View
247
Download
1
Category
Preview:
Citation preview
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 1/156
WARNING - This is a new format for application options.
If you have been accustomed to printing the application option page by usingCTL - P, be aware that the use of that key combination will cause the entire bookto print.
To print a single page, choose the File menu item at the top left of this windowand then select the Print command on the drop down menu. Then a pop-upwindow will give you the opportunity to specify whether you want to print theentire book, a group of pages or a single page.
DATA INCLUDED IN THIS BOOK IS SUBJECT TO CHANGE WITHOUT NOTICE.
Option compatibilities, option drawings, and other data listed in this book aresubject to change. Consult the Cummins IMS database for the latest informationor contact your Cummins representative. The dimensions shown in this book areincluded for comparative purposes and should not be used for other purposes.
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 2/156
N14-G (GENERATOR) DRIVEENGINE
PRODUCT SUMMARY
May, 2000
Model Name Configuration
Number
Application
Max Gross BHP(SAE)
1800 rpm 1500 rpm
N14-G1 D093638GX03
Standby 465 430
Prime Power 420 380
Continuous 350 340
N14-G2 D093638GX03
Standby 535 N/A
Prime Power 480 N/A
Continuous 375 N/A
* For Explanation of Option by Configuration Section see below
* Note:• All components and accessories are mounted and plumbed or wired unless otherwise noted.• Graphics for standard configuration options may be seen on the installation diagrams.• N.A. denotes item not available.• [G] denotes “General Option Category”.• [M] denotes “Mandatory Option Category”.
Caution:Proving torsional compatibility of an engine-generator set is the responsibility of the generator-set assembler. Cummins will supply the appropriate engine mass elastic data necessary for thecalculations and is prepared to offer assistance with torsional questions concerning the engine.
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 3/156
AC-Keydata
Option # Model/Size Duty Rating Inlet/Outlet Size Mounted or Kitted
AC 1152 FVG16-0152 Heavy Duty 178 mm [7.0 in.] Supplied in kit
AC 1153 FVG16-0152 Heavy Duty 178 mm[7.0 in.] Mounted
AC 1154178 mm
[7.0 in.]
AC 1160 FA-632–CU Single Stage Normal178 mm
[7.0 in.]Mounted
AC-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AC/ac-Keydata.htm [3/15/2002 10:17:28 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 4/156
C 1152
C - Air Cleaner
vision Date: 03/00
ption # Model/Size Duty Rating Inlet/Outlet Size Mounted or Kitted
C 1152 FVG16-0152 Heavy Duty 178 mm [7.0 in.] Supplied in kit
Cleaner. Has in excess of 25 GMS/CFM capacity at 635 mm [25 in.] water maximum restriction at air flows up to 1070 CFM [505 L
meter: 406 mm [16.0 in.]
e Inlet and End Outlet: 178 mm [7.0 in.]
y Rating: Heavy Duty
nufacturer: Donaldson
del: FVG16–0152
vironment Capability: Outdoor
ludes Air Inlet Cap, two mounting straps, safety element and Vacuator Valve for horzontal mounting.
AC 1152
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AC/ac-1152.htm [3/15/2002 10:17:26 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 5/156
C 1153
C - Air Cleaner
vision Date: 03/00
ption # Model/Size Duty Rating Inlet/Outlet Size Mounted or Kitted
C 1153 FVG16-0152 Heavy Duty178 mm
[7.0 in.]
Mounted
unted Air Cleaner.
e Inlet and End Outlet dia.: 178 mm [17.0 in.]
y Rating: Heavy Duty
nufacturer: Donaldson
del: FVG16-0152
vironment Capability: Outdoor
ludes Air Inlet Cap and Dust Ejector Valve.
AC 1153
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AC/ac-1153.htm [3/15/2002 10:17:27 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 6/156
C 1154
C - Air Cleaner
vision Date: 03/00
ption # Model/Size Duty Rating Inlet/Outlet Size Mounted or Kitted
C 1154178 mm
[7.0 in.]
cleaner cap for 178 mm [7.0 in.] intake diameter.
AC 1154
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AC/ac-1154.htm [3/15/2002 10:17:27 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 7/156
AC 1160
C - Air Cleaner
evision Date: 03/00
Option # Model/Size Duty Rating Inlet/Outlet Size Mounted or Kitted
AC 1160 FA-632–CU Single Stage Normal178 mm
[7.0 in.]Mounted
ounted Air Cleaner.
uty Rating: Normalanufacturer: FRAM
odel: FA-632-CU Single Stagenvironment Capability: Indoor
AC 1160
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AC/ac-1160.htm [3/15/2002 10:17:28 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 8/156
AD-Keydata
Option # Groove Bolt Circle HP Notes
AD 1247 Four — —Three grooves179 mm [7.04 in.] dia. and one groove
192 mm [7.55 in.]dia. to drive accessories
AD 1248 No content option
AD 1270 Three — —Two grooves 179 mm [7.04 in.] dia. to drive fan and o
groove of 179 mm [7.04 in.] dia. to drive accessories.
AD 1272 ThreeTwo grooves 179 mm [7.04 in.] dia. to drive fan and o
groove of 192 mm [7.55 in.] dia. to drive accessories.
AD-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AD/ad-Keydata.htm [3/15/2002 10:17:31 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 9/156
D 1247
D - Accessory Drive Pulley
vision Date: 03/00
ption # Groove Bolt Circle HP Notes
D 1247 Four — —Three grooves179 mm [7.04 in.] dia. and one groove of 192 mm [7.55 in.] dia. to drive
accessories
ur groove pulley rotates clockwise at engine speed. Pulley has three 179 mm [7.04 in.] dia. V-belt grooves for 12.7 mm [0.50 in.] bel
192 mm [7.55 in.] dia. V-belt groove for a 12.7 mm [0.50 in.] belt to drive accessories. Pulley grooves are 13.09 mm [0.515 in.] V t
AD 1247
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AD/ad-1247.htm [3/15/2002 10:17:29 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 10/156
D 1248
D - Accessory Drive Pulley
vision Date: 05/00
ption # Groove Bolt Circle HP Notes
D 1248 No content option
content option.
use when there is no future requirements to drive a fan or other accessories from the accessory drive pulley.
ended drive: None
AD 1248
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AD/ad-1248.htm [3/15/2002 10:17:29 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 11/156
D 1270
D - Accessory Drive Pulley
vision Date: 04/01
ption # Groove Bolt Circle HP Notes
D 1270 Three — —Two grooves 179 mm [7.04 in.] dia. to drive fan and one groove of 179 mm [7.04 in.] dia. to
drive accessories.
and accessory drive pulley rotates at engine speed in same direction as crankshaft. Has two 179 mm [7.04 in.] dia. V-belt grooves f
m [0.875 in.] belts to drive fan and one 179 mm [7.04 in.] dia. V-belt groove for 22 mm [0.875 in.] belt to drive accessory. Fan and
essory grooves are 20.32 mm [0.800 in.] type.
AD 1270
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AD/ad-1270.htm [3/15/2002 10:17:30 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 12/156
D 1272
D - Accessory Drive Pulley
vision Date: 04/01
ption # Groove Bolt Circle HP Notes
D 1272 ThreeTwo grooves 179 mm [7.04 in.] dia. to drive fan and one groove of 192 mm [7.55 in.] dia. to
drive accessories.
and accessory drive pulley rotates at engine speed in same direction as crankshaft. Has two 179 mm [7.04 in.] dia. V-belt grooves f
m [0.875 in.] belts to drive fan and one 192 mm [7.55 in.] dia. V-belt groove for 12.7 mm [0.50 in.] belt to drive accessory. Fan groov
32 mm [0.800 in.] type, accessory groove is 13.08 [0.515 in.] type.
AD 1272
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AD/ad-1272.htm [3/15/2002 10:17:31 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 13/156
AG-Keydata
Option # Restriction Notes
AG 1008635 mm H2O
[25 in. H2O]
AG-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AG/ag-Keydata.htm [3/15/2002 10:17:33 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 14/156
G 1008
G - Air Restriction Indicator
vision Date: 05/00
ption # Restriction Notes
G 1008635 mm H2O
[25 in. H2O]
air cleaner restriction indicators are set at 635 mm H2O [25 in. H2O] of water.
gle air cleaner restriction service indicator.
unted at the factory to air cleaner or intake piping as appropriate.
e only with mounted air cleaner.
AG 1008
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AG/ag-1008.htm [3/15/2002 10:17:32 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 15/156
AP-Keydata
Option # Agency Tier Level Notes
AP 1001 Non Certified
AP 1019 Certified,US EPA/CARB
AP-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AP/ap-Keydata.htm [3/15/2002 10:17:35 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 16/156
P 1001
P - Agency Approval
vision Date: 03/00
ption # Agency Tier Level Notes
P 1001 Non Certified
PROVAL AGENCY: Non Certified
s option may only be used in applications that do not require certification. It may not be used in the U.S. for industrial non-road or
omotive applications without an exemption.
