OD-7201 OD-7201 · 2019-12-17 · SPECIFICATION CONSTRUCTION: Fixture is manufactured in compliance...

SPECIFICATION CONSTRUCTION: Fixture is manufactured in compliance with IEC 60598-1 and tested by UL-Demko laboratory in Denmark. Electrical protection class 1. IP54 BODY: Head components in corrosion resistant high-pressure die- cast aluminium ADC12 alloy. This luminaire is to be used with extruded aluminium pole 105mm. Pole and ground installation unit are available seperately - please see detail on page 394,398,399. Special pole-entry on the luminaire for other pole size can be made upon request. OPTIC COVER: Self-extinguishing high impact resistant clear+prismatic polycarbonate diffuser. with UV stabilized additive. Material from Bayer - Germany or Teijin - Japan. REFLECTOR: Corrosion resistant powder coated aluminium plate. GLARE SHIELD: High purity anodised slanted aluminium ring louver. PROTECTION: Weather proof and durable silicone gasket. Service temperature -40 to +200 C. FASTENING: All external screw is in 316 stainless steel with silicone grease dipping. CABLE ENTRY: Prepare for H07RN-F cable 3G x1.0 with pull relife device. LAMP HOLDER: E27 ceramic nickle-coated contact from Vossloh Schwabe - Germany / ENEC approved. For discharge/tungsten halogen lamp. T270 rating 4/250/5kV. Gx24q-4 holder in PBT phosphor bronze contact from AAG Stucchi - Italy / ENEC approved. For compact fluorescent lamp. T140 rating 2A-250V.CONTROL GEAR: Magnetic ballast from Vossloh Schwabe - Germany / ENEC approved. 230V 50Hz tw130. For discharge lamp. High frequency electronic ballast from Vossloh Schwabe - Germany / ENEC approved. 220-240V 0-50-60Hz tc70 A2 EEI class. For 4 pins compact fluorescent lamp. Electronic superimposed ignitor with automatic switch-off feature from Vossloh Schwabe - Germany / ENEC approved. Ignition voltage 4-5kV 220-240V 50-60Hz. For ceramic/quartz discharge lamp. Power factor correction for discharge lamp from Vossloh Schwabe - Germany or from Electronicon - Germany. ENEC approved.WIRING: 1x0.75 tinned copper silicone rubber insulated cable from CET Eletric - Italy / IMQ approved. 2kV / -60 to +180 C service temperature. Double silicone insulation ignition wire. Tinned copper condutor. Impulsive voltage 5kV. Connector in PA6.6 nickle-plated brass insert. 600V/24A. -40 to +130 C service temperature. Cross section 6mm. VDE approved. Wiring provided with earth connection.PAINTING: First Stage: Chromatization treatment, resistant to corrosive and extreme environment. Second Stage: Coated with UV stabilized polyester powder in automatic chamber. Third Stage: Baked in digital temperature control room at 200 C for 30 minutes.

AVAILABLE COLOR: Black - RAL9005 (replace last 2 digits on ordering code with 01) Graphite - RAL7016 (replace last 2 digits on ordering code with 02) Dark Grey - RAL7037 (replace last 2 digits on ordering code with 03) Aluminium Silver - RAL9006 (replace last 2 digits on ordering code with 04) White - RAL9010 (replace last 2 digits on ordering code with 06)

276

IP54 F

2

OD-7201 OD-7201

Symmertical Light Distribution Post-top Luminaire

0

105

685

240

580

1000

277

METAL HALIDE Ordering Code: 7201-0-3-711-XXHIE-CE E27 70W (5900 lm)

HIGH PRESSURE SODIUMOrdering Code: 7201-0-3-611-XXHSE-I E27 70W (6000 lm)

MERCURY VAPOUROrdering Code: 7201-0-3-511-XXHME E27 80W (4000 lm)

COMPACT FLUORESCENTOrdering code: 7201-0-3-436-XXTC-TEL Gx24q-4 42W (3200 lm)

