View
215
Download
0
Category
Preview:
Citation preview
Features and specifications are subject to change at any time without notice.
Throughout this guide, dimensions may vary by ± 3 mm.
TA B L E O F C O N T E N T S
3 S U B - Z E R O O U T D O O R R E F R I G E R AT O R
7 W O L F O U T D O O R G R I L L S | M O D U L E S
14 W O L F O U T D O O R W A R M I N G D R A W E R
20 W A R R A N T I E S
Sub-Zero Outdoor Refrigerator Drawers
The Sub-Zero refrigerator drawers is a helpful addition to any outdoor kitchen. Compact, yet roomy, this integrated unit can be installed to fit flush with surrounding cabinetry. The outdoor model requires the use of Sub-Zero stainless steel outdoor accessory panels with pro handles to match Wolf outdoor products. These panels are available with or without a lock through an authorized Sub-Zero dealer. For local dealer information, visit our website, subzero.com.
OUTDOOR REFRIGERATOR
REFRIGERATOR DRAWERS
ICBID-24RO
subzero-wolf.com | 3
4 | subzero-wolf.com
OUTDOOR REFRIGERATOR
OPENING DIMENSIONS
654 mmOPENING
DEPTH
610 mmOPENING WIDTH
876 mmOPENINGHEIGHT
*114 mm finished returns will be visible and should be finished to match cabinetry.
SIDE VIEW
TOP VIEW
FRONT VIEW
114 mm*FINISHEDRETURN
FRAMELESS CABINETRY
114 mm*FINISHEDRETURN
FILLER
FRAMED CABINETRY
610 mm 610 mm
Refrigerator Drawers
OVERALL DIMENSIONS
610 mm
467mm
610 mm
6 mm
876 mm* 268
mm
338mm
10 mm
92 mm*864 mm MIN TO 889 mm MAX
INTERIOR CAPACITY
REFRIGERATOR DRAWERS
Model ICBID-24RO 71 L
IMPORTANT NOTE: Overall dimensions do not include panels or handles. Dimensions will vary with panel thickness. The depth of the integrated model is 610 mm. Allow for
panel thickness when planning the finished opening depth. A minimum 114 mm finished return is required on all sides of the opening. Framed cabinets will require additional finished filler material behind the face frame for a proper installation. Refer to the illustration.
subzero-wolf.com | 5
OUTDOOR REFRIGERATOR
Electrical
Installation must comply with all applicable electrical codes.
The electrical supply must be located within the shaded area shown in the illustration below. A separate circuit, ser-vicing only this appliance is required.
IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is required to reduce the risk of electrical shock.
The electrical outlet must be positioned with the grounding prong to the right of the thinner blades.
ELECTRICAL REQUIREMENTS
Electrical Supply 220–240 VAC, 50/60 Hz
Service 1 A
Receptacle 3-prong grounding-type
241mm
6 mm
108mm
114mm
FLOOR
LEFT SIDEOF OPENING
Electrical supply location.
Refrigerator Drawers
DUAL INSTALLATION
When installing two units side by side in a dual installa-tion, the opening width is the width of the two units added together. A dual installation kit will be required for this instal-lation. If a dual installation kit is not specified, a minimum 51 mm filler strip is required between units.
Dual installation kits are available through an authorized Sub-Zero dealer. For local dealer information, visit our website, subzero.com.
6 | subzero-wolf.com
Stainless Steel Panels
The outdoor model requires the use of Sub-Zero stainless steel outdoor accessory panels. These panels have pro handles to match Wolf outdoor products and are avail-able with or without a lock through an authorized Sub-Zero dealer. For local dealer information, visit our website, subzero.com.
The thickness of outdoor stainless steel panels is 38 mm. The depth of each integrated model is 610 mm. Allow for panel thickness when planning the finished opening depth.
Reveals of 3 mm are typical, however, the reveal between the upper and lower outdoor stainless steel panels is 6 mm to accommodate the lock.
