
Off No power
K5903129 NGS-D320 29092016 19
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
3 Installation
Connectorpart Connecting deviceuse3 Identification LED Blue On Upgrading the device firmware (do NOT
cut power from the device)
Blue Blinking Identification4 3D input Stereo (3D)
5 Headset inout Headset
6 Audio line out Audio device (eg PC LS)
7 Audio line in Audio device (eg PC)
8 Ground Ground
9 USB interface type A (3) USB 20 type A keyboard andor mouse
10 Micro USB interface Micro USB connector to PC
11 Ethernet interface (RJ45) cage Dual 1Gb Ethernet connection
Left connector secondary 1Gb ethernet connection
Right connector primary 1Gb ethernet connection
For both RJ45 connectors there are two LEDsinside
bull Left LED (green) activity (Blinking=activity OFF=no activity)
bull Right LED (green) link status (ON=link present OFF=no link present)
12 Push button Identification button
33 Start upHow to start up the device1 After installing the device as mentioned above apply power to the power source (12V DC)
2 Check if the Power LED is lit green
3 Check if the applied input and output LEDs are lit green
20 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
4 OPERATION
41 IntroductionUnmanaged modeThis section explains how to discover configure amp operate your NGS-D320 device when being used inUnmanaged control mode (refer to Control modes page 7 vfor an overview of the Control Modes)
42 Web interface
421 Introduction
Unmanaged modeWhen the device is used in unmanaged mode the device is configured through the web user interface(WebUI) it exposes
422 Browser support
WebUI accessThe WebUI can be accessed over https protocol
The WebUI is supported in all major browsers in their current release at the time of writing
bull Internet Explorerbull Mozilla Firefoxbull Google Chromebull Safari
423 WebUI overview
Main menusThe WebUI consists of 3 main menus each with their own submenus
Image 4-1WebUI main menus
The following menus are available
Main Menu Submenu Description
Info General info on the device
Diagnostics Detailed diagnostics info of the deviceAdministration Administration of the device
Device Info
Help Help section of the device
K5903129 NGS-D320 29092016 21
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
Main Menu Submenu Description
Network settings Network configurationEncoder settings Configure amp use as encoderDecoder settings Configure amp use as decoder
Settings
Power settings Configure DPMS settingsDiscovery Discover all NGS-D320 devices in the network
If you change a setting the Apply button appears press this button to con-firm the change If you leave the page with unsaved changes a warning message willappear
If you refresh your browser (eg via F5 on Windows machines) then you will be takenback to the login screen This is due to the nature of how the webUI is designed There-fore you will note that certain pages contain a Refresh button which only refresh theactual page being displayed
424 Login
IntroductionOpen your browser and navigate to the device by entering the IP address of the device
Image 4-2Login
To find the IP address of the device see chapter 4 Operation Discovery page 23
Browse to the devicersquos website eg https1921680100The security warning appears because the device has no DNS hostname but hosts anhttps website (using a self-signed certificate) Browsers will show this as insecure be-cause they have no proof of the identity of the device (in contradiction with true securesites that do prove their identity through an externally signed certificate) The interac-tion through this website however is secure (it can not be listened in)
First loginUpon first login an administrator password MUST be set for the device
22 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
A pop-up dialog will appear where one can set the administrator password
Image 4-3New password
Fill in the new administrator password confirm and press Set password
LoginAfter initial login there are 2 access levels for the webUI
bull UserThe webUI is read only no changes can be made- User name user- The initial user password is ltemptygt- A new user password can be set in the Administration section (refer to image 4-3 for explanation)
bull AdministratorThe webUI is fully accessible all changes can be made- User name admin- The initial admin password was set an initial logon- The admin password can be changed in the Adminstration section (refer to image 4-3 for explana-tion)
Once logged in the webUI of the device shows up
Logout
Press the logout button to log out
43 Discovery
431 Introduction
Discovery methodsBefore you can operate your device(s) you must know its (their) location in the network The location isdefined by the devicersquos IP address
The IP address can be discovered using one of these methods
K5903129 NGS-D320 29092016 23
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
bull Barco Device Discovery Toolbull Discovery via OSDbull Web Interface Discoverybull Identification button
Once you have found one NGS-D320 device you can easily find other NGS-D320 devices from its webuser interface Refer to the sections below for more details
432 Barco Device Discovery Tool
ProcedureThe Barco Device Discovery Tool is available at httpwwwbarcocomnetworktools
1
3
2
Image 4-4Barco Device Discovery Tool
1 Select NGS-D3202 Choose the device serial number from the list or enter the serial number in the space below to quickly
find the device3 Click the link to access the NGS-D320 setup Wizard
433 Discovery via OSD
Detection1 Connect a display to the device and start up