AP 1001
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AP/ap-1001.htm [3/15/2002 10:17:34 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 17/156
P 1019
P - Agency Approval
vision Date: 03/00
ption # Agency Tier Level Notes
P 1019 Certified,US EPA/CARB
s certification states that the engine complies with certain emissions requirements established by the US EPA/CARB, tested in accor
h ISO 8178 D2 and is in compliance with the 1996 Mobile Off-Highway standard. For emissions levels per the D2 cycle, please refe
Engine Data Sheet.
emissions levels per the D2 cycle, please refer to the Engine Data Sheet.
AP 1019
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/AP/ap-1019.htm [3/15/2002 10:17:35 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 18/156
BC-Keydata
Option # Base Engine Hardware Notes
BC 1002 Standard G-Drive application
BC-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/BC/bc-Keydata.htm [3/15/2002 10:17:35 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 19/156
C 1002
C - Base Components
vision Date: 03/00
ption # Base Engine Hardware Notes
C 1002 Standard G-Drive application
e Components
piration: Turbocharged/Jacket Water Aftercooled
e Engine Hardware: Standard
duct: 96N14-STC
plication: G-Drive
BC 1002
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/BC/bc-1002.htm [3/15/2002 10:17:35 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 20/156
BR-Keydata
Option # Mounting Location Notes
BR 1178 Located over #6 cylinder Tube clipped and terminated below top of block
BR 1185 Breather located over #6 cylinder Tube terminates below oil pan rail
BR 1224 Located over #6 cylinder Tube extends to rear corner of cylinder block
BR-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/BR/br-Keydata.htm [3/15/2002 10:17:38 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 21/156
R 1178
R - Crankcase Breather
vision Date: 05/00
ption # Mounting Location Notes
R 1178 Located over #6 cylinder Tube clipped and terminated below top of block
ather located over #6 cylinder. Vent tube extends from #6 cylinder toward rear corner of exhaust side of block. Tube clipped and
minated below top of block.
BR 1178
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/BR/br-1178.htm [3/15/2002 10:17:36 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 22/156
R 1185
R - Crankcase Breather
vision Date: 06/00
ption # Description Notes
R 1185 Breather located over #6 cylinder Tube terminates below oil pan rail
ather located over #6 cylinder. Vent tube extends from #6 cylinder toward rear corner of exhaust side of block. Tube terminates belo
rail.
BR 1185
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/BR/br-1185.htm [3/15/2002 10:17:37 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 23/156
R 1224
R - Crankcase Breather
vision Date: 06/00
ption # Mounting Location Notes
R 1224 Located over #6 cylinder Tube extends to rear corner of cylinder block
ather located over #6 cylinder. Vent tube, extends from #6 cylinder with hose, routed down fuel pump side to rear corner of cylinder
BR 1224
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/BR/br-1224.htm [3/15/2002 10:17:38 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 24/156
CH-Keydata
Option # Wattage/Volts Cord Length Location Notes
CH 1004 1500W/120V305 mm
[12.0 in.]Rear of water header plate
CH 1005 1500W/120V 3.05 M [10 ft.] Rear of water header plate
CH-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/CH/ch-Keydata.htm [3/15/2002 10:17:40 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 25/156
H 1004
H - Coolant Heater Starting Aid
vision Date: 06/00
ption # Wattage/Volts Cord Length Location Notes
H 1004 1500W/120V305 mm
[12.0 in.]Rear of water header plate
0W, 120V coolant heater with 305 mm [12.0 in.] cord mounted in rear of water header plate.
te: NOTE: Electrical cord contained in this option; coolant heater contained in dependent WA option.
CH 1004
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/CH/ch-1004.htm [3/15/2002 10:17:40 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 26/156
CH 1005
H - Coolant Heater Starting Aid
evision Date: 06/00
Option # Wattage/Volts Cord Length Location Notes
CH 1005 1500W/120V 3.05 M [10 ft.] Rear of water header plate
00W, 120V coolant heater with 3.05 M [10 ft.] cord mounted in rear of water header plate.
ote: Electrical cord contained in this option; coolant heater contained in dependent WA optio
CH 1005
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/CH/ch-1005.htm [3/15/2002 10:17:40 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 27/156
DA-Keydata
Option # Type/DiaAddt'l Drive
PulleysPTO Provision
Engine Rated
Speed
DA 1178Viscous damper/343 mm
[13.52 in.]
No No 2100 RPM
DA 1216 Poly V, 215.9 mm [8.5 in.] Yes No 2100 RPM
DA 1217 Poly-V, 185.1 mm [7.29 in.] Yes No 2100 RPM
DA-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/DA/da-Keydata.htm [3/15/2002 10:17:43 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 28/156
DA 1178
A - Vibration Damper
vision Date: 03/00
Option # Type/Dia Addt'l Drive Pulleys PTO Provision Engine Rated Speed
A 1178 Viscous damper/343 mm [13.52 in.] No No 2100 RPM
bration damper with alternator driving crank pulley having two 13 mm [0.5 in.] V-grooves. Includes mounting hardware to crankfront PTO provision.
te: Inertia Information: Ifw=1.98 lb.in.sec.sq.g=0.94 lb.in.sec.sq.
DA 1178
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/DA/da-1178.htm [3/15/2002 10:17:41 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 29/156
A 1216
A - Vibration Damper
vision Date: 03/00
ption # Type/Dia Addt'l Drive Pulleys PTO Provision Engine Rated Speed
A 1216 Poly V, 215.9 mm [8.5 in.] Yes No 2100 RPM
ration damper for crank driven fan drives with 1:1 fan ratios. Alternator drive pulley groove type, Poly V, 215.9 mm [8.5 in.], 5 rib,
-section
DA 1216
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/DA/da-1216.htm [3/15/2002 10:17:41 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 30/156
A 1217
A - Vibration Damper
vision Date: 04/00
ption # Type/Dia Addt'l Drive Pulleys PTO Provision Engine Rated Speed
A 1217 Poly-V, 185.1 mm [7.29 in.] Yes No 2100 RPM
cous vibration damper for fan drives with 0.86, 0.75, 0.65 and 0.55:1 fan ratios. Poly-V, 185.1 mm [7.29 in.] 5 rib, `K' section groov
rnator drive pulley.
DA 1217
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/DA/da-1217.htm [3/15/2002 10:17:42 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 31/156
DF-Keydata
Option # Descripton Shaft Max Torque Notes
DF 1009
DF-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/DF/df-Keydata.htm [3/15/2002 10:17:43 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 32/156
F 1009
F - Front Gear Train Accessory Drive
vision Date: 03/00
ption # Descripton Shaft Max Torque Notes
F 1009
E A Pump Mounting Flange
content option to indicate pump is blanked-off. Use when SAE A hydraulic pump drive is required for customer supplied hydraulic
hat no drive provision is required.
te: Hydraulic pump coupling driven from rear of engine gear housing. Pump rotates in same direction of engine with drive ratio of 1
DF 1009
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/DF/df-1009.htm [3/15/2002 10:17:43 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 33/156
DL-Keydata
Option # Plumbing for Attachment Location Attachment Size Not
DL 1037 Fuel drainMounted at rear corner of rear valve cover
3/4–16 UNF-2A
DL-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/DL/dl-Keydata.htm [3/15/2002 10:17:45 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 34/156
L 1037
L - Fuel Drain Location
vision Date: 03/00
ption # Plumbing for Attachment Location Attachment Size Notes
L 1037 Fuel drain Mounted at rear corner of rear valve cover 3/4–16 UNF-2A
ector drain on fuel pump side of engine for use with check valves mounted at rear corner of rear valve cover. See FT options for cont
DL 1037
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/DL/dl-1037.htm [3/15/2002 10:17:44 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 35/156
EE-Keydata
Option # Manuf/Model Voltage/Amps Notes
EE 1205 Butec A5524/16 28V 55A Built— in voltage regulator
EE 1211 Delco Remy/ 20 SI-300 24V/35A Length:160 mm [6.3 in.]
EE-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/EE/ee-Keydata.htm [3/15/2002 10:17:47 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 36/156
E 1205
E - Alternator
vision Date: 03/00
ption # Manuf/Model Voltage/Amps Notes
E 1205 Butec A5524/16 28V 55A Built— in voltage regulator
V 55A Butec A5524/16 alternator with built— in voltage regulator.