OUTDOOR REFRIGERATOR
Standard Handles
Optional stainless steel pro handles are avail able through an authorized Sub-Zero dealer. Refer to the chart below for standard handle length for the refrigerator drawers.
HANDLE LENGTH
Pro Handle 495 mm
subzero-wolf.com | 7
Wolf Outdoor Grills | Modules
Taste what happens when the heritage of professional cooking moves from the kitchen to the patio. Like their indoor counterparts, Wolf outdoor grills are precision instruments. Constructed of heavy-duty stainless steel, the 76 cm, 91 cm, 107 cm and 137 cm grills have powerful burners every five inches for even heat distribution. An electric rotisserie with infrared burner produces succulent poultry and roasts. All grill models can be built-in and all except the 137 cm grill, can be used on a cart for portable convenience. The 7.3 kW burner module can be built into an outdoor kitchen and the side burner attached to a cart. Wolf grills and modules can be ordered in natural or LP gas.
OUTDOOR GRILLS | MODULES
OUTDOOR GRILLS
ICBOG30
ICBOG42
ICBOG36
ICBOG54
ICBBM13 BURNER MODULE
ICBSB13 SIDE BURNER
OUTDOOR MODULES
8 | subzero-wolf.com
273 mm
762 mm
705 mm330mm
WWIDTH
MAX DOOR/DRAWER CLEARANCE 559 mm
610 mmTO GRILL
PLATFORM
927mm
705 mm
305mm
76 mm
762 mmHOOD CLOSED
318 mmTO GRILLING
SURFACE
686mm
WWIDTH
705 mm
64mm
CLEARANCEFOR OPEN
HOOD
OUTDOOR GRILLS | MODULES
Outdoor Grills | Modules
OUTDOOR GRILL
GRILL CART
BURNER MODULE | SIDE BURNER WIDTH—OUTDOOR GRILL W
ICBOG30 762 mm
ICBOG36 914 mm
ICBOG42 1067 mm
ICBOG54 1372 mm
WIDTH—GRILL CART W
ICBCART30 762 mm
ICBCART36 914 mm
ICBCART42 1067 mm
subzero-wolf.com | 9
OUTDOOR GRILLS | MODULES
Outdoor Grills | Modules
BURNER RATING
GRILL BURNERS
ICBOG30, ICBOG36, ICBOG42, ICBBM13, ICBSB13 7.3 kWICBOG54 7.5 kW
SEAR ZONE
ICBOG36, ICBOG42 7.3 kWICBOG54 7.5 kW
ROTISSERIE
ICBOG30 4.1 kWICBOG36, ICBOG42 4.7 kWICBOG54 (2) 4.1 kW
Planning Information
For portable applications, Wolf grill carts are designed specifically to fit grill models ICBOG30, ICBOG36 and ICBOG42 and the side burner. Model ICBOG54 is designed for built-in applications only.
For built-in applications, Wolf outdoor grills and the burner module are designed for easy placement into a built-in enclosure. For outdoor grills, installation in a combustible enclosure requires an insulating liner. For the burner module, an insulating liner is not required. The enclosure should be built according to specifications for your specific installa-tion on the following pages. If the burner module is installed next to an outdoor grill, a minimum of 305 mm is required between units on the rotisserie motor side and 51 mm on the opposite side. A rotisserie side conversion kit is avail-able from an authorized Wolf dealer.
Optional stainless steel accessory doors and drawers are available for built-in applications.
Grill carts, insulating liners and stainless steel doors and drawers are avail able through an authorized Wolf dealer. For local dealer information, visit our website, wolfappliance.com.
10 | subzero-wolf.com
OUTDOOR GRILLS | MODULES
GAS SUPPLY
Installation must comply with all applicable gas codes.
A gas supply line of 19 mm rigid pipe must be provided to the outdoor grill or module. If local codes permit, a certified, .9 m long, 13 mm or 19 mm ID flexible metal appliance con-nector is recommended to connect the units ISO 7-1 female inlet to the gas supply line.
An inline regulator is installed on the unit for connecting to NAT or LP gas sources. For local dealer information, visit our website, wolfappliance.com.