2 Detect the IP address of your NGS-D320 via the OSD display output
24 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
Image 4-5OSD display output
434 Web Interface Discovery
WebUI procedureTo be able to discover other NGS-D320 devices from the web UI of one NGS-D320 device you must firstlog in to this device1 Login (Login page 22)
2 Select the tab Discovery
Image 4-6Discovery
3 The system starts searching the network and lists all devices linked to your network
4 The table lists this information for your NGS-D320- ID Identification LED is lit or not (lightbulb)- Name Name of the device in the system- Encoder AudioVideo inputs 2
- Decoder AudioVideo outputs3
- IP address Device IP addressMore information on the device (software version serial numberhellip) can be shown in the table by click-
ingThis table is read-only It cannot be used for multiple device configuration accross the network Toachieve that the device must be used in Managed mode in a system
5 Press the light bulb in the table above (image 4-6) The corresponding device will be put in or out ofIdentification modeA device in Identification mode will blink the blue identification LED and put an identification messagein overlay on all video outputs
2 Blue when actively receiving signal (This doesnrsquot mean it is encoded it means there is an active and correct signal present at thisinterface)3 Blue see above
K5903129 NGS-D320 29092016 25
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
435 Identification button
Identification of a device1 Press the identification button on a deviceThe device is put in Identification mode The blue light bulbs in the table above (image 4-6) will be bluefor all devices currently in Identification mode
Tip You might need to refresh the table by pressing to update the data to the current status
44 Device info
441 Introduction
Device Info menuIn this menu you can perform a general device setup1 Select the tab Device Info to start
Image 4-7Device Info _ Menu
2 You can choose one of these tabs to modify the settings- Info- Diagnostics- Administration- Help
26 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
442 Info
Overview1 Select the tab Info
Image 4-8Device Info _ Info
The Info page provides the information on the device listed below
NameThe host name of the device is shown here
Change the name here and give it a meaningful name
ModelThe device model is shown here
Serial numberThe device serial number is shown here
Software versionThe version of the software loaded onto the device is shown here
ConnectorsAll available connectors on the device are listed here
Only the active connectors are highlighted blue
K5903129 NGS-D320 29092016 27
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
443 Diagnostics
Introduction1 Select the tab Diagnostics2 Press Refresh to make sure you get the most recent data
Image 4-9Device Info _ Diagnostics
The Diagnostics page provides real-time detailed diagnostics information of the actual device statusThis information can be useful during configuration and troubleshooting
Download system logs1 Press the link Download system logs to start downloading a ldquologtxtrdquo file to your system2 Open the ldquologtxtrdquo file It provides a detailed technical status log of the device The information in this
log can be useful for troubleshooting or can be requested by Barco personnel during support
Log files are reset after a reboot
Download status plain text1 Press the link Download status plain text to start downloading a ldquodiagnosticstxtrdquo file to your system2 Open the ldquodiagnosticstxtrdquo file It provides the device status overview in a plain text format
Refresh button1 Press theRefresh button before reviewing the diagnostics page to ensure the latest up-to-date device
info is shown2 Status overviewResources general device resources (CPU memory uptime)
ServiceDiscovery information on the system controller (managed mode only)XMPPagent status of the system controller communication channel (managed mode only)
28 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
DPIn status of the DisplayPort inputDPOut status of the DisplayPort outputDVIIn status of the DVI inputDVIOut status of the DVI outputHDMIIn status of the HDMI input
HDMIOut status of the HDMI outputAudioIn status of the analog audio inputAudioOut status of the analog audio outputVNCClient information on the VNC client for the HID communications channelRtspserver status of the RTSP server
The RTSP server lists the SDP of any configured stream in the Media section This SDPcan be copied from the WebUI into a text file and saved with extension sdp Such SDPfile could then be used with applications like VLC
Image 4-10SDP
444 Administration
IntroductionSelect the tab Administration
K5903129 NGS-D320 29092016 29
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
Image 4-11Device Info _ Administration
Login1 Change the Administrator password select admin and type the new password with confirmation2 Change the User password select user and type the new password with confirmation
The password must have a length of minimum 6 characters
Device accessConfigure the device acces with these two checkboxes1 Allow user (read-only) access
- When checked the user can login to the device webUI with the user account password The userobtains read-only access
- When unchecked the user account cannot access the webUI2 Allow Barco service access
- When checked the user can have ssh (secure shell) access to the device- When unchecked ssh access is disabled (default)
Device settingsChange the device settings as such