EE 1205
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/EE/ee-1205.htm [3/15/2002 10:17:46 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 37/156
E 1211
E - Alternator
vision Date: 05/00
ption #Manufacturer/
Model
Voltage/
AmpsNotes
E 1211Delco Remy/
20 SI-30024V/35A
Length:
160 mm [6.3 in.]
ounding method: Negative
ulation provisions: No
ling Provisions: Nolt-in voltage regulator: Yes
ound wire supplier: Customer
que characteristics: None
arging System: Standard
tery Terminal: 1/4 — 28
erminal: Pin
EE 1211
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/EE/ee-1211.htm [3/15/2002 10:17:46 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 38/156
EH-Keydata
Option # Use With Mount Type Drive Ratio Notes
EH 1037 Delco Remy and Leece-Neville
EH 1038 Delco Remy and Leece-Neville Used with fixed fandrive
EH-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/EH/eh-Keydata.htm [3/15/2002 10:17:50 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 39/156
H 1037
H - Alternator Mounting
vision Date: 03/00
ption # Use With Mount Type Drive Ratio Notes
H 1037 Delco Remy and Leece-Neville
ernator mounting for Delco Remy and Leece-Neville alternators.
EH 1037
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/EH/eh-1037.htm [3/15/2002 10:17:49 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 40/156
H 1038
H - Alternator Mounting
vision Date: 05/00
ption # Use With Mount Type Drive Ratio Notes
H 1038 Delco Remy and Leece-Neville Used with fixed fan drive
ernator mounting for Delco Remy and Leece-Neville alternators. Contains jackscrew tensioner adjusting link. Used with fixed fan dr
EH 1038
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/EH/eh-1038.htm [3/15/2002 10:17:50 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 41/156
EM-Keydata
Option # Type Attachment Hole Damper Notes
EM 1309 Pad Two hole Yes
EM-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/EM/em-Keydata.htm [3/15/2002 10:17:52 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 42/156
M 1309
M - Front Engine Support
vision Date: 03/00
ption # Type Attachment Hole Damper Notes
M 1309 Pad Two hole Yes
o hole wide span, pad type front engine support for 0 deg. engine tilt.
EM 1309
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/EM/em-1309.htm [3/15/2002 10:17:51 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 43/156
ES-Keydata
Option # Description Notes
ES 1022EFC governor actuator is installed in fuel
pump AFC cavity
Includes an engine mounted magnetic
pickup. For use with stationary applicatio
only
ES 1023EFC governor actuator is installed in fuel
pump AFC cavity
Use with customer supplied governor
control module and magnetic pick-up
ES 1025EFC governor actuator is installed in fuel
pump AFC cavity
Includes an engine mounted magnetic
pick-up.
ES 1026EFC governor actuator is installed in thefuel pump AFC cavity
Includes engine mounted magnetic pick-u
ES-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/ES/es-Keydata.htm [3/15/2002 10:17:53 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 44/156
S 1022
S - Electronic Governor
vision Date: 05/00
ption # Description Notes
S 1022 EFC governor actuator is installed in fuel pump AFC cavityIncludes an engine mounted magnetic pickup. For use with
stationary applications only
mmins digital EFC governor.
V DC normally closed system.
ludes control unit with speed and droop adjustments supplied in kit. Does not include load sensing module.
l pump governor: limiting speed.
C governor actuator is installed in fuel pump AFC cavity.ntrol unit requires a 24V DC negative ground power supply.
ludes an engine mounted magnetic pickup.
r use with stationary applications only.
ES 1022
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/ES/es-1022.htm [3/15/2002 10:17:52 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 45/156
S 1023
S - Electronic Governor
vision Date: 05/00
ption # Description Notes
S 1023 EFC governor actuator is installed in fuel pump AFC cavityUse with customer supplied governor control module and
magnetic pick-up
mmins EFC governor. Includes normally closed actuator mounted in fuel pump AFC cavity and AFC style PTG/AUTO fuel pump.
quires 24V, insulated or negative ground power supply.
r use with customer supplied governor control module and magnetic pick-up.
ES 1023
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/ES/es-1023.htm [3/15/2002 10:17:52 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 46/156
S 1025
S - Electronic Governor
vision Date: 05/00
ption # Description Notes
S 1025 EFC governor actuator is installed in fuel pump AFC cavity Includes an engine mounted magnetic pick-up.
mmins EFC governor.
V DC normally closed system.
ntrol unit requires a 24V DC negative ground power supply.
l pump governor: Limiting speed
C governor actuator is installed in fuel pump AFC cavity.
ludes control unit with speed and droop adjustments supplied in kit.es not include load sensing module.
ludes an engine mounted magnetic pick-up.
ES 1025
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/ES/es-1025.htm [3/15/2002 10:17:52 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 47/156
S 1026
S - Electronic Governor
vision Date: 05/00
ption # Description Notes
S 1026 EFC governor actuator is installed in the fuel pump AFC cavity Includes engine mounted magnetic pick-up.
mmins EFC governor.
V DC normally closed system.
l pump governor: limiting speed.
C governor actuator is installed in the fuel pump AFC cavity.
ludes a plug-in type control module installed in the engine instrument panel or generator control panel.
es not include load sensing module.ntrol module requires a 24V DC negative ground power supply.
ES 1026
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/ES/es-1026.htm [3/15/2002 10:17:53 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 48/156
FA-Keydata
Option # Bolt Circle mm Drive Ratio Fan Center mm Tensioner Type
FA 1331 88.9 mm [3.5 in.] 1:1 514.4 mm [20.25 in.] Manual
FA 1369
FA 1392 0.86:1 514.4 [20.25] Manual
FA 1396 1.21:1 375.92 mm [14.80 in.] Manual
FA 1398 139.7 mm [5.5 in.] 1:1 303.2 mm [13.00 in.] Automatic
FA 1400 139.7 mm [5.5 in.] 0.86:1 330 mm [13.0 in.] Automatic
FA 1402 139.7 mm [5.5 in.] 0.86:1 381 mm [15.0 in.] Automatic
FA 1422 139.7 mm [5.5 in.] 0.65:1 406.7 mm [16.01 in.] Automatic
A-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FA/fa-Keydata.htm [3/15/2002 10:18:00 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 49/156
FA 1331
A - Fan Drive
evision Date: 06/00
Option # Bolt Circle mm Drive Ratio Fan Center mm Tensioner Type
FA 1331 88.9 mm [3.5 in.] 1:1 514.4 mm [20.25 in.] Manual
elt Driven 1:1 Ratio - Continuous Drive Fan Hub, base support, bracket, two 22 mm [0.875 in.] bel
d fan hub adjusting screw.
an Center Style: Adjustable
an Hub Pilot Diameter: 65 mm [2.56 in.]
an Bracket Type: Vertical Adjusting
ulley Groove Type: Dual [0.8 in.] V
an Pulley Diameter: 179 mm [7.0 in.]
an Drive Groove Location: 129.8 mm [5.11 in.]
an Hub Adjusting Screw Supplier: Cummins
elt Tension Method: Manual
an Bracket Mounting Location: Block Mounted
an Mounting Surface Location: 201 mm [7.9 in.]
A 1331
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FA/fa-1331.htm [3/15/2002 10:17:53 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 50/156
A 1369
A - Fan Drive
vision Date: 05/00
ption # Bolt Circle mm Drive Ratio mm Fan Center mm Tensioner Type
A 1369
content option. When customer has no future requirements to drive fan from accessory drive pulley. Also may be used when the cus
plies own fan drive on a triangulated fan drive arrangement.
r use when the customer has no future requirements to drive a fan from the accessory drive pulley.
A 1369
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FA/fa-1369.htm [3/15/2002 10:17:54 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 51/156
A 1392
A - Fan Drive
vision Date: 04/00
ption # Bolt Circle mm Drive Ratio Fan Center mm Tensioner Type
A 1392 0.86:1 514.4 [20.25] Manual
mmins supplied fan drive.
Center Location: 514.35 mm [20.25 in.]
Drive Ratio: 0.86:1
Center Style: Adjustable
Hub Pilot Diameter: 81 mm [3.18 in.]
Bracket Type: Vertical Adjusting
ley Groove Type: Three 0.515 in. V
Pulley Diameter: 208 mm [8.2 in.]
Drive Groove Location: 130 mm [5.11 in.]
A 1392
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FA/fa-1392.htm (1 of 2) [3/15/2002 10:17:55 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 52/156
Hub Adjusting Screw Supplier: Cummins
t Tensioning Method: Manual
Bracket Mounting Location: Block Mounted
Mounting Surface Location: 236 mm [9.3 in.]
A 1392
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FA/fa-1392.htm (2 of 2) [3/15/2002 10:17:55 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 53/156
A 1396
A - Fan Drive
vision Date: 03/00
ption # Bolt Circle mm Drive Ratio Fan Center mm Tensioner Type
A 1396 1.21:1 375.92 mm [14.80 in.] Manual
mmins supplied fan drive.
Center Location: 375.92 mm [14.80 in.]
Drive Ratio: 1.21:1
Center Style: Adjustable
Hub Pilot Diameter: 65 mm [2.56 in.]
Bracket Type: Pivot
ley Groove Type: Dual 0.800 in. V
Pulley Diameter: 147.701 mm [5.815 in.]
Drive Groove Location: 130.9 mm [5.16 in.]