30

92 cd/KIm

7201-0-3-711-XX

30

92 cd/KIm

7201-0-3-611-XX

30

104 cd/KIm

7201-0-3-511-XX

30

86 cd/KIm

7201-0-3-436-XX

SPECIFICATION CONSTRUCTION: Fixture is manufactured in compliance with IEC 60598-1 and tested by UL-Demko laboratory in Denmark. Electrical protection class 1. IP54 BODY: Head components in corrosion resistant high-pressure die- cast aluminium ADC12 alloy. This luminaire is to be used with extruded aluminium pole 105mm. Pole and ground installation unit are available seperately - please see detail on page 394,398,399. Special pole-entry on the luminaire for other pole size can be made upon request. OPTIC COVER: Weather proof and High heat resistant PMMA clear/opal diffuser tube from Italy. High mechanical strength, surface hardness and abrasive resistant. REFLECTOR: Corrosion resistant powder coated aluminium plate. GLARE SHIELD: High purity anodised slanted aluminium ring louver (for OD-7202). PROTECTION: Weather proof and durable silicone gasket. Service temperature -40 to +200 C. FASTENING: All external screw is in 316 stainless steel with silicone grease dipping. CABLE ENTRY: Prepare for H07RN-F cable 3G x1.0 with pull relife device. LAMP HOLDER: E27 ceramic nickle-coated contact from Vossloh Schwabe - Germany / ENEC approved. For discharge / tungsten halogen lamp. T270 rating 4/250/5kV. Gx24q-4 holder in PBT phosphor bronze contact from AAG Stucchi - Italy / ENEC approved. For compact fluorescent lamp. T140 rating 2A-250V.CONTROL GEAR: Magnetic ballast from Vossloh Schwabe - Germany / ENEC approved. 230V 50Hz tw130. For discharge lamp. High frequency electronic ballast from Vossloh Schwabe - Germany / ENEC approved. 220-240V 0-50-60Hz tc70 A2 EEI class. For 4 pins compact fluorescent lamp. Electronic superimposed ignitor with automatic switch-off feature from Vossloh Schwabe - Germany / ENEC approved. Ignition voltage 4-5kV 220-240V 50-60Hz. For ceramic/quartz discharge lamp. Power factor correction for discharge lamp from Vossloh Schwabe - Germany or from Electronicon - Germany. ENEC approved.WIRING: 1x0.75 tinned copper silicone rubber insulated cable from CET Eletric - Italy / IMQ approved. 2kV / -60 to +180 C service temperature. Double silicone insulation ignition wire. Tinned copper condutor. Impulsive voltage 5kV. Connector in PA6.6 nickle-plated brass insert. 600V/24A. -40 to +130 C service temperature. Cross section 6mm. VDE approved. Wiring provided with earth connection.PAINTING: First Stage: Chromatization treatment, resistant to corrosive and extreme environment. Second Stage: Coated with UV stabilized polyester powder in automatic chamber. Third Stage: Baked in digital temperature control room at 200 C for 30 minutes.

AVAILABLE COLOR: Black - RAL9005 (replace last 2 digits on ordering code with 01) Graphite - RAL7016 (replace last 2 digits on ordering code with 02) Dark Grey - RAL7037 (replace last 2 digits on ordering code with 03) Aluminium Silver - RAL9006 (replace last 2 digits on ordering code with 04) White - RAL9010 (replace last 2 digits on ordering code with 06)

278

IP54 F

2

OD-7202 / OD-7214 OD-7202 / OD-7214

Symmertical Light Distribution Post-top Luminaire

0

OD-7214OD-7214

OD-7202 OD-7202

279

METAL HALIDEOrdering Code: 7202-0-3-711-XX7214-0-3-711-XXHIE-CE E27 70W (5900 lm)

HIGH PRESSURE SODIUM Ordering Code: 7202-0-3-611-XX7214-0-3-611-XXHSE-I E27 70W (6000 lm)

MERCURY VAPOUROrdering Code: 7202-0-3-511-XX7214-0-3-511-XXHME E27 80W (4000 lm)

COMPACT FLUORESCENTOrdering code: 7202-0-3-436-XX7214-0-3-436-XXTC-TEL Gx24q-4 42W (3200 lm)

30

95 cd/KIm

7202-0-3-711-XX

30

98 cd/KIm

7202-0-3-611-XX

30

98 cd/KIm

7202-0-3-511-XX

30

86 cd/KIm

7202-0-3-436-XX

105

700

240775

1000

3500

SPECIFICATION CONSTRUCTION: Fixture is manufactured in compliance with IEC 60598-1 Electrical protection class 1. IP54 BODY: Head components in corrosion resistant cast and spun aluminium. This luminaire is to be used with extruded aluminium pole 105mm. Pole and ground installation unit are available seperately - please see detail on page 394, 398,399. Special pole-entry on the luminaire for other pole size can be made upon request. OPTIC COVER: UV stabilized high heat resistant clear+prismatic PMMA diffuser Material from Mitsubishi - Japan. REFLECTOR: High purity anodised aluminium plate at top. GLARE SHIELD: Sandblast anodised slanted aluminium ring louver. FASTENING: All external screw is in 316 stainless steel with silicone grease dipping. CABLE ENTRY: Prepare for H07RN-F cable 3G x1.0 with pull relife device. LAMP HOLDER: E27 ceramic nickle-coated contact from Vossloh Schwabe - Germany / ENEC approved. For discharge/tungsten halogen lamp. T270 rating 4/250/5kV. Gx24q-4 holder in PBT phosphor bronze contact from AAG Stucchi - Italy / ENEC approved. For compact fluorescent lamp. T140 rating 2A-250V.CONTROL GEAR: Magnetic ballast from Vossloh Schwabe - Germany / ENEC approved. 230V 50Hz tw130. For discharge lamp. High frequency electronic ballast from Vossloh Schwabe - Germany / ENEC approved. 220-240V 0-50-60Hz tc70 A2 EEI class. For 4 pins compact fluorescent lamp. Electronic superimposed ignitor with automatic switch-off feature from Vossloh Schwabe - Germany / ENEC approved. Ignition voltage 4-5kV 220-240V 50-60Hz. For ceramic/quartz discharge lamp. Power factor correction for discharge lamp from Vossloh Schwabe - Germany or from Electronicon - Germany. ENEC approved.WIRING: 1x0.75 tinned copper silicone rubber insulated cable from CET Eletric - Italy / IMQ approved. 2kV / -60 to +180 C service temperature. Double silicone insulation ignition wire. Tinned copper condutor. Impulsive voltage 5kV. Connector in PA6.6 nickle-plated brass insert. 600V/24A. - 40 to +130 C service temperature. Cross section 6mm. VDE approved. Wiring provided with earth connection.PAINTING: First Stage: Chromatization treatment, resistant to corrosive and extreme environment. Second Stage: Coated with UV stabilized polyester powder in automatic chamber. Third Stage: Baked in digital temperature control room at 200 C for 30 minutes.

