View
224
Download
1
Category
Preview:
Citation preview
National Aeronautics and Space Administration
www.nasa.gov
Method to Generate Full-Span Ice Shape on Swept Wing Using Icing Tunnel Data
1
Sam LeeVantage Partners, LLC
Stephanie CamelloUniversity of Washington
https://ntrs.nasa.gov/search.jsp?R=20150019656 2018-06-28T02:09:32+00:00Z
National Aeronautics and Space Administration
www.nasa.gov 2
Introduction
• Current collaborative research program to improve the fidelity of experimental and computational simulation methods for swept-wing ice accretion formulations.• NASA, FAA, ONERA, and university partners.
• Utilize 65% scale Common Research Model.• Ice shapes obtained in NASA Icing Research Tunnel• Hybrid models from 20%, 64%, and 83% span used• Models have full-scale leading edge
• Full-span ice shapes required for aerodynamic testing.
National Aeronautics and Space Administration
www.nasa.gov
Introduction (cont’d)• Each IRT models can generate 1 ft span of ice.• Full-span ice shapes require 75 ft of ice.• Large gaps between the three spanwise ice
sections.• Method developed to generate full-span ice shapes
from the three 1 ft span ice shapes
National Aeronautics and Space Administration
www.nasa.gov 4
IRT Test Section
CRM -65%
Introduction (cont’d)
National Aeronautics and Space Administration
www.nasa.gov 5
Ice Scan Data Acquisition Procedure
The IRT scanner data acquisition procedure :1. Accrete ice on the test article2. Spray the ice with white paint3. Install and set up the scanner4. Scan the ice shape
National Aeronautics and Space Administration
www.nasa.gov 6
Ice Scan Data Processing Procedure
The IRT scanner data processing procedure consisted of the following five steps:
1. Align/combine scan passes2. Reduce data set3. Wrap surface4. Repair mesh/fill holes5. Coordinate transformation
National Aeronautics and Space Administration
www.nasa.gov 7
3D Ice Shape Scanning Methodology
Lee, S., Broeren, A.P., Addy., H.E., Sills, R., and Pifer, E., “Development of 3D Ice Accretion Measurement Method,” AIAA 4th Atmospheric and Space Environments Conference, New Orleans, LA, June 25-28, 2012, AIAA Paper 2012-2938.
Lee, S., Broeren, A.P., Kreeger, R.E., Potapczuk, M., and Utt, L., “Implementation and Validation of 3-D Ice Accretion Measurement Methodology,” AIAA 6th Atmospheric and Space Environments Conference, Atlanta, GA, June 16-20, 2014, AIAA Paper 2014-2613.
Broeren, AP, Addy, H.E., Lee, S., and Monastero, M.C., “Validation of 3-D Ice Accretion Measurement Methodology for Experimental Aerodynamic Simulation,” AIAA 6th Atmospheric and Space Environments Conference, Atlanta, GA, June 16-20, 2014, AIAA Paper 2014-2614.
National Aeronautics and Space Administration
www.nasa.gov 8
Ice Interpolation Methodology
• Interpolate ice shapes between the scanned sections.• Utilize weighted averaging function in Geomagic Studio.• Results in “morphing” of ice shape from scanned section
into an unscanned section.
• Demonstrated using existing scanned ice shapes from a swept NACA 0012 airfoil
National Aeronautics and Space Administration
www.nasa.gov 9
Begin with rime ice shapeBegin with scalloped
ice shape
Trim rimeice shape
Trim scalloped ice shape
Average the rime and scalloped ice shapes in layers using a
weighting technique
Line up averaged layers to create a smooth transition
Combine layers to createa single object
Ice Interpolation Methodolgy
National Aeronautics and Space Administration
www.nasa.gov 10
• A variety of combinations of rime, horn, and scalloped ice were morphed
• 3 main categories– Basic morphing on a straight wing– Twist and taper without morphing– Twist and taper with morphing
Ice Generation Methodology
National Aeronautics and Space Administration
www.nasa.gov 15
5° twist & 0.5 scale taper
Rime to Scallop With Twist and Taper
National Aeronautics and Space Administration
www.nasa.gov 16
NACA 0012, = 0°, = 45°
Comparison of Interpolation Method to Real Ice
National Aeronautics and Space Administration
www.nasa.gov 17
Actual Ice
Comparison of Interpolation Method to Real Ice
InterpolatedIce
National Aeronautics and Space Administration
www.nasa.gov
Conclusion
19
• Method developed to generate a full-span ice shape from partial spanwise section.
• Interpolated the ice shapes between the scanned sections using the weighted averaging function in Geomagic Studio.
• This procedure demonstrated using existing scanned ice shapes from a swept NACA 0012 airfoil.
• Initial results are promising.• It was used to interpolate ice shapes between horn and rime
shapes as well as scallop and rime shapes. This could also work with twisted and tapered wing.
• The ability to interpolate between two very different types of ice shape demonstrated.
National Aeronautics and Space Administration
www.nasa.gov
Conclusion (cont’d)
20
• The resultant interpolated or “morphed” ice shape usually contains some surface artifacts, such as spikes or repeated patterns.
• These will be removed using a commercially available software called Geomagic Freeform.
• This software allows the user to hand-manipulate the interpolated ice shapes and will be used to remove these artifacts and also perform final touch-up on the ice shapes.
Recommended