Hub Adjusting Screw Supplier: Cummins
t Tensioning Method: Manual
Bracket Mounting Location: Block Mounted
Mounting Surface Location: 200.66 mm [7.9 in.]
A 1396
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FA/fa-1396.htm [3/15/2002 10:17:56 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 54/156
A 1398
A - Fan Drive
vision Date: 05/00
ption # Bolt Circle mm Drive Ratio mm Fan Center mm Tensioner Type
A 1398 139.7 mm [5.5 in.] 1:1 303.2 mm [13.00 in.] Automatic
mmins supplied fan drive.
Center Location: 330.2 mm [13 in.]
Drive Ratio: 1.00:1
Center Style: Fixed
Hub Pilot Diameter: 76.2 mm [3.0 in.]
ley Groove Type: Poly V 12 Rib `K'
Pulley Diameter: 215.9 mm [8.500 in.]
Drive Groove Location: 158.09 mm [6.224 in.]
t Tensioning Method: Automatic
Bracket Mounting Location: Front of water pump
A 1398
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FA/fa-1398.htm (1 of 2) [3/15/2002 10:17:57 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 55/156
Mounting Surface Location: 245.364 mm [9.66 in.]
ximum Torque Capability: 203.7 N·m [150.0 lb.ft.]
ximum Fan Inertia: 1.32 N·m —sec sq [10 in.lb-sec sq]
ximum Bending Moment: 62.242 N·m [550 in.lb]
ximum Fan Weight: 49.9 kg [110 lb.]
ximum Fan Spacer Thickness: 127 mm [5.0 in.]
A 1398
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FA/fa-1398.htm (2 of 2) [3/15/2002 10:17:57 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 56/156
A 1400
A - Fan Drive
vision Date: 05/00
ption # Bolt Circle mm Drive Ratio mm Fan Center mm Tensioner Type
A 1400 139.7 mm [5.5 in.] 0.86:1 330 mm [13.0 in.] Automatic
mmins supplied fan drive.
Center Location: 330.2 mm [13.00 in.]
Drive Ratio: 0.86:1
Center Style: Fixed
Hub Pilot Diameter: 76.2 mm [3.0 in.]
ley Groove Type: Poly V 12 Rib `K'
Pulley Diameter: 215.9 mm [8.500 in.]
Drive Groove Location: 158.09 mm [6.224 in.]
t Tension Method: Automatic
Bracket Mounting Location: Front of Water Pump
A 1400
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FA/fa-1400.htm (1 of 2) [3/15/2002 10:17:58 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 57/156
Mounting Surface Location: 245.364 mm [9.66 in.]
ximum Torque Capability: 237.65 N·m [175.0 lb.ft.]
ximum Fan Inertia: 1.697 N·m —sec sq [550 in.lb]
ximum Fan Weight: 49.9 kg [110 lb.]
ximum Fan Spacer Thickness: 127 mm [5.0 in.]
A 1400
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FA/fa-1400.htm (2 of 2) [3/15/2002 10:17:58 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 58/156
A 1402
A - Fan Drive
vision Date: 05/00
ption # Bolt Circle mm Drive Ratio mm Fan Center mm Tensioner Type
A 1402 139.7 mm [5.5 in.] 0.86:1 381 mm [15.0 in.] Automatic
mmins supplied fan drive.
Center Location: 381 mm [15.00 in.]
Drive Ratio: 0.86:1
Center Style: Fixed
Hub Pilot Diameter: 76.2 mm [3.0 in.]
ley Groove Type: Poly V 12 Rib `K'
Pulley Diameter: 215.9 mm [8.500 in.]
Drive Groove Location: 158.09 mm [6.224 in.]
t Tension Method: Automatic
A 1402
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FA/fa-1402.htm (1 of 2) [3/15/2002 10:17:59 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 59/156
Bracket Mounting Location: Front of Water Pump
Mounting Surface Location: 245.364 mm [9.66 in.]
ximum Torque Capability: 237.65 N·m [175.0 lb.ft.]
ximum Fan Inertia: 1.697 N·m —sec sq [15 in.lb-sec sq]
ximum Bending Moment: 62.242 N·m [550 in.lb]
ximum Fan Weight: 49.9 kg [110 lb.]
ximum Fan Spacer Thickness: 127 mm [5.0 in.]
A 1402
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FA/fa-1402.htm (2 of 2) [3/15/2002 10:17:59 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 60/156
A 1422
A - Fan Drive
vision Date: 05/00
ption # Bolt Circle mm Drive Ratio mm Fan Center mm Tensioner Type
A 1422 139.7 mm [5.5 in.] 0.65:1 406.7 mm [16.01 in.] Automatic
mmins supplied fan drive.
Center Location: 406.4 mm [16.00 in.]
Drive Ratio: 0.65:1
Center Style: Fixed
Hub Pilot Diameter: 76.2 mm [3.0 in.]
ley Groove Type: Poly V 12 Rib `K'
Pulley Diameter: 286.512 mm [11.280 in.]
Drive Groove Location: 158.09 mm [6.224 in.]
t Tension Method: Automatic
Bracket Mounting Location: Front of Water Pump
Mounting Surface Location: 245.364 mm [9.66 in.]
A 1422
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FA/fa-1422.htm (1 of 2) [3/15/2002 10:18:00 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 61/156
ximum Torque Capability: 312.34 N·m [230.0 lb.ft.]
ximum Fan Inertia: 2.829 N·m —sec sq [25 in.lb-sec sq]
ximum Bending Moment: 62.242 N·m [550 in.lb]
ximum Fan Weight: 49.9 kg [110 lb.]
ximum Fan Spacer Thickness: 127 mm [5.0 in.]
A 1422
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FA/fa-1422.htm (2 of 2) [3/15/2002 10:18:00 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 62/156
FF-Keydata
Option # Element FiltrationWater Separator/WIF
SensorLocation/Notes
FF 1230 Single spin-on10 micron fuel
filter
Mounted on rear of fuel
pump
Straight inlet fittin
FF 1233 Dual spin-on10 micron fuel
filter
FF 1240 Single spin-on10 micron fuel
filter
Mounted on rear of fuel
pumpStraight inlet fittin
FF 1246 Dual spin-on10 micron fuelfilter
Mounted above pan rail atcenter of the fuel pump
F-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FF/ff-Keydata.htm [3/15/2002 10:18:02 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 63/156
FF 1230
F - Fuel Filter
evision Date: 03/00
Option # Element FiltrationWater Separator/WIF
SensorLocation/Note
FF 1230 Single spin-on10 micron fuel
filterMounted on rear of fuel pump Straight inlet fitt
ngle spin-on fuel/water separator mounted on rear of fuel pump. Provides straight inlet fitting. Con0 micron fuel filter. Can be used with all fuel pump types, but must be used on CENTRY or EFC
tuated fuel pump applications.
F 1230
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FF/ff-1230.htm [3/15/2002 10:18:01 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 64/156
FF 1233
F - Fuel Filter
evision Date: 03/00
Option # Element Filtration Water Separator/WIF Sensor Location/Notes
FF 1233 Dual spin-on 10 micron fuel filter
ual spin-on fuel filters mounting above pan rail at the center of the fuel pump side of engine. Has 9
gree fuel inlet fitting. To be used with straight fuel pump inlet fitting. Contains 10 micron fuel filte
an be used with all fuel pump types, but must be used on CENTRY or AFC actuated fuel pumpplications.
F 1233
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FF/ff-1233.htm [3/15/2002 10:18:01 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 65/156
FF 1240
F - Fuel Filter
evision Date: 03/00
Option # Element FiltrationWater Separator/WIF
SensorLocation/Note
FF 1240 Single spin-on10 micron fuel
filterMounted on rear of fuel pump Straight inlet fitt
ngle spin-on fuel/water separator mounted on rear of fuel pump.ovides straight inlet fitting.
ontains 10 micron fuel filter.an be used with all fuel pump types, but must be used on CENTRY or EFC actuated fuel pump
plications.
ontains smaller element (FS 1001) to overcome foul condition with hydraulic pump when filter is
ounted direct to the fuel (REF FF 1230).
rst released for Case Quad tractors.
F 1240
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FF/ff-1240.htm [3/15/2002 10:18:01 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 66/156
FF 1246
F - Fuel Filter
evision Date: 03/00
Option # Element Filtration Water Separator/WIF Sensor Location/No
FF 1246 Dual spin-on 10 micron fuel filterMounted above pan rail at center
of the fuel pump
ual spin-on fuel/water separator mounted above pan rail at center of the fuel pump side of engine. H
0 degree fuel inlet fitting. To be used with straight fuel pump inlet fitting.ontains 10-micron fuel filters.