AVAILABLE COLOR: Black - RAL9005 (replace last 2 digits on ordering code with 01) Graphite - RAL7016 (replace last 2 digits on ordering code with 02) Dark Grey - RAL7037 (replace last 2 digits on ordering code with 03) Aluminium Silver - RAL9006 (replace last 2 digits on ordering code with 04) White - RAL9010 (replace last 2 digits on ordering code with 06)

280

IP54 F

2

OD-7203 OD-7203

Symmertical Symmertical Light Distribution Post-top Luminaire

0

105

380

640

1000

3500

281

METAL HALIDEOrdering Code: 7203-0-3-711-XXHIE-CE E27 70W (5900 lm)

HIGH PRESSURE SODIUMOrdering Code: 7203-0-3-611-XXHSE-I E27 70W (6000 lm)

MERCURY VAPOUROrdering Code: 7203-0-3-611-XXHME E27 80W (4000 lm)

MERCURY VAPOUROrdering Code: 7203-0-3-512-XXHME E27 125W (6500 lm)

COMPACT FLUORESCENTOrdering code: 7203-0-3-436-XXTC-TEL Gx24q-4 42W (3200 lm)

30

99 cd/KIm

7203-0-3-711-XX

30

100 cd/KIm

7203-0-3-611-XX

30

98 cd/KIm

7203-0-3-512-XX

30

93 cd/KIm

7203-0-3-436-XX

SPECIFICATION CONSTRUCTION: Fixture is manufactured in compliance with IEC 60598-1 Electrical protection class 1. IP54 BODY: Head components in corrosion resistant cast and spun aluminium. This luminaire is to be used with extruded aluminium pole 105mm. Pole and ground installation unit are available seperately - please see detail on page 394, 398,399. Special pole-entry on the luminaire for other pole size can be made upon request. OPTIC COVER: UV stabilized high heat resistant clear+prismatic PMMA diffuser Material from Mitsubishi - Japan. REFLECTOR: High purity anodised aluminium plate at top. GLARE SHIELD: Blown opal glass for glare suppression. FASTENING: All external screw is in 316 stainless steel with silicone grease dipping. CABLE ENTRY: Prepare for H07RN-F cable 3G x1.0 with pull relife device. LAMP HOLDER: E27 ceramic nickle-coated contact from Vossloh Schwabe - Germany / ENEC approved. For discharge/tungsten halogen lamp. T270 rating 4/250/5kV. Gx24q-4 holder in PBT phosphor bronze contact from AAG Stucchi - Italy / ENEC approved. For compact fluorescent lamp. T140 rating 2A-250V.CONTROL GEAR: Magnetic ballast from Vossloh Schwabe - Germany / ENEC approved. 230V 50Hz tw130. For discharge lamp. High frequency electronic ballast from Vossloh Schwabe - Germany / ENEC approved. 220-240V 0-50-60Hz tc70 A2 EEI class. For 4 pins compact fluorescent lamp. Electronic superimposed ignitor with automatic switch-off feature from Vossloh Schwabe - Germany / ENEC approved. Ignition voltage 4-5kV 220-240V 50-60Hz. For ceramic/quartz discharge lamp. Power factor correction for discharge lamp from Vossloh Schwabe - Germany or from Electronicon - Germany. ENEC approved.WIRING: 1x0.75 tinned copper silicone rubber insulated cable from CET Eletric - Italy / IMQ approved. 2kV / -60 to +180 C service temperature. Double silicone insulation ignition wire. Tinned copper condutor. Impulsive voltage 5kV. Connector in PA6.6 nickle-plated brass insert. 600V/24A. - 40 to +130 C service temperature. Cross section 6mm. VDE approved. Wiring provided with earth connection.PAINTING: First Stage: Chromatization treatment, resistant to corrosive and extreme environment. Second Stage: Coated with UV stabilized polyester powder in automatic chamber. Third Stage: Baked in digital temperature control room at 200 C for 30 minutes.

AVAILABLE COLOR:Black - RAL9005 (replace last 2 digits on ordering code with 01) Graphite - RAL7016 (replace last 2 digits on ordering code with 02) Dark Grey - RAL7037 (replace last 2 digits on ordering code with 03) Aluminium Silver - RAL9006 (replace last 2 digits on ordering code with 04) White - RAL9010 (replace last 2 digits on ordering code with 06)

282

IP54 F

2

OD-7204 OD-7204

Symmertical Light Distribution Post-top Luminaire

0

105

640

1000

3500

380

283

METAL HALIDEOrdering Code: 7204-0-3-711-XXHIE-CE E27 70W (5900 lm)

HIGH PRESSURE SODIUMOrdering Code: 7204-0-3-611-XXHSE-I E27 70W (6000 lm)