GAS REQUIREMENTS
NATURAL GAS
Supply Pressure 12.5 mbarMin Line Pressure 17.5 mbarMax Regulator Pressure 100 mbar
LP GAS
Supply Pressure 25 mbarMin Line Pressure 27.4 mbarMax Regulator Pressure 100 mbar
Planning Information
ELECTRICAL
Installation must comply with all applicable electrical codes.
The electrical outlet must be located within reach of the power cord. A separate circuit, servicing only this appli-ance is required. A ground fault circuit interrupter (GFCI) is required to reduce the risk of electrical shock.
ELECTRICAL REQUIREMENTS (GRILL | MODULE)
Electrical Supply grounded, 220-240 VAC, 50/60 Hz
Service 1 A
Receptacle 3-prong grounding-type, IEC inlet
ELECTRICAL REQUIREMENTS (ROTISSERIE)
Electrical Supply—Input grounded, 220-240 VAC, 50/60 Hz
Electrical Supply—Output 12 VDC
Service 0.5 A (6 Watts)
Receptacle barrel plug, 2.1 mm ID x 5.5 mm OD
subzero-wolf.com | 11
508mm
19 mm
479mm
762 mm
727 mm
527mm
287mm
657mm
19 mm
241mm
762 mm
686 mm
527mm
483mm
A
B
19 mm
32 mm
OUTDOOR GRILLS | MODULES
Accessory Doors | Drawers
DOORS
DOOR WIDTH A B
46 cm Single 457 mm 413 mm
76 cm Double 762 mm 718 mm
91 cm Double 914 mm 870 mm
107 cm Double 1067 mm 1022 mm
137 cm Double 1372 mm 1327 mm
SINGLE DRAWER
DRAWER | DOOR UNIT
2- OR 3-DRAWER UNIT
527mm
508mm
19 mm
483mm
330 mm
305 mm
12 | subzero-wolf.com
298mm
OPENINGHEIGHT
DOORS / DRAWERSOPENING WIDTH
616 mmOPENING
DEPTH
OPENINGHEIGHT
152mm
25 mm min
GRILLOPENING
21mm
COUNTERTOP OVERHANG
GRILLOVERLAP
FRONT VIEW
TOP VIEW
WOPENING WIDTH
NOTE: Shaded area above countertop indicates minimum clearance tocombustible surfaces, combustible materials cannot be located within this area.
64 mm
330mm
89mm
G
102 mm
152mm
G
321mm
OPENINGHEIGHT
DOORS / DRAWERSOPENING WIDTH
660 mmOPENING
DEPTH
OPENINGHEIGHT
305mm
25 mm min
273mm
127mm
CL
CL
70 mmKNOCKOUT
LINEROPENING
21mm
COUNTERTOP OVERHANG
LINEROVERLAP
FRONT VIEW
TOP VIEW
WOPENING WIDTH
NOTE: Shaded area above countertop indicates minimum clearance tocombustible surfaces, combustible materials cannot be located within this area.
305 mm
G
OUTDOOR GRILLS | MODULES
OPENING WIDTH—NON-COMBUSTIBLE W
ICBOG30 724 mm
ICBOG36 876 mm
ICBOG42 1029 mm
ICBOG54 1334 mm
Outdoor Grills
NON-COMBUSTIBLE INSTALLATION COMBUSTIBLE INSTALLATION
OPENING WIDTH—COMBUSTIBLE W
ICBOG30 851 mm
ICBOG36 1003 mm
ICBOG42 1156 mm
ICBOG54 1461 mm
subzero-wolf.com | 13
OUTDOOR GRILLS | MODULES
254 mmOPENINGHEIGHT
616 mmOPENING
DEPTH
152mm
MODULEOPENING
14mm
COUNTERTOP OVERHANG
MODULEOVERLAP
FRONT VIEW
TOP VIEW
305 mmOPENING
NOTE: Shaded area above countertop indicates minimum clearance tocombustible surfaces, combustible materials cannot be located within this area.An insulating liner is not required.