F 1246
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FF/ff-1246.htm [3/15/2002 10:18:01 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 67/156
FH-Keydata
Option # SAE/Wet or Dry Application Housing Material Starter Quadrant
FH 1504Hardware for customer
supplied flywheel
housing
FH 11057 SAE #1/DryHigh and low vertical
padsCast iron #2
FH 11071 SAE#0/Dry Vertical pads AluminumQuadrant #2 and
#3
H-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FH/fh-Keydata.htm [3/15/2002 10:18:04 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 68/156
H 11057
H - Flywheel Housing
vision Date: 07/01
Option # SAE/Wet or Dry Application Housing Material Starter Quadrant
H 11057 SAE #1/Dry High and low vertical pads Cast iron #2
E #1 dry type closed cast iron flywheel housing with both high and low mounting pads machined. Starter bore machined on exhaust
y, No. 2 quadrant. Has provision for magnetic pick-up.
H 11057
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FH/fh-11057.htm [3/15/2002 10:18:03 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 69/156
H 11071
H - Flywheel Housing
vision Date: 05/00
Option # SAE/Wet or Dry Application Housing Material Starter Quadrant
H 11071 SAE#0/Dry Vertical pads Aluminum Quadrant #2 and #3
dry applications. Aluminum flywheel housing with starter locations in quadrant #2 and #3. Housing machined for 5/8-18 threaded
gnetic pickup.
H 11071
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FH/fh-11071.htm [3/15/2002 10:18:04 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 70/156
H 1504
H - Flywheel Housing
vision Date: 05/00
ption # SAE/Wet or Dry Application Housing Material Starter Quadrant
H 1504 Hardware for customer supplied flywheel housing
dware for customer supplied flywheel housing. Includes rear crankshaft oil seal, mounting hardware, and 13 mm [0.500 in.] dowel p
es not include dust cover.
H 1504
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FH/fh-1504.htm [3/15/2002 10:18:04 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 71/156
FN-Keydata
Option # Type Diameter Max Speed Material
FN 1008 Right hand blower / Left hand sucker812.8 mm
[32 in.]
FN 3608 Blower914 mm
[36 in.]1950 RPM Aluminum
FN 3610 Sucker914.4 mm
[36 in.]1950 RPM Aluminum
N-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FN/fn-Keydata.htm [3/15/2002 10:18:07 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 72/156
N 1008
N - Fan
vision Date: 03/00
ption # Type Diameter Max Speed Material
N 1008 Right hand blower / Left hand sucker 812.8 mm[32 in.]
gine fan.
meter: 812.8 mm [32 in.]
mber of Blades: 6
pe of Fan: Right hand blower / Left hand sucker
ximum Speed Limitation: TBD
unting Bolt Circle Diameter: 89 mm [3.5 in.]
unting Flange Thickness: TBD
terial: TBD
ot Diameter: 51 mm [2.0 in.]
N 1008
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FN/fn-1008.htm [3/15/2002 10:18:05 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 73/156
N 3608
N - Engine Fan
vision Date: 08/00
ption # Type Diameter Max Speed Material
N 3608 Blower914 mm
[36 in.]1950 RPM Aluminum
mm [36 in.] dia. aluminum blower type 8-blade fan. 140 mm
5 in.] B.C. and 76 mm [3 in.] dia. pilot. Mounting flange thickness is 25.6 mm [1.01 in.]. Kitted.
ximum Fan Speed = 1950 RPM.
N 3608
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FN/fn-3608.htm [3/15/2002 10:18:06 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 74/156
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 75/156
FR-Keydata
Option # Horsepower/Kilowatts Speed CPL Certified
FR 10020535 BHP
399 kWm1800 rpm CPL 2287 EPA, CARB
FR 10027347 kWm [465 BHP]
320 kWm [430 BHP]
1800 rpm
1500 rpm
CPL 2287
CPL 2287
EPA, CARB
EPA, CARB
R-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FR/fr-Keydata.htm [3/15/2002 10:18:08 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 76/156
R 10020
R - Power Rating
vision Date: 05/00
Option # Horsepower/Kilowatts Speed CPL Certified
R 10020535 BHP
399 kWm1800 rpm CPL 2287 EPA, CARB
gine performance capability in accordance with ISO-3046 conditions of:
00 kPa [29.53 in. Hg] barometric pressure
0 m [361 ft.] altitude
°C [77 °F] air inlet temperature0% relative humidity
ng No. 2 diesel fuel per ASTM D-975.
r use with N14–G2 only.
ndby Power Application Only.
R 10020
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FR/fr-10020.htm [3/15/2002 10:18:07 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 77/156
R 10027
R - Power Rating
vision Date: 05/00
Option # Horsepower/Kilowatts Speed CPL Certified
R 10027347 kWm [465 BHP]
320 kWm [430 BHP]
1800 rpm
1500 rpm
CPL 2287
CPL 2287
EPA, CARB
EPA, CARB
gine performance capability in accordance with ISO-3046 conditions of:
00 kPa [29.53 in. Hg] barometric pressure
0 m [361 ft.] altitude 25 °C [77 °F] air inlet temperature
0% relative humidity
ng No. 2 diesel fuel per ASTM D-975.
r use with N14–G1 only.
ndby Power Application Only.
R 10027
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FR/fr-10027.htm [3/15/2002 10:18:08 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 78/156
FV-Keydata
Option # Volts/Description Location Notes
FV 1024 24V DC rapid restart Fuel pump mounted
V-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FV/fv-Keydata.htm [3/15/2002 10:18:09 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 79/156
V 1024
V - Fuel Shutoff Valve
vision Date: 05/00
ption # Volts/Description Location Notes
V 1024 24V DC rapid restart Fuel pump mounted
V DC solenoid operated rapid restart fuel shut-off valve.
gle/Internal ground.
V 1024
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FV/fv-1024.htm [3/15/2002 10:18:09 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 80/156
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 81/156
W 1010
W - Flywheel
vision Date: 05/00
ption # SAE Pilot Bearing Bore Dia. Ring Gear Pitch/Tooth Indicated Drive
W 1010 SAE #1 80 mm [3.15 in.] 6/8–118 SAE 14 OCC
ets SAE J162 for No. 514 Generator Flex Disc. Also meets SAE J620C for SAE 14 Overcenter Clutch.
visions for 356 mm [14. in.] overcenter clutch adaptation. Includes 118 tooth, 6/8 pitch ring gear for 276 mm [10.85 in.] starter cent
ance.
W 1010
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FW/fw-1010.htm [3/15/2002 10:18:10 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 82/156
W 1502
W - Flywheel
vision Date: 03/00
ption # SAE Pilot Bearing Bore Dia. Ring Gear Pitch/Tooth Indicated Drive
W 1502
content option.
ed when flywheel is omitted.
W 1502
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/FW/fw-1502.htm [3/15/2002 10:18:10 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 83/156
LA-Keydata
Option Bracket Bracket Provided Max. Lifting Load Notes
LA 1061 Two Yes-two —Studded capscrew for mounting
tube clips
A-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/LA/la-Keydata.htm [3/15/2002 10:18:12 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 84/156
A 1061
A - Lifting Arrangement
vision Date: 06/00
Option Bracket Bracket Provided Max. Lifting Load Notes
LA 1061 Two Yes-two — Studded capscrew for mounting tube clips
ackets located at front and rear of engine, mounted on cylinder heads.
A 1061
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/LA/la-1061.htm [3/15/2002 10:18:11 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 85/156
LE-Keydata
Option # Description
LE 1002
E-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/LE/le-Keydata.htm [3/15/2002 10:18:12 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 86/156
E 1002
E - Engine Performance Test
vision Date: 03/00
ption # Description
E 1002
gine Test performance. Ship copy of Engine Test Log with engine.
E 1002
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/LE/le-1002.htm [3/15/2002 10:18:12 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 87/156
LF-Keydata
Option # Type Hose Length Location Notes
LF 1173 Combination, full flow/bypass N/A Direct to filter head Direct
LF 1213 Combo
F-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/LF/lf-Keydata.htm [3/15/2002 10:18:14 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 88/156
F 1173
F - Lube Oil Filter
vision Date: 06/00
ption # Type Hose Length Location Notes
F 1173 Combination, full flow/bypass N/A Direct to filter head Direct
gine mounted, spin-on, combination, full flow/bypass lube oil filter.
pass oil filter hose fittings in cooler and block are orientated upward at approx 12:00 positions to give the hose an upward loop.
s is the standard bypass hose position.
F 1173
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/LF/lf-1173.htm [3/15/2002 10:18:14 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 89/156
F 1213
F - Oil Filter
vision Date: 05/00
ption # Type Hose Length Location Notes
F 1213 Combo
gine mounted, spin-on, combination, full flow/bypass lube oil filter.
pass oil filter hose fittings in cooler and block are orientated upward at approx 12:00 positions to give the hose an upward loop.
s is the standard bypass hose position.