MERCURY VAPOUR Ordering Code: 7204-0-3-511-XXHME E27 80W (4000 lm)

MERCURY VAPOUR Ordering Code: 7204-0-3-512-XXHME E27 125W (6500 lm)

COMPACT FLUORESCENT Ordering code: 7204-0-3-436-XXTC-TEL Gx24q-4 42W (3200 lm)

60

145 cd/KIm

7204-0-3-711-XX

60

125 cd/KIm

7204-0-3-611-XX

60

119 cd/KIm

7204-0-3-512-XX

60

104 cd/KIm

7204-0-3-436-XX

SPECIFICATION CONSTRUCTION: Fixture is manufactured in compliance with IEC 60598-1 Electrical protection class 1. IP54 BODY: Head components in corrosion resistant cast and spun aluminium. This luminaire is to be used with extruded aluminium pole 105mm. Pole and ground installation unit are available seperately - please see detail on page 394, 398,399. Special pole-entry on the luminaire for other pole size can be made upon request. OPTIC COVER: UV stabilized high heat resistant clear+prismatic PMMA diffuser Material from Mitsubishi - Japan. REFLECTOR: High purity anodised cone-shaped aluminium reflector. FASTENING: All external screw is in 316 stainless steel with silicone grease dipping. CABLE ENTRY: Prepare for H07RN-F cable 3G x1.0 with pull relife device. LAMP HOLDER: E27 ceramic nickle-coated contact from Vossloh Schwabe - Germany / ENEC approved. For discharge/tungsten halogen lamp. T270 rating 4/250/5kV. G12 holder in ceramic nickle-coated contact from Vossloh Schwabe - Germany / ENEC approved. For discharge lamp. T270 rating 4/250/5kV.CONTROL GEAR: Magnetic ballast from Vossloh Schwabe - Germany / ENEC approved. 230V 50Hz tw130. For discharge lamp. Electronic superimposed ignitor with automatic switch-off feature from Vossloh Schwabe - Germany / ENEC approved. Ignition voltage 4-5kV 220-240V 50-60Hz. For ceramic/quartz discharge lamp. Power factor correction for discharge lamp from Vossloh Schwabe - Germany or from Electronicon - Germany. ENEC approved.WIRING: 1x0.75 tinned copper silicone rubber insulated cable from CET Eletric - Italy / IMQ approved. 2kV / -60 to +180 C service temperature. Double silicone insulation ignition wire. Tinned copper condutor. Impulsive voltage 5kV. Connector in PA6.6 nickle-plated brass insert. 600V/24A. - 40 to +130 C service temperature. Cross section 6mm. VDE approved. Wiring provided with earth connection.PAINTING: First Stage: Chromatization treatment, resistant to corrosive and extreme environment. Second Stage: Coated with UV stabilized polyester powder in automatic chamber. Third Stage: Baked in digital temperature control room at 200 C for 30 minutes.

AVAILABLE COLOR: Black - RAL9005 (replace last 2 digits on ordering code with 01) Graphite - RAL7016 (replace last 2 digits on ordering code with 02) Dark Grey - RAL7037 (replace last 2 digits on ordering code with 03) Aluminium Silver - RAL9006 (replace last 2 digits on ordering code with 04) White - RAL9010 (replace last 2 digits on ordering code with 06)

284

IP54 F

2

OD-7211 OD-7211

Semi-indirect Light Distribution Post-top Luminaire

0

105

380

640

1000

3500

285

METAL HALIDEOrdering Code: 7211-0-3-752-XXHIT-CE G1270W (6600 lm)

METAL HALIDEOrdering Code: 7211-0-3-711-XXHIE-CE E27 70W (5900 lm)

METAL HALIDEOrdering Code: 7211-0-3-713-XXHIE-CE E27 150W (13000 lm)

HIGH PRESSURE SODIUMOrdering Code: 7211-0-3-611-XXHSE-I E27 70W (6000 lm)

MERCURY VAPOUROrdering Code: 7211-0-3-511-XXHME E27 80W (4000 lm)

30

181 cd/KIm

7211-0-3-753-XX

30

145 cd/KIm

7211-0-3-713-XX

30

179 cd/KIm

7211-0-3-611-XX

286

IP54 F

OD-7215 OD-7215

Symmertical Light Distribution Post-top Luminaire

575

1000

335

105

NEW FOR 2007THIS IS PROVISION DATA ONLY.ACTUAL DIMENSION AND LOOK MAY DIFFER FROM THIS.

