View
0
Download
0
Category
Preview:
Citation preview
Power. Speed. Accuracy. Simplicity.PieceMaker
MULTINAIL .COM DAHLSENS TRANSIT ION TO MULTINAIL 3
The latest evolution in saw technology – the PieceMakerThe PieceMaker is an Australian designed and manufactured saw that will cut, print and handle the timber you need for your truss, wall and floor manufacturing requirements. It can cut your standard and custom mitres, birdsmouths, raking plates and studs, low angles, long cuts, large timber sections and all your normal standard cutting. It’s the manufacturing centre that every truss plant needs.
Bigger. Faster. Stronger • Significantly increases productivity• Reduces downtime• Increases efficiency from cutting timber to production output
Australian• Designed and built in Australia for the Australian Market• Local support and spares
More cost effective• Elegantly designed, simpler and more cost effective to maintain• No requirement for expensive maintenance contracts
Job and Timber optimisation• Reduces waste. Cuts nogs from waste• Does Mitre cuts – saves on handling and another machine• Has a built-in ‘Designer’ cut mode (the operator can configure without waiting
for the detailer’s drawing)
Safer• The saw blade is fully enclosed offering a much safer working environment for the user• Reduces operator fatigue when comparing to traditional cutting methods
Reduces administration• Requires less administration• Easier to optimise as the saw conforms to production requirements
“The PieceMaker has effectively halved the time it takes to
produce the job. We were doing 500 – 600 pieces a day, we’re
now doing 2000, and I can easily see us doing 3000 pieces.
What would normally take a guy ½ day to prepare and cut is
now done in a couple of hours.”
Errol Olive, Cutting Supervisor,
TrussCorp
“The PieceMaker is outside of the pack in comparison to the others in the market.
Once you lose production in a plant like this, you can’t get it back. Having the guarantee
and reliability of local based service and repairs for breakdowns is very important.
With the PieceMaker, the fully enclosed blade is a major benefit as it dramatically
reduces the risk of injury.” Aaron Hillman,
General Manager, TrussCorp
“The work is getting out to the floor much faster – we’re reducing production time. Normally it’s the stuff at the end of the job that holds everything up - with the
work getting out to the floor much faster, we don’t have the guys at the table press standing around doing nothing waiting
for the timber to come through."Errol Olive,
Cutting Supervisor, TrussCorp
“The PieceMaker is so fast, with so much torque, you don’t need to put multiple stacks through it, you can put singles through and still get your output.” Warwick Porter, National Machinery Sales Manager Multinail
PieceMaker Features, Options & Technical Specifications
Specifications
Cutting heads 1
Motor size 7.5hp
Blade size 450mm
Infeed conveyor 6230mm(L) x 4060mm(W)
Outfeed conveyor 8581mm(L) x 2800mm(W)
Weight 4600kg approx.
Power requirements 63amp, 415v, 3 phase +N +E
Max. depth of cut 100mm
Min. finished length 1mm
Max. finished length 6000mm
Timber height range 35mm -100mm
Timber width range 70mm - 400mm
Min. mitre angles 15°
Min. cut angle 2°
Features • Supports all data down loads from
all the major software suppliers• Operational software simple to use
and train • Easy to calibrate
Standard Features • Dust extraction system • Includes waste conveyor• Ink jet timber printer• Full perimeter fencing
(rear of machine) • Spares kit
Options • Left or right hand feed
The outfeed system for the PieceMaker
Front view
Top view
15520mm
8607mm 1180mm 5733mm
4454
mm
746mm
2322
mm
155 Burnside RdStapylton, QLD 4207
Australia
07 3297 3250enquiry@multinail.com
multinail.com
Multinail Machinery Pty LtdABN 52 060 402 860
Recommended