F 1213
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/LF/lf-1213.htm [3/15/2002 10:18:14 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 90/156
LG-Keydata
Option # Handle Orientation Location of Entry Into Oil Pan Use With Power Angle
LG 1018 Right HHC 0 deg
G-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/LG/lg-Keydata.htm [3/15/2002 10:18:15 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 91/156
G 1018
G - Oil Level Gauge
vision Date: 06/00
ption # Handle Orientation Location of Entry Into Oil Pan Use With Power Angle
G 1018 Right HHC 0 deg
level dipstick and tube for rear sump oil pan. Calibrated for 0 deg. power angle and 0 deg. tilt. Tube is 114 mm [4.5 in.] long, and pr
e.
te: Calibrated for 36 L [9.5 U.S. gal.] high and 28.4 L [7.5 U.S. gal.] low.
G 1018
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/LG/lg-1018.htm [3/15/2002 10:18:15 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 92/156
LO-Keydata
Option # Notes
LO 1002 Includes tag stating that engine is filled with lubricating oil
O-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/LO/lo-Keydata.htm [3/15/2002 10:18:16 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 93/156
O 1002
O - Lubricating Oil
vision Date: 06/00
ption # Notes
O 1002 Includes tag stating that engine is filled with lubricating oil
e 15W40 lubricating oil for filling engine prior to shipment. Includes tag stating that engine is filled with lubricating oil.
O 1002
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/LO/lo-1002.htm [3/15/2002 10:18:16 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 94/156
LT-Keydata
Option # Description
LT 1054 N14-G G-Drive engine
LT 1060 Literature
T-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/LT/lt-Keydata.htm [3/15/2002 10:18:17 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 95/156
T 1054
T - Literature
vision Date: 03/00
ption # Description
T 1054 N14-G G-Drive engine
erature for N14-G G-Drive engine.
ludes:
ngine Parts Catalog
peration and Maintenance manual
pplied in kit.
T 1054
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/LT/lt-1054.htm [3/15/2002 10:18:16 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 96/156
T 1060
T - Literature
vision Date: 05/00
ption # Description
T 1060 Literature
erature for G-Drive engines. This option specifies declaration of incorporation in accordance with E.C. machinery directive 89/392/E
ended by E.C. directive 91/368/EEC.
T 1060
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/LT/lt-1060.htm [3/15/2002 10:18:17 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 97/156
OB-Keydata
Option # Location Fill Type With Dipstick Notes
OB 1342 Exhaust side of engine N/A YesHas provision for press-fit typ
oil gauge tube
OB 1347 Exhaust side of engine T-handle YesHas provision for press-fit typ
oil gauge tube
OB-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/OB/ob-Keydata.htm [3/15/2002 10:18:19 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 98/156
OB 1342
B - Oil Fill Arrangement
vision Date: 05/00
ption # Location Fill Type With Dipstick Notes
B 1342 Exhaust side of engine N/A Yes Has provision for press-fit type oil gauge tube
nd hole cover located on exhaust side of engine.
provision for press-fit type oil gauge tube.
provision for oil fill.
OB 1342
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/OB/ob-1342.htm [3/15/2002 10:18:18 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 99/156
OB 1347
B - Oil Fill Arrangement
vision Date: 05/00
ption # Location Fill Type With Dipstick Notes
B 1347 Exhaust side of engine T-handle Yes Has provision for press-fit type oil gauge tube
nd hole cover located on exhaust side of engine with 25 mm [1.0 in.] oil filler tube. Has provision for press-fit type oil gauge tube.
OB 1347
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/OB/ob-1347.htm [3/15/2002 10:18:19 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 100/156
OH-Keydata
Option # Description Voltage/Watts Cord Length
OH 1003 Factory installed 240V AC, 300W
OH-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/OH/oh-Keydata.htm [3/15/2002 10:18:21 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 101/156
OH 1003
H - Oil Heater Starting Aid
vision Date: 05/00
ption # Description Voltage/Watts Cord Length
H 1003 Factory installed 240V AC, 300W
unted 240V AC, 300W oil heater starting aid with provision for cord.
OH 1003
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/OH/oh-1003.htm [3/15/2002 10:18:20 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 102/156
OP-Keydata
Option # Type/Material Sump Location Angularity Capacity
OP 1449 Stamped steel Rear
Front down: 45 deg.
Front up:
45 deg.Side to side: 45 deg.
36 L
[9.5 U.S. gal]
OP-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/OP/op-Keydata.htm [3/15/2002 10:18:22 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 103/156
OP 1449
P - Oil Pan
vision Date: 04/00
ption # Type/Material Sump Location Angularity Capacity
P 1449 Stamped steel Rear
Front down: 45 deg.
Front up:
45 deg.
Side to side: 45 deg.
36 L
[9.5 U.S. gal]
ar sump, stamped steel oil pan.
gularity
ont down: 45 deg.
ont up: 45 deg.
de to side: 45 deg.
pan capacity: 36 litres [9.5 U.S. gal.]
OP 1449
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/OP/op-1449.htm [3/15/2002 10:18:22 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 104/156
PR-Keydata
Option # Description
PR 1002 Light
PR 1003 Heavy Tarp–B on FW/FA
PR 1007 Light Ferrocote on FW
PR 1010 Light Ferrocote and cheese cloth on FW/FA
PR-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/PR/pr-Keydata.htm [3/15/2002 10:18:23 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 105/156
R 1002
R - Corrosion Preventive
vision Date: 06/00
ption # Description
R 1002 Light
ght” rustproofing on flywheel and fan bracket mounting areas. Use on engines having normal exposure to the environment during sh
storage.
PR 1002
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/PR/pr-1002.htm [3/15/2002 10:18:22 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 106/156
R 1003
R - Corrosion Preventative
vision Date: 06/00
ption # Description
R 1003 Heavy Tarp–B on FW/FA
eavy” rustproofing using Tarp—B on flywheels and fan bracket mounting areas of engines having severe exposure to the environme
ing shipping and storage (i.e. engines shipped on open trailers, stored in uncontrolled environment storage areas, and/or subjected to
.
PR 1003
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/PR/pr-1003.htm [3/15/2002 10:18:23 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 107/156
R 1007
R - Corrosion Preventative
vision Date: 06/00
ption # Description
R 1007 Light Ferrocote on FW
ght” rustproofing with Ferrocote (5856HF-3) on “flywheels only” of engines having normal exposure to the environment during ship
storage (i.e. engines shipped on closed trailers and/or stored in controlled environment storage areas).
PR 1007
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/PR/pr-1007.htm [3/15/2002 10:18:23 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 108/156
R 1010
R — Corrosion Preventative
vision Date: 05/00
ption # Description
R 1010 Light Ferrocote and cheese cloth on FW/FA
ght” rustproofing using Ferrocote (5856HF-3) and cheese cloth on flywheel and fan brackets mounting areas of engines having norm
osure to the environment during shipping and storage. (i.e. engines shipped on closed trailers and/or stored in a controlled environm
age areas).
PR 1010
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/PR/pr-1010.htm [3/15/2002 10:18:23 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 109/156
RD-Keydata
Option # Supply Method Connection Type Components Supplied Notes
RD 1004 Supplied in kit Threaded female Item far left in graphic only —
RD 1013 Mounted in oil pan Aluminum or steel stamped
RD-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/RD/rd-Keydata.htm [3/15/2002 10:18:25 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 110/156
D 1004
D - Remote Oil Drain
vision Date: 05/00
ption # Supply Method Connection Type Components Supplied Notes
D 1004 Supplied in kit Threaded female Item far left in graphic only —
pan drain adapter with 3/4 in. NPTF for remote drain.
pplied in kit.
RD 1004
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/RD/rd-1004.htm [3/15/2002 10:18:24 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 111/156
RD 1013
D - Remote Oil Drain
evision Date: 03/00
Option # Supply Method Connection Type Oil Pan Material
RD 1013 Mounted in oil pan Aluminum or steel stamped
emote oil drain.
upply Method: Mounted in oil pan
ems included: 1-18 UNS-2A threaded shutoff valveil Pan Material: Aluminum or steel stamped
his is an oil drain that uses a locking draincock in place of the standard drain plug for quick
rainage.
RD 1013
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/RD/rd-1013.htm [3/15/2002 10:18:24 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 112/156
SD-Keydata
Option # Type Description
SD 1030
SD 1031
SD 1032
SD 1037
SD 1038
SD-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SD/sd-Keydata.htm [3/15/2002 10:18:26 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 113/156
D 1030
D - Monitoring Switches
vision Date: 03/00
ption # Type Description
D 1030
Pressure switch
unting: 1/8 NPT
ivates: 35 +/- 3 PSI [71.3 +/- 6.1 in. Hg]
activates: 25 +/- 3 PSI [50.9 +/- 6.1 Hg]
ludes adaptive harness (Packard Part No. 12047911).