287

METAL HALIDEOrdering Code: 7215-0-3-711-XXHIE-CE E2770W (5900 lm)

HIGH PRESSURE SODIUMOrdering Code: 7215-0-3-611-XXHSE-I E27 70W (6000 lm)

MERCURY VAPOUROrdering Code: 7215-0-3-511-XXHME E27 80W (4000 lm)

MERCURY VAPOUROrdering Code: 7215-0-3-512-XXHME E27 125W (6500 lm)

COMPACT FLUORESCENTOrdering code: 7215-0-3-436-XXTC-TEL Gx24q-4 42W (3200 lm)

SPECIFICATIONCONSTRUCTION: Fixture is manufactured in compliance with IEC 60598-1 Electrical protection class 1. IP54 BODY: Head components in corrosion resistant cast and spun aluminium. This luminaire is to be used with extruded aluminium pole 105mm. Pole and ground installation unit are available seperately - please see detail on page 394, 398,399. Special pole-entry on the luminaire for other pole size can be made upon request. OPTIC COVER: UV stabilized high heat resistant opal PMMA diffuser Material from Mitsubishi - Japan. FASTENING: All external screw is in 316 stainless steel with silicone grease dipping. CABLE ENTRY: Prepare for H07RN-F cable 3G x1.0 with pull relife device. LAMP HOLDER: E27 ceramic nickle-coated contact from Vossloh Schwabe - Germany / ENEC approved. For discharge/tungsten halogen lamp. T270 rating 4/250/5kV. Gx24q-4 holder in PBT phosphor bronze contact from AAG Stucchi - Italy / ENEC approved. For compact fluorescent lamp. T140 rating 2A-250V. CONTROL GEAR: Magnetic ballast from Vossloh Schwabe - Germany / ENEC approved. 230V 50Hz tw130. For discharge lamp. High frequency electronic ballast from Vossloh Schwabe - Germany / ENEC approved. 220-240V 0-50-60Hz tc70 A2 EEI class. For 4 pins compact fluorescent lamp. Electronic superimposed ignitor with automatic switch-off feature from Vossloh Schwabe - Germany / ENEC approved. Ignition voltage 4-5kV 220-240V 50-60Hz. For ceramic/quartz discharge lamp. Power factor correction for discharge lamp from Vossloh Schwabe - Germany or from Electronicon - Germany. ENEC approved.WIRING: 1x0.75 tinned copper silicone rubber insulated cable from CET Eletric - Italy / IMQ approved. 2kV / -60 to +180 C service temperature. Double silicone insulation ignition wire. Tinned copper condutor. Impulsive voltage 5kV. Connector in PA6.6 nickle-plated brass insert. 600V/24A. - 40 to +130 C service temperature. Cross section 6mm. VDE approved. Wiring provided with earth connection.PAINTING: First Stage: Chromatization treatment, resistant to corrosive and extreme environment. Second Stage: Coated with UV stabilized polyester powder in automatic chamber. Third Stage: Baked in digital temperature control room at 200 C for 30 minutes.

AVAILABLE COLOR: Black - RAL9005 (replace last 2 digits on ordering code with 01) Graphite - RAL7016 (replace last 2 digits on ordering code with 02) Dark Grey - RAL7037 (replace last 2 digits on ordering code with 03) Aluminium Silver - RAL9006 (replace last 2 digits on ordering code with 04) White - RAL9010 (replace last 2 digits on ordering code with 06)

2

0

NEW FOR 2007THIS IS PROVISION DATA ONLY.ACTUAL DIMENSION AND LOOK MAY DIFFER FROM THIS.

SPECIFICATION CONSTRUCTION: Fixture is manufactured in compliance with IEC 60598-1 Electrical protection class 1. IP54 BODY: Head components in corrosion resistant high-pressure die- cast aluminium ADC12 alloy. Top cover in thick spun aluminium. This luminaire is to be used with extruded aluminium pole 105mm. Pole and ground installation unit are available seperately - please see detail on page 394, 398,399. Special pole-entry on the luminaire for other pole size can be made upon request. OPTIC COVER: UV stabilized high heat resistant prismatic / opal PMMA diffuser Material from Mitsubishi - Japan. REFLECTOR: High purity anodised aluminium plate. PROTECTION: Weather proof and durable silicone gasket. Service temperature -40 to +200 C. FASTENING: All external screw is in 316 stainless steel with silicone grease dipping. CABLE ENTRY: Prepare for H07RN-F cable 3G x1.0 with pull relife device. LAMP HOLDER: E27 ceramic nickle-coated contact from Vossloh Schwabe - Germany / ENEC approved. For discharge/tungsten halogen lamp. T270 rating 4/250/5kV. Gx24q-4 holder in PBT phosphor bronze contact from AAG Stucchi - Italy / ENEC approved. For compact fluorescent lamp. T140 rating 2A-250V.CONTROL GEAR: Magnetic ballast from Vossloh Schwabe - Germany / ENEC approved. 230V 50Hz tw130. For discharge lamp. High frequency electronic ballast from Vossloh Schwabe - Germany / ENEC approved. 220-240V 0-50-60Hz tc70 A2 EEI class. For 4 pins compact fluorescent lamp. Electronic superimposed ignitor with automatic switch-off feature from Vossloh Schwabe - Germany / ENEC approved. Ignition voltage 4-5kV 220-240V 50-60Hz. For ceramic/quartz discharge lamp. Power factor correction for discharge lamp from Vossloh Schwabe - Germany or from Electronicon - Germany. ENEC approved.WIRING: 1x0.75 tinned copper silicone rubber insulated cable from CET Eletric - Italy / IMQ approved. 2kV / -60 to +180 C service temperature. Double silicone insulation ignition wire. Tinned copper condutor. Impulsive voltage 5kV. Connector in PA6.6 nickle-plated brass insert. 600V/24A. -40 to +130 C service temperature. Cross section 6mm. VDE approved. Wiring provided with earth connection.PAINTING: First Stage: Chromatization treatment, resistant to corrosive and extreme environment. Second Stage: Coated with UV stabilized polyester powder in automatic chamber. Third Stage: Baked in digital temperature control room at 200 C for 30 minutes.