G
203mm
178mm
G
76 mm
305 mm
Burner Module
INSTALLATION
Outdoor Grills
ACCESSORY DOORS | DRAWERS
OPENING—DOORS W H
46 cm Single 413 mm 483 mm
76 cm Double 718 mm 483 mm
91 cm Double 870 mm 483 mm
107 cm Double 1022 mm 483 mm
137 cm Double 1327 mm 483 mm
OPENING—DRAWERS W H
Single Drawer 692 mm 248 mm
2- or 3-Drawer Unit 308 mm 483 mm
Drawer | Door Unit 743 mm 483 mm
Wolf Outdoor Warming Drawer
Wolf warming drawers are designed to take care of prepared foods until it’s time to serve them. You can adjust the tem-perature, keeping moist foods moist and crisp foods crisp. Warming drawers are ideal for proofing dough. They can also be used to warm robes and towels. The stainless steel drawer front features a pro handle. The integrated drawer front allows for a custom wood panel and handle. Model ICBWWD30O, approved for outdoor installations, is ideal for any outdoor kitchen.
OUTDOOR WARMING DRAWER
14 | subzero-wolf.com
PROFESSIONAL
CUSTOM PANEL
WARMING DRAWER FRONTS
STAINLESS STEEL
INTEGRATED
subzero-wolf.com | 15
A
BWWIDTH
OPEN DRAWER
578 mm
718 mm
229mm
264mm
546mm
DIMENSIONS
OUTDOOR WARMING DRAWER
Warming Drawer
DRAWER FRONT OPTIONS
Wolf warming drawer fronts allow for many design options, but the warming drawer itself will be the same for all appli-cations. A panel mounting kit is required when installing a custom panel. The panel mounting kit is available through an authorized Wolf dealer. For local dealer information, visit the find a showroom section of our website, wolfappliance.com.
The 51 mm thick drawer front, in 76 cm and 91 cm widths, is designed to be installed below an outdoor grill, so the panel aligns properly with the front of the grill. Dimensions for the warming drawer remain the same, even though the drawer front may be wider to match a Wolf 91 cm outdoor grill.
STAINLESS STEEL DRAWER FRONT
WIDTH W
76 cm Drawer Front 759 mm91 cm Drawer Front 911 mm
DEPTH A B
Professional 29 mm 89 mmProfessional (51 mm thick) 54 mm 114 mm
INTEGRATED DRAWER FRONT
CUSTOM PANEL W H D
Dimensions (typical) 759 mm 264 mm 19 mmMin Thickness 16 mm
16 | subzero-wolf.com
OUTDOOR WARMING DRAWER
Planning Information
The warming drawer must be installed with a Wolf drawer front, avail able through an authorized Wolf dealer. For local dealer information, visit our website, wolfappliance.com. Specific installation instructions are included with the drawer front.
The warming drawer can be installed in a standard or flush inset application.
For a standard installation, the drawer collar and front panel sit proud of the cabinet face frame. A recessed installation requires the cabinetry be recessed by 5 mm so the collar is flush with the cabinet face frame but the drawer front will sit proud. A flush inset installation requires the drawer collar and front panel be recessed to be flush with surrounding cabinetry. Refer to illustrations on the following pages for minimum cabinet dimensions for your specific installation.
Finish the edges of the opening. They may be visible when the drawer is open.
For standard installations, face trim will overlap stiles and rails. Refer to the chart below.
For flush inset installations, a minimum 3 mm reveal is required on all sides. To ensure consistent reveals, each corner of the opening must be exactly 90°.
Model ICBWWD30O is approved for outdoor installations.
INSTALLATION REQUIREMENTS
Min Base Support 90 kg
Trim Overlap (top, bottom, sides) 16 mm
ELECTRICAL
Installation must comply with all applicable electrical codes.
Locate the electrical supply flush with the back wall and within the shaded area shown in the illustrations on the following pages. For ease of installation, the electrical supply for the warming drawer can be placed in an adjacent cabinet within reach of the power cord.