SD 1030
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SD/sd-1030.htm [3/15/2002 10:18:25 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 114/156
D 1031
D - Monitoring Switches
vision Date: 03/00
ption # Type Description
D 1031
olant temperature switch
unting: 1/2 NPT
ivates: 106 +/- 1.7 °C [223 +/- 3 °F]
activates: 103 +/- 1.7 °C [218 +/- 3 °F]
ludes adaptive harness (Packard Part No. 12047911).
SD 1031
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SD/sd-1031.htm [3/15/2002 10:18:25 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 115/156
D 1032
D - Monitoring Switches
vision Date: 03/00
ption # Type Description
D 1032
olant pressure switch
unting: 1/2 NPT
ivates: 14 PSI [28.5 in. Hg] Max.
activates: 6 +/- 2 PSI [12 +/- 4 in. Hg]
ludes adaptive harness (Packard Part No. 12047911).
SD 1032
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SD/sd-1032.htm [3/15/2002 10:18:25 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 116/156
D 1037
D - Monitoring Switches
vision Date: 03/00
ption # Type Description
D 1037
erspeed switch.
ber-Colman Dynalco 24V solid state triple element speed switch with manual reset for crank cut-out, paralleling and overspeed shut
use with semi-automatic or automatic paralleling.
ustment range of N.O. crank cut-out contact 300-700 RPM; set to trip at 325 RPM.
ustment range of N.O. paralleling contact 600-2100 RPM; set to trip at 800 RPM.
ustment range of N.O. and N.C. overspeed shutdown contacts 1500-4000 RPM; set to trip at 2070 RPM.pplied in kit.
te: NOTE: The above settings are for SAE #0 flywheels with 142 teeth in the ring gear. When used with SAE #1 flywheel with
th or SAE #00 flywheel with 168 teeth, switch must be re-adjusted to correct speed. Requires magnetic pick-up, contained in
endent option EO 1701 for operation.
SD 1037
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SD/sd-1037.htm [3/15/2002 10:18:26 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 117/156
D 1038
D - Monitoring Switches
vision Date: 03/00
ption # Type Description
D 1038
gine monitoring system.
o low lube oil pressure switches. One switch provides an alarm on decreasing pressure at 124 +/- 14 kPa [18 +/- 2 PSI].
econd switch shuts the engine down on deceasing pressure at 83 +/- 14 kPa [12 +/- 2 PSI].
o high coolant temperature switches. One switch provides an alarm on increasing temperature at 102 +/- 1.7 °C [215 +/- 3 °F].
econd switch shuts the engine down on increasing temperature at 106 +/- 1.7 °C [223 +/- 3 °F]
eparate low coolant temperature switch provides an alarm on decreasing temperature at 32 +/- 1°C [90 +/- 2 °F].nnot be used with Cummins supplied engine wiring harness.
SD 1038
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SD/sd-1038.htm [3/15/2002 10:18:26 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 118/156
SK-Keydata
Option # Description Disposition Material Notes
SK 1005Skid used with fan to
flywheel engine.Wooden box No content option
SK 1006
Front shipping bracket
and mounting screws for
fan to flywheel bare
engine
Wooden skid Domestic use only
SK 1007Skid for fan to flywheel
engineWooden Domestic use only
SK 1008
Front shipping bracket for
fan to flywheel bareengine Wooden skid For international use only
SK 1011
Export boxing for
shipment of engine
equipped with front
support
Wooden
Use on units already
equipped with a front
support
SK-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SK/sk-Keydata.htm [3/15/2002 10:18:27 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 119/156
K 1005
K - Shipping Skid
vision Date: 05/00
ption # Description Disposition Material Notes
K 1005 Skid used with fan to flywheel engine. Wooden box No content option
content option.
oden box-type shipping skid used with fan to flywheel engine.
SK 1005
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SK/sk-1005.htm [3/15/2002 10:18:26 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 120/156
K 1006
K - Shipping Skid
vision Date: 05/00
ption # Description Disposition Material Notes
K 1006 Front shipping bracket and mounting screws for fan to flywheel bare engine Wooden skid Domestic use
nt shipping bracket and mounting screws for fan to flywheel bare engine on wooden shipping skid.
r domestic use only.
SK 1006
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SK/sk-1006.htm [3/15/2002 10:18:27 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 121/156
K 1007
K - Shipping Skid
vision Date: 05/00
ption # Description Disposition Material Notes
K 1007 Skid for fan to flywheel engine Wooden Domestic use only
content option.
oden shipping skid for fan to flywheel engine.
r domestic use only.
SK 1007
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SK/sk-1007.htm [3/15/2002 10:18:27 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 122/156
K 1008
K - Shipping Arrangement
vision Date: 05/00
ption # Description Disposition Material Notes
K 1008 Front shipping bracket for fan to flywheel bare engine Wooden skid For international use only
nt shipping bracket for fan to flywheel bare engine on wooden shipping skid
r international use only.
SK 1008
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SK/sk-1008.htm [3/15/2002 10:18:27 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 123/156
K 1011
K - Shipping Arrangement
vision Date: 05/00
ption # Description Disposition Material Notes
K 1011Export boxing for shipment of engine equipped with
front supportWooden
Use on units already equipped with a
front support
port boxing for shipment of engine equipped with front support.
es not contain shipping bracket.
es not contain shipping bracket.
e on units already equipped with a front support.
SK 1011
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SK/sk-1011.htm [3/15/2002 10:18:27 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 124/156
SP-Keydata
Option # Description Thickness Bolt Circle Dia. Notes
SP 10356 mm
[0.25 in.]
89 mm
[3.5 in.]
SP 103619 mm
[0.75 in.]
89 mm
[3.5 in.]
SP 10429 mm
[0.3 in.]
140 mm
[5.5 in.]
SP 104863 mm
[2.5 in.]
140 mm
[5.5 in.]
SP 1057 Fan spacer25 mm
[1.0 in.]
140 mm
[5.5 in.]
SP-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SP/sp-Keydata.htm [3/15/2002 10:18:32 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 125/156
P 1035
P - Fan Spacer
vision Date: 05/00
ption # Description Thickness Bolt Circle Dia. Notes
P 10356 mm
[0.25 in.]
89 mm
[3.5 in.]
pilot and spacer providing 6 mm [0.25 in.] total spacing. Has 51 mm [2.0 in.] fan pilot. Fits hubs with 65 mm [2.6 in.] bore. Six mo
es on 89 mm [3.5 in.] B.C.
SP 1035
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SP/sp-1035.htm [3/15/2002 10:18:28 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 126/156
P 1036
P - Fan Spacer
vision Date: 05/00
ption # Description Thickness Bolt Circle Dia. Notes
P 1036 19 mm[0.75 in.]
89 mm[3.5 in.]
pilot and spacer providing 19 mm [0.75 in.] total spacing. Has 51 mm [2.0 in.] fan pilot. Fits hubs with 65 mm [2.6 in.] bore. Six
unting holes on 89 mm [3.5 in.] B.C.
pplied in kit.
SP 1036
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SP/sp-1036.htm [3/15/2002 10:18:30 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 127/156
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 128/156
SP 1048
P - Fan Spacer
vision Date: 05/00
Option # Description Thickness Bolt Circle Dia. Notes
SP 104863 mm
[2.5 in.]
140 mm
[5.5 in.]
SP 1048
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SP/sp-1048.htm (1 of 2) [3/15/2002 10:18:31 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 129/156
n pilot and spacer providing 63 mm [2.5 in.] total spacing. Has 76 mm [3.0 in.] fan pilot. Fits hubs with 65 mm
] bore. Six mounting holes on 140 mm [5.5 in.] B.C.
SP 1048
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SP/sp-1048.htm (2 of 2) [3/15/2002 10:18:31 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 130/156
P 1057
P - Fan Spacer
vision Date: 05/00
ption # Description Thickness Bolt Circle Dia. Notes
P 1057 Fan spacer25 mm
[1.0 in.]
140 mm
[5.5 in.]
pilot and spacer providing 25 mm [1.0 in.] fan spacing. Has 76 mm [3.0 in.] fan pilot and six mounting holes on a 140 mm [5.5 in.]
SP 1057
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SP/sp-1057.htm [3/15/2002 10:18:32 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 131/156
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 132/156
S 1079
S - Paint
vision Date: 05/00
ption # Description
S 1079 Beige paint
mmins beige paint. Includes primer.
SS 1079
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/SS/ss-1079.htm [3/15/2002 10:18:33 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 133/156
ST-Keydata
Option # Voltage/kW Mfg/ModelPinion Gear Pitch
Notes
ST 1340 24V/25 kW Delco Remy 42MT 400 6/8Solenoid angle: 277.5
degrees
ST 1343Customer supplied
starting motor
ST-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/ST/st-Keydata.htm [3/15/2002 10:18:35 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 134/156
T 1340
T - Starting Motor
vision Date: 03/00
ption # Voltage/kW Mfg/Model Pinion Gear Pitch Notes
T 1340 24V/25 kW Delco Remy 42MT 400 6/8 Solenoid angle: 277.5 degrees
V Delco Remy 42MT, type 400 positive engagement starter with solenoid positioned at 277.5 deg. Right hand (clockwise) rotation.