AVAILABLE COLOR: Black - RAL9005 (replace last 2 digits on ordering code with 01) Graphite - RAL7016 (replace last 2 digits on ordering code with 02) Dark Grey - RAL7037 (replace last 2 digits on ordering code with 03) Aluminium Silver - RAL9006 (replace last 2 digits on ordering code with 04) White - RAL9010 (replace last 2 digits on ordering code with 06)

288

IP54 F

2

OD-7210 / OD-7216 OD-7210 / OD-7216

Symmertical Light Distribution Post-top Luminaire

0

OD-7210OD-7210

OD-7216

289

METAL HALIDEOrdering Code: 7210-0-3-711-XX 7216-0-3-711-XX HIE-CE E27

70W (5900 lm)

METAL HALIDEOrdering Code: 7210-0-3-713-XX7216-0-3-713-XXHIE-CE E27

150W (13000 lm)

HIGH PRESSURE SODIUMOrdering Code: 7210-0-3-611-XX7216-0-3-611-XXHSE-I E27 70W (6000 lm)

HIGH PRESSURE SODIUMOrdering Code: 7210-0-3-613-XX7216-0-3-613-XXHSE E40 150W (14500 lm)

MERCURY VAPOUROrdering Code: 7210-0-3-511-XX7216-0-3-511-XXHME E27 80W (4000 lm)

MERCURY VAPOUROrdering Code: 7210-0-3-512-XX7216-0-3-512-XXHME E27 125W (6500 lm)

MERCURY VAPOUROrdering Code: 7210-0-3-513-XX7216-0-3-513-XXHME E40 250W (14000 lm)

30

166 cd/KIm

7210-0-3-713-XX

30

165 cd/KIm

7210-0-3-613-XX

30

165 cd/KIm

7210-0-3-512-XX

30

161 cd/KIm

7210-0-3-513-XX

630

105

420

3500

1000

290

IP55 F

OD-7281 / OD-7282 / OD-7281 / OD-7282 / OD-7283OD-7283

Single / Multiple Sphere Post-top Luminair

NEW FOR 2007THIS IS PROVISION DATA ONLY.ACTUAL DIMENSION AND LOOK MAY DIFFER FROM THIS.

105

1000

400 400 400

105

1000

400 400

105

1000

OD-7281 OD-7283OD-7282

291

NEW FOR 2007THIS IS PROVISION DATA ONLY.ACTUAL DIMENSION AND LOOK MAY DIFFER FROM THIS.

METAL HALIDEOrdering Code: 7281-0-3-711-XXHIE-CE E27 70W (5900 lm)

METAL HALIDEOrdering Code: 7282-0-3-711-XXHIE-CE E27 2x70W (2x5900 lm)

METAL HALIDEOrdering Code: 7283-0-3-711-XXHIE-CE E27 3x70W (3x5900 lm)

HIGH PRESSURE SODIUMOrdering Code: 7281-0-3-611-XXHSE-I E27 70W (6000 lm)

HIGH PRESSURE SODIUMOrdering Code: 7282-0-3-611-XXHSE-I E27 2x70W (2x6000 lm)

HIGH PRESSURE SODIUMOrdering Code: 7283-0-3-611-XXHSE-I E27 3x70W (3x6000 lm)

MERCURY VAPOUROrdering Code: 7281-0-3-511-XXHME E27 80W (4000 lm)

SPECIFICATION CONSTRUCTION: Fixture is manufactured in compliance with IEC 60598-1 Electrical protection class 1. IP55 BODY: Head components in corrosion resistant high-pressure die- cast aluminium ADC12 alloy. This luminaire is to be used with extruded aluminium pole 105mm. Pole and ground installation unit are available seperately - please see detail on page 394,398,399. Special pole-entry on the luminaire for other pole size can be made upon request. OPTIC COVER: Self-extinguishing high impact resistant clear polycarbonate diffuser with UV stabilized additive from Elkamet - Germany. GLARE SHIELD: High purity anodised slanted aluminium ring louver. PROTECTION: Weather proof and durable silicone gasket. Service temperature -40 to +200 C. FASTENING: All external screw is in 316 stainless steel with silicone grease dipping. CABLE ENTRY: Prepare for H07RN-F cable 3G x1.0 with pull relife device. LAMP HOLDER: E27 ceramic nickle-coated contact from Vossloh Schwabe - Germany / ENEC approved. For discharge/tungsten halogen lamp. T270 rating 4/250/5kV. Gx24q-4 holder in PBT phosphor bronze contact from AAG Stucchi - Italy / ENEC approved. For compact fluorescent lamp. T140 rating 2A-250V.CONTROL GEAR: Magnetic ballast from Vossloh Schwabe - Germany / ENEC approved. 230V 50Hz tw130. For discharge lamp. High frequency electronic ballast from Vossloh Schwabe - Germany / ENEC approved. 220-240V 0-50-60Hz tc70 A2 EEI class. For 4 pins compact fluorescent lamp. Electronic superimposed ignitor with automatic switch-off feature from sloh Schwabe - Germany / ENEC approved. Ignition voltage 4-5kV 220-240V 50-60Hz. For ceramic/quartz discharge lamp. Power factor correction for discharge lamp from Vossloh Schwabe - Germany or from Electronicon - Germany. ENEC approved.WIRING: 1x0.75 tinned copper silicone rubber insulated cable from CET Eletric - Italy / IMQ approved. 2kV / -60 to +180 C service temperature. Double silicone insulation ignition wire. Tinned copper condutor. Impulsive voltage 5kV. Connector in PA6.6 nickle-plated brass insert. 600V/24A. - 40 to +130 C service temperature. Cross section 6mm. VDE approved. Wiring provided with earth connection.PAINTING: First Stage: Chromatization treatment, resistant to corrosive and extreme environment. Second Stage: Coated with UV stabilized polyester powder in automatic chamber. Third Stage: Baked in digital temperature control room at 200 C for 30 minutes.