IMPORTANT NOTE: When installed outdoors, a ground fault circuit interrupter (GFCI) is required to reduce the risk of electrical shock.
ELECTRICAL REQUIREMENTS
Electrical Supply 220–240 VAC; 50/60 Hz
Service 850 W
Receptacle 3-prong grounding-type
Power Cord .9 m
subzero-wolf.com | 17
OUTDOOR WARMING DRAWER
Warming Drawer
STANDARD INSTALLATION
FRONT VIEWSIDE VIEW
TOP VIEW
NOTE: Location of electrical supply within opening may require additional cabinet depth.
584 mmOPENING
DEPTH
E
727 mmOPENING WIDTH
232 mmOPENINGHEIGHT
ANTI-TIP BLOCK
18 | subzero-wolf.com
FRONT VIEWSIDE VIEW
TOP VIEW
*Will be visible and should be finished to match cabinetry.**Dimension provides minimum reveals.
NOTE: Location of electrical supply within opening may require additional cabinet depth.
610 mmFLUSH INSET
DEPTH
ADRAWERFRONTDEPTH
270 mmFLUSHINSET
HEIGHT**
765 mmFLUSH INSET WIDTH**
19 mm
19 mm
19 mm E
E
FINISHEDCLEATS*
ANTI-TIP BLOCK
Warming Drawer
FLUSH INSET INSTALLATION
OUTDOOR WARMING DRAWER
DRAWER FRONT DEPTH A
Professional 29 mm
Professional (51 mm thick) 54 mm
Custom front panel depth is dependent on panel thickness.
subzero-wolf.com | 19
Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowflake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf & Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design, are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries. All other trademarks are property of their respective owners in the United States and other countries.
Sub-Zero International Outdoor Limited Warranty*
FOR RESIDENTIAL USE
FULL ONE YEAR WARRANTY**
For one year from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours.
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For five years from the date of original installation, this Sub-Zero product warranty covers all parts and labor to repair or replace, under normal residential use, these parts that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided by Sub-Zero under the above warranty must be performed by Sub-Zero factory certified service, unless otherwise specified by Sub-Zero, Inc. Service will be provided during normal business hours.
TERMS APPLICABLE TO EACH WARRANTY
The warranty applies only to products installed for normal residential use. This warranty does not cover any parts or labor to correct any defect caused by negligence, accident or improper use, maintenance, installation, service or repair.
For more information regarding your Sub-Zero product warranty, contact your dealer. Warranties must comply to all country, state, city, local and or ordinance.
*Product must be approved for outdoor use, designated by model and serial number.
**Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited 60-day parts and labor warranty for cosmetic defects.
**Replacement water filters are not covered by the product warranty.
Wolf Appliance International Outdoor Limited Warranty*
FOR RESIDENTIAL USE
FULL ONE YEAR WARRANTY**
For one year from the date of original installation, this Wolf Appliance product warranty covers all parts and labor to repair or replace, under normal residential use, any part of the product that proves to be defective in materials or workmanship. All service provided by Wolf Appliance under the above warranty must be performed by Wolf factory certified service, unless otherwise specified by Wolf Appliance, Inc. Service will be provided during normal business hours.
LIMITED FIVE YEAR WARRANTY
For five years from the date of original installation, Wolf Appliance will repair or replace the following parts that prove to be defective in materials or workmanship: stainless steel briquette trays, gas valves, drip pans, electronic control boards and electric heating elements. If the owner uses Wolf factory certified service, the service provider will repair or replace these parts with the owner paying for all other costs, including labor. If the owner uses non-certified service, the owner must contact Wolf Appliance, Inc. (using the information below) to receive repaired or replacement parts. Wolf Appliance will not reimburse the owner for parts purchased from non-certified service or other sources.
For more information regarding your Wolf product warranty, contact your authorized Wolf dealer. Warran-ties must comply to all country, state, city, local and or ordinance.
*Product must be approved for outdoor use, designated by model and serial number.
**Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited 60-day parts and labor warranty for cosmetic defects.
Recommended