IQUE CHARACTERISTICS: Insulated and with ground strap.rter Location: 2nd Quadrant
rter Length: 496 mm [19.53 in.]
ST 1340
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/ST/st-1340.htm [3/15/2002 10:18:34 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 135/156
T 1343
T - Starting Motor
vision Date: 05/00
ption # Voltage/kW Mfg/Model Pinion Gear Pitch Notes
T 1343 Customer supplied starting motor
content option for customer supplied motor.
ST 1343
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/ST/st-1343.htm [3/15/2002 10:18:34 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 136/156
TB-Keydata
Option # Mount/Exhaust Outlet Location Wastegate Water-Cooled Notes
TB 1342 High mount/front out No No JWAC
B-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/TB/tb-Keydata.htm [3/15/2002 10:18:36 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 137/156
B 1342
B - Turbocharger Arrangement
vision Date: 05/00
ption # Mount/Exhaust Outlet Location Wastegate Water-Cooled Notes
B 1342 High mount/front out No No JWAC
ee piece exhaust manifold and mounting for front out turbo with vertical mounting flange. Used with rear aftercooler plumbing. Incl
intake manifold, aftercooler core and mounting.
B 1342
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/TB/tb-1342.htm [3/15/2002 10:18:36 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 138/156
TH-Keydata
Option # Description Outlet Diameter Notes
TH 1139 64 mm [2.50 in.] and is oriented straight upward
TH 1141 64 mm [2.50 in.] and is oriented straight upward
H-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/TH/th-Keydata.htm [3/15/2002 10:18:37 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 139/156
TH 1139
H - Water Outlet Connection
evision Date: 03/00
Option # Description Outlet Diameter Notes
TH 1139 64 mm [2.50 in.] and is oriented straight upward
hermostat housing.
ual thermostat housing and mounting to water pump for engines without automatic transmissions a
ithout air compressor. Water outlet O.D. is cast 64 mm [2.50 in.] and is oriented straight upward.ocated 787 mm [31 in.] vertical and 203 mm [8.0 in.] outboard from the crankshaft centerline and 1
m [4.0 in.] rearward from FFOB.
H 1139
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/TH/th-1139.htm [3/15/2002 10:18:37 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 140/156
TH 1141
H - Water Outlet Connection
evision Date: 03/00
Option # Description Outlet Diameter Notes
TH 1141 64 mm [2.50 in.] and is oriented straight upward
hermostat housing.
ual thermostat housing and mounting to water pump. For engines without automatic transmissions
ithout air compressor. Water outlet O.D. is cast 64 mm [2.50 in.] and is oriented straight forward. Tutlet is located 762 mm [30 in.] up and 203 mm [8.0 in.] outboard from the crankshaft centerline an
m [1.0 in.] forward from the FFOB.
H 1141
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/TH/th-1141.htm [3/15/2002 10:18:37 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 141/156
VC-Keydata
Option # Description Oil Fill Location Breather Included Notes
VC 1031 Cast aluminum Over No. 1 cylinder YesBreather located over
No. 6 cylinder
VC 1037 Stamped steel Over No. 1 cylinder YesBreather located over
No. 6 cylinder
VC 1046 Cast aluminum Hand hole cover YesBreather located over
No. 6 cylinder
VC 1047 Stamped steel Hand hole cover YesBreather located over
No. 6 cylinder
VC-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/VC/vc-Keydata.htm [3/15/2002 10:18:39 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 142/156
C 1031
C - Valve Cover
vision Date: 05/00
ption # Description Oil Fill Location Breather Included Notes
C 1031 Cast aluminum Over No. 1 cylinder Yes Breather located over No. 6 cylinder
t aluminum red valve cover with oil fill over No. 1 cylinder and breather located over No. 6 cylinder.
VC 1031
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/VC/vc-1031.htm [3/15/2002 10:18:38 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 143/156
C 1037
C - Valve Cover
vision Date: 05/00
ption # Description Oil Fill Location Breather Included Notes
C 1037 Stamped steel Over No. 1 cylinder Yes Breather located over No. 6 cylinder
mped steel valve cover with oil fill over No. 1 cylinder and breather located over No. 6 cylinder.
VC 1037
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/VC/vc-1037.htm [3/15/2002 10:18:38 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 144/156
C 1046
C - Valve Cover
vision Date: 06/00
ption # Description Oil Fill Location Breather Included Notes
C 1046 Cast aluminum Hand hole cover Yes Breather located over No. 6 cylinder
t aluminum red valve cover with oil fill in hand hole cover and breather located over No. 6 cylinder.
VC 1046
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/VC/vc-1046.htm [3/15/2002 10:18:39 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 145/156
C 1047
C - Valve Cover
vision Date: 06/00
ption # Description Oil Fill Location Breather Included Notes
C 1047 Stamped steel Hand hole cover Yes Breather located over No. 6 cylinder
mped steel valve cover with oil fill in hand hole cover and breather located over No. 6 cylinder.
VC 1047
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/VC/vc-1047.htm [3/15/2002 10:18:39 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 146/156
VT-Keydata
Option # Location Notes
VT 1002Pan rail toward rear of engine
For use with non-CENTRY™ fuel pumps and without
SAE B hydraulic pump behind oil pump
VT-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/VT/vt-Keydata.htm [3/15/2002 10:18:40 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 147/156
T 1002
T - Variable Timing Valve Location
vision Date: 05/00
ption # Location Notes
T 1002 Pan rail toward rear of engineFor use with non-CENTRY™ fuel pumps and without SAE B hydraulic pump behind oil
pump
content option (only a pointer to selection) for low mount oil control valve located on pan rail toward rear of engine.
r use with or without fuel line check valves and without SAE-B hydraulic pump behind oil pump.
VT 1002
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/VT/vt-1002.htm [3/15/2002 10:18:40 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 148/156
WD-Keydata
Option # Location Notes
WD 1001 Exhaust side at rear of engine
WD-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/WD/wd-Keydata.htm [3/15/2002 10:18:42 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 149/156
WD 1001
D - Water Discharge Plumbing
vision Date: 05/00
Option # Location Notes
WD 1001 Exhaust side at rear of engine
incock for water jacket located on exhaust side at rear of engine.
haust side of engine in block.
WD 1001
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/WD/wd-1001.htm [3/15/2002 10:18:41 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 150/156
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 151/156
WF 1169
F - Corrosion Resistor
vision Date: 06/00
Option # Supplier/Type Mounting DCA4 Plus Units Notes
WF 1169 Cummins/spin-on Oil cooler 23 Coolant system capacity of 30–57 litres [8–15 U.S. gal.]
ter system corrosion filter. Filter head and mounting are integral part of oil cooler assembly. Contains one filter element with 23
ts, achieving a system concentration of 1.5–3.0 DCA units per cooling system gallon.
r use with cooling systems with capacities from 30.28 to 56.76 litres [8 to 15 U. S. gal.].
WF 1169
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/WF/wf-1169.htm [3/15/2002 10:18:44 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 152/156
WF 1195
F - Corrosion Resistor
vision Date: 05/00
Option # Supplier/Type Mounting DCA4 Plus Units Notes
WF 1195 Cummins/spin-on Oil cooler 4
ter system corrosion filter.
er head and mounting are integral part of cooler assembly.
A type: DCA4–Plus
A Units: 4
WF 1195
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/WF/wf-1195.htm [3/15/2002 10:18:44 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 153/156
WI-Keydata
Option # Inlet O.D. Orientation Notes
WI 1077 70 mm [2.75 in.] Pointing straight down
WI-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/WI/wi-Keydata.htm [3/15/2002 10:18:46 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 154/156
WI 1077
- Water Inlet Connection
vision Date: 05/00
ption # Inlet O.D. Orientation Notes
WI 1077 70 mm [2.75 in.] Pointing straight down
e piece water inlet connection. Has 70 mm [2.75 in.] O.D. hose connection located between oil filter and alternator pointing straight
1/2 NPT hole, 19.0 mm [0.75 in.] hole reduced to 13 mm [0.50 in], and 25.4 mm [1.00 in] hole plugged.
WI 1077
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/WI/wi-1077.htm [3/15/2002 10:18:45 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 155/156
XS-Keydata
Option # Description Connection O.D. Marmon Type Notes
XS 1041 90 deg. elbow 127 mm [5.0 in.] Yes
XS-Keydata
ttp://marketingtechdata.cummins.com/curves/database/options/n14g/n14g/XS/xs-Keydata.htm [3/15/2002 10:18:47 AM]
8/17/2019 N14 GDRIVE
http://slidepdf.com/reader/full/n14-gdrive 156/156
S 1041
S - Exhaust Outlet Connection
vision Date: 05/00
XS 1041
Recommended