Image 4-12Device Info _ Device settings
30 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
1 RebootPress Reboot to perform an immediate device soft reboot
2 Save Restore- Press Backup configuration to download the complete device configuration in a human readableformatOpen the fileNote The device configuration file does not contain any static IP configured settings nor the ad-ministrator password
- Press Restore configuration to upload a specific device configuration file3 Factory Defaults Reset
Perform a factory default reset via the WebUI or via the Identification button of the device
- WebUIPress Reset to factory defaultsNote this method will reset all encoderdecoder settings to factory defaults but the network settingsand the administrator password are NOT reset
- Identification buttona) Shut down the deviceb) Startup the device while keeping the Identification button pressedSee Installation page 17 for the location of this button
c) The identification LED will blink for 1 secondNote This method will reset ALL device settings to factory default including network and pass-word settings
445 Software upgrade
How to perform a software upgrade There are three methods to perform software upgrade1 Upgrade by uploading a deb filea) Press the link Browse for a local upgrade file and select the correct fileb) Press Start upgrade (the button appears once you have selected your upgrade file)c) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
2 Upgrade from a repository via http linka) Click on ldquoUpgrade urlrdquo and fill in the http to the deb fileb) Press Start upgradec) The blue identification LED is lit during the upgraded) Follow the upgrade status on the web interfacee) The device will reboot when upgrade is done
3 Upgrade from USB sticka) Put the deb file on USB storage and insert it into one of the USB portsUpgrade starts automatically
b) The blue identification LED is lit during the upgradec) Wait until the identification LED is offd) Remove USB stick and re-power the device
446 Help
Product documentationSelect the tab Help
K5903129 NGS-D320 29092016 31
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
Image 4-13Device Info _ Help
The Help page provides a link to the mybarco website where the product documentation can be found
45 Settings
451 Introduction
Settings menuIn this menu you can configure the devicersquos operational behavior on the network1 Select the tab Settings to start
Image 4-14Settings _ Menu
2 You can choose one of these tabs to modify the settings- Network Settings- Encoder Settings- Decoder Settings- Power Settings
452 Network settings
OverviewSelect the tab Network Settings
32 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
Image 4-15Settings _ Network settings
1 IP Settings2 Managed Mode3 SNMP settings
Here you can configure your device on the network
The NGS-D320 is designed to operate on standard IPv4 networks The device can be added to any IPv4network following standard network setup practices
4521 IP settings
DefaultBy default the device is configured to Dynamic IP addressing using DHCP
bull The DHCP server will automatically provide the device with the following network configuration- IP address- Subnet mask- Gateway address- NTP server address (if available)- DNS server address (if available)
bull The settings will be grayed out and are non-changeable
ConfigureTo configure the device to Static IP addressing1 Select Static2 Fill in the
K5903129 NGS-D320 29092016 33
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
- IP address- Subnet mask- Gateway addressNote The gateway must be set for proper network operation
- NTP server address (if applicable)- DNS server address (if applicable)
3 Press Apply (refer to the Note in WebUI overview page 21 for more information you may need toscroll down for this button)
Device not foundWhen no DHCP server is present in the local network and the device is not configured to Static IP ad-dressing
bull The device will fall back to a link-local address eg 169254xxbull Any other connected device in that network segment will also have a link-local addressbull As such communication with the device is still possiblebull To be able to discover the device in such scenario see Discovery page 23 Use any of the methods
described there to discover the link-local IP address of the device
4522 Managed mode
IntroductionThe Managed Mode is enabled by default and is required for operating the device in a larger system(Control modes page 7 for an overview of the operational modes)
Enabling this by default allows a system user to configure all devices from a central point in the systemwithout first having to go to each box individually to enable managed mode hereby defeating the conceptof having a system
Refer to the applicable Barco Management System Installation Guide to operate the device in this mode
Select Managed Mode (slide the bullet to the right) to enable the device to be managed by the system
Automatically discover serverbull By default this is switched on (bullet to the right) and the device will automatically attempt to discover
the management server- If a management server is found the devicersquos configuration is synchronized with the managementserver and the device can be controlled by the management server
- If no management server is found the device will fall back to unmanaged modebull In case you want to define the server yourself switch off (slide the bullet to the left) fill in the Server
IP address and press Apply