AVAILABLE COLOR: Black - RAL9005 (replace last 2 digits on ordering code with 01) Graphite - RAL7016 (replace last 2 digits on ordering code with 02) Dark Grey - RAL7037 (replace last 2 digits on ordering code with 03) Aluminium Silver - RAL9006 (replace last 2 digits on ordering code with 04) White - RAL9010 (replace last 2 digits on ordering code with 06)

2

0 MERCURY VAPOUROrdering Code: 7282-0-3-511-XXHME E27 2x80W (2x4000 lm)

MERCURY VAPOUROrdering Code: 7283-0-3-511-XXHME E27 3x80W (3x4000 lm)

COMPACT FLUORESCENTOrdering code: 7281-0-3-436-XXTC-TEL Gx24q-4 42W (3200 lm)

COMPACT FLUORESCENTOrdering code: 7282-0-3-436-XXTC-TEL Gx24q-4 2x42W (2x3200 lm)

COMPACT FLUORESCENTOrdering code: 7283-0-3-436-XXTC-TEL Gx24q-4 3x42W (3x3200 lm)

292

IP55 F

OD-7285 / OD-7286 / OD-7285 / OD-7286 / OD-7287 OD-7287

Single / Multiple Sphere Post-top Luminaire

NEW FOR 2007THIS IS PROVISION DATA ONLY.ACTUAL DIMENSION AND LOOK MAY DIFFER FROM THIS.

105

1000

400 400 400

105

1000

400 400

105

1000

OD-7285 OD-7287OD-7286

293

NEW FOR 2007THIS IS PROVISION DATA ONLY.ACTUAL DIMENSION AND LOOK MAY DIFFER FROM THIS.

METAL HALIDEOrdering Code: 7285-0-3-711-XXHIE-CE E27 70W (5900 lm)

METAL HALIDEOrdering Code: 7286-0-3-711-XXHIE-CE E27 2x70W (2x5900 lm)

METAL HALIDEOrdering Code: 7287-0-3-711-XXHIE-CE E27 3x70W (3x5900 lm)

HIGH PRESSURE SODIUMOrdering Code: 7285-0-3-611-XXHSE-1 E27 70W (6000 lm)

HIGH PRESSURE SODIUMOrdering Code: 7286-0-3-611-XXHSE-1 E27 2x70W (2x6000 lm)

HIGH PRESSURE SODIUMOrdering Code: 7287-0-3-611-XXHSE-1 E27 3x70W (3x6000 lm)

MERCURY VAPOUROrdering Code: 7285-0-3-511-XXHME E27 80W (4000 lm)

MERCURY VAPOUROrdering Code: 7286-0-3-511-XXHME E27 2x80W (2x4000 lm)

MERCURY VAPOUROrdering Code: 7287-0-3-511-XXHME E27 3x80W (3x4000 lm)

COMPACT FLUORESCENTOrdering code: 7285-0-3-436-XXTC-TEL Gx24q-4 42W (3200 lm)

COMPACT FLUORESCENTOrdering code: 7286-0-3-436-XXTC-TEL Gx24q-4 2x42W (2x3200 lm)

COMPACT FLUORESCENTOrdering code: 7287-0-3-436-XXTC-TEL Gx24q-4 3x42W (3x3200 lm)