Use self registrationbull By default this is switched on (bullet to the right) and the device will automatically register itself with
the management serverbull In case you want to register the device manually switch off (slide the bullet to the left) define a User
name and Password for registration and press Apply
Manually setting the management server and the registration credentials can be re-quired to adhere to security policies
34 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
4523 Unmanaged mode
How to switch to Unmanged ModeTo use the device only in Unmanaged Mode and prohibit the use of Managed Mode switch off (slide thebullet to the left)Press Apply to save the settings
Unmanaged control mode is described in Control modes page 7
4524 SNMP settings
Configure1 Fill in the IP address or hostname of the host machine which is running your SNMPmonitoring softwareSNMP traps like reboots and temperature alarms will be sent to this host
453 Encoder settings
4531 Overview
Encoder settings tab1 Select the tab Encoder Settings
Image 4-16Settings _ Encoder settings
The Encoder Settings page allows to set up the device for encoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available input connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connec-tion is live This allows to pre-configure the device in advance
4532 Audio
Microphone In Line In1 Select Microphone or Line In to be configured for streaming
Image 4-17Encoder settings Audio In
K5903129 NGS-D320 29092016 35
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
2 The Gain is by default set to 50 Move the slider to adjust the gain3 The audio Encoding profile is by default set to ldquoUncompressed L-16rdquo No other profiles are availableTo disable the audio encoding Select (disabled) in the encoding profile drop down list
4 Define the destinationport in the Destination field- Multicast enter the valid multicast addressport- Unicast leave the destination field empty
5 Define the Time to Live under ttl This is by default set to 56 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can be used toconnect an RTSP client to the NGS-D320
7 Press Apply to save settings
4533 DVI InDP InHDMI In
Input EDID1 By default the Input EDID is set to ldquoDefault EDIDrdquoChoose the desired Input EDID setting in the Input EDID drop down box Select the default setting orone of the specific timings
Image 4-18Encoder settings DVI In DP In HDMI In
On NGS-D320 Lite devices only Stream 0 can be configured
On NGS-D320 Pro devices Stream 0 amp 1 can be configured independently
2 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
3 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4 Define the Time to Live under ttl This is by default set to 5
5 The RTSP url can be copied from the rtsp link Right click rtsp and save as This url can used toconnect an RTSP client to the NGS-D320
36 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
- Associated audioBy default the audio stream is Associated with the video stream This also means the RTSP url ofthe video stream will provide both the audio amp video stream (via a combined SDP)This association can also be disabled This means audio amp video streams are sent separately
- Associated USBBy default the USB HID stream is Associated with the video stream This means that this specificvideo port can be remote controlledThis also means the RTSP url of the video stream will provide both the USB HID amp video stream(via a combined SDP)This association can also be disabled This means USB amp video streams are sent separately
Note Combined SDPs do not work correctly with VLC Video will not play back
Disable the associated audio amp USB to allow software decode amp video playback with VLC
6 Press Apply to save settings
4534 HDMI Audio In
1 The Encoding profile is by default set to ldquoautordquo Select the desired Encoding profileTo disable Encoding explicitly for an input Select (disabled) in the encoding profile drop down list
Image 4-19Encoder settings HDMI Audio In
2 Define the destinationport in the Destination field- Multicast valid multicast addressport- Unicast leave the destination field empty
4535 USB Host
Emulated keyboard layout1 An emulated keyboard layout of the host can be associated with one video input By default this is setto native and associated will be made with the first connected input
Image 4-20Encoder settings USB Host
2 Press Apply to save settings
K5903129 NGS-D320 29092016 37
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
454 Decoder settings
4541 Overview
Decoder settings tab1 Select the tab Decoder Settings
Image 4-21Settings _ Decoder Settings
The Decoder Settings page allows to set up the device for decoding amp streaming media2 Press the Refresh button to ensure you have the latest device status displayed correctly before mak-
ing any changesAll available output connectors on the device will always be listed even if no active connection ispresent Configuration changes can be made at any time they will be applied when the connection islive This allows to pre-configure the device in advance
4542 Audio
Headphone Line Out1 Select Headphone or Line Out to be configured for streaming
Image 4-22Decoder settings Audio out
2 The Volume is by default set to 100 Change the slider to adjust the volume3 The Content field is set to loop through by defaultThe drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoderThe audio decoding can also be disabled
4 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
5 Press Apply to save settings
4543 DVI OutDP OutHDMI Out
Output Timing1 Select the Output Timing in the drop down box
38 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
- Standby- EDID preferred timing- One of the specific timings (listed in the drop down box)
Image 4-23Decoder settings DVI Out DP Out HDMI Out
2 The Content field is set to loop through by defaultThe drop down box will list any available video stream on the networkFor each interface type select a stream from another NGS-D320 to allow playback on the output portof the decoder It is also possible to disable decodingNote that decoding will be active depending on available resources Refer to Resources page 9 formore information
3 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually type a url into the Custom url field to connect to an audio stream
4 Press Apply to save settings
4544 HDMI Audio Out
HDMI Audio Out1 The Content field is set to loop through by default
Image 4-24Decoder settings HDMI Audio Out
The drop down box will list any available audio stream on the network Select a stream from anotherNGS-D320 to allow playback on the decoder
The audio decoding can also be disabled
2 When a stream is selected the Custom url field will automatically be filled inIt is also possible to manually enter a url into the Custom url field to connect to an audio stream
3 Press Apply to save settings
K5903129 NGS-D320 29092016 39
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
4 Operation
4545 USB Peripherals
Association1 A connected keyboard and mouse can only be associated with one video output By default this is
set to auto and association will be made with first connected output
Image 4-25Decoder settings USB Peripherals
You can also force association to a video output by selecting the appropriate output in the drop downbox
2 Press Apply to save settings
40 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
5 Cleaning your device
5 CLEANING YOUR DEVICE
51 Cleaning procedureBefore cleaning1 Switch off the device
2 Remove the power cord from the device
Cleaning the device1 Clean the cabinet using a soft cleaning clothCautionDo not apply or spray liquid directly to the cabinet as excess liquid may cause damage to
internal electronics Instead apply the liquid to the cleaning cloth
2 To remove stains use a damp cloth with non-aggressive cleaning products- Do NOT use abrasive cleaning agents glass cleaner or tissue paper- Do NOT use alcoholsolvents at higher concentration gt 5- Use non-aggressive cleaning products (water or a solution of distilled water and IsoPropyl Alcohol)
3 Repeat with water only
4 Wipe dry with a dry cloth
K5903129 NGS-D320 29092016 41
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
5 Cleaning your device
42 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
6 Repackaging instructions
6 REPACKAGING INSTRUCTIONS
61 Device repackingHow to repack the NGS-D3201 Open the box and remove the upper foam
Image 6-1Repacking
2 Place the NGS-D320 in the left whole of the foam
3 You may also put the cables back at the right side
4 Place the upper foam back on top and close the box with tape
K5903129 NGS-D320 29092016 43
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
6 Repackaging instructions
44 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
7 Service activities
7 SERVICE ACTIVITIES
71 Reaching the local Barco helpdesk and online supportHow to reach1 Go to Barcorsquos website wwwbarcocom
Image 7-1Website Barco
2 Click on the drop down next to Training amp Support and select Support
3 Select A specific product click Select product and choose your product
Image 7-2Product
4 Click Go
K5903129 NGS-D320 29092016 45
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
7 Service activities
The local service contact page is displayed
Image 7-3Local service contact page
5 Click Log in (youmay first need toSign up) and the SalesForcecom page appears (httpsemeasales-forcecom)
72 Online product supportContentsThe online product support provides
bull Software amp driversbull Manuals amp documentationbull Knowledgebasebull Spare partsbull Training
Download software1 In myBarco click Select your product and choose your product
The window Product Support appears
2 Select the tab Software amp drivers and download your software
73 Reporting an issue in SalesForcecomHow to report1 Login by entering your user name and password
2 Create a new request by selecting Swappart delivery request
46 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
7 Service activities
Image 7-4Swap part delivery request
3 Fill out the service request form
Image 7-5Service request form
4 Click Submit amp Add Attachment5 Click Choose File and browse to the file to attach6 Click Attach file7 To add extra files repeat the Choose File and Attach file actionWhen all files are attached click Done
K5903129 NGS-D320 29092016 47
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
7 Service activities
Image 7-6Attach file(s)
An overview will be displayed Extra information can be added
Your service request is logged
48 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
8 Important information
8 IMPORTANT INFORMATION
81 Safety informationGeneral recommendationsRead the safety and operating instructions before operating the device
Retain safety and operating instructions for future reference
Adhere to all warnings on the device and in the operating instructions manual
Follow all instructions for operation and use
Electrical Shock or Fire HazardTo prevent electric shock or fire hazard do not remove cover
No serviceable parts inside Refer servicing to qualified personnel
Do not expose this apparatus to rain or moisture