SPECIFICATION CONSTRUCTION: Fixture is manufactured in compliance with IEC 60598-1 Electrical protection class 1. IP55 BODY: Head components in corrosion resistant high-pressure die- cast aluminium ADC12 alloy. This luminaire is to be used with extruded aluminium pole 105mm. Pole and ground installation unit are available seperately - please see detail on page 394,398,399. Special pole-entry on the luminaire for other pole size can be made upon request. OPTIC COVER: Self-extinguishing high impact resistant opal polycarbonate diffuser with UV stabilized additive from Elkamet - Germany. PROTECTION: Weather proof and durable silicone gasket. Service temperature -40 to +200 C. FASTENING: All external screw is in 316 stainless steel with silicone grease dipping. CABLE ENTRY: Prepare for H07RN-F cable 3G x1.0 with pull relife device. LAMP HOLDER: E27 ceramic nickle-coated contact from Vossloh Schwabe - Germany / ENEC approved. For discharge/tungsten halogen lamp. T270 rating 4/250/5kV. Gx24q-4 holder in PBT phosphor bronze contact from AAG Stucchi - Italy / ENEC approved. For compact fluorescent lamp. T140 rating 2A-250V.CONTROL GEAR: Magnetic ballast from Vossloh Schwabe - Germany / ENEC approved. 230V 50Hz tw130. For discharge lamp. High frequency electronic ballast from Vossloh Schwabe - Germany / ENEC approved. 220-240V 0-50-60Hz tc70 A2 EEI class. For 4 pins compact fluorescent lamp. Electronic superimposed ignitor with automatic switch-off feature from Vossloh Schwabe - Germany / ENEC approved. Ignition voltage 4-5kV 220-240V 50-60Hz. For ceramic/quartz discharge lamp. Power factor correction for discharge lamp from Vossloh Schwabe - Germany or from Electronicon - Germany. ENEC approved.WIRING: 1x0.75 tinned copper silicone rubber insulated cable from CET Eletric - Italy / IMQ approved. 2kV / -60 to +180 C service temperature. Double silicone insulation ignition wire. Tinned copper condutor. Impulsive voltage 5kV. Connector in PA6.6 nickle-plated brass insert. 600V/24A. - 40 to +130 C service temperature. Cross section 6mm. VDE approved. Wiring provided with earth connection.PAINTING: First Stage: Chromatization treatment, resistant to corrosive and extreme environment. Second Stage: Coated with UV stabilized polyester powder in automatic chamber. Third Stage: Baked in digital temperature control room at 200 C for 30 minutes.

AVAILABLE COLOR: Black - RAL9005 (replace last 2 digits on ordering code with 01) Graphite - RAL7016 (replace last 2 digits on ordering code with 02) Dark Grey - RAL7037 (replace last 2 digits on ordering code with 03) Aluminium Silver - RAL9006 (replace last 2 digits on ordering code with 04) White - RAL9010 (replace last 2 digits on ordering code with 06)

2

0

296

IP65 F

OD-7222 OD-7222

Indirect Symmertical Light Distribution Post-top Luminaire

NEW FOR 2006THIS IS PROVISION DATA ONLY.ACTUAL DIMENSION AND LOOK MAY DIFFER FROM THIS.

1000

756

800

140

105

297

NEW FOR 2006THIS IS PROVISION DATA ONLY.ACTUAL DIMENSION AND LOOK MAY DIFFER FROM THIS.

SPECIFICATION CONSTRUCTION: Fixture is manufactured in compliance with IEC 60598-1 Electrical protection class 1. IP65 BODY: Head components in corrosion resistant high-pressure die- cast aluminium ADC12 alloy. This luminaire is to be used with extruded aluminium pole 105mm. Pole and ground installation unit are available seperately - please see detail on page 394,398,399. Special pole-entry on the luminaire for other pole size can be made upon request. OPTIC COVER: Impact resistant transparent safety tempered glass. Able to stand sudden change in temperature of up to 250 C. REFLECTOR: Primary reflector in high purity anodized aluminium 99.90%. Secondary reflector in two layer thick spun aluminium. PROTECTION: Weather proof and durable silicone gasket. Service temperature -40 to +200 C. FASTENING: All external screw is in 316 stainless steel with silicone grease dipping.CABLE ENTRY: Prepare for H07RN-F cable 3G x1.0 with pull relife device. LAMP HOLDER: G12 holder in ceramic nickle-coated contact from Vossloh Schwabe - Germany / ENEC approved. For discharge lamp. T270 rating 4/250/5kV.CONTROL GEAR: Magnetic ballast from Vossloh Schwabe - Germany / ENEC approved. 230V 50Hz tw130. For discharge lamp. Electronic superimposed ignitor with automatic switch-off feature from Vossloh Schwabe - Germany / ENEC approved. Ignition voltage 4-5kV 220-240V 50-60Hz. For ceramic/quartz discharge lamp. Power factor correction for discharge lamp from Vossloh Schwabe - Germany or from Electronicon - Germany. ENEC approved.WIRING: 1x0.75 silicone rubber insulated cable with fiberglass braid from CET Eletric - Italy / IMQ approved. 2kV / -60 to +180 C service temperature. Double silicone insulation ignition wire. Tinned copper condutor. Impulsive voltage 5kV. Connector in PA6.6 nickle-plated brass insert. 600V/24A. - 40 to +130 C service temperature. Cross section 6mm. VDE approved. Wiring provided with earth connection.PAINTING: First Stage: Chromatization treatment, resistant to corrosive and extreme environment. Second Stage: Coated with UV stabilized polyester powder in automatic chamber. Third Stage: Baked in digital temperature control room at 200 C for 30 minutes.

AVAILABLE COLOR: Black - RAL9005 (replace last 2 digits on ordering code with 01) Graphite - RAL7016 (replace last 2 digits on ordering code with 02) Dark Grey - RAL7037 (replace last 2 digits on ordering code with 03) Aluminium Silver - RAL9006 (replace last 2 digits on ordering code with 04) White - RAL9010 (replace last 2 digits on ordering code with 06)

2

0 METAL HALIDEOrdering Code: 7222-0-3-752-XXHIT-CE G1270W (6600 lm)

METAL HALIDEOrdering Code: 7222-0-3-753-XXHIT-CE G12 150W (14500 lm)