Modifications to the unitDo not modify this equipment without authorization of the manufacturer
Type of protection (Electrical)Device with external power supply Class I equipment
Degree of safety (flammable anesthetic mixture)Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygenor nitrous oxide
Power connection ndash Equipment with external 12 VDC power supplybull Power requirements The equipment must be powered using the delivered medical approved 12 VDC
( ) power supplybull The medical approved DC ( ) power supply must be powered by the AC mains voltagebull The power supply is specified as a part of the ITE equipment or combination is specified as an ITE
systembull To avoid the risk of electric shock this equipment must only be connected to a supply mains with
protective earthbull The equipment should be installed near an easily accessible outletbull The equipment is intended for continuous operation
Transient over-voltageIf the device is not used for a long time disconnect it from the AC inlet to avoid damage by transientover-voltage
To fully disengage the power to the device please disconnect the power cord from the AC inlet
K5903129 NGS-D320 29092016 49
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
8 Important information
Power cords bull Utilize a UL-listed detachable power cord 3-wire type SJ or equivalent 18 AWG min rated 250 V
minbull Do not overload wall outlets and extension cords as this may result in fire or electric shockbull Mains lead protection (US Power cord) Power cords should be routed so that they are not likely to
be walked upon or pinched by items placed upon or against them paying particular attention to cordsat plugs and receptacles
bull The power supply cord should be replaced by the designated operator only at all timebull Use a power cord that matches the voltage of the power outlet which has been approved and complies
with the safety standard of your particular country
ConnectionsAny external connection with other peripherals must follow the requirements of IEC6090-1 2nd ed
Water and moistureNever expose the device to rain or moisture
Never use the device near water - eg near a bathtub washbasin swimming pool kitchen sink laundrytub or in a wet basement
VentilationDo not cover or block any ventilation openings in the cover of the set When installing the device in acupboard or another enclosed location heed the necessary space between the set and the sides of thecupboard
InstallationPlace the device on a flat solid and stable surface that can support the weight of at least 3 devices If youuse an unstable cart or stand the device may fall causing serious injury to a child or adult and seriousdamage to the device
This apparatus conforms toITE EquipmentUL 60950-1 2nd Edition
CANCSA C222 No 60950-1-07 (R2012) 2nd Edition
IEC 60950-12005 (2nd Edition) + Am 12009 EN 60950-12006 + A12010 + A112009 + A122011
CISPR 222008 EN 550222010 + AC2011
CISPR 32 2012 EN 550322012 + AC 2013
IEC 61000-3-22014 EN 61000-3-22014
IEC 61000-3-32013 EN 61000-3-32013
CISPR 242010 EN 550242010
CCC - GB9254-2008 GB49431-2011 YDT993ndash1998
82 Environmental informationDisposal InformationWaste Electrical and Electronic Equipment
50 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
8 Important information
This symbol on the product indicates that under the European Directive 201219EU governingwaste from electrical and electronic equipment this product must not be disposed of with other municipalwaste Please dispose of your waste equipment by handing it over to a designated collection point for therecycling of waste electrical and electronic equipment To prevent possible harm to the environment orhuman health from uncontrolled waste disposal please separate these items from other types of wasteand recycle them responsibly to promote the sustainable reuse of material resources
For more information about recycling of this product please contact your local city office or your municipalwaste disposal service
For details please visit the Barco website at httpwwwbarcocomenAboutBarcoweee
Turkey RoHS compliance
Tuumlrkiye Cumhuriyeti AEEE Youmlnetmeliğine Uygundur
[Republic of Turkey In conformity with the WEEE Regulation]
中国大陆 RoHSChinese Mainland RoHS
根据中国大陆《电器电子产品有害物质限制使用管理办法》(也称为中国大陆RoHS) 以下部分列出了Barco产品中可能包含的有毒和或有害物质的名称和含量中国大陆RoHS指令包含在中国信息产业部MCV标准ldquo电子信息产品中有毒物质的限量要求rdquo中
According to the ldquoManagement Methods for the Restriction of the Use of Hazardous Substances in Electri-cal and Electronic Productsrdquo (Also called RoHS of Chinese Mainland) the table below lists the names andcontents of toxic andor hazardous substances that Barcorsquos product may contain The RoHS of ChineseMainland is included in the MCV standard of the Ministry of Information Industry of China in the sectionldquoLimit Requirements of toxic substances in Electronic Information Productsrdquo
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
印制电路配件
Printed Circuit Assemblies
x o o o o o
外接电(线)缆External Cables
x o o o o o
散热片(器)
Heatsinks
o o o o o o
底架
Chassis
o o o o o o
电源供应器
Power Supply Unit
x o o o o o
风扇
Fan
x o o o o o
这个表被制备按照规定SJT 11364
This table is prepared in accordance with the provisions of SJT 11364
K5903129 NGS-D320 29092016 51
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
8 Important information
零件项目(名称)Component name
有毒有害物质或元素
Hazardous substances and elements铅(Pb)
汞
(Hg)镉(Cd)
六价铬(Cr6+)
多溴联苯
(PBB)多溴二苯醚(PBDE)
O表示该有毒有害物质在该部件所有均质材料中的含量均在 GBT 26572标准规定的限量要求以下
O Indicates that this hazardous substance contained in all of the homogeneous materials for this partis below the limit requirement of GBT 26572X表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 GBT 26572标准规定的限量要求
X Indicates that this hazardous substance contained in at least one of the homogeneous materialsused for this part is above the limit requirement in GBT 26572
在中国大陆销售的相应电子信息产品(EIP)都必须遵照中国大陆《电子电气产品有害物质限制使用标识要求》标准贴上环保使用期限(EFUP)标签Barco产品所采用的EFUP标签(请参阅实例徽标内部的编号使用于指定产品)基于中国大陆的《电子信息产品环保使用期限通则》标准
All Electronic Information Products (EIP) that are sold within Chinese Mainland must comply with theldquoMarking for the restriction of the use of hazardous substances in electrical and electronic productrdquo of Chi-nese Mainland marked with the Environmental Friendly Use Period (EFUP) logo The number inside theEFUP logo that Barco uses (please refer to the photo) is based on the ldquoGeneral guidelines of environ-ment-friendly use period of electronic information productsrdquo of Chinese Mainland
Image 8-1
83 Regulatory compliance informationFCC class AThis equipment has been tested and found to comply with the limits for a Class A digital device pursuantto part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment This equipment generatesuses and can radiate radio frequency energy and if not installed and used in accordance with the instruc-tion manual may cause harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will be required to correctthe interference at his own expense
Changes or modifications not expressly approved by the party responsible for compliance could void theuserrsquos authority to operate the equipment
Canadian noticeCAN ICES-3 (A)NMB-3(A)
52 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
8 Important information
84 EMC noticeEuropean Union EMC Directive Conformance StatementThis product is in conformity with the protection requirements of EU Council Directive 2004108EC on theapproximation of the laws of the Member States relating to electromagnetic compatibility
Barco cannot accept responsibility for any failure to satisfy the protection requirements resulting from anonrecommended modification of the product
This product has been tested and found to comply with the limits for Class A Information TechnologyEquipment according to CISPR 22European Standard EN 55022 The limits for Class A equipment werederived for commercial and industrial environments to provide reasonable protection against interferencewith licensed communication equipment
WARNING This equipment is compliant with Class A of CISPR 32 In a residential en-vironment this equipment may cause radio interference
85 Explanation of symbolsSymbols on the deviceOn the device or power supply you may find the following symbols (nonrestrictive list)
Indicates the device meets the requirements of the applicable EC directives
Indicates compliance with Part 15 of the FCC rules (Class A or Class B)
Indicates the device is approved according to the UL Recognition regulations
Indicates the device is approved according to the UL regulations for Canadaand US
Indicates the device is approved according to the UL Demko regulations
Indicates the device is approved according to the CCC regulations
Indicates the device is approved according to the VCCI regulations
Indicates the device is approved according to the KC regulations
K5903129 NGS-D320 29092016 53
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
8 Important information
Indicates the device is approved according to the BSMI regulations
Indicates the device is approved according to the PSE regulations
Indicates the device is approved according to the BIS regulations
Indicates the device is approved according to the RCM mark (regulatorycompliance mark) for Australia and New-Sealand
Indicates the USB connectors on the device
Indicates the DisplayPort connectors on the device
Indicates the legal manufacturer
Indicates the manufacturing date
Indicates the temperature limitations4 for the device to safely operate within specs
Indicates the device serial number
Indicates the device part number or catalogue number
Warning dangerous voltage
Caution
Consult the operating instructions
4 Values for xx and yy can be found in the technical specifications paragraph
54 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
8 Important information
Indicates this device must not be thrown in the trash but must be recycledaccording to the European WEEE (Waste Electrical and Electronic Equipment)directive
Indicates Direct Current (DC)
Indicates Alternating Current (AC)
Stand-by
Equipotentiality
or
Protective earth (ground)
86 Legal disclaimerDisclaimer noticeAlthough every attempt has been made to achieve technical accuracy in this document we assume noresponsibility for errors that may be found Our goal is to provide you with the most accurate and usabledocumentation possible if you discover errors please let us know
Barco software products are the property of Barco They are distributed under copyright by Barco NV orBarco Inc for use only under the specific terms of a software license agreement between Barco NV orBarco Inc and the licensee No other use duplication or disclosure of a Barco software product in anyform is authorized
The specifications of Barco products are subject to change without notice
TrademarksAll trademarks and registered trademarks are property of their respective owners
Copyright noticeThis document is copyrighted All rights are reserved Neither this document nor any part of it maybe reproduced or copied in any form or by any means - graphical electronic or mechanical includingphotocopying taping or information storage and retrieval systems - without written permission of Barco
copy 2016 Barco NV all rights reserved
87 Technical Specifications NGS-D320 LiteNGS-D320 LiteImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)
K5903129 NGS-D320 29092016 55
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
8 Important information
Remote keyboard andmouse
Supported (Native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSP DNS NTPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels 1Number of streams 1Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio 16bit 48kHz stereoCodec Video H264 HighMainBase Profile up to level 50
- 60fps up to 1920x1200 (1x)
- 30fps up to 2560x1600 (1x)
- 15fps up to 4096x2160 (1x)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressedLatency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)
56 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
8 Important information
Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
88 Technical Specifications NGS-D320 ProNGS-D320 ProImage processing Color space conversion scaling frame rate reductionAutomatic downscaling Y (Adjust to profile)Remote keyboard andmouse
Supported (native keymap)
Safety UL cUL EN IEC 60950-1 CB reportEMC CE FCC Part 15 Class A CISPR 22 ICES003Dimensions 44 mm H x 170 mm W x 170 mm D (173rdquo H x 67rdquo W x 67rdquo)Weight 1 plusmn 001 kg (220 lbs)Power Typical 35WPower Supply 12VDC 100-240VAC 60W external locking powerOperating temperature 0degC to 40degC (32degF to 104degF)Storage temperature -20degC to 70degC (-4degF to 158degF)Sound level Typical 32dBA at 20degCMounting Optional VESA adapter plate or 1U rack mount for 2 devicesStandalone HTTPS Web interfaceFirmware upgrade HTTPS Web interface USB Storage DeviceEthernet 1GbE full duplexIP addressing DHCP link local fixed IPProtocols Unicast Multicast (IGMP v3) RTP RTSPRTSP Sessions Multicast maximum 12 simultaneous RTSP session per channel
Unicast maximum 2 simultaneous RTSP session per channelDiscovery Zeroconf SAP (RFC 2974)Number of channels Up to 2Number of streams Up to 2Graphics 640x480 - 2560x1600 24-60Hz
640x480 - 4096x2160 24-30HzAudio uncompressedCodec Video H264 HighMainBase Profile up to level 51
- 60fps up to 1920x1200 (2x)
- 30fps up to 2560x1600 (2x)
- 60fps up to 2560x1600 (1x)
- 30fps up to 4096x2160 (1x) (version 21 or higher)Bandwidth Video 384 kbps ndash 12 Mbps
Audio uncompressed
K5903129 NGS-D320 29092016 57
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
8 Important information
Latency encoder-decoderend-to-end
80-200ms (typical 100ms)
Boot time 15sVideo 1 Dual Link DVI amp 1 DisplayPort 11a amp 1 HDMI 14 input
1 Dual Link DVI amp 1 DisplayPort 12 amp 1 HDMI 14 output
Flexible Loop ThroughAudio 1 35mm jack stereo line level in amp line out
1 35mm jack mono mic in amp stereo headphones outUSB 3 Type A connectors 1 Micro-B connectorNetwork 1 SFP (1Gb copper)Dimensions packaged 382mmx273mmx85mm | 1504x1075x335Weight packaged 22 kg | 48 lbs
89 Open source license informationOpen source license informationThis product contains software components released under an Open Source license You acknowledgeliving up to the conditions of each separate Open Source Software license
A list of the Open Source Software components used is available in the applicable EULA through the ldquoMyBarcordquo section of the Barco website or through other (online) means
Copyright on each Open Source Software component belongs to the respective initial copyright holdereach additional contributor andor their respective assignee(s) as may be identified in the respective OpenSource Software documentation source code README file or otherwise You shall not remove or ob-scure or otherwise alter the respective copyrights
EACH SEPARATE OPEN SOURCE SOFTWARE COMPONENT AND ANY RELATED DOCUMENTA-TION ARE PROVIDED AS IS WITHOUT EXPRESS OR IMPLIED WARRANTY INCLUDING BUT NOTLIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU-LAR PURPOSE IN NO EVENT SHALL THE COPYRIGHTHOLDER OR ANY OTHER CONTRIBUTORBE LIABLE FOR DIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGESEVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES HOWEVER CAUSED AND ON ANYTHEORY OF LIABILITY MORE INFORMATIONDETAILS IS TO BE FOUND IN EACH SPECIFIC OPENSOURCE LICENSE
With respect to GPL LGPL or similar licenses with regard to corresponding source code access andautomatic license terms applicability
bull You acknowledge living up to the conditions of each such specific applicable Open Source Softwarelicense You are responsible for your own additions changes or modifications without any recourseor claim towards Barco whatsoever You further acknowledge that any such additions changes ormodifications may impair the ability of Barco ndash at Barcorsquos sole discretion - to continue to provide ser-vice warranties software updates fixes maintenance access or such similar abilities without anyrecourse or claim towards Barco whatsoever
bull Barco offers to provide the corresponding source code and shall make the corresponding source codeavailable to you via email or download link except where the applicable license entitles you to requireBarco to provide you the corresponding source code on a tangible medium in which case Barco willcharge you for the actual costs of performing such distribution such as the cost of media shippingand handling You may exercise this option upon written request to Barco NV attn legal departmentPresident Kennedypark 35 8500 Kortrijk (Belgium) This offer is valid for a period of three (3) yearsfrom the date of the distribution of this product by Barco
58 K5903129 NGS-D320 29092016
Recommended